TLC2202CPS [TI]
Advanced linCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS;
| 型号： | TLC2202CPS |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | Advanced linCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS 放大器 光电二极管 |
| 文件： | 总71页 (文件大小：1904K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
D
B Grade Is 100% Tested for Noise
30 nV/√Hz Max at f = 10 Hz
12 nV/√Hz Max at f = 1 kHz
Low Input Offset Voltage . . . 500 µV Max
Excellent Offset Voltage Stability
D
D
D
Low Input Bias Current
1 pA Typ at T = 25°C
A
Common-Mode Input Voltage Range
Includes the Negative Rail
D
D
Fully Specified For Both Single-Supply and
Split-Supply Operation
With Temperature . . . 0.5 µV/°C Typ
D
Rail-to-Rail Output Swing
TYPICAL EQUIVALENT
INPUT NOISE VOLTAGE
vs
description
FREQUENCY
The TLC220x, TLC220xA, TLC220xB, and
TLC220xY are precision, low-noise operational
amplifiers using Texas Instruments Advanced
LinCMOS process. These devices combine the
noise performance of the lowest-noise JFET
amplifiers with the dc precision available
previously only in bipolar amplifiers. The
Advanced LinCMOS process uses silicon-gate
technology to obtain input offset voltage stability
with temperature and time that far exceeds that
obtainable using metal-gate technology. In
addition, this technology makes possible input
impedance levels that meet or exceed levels
offered by top-gate JFET and expensive
dielectric-isolated devices.
60
V
= 5 V
= 20 Ω
= 25°C
DD
S
R
T
50
40
30
20
10
0
A
The combination of excellent DC and noise
performance with a common-mode input voltage
range that includes the negative rail makes these
devices an ideal choice for high-impedance,
low-level signal-conditioning applications in either
single-supply or split-supply configurations.
1
10
100
1 k
10 k
f − Frequency − Hz
The device inputs and outputs are designed to withstand −100-mA surge currents without sustaining latch-up.
In addition, internal ESD-protection circuits prevent functional failures at voltages up to 2000 V as tested under
MIL-PRF-38535, Method 3015.2; however, care should be exercised in handling these devices as exposure
to ESD may result in degradation of the parametric performance.
The C-suffix devices are characterized for operation from 0°C to 70°C. The I-suffix devices are characterized
for operation from −40°C to 85°C. The M-suffix devices are characterized for operation over the full military
temperature range of −55°C to 125°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Advanced LinCMOS is a trademark of Texas Instruments Incorporated. All other trademarks are the property of their respective owners.
ꢙ
ꢙ
ꢚ
ꢒ
ꢊ
ꢭ
ꢟ
ꢌ
ꢮ
ꢂ
ꢡ
ꢀ
ꢎ
ꢨ
ꢗ
ꢞ
ꢒ
ꢍ
ꢝ
ꢖ
ꢬ
ꢭ
ꢇ
ꢀ
ꢇ
ꢐ
ꢍ
ꢏ
ꢟ
ꢬ
ꢞ
ꢎ
ꢎ
ꢝ
ꢢ
ꢌ
ꢌ
ꢍ
ꢠ
ꢠ
ꢐ
ꢐ
ꢜ
ꢞ
ꢞ
ꢝ
ꢍ
ꢍ
ꢞ
ꢐ
ꢡ
ꢡ
ꢜ
ꢡ
ꢎ
ꢟ
ꢠ
ꢪ
ꢝ
ꢧ
ꢝ
ꢏ
ꢏ
ꢍ
ꢠ
ꢌ
ꢢ
ꢡ
ꢡ
ꢡ
ꢍ
ꢞ
ꢬ
ꢜ
ꢟ
ꢯ
ꢡ
ꢡ
ꢣ
ꢐ
ꢎ
ꢌ
ꢡ
ꢠ
ꢐ
ꢠ
ꢫ
ꢞ
ꢝ
ꢍ
ꢟ
ꢊ
ꢌ
ꢍ
ꢊ
ꢠ
ꢠ
ꢏ
ꢡ
ꢏ
ꢩ
Copyright 1997−2008, Texas Instruments Incorporated
ꢒ ꢍ ꢜ ꢝ ꢞꢊ ꢟꢎ ꢠꢡ ꢎꢞ ꢢꢜ ꢣꢐ ꢌꢍ ꢠ ꢠꢞ ꢑꢗ ꢁꢕ ꢙꢚ ꢛ ꢕꢤꢥꢦ ꢤꢦꢆ ꢌꢣꢣ ꢜꢌ ꢝ ꢌ ꢢꢏ ꢠꢏꢝ ꢡ ꢌ ꢝ ꢏ ꢠꢏ ꢡꢠꢏ ꢊ
ꢝ
ꢞ
ꢎ
ꢠ
ꢞ
ꢝ
ꢢ
ꢠ
ꢞ
ꢡ
ꢜ
ꢐ
ꢬ
ꢐ
ꢎ
ꢏ
ꢝ
ꢠ
ꢏ
ꢝ
ꢞ
ꢬ
ꢀ
ꢏ
ꢅ
ꢌ
ꢗ
ꢍ
ꢢ
ꢏ
ꢡ
ꢠ
ꢌ
ꢍ
ꢊ
ꢝꢊ
ꢌ
ꢠ ꢏ ꢡ ꢠꢐ ꢍꢪ ꢞꢬ ꢌ ꢣꢣ ꢜꢌ ꢝ ꢌ ꢢ ꢏ ꢠ ꢏ ꢝ ꢡ ꢩ
ꢝ
ꢌ
ꢍ
ꢠꢫ
ꢩ
ꢙ
ꢝ
ꢞ
ꢊ
ꢠ
ꢐ
ꢞ
ꢎ
ꢏ
ꢡꢐ
ꢍ
ꢊ
ꢞ
ꢏ
ꢞ
ꢠ
ꢍ
ꢏ
ꢎ
ꢏ
ꢡ
ꢌ
ꢝ
ꢐ
ꢣ
ꢐ
ꢍ
ꢎ
ꢣ
ꢟ
ꢟ ꢍꢣ ꢏꢡꢡ ꢞ ꢠꢧꢏ ꢝ ꢨꢐ ꢡꢏ ꢍ ꢞꢠꢏ ꢊꢩ ꢒ ꢍ ꢌꢣ ꢣ ꢞ ꢠꢧꢏ ꢝ ꢜꢝ ꢞ ꢊꢟꢎ ꢠꢡ ꢆ ꢜꢝ ꢞ ꢊꢟꢎ ꢠꢐꢞ ꢍ
ꢠ
ꢜ
ꢝ
ꢞꢎ
ꢏ
ꢡ
ꢡ
ꢐ
ꢍꢪ
ꢊ
ꢞꢏ
ꢡ
ꢍ
ꢞ
ꢠ
ꢍ
ꢏ
ꢎ
ꢏ
ꢡ
ꢡ
ꢌ
ꢝ
ꢐ
ꢣꢫ
ꢐ
ꢍ
ꢎ
ꢣ
ꢟ
ꢊ
ꢏ
ꢠ
ꢏ
ꢡ
ꢐ
ꢍ
ꢪ
ꢞ
ꢬ
ꢌ
ꢣ
ꢣ
ꢜ
ꢌ
ꢝ
ꢌ
ꢢꢏ
ꢠ
ꢏꢝ
ꢡ
ꢩ
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ
ꢁ
ꢂ
ꢃ
ꢃ
ꢄ
ꢅ
ꢆ
ꢀ
ꢁ
ꢂ
ꢃ
ꢃ
ꢄ
ꢅ
ꢇ
ꢆ
ꢀ
ꢁ
ꢂ
ꢃ
ꢃ
ꢄ
ꢅ
ꢈ
ꢆ
ꢀ
ꢁ
ꢂ
ꢃ
ꢃ
ꢄ
ꢅ
ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201 AVAILABLE OPTIONS
PACKAGED DEVICES
V max
n
V max
n
CHIP
FORM
(Y)
V
max
SMALL
OUTLINE
(D)
CHIP
CARRIER
(FK)
CERAMIC
DIP
PLASTIC
DIP
IO
‡
T
A
f = 10 Hz
f = 1 kHz
AT 25°C
†
AT 25°C
AT 25°C
(JG)
(P)
200 µV
200 µV
500 µV
200 µV
200 µV
500 µV
200 µV
200 µV
500 µV
TLC2201ACD
TLC2201BCD
TLC2201CD
TLC2201AID
TLC2201BID
TLC2201ID
TLC2201ACP
TLC2201BCP
TLC2201CP
TLC2201AIP
TLC2201BIP
TLC2201IP
35 nV/√Hz 15 nV/√Hz
30 nV/√Hz 12 nV/√Hz
0°C to 70°C
−40°C to 85°C
−55°C to 125°C
—
—
—
—
TLC2201Y
—
—
35 nV/√Hz 15 nV/√Hz
30 nV/√Hz 12 nV/√Hz
—
—
—
—
TLC2201AMD TLC2201AMFK TLC2201AMJG TLC2201AMP
TLC2201BMD TLC2201BMFK TLC2201BMJG TLC2201BMP
35 nV/√Hz 15 nV/√Hz
30 nV/√Hz 12 nV/√Hz
TLC2201MD
TLC2201MFK
TLC2201MJG
TLC2201MP
—
—
†
‡
The D packages are available taped and reeled. Add R suffix to device type (e.g. TLC220xBCDR).
Chip forms are tested at 25°C only.
TLC2202 AVAILABLE OPTIONS
PACKAGED DEVICES
PLASTIC
SMALL
OUTLINE
(PS)
CHIP
FORM
(Y)
V max
n
V max
n
V
max
SMALL
OUTLINE
(D)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(JG)
PLASTIC
DIP
IO
‡
T
f = 10 Hz
f = 1 kHz
A
†
AT 25°C
AT 25°C
AT 25°C
(P)
500 µV
500 µV
1 mV
TLC2202BCD
TLC2202ACD
TLC2202CD
TLC2202BID
TLC2202AID
TLC2202ID
—
—
—
—
—
—
—
—
—
—
—
—
—
TLC2202BCP
TLC2202ACP
TLC2202CP
TLC2202BIP
TLC2202AIP
TLC2202IP
30 nV/√Hz 12 nV/√Hz
35 nV/√Hz 15 nV/√Hz
—
0°C to 70°C
−40°C to 85°C
−55°C to 125°C
TLC2202Y
TLC2202CPSR
—
—
500 µV
500 µV
1 mV
—
—
—
—
—
—
30 nV/√Hz 12 nV/√Hz
35 nV/√Hz 15 nV/√Hz
—
—
—
—
500 µV
500 µV
1 mV
TLC2202BMD
TLC2202AMD
TLC2202MD
TLC2202BMFK TLC2202BMJG TLC2202BMP
TLC2202AMFK TLC2202AMJG TLC2202AMP
30 nV/√Hz 12 nV/√Hz
35 nV/√Hz 15 nV/√Hz
TLC2202MFK
TLC2202MJG
TLC2202MP
—
—
†
‡
The D packages are available taped and reeled. Add R suffix to device type (e.g. TLC220xBCDR).
Chip forms are tested at 25°C only.
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201
D, JG, OR P PACKAGE
(TOP VIEW)
TLC2202
PS, JG, OR P PACKAGE
(TOP VIEW)
TLC2202
D PACKAGE
(TOP VIEW)
NC
NC
NC
NC
V
1
2
3
4
5
6
7
14
13
12
11
10
9
NC
IN−
IN+
NC
V
OUT
1OUT
1IN−
1IN+
/GND
V
DD+
1
2
3
4
8
7
6
5
1
2
3
4
8
7
6
5
2OUT
2IN−
2IN+
DD+
1OUT
1IN−
1IN+
/GND
DD+
2OUT
2IN−
2IN+
NC
V
/GND
NC
V
DD−
DD−
V
DD−
NC
8
TLC2201
FK PACKAGE
(TOP VIEW)
TLC2202
FK PACKAGE
(TOP VIEW)
3
2
1
20 19
18
NC
V
NC
IN−
NC
IN+
NC
4
5
6
7
8
3
2
1
20 19
18
NC
NC
4
5
6
7
8
17
16
15
14
DD+
2OUT
NC
1IN−
NC
17
16
15
14
NC
OUT
NC
2IN−
NC
1IN+
NC
9 10 11 12 13
9 10 11 12 13
NC − No internal connection
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
equivalent schematic (each amplifier)
V
DD+
Q3
Q6
Q9
Q12
Q14
Q16
IN +
IN −
OUT
C1
Q1
Q4
Q13
Q15
Q17
D1
Q7
Q8
Q10
Q11
R1
R2
Q2
Q5
V
DD−
/GND
ACTUAL DEVICE COMPONENT COUNT
COMPONENT
Transistors
Resistors
TLC2201
TLC2202
17
2
34
2
Diodes
1
4
Capacitors
1
2
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201Y chip information
This chip, when properly assembled, displays characteristics similar to the TLC2201C. Thermal compression
or ultrasonic bonding may be used on the doped-aluminum bonding path. Chips may be mounted with
conductive epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS
V
DD+
(7)
(2)
(3)
(8)
(7)
(6)
+
IN−
IN+
(6)
OUT
−
(4)
V
DD−
77
CHIP THICKNESS: 15 MILS TYPICAL
BONDING PADS: 4 × 4 MILS MINIMUM
T max = 150°C
J
TOLERANCES ARE 10%.
ALL DIMENSIONS ARE IN MILS.
PIN (4) IS INTERNALLY CONNECTED
TO BACK SIDE OF CHIP.
(1)
(2)
(3)
(4)
TERMINAL NUMBERS ARE FOR THE
D, JG, AND P PACKAGES.
65
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202Y chip formation
This chip, when properly assembled, displays characteristics similar to the TLC2202C. Thermal compression
or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with
conductive epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS
V
DD+
(8)
(8)
(7)
(6)
(5)
(3)
(2)
1IN+
1IN−
+
−
(1)
1OUT
(5)
(6)
+
2IN+
2IN−
(7)
2OUT
−
(4)
80
V
DD−
CHIP THICKNESS: 15 MILS TYPICAL
BONDING PADS: 4 × 4 MILS MINIMUM
T max = 150°C
J
(4)
(3)
TOLERANCES ARE 10%.
ALL DIMENSIONS ARE IN MILS.
PIN (4) IS INTERNALLY CONNECTED
TO BACKSIDE OF CHIP.
(1)
(2)
100
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
†
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage, V
Supply voltage, V
(see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −8 V
DD+
DD−
Differential input voltage, V (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 V
ID
Input voltage, V (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V
I
Input current, I (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 mA
I
Output current, I (each output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
O
Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited
Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, T : C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
A
I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C
M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 125°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, PS, or P package . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: JG package . . . . . . . . . . . . . . . . . . . . 300°C
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values except differential voltages are with respect to the midpoint between V
and V .
DD+
DD−
2. Differential voltages are at IN+ with respect to IN−.
3. The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum
dissipation rating in not exceeded.
DISSIPATION RATING TABLE
T
≤ 25°C
DERATING FACTOR
T
= 70°C
T
= 85°C
T = 125°C
A
A
A
A
PACKAGE
POWER RATING
ABOVE T = 25°C
POWER RATING POWER RATING POWER RATING
A
D−8
D−14
PS
725 mW
5.8 mW/°C
7.6 mW/°C
6.2 mW/°C
11.0 mW/°C
8.4 mW/°C
8.0 mW/°C
464 mW
608 mW
496 mW
880 mW
672 mW
640 mW
377 mW
494 mW
403 mW
715 mW
546 mW
520 mW
145 mW
190 mW
155 mW
275 mW
210 mW
200 mW
950 mW
770 mW
FK
1375 mW
1050 mW
1000 mW
JG
P
recommended operating conditions
C SUFFIX
MIN MAX
I SUFFIX
M SUFFIX
UNIT
MIN
MAX
MIN
MAX
Supply voltage, V
DD
2.3
8
2.3
8
2.3
8
V
V
Common-mode input voltage, V
IC
V
V
DD+
−2.3
V
V
−2.3
DD+
85
V
V
−2.3
DD+
125
DD−
0
DD−
−40
DD−
−55
Operating free-air temperature, T
70
°C
A
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ
ꢁ
ꢂ
ꢃ
ꢃ
ꢄ
ꢅ
ꢆ
ꢀ
ꢁ
ꢂ
ꢃ
ꢃ
ꢄ
ꢅ
ꢇ
ꢆ
ꢀ
ꢁ
ꢂ
ꢃ
ꢃ
ꢄ
ꢅ
ꢈ
ꢆ
ꢀ
ꢁ
ꢂ
ꢃ
ꢃ
ꢄ
ꢅ
ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ
ꢒ
ꢔ
ꢕ
ꢖ
ꢒ
ꢗ
ꢓ
ꢘ
ꢙ
ꢚ
ꢘ
ꢂ
ꢗ
ꢓ
ꢗ
ꢒ
ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201C electrical characteristics at specified free-air temperature, V
otherwise noted)
=
5 V (unless
DD
TLC2201C
†
PARAMETER
TEST CONDITIONS
T
A
UNIT
MAX
MIN
TYP
25°C
100
500
V
IO
Input offset voltage
µV
Full range
600
α
Temperature coefficient of input offset voltage
Input offset voltage long-term drift (see Note 4)
Full range
25°C
0.5
µV/°C
VIO
0.001 0.005 µV/mo
V
IC
= 0,
R
= 50 Ω
S
25°C
0.5
1
60
100
60
I
I
Input offset current
Input bias current
pA
pA
IO
Full range
25°C
IB
Full range
100
−5
to
2.7
V
Common-mode input voltage range
R
R
= 50 Ω
Full range
V
ICR
S
25°C
Full range
25°C
4.7
4.7
4.8
−4.9
560
V
V
Maximum positive peak output voltage swing
Maximum negative peak output voltage swing
V
V
OM+
= 10 kΩ
L
−4.7
−4.7
400
300
90
OM−
Full range
25°C
V
O
=
=
4 V,
4 V,
R
R
= 500 kΩ
L
Full range
25°C
A
VD
Large-signal differential voltage amplification
V/mV
100
V
V
= 10 kΩ
O
L
Full range
70
= V
ICR
= 50 Ω
min,
V
= 0,
IC
O
CMRR Common-mode rejection ratio
Full range
85
dB
dB
R
S
25°C
Full range
25°C
90
85
110
1.1
k
Supply voltage rejection ratio (∆V
/∆V
IO
)
V = 2.3 V to 8 V
DD
SVR
DD
1.5
1.5
I
Supply current
V
O
= 0,
No load
mA
DD
Full range
†
Full range is 0°C to +70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2201C operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2201C
†
PARAMETER
TEST CONDITIONS
T
A
UNIT
V/µs
MIN
TYP
MAX
V
C
=
2.3 V,
= 100 pF
R
= 10 kΩ,
25°C
Full range
25°C
2
2.7
O
L
L
SR
Slew rate at unity gain
1.5
f = 10 Hz
18
8
nV/√Hz
V
n
Equivalent input noise voltage
f = 1 kHz
25°C
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
25°C
0.5
0.7
0.6
V
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
µV
N(PP)
25°C
I
n
25°C
fA/√Hz
MHz
f = 10 kHz,
R
C
= 10 kΩ,
L
L
Gain-bandwidth product
25°C
25°C
1.9
C
= 100 pF
L
φ
m
Phase margin at unity gain
R
= 10 kΩ,
= 100 pF
48°
L
†
Full range is 0°C to +70°C.
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201C electrical characteristics at specified free-air temperature, V
otherwise noted)
=
5 V (unless
DD
TLC2201AC
TLC2201BC
MIN TYP MAX
†
PARAMETER
TEST CONDITIONS
T
A
UNIT
MIN
TYP MAX
25°C
80
200
300
80
200
300
V
IO
Input offset voltage
µV
Full range
Temperature coefficient of input
offset voltage
α
VIO
Full range
0.5
0.5
µV/°C
Input offset voltage long-term
drift (see Note 4)
25°C
0.001 0.005
0.001 0.005 µV/mo
V
IC
= 0,
R
= 50 Ω
S
25°C
Full range
25°C
0.5
1
60
100
60
0.5
60
100
60
I
I
Input offset current
Input bias current
pA
IO
1
pA
V
IB
Full range
100
100
Common-mode input voltage
range
−5 to
2.7
−5 to
2.7
V
V
V
R
R
= 50 Ω
Full range
ICR
S
L
25°C
Full range
25°C
4.7
4.7
4.8
4.7
4.7
4.8
Maximum positive peak output
voltage swing
V
V
OM+
OM−
= 10 kΩ
−4.7 −4.9
−4.7
−4.7 −4.9
−4.7
Maximum negative peak output
voltage swing
Full range
25°C
400
300
90
560
100
115
110
1.1
400
300
90
560
100
115
110
1.1
V
V
=
=
4 V,
4 V,
R
R
= 500 kΩ
= 10 kΩ
O
L
L
Full range
25°C
Large-signal differential voltage
amplification
A
V/mV
VD
O
Full range
25°C
70
70
V
V
= V
ICR
min,
90
90
IC
CMRR Common-mode rejection ratio
Supply voltage rejection ratio
dB
dB
= 0,
R
= 50 Ω
Full range
25°C
85
85
O
S
90
90
k
V
=
2.3 V to 8 V
No load
SVR
DD
= 0,
(∆V
DD
/∆V )
IO
Full range
25°C
85
85
1.5
1.5
1.5
1.5
I
Supply current
V
O
mA
DD
Full range
†
Full range is 0°C to +70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201C operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2201AC
TLC2201BC
†
PARAMETER
TEST CONDITIONS
T
A
UNIT
V/µs
MIN
2
TYP MAX
MIN
TYP MAX
2.7
R
= 10 kΩ,
25°C
Full range
25°C
2.7
2
V
C
=
2.3 V,
L
O
L
SR
Slew rate at unity gain
= 100 pF
1.5
1.5
f = 10 Hz
18
8
35
15
18
30
12
Equivalent input noise volt-
age (see Note 5)
nV/√Hz
V
n
f = 1 kHz
25°C
8
0.5
0.7
0.6
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
25°C
0.5
0.7
0.6
Peak-to-peak equivalent input
noise voltage
V
N(PP)
µV
25°C
I
n
Equivalent input noise current
25°C
fA/√Hz
MHz
R
C
= 10 kΩ,
f = 10 kHz,
L
L
Gain-bandwidth product
25°C
25°C
1.9
1.9
C
= 100 pF
L
L
φ
m
Phase margin at unity gain
R
= 10 kΩ,
= 100 pF
48°
48°
†
Full range is 0°C to +70°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201C electrical characteristics at specified free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC2201C
UNIT
†
PARAMETER
TEST CONDITIONS
T
A
MIN
TYP
MAX
500
25°C
100
V
IO
Input offset voltage
µV
Full range
Full range
25°C
600
α
VIO
Temperature coefficient of input offset voltage
Input offset voltage long-term drift (see Note 4)
0.5
µV/°C
0.001 0.005 µV/mo
V
IC
= 0,
R
= 50 Ω
S
25°C
0.5
60
100
60
I
I
Input offset current
Input bias current
pA
pA
IO
Full range
25°C
1
IB
Full range
100
0
to
2.7
V
Common-mode input voltage range
R
R
= 50 Ω
Full range
V
ICR
S
L
25°C
Full range
25°C
4.7
4.7
4.8
0
V
V
Maximum high-level output voltage
Maximum low-level output voltage
= 10 kΩ
V
OH
50
50
I
O
= 0
mV
OL
Full range
25°C
150
100
25
315
55
V
O
R
= 1 V to 4 V,
= 500 kΩ
Full range
25°C
L
A
VD
Large-signal differential voltage amplification
V/mV
V
R
= 1 V to 4 V,
= 10 kΩ
O
Full range
25°C
15
L
90
110
110
1
V
R
= V
ICR
= 50 Ω
min,
V
= 0,
IC
O
CMRR Common-mode rejection ratio
dB
dB
Full range
25°C
85
S
90
k
Supply voltage rejection ratio (∆V
/∆V
IO
)
V = 4.6 V to 16 V
DD
SVR
DD
Full range
25°C
85
1.5
1.5
I
Supply current
V
O
= 2.5 V,
No load
mA
DD
Full range
†
Full range is 0°C to +70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2201C operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2201C
†
PARAMETER
TEST CONDITIONS
T
A
UNIT
V/µs
MIN
1.8
TYP
MAX
V
= 0.5 V to 2.5 V,
25°C
Full range
25°C
2.5
O
SR
Slew rate at unity gain
R
= 10 kΩ,
C
= 100 pF
1.3
L
L
f = 10 Hz
18
8
nV/√Hz
V
n
Equivalent input noise voltage
f = 1 kHz
25°C
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
25°C
0.5
0.7
0.6
V
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
µV
N(PP)
25°C
I
n
25°C
fA/√Hz
MHz
f = 10 kHz,
R
C
= 10 kΩ,
L
L
Gain-bandwidth product
25°C
25°C
1.8
C
= 100 pF
L
φ
m
Phase margin at unity gain
R
= 10 kΩ,
= 100 pF
45°
L
†
Full range is 0°C to +70°C.
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ
ꢒ
ꢔ
ꢕ
ꢖ
ꢒ
ꢗ
ꢓ
ꢘ
ꢙ
ꢚ
ꢘ
ꢂ
ꢗ
ꢓ
ꢗ
ꢒ
ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201C electrical characteristics at specified free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC2201AC
TLC2201BC
UNIT
†
PARAMETER
TEST CONDITIONS
T
A
MIN
TYP MAX
MIN
TYP MAX
25°C
80
200
300
80
200
300
V
IO
Input offset voltage
µV
Full range
Temperature coefficient of
input offset voltage
α
VIO
Full range
0.5
0.5
µV/°C
Input offset voltage long-term
drift (see Note 4)
25°C
0.001 0.005
0.001 0.005 µV/mo
V
IC
= 0,
R = 50 Ω
S
25°C
Full range
25°C
0.5
1
60
100
60
0.5
60
100
60
I
I
Input offset current
Input bias current
pA
pA
V
IO
1
IB
Full range
100
100
Common-mode input voltage
range
0 to
2.7
0 to
2.7
V
V
V
R
R
= 50 Ω
Full range
ICR
OH
OL
S
L
25°C
Full range
25°C
4.7
4.7
4.8
0
4.7
4.7
4.8
0
Maximum high-level output
voltage
= 10 kΩ
V
50
50
50
50
Maximum low-level output
voltage
I
O
= 0
mV
Full range
25°C
150
100
25
315
55
150
100
25
315
55
V
O
R
= 1 V to 4 V,
= 500 kΩ
Full range
25°C
L
Large-signal differential
voltage amplification
A
V/mV
VD
V
R
= 1 V to 4 V,
= 10 kΩ
O
Full range
25°C
15
15
L
V
V
= V
min,
90
110
110
1
90
110
110
1
IC
ICR
CMRR Common-mode rejection ratio
Supply voltage rejection ratio
dB
dB
= 0,
R
= 50 Ω Full range
25°C
85
85
O
S
90
90
k
V = 4.6 V to 16 V
DD
SVR
(∆V
DD
/∆V )
IO
Full range
25°C
85
85
1.5
1.5
1.5
1.5
I
Supply current
V
O
= 2.5 V,
No load
mA
DD
Full range
†
Full range is 0°C to +70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201C operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2201AC
TLC2201BC
†
PARAMETER
TEST CONDITIONS
T
A
UNIT
V/µs
MIN
1.8
TYP MAX
MIN
1.8
TYP MAX
V
= 0.5 V to 2.5 V,
25°C
2.5
2.5
O
SR
Slew rate at unity gain
R
= 10 kΩ,
C
= 100 pF Full range
1.3
1.3
L
L
f = 10 Hz
25°C
25°C
25°C
25°C
25°C
18
8
35
15
18
8
30
12
Equivalent input noise voltage
(see Note 5)
nV/√Hz
µV
V
n
f = 1 kHz
f = 0.1 to 1 Hz
0.5
0.7
0.6
0.5
0.7
0.6
Peak-to-peak equivalent input
noise voltage
V
N(PP)
f = 0.1 to 10 Hz
I
n
Equivalent input noise current
Gain-bandwidth product
fA/√Hz
f = 10 kHz,
R
= 10 kΩ,
25°C
L
L
1.8
1.8
MHz
C
= 100 pF
L
L
φ
m
Phase margin at unity gain
R
= 10 kΩ,
C
= 100 pF
25°C
45°
45°
†
Full range is 0°C to +70°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202C electrical characteristics at specified free-air temperature, V
otherwise specified)
=
5 V (unless
DD
TLC2202C
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
MAX
MIN
TYP
25°C
Full range
Full range
25°C
100
1000
V
Input offset voltage
µV
IO
1150
α
VIO
Temperature coefficient of input offset voltage
Input offset voltage long-term drift (see Note 4)
0.5
µV/°C
0.001 0.005 µV/mo
V
= 0,
R
= 50 Ω
S
IC
25°C
0.5
60
100
60
I
I
Input offset current
Input bias current
IO
Full range
25°C
pA
V
1
IB
Full range
100
−5
to
2.7
V
ICR
Common-mode input voltage range
R
R
= 50 Ω
Full range
S
25°C
Full range
25°C
4.7
4.7
−4.7
−4.7
300
200
50
4.8
−4.9
560
100
115
110
1.8
V
V
Maximum positive peak output voltage swing
Maximum negative peak output voltage swing
OM+
V
V
= 10 kΩ
L
OM−
Full range
25°C
V
O
=
=
4 V,
4 V,
R
R
= 500 kΩ
= 10 kΩ
L
Full range
25°C
A
VD
Large-signal differential voltage amplification
V/mV
V
V
O
L
Full range
25°C
25
80
= 0,
= 50 Ω
V
= V min,
ICR
O
IC
CMRR Common-mode rejection ratio
dB
dB
R
Full range
25°C
80
S
80
k
Supply-voltage rejection ratio (∆V
/∆V
IO
)
V
DD
=
2.3 V to 8 V
No load
SVR
DD
Full range
25°C
80
2.7
2.7
I
Supply current
V
O
= 0,
mA
DD
Full range
†
Full range is 0°C to +70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2202C operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2202C
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
V/µs
MIN
TYP
MAX
25°C
Full range
25°C
1.8
1.3
2.7
V
C
=
2.3 V,
= 100 pF
R
= 10 kΩ,
O
L
L
SR
Slew rate at unity gain
f = 10 Hz
18
8
V
n
Equivalent input noise voltage
nV/√Hz
f = 1 kHz
25°C
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
25°C
0.5
0.7
0.6
V
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
µV
N(PP)
25°C
I
n
25°C
fA/√Hz
MHz
f = 10 kHz,
R
C
= 10 kΩ,
L
L
Gain-bandwidth product
25°C
25°C
1.9
C
= 100 pF
L
L
φ
m
Phase margin at unity gain
R
= 10 kΩ,
= 100 pF
48°
†
Full range is 0°C to +70°C.
14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202C electrical characteristics at specified free-air temperature, V
otherwise noted)
=
5 V (unless
DD
TLC2202AC
TLC2202BC
MIN TYP MAX
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
µV
MIN
TYP MAX
25°C
80
500
650
80
500
650
V
IO
Input offset voltage
Full range
Temperature coefficient
of input offset voltage
α
VIO
Full range
0.5
0.5
µV/°C
Input offset voltage long-term
drift (see Note 4)
25°C
0.001 0.005
0.001 0.005 µV/mo
V
IC
= 0,
R
= 50 Ω
S
25°C
Full range
25°C
0.5
1
60
100
60
0.5
60
100
60
I
I
Input offset current
Input bias current
pA
pA
IO
1
IB
Full range
100
100
−5
to
2.7
−5
to
2.7
Common-mode input voltage
range
V
R
R
= 50 Ω
Full range
V
ICR
S
L
25°C
Full range
25°C
4.7
4.7
4.8
4.7
4.7
4.8
Maximum positive peak
output voltage swing
V
V
V
V
OM+
= 10 kΩ
−4.7 −4.9
−4.7
−4.7 −4.9
−4.7
Maximum negative peak
output voltage swing
OM−
Full range
25°C
300
200
50
560
100
115
110
1.8
300
200
50
560
100
115
110
1.8
V
V
=
=
4 V,
4 V,
R
R
= 500 kΩ
= 10 kΩ
O
L
L
Full range
25°C
Large-signal differential
voltage amplification
A
VD
V/mV
O
Full range
25°C
25
25
80
80
V
IC
V
O
= V
= 0,
min,
R
ICR
CMRR Common-mode rejection ratio
Supply-voltage rejection ratio
dB
dB
= 50 Ω
Full range
25°C
80
80
S
80
80
k
V
=
2.3 V to 8 V
No load
SVR
DD
= 0,
(∆V
DD
/∆V )
IO
Full range
25°C
80
80
2.7
2.7
2.7
2.7
I
Supply current
V
O
mA
DD
Full range
†
Full range is 0°C to +70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2202C operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2202AC
TLC2202BC
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
MIN
1.8
TYP MAX
MIN
1.8
1.3
TYP MAX
2.7
25°C
Full range
25°C
2.7
V
R
=
2.3 V,
O
SR
Slew rate at unity gain
V/µs
= 10 kΩ, C = 100 pF
1.3
L
L
f = 10 Hz
18
8
35
15
18
30
12
Equivalent input noise voltage
(see Note 5)
nV/√Hz
V
n
f = 1 kHz
25°C
8
0.5
0.7
0.6
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
25°C
0.5
0.7
0.6
Peak-to-peak equivalent input
noise voltage
V
I
µV
N(PP)
25°C
Equivalent input noise current
25°C
fA/√Hz
MHz
n
f = 10 kHz,
R = 10 kΩ,
L
Gain-bandwidth product
25°C
25°C
1.9
1.9
C
= 100 pF
L
L
φ
m
Phase margin at unity gain
R
= 10 kΩ, C = 100 pF
48°
48°
L
†
Full range is 0°C to +70°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202C electrical characteristics at specified free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC2202C
UNIT
†
T
A
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
1000
1150
25°C
100
V
IO
Input offset voltage
µV
Full range
Full range
25°C
α
VIO
Temperature coefficient of input offset voltage
Input offset voltage long-term drift (see Note 4)
0.5
µV/°C
0.001 0.005 µV/mo
V
IC
= 0,
R
= 50 Ω
S
25°C
0.5
60
100
60
pA
pA
I
I
Input offset current
Input bias current
IO
Full range
25°C
1
IB
Full range
100
0
to
2.7
V
Common-mode input voltage range
R
R
= 50 Ω
Full range
V
ICR
S
L
25°C
Full range
25°C
4.7
4.7
4.8
0
V
V
Maximum high-level output voltage
Maximum low-level output voltage
= 10 kΩ
V
OH
50
50
I
O
= 0
mV
OL
Full range
25°C
150
100
25
315
55
V
O
R
=1 V to 4 V,
= 500 kΩ
Full range
25°C
L
A
VD
Large-signal differential voltage amplification
V/mV
V
R
= 1 V to 4 V,
= 10 kΩ
O
Full range
25°C
15
L
75
110
110
1.7
V
R
= 0,
= 50 Ω
V
= V min,
ICR
O
IC
CMRR Common-mode rejection ratio
dB
dB
Full range
25°C
75
S
80
k
Supply-voltage rejection ratio (∆V
/∆V
IO
)
V = 4.6 V to 16 V
DD
SVR
DD
Full range
25°C
80
2.6
2.6
I
Supply current
V
O
= 0,
No load
mA
DD
Full range
†
Full range is 0°C to +70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2202C operating characteristics at specified free-air temperature, V
= 5 V
DD
†
TLC2202C
T
A
PARAMETER
TEST CONDITIONS
UNIT
V/µs
MIN
1.6
TYP
MAX
25°C
Full range
25°C
2.5
V
R
= 0.5 V to 2.5 V,
O
L
SR
Slew rate at unity gain
= 10 kΩ,
C
= 100 pF
L
1.1
f = 10 Hz
18
8
nV/√Hz
V
V
Equivalent input noise voltage
n
f = 1 kHz
25°C
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
25°C
0.5
0.7
0.6
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
µV
N(PP)
25°C
I
n
25°C
fA/√Hz
MHz
f = 10 kHz,
R
C
= 10 kΩ,
L
L
Gain-bandwidth product
25°C
25°C
1.9
C
= 100 pF
L
L
φ
m
Phase margin at unity gain
R
= 10 kΩ,
= 100 pF
47°
†
Full range is 0°C to +70°C.
16
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202C electrical characteristics at specified free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC2202AC
TLC2202BC
UNIT
†
T
A
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
MIN
TYP MAX
25°C
80
500
650
80
500
650
V
IO
Input offset voltage
µV
Full range
Temperature coefficient
of input offset voltage
α
VIO
Full range
0.5
0.5
µV/°C
Input offset voltage
long-term drift (see Note 4)
25°C
0.001 0.005
0.001 0.005 µV/mo
V
IC
= 0,
R = 50 Ω
S
25°C
Full range
25°C
0.5
1
60
100
60
0.5
60
100
60
I
I
Input offset current
Input bias current
pA
pA
IO
1
IB
Full range
100
100
0
to
2.7
0
to
2.7
Common-mode input
voltage range
V
R
R
= 50 Ω
Full range
V
ICR
S
L
25°C
Full range
25°C
4.7
4.7
4.8
0
4.7
4.7
4.8
0
Maximum high-level
output voltage
V
V
= 10 kΩ
V
OH
50
50
50
50
Maximum low-level
output voltage
I
O
= 0
mV
OL
Full range
25°C
150
100
25
315
55
150
100
25
315
55
V
R
= 1 V to 4 V,
= 500 kΩ
O
Full range
25°C
L
Large-signal differential
voltage amplification
A
VD
V/mV
V
R
= 1 V to 4 V,
= 10 kΩ
O
Full range
25°C
15
15
L
75
110
110
1.7
75
110
110
1.7
V
IC
V
O
= V
= 0,
min,
R
ICR
CMRR Common-mode rejection ratio
Supply-voltage rejection ratio
dB
dB
= 50 Ω
Full range
25°C
75
75
S
80
80
k
V = 4.6 V to 16 V
DD
SVR
(∆V
DD
/∆V )
IO
Full range
25°C
80
80
2.6
2.6
2.6
2.6
I
Supply current
V
O
= 2.5 V, No load
mA
DD
Full range
†
Full range is 0°C to +70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2202C operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2202AC
TLC2202BC
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
MIN
1.6
TYP MAX
MIN
1.6
TYP MAX
25°C
= 10 kΩ, C = 100 pF Full range
2.5
2.5
V
R
= 0.5 V to 2.5 V,
O
SR
Slew rate at unity gain
V/µs
1.1
1.1
L
L
f = 10 Hz
25°C
25°C
25°C
25°C
25°C
18
8
35
15
18
8
30
12
Equivalent input noise voltage
(see Note 5)
nV/√Hz
V
n
f = 1 kHz
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
0.5
0.7
0.6
0.5
0.7
0.6
Peak-to-peak equivalent input
noise voltage
V
I
µV
N(PP)
Equivalent input noise current
fA/√Hz
MHz
n
f = 10 kHz,
R = 10 kΩ,
L
Gain-bandwidth product
25°C
25°C
1.9
1.9
C
= 100 pF
L
L
φ
m
Phase margin at unity gain
R
= 10 kΩ, C = 100 pF
47°
47°
L
†
Full range is 0°C to +70°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ
ꢒ
ꢔ
ꢕ
ꢖ
ꢒ
ꢗ
ꢓ
ꢘ
ꢙ
ꢚ
ꢘ
ꢂ
ꢗ
ꢓ
ꢗ
ꢒ
ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201I electrical characteristics at specified free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC2201I
UNIT
†
PARAMETER
TEST CONDITIONS
T
A
MIN
TYP
MAX
500
25°C
100
V
IO
Input offset voltage
µV
Full range
650
α
Temperature coefficient of input offset voltage
Input offset voltage long-term drift (see Note 4)
Full range
25°C
0.5
µV/°C
VIO
0.001 0.005 µV/mo
V
IC
= 0,
R
= 50 Ω
S
25°C
0.5
1
60
150
60
I
I
Input offset current
Input bias current
pA
pA
IO
Full range
25°C
IB
Full range
150
−5
to
2.7
V
Common-mode input voltage range
R
R
= 50 Ω
Full range
V
ICR
S
L
25°C
Full range
25°C
4.7
4.7
−4.7
−4.7
400
250
90
4.8
−4.9
560
100
115
110
1.1
V
V
Maximum positive peak output voltage swing
Maximum negative peak output voltage swing
V
V
OM+
= 10 kΩ
OM−
Full range
25°C
V
V
=
=
4 V,
4 V,
R
R
= 500 kΩ
= 10 kΩ
O
L
L
Full range
25°C
A
VD
Large-signal differential voltage amplification
V/mV
O
Full range
25°C
65
V
V
= V
ICR
min,
90
IC
CMRR Common-mode rejection ratio
dB
dB
= 0,
R
= 50 Ω
Full range
25°C
85
O
S
90
k
Supply voltage rejection ratio (∆V
/∆V
IO
)
V
=
2.3 V to 8 V
No load
SVR
DD
DD
= 0,
Full range
25°C
85
1.5
1.5
I
Supply current
V
O
mA
DD
Full range
†
Full range is −40°C to +85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T
25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A =
TLC2201I operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2201I
†
PARAMETER
TEST CONDITIONS
T
A
UNIT
V/µs
MIN
2
TYP
MAX
R
= 10 kΩ,
25°C
Full range
25°C
2.7
V
C
=
2.3 V,
L
O
L
SR
Slew rate at unity gain
= 100 pF
1.4
f = 10 Hz
18
8
nV/√Hz
V
n
Equivalent input noise voltage
f = 1 kHz
25°C
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
25°C
0.5
0.7
0.6
V
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
µV
N(PP)
25°C
I
n
25°C
fA/√Hz
MHz
f = 10 kHz,
R
C
= 10 kΩ,
L
L
Gain-bandwidth product
25°C
25°C
1.9
C
= 100 pF
L
φ
m
Phase margin at unity gain
R
= 10 kΩ,
= 100 pF
48°
L
†
Full range is −40°C to +85°C.
18
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201I electrical characteristics at specified free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC2201AI
TLC2201BI
UNIT
†
PARAMETER
TEST CONDITIONS
T
A
MIN TYP MAX
MIN
TYP MAX
25°C
80
200
350
80
200
350
V
IO
Input offset voltage
µV
Full range
Temperature coefficient of input
offset voltage
α
VIO
Full range
0.5
0.5
µV/°C
Input offset voltage long-term
drift (see Note 4)
25°C
0.001 0.005
0.001 0.005 µV/mo
V
IC
= 0,
R
= 50 Ω
S
25°C
Full range
25°C
0.5
1
60
150
60
0.5
60
150
60
I
I
Input offset current
Input bias current
pA
IO
1
pA
V
IB
Full range
150
150
Common-mode input voltage
range
−5 to
2.7
−5 to
2.7
V
R
R
= 50 Ω
Full range
ICR
S
L
25°C
Full range
25°C
4.7
4.7
4.8
4.7
4.7
4.8
Maximum positive peak output
voltage swing
V
V
OM+
= 10 kΩ
−4.7 −4.9
−4.7
−4.7 −4.9
−4.7
Maximum negative peak output
voltage swing
V
V
OM−
Full range
25°C
400
250
90
560
100
115
110
1.1
400
250
90
560
100
115
110
1.1
V
V
=
=
4 V,
4 V,
R
R
= 500 kΩ
= 10 kΩ
O
L
L
Full range
25°C
Large-signal differential voltage
amplification
A
V/mV
VD
O
Full range
25°C
65
65
V
V
= V
ICR
min,
90
90
IC
CMRR Common-mode rejection ratio
Supply voltage rejection ratio
dB
dB
= 0,
R
= 50 Ω
Full range
25°C
85
85
O
S
90
90
k
V
DD
=
2.3 V to 8 V
No load
SVR
(∆V
DD
/∆V )
IO
Full range
25°C
85
85
1.5
1.5
1.5
1.5
I
Supply current
V
O
= 0,
mA
DD
Full range
†
Full range is −40°C to +85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150 °C extrapolated
A
to T = 25°C using the Arrhenius equation assuming an activation energy of 0.96 eV.
A
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201I operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2201AI
TLC2201BI
†
PARAMETER
TEST CONDITIONS
T
A
UNIT
MIN
2
TYP MAX
MIN
2
TYP MAX
V
=
2.3 V,
25°C
2.7
2.7
O
SR
Slew rate at unity gain
V/µs
R
= 10 kΩ,
C
= 100 pF Full range
1.4
1.4
L
L
f = 10 Hz
25°C
25°C
25°C
25°C
25°C
18
8
35
15
18
8
30
12
Equivalent input noise voltage
(see Note 5)
V
n
nV/√Hz
f = 1 kHz
f = 0.1 to 1 Hz
0.5
0.7
0.6
0.5
0.7
0.6
Peak-to-peak equivalent input
noise voltage
V
N(PP)
µV
f = 0.1 to 10 Hz
I
n
Equivalent input noise current
Gain-bandwidth product
fA/√Hz
MHz
f = 10 kHz,
R
= 10 kΩ,
25°C
L
L
1.9
1.9
C
R
= 100 pF
L
L
φ
m
Phase margin at unity gain
= 10 kΩ,
C
= 100 pF
25°C
48°
48°
†
Full range is −40°C to +85°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
20
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201I electrical characteristics at specified free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC2201I
UNIT
†
PARAMETER
TEST CONDITIONS
T
A
MIN
TYP
MAX
500
25°C
100
V
IO
Input offset voltage
µV
Full range
Full range
25°C
650
α
VIO
Temperature coefficient of input offset voltage
Input offset voltage long-term drift (see Note 4)
0.5
µV/°C
0.001 0.005 µV/mo
V
IC
= 0,
R = 50 Ω
S
25°C
0.5
60
150
60
I
I
Input offset current
Input bias current
pA
pA
IO
Full range
25°C
1
IB
Full range
150
0
to
2.7
V
Common-mode input voltage range
R
R
= 50 Ω
Full range
V
ICR
S
L
25°C
Full range
25°C
4.7
4.7
4.8
0
V
V
Maximum high-level output voltage
Maximum low-level output voltage
= 10 kΩ
V
OH
50
50
I
O
= 0
mV
OL
Full range
25°C
150
100
25
315
55
V
O
R
= 1 V to 4 V,
= 500 kΩ
Full range
25°C
L
A
VD
Large-signal differential voltage amplification
V/mV
V
R
= 1 V to 4 V,
= 10 kΩ
O
Full range
25°C
15
L
V
V
= V
min,
90
110
110
1
IC
ICR
CMRR Common-mode rejection ratio
dB
dB
= 0,
R
= 50 Ω
Full range
25°C
85
O
S
90
k
Supply voltage rejection ratio (∆V
/∆V
IO
)
V = 4.6 V to 16 V
DD
SVR
DD
Full range
25°C
85
1.5
1.5
I
Supply current
V
O
= 2.5 V,
No load
mA
DD
Full range
†
Full range is −40°C to +85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2201I operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2201I
†
PARAMETER
TEST CONDITIONS
T
A
UNIT
V/µs
MIN
1.8
TYP
MAX
V
= 0.5 V to 2.5 V,
25°C
Full range
25°C
2.5
O
SR
Slew rate at unity gain
R
= 10 kΩ,,
C
= 100 pF
1.2
L
L
f = 10 Hz
18
8
nV/√Hz
V
n
Equivalent input noise voltage
f = 1 kHz
25°C
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
25°C
0.5
0.7
0.6
V
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
µV
N(PP)
25°C
I
n
25°C
fA/√Hz
MHz
f = 10 kHz,
R
C
= 10 kΩ,
L
L
Gain-bandwidth product
25°C
25°C
1.8
C
= 100 pF
L
φ
m
Phase margin at unity gain
R
= 10 kΩ,
= 100 pF
45°
L
†
Full range is −40°C to +85°C.
21
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201I electrical characteristics at specified free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC2201AI
TLC2201BI
UNIT
†
PARAMETER
TEST CONDITIONS
T
A
MIN
TYP MAX
MIN
TYP MAX
25°C
80
200
350
80
200
350
V
IO
Input offset voltage
µA
Full range
Temperature coefficient of
input offset voltage
α
VIO
Full range
0.5
0.5
µV/°C
Input offset voltage long-term
drift (see Note 4)
25°C
0.001 0.005
0.001 0.005 µV/mo
V
IC
= 0,
R = 50 Ω
S
25°C
Full range
25°C
0.5
1
60
150
60
0.5
60
150
60
I
I
Input offset current
Input bias current
pA
pA
IO
1
IB
Full range
150
150
0
to
2.7
0
to
2.7
Common-mode input voltage
range
V
R
R
= 50 Ω
Full range
V
ICR
S
L
25°C
Full range
25°C
4.7
4.7
4.8
0
4.7
4.7
4.8
0
Maximum high-level output
voltage
V
V
= 10 kΩ
V
OH
50
50
50
50
Maximum low-level output
voltage
I
O
= 0
mV
OL
Full range
25°C
150
100
25
315
55
150
100
25
315
55
V
R
= 1 V to 4 V,
= 500 kΩ
O
Full range
25°C
L
Large-signal differential
voltage amplification
A
VD
V/mV
V
R
= 1 V to 4 V,
= 10 kΩ
O
Full range
25°C
15
15
L
V
IC
V
O
= V
min,
R
90
110
110
1
90
110
110
1
ICR
CMRR Common-mode rejection ratio
Supply voltage rejection ratio
dB
dB
= 0,
= 50 Ω
Full range
25°C
85
85
S
90
90
k
V = 4.6 V to 16 V
DD
SVR
(∆V
DD
/∆V )
IO
Full range
25°C
85
85
1.5
1.5
1.5
1.5
I
Supply current
V
O
= 2.5 V, No load
mA
DD
Full range
†
Full range is −40°C to +85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
22
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201I operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2201AI
TLC2201BI
†
PARAMETER
TEST CONDITIONS
T
A
UNIT
V/µs
MIN
1.8
TYP MAX
MIN
1.8
TYP MAX
V
= 0.5 V to 2.5 V,
25°C
2.5
2.5
O
SR
Slew rate at unity gain
R
= 10 kΩ,
C
= 100 pF Full range
1.2
1.2
L
L
f = 10 Hz
25°C
25°C
25°C
25°C
25°C
18
8
35
15
18
8
30
12
Equivalent input noise
voltage (see Note 5)
nV/√Hz
V
n
f = 1 kHz
f = 0.1 to 1 Hz
0.5
0.7
0.6
0.5
0.7
0.6
Peak-to-peak equivalent input
noise voltage
V
N(PP)
µV
f = 0.1 to 10 Hz
I
n
Equivalent input noise current
fA/√Hz
MHz
R
= 10 kΩ,
25°C
f = 10 kHz,
L
L
Gain-bandwidth product
1.8
1.8
C
= 100 pF
L
φ
m
C
= 100 pF
Phase margin at unity gain
R
= 10 kΩ,
25°C
45°
45°
L
†
Full range is −40°C to +85°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
23
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202I electrical characteristics at specified free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC2202I
UNIT
†
T
A
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
1000
1200
25°C
Full range
Full range
25°C
100
V
IO
Input offset voltage
µV
α
VIO
Temperature coefficient of input offset voltage
Input offset voltage long-term drift (see Note 4)
0.5
µV/°C
0.001 0.005 µV/mo
V
IC
= 0,
R
= 50 Ω
S
25°C
0.5
60
150
60
pA
pA
I
I
Input offset current
Input bias current
IO
Full range
25°C
1
IB
Full range
150
−5
to
2.7
V
Common-mode input voltage range
R
R
= 50 Ω
Full range
V
ICR
S
25°C
Full range
25°C
4.7
4.7
−4.7
−4.7
300
150
50
4.8
−4.9
560
100
115
110
1.8
V
V
Maximum positive peak output voltage swing
Maximum negative peak output voltage swing
OM+
V
V
= 10 kΩ
L
OM−
Full range
25°C
V
O
=
4 V,
4 V,
R
R
= 500 kΩ
= 10 kΩ
L
L
Full range
25°C
A
VD
Large-signal differential voltage amplification
V/mV
V
V
=
O
Full range
25°C
25
80
= 0,
= 50 Ω
V
IC
= V min,
ICR
O
CMRR Common-mode rejection ratio
dB
dB
R
Full range
25°C
80
S
80
k
Supply-voltage rejection ratio (∆V
/∆V
IO
)
V = 2.3 V to 8 V
DD
SVR
DD
Full range
25°C
80
2.7
2.7
I
Supply current
V
O
= 0,
No load
mA
DD
Full range
†
Full range is −40°C to +85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2202I operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2202I
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
V/µs
MIN
1.8
TYP
MAX
25°C
2.7
V
C
=
2.3 V,
R
= 10 kΩ,
O
L
L
SR
Slew rate at unity gain
= 100 pF
Full range
25°C
1.2
f = 10 Hz
18
8
nV/√Hz
V
n
Equivalent input noise voltage
f = 1 kHz
25°C
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
25°C
0.5
0.7
0.6
V
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
µV
N(PP)
25°C
I
n
25°C
fA/√Hz
MHz
f = 10 kHz,
R
C
= 10 kΩ,
L
L
Gain-bandwidth product
25°C
25°C
1.9
C
= 100 pF
L
L
φ
m
Phase margin at unity gain
R
= 10 kΩ,
= 100 pF
48°
†
Full range is −40°C to +85°C.
24
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202I electrical characteristics at specified free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC2202AI
TLC2202BI
UNIT
†
T
A
PARAMETER
TEST CONDITIONS
MIN TYP MAX
MIN
TYP MAX
25°C
80
500
700
80
500
700
V
IO
Input offset voltage
µV
Full range
Temperature coefficient
of input offset voltage
α
VIO
Full range
0.5
0.5
µV/°C
Input offset voltage long-term
drift (see Note 4)
25°C
0.001 0.005
0.001 0.005 µV/mo
V
IC
= 0,
R = 50 Ω
S
25°C
Full range
25°C
0.5
1
60
150
60
0.5
60
150
60
I
I
Input offset current
Input bias current
pA
pA
IO
1
IB
Full range
150
150
−5
to
2.7
−5
to
2.7
Common-mode input
voltage range
V
R
R
= 50 Ω
Full range
V
ICR
S
25°C
Full range
25°C
4.7
4.7
4.8
4.7
4.7
4.8
Maximum positive peak
output voltage swing
V
V
V
V
OM+
= 10 kΩ
L
−4.7 −4.9
−4.7
−4.7 −4.9
−4.7
Maximum negative peak
output voltage swing
OM−
Full range
25°C
300
150
50
560
100
115
110
1.8
300
150
50
560
100
115
110
1.8
V
R
=
4 V,
O
= 500 kΩ
Full range
25°C
L
Large-signal differential
voltage amplification
A
VD
V/mV
V
R
=
4 V,
O
= 10 kΩ
Full range
25°C
25
25
L
80
80
V
IC
V
O
= V
= 0,
min,
R
ICR
CMRR Common-mode rejection ratio
Supply-voltage rejection ratio
dB
dB
= 50 Ω
Full range
25°C
80
80
S
80
80
k
V
2.3 V to 8 V
No load
SVR
DD
= 0,
(∆V
DD
/∆V )
IO
Full range
25°C
80
80
2.7
2.7
2.7
2.7
I
Supply current
V
O
mA
DD
Full range
†
Full range is −40°C to +85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2202I operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2202AI
TLC2202BI
†
T
A
PARAMETER
TEST CONDITIONS
2.3 V, R = 10 kΩ,
UNIT
MIN
1.8
TYP MAX
MIN
1.8
TYP MAX
25°C
Full range
25°C
2.7
2.7
V
C
=
O
L
SR
Slew rate at unity gain
V/µs
= 100 pF
1.2
1.2
L
f = 10 Hz
18
8
35
15
18
8
30
12
Equivalent input noise voltage
(see Note 5)
nV/√Hz
V
n
f = 1 kHz
25°C
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
25°C
0.5
0.7
0.6
0.5
0.7
0.6
Peak-to-peak equivalent
input noise voltage
V
I
µV
N(PP)
25°C
Equivalent input noise current
25°C
fA/√Hz
MHz
n
f = 10 kHz,
R = 10 kΩ,
L
Gain-bandwidth product
25°C
25°C
1.9
1.9
C
= 100 pF
L
L
φ
m
Phase margin at unity gain
R
= 10 kΩ, C = 100 pF
48°
48°
L
†
Full range is −40°C to +85°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
25
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202I electrical characteristics at specified free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC2202I
UNIT
†
T
A
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
1000
1200
25°C
100
V
IO
Input offset voltage
µV
Full range
Full range
25°C
α
VIO
Temperature coefficient of input offset voltage
Input offset voltage long-term drift (see Note 4)
0.5
µV/°C
0.001 0.005 µV/mo
V
IC
= 0,
R
= 50 Ω
S
25°C
0.5
60
150
60
pA
pA
I
I
Input offset current
Input bias current
IO
Full range
25°C
1
IB
Full range
150
0
to
2.7
V
Common-mode input voltage range
R
R
= 50 Ω
Full range
V
ICR
S
L
25°C
Full range
25°C
4.7
4.7
4.8
0
V
V
Maximum high-level output voltage
Maximum low-level output voltage
= 10 kΩ
V
OH
50
50
I
O
= 0
mV
OL
Full range
25°C
150
100
25
315
55
V
O
R
=1 V to 4 V,
= 500 kΩ
Full range
25°C
L
A
VD
Large-signal differential voltage amplification
V/mV
V
R
= 1 V to 4 V,
= 10 kΩ
O
Full range
25°C
15
L
75
110
110
1.7
V
R
= 0,
= 50 Ω
V
= V min,
ICR
O
IC
CMRR Common-mode rejection ratio
dB
dB
Full range
25°C
75
S
80
k
Supply-voltage rejection ratio (∆V
/∆V
IO
)
V = 4.6 V to 16 V
DD
SVR
DD
Full range
25°C
80
2.6
2.6
I
Supply current
V
O
= 2.5 V,
No load
mA
DD
Full range
†
Full range is −40°C to +85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2202I operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2202I
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
V/µs
MIN
1.6
1
TYP
MAX
25°C
2.5
V
R
= 0.5 V to 2.5 V,
O
L
SR
Slew rate at unity gain
= 10 kΩ,
C
= 100 pF
L
Full range
25°C
f = 10 Hz
18
8
nV/√Hz
V
n
Equivalent input noise voltage
f = 1 kHz
25°C
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
25°C
0.5
0.7
0.6
V
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
µV
N(PP)
25°C
I
n
25°C
fA/√Hz
MHz
f = 10 kHz,
R
C
= 10 kΩ,
L
L
Gain-bandwidth product
25°C
25°C
1.9
C
= 100 pF
L
L
φ
m
Phase margin at unity gain
R
= 10 kΩ,
= 100 pF
47°
†
Full range is −40°C to +85°C.
26
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202I electrical characteristics at specified free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC2202AI
TLC2202BI
UNIT
†
T
A
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
MIN
TYP MAX
25°C
80
500
700
80
500
700
V
IO
Input offset voltage
µV
Full range
Temperature coefficient of
input offset voltage
α
VIO
Full range
0.5
0.5
µV/°C
Input offset voltage long-term
drift (see Note 4)
25°C
0.001 0.005
0.001 0.005 µV/mo
V
IC
= 0,
R = 50 Ω
S
25°C
Full range
25°C
0.5
1
60
150
60
0.5
60
150
60
I
I
Input offset current
Input bias current
pA
pA
IO
1
IB
Full range
150
150
0
to
2.7
0
to
2.7
Common-mode input
voltage range
V
R
R
= 50 Ω
Full range
V
ICR
S
L
25°C
Full range
25°C
4.7
4.7
4.8
0
4.7
4.7
4.8
0
Maximum high-level output
voltage
V
V
= 10 kΩ
V
OH
50
50
50
50
Maximum low-level output
voltage
I
O
= 0
mV
OL
Full range
25°C
150
100
25
315
55
150
100
25
315
55
V
R
= 1 V to 4 V,
= 500 kΩ
O
Full range
25°C
L
Large-signal differential
voltage amplification
A
VD
V/mV
V
R
=1 V to 4 V,
= 10 kΩ
O
Full range
25°C
15
15
L
75
110
110
1.7
75
110
110
1.7
V
IC
V
O
= V
= 0,
min,
R
ICR
CMRR Common-mode rejection ratio
Supply-voltage rejection ratio
dB
dB
= 50 Ω
Full range
25°C
75
75
S
80
80
k
V = 4.6 V to 16 V
DD
SVR
(∆V
DD
/∆V )
IO
Full range
25°C
80
80
2.6
2.6
2.6
2.6
I
Supply current
V
O
= 2.5 V, No load
mA
DD
Full range
†
Full range is −40°C to +85°C
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2202I operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2202AI
TLC2202BI
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
MIN
1.6
1
TYP MAX
MIN
1.6
1
TYP MAX
25°C
= 10 kΩ, C = 100 pF Full range
2.5
2.5
V
R
= 0.5 V to 2.5 V,
O
SR
Slew rate at unity gain
V/µs
L
L
f = 10 Hz
25°C
25°C
25°C
25°C
25°C
18
8
35
15
18
8
30
12
Equivalent input noise voltage
(see Note 5)
nV/√Hz
V
n
f = 1 kHz
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
0.5
0.7
0.6
0.5
0.7
0.6
Peak-to-peak equivalent
input noise voltage
V
I
µV
N(PP)
Equivalent input noise current
fA/√Hz
MHz
n
f = 10 kHz,
R = 10 kΩ,
L
Gain-bandwidth product
25°C
25°C
1.9
1.9
C
= 100 pF
L
L
φ
m
Phase margin at unity gain
R
= 10 kΩ, C = 100 pF
47°
47°
L
†
Full range is −40°C to +85°C
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
27
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201M electrical characteristics at specified free-air temperature, V
otherwise noted)
=
5 V (unless
DD
TLC2201M
TYP
†
PARAMETER
TEST CONDITIONS
T
A
UNIT
MAX
MIN
25°C
Full range
Full range
25°C
100
500
V
Input offset voltage
µV
IO
700
α
VIO
Temperature coefficient of input offset voltage
Input offset voltage long-term drift (see Note 4)
0.5
0.001
0.5
µV/°C
0.005 µV/mo
60
V
IC
= 0,
R
= 50 Ω
S
25°C
I
I
Input offset current
Input bias current
pA
IO
Full range
25°C
500
1
60
pA
IB
Full range
500
−5
to
2.7
V
Common-mode input voltage range
R
R
= 50 Ω
Full range
V
ICR
S
L
25°C
Full range
25°C
4.7
4.7
−4.7
−4.7
400
200
90
4.8
−4.9
560
100
115
110
1.1
V
V
Maximum positive peak output voltage swing
Maximum negative peak output voltage swing
V
V
OM+
= 10 kΩ
OM−
Full range
25°C
V
V
=
=
4 V,
4 V,
R
R
= 500 kΩ
= 10 kΩ
O
L
L
Full range
25°C
A
VD
Large-signal differential voltage amplification
V/mV
O
Full range
25°C
45
V
V
= V
ICR
min,
90
IC
CMRR Common-mode rejection ratio
dB
dB
= 0,
R
= 50 Ω
Full range
25°C
85
O
S
90
k
Supply voltage rejection ratio (∆V
/∆V
IO
)
V
=
2.3 V to 8 V
No load
SVR
DD
DD
= 0,
Full range
25°C
85
1.5
mA
1.5
I
Supply current
V
O
DD
Full range
†
Full range is −55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2201M operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2201M
†
PARAMETER
TEST CONDITIONS
T
A
UNIT
V/µs
MIN
TYP
MAX
V
C
=
2.3 V,
R
= 10 kΩ,
25°C
Full range
25°C
2
2.7
O
L
L
SR
Slew rate at unity gain
= 100 pF
1.3
f = 10 Hz
18
8
nV/√Hz
V
n
Equivalent input noise voltage
f = 1 kHz
25°C
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
25°C
0.5
0.7
0.6
V
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
µV
N(PP)
25°C
I
n
25°C
fA/√Hz
MHz
f = 10 kHz,
R
C
= 10 kΩ,
L
L
Gain-bandwidth product
Phase margin
25°C
25°C
1.9
C
= 100 pF
L
φ
m
R
= 10 kΩ,
= 100 pF
48°
L
†
Full range is −55°C to 125°C.
28
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201M electrical characteristics at specified free-air temperature, V
otherwise noted)
=
5 V (unless
DD
TLC2201AM
TLC2201BM
†
PARAMETER
TEST CONDITIONS
T
UNIT
µV
A
MIN
TYP
MAX
200
MIN
TYP
MAX
200
25°C
80
80
V
IO
Input offset voltage
Full range
400
400
Temperature coefficient of
input offset voltage
α
VIO
Full range
0.5
0.5
µV/°C
Input offset voltage
long-term drift (see Note 4)
25°C
0.001 0.005
0.001 0.005 µV/mo
V
IC
= 0,
R
= 50 Ω
S
25°C
Full range
25°C
0.5
1
60
500
60
0.5
60
500
60
I
I
Input offset current
Input bias current
pA
pA
IO
1
IB
Full range
500
500
−5
to
2.7
−5
to
2.7
Common-mode input
voltage range
V
R
R
= 50 Ω
Full range
V
ICR
S
25°C
Full range
25°C
4.7
4.7
−4.7
−4.7
400
200
90
4.8
−4.9
560
100
115
110
1.1
4.7
4.7
−4.7
−4.7
400
200
90
4.8
−4.9
560
100
115
110
1.1
Maximum positive peak
output voltage swing
V
V
V
V
OM+
= 10 kΩ
L
Maximum negative peak
output voltage swing
OM−
Full range
25°C
V
R
=
4 V,
O
= 500 kΩ
Full range
25°C
L
Large-signal differential
voltage amplification
A
VD
V/mV
V
R
=
4 V,
O
= 10 kΩ
Full range
25°C
45
45
L
V
V
= V
ICR
min,
R
90
90
Common-mode rejection
ratio
IC
CMRR
dB
dB
= 0,
= 50 Ω Full range
25°C
85
85
O
S
90
90
Supply voltage rejection
k
V
=
2.3 V to 8 V
SVR
DD
= 0,
ratio (∆V
DD
/∆V )
IO
Full range
25°C
85
85
1.5
1.5
1.5
1.5
I
Supply current
V
O
No load
mA
DD
Full range
†
Full range is −55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observable through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
29
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201M operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2201AM
TLC2201BM
TEST
CONDITIONS
†
PARAMETER
T
UNIT
V/µs
A
MIN
TYP
MAX
MIN
TYP
MAX
V
R
C
= 2.3 V,
= 10 kΩ,
= 100 pF
O
L
L
25°C
2
2.7
2
2.7
SR
Slew rate at unity gain
Full range
1.3
1.3
f = 10 Hz
25°C
25°C
25°C
25°C
25°C
18
8
35
15
18
8
30
12
Equivalent input noise voltage
(see Note 5)
nV/√Hz
V
n
f = 1 kHz
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
0.5
0.7
0.6
0.5
0.7
0.6
Peak-to-peak equivalent input
noise voltage
V
I
µV
N(PP)
Equivalent input noise current
fA/√Hz
n
f = 10 kHz,
R
C
= 10 kΩ,
Gain-bandwidth product
25°C
25°C
1.9
1.9
MHz
L
L
= 100 pF
R
C
= 10 kΩ,
= 100 pF
L
L
φ
m
Phase margin at unity gain
48°
48°
†
Full range is −55°C to 125°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
30
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201M electrical characteristics at specified free-air temperature, V = 5 V (unless otherwise
DD
noted)
TLC2201M
†
PARAMETER
TEST CONDITIONS
T
A
UNIT
MIN
TYP
MAX
500
25°C
Full range
Full range
25°C
100
V
IO
Input offset voltage
µV
700
α
VIO
Temperature coefficient of input offset voltage
Input offset voltage long-term drift (see Note 4)
0.5
µV/°C
0.001 0.005* µV/mo
V
IC
= 0,
R = 50 Ω
S
25°C
0.5
60
500
60
I
I
Input offset current
Input bias current
pA
pA
IO
Full range
25°C
1
IB
Full range
500
0
to
2.7
V
Common-mode input voltage range
R
R
= 50 Ω
Full range
V
ICR
S
L
25°C
Full range
25°C
4.7
4.7
4.8
0
V
V
Maximum high-level output voltage
Maximum low-level output voltage
= 10 kΩ
V
OH
50
50
I
O
= 0
mV
OL
Full range
25°C
150
75
25
10
90
85
90
85
315
55
V
R
= 1 V to 4 V,
= 500 kΩ
O
Full range
25°C
L
A
VD
Large-signal differential voltage amplification
V/mV
V
R
= 1 V to 4 V,
= 10 kΩ
O
Full range
25°C
L
V
V
= V
min,
110
110
1
IC
ICR
CMRR Common-mode rejection ratio
dB
dB
= 0,
R
= 50 Ω
Full range
25°C
O
S
k
Supply voltage rejection ratio (∆V
/∆V
IO
)
V = 4.6 V to 16 V
DD
SVR
DD
Full range
25°C
1.5
1.5
I
Supply current
V
O
= 2.5 V, No load
mA
DD
Full range
∗
On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
†
Full range is −55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2201M operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2201M
†
PARAMETER
TEST CONDITIONS
T
A
UNIT
V/µs
MIN
1.8
TYP
MAX
V
= 0.5 V to 2.5 V,
25°C
Full range
25°C
2.5
O
SR
Slew rate at unity gain
R
= 10 kΩ,
C
= 100 pF
1.1
L
L
f = 10 Hz
18
8
nV/√Hz
V
n
Equivalent input noise voltage
f = 1 kHz
25°C
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
25°C
0.5
0.7
0.6
V
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
µV
N(PP)
25°C
I
n
25°C
fA/√Hz
MHz
f = 10 kHz,
R
C
= 10 kΩ,
L
L
Gain-bandwidth product
25°C
25°C
1.8
C
= 100 pF
L
φ
m
Phase margin at unity gain
R
= 10 kΩ,
= 100 pF
45°
L
†
Full range is −55°C to 125°C.
31
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201M electrical characteristics at specified free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC2201AM
TLC2201BM
UNIT
†
PARAMETER
TEST CONDITIONS
T
A
MIN
TYP
MAX
MIN
TYP
MAX
200
25°C
80
200
400
80
V
IO
Input offset voltage
µV
Full range
400
Temperature coefficient of
input offset voltage
α
VIO
Full range
0.5
0.5
µV/°C
Input offset voltage
long-term drift (see Note 4)
25°C
0.001 0.005
0.001 0.005 µV/mo
V
IC
= 0,
R = 50 Ω
S
25°C
Full range
25°C
0.5
1
60
500
60
0.5
60
500
60
I
I
Input offset current
Input bias current
pA
pA
IO
1
IB
Full range
500
500
0
to
2.7
0
to
2.7
Common-mode input
voltage range
V
R
R
= 50 Ω
Full range
V
ICR
S
L
25°C
Full range
25°C
4.7
4.7
4.8
0
4.7
4.7
4.8
0
Maximum high-level output
voltage
V
V
= 10 kΩ
V
V
OH
50
50
50
50
Maximum low-level output
voltage
I
O
= 0
OL
Full range
25°C
150
75
25
10
90
85
90
85
315
55
150
75
25
10
90
85
90
85
315
55
V
R
= 1 V to 4 V,
= 500 kΩ
O
Full range
25°C
L
Large-signal differential
voltage amplification
A
VD
V/mV
V
R
= 1 V to 4 V,
= 10 kΩ
O
Full range
25°C
L
V
V
= V
ICR
min,
R
110
110
1.1
110
110
1.1
Common-mode rejection
ratio
IC
CMRR
dB
dB
= 0,
= 50 Ω Full range
25°C
O
S
Supply voltage rejection
k
V = 4.6 V to 16 V
DD
SVR
ratio (∆V
DD
/∆V )
IO
Full range
25°C
1.5
1.5
1.5
1.5
I
Supply current
V
O
= 2.5 V, No load
mA
DD
Full range
†
Full range is −55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observable through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
32
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201M operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2201AM
TLC2201BM
†
PARAMETER
TEST CONDITIONS
T
UNIT
V/µs
A
MIN
TYP
MAX
MIN
TYP
MAX
V
O
= 0.5 V to 2.5 V,
= 10 kΩ,
25°C
1.8
2.5
1.8
1.1
2.5
R
C
SR
Slew rate at unity gain
L
L
Full range
1.1
= 100 pF
f = 10 Hz
25°C
25°C
25°C
25°C
25°C
18
8
35
15
18
8
30
12
Equivalent input noise voltage
(see Note 5)
nV/√Hz
V
n
f = 1 kHz
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
0.5
0.7
0.6
0.5
0.7
0.6
Peak-to-peak equivalent input
noise voltage
V
I
µV
N(PP)
Equivalent input noise current
fA/√Hz
n
f = 10 kHz,
R
C
= 10 kΩ,
Gain-bandwidth product
25°C
25°C
1.8
1.8
MHz
L
L
= 100 pF
R
C
= 10 kΩ,
= 100 pF
L
L
φ
m
Phase margin at unity gain
45°
45°
†
Full range is −55°C to 125°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
33
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202M electrical characteristics at specified free-air temperature, V
otherwise noted)
=
5 V (unless
DD
TLC2202M
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
MAX
MIN
TYP
25°C
Full range
Full range
25°C
100
1000
V
Input offset voltage
µV
IO
1250
α
VIO
Temperature coefficient of input offset voltage
Input offset voltage long-term drift (see Note 4)
0.5
µV/°C
0.001 0.005 µV/mo
V
IC
= 0,
R
= 50 Ω
S
25°C
0.5
60
500
60
pA
pA
I
I
Input offset current
Input bias current
IO
Full range
25°C
1
IB
Full range
500
−5
to
2.7
V
Common-mode input voltage range
R
R
= 50 Ω
Full range
V
ICR
S
25°C
Full range
25°C
4.7
4.7
−4.7
−4.7
300
100
50
4.8
−4.9
560
100
115
110
1.8
V
V
Maximum positive peak output voltage swing
Maximum negative peak output voltage swing
OM+
V
V
= 10 kΩ
L
OM−
Full range
25°C
V
R
=1 V to 4 V,
= 500 kΩ
O
Full range
25°C
L
A
VD
Large-signal differential voltage amplification
V/mV
V
R
= 1 V to 4 V,
= 10 kΩ
O
Full range
25°C
25
L
80
V
R
= 0,
= 50 Ω
V
= V min,
ICR
O
IC
CMRR Common-mode rejection ratio
dB
dB
Full range
25°C
80
S
80
k
Supply-voltage rejection ratio (∆V
/∆V
IO
)
V = 2.3 V to 8 V
DD
SVR
DD
Full range
25°C
80
2.7
2.7
I
Supply current
V
O
= 0,
No load
mA
DD
Full range
*On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
†
Full range is −55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2202M operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2202M
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
V/µs
MIN
TYP
MAX
25°C
Full range
25°C
1.8
1.1
2.7
V
C
=
2.3 V,
R
= 10 kΩ,
O
L
L
SR
Slew rate at unity gain
= 100 pF
f = 10 Hz
18
8
nV/√Hz
V
n
Equivalent input noise voltage
f = 1 kHz
25°C
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
25°C
0.5
0.7
0.6
V
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
µV
N(PP)
25°C
I
n
25°C
fA/√Hz
MHz
f = 10 kHz,
R
C
= 10 kΩ,
L
L
Gain-bandwidth product
25°C
25°C
1.9
C
= 100 pF
L
L
φ
m
Phase margin at unity gain
R
= 10 kΩ,
= 100 pF
48°
†
Full range is −55°C to 125°C.
34
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202M electrical characteristics at specified free-air temperature, V
otherwise noted)
=
5 V (unless
DD
TLC2202AM
TLC2202BM
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
µV
MIN
TYP
MAX
500
MIN
TYP
MAX
500
25°C
80
80
V
IO
Input offset voltage
Full range
750
750
Temperature coefficient
of input offset voltage
α
VIO
Full range
0.5
0.5
µV/°C
Input offset voltage
long-term drift (see Note 4)
25°C
0.001 0.005*
0.001 0.005* µV/mo
V
IC
= 0,
R = 50 Ω
S
25°C
Full range
25°C
0.5
1
60
500
60
0.5
60
500
60
I
I
Input offset current
Input bias current
pA
pA
IO
1
IB
Full range
500
500
−5
to
2.7
−5
to
2.7
Common-mode input
voltage range
V
R
R
= 50 Ω
Full range
V
ICR
S
25°C
Full range
25°C
4.7
4.7
4.8
−4.9
560
4.7
4.7
4.8
−4.9
560
Maximum positive peak
output voltage swing
V
V
V
V
OM+
= 10 kΩ
L
−4.7
−4.7
300
100
−4.7
−4.7
300
100
Maximum negative peak
output voltage swing
OM−
Full range
25°C
V
R
=
4 V,
O
= 500 kΩ
Full range
L
Large-signal differential
voltage amplification
A
VD
V/mV
25°C
Full range
25°C
50
25
80
80
80
80
100
115
110
1.8
50
25
80
80
80
80
100
115
110
1.8
V
R
=
4 V,
O
= 10 kΩ
L
Common-mode rejection
ratio
V
R
= 0,
V
= V min,
ICR
O
IC
CMRR
dB
dB
= 50 Ω
Full range
25°C
S
Supply-voltage rejection
k
V
DD
=
2.3 V to 8 V
SVR
ratio (∆V
DD
/∆V )
IO
Full range
25°C
Full range
2.7
2.7
2.7
2.7
I
Supply current
V
O
= 0,
No load
mA
DD
*On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
†
Full range is −55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
35
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202M operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2202AM
TLC2202BM
†
PARAMETER
TEST CONDITIONS
2.3 V,
T
UNIT
V/µs
A
MIN
1.8
TYP
MAX
MIN
TYP
MAX
V
O
=
25°C
2.7
1.8
1.1
2.7
R
C
= 10 kΩ,
= 100 pF
SR
Slew rate at unity gain
L
L
Full range
1.1
f = 10 Hz
25°C
25°C
25°C
25°C
25°C
18
8
35*
15*
18
8
30*
12*
Equivalent input noise voltage
(see Note 5)
nV/√Hz
V
n
f = 1 kHz
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
0.5
0.7
0.6
0.5
0.7
0.6
Peak-to-peak equivalent input
noise voltage
V
I
µV
N(PP)
Equivalent input noise current
fA/√Hz
n
f = 10 kHz,
R
C
= 10 kΩ,
= 100 pF
Gain-bandwidth product
25°C
1.9
1.9
MHz
L
L
R
C
= 10 kΩ,
= 100 pF
L
L
φ
m
Phase margin at unity gain
25°C
48°
48°
*On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
†
Full range is −55°C to 125°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
36
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202M electrical characteristics at specified free-air temperatures, V
noted)
= 5 V (unless otherwise
DD
TLC2202M
UNIT
†
T
A
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
1000
1250
25°C
Full range
Full range
25°C
100
V
IO
Input offset voltage
µV
α
VIO
Temperature coefficient of input offset voltage
Input offset voltage long-term drift (see Note 4)
0.5
µV/°C
0.001 0.005* µV/mo
V
IC
= 0,
R = 50 Ω
S
25°C
0.5
60
500
60
pA
pA
I
I
Input offset current
Input bias current
IO
Full range
25°C
1
IB
Full range
500
0
to
2.7
V
Common-mode input voltage range
R
R
= 50 Ω
Full range
V
ICR
S
L
25°C
Full range
25°C
4.7
4.7
4.8
0
V
V
Maximum high-level output voltage
Maximum low-level output voltage
= 10 kΩ
V
OH
50
50
I
O
= 0
mV
OL
Full range
25°C
150
75
25
10
75
75
80
80
315
55
V
O
R
= 1 V to 4 V,
= 500 kΩ
Full range
25°C
L
A
VD
Large-signal differential voltage amplification
V/mV
V
R
= 1 V to 4 V,
= 10 kΩ
O
Full range
25°C
L
110
110
1.7
CMRR Common-mode rejection ratio
V
V
V
= V
ICR
min,
R
= 50 Ω
S
dB
dB
IC
Full range
25°C
k
Supply-voltage rejection ratio (∆V
/∆V
IO
)
= 4.6 V to 16 V
DD
SVR
DD
Full range
25°C
2.6
2.6
I
Supply current
= 2.5 V,
No load
mA
DD
O
Full range
*On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
†
Full range is −55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2202M operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2202M
†
T
A
PARAMETER
TEST CONDITIONS
UNIT
V/µs
MIN
1.6
TYP
MAX
25°C
Full range
25°C
2.5
V
R
= 0.5 V to 2.5 V,
O
L
SR
Slew rate at unity gain
= 10 kΩ,
C
= 100 pF
0.9
L
f = 10 Hz
18
8
nV/√Hz
V
n
Equivalent input noise voltage
f = 1 kHz
25°C
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
25°C
0.5
0.7
0.6
V
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
µV
N(PP)
25°C
I
n
25°C
fA/√Hz
MHz
f = 10 kHz,
R
C
= 10 kΩ,
L
L
Gain-bandwidth product
25°C
25°C
1.9
C
= 100 pF
L
L
φ
m
Phase margin at unity gain
R
= 10 kΩ,
= 100 pF
47°
†
Full range is −55°C to 125°C.
37
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202M electrical characteristics at specified free-air temperature, V
noted)
= 5 V (unless otherwise
DD
TLC2202AM
TLC2202BM
UNIT
†
PARAMETER
TEST CONDITIONS
T
A
MIN
TYP
MAX
MIN
TYP
MAX
500
25°C
80
500
750
80
V
IO
Input offset voltage
µV
Full range
750
Temperature coefficient of
input offset voltage
α
VIO
Full range
0.5
0.5
µV/°C
Input offset voltage
long-term drift (see Note 4)
25°C
0.001 0.005*
0.001 0.005* µV/mo
V
IC
= 0,
R = 50 Ω
S
25°C
Full range
25°C
0.5
1
60
500
60
0.5
60
500
60
I
I
Input offset current
Input bias current
pA
pA
IO
1
IB
Full range
500
500
0
to
2.7
0
to
2.7
Common-mode input
voltage range
V
R
R
= 50 Ω
Full range
V
ICR
S
L
25°C
Full range
25°C
4.7
4.7
4.8
0
4.7
4.7
4.8
0
Maximum high-level output
voltage
V
V
= 10 kΩ
V
OH
50
50
50
50
Maximum low-level output
voltage
I
O
= 0
mV
OL
Full range
25°C
150
75
25
10
75
75
80
80
315
55
150
75
25
10
75
75
80
80
315
55
V
R
= 1 V to 4 V,
= 500 kΩ
O
Full range
25°C
L
Large-signal differential
voltage amplification
A
VD
V/mV
V
R
= 1 V to 4 V,
= 10 kΩ
O
Full range
25°C
L
110
110
1.7
110
110
1.7
Common-mode rejection
ratio
V
R
= 0,
V
= V min,
ICR
O
IC
CMRR
dB
dB
= 50 Ω
Full range
25°C
S
Supply-voltage rejection
k
V = 4.6 V to 16 V
DD
SVR
ratio (∆V
DD
/∆V )
IO
Full range
25°C
2.6
2.6
2.6
2.6
I
Supply current
V
O
= 2.5 V, No load
mA
DD
Full range
*On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
†
Full range is −55°C to 125°C
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
38
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202M operating characteristics at specified free-air temperature, V
= 5 V
DD
TLC2202AM
TLC2202BM
†
PARAMETER
TEST CONDITIONS
T
UNIT
V/µs
A
MIN
1.6
TYP
MAX
MIN
1.6
TYP
MAX
V
R
C
= 0.5 V to 2.5 V,
= 10 kΩ,
O
L
L
25°C
2.5
2.5
SR
Slew rate at unity gain
Full range
0.9
1.1
= 100 pF
f = 10 Hz
25°C
25°C
25°C
25°C
25°C
18
8
35*
15*
18
8
30*
12*
Equivalent input noise voltage
(see Note 5)
nV/√Hz
V
n
f = 1 kHz
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
0.5
0.7
0.6
0.5
0.7
0.6
Peak-to-peak equivalent input
noise voltage
V
I
µV
N(PP)
Equivalent input noise current
fA/√Hz
n
f = 10 kHz,
R
C
= 10 kΩ,
= 100 pF
Gain-bandwidth product
25°C
1.9
1.9
MHz
L
L
R
C
= 10 kΩ,
= 100 pF
L
L
φ
m
Phase margin at unity gain
25°C
47°
47°
*On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
†
Full range is −55°C to 125°C
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
39
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2201Y electrical characteristics at V
= 5 V, T = 25°C (unless otherwise noted)
DD
A
TLC2201Y
PARAMETER
TEST CONDITIONS
UNIT
MIN
TYP
100
0.001
0.5
1
MAX
V
IO
Input offset voltage
µV
µV/mo
pA
Input offset voltage long-term drift (see Note 4)
Input offset current
V
IC
= 0,
R
= 50 Ω
S
I
I
IO
Input bias current
pA
IB
V
V
Maximum high-level output voltage
Maximum low-level output voltage
R
= 10 kΩ
4.8
0
V
OH
L
I
O
= 0
mV
OL
V
V
V
= 1 V to 4 V,
= 1 V to 4 V,
R
R
= 500 Ω
= 10 Ω
= 0,
55
O
O
IC
L
L
A
Large-signal differential voltage amplification
V/mV
dB
VD
55
= V
ICR
min,
V
O
CMRR Common-mode rejection ratio
110
R
= 50 Ω
S
k
Supply voltage rejection ratio (∆V
/∆V
IO
)
V
V
= 4.6 to 16 V
110
1
dB
SVR
DD
DD
I
Supply current per amplifier
= 2.5 V,
No load
mA
DD
O
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2201Y operating characteristics at V
=
5 V, T = 25°C
DD
A
TLC2201Y
TYP
2.5
PARAMETER
TEST CONDITIONS
UNIT
MIN
MAX
SR
Positive slew rate at unity gain
Equivalent input noise voltage
V
=
0.5 to 2.5 V,
R
= 10 kΩ,
C = 100 pF
L
V/µs
O
L
f = 10 Hz
18
nV/√Hz
µV
V
n
f = 1 kHz
8
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
0.5
Peak-to-peak equivalent input noise
voltage
V
N(PP)
0.7
I
Equivalent input noise current
Gain-bandwidth product
0.6
pA/√Hz
n
f = 10 kHz,
R
C
= 10 kΩ,
C
= 100 pF
L
1.8
MHz
L
L
φ
Phase margin at unity gain
R
= 10 kΩ,
L
= 100 pF
48°
m
40
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TLC2202Y electrical characteristics, V
= 5 V, T = 25°C (unless otherwise noted)
A
DD
TLC2202Y
PARAMETER
TEST CONDITIONS
UNIT
MIN
TYP
100
0.001
0.5
1
MAX
V
IO
Input offset voltage
µV
µV/mo
pA
Input offset voltage long-term drift (see Note 4)
Input offset current
V
IC
= 0,
R
= 50 Ω
S
I
I
IO
Input bias current
pA
IB
V
V
Maximum high-level output voltage
Maximum low-level output voltage
R
= 10 kΩ
4.8
0
V
OH
L
I
O
= 0
mV
OL
V
V
V
V
V
= 1 V to 4 V,
= 1 V to 4 V,
R
R
R
= 500 Ω
= 10 Ω
= 50 Ω
315
55
O
L
L
S
A
Large-signal differential voltage amplification
V/mV
VD
O
CMRR Common-mode rejection ratio
= 0, V
min,
= 4.6 to 16 V
110
110
1.7
dB
dB
O
ICR
k
Supply-voltage rejection ratio (∆V
/∆V )
IO
SVR
DCC
DD
I
Supply current
= 2.5 V,
No load
mA
DD
O
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
TLC2202Y operating characteristics at V
= 5 V, T = 25°C
A
DD
TLC2202Y
TYP
PARAMETER
TEST CONDITIONS
UNIT
MIN
MAX
V
C
= 0.5 V to 2.5 V,
= 100 pF
R
= 10 kΩ,
O
L
L
SR
Positive slew rate at unity gain
Equivalent input noise voltage
2.5
V/µs
f = 10 Hz
18
8
nV/√Hz
V
n
f = 10 kHz
f = 0.1 to 1 Hz
f = 0.1 to 10 Hz
0.5
0.7
0.6
V
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
Gain-bandwidth product
µV
N(PP)
I
n
pA/√Hz
MHz
f = 10 kHz,
R
C
= 10 kΩ,
L
L
B
1
1.9
C
= 100 pF
L
L
φ
m
Phase margin at unity gain
R
= 10 kΩ,
= 100 pF
47°
41
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
PARAMETER MEASUREMENT INFORMATION
10 kΩ
V
DD +
2 kΩ
V
I
−
+
V
O
100 Ω
V
DD +
V
DD −
−
+
V
O
C
R
L
L
(see Note A)
V
/GND
DD−
20 Ω
20 Ω
NOTE A: C includes fixture capacitance.
L
Figure 1. Noise-Voltage Test Circuit
Figure 2. Phase-Margin Test Circuit
V
DD+
−
+
V
O
V
DD+
V
I
Ground Shield
V
DD−
−
+
V
O
C
R
L
L
(see Note A)
V
DD−
/GND
pA
pA
NOTE A: C includes fixture capacitance.
L
Figure 3. Slew-Rate Test Circuit
Figure 4. Input-Bias and Offset-Current Test Circuit
typical values
Typical values presented in this data sheet represent the median (50% point) of device parametric performance.
input bias and offset current
At the picoamp bias current level of the TLC220x, TLC220xA, and TLC220xB, accurate measurement of the
bias current becomes difficult. Not only does this measurement require a picoammeter, but test socket leakages
can easily exceed the actual device bias currents. To measure these small currents, Texas Instruments uses
a two-step process. The socket leakage is measured using picoammeters with bias voltages applied but with
no device in the socket. The device is then inserted in the socket, and a second test measuring both the socket
leakage and the device input bias current is performed. The two measurements are then subtracted
algebraically to determine the bias current of the device.
noise
Texas Instruments offers automated production noise testing to meet individual application requirements. Noise
voltage at f = 10 Hz and f = 1 kHz is 100% tested on every TLC2201B device, while lot sample testing is
performed on the TLC220xA. For other noise requirements, please contact the factory.
42
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
V
Input offset voltage
Input bias current
Distribution
5, 6
IO
vs Common-mode input voltage
vs Free-air temperature
7
8
I
IB
vs Output current
vs Free-air temperature
9
10
V
V
Maximum peak output voltage
OM
Maximum peak-to-peak output voltage
vs Frequency
11
O(PP)
vs Frequency
vs High-level output current
vs Free-air temperature
12
13
14
V
OH
V
OL
High-level output voltage
vs Low-level output current
vs Free-air temperature
15
16
Low-level output voltage
vs Frequency
vs Free-air temperature
17
18
A
Large-signal differential voltage amplification
Short-circuit output current
VD
OS
vs Supply voltage
vs Free-air temperature
19
20
I
CMRR Common-mode rejection ratio
vs Frequency
21
vs Supply voltage
vs Free-air temperature
22
23, 24
I
Supply current
DD
Small signal
Large signal
25, 26
27, 28
Pulse response
vs Supply voltage
vs Free-air temperature
29
30
SR
Slew rate
0.1 to 1 Hz
0.1 to 10 Hz
31
32
Noise voltage (referred to input)
Gain-bandwidth product
vs Supply voltage
vs Free-air temperature
33, 34
35
vs Supply voltage
vs Free-air temperature
36, 37
38, 39
φ
m
Phase margin
Phase shift
vs Frequency
17
43
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ
ꢒ
ꢔ
ꢕ
ꢖ
ꢒ
ꢗ
ꢓ
ꢘ
ꢙ
ꢚ
ꢘ
ꢂ
ꢗ
ꢓ
ꢗ
ꢒ
ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TYPICAL CHARACTERISTICS
TLC2202
DISTRIBUTION OF
INPUT OFFSET VOLTAGE
DISTRIBUTION OF TLC2201
INPUT OFFSET VOLTAGE
16
14
12
10
8
20
16
12
8
1726 Amplifiers Tested From 1 Wafer Lot
408 Units Tested From 2 Wafer Lots
V
T
=
5 V
V
T
=
15 V
DD
DD
A
= 25°C
= 25°C
A
P Package
P Package
6
4
4
2
0
0
−1000
200
600
1000
−600
−200
100
300
500
−500
−300
V
−100
V
IO
− Input Offset Voltage − µV
− Input Offset Voltage − µV
IO
Figure 5
Figure 6
†
INPUT BIAS CURRENT
vs
INPUT BIAS CURRENT
vs
COMMON-MODE INPUT VOLTAGE
FREE-AIR TEMPERATURE
= 5 V
= 0
= 0
10
8
300
250
200
150
100
50
V
T
=
5 V
V
V
V
DD
DD
O
IC
= 25°C
A
6
4
2
0
−2
−4
−6
−8
−10
0
−5 −4 −3 −2 −1
0
1
2
3
4
5
25
45
65
85
105
125
V
IC
− Common-Mode Input Voltage − V
T
A
− Free-Air Temperature − °C
Figure 7
Figure 8
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
44
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TYPICAL CHARACTERISTICS
†
MAXIMUM PEAK OUTPUT VOLTAGE
MAXIMUM PEAK OUTPUT VOLTAGE
vs
vs
OUTPUT CURRENT
FREE-AIR TEMPERATURE
5
4
3
6
4
V
T
A
=
5 V
DD
= 25°C
V
OM+
V
OM+
V
OM−
2
V
R
=
5 V
DD
L
0
= 10 kΩ
2
1
0
−2
−4
−6
V
OM−
0
2
4
6
8
10
−75 −50 −25
0
25
50
75 100 125
|I | − Output Current − mA
O
T
A
− Free-Air Temperature − °C
Figure 9
Figure 10
†
†
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE
HIGH-LEVEL OUTPUT VOLTAGE
vs
vs
FREQUENCY
FREQUENCY
10
5
4
3
2
1
8
6
4
2
0
T
A
= −55°C
T
A
= −55°C
T
A
= 125°C
T
A
= 125°C
V
R
=
5 V
V
R
= 5 V
= 10 kΩ
L
DD
L
DD
= 10 kΩ
0
10 k
30 k
100 k
300 k
1 M
10 k
30 k
100 k
300 k
1 M
f − Frequency − Hz
f − Frequency − Hz
Figure 11
Figure 12
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
45
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ
ꢒ
ꢔ
ꢕ
ꢖ
ꢒ
ꢗ
ꢓ
ꢘ
ꢙ
ꢚ
ꢘ
ꢂ
ꢗ
ꢓ
ꢗ
ꢒ
ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TYPICAL CHARACTERISTICS
†
HIGH-LEVEL OUTPUT VOLTAGE
HIGH-LEVEL OUTPUT VOLTAGE
vs
vs
HIGH-LEVEL OUTPUT CURRENT
FREE-AIR TEMPERATURE
V
V
V
V
V
6
5
4
3
2
1
0
DD
DD
DD
DD
DD
V
R
= 5 V
= 10 kΩ
DD
L
T
= 25°C
A
−2
−4
−6
−8
V
DD
= 5 V
V
DD
= 10 V
V
−10
−12
−14
−16
DD
DD
DD
DD
V
V
V
V
= 16 V
DD
0
1
2
3
4
5
−75 −50 −25
0
25
50
75 100 125
T
A
− Free-Air Temperature − °C
I
− High-Level Output Current − mA
OH
Figure 13
Figure 14
†
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
LOW-LEVEL OUTPUT CURRENT
1.5
2
V = 5 V
DD
V
DD
V
DD
V
DD
= 5 V
T
A
= 25°C
= 10 V
= 16 V
I
= 5 mA
OL
1.5
1
1
0.5
0.5
0
I
= 1 mA
OL
0
−75 −50 −25
0
25
50
75 100 125
0
2
4
6
8
10
T − Free-Air Temperature − °C
A
I
− Low-Level Output Current − mA
OL
Figure 15
Figure 16
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
46
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TYPICAL CHARACTERISTICS
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
†
AMPLIFICATION
vs
FREE-AIR TEMPERATURE
AMPLIFICATION AND PHASE SHIFT
vs
FREQUENCY
130
120
110
100
90
120
100
80
30°
V
R
C
= 5 V
DD
L
L
= 10 kΩ
= 100 pF
= 25°C
50°
V
= 5 V, R = 500 kΩ
L
DD
A
VD
T
A
70°
60
90°
V
= 5 V, R = 500 kΩ
L
DD
Phase Shift
V
= 5 V, R = 10 kΩ
L
DD
40
110°
130°
150°
170°
20
V
DD
= 5 V, R = 10 kΩ
L
0
80
−20
−75 −50 −25
0
25
50
75 100 125
10
100
1 k
10 k
100 k
1 M
T
A
− Free-Air Temperature − °C
f − Frequency − Hz
Figure 18
Figure 17
†
SHORT-CIRCUIT OUTPUT CURRENT
SHORT-CIRCUIT OUTPUT CURRENT
vs
vs
SUPPLY VOLTAGE
FREE-AIR TEMPERATURE
12
8
15
10
V
V
= 5 V
V
= 0
DD
= 0
O
T = 25°C
A
O
4
0
5
0
V
ID
= −100 mV
V
ID
= −100 mV
−4
−8
−12
−5
V
ID
= 100 mV
−10
−15
V
= 100 mV
6
ID
0
1
2
3
4
5
7
8
−75 −50 −25
0
25
50
75 100 125
|V
DD
| − Supply Voltage − V
T
A
− Free-Air Temperature − °C
Figure 19
Figure 20
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
47
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TYPICAL CHARACTERISTICS
†
COMMON-MODE REJECTION RATIO
SUPPLY CURRENT
vs
vs
FREQUENCY
SUPPLY VOLTAGE
120
100
80
60
40
20
0
2.5
2
V
= 0
O
T
= 25°C
A
No Load
V
= 5 V
DD
1.5
1
T
= 125°C
T
= 25°C
A
A
T
= −55°C
A
V
= 5 V
DD
0.5
0
10
100
1 k
10 k
100 k
1 M
0
1
2
3
4
5
6
7
8
f − Frequency − Hz
|V
DD
| − Supply Voltage − V
Figure 21
Figure 22
TLC2201
SUPPLY CURRENT
vs
TLC2202
SUPPLY CURRENT
vs
†
†
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
1.2
1
2.5
2
V
DD
= 5 V
V
= V
DD+
/2
O
No Load
V
DD
= 5 V
V
DD
= 5 V
0.8
0.6
0.4
0.2
0
V
DD
= 5 V
1.5
1
0.5
0
V
= V /2
DD+
O
No Load
−75 −50 −25
0
25
50
75 100 125
−75 −50 −25
0
25
50
75 100 125
T
A
− Free-Air Temperature − °C
T
A
− Free-Air Temperature − °C
Figure 23
Figure 24
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
48
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TYPICAL CHARACTERISTICS
VOLTAGE-FOLLOWER
SMALL-SIGNAL
PULSE RESPONSE
VOLTAGE-FOLLOWER
SMALL-SIGNAL
PULSE RESPONSE
100
75
160
140
120
100
80
V
= 5 V
= 10 kΩ
= 100 pF
= 25°C
V
= 5 V
DD
L
L
DD
L
L
R
C
T
R
C
T
= 10 kΩ
= 100 pF
= 25°C
A
A
50
25
0
60
−25
−50
40
20
0
−75
−20
−100
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
t − Time − µs
t − Time − µs
Figure 25
Figure 26
VOLTAGE-FOLLOWER
LARGE-SIGNAL
VOLTAGE-FOLLOWER
LARGE-SIGNAL
PULSE RESPONSE
PULSE RESPONSE
5
4
3
2
1
0
5
4
V
R
C
= 5 V
DD
L
L
= 10 kΩ
= 100 pF
= 25°C
T
A
3
2
−1
−2
−3
−4
−5
1
V
R
C
= 5 V
DD
L
L
= 10 kΩ
= 100 pF
= 25°C
0
T
A
−1
0
5
10 15 20 25 30 35 40
0
5
10 15 20 25 30 35 40
t − Time − µs
t − Time − µs
Figure 27
Figure 28
49
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TYPICAL CHARACTERISTICS
†
SLEW RATE
vs
SLEW RATE
vs
FREE-AIR TEMPERATURE
SUPPLY VOLTAGE
4
3
4
3
2
SR −
SR +
R
C
T
A
= 10 kΩ
= 100 pF
= 25°C
L
L
SR −
SR +
2
1
1
V
R
C
= 5 V
= 10 kΩ
= 100 pF
DD
L
L
0
0
−75 −50 −25
0
25
50
75 100 125
0
1
2
3
4
5
6
7
8
T
A
− Free-Air Temperature − °C
|V
DD
| − Supply Voltage − V
Figure 29
Figure 30
NOISE VOLTAGE
(REFERRED TO INPUT)
OVER A 10-SECOND INTERVAL
NOISE VOLTAGE
(REFERRED TO INPUT)
OVER A 10-SECOND INTERVAL
1
1
0.8
V
=
5 V
f= 0.1 Hz to 1 Hz
T = 25°C
DD
V
=
5 V
f= 0.1 Hz to 10 Hz
T = 25°C
DD
0.75
0.5
A
A
0.6
0.4
0.25
0
0.2
0
−0.2
−0.4
−0.6
−0.8
−1
−0.25
−0.5
−0.75
−1
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
t − Time − s
t − Time − s
Figure 31
Figure 32
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
50
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TYPICAL CHARACTERISTICS
TLC2201
GAIN-BANDWIDTH PRODUCT
TLC2202
GAIN-BANDWIDTH PRODUCT
vs
vs
SUPPLY VOLTAGE
SUPPLY VOLTAGE
2.1
2.1
R
C
T
A
= 10 kΩ
= 100 pF
= 25°C
L
L
f = 10 kHz
R
C
T
= 10 kΩ
L
L
= 100 pF
= 25°C
A
2
2
1.9
1.9
1.8
1.8
0
1
2
3
4
5
6
7
8
0
1
2
3
4
5
6
7
8
|V
DD
| − Supply Voltage − V
|V
| − Supply Voltage − V
DD
Figure 33
Figure 34
TLC2201
PHASE MARGIN
vs
†
GAIN-BANDWIDTH PRODUCT
vs
FREE-AIR TEMPERATURE
SUPPLY VOLTAGE
2.5
50°
48°
f = 10 kHz
R
C
T
= 10 kΩ
= 100 pF
= 25°C
L
L
A
R
C
= 10 kΩ
= 100 pF
L
L
V
DD
= 5 V
2
1.5
1
46°
44°
42°
40°
V
DD
= 5 V
−75 −50 −25
0
25
50
75 100 125
0
1
2
3
4
5
6
7
8
T
A
− Free-Air Temperature − °C
|V
DD
| − Supply Voltage − V
Figure 35
Figure 36
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
51
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢃ ꢄ ꢅ ꢇꢆ ꢀꢁ ꢂꢃ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢃ ꢄꢅ ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
TYPICAL CHARACTERISTICS
TLC2202
PHASE MARGIN
vs
TLC2201
PHASE MARGIN
vs
†
SUPPLY VOLTAGE
FREE-AIR TEMPERATURE
50°
48°
46°
44°
42°
40°
50°
48°
R
C
T
= 10 kΩ
= 100 pF
= 25°C
L
L
A
V
= 5 V
DD
46°
44°
42°
V
= 5 V
DD
R
C
= 10 kΩ
= 100 pF
L
L
40°
−75 −50 −25
0
1
2
3
4
5
6
7
8
0
25
50
75 100 125
|V
DD
| − Supply Voltage − V
T
A
− Free-Air Temperature − °C
Figure 37
Figure 38
TLC2202
PHASE MARGIN
vs
†
FREE-AIR TEMPERATURE
50°
48°
V
DD
= 5 V
V
DD
= 5 V
46°
44°
42°
40°
R
C
= 10 kΩ
= 100 pF
L
L
−75 −50 −25
0
25
50
75 100 125
T
A
− Free-Air Temperature − °C
Figure 39
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
52
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢇ ꢆ ꢀ ꢁꢂ ꢃ ꢃ ꢄꢅ ꢈ ꢆ ꢀꢁ ꢂꢃ ꢃꢄ ꢅꢉ
ꢍ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁ ꢒ ꢔꢕꢖꢒ ꢗꢓ ꢘ ꢙꢚ ꢘꢂ ꢗ ꢓꢗ ꢒ ꢖ
ꢒ ꢙꢘꢚ ꢇꢀ ꢗꢒ ꢖꢇꢁ ꢇꢑ ꢙ ꢁꢗ ꢛꢗ ꢘꢚ ꢓ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
APPLICATION INFORMATION
latch-up avoidance
Because CMOS devices are susceptible to latch-up due to their inherent parasitic thyristors, the TLC220x,
TLC220xA, and TLC220xB inputs and outputs are designed to withstand −100-mA surge currents without
sustaining latch-up; however, techniques reducing the chance of latch-up should be used whenever possible.
Internal protection diodes should not be forward biased in normal operation. Applied input and output voltages
should not exceed the supply voltage by more than 300 mV. Care should be exercised when using capacitive
coupling on pulse generators. Supply transients should be shunted by the use of decoupling capacitors
(0.1 µF typical) located across the supply rails as close to the device as possible.
electrostatic discharge protection
These devices use internal ESD-protection circuits that prevent functional failures at voltages at or below
2000 V. Care should be exercised in handling these devices as exposure to ESD may result in degradation of
the device parametric performance.
macromodel information
Macromodel information provided was derived using Microsim Parts, the model generation software used
with Microsim PSpice. The Boyle macromodel (see Note 5) and subcircuit in Figure 40 were generated using
the TLC220x typical electrical and operating characteristics at 25°C. Using this information, output simulations
of the following key parameters can be generated to a tolerance of 20% (in most cases):
D
D
D
D
D
D
Maximum positive output voltage swing
Maximum negative output voltage swing
Slew rate
D
D
D
D
D
D
Unity-gain frequency
Common-mode rejection ratio
Phase margin
Quiescent power dissipation
Input bias current
DC output resistance
AC output resistance
Short-circuit output current limit
Open-loop voltage amplification
NOTE 5: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Integrated Circuit Operational Amplifiers”, IEEE Journal
of Solid-State Circuits, SC-9, 353 (1974).
PSpice and Parts are trademarks of MicroSim Corporation.
53
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ
ꢁ
ꢂ
ꢃ
ꢃ
ꢄ
ꢅ
ꢆ
ꢀ
ꢁ
ꢂ
ꢃ
ꢃ
ꢄ
ꢅ
ꢇ
ꢆ
ꢀ
ꢁ
ꢂ
ꢃ
ꢃ
ꢄ
ꢅ
ꢈ
ꢆ
ꢀ
ꢁ
ꢂ
ꢃ
ꢃ
ꢄ
ꢅ
ꢉ
ꢇ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢊ
ꢁ
ꢐ
ꢍ
ꢒꢙ ꢘ ꢚꢇꢀ ꢗ ꢒꢖ ꢇ ꢁ ꢇꢑ ꢙꢁ ꢗ ꢛꢗ ꢘ ꢚꢓ
ꢂ
ꢑ
ꢒ
ꢓ
ꢁꢒ ꢔꢕꢖꢒ ꢗ ꢓ ꢘ ꢙ ꢚꢘ ꢂꢗꢓ ꢗꢒ ꢖ
SLOS175B − FEBRUARY 1997 − REVISED JANUARY 2008
APPLICATION INFORMATION
macromodel information (continued)
99
din
3
egnd
+
−
V
CC+
92
9
fb
+
91
90
rss
iss
ro2
hlim
−
+
−
+
vb
dip
rp
vip
vin
−
+
−
2
10
+
−
vc
IN−
IN+
r2
C2
j1
j2
7
dp
6
53
+
−
1
vlim
11
dc
12
ga
gcm
8
5
C1
ro1
rd1
rd2
de
54
4
V
CC−
+
−
ve
OUT
10 dc 135.0E−6
.subckt TLC220x 1 2 3 4 5
*
iss
iio
i1
3
2
88
0
.5E−12
c1
c2
11 12 8.51E−12
50.00E−12
0
1E−21
6
7
j1
11 89 10 jx
cpsr 85 86 79.6E−9
dcm+ 81 82 dx
j2
r2
12 80 10 jx
6
9
100.0E3
dcm− 83 81 dx
rcm 84 81 1k
dc
de
5
54
53 dx
dx
rn1 88
0
5
1500
188
5
ro1
8
dlp 90 91 dx
ro2
7
99 187
dln 92 90 dx
rss 10 99 1.481E6
vad 60 −.3v
dp
4
3
dx
4
ecmr 84 99 (2,99) 1
vcm+ 82 99 2.2
vcm− 83 99 −4.5
egnd 99
epsr 85
ense 89
0
0
2
poly(2) (3,0) (4,0) 0 .5 .5
poly(1) (3,4) −200E−6 20E−6
poly(1) (88,0) 100E−6 1
vb
vc
ve
vlim 7
vlp 91
9
3
54
0
dc 0
53 dc .9
fb
7
99 poly(6) vb vc ve vlp vln
4
8
0
dc .8
dc 0
dc 2.8
+
vpsr 0 +
895.9E3 −90E3 90E3 90E3 −90E3 895E3
11 12 314.2E−6
10 99 1.295E−9
ga
gcm
6
0
0
6
vln
0
92 dc 2.8
gpsr 85 86 (85,86) 100E−6
grd1 60 11 (60,11) 3.141E−4
grd2 60 12 (60,12) 3.141E−4
vpsr 0
86 dc 0
.model dx d(is=800.0E−18)
.model jx pjf(is=500.0E−15 beta=1.462E−3
+ vto=−.155 kf=1E−17)
.endsx
hlim 90
hcmr 80
0
1
4
vlim 1k
poly(2) vcm+ vcm− 0 1E2 1E2
965E−6
irp
3
Figure 40. Boyle Macromodel and Subcircuit
54
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
26-Aug-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
5962-9088201M2A
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
5962-
9088201M2A
TLC2201MFKB
5962-9088201MPA
5962-9088202M2A
ACTIVE
ACTIVE
CDIP
JG
FK
8
1
1
TBD
TBD
SNPB
N / A for Pkg Type
N / A for Pkg Type
-55 to 125
-55 to 125
9088201MPA
TLC2201M
LCCC
20
POST-PLATE
5962-
9088202M2A
TLC2202MFKB
5962-9088202MPA
5962-9088203QPA
5962-9088204Q2A
ACTIVE
ACTIVE
ACTIVE
CDIP
CDIP
LCCC
JG
JG
FK
8
8
1
1
1
TBD
TBD
TBD
SNPB
SNPB
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
-55 to 125
-55 to 125
-55 to 125
9088202MPA
TLC2202M
9088203QPA
TLC2201AM
20
POST-PLATE
5962-
9088204Q2A
TLC2202
AMFKB
5962-9088204QPA
TLC2201ACD
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
CDIP
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
JG
D
D
D
D
D
D
D
D
8
8
8
8
8
8
8
8
8
1
75
TBD
SNPB
N / A for Pkg Type
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-55 to 125
0 to 70
9088204QPA
TLC2202AM
Green (RoHS
& no Sb/Br)
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
2201AC
2201AC
2201AC
2201AI
2201AI
2201AI
2201AM
2201AM
TLC2201ACDR
TLC2201ACDRG4
TLC2201AID
2500
2500
75
Green (RoHS
& no Sb/Br)
0 to 70
Green (RoHS
& no Sb/Br)
0 to 70
Green (RoHS
& no Sb/Br)
TLC2201AIDG4
TLC2201AIDR
TLC2201AMD
75
Green (RoHS
& no Sb/Br)
2500
75
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
-55 to 125
TLC2201AMDG4
75
Green (RoHS
& no Sb/Br)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
26-Aug-2020
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TLC2201AMJG
TLC2201AMJGB
TLC2201CD
ACTIVE
CDIP
CDIP
SOIC
SOIC
SOIC
SOIC
PDIP
SOIC
SOIC
PDIP
LCCC
JG
JG
D
8
8
1
TBD
TBD
SNPB
N / A for Pkg Type
N / A for Pkg Type
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
N / A for Pkg Type
Level-1-260C-UNLIM
Level-1-260C-UNLIM
N / A for Pkg Type
N / A for Pkg Type
-55 to 125
-55 to 125
0 to 70
TLC2201
AMJG
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
1
SNPB
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
POST-PLATE
9088203QPA
TLC2201AM
8
75
Green (RoHS
& no Sb/Br)
2201C
TLC2201CDG4
TLC2201CDR
TLC2201CDRG4
TLC2201CP
D
8
75
Green (RoHS
& no Sb/Br)
0 to 70
2201C
D
8
2500
2500
50
Green (RoHS
& no Sb/Br)
0 to 70
2201C
D
8
Green (RoHS
& no Sb/Br)
0 to 70
2201C
P
8
Green (RoHS
& no Sb/Br)
0 to 70
TLC2201CP
2201I
TLC2201ID
D
8
75
Green (RoHS
& no Sb/Br)
TLC2201IDR
TLC2201IP
D
8
2500
50
Green (RoHS
& no Sb/Br)
2201I
P
8
Green (RoHS
& no Sb/Br)
TLC2201IP
TLC2201MFKB
FK
20
1
TBD
-55 to 125
5962-
9088201M2A
TLC2201MFKB
TLC2201MJGB
TLC2202ACD
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
CDIP
SOIC
SOIC
SOIC
SOIC
SOIC
JG
D
8
1
50
TBD
SNPB
N / A for Pkg Type
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-55 to 125
0 to 70
9088201MPA
TLC2201M
14
14
14
14
14
Green (RoHS
& no Sb/Br)
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
2202AC
2202AC
2202AC
2202AI
2202AI
TLC2202ACDR
TLC2202ACDRG4
TLC2202AID
D
2500
2500
50
Green (RoHS
& no Sb/Br)
D
Green (RoHS
& no Sb/Br)
D
Green (RoHS
& no Sb/Br)
-40 to 85
-40 to 85
TLC2202AIDG4
D
50
Green (RoHS
& no Sb/Br)
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
26-Aug-2020
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TLC2202AMFKB
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
5962-
9088204Q2A
TLC2202
AMFKB
TLC2202AMJG
TLC2202AMJGB
TLC2202CD
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
CDIP
CDIP
SOIC
SOIC
PDIP
SO
JG
JG
D
8
8
1
1
TBD
TBD
SNPB
SNPB
N / A for Pkg Type
N / A for Pkg Type
Level-1-260C-UNLIM
Level-1-260C-UNLIM
N / A for Pkg Type
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
-55 to 125
-55 to 125
0 to 70
TLC2202
AMJG
9088204QPA
TLC2202AM
14
14
8
50
Green (RoHS
& no Sb/Br)
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
POST-PLATE
2202C
TLC2202CDR
TLC2202CP
D
2500
50
Green (RoHS
& no Sb/Br)
0 to 70
2202C
P
Green (RoHS
& no Sb/Br)
TLC2202CP
P2202
TLC2202CPS
TLC2202CPSR
TLC2202ID
PS
PS
D
8
80
Green (RoHS
& no Sb/Br)
SO
8
2000
50
Green (RoHS
& no Sb/Br)
P2202
SOIC
SOIC
PDIP
PDIP
LCCC
14
14
8
Green (RoHS
& no Sb/Br)
TLC2202I
TLC2202I
TLC2202IP
TLC2202IP
TLC2202IDG4
TLC2202IP
D
50
Green (RoHS
& no Sb/Br)
P
50
Green (RoHS
& no Sb/Br)
TLC2202IPE4
TLC2202MFKB
P
8
50
Green (RoHS
& no Sb/Br)
FK
20
1
TBD
-55 to 125
5962-
9088202M2A
TLC2202MFKB
TLC2202MJG
ACTIVE
ACTIVE
CDIP
CDIP
JG
JG
8
8
1
1
TBD
TBD
SNPB
SNPB
N / A for Pkg Type
N / A for Pkg Type
-55 to 125
-55 to 125
TLC2202MJG
TLC2202MJGB
9088202MPA
TLC2202M
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
Addendum-Page 3
PACKAGE OPTION ADDENDUM
www.ti.com
26-Aug-2020
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TLC2201, TLC2201A, TLC2201AM, TLC2201M, TLC2202, TLC2202A, TLC2202AM, TLC2202M :
Catalog: TLC2201A, TLC2201, TLC2202A, TLC2202
•
Military: TLC2201M, TLC2201AM, TLC2202M, TLC2202AM
•
Space: TLC2201-SP, TLC2201-SP
•
NOTE: Qualified Version Definitions:
Addendum-Page 4
PACKAGE OPTION ADDENDUM
www.ti.com
26-Aug-2020
Catalog - TI's standard catalog product
•
•
•
Military - QML certified for Military and Defense Applications
Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application
Addendum-Page 5
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Feb-2019
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TLC2201ACDR
TLC2201AIDR
TLC2201CDR
TLC2201IDR
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
D
D
D
D
D
D
8
8
2500
2500
2500
2500
2500
2500
330.0
330.0
330.0
330.0
330.0
330.0
12.4
12.4
12.4
12.4
16.4
16.4
6.4
6.4
6.4
6.4
6.5
6.5
5.2
5.2
5.2
5.2
9.0
9.0
2.1
2.1
2.1
2.1
2.1
2.1
8.0
8.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
16.0
16.0
Q1
Q1
Q1
Q1
Q1
Q1
8
8
TLC2202ACDR
TLC2202CDR
14
14
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Feb-2019
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TLC2201ACDR
TLC2201AIDR
TLC2201CDR
TLC2201IDR
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
D
D
D
D
D
D
8
8
2500
2500
2500
2500
2500
2500
340.5
340.5
340.5
340.5
350.0
350.0
338.1
338.1
338.1
338.1
350.0
350.0
20.6
20.6
20.6
20.6
43.0
43.0
8
8
TLC2202ACDR
TLC2202CDR
14
14
Pack Materials-Page 2
PACKAGE OUTLINE
D0008A
SOIC - 1.75 mm max height
SCALE 2.800
SMALL OUTLINE INTEGRATED CIRCUIT
C
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
.004 [0.1] C
A
PIN 1 ID AREA
6X .050
[1.27]
8
1
2X
.189-.197
[4.81-5.00]
NOTE 3
.150
[3.81]
4X (0 -15 )
4
5
8X .012-.020
[0.31-0.51]
B
.150-.157
[3.81-3.98]
NOTE 4
.069 MAX
[1.75]
.010 [0.25]
C A B
.005-.010 TYP
[0.13-0.25]
4X (0 -15 )
SEE DETAIL A
.010
[0.25]
.004-.010
[0.11-0.25]
0 - 8
.016-.050
[0.41-1.27]
DETAIL A
TYPICAL
(.041)
[1.04]
4214825/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
SEE
DETAILS
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:8X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED
METAL
EXPOSED
METAL
.0028 MAX
[0.07]
.0028 MIN
[0.07]
ALL AROUND
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214825/C 02/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
SOLDER PASTE EXAMPLE
BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
4214825/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUARY 1997
JG (R-GDIP-T8)
CERAMIC DUAL-IN-LINE
0.400 (10,16)
0.355 (9,00)
8
5
0.280 (7,11)
0.245 (6,22)
1
4
0.065 (1,65)
0.045 (1,14)
0.310 (7,87)
0.290 (7,37)
0.063 (1,60)
0.015 (0,38)
0.020 (0,51) MIN
0.200 (5,08) MAX
0.130 (3,30) MIN
Seating Plane
0.023 (0,58)
0.015 (0,38)
0°–15°
0.100 (2,54)
0.014 (0,36)
0.008 (0,20)
4040107/C 08/96
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification.
E. Falls within MIL STD 1835 GDIP1-T8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated
©2020 ICPDF网 联系我们和版权申明