OP-07DPS [TI]
OP07x Precision Operational Amplifiers;型号: | OP-07DPS |
厂家: | TEXAS INSTRUMENTS |
描述: | OP07x Precision Operational Amplifiers |
文件: | 总22页 (文件大小:1067K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Sample &
Buy
Support &
Community
Product
Folder
Tools &
Software
Technical
Documents
OP07C, OP07D
SLOS099G –OCTOBER 1983–REVISED NOVEMBER 2014
OP07x Precision Operational Amplifiers
1 Features
3 Description
These devices offer low offset and long-term stability
by means of low-noise, chopperless,
1
•
•
•
•
•
Low Noise
a
No External Components Required
bipolar-input-transistor amplifier circuit. For most
applications, external components are not required
for offset nulling and frequency compensation. The
true differential input, with a wide input-voltage range
and outstanding common-mode rejection, provides
maximum flexibility and performance in high-noise
environments and in noninverting applications. Low
bias currents and extremely high input impedances
are maintained over the entire temperature range.
Replace Chopper Amplifiers at a Lower Cost
Wide Input-Voltage Range: 0 to ±14 V (Typ)
Wide Supply-Voltage Range: ±3 V to ±18 V
2 Applications
•
•
•
•
•
Wireless Base Station Control Circuits
Optical Network Control Circuits
Instrumentation
Device Information(1)
Sensors and Controls
PART NUMBER
PACKAGE (PIN)
BODY SIZE
Precision Filters
SO (8)
6.20 mm × 5.30 mm
4.90 mm × 3.91 mm
9.81 mm × 6.35 mm
OP07x
SOIC (8)
PDIP (8)
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
4 Simplified Schematic
1
3
OFFSET N1
IN+
+
−
6
OUT
2
8
IN−
OFFSET N2
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
OP07C, OP07D
SLOS099G –OCTOBER 1983–REVISED NOVEMBER 2014
www.ti.com
Table of Contents
9.2 Functional Block Diagram ......................................... 7
9.3 Feature Description................................................... 7
9.4 Device Functional Modes.......................................... 7
10 Application and Implementation.......................... 8
10.1 General Application................................................. 8
10.2 Typical Application ................................................. 8
11 Power Supply Recommendations ..................... 10
12 Layout................................................................... 11
12.1 Layout Guidelines ................................................. 11
12.2 Layout Example .................................................... 11
13 Device and Documentation Support ................. 12
13.1 Related Links ........................................................ 12
13.2 Trademarks........................................................... 12
13.3 Electrostatic Discharge Caution............................ 12
13.4 Glossary................................................................ 12
1
2
3
4
5
6
7
Features.................................................................. 1
Applications ........................................................... 1
Description ............................................................. 1
Simplified Schematic............................................. 1
Revision History..................................................... 2
Pin Functions ......................................................... 3
Specifications......................................................... 4
7.1 Absolute Maximum Ratings ...................................... 4
7.2 Handling Ratings....................................................... 4
7.3 Recommended Operating Conditions....................... 4
7.4 Thermal Information.................................................. 4
7.5 Electrical Characteristics........................................... 5
7.6 Operating Characteristics.......................................... 6
Typical Characteristics.......................................... 6
Detailed Description .............................................. 7
9.1 Overview ................................................................... 7
8
9
14 Mechanical, Packaging, and Orderable
Information ........................................................... 12
5 Revision History
Changes from Revision F (January 2014) to Revision G
Page
•
Added Applications, Device Information table, Pin Functions table, Handling Ratings table, Thermal Information
table, Typical Characteristics, Feature Description section, Device Functional Modes, Application and
Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation
Support section, and Mechanical, Packaging, and Orderable Information section................................................................ 1
Changes from Revision E (May 2004) to Revision F
Page
•
Deleted Ordering Information table. ....................................................................................................................................... 1
2
Submit Documentation Feedback
Copyright © 1983–2014, Texas Instruments Incorporated
Product Folder Links: OP07C OP07D
OP07C, OP07D
www.ti.com
SLOS099G –OCTOBER 1983–REVISED NOVEMBER 2014
6 Pin Functions
D OR P PACKAGE
(TOP VIEW)
OFFSET N1
IN−
OFFSET N2
1
2
3
4
8
7
6
5
V
CC+
IN+
OUT
NC
V
CC−
NC−No internal connection
Pin Functions
PIN
TYPE
DESCRIPTION
NAME
IN+
NO.
3
2
5
1
8
6
7
4
I
I
Noninverting input
Inverting input
IN–
NC
—
I
Do not connect
OFFSET N1
OFFSET N2
OUT
External input offset voltage adjustment
External input offset voltage adjustment
Output
I
O
—
—
VCC
+
–
Positive supply
VCC
Negative supply
Copyright © 1983–2014, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: OP07C OP07D
OP07C, OP07D
SLOS099G –OCTOBER 1983–REVISED NOVEMBER 2014
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN
0
MAX UNIT
(2)
VCC+
22
V
Supply voltage
(2)
VCC–
–22
0
Differential input voltage(3)
Input voltage range (either input)(4)
±30
±22
V
V
VI
Duration of output short circuit(5)
Unlimited
150
TJ
Operating virtual-junction temperature
Lead temperature 1.6 mm (1/16 in) from case for 10 s
°C
°C
260
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values, unless otherwise noted, are with respect to the midpoint between VCC+ and VCC−
.
(3) Differential voltages are at IN+ with respect to IN−.
(4) The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 V, whichever is less.
(5) The output may be shorted to ground or to either power supply.
7.2 Handling Ratings
PARAMETER
DEFINITION
MIN
MAX UNIT
TSTG
Storage temperature range
–65
150
°C
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all
pins(1)
0
0
1000
Electrostatic
Discharge
V(ESD)
V
Charged device model (CDM), per JEDEC specification JESD22-
C101, all pins(2)
1000
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
UNIT
V
VCC+
VCC–
VIC
3
–3
18
–18
13
Supply voltage
Common-mode input voltage
Operating free-air temperature
VCC± = ±15 V
–13
0
TA
70
°C
7.4 Thermal Information
THERMAL METRIC(1)
D
P
UNIT
°C/W
RθJA
Junction-to-ambient thermal resistance
97
85
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report (SPRA953).
4
Submit Documentation Feedback
Copyright © 1983–2014, Texas Instruments Incorporated
Product Folder Links: OP07C OP07D
OP07C, OP07D
www.ti.com
SLOS099G –OCTOBER 1983–REVISED NOVEMBER 2014
7.5 Electrical Characteristics
at specified free-air temperature, VCC± = ±15 V (unless otherwise noted)(1)
OP07C
TYP MAX
OP07D
TYP
(2)
PARAMETER
TEST CONDITIONS
TA
UNIT
MIN
MIN
MAX
150
25°C
60
85
VIO
Input offset voltage
VO = 0 V
RS = 50 Ω
RS = 50 Ω
µV
0°C to 70°C
250
Temperature coefficient
of input offset voltage
αVIO
VO = 0 V
0°C to 70°C
0.5
0.4
2.5
µV/°C
Long-term drift of input
offset voltage
See
µV/mo
mV
Offset adjustment range
RS = 20 kΩ,
See Figure 2
25°C
25°C
±4
0.8
1.6
6
8
IIO
Input offset current
nA
pA/°C
nA
0°C to 70°C
Temperature coefficient
of input offset current
αIIO
0°C to 70°C
12
50
25°C
±1.8
±2.2
±12
±14
IIB
Input bias current
0°C to 70°C
Temperature coefficient
of input bias current
αIIB
0°C to 70°C
18
50
pA/°C
V
25°C
±13
±13
±14
±13.5
±13
±13
±14
Common-mode input
voltage range
VICR
0°C to 70°C
±13 ±13.5
±12 ±13
R
R
R
R
L ≥ 10 kΩ
L ≥ 2 kΩ
L ≥ 1 kΩ
L ≥ 2 kΩ
±12
25°C
±11.5
±12.8
±12
±11.5 ±12.8
±12
VOM
Peak output voltage
V
0°C to 70°C
25°C
±11
100
±12.6
±11 ±12.6
VCC = 15 V, VO = 1.4 V to 11.4 V,
L ≥ 500 kΩ
400
400
R
Large-signal differential
voltage amplification
AVD
V/mV
25°C
0°C to 70°C
25°C
120
100
0.4
8
400
400
0.6
33
120
100
0.4
7
400
400
0.6
31
VO = ±10, RL = 2 kΩ
B1
ri
Unity-gain bandwidth
Input resistance
MHz
25°C
MΩ
25°C
100
97
120
120
7
94
110
106
7
Common-mode
rejection ratio
CMRR
kSVS
PD
VIC = ±13 V, RS = 50 Ω
dB
0°C to 70°C
25°C
94
32
51
32
51
Supply-voltage sensitivity
VCC+ = ±3 V to ±18 V, RS = 50 Ω
µV/V
mW
(ΔVIO/ΔVCC
)
0°C to 70°C
10
10
VO = 0, No load
80
150
8
80
150
8
Power dissipation
25°C
VCC+ = ±3 V, VO = 0, No load
4
4
(1) Because long-term drift cannot be measured on the individual devices prior to shipment, this specification is not intended to be a
warranty. It is an engineering estimate of the averaged trend line of drift versus time over extended periods after the first 30 days of
operation.
(2) All characteristics are measured with zero common-mode input voltage, unless otherwise specified.
Copyright © 1983–2014, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: OP07C OP07D
OP07C, OP07D
SLOS099G –OCTOBER 1983–REVISED NOVEMBER 2014
www.ti.com
7.6 Operating Characteristics
at specified free-air temperature, VCC = 5 V (unless otherwise noted)
OP07C
TYP
10.5
10.2
9.8
OP07D
TYP
10.5
10.3
9.8
PARAMETER
TEST CONDITIONS(1)
UNIT
f = 10 Hz
Vn
Input offset voltage
f = 100 Hz
nV/√Hz
µV
f = 1 kHz
VN(PP)
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
f = 0.1 Hz to 10 Hz
f = 10 Hz
0.38
0.35
0.15
0.13
15
0.38
0.35
0.15
0.13
15
In
f = 100 Hz
nV/√Hz
f = 1 kHz
IN(PP)
SR
Peak-to-peak equivalent input noise current
Slew rate
f = 0.1 Hz to 10 Hz
pA
RL ≥ 2 kΩ
0.3
0.3
V/µs
(1) All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise noted.
8 Typical Characteristics
200
Low
Mean
High
150
100
50
0
-50
-50
0
50
100
150
T (°C)
D001
Figure 1. Input-Offset Voltage vs. Temperature
6
Submit Documentation Feedback
Copyright © 1983–2014, Texas Instruments Incorporated
Product Folder Links: OP07C OP07D
OP07C, OP07D
www.ti.com
SLOS099G –OCTOBER 1983–REVISED NOVEMBER 2014
9 Detailed Description
9.1 Overview
These devices offer low offset and long-term stability by means of a low-noise, chopperless, bipolar-input-
transistor amplifier circuit. For most applications, external components are not required for offset nulling and
frequency compensation. The true differential input, with a wide input-voltage range and outstanding common-
mode rejection, provides maximum flexibility and performance in high-noise environments and in noninverting
applications. Low bias currents and extremely high input impedances are maintained over the entire temperature
range.
These devices are characterized for operation from 0°C to 70°C.
9.2 Functional Block Diagram
V
CC+
IN–
OUT
IN+
OFFSET N1
OFFSET N2
V
CC–
Component Count
Transistors
Resistors
Diode
22
11
1
Capacitor
1
9.3 Feature Description
9.3.1 Offset-Voltage Null Capability
The input offset voltage of operational amplifiers (op amps) arises from unavoidable mismatches in the
differential input stage of the op-amp circuit caused by mismatched transistor pairs, collector currents, current-
gain betas (β), collector or emitter resistors, et cetera. The input offset pins allow the designer to adjust for these
mismatches by external circuitry. See the Application and Implementation section for more details on design
techniques.
9.3.2 Slew Rate
The slew rate is the rate at which an operational amplifier can change its output when there is a change on the
input. The OP07 has a 0.3-V/μs slew rate.
9.4 Device Functional Modes
The OP07 is powered on when the supply is connected. It can be operated as a single supply operational
amplifier or dual supply amplifier depending on the application.
Copyright © 1983–2014, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: OP07C OP07D
OP07C, OP07D
SLOS099G –OCTOBER 1983–REVISED NOVEMBER 2014
www.ti.com
10 Application and Implementation
10.1 General Application
The input offset voltage of operational amplifiers (op amps) arises from unavoidable mismatches in the
differential input stage of the op-amp circuit caused by mismatched transistor pairs, collector currents, current-
gain betas (β), collector or emitter resistors, etc. The input offset pins allow the designer to adjust for these
mismatches by external circuitry. These input mismatches can be adjusted by putting resistors or a potentiometer
between the inputs as shown in Figure 2. A potentiometer can be used to fine tune the circuit during testing or for
applications which require precision offset control. More information about designing using the input-offset pins,
see Nulling Input Offset Voltage of Operational Amplifiers (SLOA045).
20 kΩ
V
CC+
OFFSET N1
3
OFFSET
1
N2
8
IN+
+
7
6
OUT
2
−
IN−
4
V
CC
–
Figure 2. Input Offset-Voltage Null Circuit
10.2 Typical Application
The voltage follower configuration of the operational amplifier is used for applications where a weak signal is
used to drive a relatively high current load. This circuit is also called a buffer amplifier or unity gain amplifier. The
inputs of an operational amplifier have a very high resistance which puts a negligible current load on the voltage
source. The output resistance of the operational amplifier is almost negligible, so it can provide as much current
as necessary to the output load.
10 kꢀ
12 V
VOUT
+
VIN
Figure 3. Voltage Follower Schematic
8
Submit Documentation Feedback
Copyright © 1983–2014, Texas Instruments Incorporated
Product Folder Links: OP07C OP07D
OP07C, OP07D
www.ti.com
SLOS099G –OCTOBER 1983–REVISED NOVEMBER 2014
Typical Application (continued)
10.2.1 Design Requirements
•
•
Output range of 2 V to 11 V
Input range of 2 V to 11 V
10.2.2 Detailed Design Procedure
10.2.2.1 Output Voltage Swing
The output voltage of an operational amplifier is limited by its internal circuitry to some level below the supply
rails. For this amplifier, the output voltage swing is within ±12 V, which accommodates the input and output
voltage requirements.
10.2.2.2 Supply and Input Voltage
For correct operation of the amplifier, neither input must be higher than the recommended positive supply rail
voltage or lower than the recommended negative supply rail voltage. The chosen amplifier must be able to
operate at the supply voltage that accommodates the inputs. Because the input for this application goes up to
11 V, the supply voltage must be 12 V. Using a negative voltage on the lower rail, rather than ground, allows the
amplifier to maintain linearity for inputs below 2 V.
10.2.3 Application Curves for Output Characteristics
12
10
8
0.4
0.3
0.2
0.1
6
0.0
4
±0.1
±0.2
±0.3
2
0
0
2
4
6
8
10
12
0
2
4
6
8
10
12
VIN (V)
VIN (V)
C001
C002
Figure 4. Output Voltage vs Input Voltage
Figure 5. Current Drawn by the Input of the Voltage
Follower (IIO) vs the Input Voltage
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0
2
4
6
8
10
12
VIN (V)
C003
Figure 6. Current Drawn from Supply (ICC) vs the Input Voltage
Copyright © 1983–2014, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: OP07C OP07D
OP07C, OP07D
SLOS099G –OCTOBER 1983–REVISED NOVEMBER 2014
www.ti.com
11 Power Supply Recommendations
The OP07 is specified for operation from ±3 to ±18 V; many specifications apply from 0°C to 70°C.
CAUTION
Supply voltages larger than ±22 V can permanently damage the device (see the
Absolute Maximum Ratings).
Place 0.1-μF bypass capacitors close to the power-supply pins to reduce errors coupling in from noisy or high
impedance power supplies. For more detailed information on bypass capacitor placement, refer to the Layout
Guidelines.
10
Submit Documentation Feedback
Copyright © 1983–2014, Texas Instruments Incorporated
Product Folder Links: OP07C OP07D
OP07C, OP07D
www.ti.com
SLOS099G –OCTOBER 1983–REVISED NOVEMBER 2014
12 Layout
12.1 Layout Guidelines
For best operational performance of the device, use good PCB layout practices, including:
•
Noise can propagate into analog circuitry through the power pins of the circuit as a whole, as well as the
operational amplifier. Bypass capacitors are used to reduce the coupled noise by providing low-impedance
power sources local to the analog circuitry.
–
Connect low-ESR, 0.1-μF ceramic bypass capacitors between each supply pin and ground, placed as
close to the device as possible. A single bypass capacitor from V+ to ground is applicable for single
supply applications.
•
•
Separate grounding for analog and digital portions of circuitry is one of the simplest and most-effective
methods of noise suppression. On multilayer PCBs, one or more layers are usually devoted to ground planes.
A ground plane helps distribute heat and reduces EMI noise pickup. Make sure to physically separate digital
and analog grounds, paying attention to the flow of the ground current. For more detailed information, refer to
Circuit Board Layout Techniques, (SLOA089).
To reduce parasitic coupling, run the input traces as far away from the supply or output traces as possible. If
it is not possible to keep them separate, it is much better to cross the sensitive trace perpendicularly, as
opposed to in parallel, with the noisy trace.
•
•
•
Place the external components as close to the device as possible. Keeping RF and RG close to the inverting
input minimizes parasitic capacitance, as shown in Layout Example.
Keep the length of input traces as short as possible. Always remember that the input traces are the most
sensitive part of the circuit.
Consider a driven, low-impedance guard ring around the critical traces. A guard ring can significantly reduce
leakage currents from nearby traces that are at different potentials.
12.2 Layout Example
RIN
RG
VIN
+
VOUT
RF
Figure 7. Operational Amplifier Schematic for Noninverting Configuration
Place components close to
device and to each other to
reduce parasitic errors
Run the input traces as far
away from the supply lines
as possible
RF
VS+
OFFSET N1
OFFSET N2
VCC+
OUT
Use low-ESR, ceramic
bypass capacitor
RG
GND
VIN
IN1í
IN1+
RIN
GND
NC
VCCí
Only needed for
dual-supply
operation
GND
VS-
(or GND for single supply)
VOUT
Ground (GND) plane on another layer
Figure 8. Operational Amplifier Board Layout for Noninverting Configuration
Copyright © 1983–2014, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: OP07C OP07D
OP07C, OP07D
SLOS099G –OCTOBER 1983–REVISED NOVEMBER 2014
www.ti.com
13 Device and Documentation Support
13.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 1. Related Links
Technical
Documents
Support &
Community
Parts
Product Folder
Sample & Buy
Tools & Software
OP07C
OP07D
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
13.2 Trademarks
All trademarks are the property of their respective owners.
13.3 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
13.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms and definitions.
14 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser based versions of this data sheet, refer to the left hand navigation.
12
Submit Documentation Feedback
Copyright © 1983–2014, Texas Instruments Incorporated
Product Folder Links: OP07C OP07D
PACKAGE OPTION ADDENDUM
www.ti.com
26-Aug-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
OP-07DP
OP-07DPS
ACTIVE
PDIP
SO
P
8
8
8
8
50
Green (RoHS
& no Sb/Br)
NIPDAU
N / A for Pkg Type
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
0 to 70
0 to 70
0 to 70
0 to 70
OP-07DP
ACTIVE
ACTIVE
ACTIVE
PS
PS
PS
80
Green (RoHS
& no Sb/Br)
NIPDAU
NIPDAU
NIPDAU
OP-07D
OP-07D
OP-07D
OP-07DPSR
OP-07DPSRG4
SO
2000
2000
Green (RoHS
& no Sb/Br)
SO
Green (RoHS
& no Sb/Br)
OP07-W
OP07CD
ACTIVE WAFERSALE
YS
D
0
8
3603
75
TBD
Call TI
Call TI
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
PDIP
PDIP
SOIC
SOIC
SOIC
PDIP
Green (RoHS
& no Sb/Br)
NIPDAU
Level-1-260C-UNLIM
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
OP07C
OP07C
OP07C
OP07C
OP07C
OP07C
OP07CP
OP07CP
OP07D
OP07D
OP07D
OP07DP
OP07CDE4
OP07CDG4
OP07CDR
OP07CDRE4
OP07CDRG4
OP07CP
D
D
D
D
D
P
P
D
D
D
P
8
8
8
8
8
8
8
8
8
8
8
75
75
Green (RoHS
& no Sb/Br)
NIPDAU
NIPDAU
NIPDAU | SN
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
N / A for Pkg Type
Green (RoHS
& no Sb/Br)
2500
2500
2500
50
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
OP07CPE4
OP07DD
50
Green (RoHS
& no Sb/Br)
N / A for Pkg Type
75
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
N / A for Pkg Type
OP07DDR
OP07DDRE4
OP07DP
2500
2500
50
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Pb-Free
(RoHS)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
26-Aug-2020
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
OP07DPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
NIPDAU
N / A for Pkg Type
0 to 70
OP07DP
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Jul-2020
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
OP07CDR
OP07CDRG4
OP07DDR
SOIC
SOIC
SOIC
D
D
D
8
8
8
2500
2500
2500
330.0
330.0
330.0
12.4
12.4
12.4
6.4
6.4
6.4
5.2
5.2
5.2
2.1
2.1
2.1
8.0
8.0
8.0
12.0
12.0
12.0
Q1
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Jul-2020
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
OP07CDR
OP07CDRG4
OP07DDR
SOIC
SOIC
SOIC
D
D
D
8
8
8
2500
2500
2500
340.5
340.5
340.5
338.1
338.1
338.1
20.6
20.6
20.6
Pack Materials-Page 2
PACKAGE OUTLINE
D0008A
SOIC - 1.75 mm max height
SCALE 2.800
SMALL OUTLINE INTEGRATED CIRCUIT
C
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
.004 [0.1] C
A
PIN 1 ID AREA
6X .050
[1.27]
8
1
2X
.189-.197
[4.81-5.00]
NOTE 3
.150
[3.81]
4X (0 -15 )
4
5
8X .012-.020
[0.31-0.51]
B
.150-.157
[3.81-3.98]
NOTE 4
.069 MAX
[1.75]
.010 [0.25]
C A B
.005-.010 TYP
[0.13-0.25]
4X (0 -15 )
SEE DETAIL A
.010
[0.25]
.004-.010
[0.11-0.25]
0 - 8
.016-.050
[0.41-1.27]
DETAIL A
TYPICAL
(.041)
[1.04]
4214825/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
SEE
DETAILS
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:8X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED
METAL
EXPOSED
METAL
.0028 MAX
[0.07]
.0028 MIN
[0.07]
ALL AROUND
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214825/C 02/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
SOLDER PASTE EXAMPLE
BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
4214825/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated
相关型号:
OP-07DZ
Operational Amplifier, 1 Func, 250uV Offset-Max, BIPolar, CDIP8, HERMETIC SEALED, DIP-8
Linear
OP-07EH#PBF
IC OP-AMP, 130 uV OFFSET-MAX, 0.6 MHz BAND WIDTH, MBCY8, LEAD FREE, METAL CAN-8, Operational Amplifier
Linear
OP-07EJG
OP-AMP, 130uV OFFSET-MAX, 0.6MHz BAND WIDTH, CDIP8, 0.300 INCH, HERMETIC SEALED, CERAMIC, DIP-8
TI
©2020 ICPDF网 联系我们和版权申明