LP8758A2E3YFFR [TI]
四路、单相、4A 输出直流/直流降压转换器 | YFF | 35 | -40 to 85;
| 型号： | LP8758A2E3YFFR |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 四路、单相、4A 输出直流/直流降压转换器 | YFF | 35 | -40 to 85 转换器 |
| 文件： | 总56页 (文件大小：963K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
LP8758-E3
SNVSBP2 –FEBRUARY 2020
LP8758-E3 Four 4-A Output Synchronous Step-Down DCDC Converters
Check for Samples: LP8758-E3
1 Features
3 Description
The LP8758-E3 device is designed to meet power
management requirements for low-power processors
in mobile phones, network cards, and similar
applications. The device contains four step-down DC-
DC converter cores, providing four output voltage
rails. The device is controlled by an I2C-compatible
serial interface.
1
•
Fully Integrated Quad Buck, up to 4-A
Programmable Maximum Output Current Per
Buck
–
–
Auto PWM-PFM and Forced-PWM Operations
Programmable Output Voltage Slew Rate
From 30 mV/µs to 0.5 mV/µs
–
–
Input Voltage Range: 2.5 V to 5.5 V
VOUT Range: 0.5 V to 3.36 V with DVS
The automatic PWM-PFM (AUTO mode) operation
maximizes efficiency over a wide output-current
range.
•
•
Programmable Start-Up and Shutdown
Sequencing With Enable Signal
I2C-Compatible Interface That Supports Standard
(100 kHz), Fast (400 kHz),
The LP8758-E3 supports programmable start-up and
shutdown sequencing synchronized to hardware
Enable input signal.
The protection features include short-circuit
protection, current limits, input supply UVLO, and
temperature warning and shutdown functions.
Several error flags are provided for status information
of the device. In addition, the LP8758-E3 device
supports load current measurement without the
addition of external current sense resistors. During
start-up and voltage change, the device controls the
output slew rate to minimize output voltage overshoot
and the inrush current.
Fast+ (1 MHz), and High-Speed (3.4 MHz) Modes
•
•
•
•
•
Interrupt Function with Programmable Masking
Load Current Measurement
Output Short-Circuit and Overload Protection
Spread-Spectrum Mode for EMI Reduction
The Four Buck Cores Operate 90° out of Phase
Thereby Reducing Input Ripple Current
•
•
Overtemperature Warning and Protection
Undervoltage Lockout (UVLO)
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
2 Applications
•
•
•
•
Optical Modules
Drone Systems
Smart Phones, eBooks, and Tablets
Solid State Drives
Simplified Schematic
Efficiency vs Output Current
100
LP8758
VIN
VOUT0
VOUT1
VOUT2
VOUT3
VIN_B0
VIN_B1
VIN_B2
VIN_B3
VANA
SW_B0
FB_B0
95
90
85
80
SW_B1
FB_B1
NRST
SDA
SCL
nINT
EN1
EN2
SW_B2
FB_B2
VIN = 3.3 V
2.5 V
1.8 V
75
SW_B3
FB_B3
70
0.001
0.01
0.1
Output Current (A)
1
5
GNDs
D038
VOUT settings = 1.8 V and 2.5 V
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
Table of Contents
7.5 Programming........................................................... 23
7.6 Register Maps......................................................... 26
Application and Implementation ........................ 43
8.1 Application Information............................................ 43
8.2 Typical Application .................................................. 43
Power Supply Recommendations...................... 50
1
2
3
4
5
6
Features.................................................................. 1
Applications ........................................................... 1
Description ............................................................. 1
Revision History..................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 5
6.1 Absolute Maximum Ratings ...................................... 5
6.2 ESD Ratings.............................................................. 5
6.3 Recommended Operating Conditions....................... 5
6.4 Thermal Information.................................................. 6
6.5 Electrical Characteristics........................................... 6
6.6 I2C Serial Bus Timing Requirements ........................ 8
6.7 Switching Characteristics........................................ 10
6.8 Typical Characteristics............................................ 11
Detailed Description ............................................ 12
7.1 Overview ................................................................. 12
7.2 Functional Block Diagram ....................................... 13
7.3 Feature Description................................................. 13
7.4 Device Functional Modes........................................ 22
8
9
10 Layout................................................................... 51
10.1 Layout Guidelines ................................................. 51
10.2 Layout Example .................................................... 52
11 Device and Documentation Support ................. 53
11.1 Device Support...................................................... 53
11.2 Documentation Support ........................................ 53
11.3 Receiving Notification of Documentation Updates 53
11.4 Community Resources.......................................... 53
11.5 Trademarks........................................................... 53
11.6 Electrostatic Discharge Caution............................ 53
11.7 Glossary................................................................ 53
7
12 Mechanical, Packaging, and Orderable
Information ........................................................... 53
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
DATE
REVISION
NOTES
February 2020
*
Initial Release
2
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
5 Pin Configuration and Functions
YFF Package
35-Pin DSBGA
Top View
YFF Package
35-Pin DSBGA
Bottom View
VIN
_B2
SW
_B2
PGND
_B23
SW
_B3
VIN
_B3
G
F
VIN
_B3
SW
_B3
PGND
_B23
SW
_B2
VIN
_B2
G
F
VIN
_B2
SW
_B2
PGND
_B23
SW
_B3
VIN
_B3
VIN
_B3
SW
_B3
PGND
_B23
SW
_B2
VIN
_B2
FB
_B2
PGND
_B23
FB
_B3
SCL
SDA
EN1
VANA
E
D
C
B
A
FB
_B3
PGND
_B23
FB
_B2
VANA
SCL
SDA
EN1
E
D
C
B
A
AGN
D
NRST
EN2
nINT
AGN
D
nINT
EN2
NRST
FB
_B0
PGND
_B01
FB
_B1
SGND
FB
_B1
PGND
_B01
FB
_B0
SGND
VIN
_B0
SW
_B0
PGND
_B01
SW
_B1
VIN
_B1
VIN
_B1
SW
_B1
PGND
_B01
SW
_B0
VIN
_B0
VIN
_B0
SW
_B0
PGND
_B01
SW
_B1
VIN
_B1
VIN
_B1
SW
_B1
PGND
_B01
SW
_B0
VIN
_B0
5
4
3
2
1
1
2
3
4
5
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
Pin Functions
PIN
TYPE
DESCRIPTION
NUMBER
NAME
Input for Buck1. The separate power pins VIN_Bx are not connected together internally – VIN_Bx
pins must be connected together in the application and be locally bypassed.
A1, B1
VIN_B1
P
A2, B2
SW_B1
PGND_B01
SW_B0
A
G
A
Buck1 switch node.
A3, B3, C3
A4, B4
Power Ground for Buck0 and Buck1.
Buck0 switch node.
Input for Buck0. The separate power pins VIN_Bx are not connected together internally – VIN_Bx
pins must be connected together in the application and be locally bypassed.
A5, B5
VIN_B0
P
C1
C2
C4
SGND
FB_B1
FB_B0
G
A
A
Substrate Ground.
Output voltage feedback for Buck1.
Output voltage feedback for Buck0.
Programmable Enable signal for Buck converter core or cores. Can be also configured to switch
between two output voltage levels.
C5
EN1
D/I
D1
D2
AGND
nINT
G
Ground.
D/O
Open-drain interrupt output. Active LOW.
Programmable Enable signal for Buck converter one or more cores. Can be also configured to
switch between two output voltage levels.
D3
EN2
D/I
D4
D5
E1
E2
E4
E5
NRST
SDA
D/I
Reset signal for the device. Can be also used to enable the regulator.
D/I/O Serial interface data input and output for system access. Connect a pullup resistor.
VANA
FB_B3
FB_B2
SCL
P
A
Supply voltage for Analog and Digital blocks.
Output voltage feedback for Buck3.
A
Output voltage feedback for Buck2.
D/I
Serial interface clock input for system access. Connect a pullup resistor.
Input for Buck3. The separate power pins VIN_Bx are not connected together internally – VIN_Bx
pins must be connected together in the application and be locally bypassed.
F1, G1
VIN_B3
P
F2, G2
SW_B3
PGND_B23
SW_B2
A
G
A
Buck3 switch node.
E3, F3, G3
F4, G4
Power Ground for Buck2 and Buck3.
Buck2 switch node.
Input for Buck2. The separate power pins VIN_Bx are not connected together internally - VIN_Bx
pins must be connected together in the application and be locally bypassed.
F5, G5
VIN_B2
P
A: Analog Pin, D: Digital Pin, G: Ground Pin, P: Power Pin, I: Input Pin, O: Output Pin
4
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
6 Specifications
6.1 Absolute Maximum Ratings
Over operating free-air temperature range (unless otherwise noted).(1)(2)
MIN
MAX
UNIT
INPUT VOLTAGE
VIN_Bx, VANA
Voltage on power connections
Voltage on buck switch nodes
–0.3
–0.3
6
V
V
(VIN_Bx + 0.3 V) with
6 V maximum
SW_Bx
(VANA + 0.3 V) with
6 V maximum
FB_Bx
Voltage on buck voltage sense nodes
–0.3
V
V
NRST
Voltage on NRST input
–0.3
–0.3
3.6
3.6
ENx, SDA, SCL, nINT
CURRENT
Voltage on logic pins (input or output pins)
VIN_Bx, SW_Bx,
PGND_Bx
Current on power pins (average current over 100k
hour lifetime, TJ = 125°C)
0.62
A/pin
TEMPERATURE
TJ-MAX
Junction temperature
−40
150
260
150
°C
°C
°C
Maximum lead temperature (soldering, 10 seconds)(3)
Tstg Storage temperature
–65
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to network ground.
(3) For detailed soldering specifications and information, please refer to DSBGA Wafer Level Chip Scale Package.
6.2 ESD Ratings
VALUE
±2000
±500
UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
Charged-device model (CDM), per JEDEC specification JESD22-C101(2)
V(ESD)
Electrostatic discharge
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
Over operating free-air temperature range (unless otherwise noted).
MIN
MAX
UNIT
INPUT VOLTAGE
VIN_Bx, VANA
Voltage on power connections
Voltage on NRST
2.5
0
5.5
V
V
VANA with 3.6 V
maximum
NRST
Voltage on logic pins (input or output pins)
VANA with 3.6 V
maximum
ENx, nINT
SCL, SDA
0
0
0
V
V
V
Voltage on I2C interface, standard (100 kHz), fast (400 khz),
fast+ (1 MHz), and high-speed (3.4 MHz) modes
Voltage on I2C interface, standard (100 kHz), fast (400 kHz), and
fast+ (1 MHz) modes
1.95
VANA with 3.6 V
maximum
TEMPERATURE
TJ
Junction temperature
Ambient temperature
–40
–40
125
85
°C
°C
TA
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
6.4 Thermal Information
LP8758
THERMAL METRIC(1)
YFF (DSBGA)
UNIT
35 PINS
56.1
0.2
RθJA
Junction-to-ambient thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJCtop
RθJB
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
8.5
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
0.9
ψJB
8.4
RθJCbot
N/A
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.5 Electrical Characteristics
Limits apply over the junction temperature range –40°C ≤ TJ ≤ +125°C, specified V(VANA), VIN , V(NRST), VOUT and IOUT range,
unless otherwise noted. Typical values are at TJ = 25°C, ƒSW = 3 MHz, V(VANA) = VIN = 3.7 V and VOUT = 1 V, unless otherwise
noted.(1)(2)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
EXTERNAL COMPONENTS
CIN
Input filtering capacitance
Connected from VIN_Bx to PGND_Bx
Capacitance per output voltage rail
1.9
10
10
22
µF
µF
Output filtering capacitance,
local
COUT
COUT-
TOTAL
Output capacitance, total
(local and remote)
Total output capacitance
[1-10] MHz
50
10
µF
Input and output capacitor
ESR
ESRC
2
mΩ
0.47
µH
L
Inductor
Inductance of the inductor
–30%
30%
DCRL
Inductor DCR
TDK, VLS252010HBX-R47M
29
mΩ
BUCK REGULATORS
Voltage between VIN_Bx and ground
terminals. VANA must be connected to the
same supply as VIN_Bx.
VIN
Input voltage range
2.5
0.5
3.7
5.5
V
V
Programmable voltage range
Step size, 0.5 V ≤ VOUT < 0.73 V
Step size, 0.73 V ≤ VOUT < 1.4 V
Step size, 1.4 V ≤ VOUT ≤ 3.36 V
1
10
5
3.36
VOUT
Output voltage
mV
20
Output current, VIN ≤ 3 V
ILIM FWD programmed to 5 A per phase.
3(3)
4(3)
Output current, VIN > 3 V, VOUT ≤ 2 V
ILIM FWD programmed to 5 A per phase.
IOUT
Output current
A
V
Output current, VIN > 3 V, VOUT > 2 V
ILIM FWD programmed to 5 A per phase.
3.5(3)
Dropout voltage
VIN – VOUT
0.7
min (–2%,
–20 mV)
max (2%,
20 mV)
DC output voltage
Force PWM mode
accuracy, includes voltage
reference, DC load and line
regulations, process and
temperature
max ( 2%,
20 mV) + 20
mV
PFM mode, the average output voltage
level is increased by a maximum of 20 mV.
min (–2%,
–20 mV)
(1) All voltage values are with respect to network ground.
(2) Minimum (MIN) and maximum (MAX) limits are specified by design, test, or statistical analysis. Typical (TYP) numbers are not verified,
but do represent the most likely norm.
(3) The maximum output current can be limited by the forward current limit, ILIM FWD. The maximum output current is available with 5-A
forward current limit setting.
6
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
Electrical Characteristics (continued)
Limits apply over the junction temperature range –40°C ≤ TJ ≤ +125°C, specified V(VANA), VIN , V(NRST), VOUT and IOUT range,
unless otherwise noted. Typical values are at TJ = 25°C, ƒSW = 3 MHz, V(VANA) = VIN = 3.7 V and VOUT = 1 V, unless otherwise
noted.(1)(2)
PARAMETER
TEST CONDITIONS
PWM mode, L = 0.47 µH
MIN
TYP
10
MAX
UNIT
mVp-p
%/V
Ripple
PFM mode, L = 0.47 µH
IOUT = 1 A
20
DCLNR
DCLDR
DC line regulation
±0.05
DC load regulation in PWM
mode
IOUT from 0 to IOUT(max)
0.3%
±55
Transient load step
response
IOUT = 0 A to 2 A, TR = TF = 400 ns, PWM
mode, COUT = 44 µF, L = 0.47 µH
TLDSR
TLNSR
mV
mV
VIN stepping 3.3 V ↔ 3.8 V, TR = TF = 10
µs, IOUT = IOUT(max)
Transient line response
±15
Programmable range
2.5
5
A
Forward current limit (peak
for every switching cycle),
per phase
Step size
0.5
7.5%
7.5%
2
ILIM FWD
Accuracy, 3 V ≤ VIN ≤ 5.5 V, ILIM FWD = 5 A
Accuracy, 2.5 V ≤ VIN ≤ 3 V, ILIM FWD = 5 A
-5%
-20%
1.6
20%
20%
2.4
ILIM NEG
Negative current limit
A
RDS(ON) HS On-resistance, high-side
Between VIN_Bx and SW_Bx pins (I = 1 A)
40
90
50
mΩ
FET
FET
Between SW_Bx and PGND_Bx pins
(I = 1 A)
RDS(ON) LS On-resistance, low-side
33
< 50
600
mΩ
mV
mA
FET
FET
Overshoot during start-up
Slew-rate = 10 mV/µs
PFM-to-PWM switch -
IPFM-PWM
current threshold(4)
PWM-to-PFM switch -
IPWM-PFM
240
250
–17
mA
current threshold(4)
Output pulldown resistance Regulator disabled
150
–23
350
–10
Ω
Powergood threshold for
interrupt
Rising ramp voltage, enable or voltage
change
BUCKx_INT(BUCKx_SC_I
NT), difference from final
voltage
mV
mV
Falling ramp, voltage change
10
17
23
Powergood threshold for
status signal
BUCKx_STAT(BUCKx_PG 0 during voltage change.
During operation, status signal is forced to
–23
–17
–10
_STAT)
PROTECTION FEATURES
Temperature rising,
CONFIG(TDIE_WARN_LEVEL) = 0
125
105
Thermal warning
Temperature rising,
CONFIG(TDIE_WARN_LEVEL) = 1
°C
°C
Hysteresis
15
150
15
Temperature rising
Hysteresis
Thermal shutdown
Voltage falling
Hysteresis
2.3
2.4
50
2.5
V
VANAUVLO VANA undervoltage lockout
mV
LOAD CURRENT MEASUREMENT
Current measurement
range
Maximum code
LSB
20.46
A
Resolution
20
mA
Measurement accuracy
IOUT ≥ 1 A
< 10%
(4) The final PFM-to-PWM and PWM-to-PFM switchover current varies slightly and is dependant on the output voltage, input voltage and
the magnitude of inductor's ripple current.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
Electrical Characteristics (continued)
Limits apply over the junction temperature range –40°C ≤ TJ ≤ +125°C, specified V(VANA), VIN , V(NRST), VOUT and IOUT range,
unless otherwise noted. Typical values are at TJ = 25°C, ƒSW = 3 MHz, V(VANA) = VIN = 3.7 V and VOUT = 1 V, unless otherwise
noted.(1)(2)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
CURRENT CONSUMPTION
Shutdown current
consumption
V(NRST) = 0 V
1
6
µA
µA
Standby current
consumption, converter
cores disabled
V(NRST) = 1.8 V
Active current consumption
during PFM operation, one V(NRST) = 1.8 V, IOUT = 0 mA, not switching
converter core enabled
55
µA
Active current consumption
during PWM operation, per V(NRST) = 1.8 V, IOUT = 0 mA, L = 0.47 µH
converter core
14.5
mA
DIGITAL INPUT SIGNALS NRST, ENx, SCL, SDA
VIL
VIH
Input low level
Input high level
0.4
V
V
1.2
10
Hysteresis of Schmitt
trigger inputs (SCL, SDA)
VHYS
80
160
mV
ENx pulldown resistance
ENx_PD = 1
350
800
500
720
kΩ
kΩ
NRST pulldown resistance Always present
DIGITAL OUTPUT SIGNALS nINT, SDA
1200
1700
VOL
Output low level
ISOURCE = 2 mA,
0.4
1
V
External pullup resistor for
nINT
RP
To VIO supply
10
kΩ
ALL DIGITAL INPUTS
ILEAK Input current
All logic inputs over pin voltage range
−1
µA
6.6 I2C Serial Bus Timing Requirements
See table notes.(1)(2)
MIN
MAX
UNIT
kHz
Standard mode
Fast mode
100
400
1
kHz
ƒSCL
tLOW
tHIGH
Serial clock frequency
Fast mode +
MHz
MHz
MHz
High-speed mode, Cb = 100 pF
High-speed mode, Cb = 400 pF
Standard mode
3.4
1.7
4.7
1.3
0.5
160
320
4
Fast mode
µs
ns
µs
ns
SCL low time
Fast mode +
High-speed mode, Cb = 100 pF
High-speed mode, Cb = 400 pF
Standard mode
Fast mode
0.6
0.26
60
SCL high time
Fast mode +
High-speed mode, Cb = 100 pF
High-speed mode, Cb = 400 pF
120
(1) See Figure 1 for timing diagram.
(2) Cb refers to the capacitance of one bus line. Cb is expressed in pF units.
8
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
I2C Serial Bus Timing Requirements (continued)
See table notes.(1)(2)
MIN
250
100
50
MAX
UNIT
Standard mode
Fast mode
tSU;DAT
tHD;DAT
tSU;STA
Data setup time
Data hold time
ns
Fast mode +
High-speed mode
Standard mode
10
0
3.45
0.9
Fast mode
0
µs
ns
Fast mode +
0
High-speed mode, Cb = 100 pF
High-speed mode, Cb = 400 pF
Standard mode
0
70
0
150
4.7
0.6
0.26
160
4
Fast mode
µs
ns
µs
ns
µs
Setup time for a start or a
repeated start condition
Fast mode +
High-speed mode
Standard mode
Fast mode
0.6
0.26
160
4.7
1.3
0.5
4
Hold time for a start or a
repeated start condition
tHD;STA
Fast mode +
High-speed mode
Standard mode
Bus free time between a stop
and start condition
tBUF
Fast mode
Fast mode +
Standard mode
Fast mode
0.6
0.26
160
µs
ns
tSU;STO
Setup time for a stop condition
Rise time of SDA signal
Fast mode +
High-speed mode
Standard mode
1000
300
120
80
Fast mode
trDA
tfDA
trCL
trCL1
Fast mode +
ns
ns
ns
ns
High-speed mode, Cb = 100 pF
High-speed mode, Cb = 400 pF
Standard mode
160
250
250
120
80
Fast mode
Fall time of SDA signal
Rise time of SCL signal
Fast mode +
High-speed mode, Cb = 100 pF
High-speed mode, Cb = 400 pF
Standard mode
160
1000
300
120
40
Fast mode
Fast mode +
High-speed Mode, Cb = 100 pF
High-speed Mode, Cb = 400 pF
Standard mode
80
1000
300
120
80
Fast mode
Rise time of SCL signal after a
repeated start condition and
after an acknowledge bit
Fast mode +
High-speed mode, Cb = 100 pF
High-speed mode, Cb = 400 pF
160
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
I2C Serial Bus Timing Requirements (continued)
See table notes.(1)(2)
MIN
MAX
300
300
120
40
UNIT
Standard mode
Fast mode
tfCL
Fall time of a SCL signal
Fast mode +
ns
High-speed mode, Cb = 100 pF
High-speed mode, Cb = 400 pF
80
Capacitive load for each bus
line (SCL and SDA)
Cb
400
50
pF
ns
Pulse width of spike
Fast mode, fast mode +
High-speed mode
suppressed in SCL and SDA
lines (spikes that are less than
the indicated width are
suppressed)
tSP
10
6.7 Switching Characteristics
Limits apply over the junction temperature range –40°C ≤ TJ ≤ +125°C, specified V(VANA), VIN , V(NRST), VOUT and IOUT range,
unless otherwise noted. Typical values are at TJ = 25°C, ƒSW = 3 MHz, V(VANA) = VIN = 3.7 V and VOUT = 1 V, unless otherwise
noted.(1)
PARAMETER
TEST CONDITIONS
OUT ≥ 0.6 V
MIN
2.7
TYP
3
MAX
3.3
UNIT
V
Switching frequency, PWM
mode
ƒSW
MHz
VOUT < 0.6 V
1.8
2
2.2
From ENx to VOUT = 0.225 V (slew-rate
control begins), COUT-TOTAL = 44 µF, no
load
Start-up time (soft start)
140
µs
SLEW_RATEx[2:0] = 000, VOUT ≥ 0.5 V
SLEW_RATEx[2:0] = 001, VOUT ≥ 0.5 V
SLEW_RATEx[2:0] = 010, VOUT ≥ 0.5 V
SLEW_RATEx[2:0] = 011, VOUT ≥ 0.5 V
SLEW_RATEx[2:0] = 100, VOUT ≥ 0.5 V
SLEW_RATEx[2:0] = 101, VOUT ≥ 0.5 V
SLEW_RATEx[2:0] = 110, VOUT ≥ 0.5 V
SLEW_RATEx[2:0] = 111, VOUT ≥ 0.5 V
–15%
–15%
–15%
–15%
–15%
–15%
–15%
–15%
30
15
15%
15%
15%
15%
15%
15%
15%
15%
10
7.5
Output voltage slew-rate(2)
mV/µs
3.8
1.9
0.94
0.40.4
PFM mode (automatically changing to
PWM mode for the measurement)
50
4
Load current measurement
time
µs
PWM mode
(1) Minimum (MIN) and maximum (MAX) limits are specified by design, test, or statistical analysis. Typical (TYP) numbers are not verified,
but do represent the most likely normal.
(2) Specified by design without testing. The slew-rate can be limited by the current limit (forward or negative current limit), output
capacitance, and load current.
10
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
tBUF
SDA
tHD;STA
trCL
tfDA
trDA
tSP
tLOW
tfCL
SCL
tHD;STA
tSU;STA
tSU;STO
tHIGH
tHD;DAT
S
tSU;DAT
S
START
RS
P
START
REPEATED
START
STOP
Figure 1. I2C Timing
6.8 Typical Characteristics
Unless otherwise specified: TA = 25°C, VIN = 3.7 V, ƒSW = 3 MHz, L = 470 nH.
2
1.8
1.6
1.4
1.2
1
8
7.6
7.2
6.8
6.4
6
0.8
0.6
0.4
0.2
0
5.6
5.2
4.8
4.4
4
2.5
3
3.5
4
Input Voltage (V)
4.5
5
5.5
2.5
3
3.5
4
Input Voltage (V)
4.5
5
5.5
D011
D010
V(NRST) = 0 V
V(NRST) = 1.8 V
All converter cores disabled
Figure 2. Shutdown Current Consumption vs Input Voltage
Figure 3. Standby Current Consumption vs Input Voltage
60
18
59
58
57
56
55
54
53
52
51
50
17
16
15
14
2.5
3
3.5
4
Input Voltage (V)
4.5
5
5.5
2.5
3
3.5
4
Input Voltage (V)
4.5
5
5.5
D012
D039
V(NRST) = 1.8 V
Load = 0 mA
VOUT setting = 1000 mV
V(NRST) = 1.8 V
Load = 0 mA
VOUT setting = 1000 mV
Figure 4. PFM Mode Current Consumption vs Input
Voltage —One Output Enabled
Figure 5. PWM Mode Current Consumption vs Input
Voltage — One Output Enable
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
7 Detailed Description
7.1 Overview
The LP8758-xx devices are a family of configurable step-down DC-DC converters with four converter cores. The
LP8758-xx devices are ideally suited for systems powered from 2.5-V to 5.5-V supply voltage. In LP8758-E3 the
cores are configured for a four single-phase configuration. The LP8758-E3 is well suited for space-constrained
applications where high efficiency is required at low output voltages. Typical applications include network
interface cards, modem cards, smart phones and mobile devices, solid-state drives (SSDs), systems-on-a-chip
(SoCs), ASICs, and low power processors.
There are two modes of operation for the converter cores, depending on the output current required: pulse-width
modulation (PWM) and pulse-frequency modulation (PFM). The cores operate in PWM mode at high load
currents of approximately 600 mA or higher. Lighter output current loads cause the converter cores to
automatically switch into PFM mode for reduced current consumption and a longer battery life when forced PWM
mode is disabled. Additional features include soft-start, undervoltage lockout, overload protection, thermal
warning, and thermal shutdown.
7.1.1 Buck Information
The LP8758-E3 has four integrated high-efficiency buck converter cores. The cores are designed for flexibility;
most of the functions are programmable, thus giving a possibility to optimize the regulator operation for each
application.
7.1.1.1 Operating Modes
•
•
•
OFF: Output is isolated from the input voltage rail in this mode. Output has an optional pulldown resistor.
PWM: Converter operates in buck configuration with fixed switching frequency.
PFM: Converter switches only when output voltage decreases below programmed threshold. Inductor current
is discontinuous.
7.1.1.2 Programmability
The following parameters can be programmed through registers:
•
•
•
•
•
Output voltage
Forced PWM operation
Switch current limit
Output voltage slew rate
Enable and disable delays
7.1.1.3 Features
•
•
•
•
•
•
•
•
Dynamic voltage scaling (DVS) support with programmable slew-rate
Automatic mode control based on the loading
Synchronous rectification
Current mode loop with PI compensator
Optional spread spectrum technique to reduce EMI
Soft start
Power-good flag with maskable interrupt
Phase control for optimized EMI: The four cores operate 90° out of phase thereby reducing input ripple
current
•
•
Average output current sensing (for PFM entry and load current measurement)
Voltage sensing from point of the load
12
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
7.2 Functional Block Diagram
VANA
BUCK0
ILIM Detection
nINT
Power-Good Detection
Overload and SC Detection
ILOAD ADC
Interrupts
EN1
EN2
Enable,
Roof/Floor,
Slew-Rate
Control
BUCK1
ILIM Detection
Power-Good Detection
SDA
SCL
I2C
Overload and SC Detection
ILOAD ADC
BUCK2
Registers
OTP EPROM
ILIM Detection
Power-Good Detection
Digital
Logic
Overload and SC Detection
ILOAD ADC
UVLO
Oscillator
NRST
BUCK3
ILIM Detection
Power-Good Detection
Reference
and Bias
Thermal
Monitor
SW
Reset
Overload and SC Detection
ILOAD ADC
7.3 Feature Description
7.3.1 Overview
A block diagram of a single core is shown in Figure 6.
Interleaving switching action of the converters is illustrated in Figure 7. The LP8758-E3 regulator switches each
core 90° apart, reducing input ripple current.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
Feature Description (continued)
High-Side FET
Current Sense
VIN
FB
Positive
Current
Limit
Ramp
Generator
VOUT
œ
SW
Gate
Control
Error
Amp
+
Loop
Comparator
+
Negative
Current
Limit
Power
good
Voltage
Setting Slew
Rate Control
VDAC
œ
Zero
Cross
detect
Low-Side FET
Current Sense
Programmable
Parameters
Master
Interface
Control
Block
GND
Slave
Interface
IADC
Figure 6. Detailed Block Diagram Showing One Core
IL0
IL1
IL2
IL3
0
90
180
270
360
450
540
630
720
PWM0
PWM1
PWM2
PWM3
SWITCHING CYCLE 360º
0
90
180
270
360 450
Phase (Degrees)
540
630
720
(1)
Figure 7. PWM Timings and Inductor Current Waveforms
(1) Graph is not in scale and is for illustrative purposes only.
14 Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
Feature Description (continued)
7.3.1.1 Transition between PWM and PFM Modes
The LP8758-E3 converter cores operate in PWM mode at load current of about 600 mA or higher. At lighter load
current levels the cores automatically switches into PFM mode for reduced current consumption when Forced
PWM mode is disabled (AUTO mode operation). By combining the PFM and the PWM modes a high efficiency is
achieved over a wide output-load current range.
7.3.1.2 Buck Converter Load Current Measurement
Buck load current can be monitored via I2C registers. The monitored buck converter core is selected with the
SEL_I_LOAD.LOAD_CURRENT_BUCK_SELECT[1:0] register bits. A write to this selection register starts a
current measurement sequence. The measurement sequence is typically 50 µs long. The LP8758-E3 device can
be configured to give out an interrupt INT_TOP.I_LOAD_READY after the load current measurement sequence
is finished. Load current measurement interrupt can be masked with TOP_MASK.I_LOAD_READY_MASK bit.
The measurement result can be read from registers I_LOAD_1 and I_LOAD_2. Register I_LOAD_1 bits
BUCK_LOAD_CURRENT[7:0] give out the LSB bits and register I_LOAD_2 bits BUCK_LOAD_CURRENT[9:8]
the MSB bits. The measurement result BUCK_LOAD_CURRENT[9:0] LSB is 20 mA, and maximum value of the
measurement is 20.46 A.
7.3.1.3 Spread-Spectrum Mode
Systems with periodic switching signals may generate a large amount of switching noise in a set of narrowband
frequencies (the switching frequency and its harmonics). The usual solution to reduce noise coupling is to add
EMI-filters and shields to the boards. The register-selectable spread-spectrum mode of the device minimizes the
need for output filters, ferrite beads, or chokes. In spread-spectrum mode, the switching frequency varies
randomly by ±5% about the center frequency, reducing the EMI emissions radiated by the converter and
associated passive components and PCB traces (see Figure 8). This feature is enabled with the
CONFIG.EN_SPREAD_SPEC bit, and it affects all the buck converter cores.
Frequency
Where a fixed frequency converter exhibits large amounts of spectral energy at the switching frequency, the spread
spectrum architecture of the v spreads that energy over a large bandwidth.
Figure 8. Spread-Spectrum Modulation
7.3.2 Power-Up
The power-up sequence for the LP8758-E3 is as follows:
•
•
VANA (and VIN_Bx) reach minimum recommended levels (V(VANA) > VANAUVLO).
NRST is set to high level. This initiates power-on-reset (POR), OTP reading and enables the system I/O
interface. The I2C host must allow at least 1.2 ms before writing or reading data to the LP8758-E3.
•
•
The device enters STANDBY mode.
The host can change the default register setting by I2C if needed.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
Feature Description (continued)
•
One or more of the converter cores can be enabled or disabled by one or more of the ENx pins and by the
I2C interface.
7.3.3 Regulator Control
7.3.3.1 Enabling and Disabling
The buck converter cores can be enabled when the device is in STANDBY or ACTIVE state. There are two ways
to enable and disable the buck converter cores:
•
•
Using BUCKx_CTRL1.EN_BUCKx register bit (when BUCKx_CTRL1.EN_PIN_CTRLx register bit is 0).
Using EN1/2 control pins (BUCKx_CTRL1.EN_BUCKx register bit is 1 and BUCKx_CTRL1.EN_PIN_CTRLx
register bit is 1).
If the EN1/2 control pins are used for enable and disable, the delay from the control signal rising edge to start-up
is set by BUCKx_DELAY.BUCKx_STARTUP_DELAY[3:0] bits and the delay from control signal falling edge to
shutdown is set by BUCKx_DELAY.BUCKx_SHUTDOWN_DELAY[3:0] bits. The delays are valid only for EN1/2
signal and not for control with BUCKx_CTRL1.EN_BUCKx bit. The delay time implemented by EN1/2 has overall
±10% timing accuracy.
The control of the converter cores (with 0 ms delays) is shown in Table 1.
Table 1. Regulator Control
CONTROL
METHOD
BUCKx_CTRL1
EN_PIN_CTRLx
BUCKx_CTRL1
EN_PIN_SELECTx
BUCKx_CTRL1
EN_ROOF_FLOORx
BUCKx
OUTPUT VOLTAGE
ROW
EN_BUCKx
EN1 PIN
EN2 PIN
Enable or
1
2
0
1
Don't Care
0
Don't Care
Don't Care
Don't Care
Don't Care
Don't Care
Don't Care
Don't Care Disabled
disable control
with EN_BUCKx
bit
Don't Care BUCKx_VOUT.BUCKx_VSET[7:0]
Enable or
disable control
with EN1 pin
3
4
1
1
1
1
0
0
0
0
Low
Don't Care Disabled
High
Don't Care BUCKx_VOUT.BUCKx_VSET[7:0]
Enable or
disable control
with EN2 pin
5
6
1
1
1
1
1
1
0
0
Don't Care
Don't Care
Low
Disabled
High
BUCKx_VOUT.BUCKx_VSET[7:0]
Roof or floor
control with EN1
pin
7
1
1
0
1
Low
Don't Care BUCKx_FLOOR_VOUT.BUCKx_F
LOOR_VSET[7:0]
8
9
1
1
1
1
0
1
1
1
High
Don't Care BUCKx_VOUT.BUCKx_VSET[7:0]
Roof or floor
control with EN2
pin
Don't Care
Low
BUCKx_FLOOR_VOUT.BUCKx_F
LOOR_VSET[7:0]
10
1
1
1
1
Don't Care
High
BUCKx_VOUT.BUCKx_VSET[7:0]
The following buck configuration bit settings allows the device to enable or disable the corresponding buck using
the ENx pin:
•
•
•
•
•
BUCKx_CTRL1.EN_BUCKx = 1
BUCKx_CTRL1.EN_PIN_CTRLx = 1
BUCKx_CTRL1.EN_ROOF_FLOORx = 0
BUCKx_VOUT.BUCKx_VSET[7:0] = Required voltage when the ENx pin is high
The enable pin for control is selected with BUCKx_CTRL1.EN_PIN_SELECTx
When the ENx pin is low, Table 1 row 3 (or 5) is valid, and the converter core is disabled. By setting ENx pin
high, Table 1 row 4 (or 6) is valid, and the converter core is enabled with required voltage.
If a converter core is enabled all the time, and the ENx pin controls selection between the two voltage levels,
then the following configuration is used:
•
•
•
•
•
BUCKx_CTRL1.EN_BUCKx = 1
BUCKx_CTRL1.EN_PIN_CTRLx = 1
BUCKx_CTRL1.EN_ROOF_FLOORx = 1
BUCKx_VOUT.BUCKx_VSET[7:0] = Required voltage when the ENx pin is high
The enable pin for control is selected with BUCKx_CTRL1.EN_PIN_SELECTx
16
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
When the ENx pin is low, Table 1 row 7 (or 9) is valid, and the core is enabled with a voltage defined by
BUCKx_FLOOR_VOUT.BUCKx_FLOOR_VSET[7:0] bits. Setting the ENx pin high, Table 1 row 8 (or 10) is valid,
and the core is enabled with a voltage defined by BUCKx_VOUT.BUCKx_VSET[7:0] bits.
If the core is controlled by I2C writings, the BUCKx_CTRL1.EN_PIN_CTRLx bit is set to 0. The enable or disable
is controlled by the BUCKx_CTRL1.EN_BUCKx bit, and when the regulator is enabled, the output voltage is
defined by the BUCKx_VOUT.BUCKx_VSET[7:0] bits. The Table 1 rows 1 and 2 are valid for I2C controlled
operation (ENx pins are ignored).
The buck converter core is enabled by the ENx pin or by I2C writing as shown in Figure 9. The soft-start circuit
limits the in-rush current during start-up. Output voltage increase rate is around 5 mV/μsec during soft-start.
When the output voltage rises to approximately 0.3 V, the output voltage becomes slew-rate controlled. If there is
a short circuit at the output, and the output voltage does not increase above a 0.35-V level in 1 ms, the converter
core is disabled, and interrupt is set. When the output voltage reaches the powergood threshold level the
INT_BUCK_x.BUCKx_PG_INT interrupt flag is set. The powergood interrupt flag can be masked using
BUCK_x_MASK.BUCKx_PG_MASK bit.
The ENx input pins have integrated pull-down resistors. The pull-down resistors are enabled by default and host
can disable those with CONFIG.ENx_PD bits.
Voltage decrease because of load
No new Power-good interrupt
Voltage
BUCKx_VSET[7:0]
Power good
Ramp
SLEW_RATEx[2:0] bit in
BUCKx_CTRL2 register
0.6 V
0.35 V
Time
Resistive pulldown
(if enabled)
Soft start
Enable
BUCKx_STAT bit
(BUCK_x_STAT register)
0
0
0
1
0
0
BUCKx_PG_STAT bit
(BUCK_x_STAT register)
1
1
0
1
BUCKx_PG_INT bit
(INT_BUCK_x register)
0
nINT
Power-good
interrupt
Host clears
interrupt
Figure 9. Converter Core Enable and Disable
7.3.3.2 Changing Output Voltage
The converter core's output voltage can be changed by the ENx pin (voltage levels defined by the BUCKx_VOUT
and BUCKx_FLOOR_VOUT registers) or by writing to the BUCKx_VOUT and BUCKx_FLOOR_VOUT registers.
The voltage change is always slew-rate controlled, and the slew-rate is defined by the
BUCKx_CTRL2.SLEW_RATEx[2:0] bits. During voltage change the Forced PWM mode is used automatically.
When the programmed output voltage is achieved, the mode becomes the one defined by load current, and the
BUCKx_CTRL1.BUCKx_FPWM bit.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
Voltage
BUCKx_VSET
Power-good
Ramp
SLEW_RATEx[2:0] bit
in BUCKx_CTRL2 register
Power-good
BUCKx_FLOOR_VSET
Time
ENx
BUCKx_STAT bit
(BUCKx_STAT register)
1
1
0
BUCKx_PG_STAT bit
(BUCKx_STAT register)
0
1
1
0
1
1
BUCKx_PG_INT bit
(INT_BUCKx register)
0
nINT
Power-good
interrupt
Host clears
interrupt
Power-good
interrupt
Host clears
interrupt
Figure 10. Output Voltage Change
7.3.4 Device Reset Scenarios
There are three reset methods implemented on the LP8758-E3:
•
•
•
Software reset with RESET.SW_RESET register bit;
Reset from low logic level of NRST signal; and
Undervoltage lockout (UVLO) reset from VANA supply.
A SW-reset occurs when RESET.SW_RESET bit is written 1. The bit is automatically cleared after writing. This
event disables all the buck converter cores immediately, resets all the register bits to the default values and OTP
bits are loaded (see Figure 12). I2C interface is not reset during software reset.
If VANA supply voltage falls below UVLO threshold level or NRST signal is set low, then all the converter cores
are disabled immediately, and all the register bits are reset to the default values. When the VANA supply voltage
is above UVLO threshold level and NRST signal rises above threshold level an internal power-on reset (POR)
occurs. OTP bits are loaded to the registers, and a start-up is initiated according to the register settings.
7.3.5 Diagnosis and Protection Features
The LP8758-E3 is capable of providing three levels of protection features:
•
•
•
Warnings for diagnosis which sets interrupt;
Protection events which are disabling one or more converter cores; and
Faults which are causing the device to shutdown.
When the device detects one or more warning or protection conditions, the LP8758-E3 sets the flag bits
indicating what protection or warning conditions have occurred, and the nINT pin is pulled low. nINT is released
again after a clear of flags is complete. The nINT signal stays low until all the pending interrupts are cleared.
When a fault is detected, it is indicated by a INT_TOP.RESET_REG interrupt flag after next start-up.
18
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
EVENT
SNVSBP2 –FEBRUARY 2020
Table 2. Summary of Interrupt Signals
RESULT
No effect
INTERRUPT REGISTER
AND BIT
INTERRUPT MASK
STATUS BIT
RECOVERY /
INTERRUPT CLEAR
Current limit
triggered (20 µs
debounce)
INT_TOP.INT_BUCKx = 1
INT_BUCKx.BUCKx_ILIM_I
NT = 1
BUCKx_MASK.BUCKx_ILI BUCKx_STAT.BUCKx_IL Write 1 to
M_MASK
N/A
IM_STAT
INT_BUCKx.BUCKx_ILI
M_INT bit
Interrupt is not cleared if
current limit is active
Short circuit (VOUT
<
Converter core
INT_TOP.INT_BUCKx = 1
INT_BUCK_0_1.BUCKx_SC
_INT = 1
N/A
Write 1 to
INT_BUCK_0_1.BUCKx_
SC_INT or
0.35 V at 1 ms after disable
enable) or overload
(VOUT decreasing
below 0.35 V during
operation, 1 ms
or
to
INT_BUCK_2_3.BUCKx_SC
_INT = 1
INT_BUCK_2_3.BUCKx_
SC_INTbit
debounce)
Thermal Warning
No effect
INT_TOP.TDIE_WARN = 1 TOP_MASK.TDIE_WARN TOP_STAT.TDIE_WARN Write 1 to
_MASK
_STAT
INT_TOP.TDIE_WARN
bit
Interrupt is not cleared if
temperature is above
thermal warning level
Thermal Shutdown
All converter cores
disabled
INT_TOP.TDIE_SD = 1
N/A
TOP_STAT.TDIE_SD_S Write 1 to
TAT INT_TOP.TDIE_SD bit
Interrupt is not cleared if
temperature is above
thermal shutdown level
Powergood, output
voltage reaches the
programmed value
No effect
No effect
INT_TOP.INT_BUCKx = 1
INT_BUCK_0_1.BUCKx_PG
_INT = 1
BUCK_0_1_MASK.BUCKx BUCK_0_1_STAT.BUCK Write 1 to
_PG_MASK x_PG_STAT INT_BUCK_0_1.BUCKx_
BUCK_2_3_MASK.BUCKx BUCK_2_3_STAT.BUCK PG_INT bit
or
_PG_MASK
x_PG_STAT
or to
INT_BUCK_2_3.BUCKx_PG
_INT = 1
INT_BUCK_2_3.BUCKx_
PG_INT bit
Load current
measurement ready
INT_TOP.I_LOAD_READY TOP_MASK.I_LOAD_REA
= 1 DY_MASK
N/A
Write 1 to
INT_TOP.I_LOAD_REA
DY bit
Start-up (NRST
rising edge)
Device ready for
operation, registers
reset to default values
INT_TOP.RESET_REG = 1 TOP_MASK.RESET_REG
_MASK
N/A
Write 1 to
INT_TOP.RESET_REG
bit
Glitch on supply
voltage and UVLO
triggered (VANA
falling and rising)
Immediate shutdown
followed by powerup,
registers reset to
default values
INT_TOP.RESET_REG = 1 TOP_MASK.RESET_REG
_MASK
N/A
Write 1 to
INT_TOP.RESET_REG
bit
Software requested Immediate shutdown
INT_TOP.RESET_REG = 1 TOP_MASK.RESET_REG
_MASK
N/A
Write 1 to
INT_TOP.RESET_REG
bit
reset
followed by powerup,
registers reset to
default values
7.3.5.1 Warnings for Diagnosis (Interrupt)
7.3.5.1.1 Output Current Limit
The converter cores have programmable output peak current limits. The limits are individually programmed for all
buck converter cores with BUCKx_CTRL2.ILIMx[2:0] bits. If the load current is increased so that the current limit
is triggered, the regulator continues to regulate to the limit current level (current peak regulation). The voltage
may decrease if the load current is higher than limit current. If the current regulation continues for 20 µs, the
LP8758-E3 device sets the INT_BUCKx.BUCKx_ILIM_INT bit and pulls the nINT pin low. The host processor can
read BUCKx_STAT.BUCKx_ILIM_STAT bits to see if the converter cores is still in peak current regulation mode.
For example, if the load on Buck0 output is so high that the output voltage VOUT decreases below a 350-mV
level, the LP8758-E3 device disables the converter core Buck0 and sets the INT_BUCK_0_1.BUCK0_SC_INT
bit. In addition the BUCK_0_1_STAT.BUCK0_STAT bit is set to 0. The interrupt is cleared when the host
processor writes 1 to INT_BUCK_0_1.BUCK0_SC_INT bit. The overload situation is shown in Figure 11.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
Regulator disabled
by digital
New startup if
enable is valid
Voltage
VOUTx
350 mV
Resistive
pulldown
1 ms
Time
Current
ILIMx
Time
25 ms
BUCKx_ILIM_INT bit
(INT_BUCKx register)
0
0
1
1
0
BUCKx_SC_INT bit
(INT_BUCKx register)
1
0
0
1
BUCKx_STAT bit
(BUCKx_STAT register)
nINT
Host clearing the interrupt by writing to flags
Figure 11. Overload Situation
7.3.5.1.2 Thermal Warning
The LP8758-E3 device includes protection features against overtemperature by setting an interrupt for host
processor. The threshold level of the thermal warning is selected with CONFIG.TDIE_WARN_LEVEL bit.
If the LP8758-E3 device temperature increases above the thermal warning level, the device sets
INT_TOP.TDIE_WARN bit and pulls nINT pin low. The status of the thermal warning can be read from
TOP_STAT.TDIE_WARN_STAT bit, and the interrupt is cleared by writing 1 to INT_TOP.TDIE_WARN bit.
7.3.5.2 Protection (Regulator Disable)
If the regulator is disabled because of protection or fault (short-circuit protection, overload protection, thermal
shutdown, or undervoltage lockout), the output power FETs are set to high-impedance mode, and the output
pulldown resistor is enabled (if enabled with the BUCKx_CTRL1.EN_RDISx bits). The turnoff time of the output
voltage is defined by the output capacitance, load current, and the resistance of the integrated pulldown resistor.
7.3.5.2.1 Short-Circuit and Overload Protection
A short-circuit protection feature allows the LP8758-E3 to protect itself and external components against short
circuit at the output or against overload during start-up. The fault threshold is 350 mV, and the protection is
triggered and the converter core is disabled if the output voltage is still below the threshold level 1 ms after the
converter core was enabled.
In a similar way the overload situation is protected during normal operation. If a feedback-pin voltage falls below
0.35 V, and remains below the threshold level for 1 ms, the respective converter core is disabled.
20
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
For example, if the Buck core 0 output is overloaded, then the INT_BUCK_0_1.BUCK0_SC_INT and the
INT_TOP.INT_BUCK0 bits are set to 1, the BUCK_0_1_STAT.BUCK0_STAT bit is set to 0, and the nINT signal
is pulled low. The host processor clears the interrupt by writing 1 to the INT_BUCK_0_1.BUCK0_SC_INT bit. The
regulator makes a new start-up attempt (upon clearing the interrupt) if the enable register bits, ENx control signal,
or both are valid.
7.3.5.2.2 Thermal Shutdown
The LP8758-E3 has an over-temperature protection function that operates to protect itself from short-term
misuse and overload conditions. When the junction temperature exceeds around 150°C, the cores are disabled,
the INT_TOP.TDIE_SD bit is set to 1, the nINT signal is pulled low, and the device enters STANDBY. The nINT
is cleared by writing 1 to the INT_TOP.TDIE_SD bit. If the temperature is above the thermal shutdown level, then
the interrupt is not cleared. The host can read the status of the thermal shutdown from the
TOP_STAT.TDIE_SD_STAT bit. Converter cores cannot be enabled as long as the junction temperature is
above the thermal shutdown level or the thermal shutdown interrupt is pending.
7.3.5.3 Fault (Power Down)
7.3.5.3.1 Undervoltage Lockout
When the input voltage falls below VANAUVLO at the VANA pin, the converter cores are disabled immediately,
and the output capacitors are discharged using the pulldown resistors and the LP8758-E3 device enters
SHUTDOWN. When VANA voltage is above the UVLO threshold level and NRST signal is high, the device
powers up to STANDBY state.
If the reset interrupt is unmasked by default (TOP_MASK.RESET_REG_MASK = 0) the INT_TOP.RESET_REG
interrupt indicates that the device has been in SHUTDOWN. The host processor must clear the interrupt by
writing 1 to the INT_TOP.RESET_REG bit. If the host processor reads the INT_TOP.RESET_REG flag after
detecting an nINT low signal, it knows that the input supply voltage has been below UVLO level (or the host has
requested reset), and the registers are reset to default values.
7.3.6 Digital Signal Filtering
The digital signals have debounce filtering. The signal or supply is sampled with a clock signal and a counter.
This results as an accuracy of one clock period for the debounce window.
Table 3. Digital Signal Filtering
EVENT
SIGNAL / SUPPLY
RISING EDGE LENGTH
FALLING EDGE LENGTH
Enable, disable, or voltage select for
BUCKx
ENx
3 µs(1)
3 µs(1)
VANA undervoltage lockout
Thermal warning
Thermal shutdown
Current limit
VANA
TDIE_WARN
Immediate
20 µs
Immediate
20 µs
TDIE_SD
20 µs
20 µs
VOUTx_ILIM
20 µs
20 µs
Overload
FB_B0, FB_B1, FB_B2, FB_F3
FB_B0, FB_B1, FB_B2, FB_F3
1 ms
1 ms
Power-good
20 µs
20 µs
(1) No glitch filtering, only synchronization.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
7.4 Device Functional Modes
7.4.1 Modes of Operation
SHUTDOWN: The V(NRST) voltage is below threshold level. All switch, reference, control and bias circuitry of the
LP8758-E3 device are turned off.
WAIT-ON: The V(NRST) voltage is above threshold level. The reference and bias circuitry are enabled. The
converter cores of the LP8758-E3 device are turned off.
READ OTP: The main supply voltage V(VANA) is above VANAUVLO level and V(NRST) voltage is above threshold
level. The converter cores are disabled and the reference and bias circuitry of the LP8758-E3 are
enabled. The OTP bits are loaded to registers.
STANDBY: The main supply voltage V(VANA) is above VANAUVLO level and V(NRST) voltage is above threshold
level. The converter cores are disabled and the reference, control and bias circuitry of the LP8758-
E3 are enabled. All registers can be read or written by the host processor through the system serial
interface. The converter cores can be enabled if needed.
ACTIVE:
The main supply voltage V(VANA) is above VANAUVLO level and V(NRST) voltage is above threshold
level. At least one converter core is enabled. All registers can be read or written by the host
processor through the system serial interface.
The operating modes and transitions between the modes are shown in Figure 12.
SHUTDOWN
NRST high
NRST low
From any state except
SHUTDOWN
WAIT-ON
V(VANA) > VANAUVLO
V(VANA) < VANAUVLO
READ
OTP
From any state except
SHUTDOWN
REGISTER
RESET
STANDBY
I2C RESET
REGULATOR
ENABLED
REGULATORS
DISABLED
ACTIVE
Figure 12. Device Operation Modes
22
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
7.5 Programming
7.5.1 I2C-Compatible Interface
The I2C-compatible synchronous serial interface provides access to the programmable functions and registers on
the device. This protocol uses a two-wire interface for bidirectional communications between the devices
connected to the bus. The two interface lines are the Serial Data Line (SDA), and the Serial Clock Line (SCL).
Every device on the bus is assigned a unique address and acts as either a master or a slave depending on
whether it generates or receives the serial clock SCL. The SCL and SDA lines must each have a pullup resistor
placed somewhere on the line and remain HIGH even when the bus is idle. The LP8758-E3 supports standard
mode (100 kHz), fast mode (400 kHz), fast mode plus (1 MHz), and high-speed mode (3.4 MHz).
7.5.1.1 Data Validity
The data on the SDA line must be stable during the HIGH period of the clock signal (SCL). In other words, the
state of the data line can only be changed when clock signal is LOW.
SCL
SDA
data
change
allowed
data
change
allowed
data
change
allowed
data
valid
data
valid
Figure 13. Data Validity Diagram
7.5.1.2 Start and Stop Conditions
The LP8758-E3 is controlled through an I2C-compatible interface. START and STOP conditions classify the
beginning and end of the I2C session. A START condition is defined as SDA transitions from HIGH to LOW while
SCL is HIGH. A STOP condition is defined as SDA transition from LOW to HIGH while SCL is HIGH. The I2C
master always generates the START and STOP conditions.
SDA
SCL
S
P
START
STOP
Condition
Condition
Figure 14. Start and Stop Sequences
The I2C bus is considered busy after a START condition and free after a STOP condition. During data
transmission the I2C master can generate repeated START conditions. A START and a repeated START
condition are equivalent function-wise. The data on SDA must be stable during the HIGH period of the clock
signal (SCL). In other words, the state of SDA can only be changed when SCL is LOW. Figure 15 shows the
SDA and SCL signal timing for the I2C-Compatible Bus. See the I2C Serial Bus Timing Requirements for timing
values.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
Programming (continued)
tBUF
SDA
tHD;STA
trCL
tfDA
trDA
tSP
tLOW
tfCL
SCL
tHD;STA
tSU;STA
tSU;STO
tHIGH
tHD;DAT
S
tSU;DAT
S
RS
P
START
REPEATED
START
STOP
START
Figure 15. I2C-Compatible Timing
7.5.1.3 Transferring Data
Every byte put on the SDA line must be eight bits long, with the most significant bit (MSB) being transferred first.
Each byte of data has to be followed by an acknowledge bit. The acknowledge related clock pulse is generated
by the master. The master releases the SDA line (HIGH) during the acknowledge clock pulse. The LP8758-E3
pulls down the SDA line during the 9th clock pulse, signifying an acknowledge. The LP8758-E3 generates an
acknowledge after each byte has been received.
There is one exception to the acknowledge after every byte rule. When the master is the receiver, it must
indicate to the transmitter an end of data by not-acknowledging (negative acknowledge) the last byte clocked out
of the slave. This negative acknowledge still includes the acknowledge clock pulse (generated by the master),
but the SDA line is not pulled down.
NOTE
If the NRST signal is low during I2C communication the LP8758-E3 device does not
drive SDA line. The ACK signal and data transfer to the master is disabled at that
time.
After the START condition, the bus master sends a chip address. This address is seven bits long followed by an
eighth bit which is a data direction bit (READ or WRITE). For the eighth bit, a 0 indicates a WRITE, and a 1
indicates a READ. The second byte selects the register to which the data is written. The third byte contains data
to write to the selected register.
ACK from slave
ACK from slave
ACK from slave
START MSB Chip Address LSB
W
ACK MSB Register Address LSB ACK
MSB Data LSB
ACK STOP
SCL
SDA
START
id = 0x60
W
ACK
address = 0x40
ACK
address 0x40 data
ACK STOP
Figure 16. Write Cycle (w = write; SDA = 0), id = Device Address = 60Hex for LP8758-E3
24
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
Programming (continued)
ACK from slave
ACK from slave REPEATED START
ACK from slave Data from slave NACK from master
START MSB Chip Address LSB
W
MSB Register Address LSB
RS
MSB Chip Address LSB
R
MSB Data LSB
STOP
SCL
SDA
START
ACK
ACK
ACK
NACK
STOP
id = 0x60
W
address = 0x3F
RS
id = 0x60
R
address 0x3F data
When READ function is to be accomplished, a WRITE function must precede the READ function as shown above.
Figure 17. Read Cycle ( r = read; SDA = 1), id = Device Address = 60Hex for LP8758-E3
7.5.1.4 I2C-Compatible Chip Address
The device address for the LP8758-E3 is 0x60. After the START condition, the I2C master sends the 7-bit
address followed by an eighth bit, read or write (R/W). R/W = 0 indicates a WRITE and R/W = 1 indicates a
READ. The second byte following the device address selects the register address to which the data will be
written. The third byte contains the data for the selected register.
MSB
LSB
1
Bit 7
1
Bit 6
0
Bit 5
0
Bit 4
0
Bit 3
0
Bit 2
0
Bit 1
R/W
Bit 0
2
I C Slave Address (chip address)
Here device address is 110 0000Bin = .
Figure 18. Device Address
7.5.1.5 Auto Increment Feature
The auto-increment feature allows writing several consecutive registers within one transmission. Every time an 8-
bit word is sent to the LP8758-E3, the internal address index counter is incremented by one and the next register
is written. Table 4 below shows writing sequence to two consecutive registers. Note: the auto-increment feature
does not work for read.
Table 4. Auto-Increment Example
Master
Action
Start
Device
Address
= 60H
Write
Register
Address
Data
Data
Stop
LP8758-
E3
ACK
ACK
ACK
ACK
Action
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
7.6 Register Maps
7.6.1 Register Descriptions
The LP8758-E3 is controlled by a set of registers through the serial interface port. The device registers, their
addresses and their abbreviations are listed in Table 5. A more detailed description is given in sections
OTP_REV to I_LOAD_1.
The asterisk (*) marking indicates register bits which are updated from OTP memory during READ OTP state.
Table 5. Summary of LP8758-E3 Control Registers
Read /
Write
Addr
0x01
0x02
Register
D7
D6
D5
D4
D3
D2
D1
D0
OTP_REV
R
OTP_ID[7:0]
BUCK0_
CTRL1
EN_PIN_
CTRL0
EN_PIN_
SELECT0
EN_ROOF
_FLOOR0
BUCK0_
FPWM
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
EN_BUCK0
EN_RDIS0
Reserved
Reserved
BUCK0_
CTRL2
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
Reserved
ILIM0[2:0]
SLEW_RATE0[2:0]
BUCK1_
CTRL1
EN_PIN_
CTRL1
EN_PIN_
SELECT1
EN_ROOF
_FLOOR1
BUCK1_
FPWM
EN_BUCK1
EN_BUCK2
EN_BUCK3
EN_RDIS1
EN_RDIS2
EN_RDIS3
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
BUCK1_
CTRL2
Reserved
ILIM1[2:0]
SLEW_RATE1[2:0]
BUCK2_
CTRL1
EN_PIN_
CTRL2
EN_PIN_
SELECT2
EN_ROOF
_FLOOR2
BUCK2_
FPWM
BUCK2_
CTRL2
Reserved
ILIM2[2:0]
SLEW_RATE2[2:0]
BUCK3_
CTRL1
EN_PIN_
CTRL3
EN_PIN_
SELECT3
EN_ROOF
_FLOOR3
BUCK3_
FPWM
BUCK3_
CTRL2
Reserved
ILIM3[2:0]
SLEW_RATE3[2:0]
BUCK0_
VOUT
BUCK0_VSET[7:0]
BUCK0_
FLOOR_
VOUT
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
0x11
R/W
R/W
R/W
R/W
R/W
R/W
R/W
BUCK0_FLOOR_VSET[7:0]
BUCK1_VSET[7:0]
BUCK1_
VOUT
BUCK1_
FLOOR_
VOUT
BUCK1_FLOOR_VSET[7:0]
BUCK2_VSET[7:0]
BUCK2_
VOUT
BUCK2_
FLOOR_
VOUT
BUCK2_FLOOR_VSET[7:0]
BUCK3_VSET[7:0]
BUCK3_
VOUT
BUCK3_
FLOOR_
VOUT
BUCK3_FLOOR_VSET[7:0]
BUCK0_
DELAY
0x12
0x13
0x14
0x15
0x16
R/W
R/W
R/W
R/W
R/W
BUCK0_SHUTDOWN_DELAY[3:0]
BUCK1_SHUTDOWN_DELAY[3:0]
BUCK2_SHUTDOWN_DELAY[3:0]
BUCK3_SHUTDOWN_DELAY[3:0]
BUCK0_STARTUP_DELAY[3:0]
BUCK1_STARTUP_DELAY[3:0]
BUCK2_STARTUP_DELAY[3:0]
BUCK3_STARTUP_DELAY[3:0]
BUCK1_
DELAY
BUCK2_
DELAY
BUCK3_
DELAY
SW_
RESET
RESET
CONFIG
INT_TOP
Reserved
TDIE
_WARN
_LEVEL
EN_
SPREAD
_SPEC
0x17
0x18
R/W
R/W
Reserved
EN2_PD
EN1_PD
INT_
BUCK3
INT_
INT_
INT_
BUCK0
TDIE_
WARN
RESET_
REG
I_LOAD_
READY
TDIE_SD
BUCK2
BUCK1
26
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
Register Maps (continued)
Table 5. Summary of LP8758-E3 Control Registers (continued)
Read /
Write
Addr
0x19
0x1A
Register
D7
D6
D5
D4
D3
D2
D1
D0
INT_BUCK_
0_1
BUCK1_
PG_INT
BUCK1_
SC_INT
BUCK1_
ILIM_INT
BUCK0_
PG_INT
BUCK0_
SC_INT
BUCK0_
ILIM_INT
R/W
R/W
Reserved
Reserved
Reserved
Reserved
INT_BUCK_
2_3
BUCK3_
PG_INT
BUCK3_
SC_INT
BUCK3_
ILIM_INT
BUCK2_
PG_INT
BUCK2_
SC_INT
BUCK2_
ILIM_INT
TDIE_
WARN_
STAT
TOP_
STAT
TDIE_SD
_STAT
0x1B
R
Reserved
Reserved
BUCK1_
ILIM_
STAT
BUCK0_
ILIM_
STAT
BUCK_0_1_
STAT
BUCK1_
STAT
BUCK1_
PG_STAT
BUCK0_
STAT
BUCK0_
PG_STAT
0x1C
0x1D
0x1E
R
R
Reserved
Reserved
Reserved
Reserved
Reserved
BUCK_2_3_
STAT
BUCK3_
STAT
BUCK3_
PG_STAT
BUCK3_
ILIM_STAT
BUCK2_
STAT
BUCK2_
PG_STAT
BUCK2_
ILIM_STAT
I_LOAD_
READY_
MASK
TOP_
MASK
TDIE_WAR
N_MASK
RESET_
REG_MASK
R/W
BUCK1_
ILIM_
MASK
BUCK0_
ILIM_
MASK
BUCK_0_1_
MASK
BUCK1_
PG_MASK
BUCK0_
PG_MASK
0x1F
R/W
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
BUCK3_
ILIM_
MASK
BUCK2_
ILIM_
MASK
BUCK_2_3_
MASK
BUCK3_
PG_MASK
BUCK2_
PG_MASK
0x20
0x21
R/W
R/W
SEL_I_
LOAD
LOAD_CURRENT_
BUCK_SELECT[1:0]
Reserved
Reserved
BUCK_LOAD_CURRENT[7:0]
BUCK_LOAD_CURRENT[
9:8]
0x22
0x23
I_LOAD_2
I_LOAD_1
R/W
R/W
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
27
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
7.6.1.1 OTP_REV
Address: 0x01
D7
D6
D5
D4
D3
D2
D1
D0
OTP_ID[7:0]
Bits
Field
Type
Default
Description
7:0
OTP_ID[7:0]
R
0xE3 *
Identification code of the OTP EPROM version.
7.6.1.2 BUCK0_CTRL1
Address: 0x02
D7
D6
D5
D4
D3
D2
D1
D0
EN_BUCK0
EN_PIN_
CTRL0
EN_PIN_
SELECT0
EN_ROOF_
FLOOR0
EN_RDIS0
Reserved
BUCK0_FPWM
Reserved
Bits
Field
Type
Default
Description
7
6
5
4
3
EN_BUCK0
EN_PIN_CTRL0
EN_PIN_SELECT0
R/W
1 *
Enable BUCK0 converter core:
0 - BUCK0 converter core is disabled.
1 - BUCK0 converter core is enabled.
R/W
R/W
R/W
R/W
1 *
0 *
0
Enable EN1/2 pin control for BUCK0:
0 - only EN_BUCK0 bit controls BUCK0.
1 - EN_BUCK0 bit AND EN1/2 pin control BUCK0.
Select which ENx pin controls BUCK0 if EN_PIN_CTRL0 = 1:
0 - EN1 pin.
1 - EN2 pin.
EN_ROOF_
FLOOR0
Enable Roof/Floor control of EN1/2 pin if EN_PIN_CTRL0 = 1:
0 - Enable/Disable (1/0) control.
1 - Roof/Floor (1/0) control.
EN_RDIS0
1
Enable output discharge resistor when BUCK0 is disabled:
0 - Discharge resistor disabled.
1 - Discharge resistor enabled.
2
1
Reserved
R/W
R/W
0
BUCK0_FPWM
1 *
Forces the BUCK0 converter core to operate in PWM mode:
0 - Automatic transitions between PFM and PWM modes (AUTO mode).
1 - Forced to PWM operation.
0
Reserved
R/W
0
7.6.1.3 BUCK0_CTRL2
Address: 0x03
D7
D6
D5
D4
D3
D2
D1
D0
Reserved
ILIM0[2:0]
SLEW_RATE0[2:0]
Bits
7:6
Field
Type
R/W
R/W
Default
00
Description
Reserved
ILIM0[2:0]
5:3
0x6 *
Sets the switch current limit of BUCK0. Can be programmed at any time during
operation:
0x2 - 2.5 A
0x3 - 3.0 A
0x4 - 3.5 A
0x5 - 4.0 A
0x6 - 4.5 A
0x7 - 5.0 A
28
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
Bits
SNVSBP2 –FEBRUARY 2020
Field
Type
Default
Description
2:0 SLEW_RATE0[2:0]
R/W
0x2 *
Sets the output voltage slew rate for BUCK0 converter core (rising and falling edges):
0x0 - 30 mV/µs
0x1 - 15 mV/µs
0x2 - 10 mV/µs
0x3 - 7.5 mV/µs
0x4 - 3.8 mV/µs
0x5 - 1.9 mV/µs
0x6 - 0.94 mV/µs
0x7 - 0.4 mV/µs
7.6.1.4 BUCK1_CTRL1
Address: 0x04
D7
D6
D5
D4
D3
D2
D1
D0
EN_BUCK1
EN_PIN_
CTRL1
EN_PIN_
SELECT1
EN_ROOF_
FLOOR1
EN_RDIS1
Reserved
BUCK1_FPWM
Reserved
Bits
Field
Type
Default
Description
7
6
5
4
3
EN_BUCK1
EN_PIN_CTRL1
EN_PIN_SELECT1
R/W
1 *
Enable BUCK1 converter core:
0 - BUCK1 converter core is disabled.
1 - BUCK1 converter core is enabled.
R/W
R/W
R/W
R/W
1 *
0 *
0
Enable EN1/2 pin control for BUCK1:
0 - only EN_BUCK1 bit controls BUCK1.
1 - EN_BUCK1 bit AND EN1/2 pin control BUCK1.
Select which ENx pin controls BUCK1 if EN_PIN_CTRL1 = 1:
0 - EN1 pin
1 - EN2 pin.
EN_ROOF_
FLOOR1
Enable Roof/Floor control of EN1/2 pin if EN_PIN_CTRL1 = 1:
0 - Enable/Disable (1/0) control.
1 - Roof/Floor (1/0) control.
EN_RDIS1
1
Enable output discharge resistor when BUCK1 is disabled:
0 - Discharge resistor is disabled.
1 - Discharge resistor is enabled.
2
1
Reserved
R/W
R/W
0
BUCK1_FPWM
1 *
Forces the BUCK1 converter core to operate in PWM mode:
0 - Automatic transitions between PFM and PWM modes (AUTO mode).
1 - Forced to PWM operation.
0
Reserved
R/W
0
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
29
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
7.6.1.5 BUCK1_CTRL2
Address: 0x05
D7
D6
D5
D4
D3
D2
D1
D0
Reserved
ILIM1[2:0]
SLEW_RATE1[2:0]
Bits
7:6
Field
Type
R/W
R/W
Default
00
Description
Reserved
ILIM1[2:0]
5:3
0x3 *
Sets the switch current limit of BUCK1. Can be programmed at any time during
operation:
0x2 - 2.5 A
0x3 - 3.0 A
0x4 - 3.5 A
0x5 - 4.0 A
0x6 - 4.5 A
0x7 - 5.0 A
2:0 SLEW_RATE1[2:0]
R/W
0x2 *
Sets the output voltage slew rate for BUCK1 converter core (rising and falling edges):
0x0 - 30 mV/µs
0x1 - 15 mV/µs
0x2 - 10 mV/µs
0x3 - 7.5 mV/µs
0x4 - 3.8 mV/µs
0x5 - 1.9 mV/µs
0x6 - 0.94 mV/µs
0x7 - 0.4 mV/µs
7.6.1.6 BUCK2_CTRL1
Address: 0x06
D7
D6
D5
D4
D3
D2
D1
D0
EN_BUCK2
EN_PIN_
CTRL2
EN_PIN_
SELECT2
EN_ROOF_
FLOOR2
EN_RDIS2
Reserved
BUCK2_FPWM
Reserved
Bits
Field
Type
Default
Description
7
6
5
4
3
EN_BUCK2
EN_PIN_CTRL2
EN_PIN_SELECT2
R/W
1 *
Enable BUCK2 converter core:
0 - BUCK2 converter core is disabled.
1 - BUCK2 converter core is enabled.
R/W
R/W
R/W
R/W
1 *
0 *
0
Enable EN1/2 pin control for BUCK2:
0 - only EN_BUCK2 bit controls BUCK2.
1 - EN_BUCK2 bit AND EN1/2 pin control BUCK2.
Select which ENx pin controls BUCK2 if EN_PIN_CTRL2 = 1:
0 - EN1 pin
1 - EN2 pin.
EN_ROOF_
FLOOR2
Enable Roof/Floor control of EN1/2 pin if EN_PIN_CTRL2 = 1:
0 - Enable/Disable (1/0) control.
1 - Roof/Floor (1/0) control.
EN_RDIS2
1
Enable output discharge resistor when BUCK2 is disabled:
0 - Discharge resistor is disabled.
1 - Discharge resistor is enabled.
2
1
Reserved
R/W
R/W
0
BUCK2_FPWM
1 *
Forces the BUCK2 converter core to operate in PWM mode:
0 - Automatic transitions between PFM and PWM modes (AUTO mode).
1 - Forced to PWM operation.
0
Reserved
R/W
0
30
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
7.6.1.7 BUCK2_CTRL2
Address: 0x07
D7
D6
D5
D4
D3
D2
D1
SLEW_RATE2[2:0]
D0
Reserved
ILIM2[2:0]
Bits
7:6
Field
Type
R/W
R/W
Default
00
Description
Reserved
ILIM2[2:0]
5:3
0x3 *
Sets the switch current limit of BUCK2. Can be programmed at any time during
operation:
0x2 - 2.5 A
0x3 - 3.0 A
0x4 - 3.5 A
0x5 - 4.0 A
0x6 - 4.5 A
0x7 - 5.0 A
2:0 SLEW_RATE2[2:0]
R/W
0x2 *
Sets the output voltage slew rate for BUCK2 converter core (rising and falling edges):
0x0 - 30 mV/µs
0x1 - 15 mV/µs
0x2 - 10 mV/µs
0x3 - 7.5 mV/µs
0x4 - 3.8 mV/µs
0x5 - 1.9 mV/µs
0x6 - 0.94 mV/µs
0x7 - 0.4 mV/µs
7.6.1.8 BUCK3_CTRL1
Address: 0x08
D7
D6
D5
D4
D3
D2
D1
D0
EN_BUCK3
EN_PIN_
CTRL3
EN_PIN_
SELECT3
EN_ROOF_
FLOOR3
EN_RDIS3
Reserved
BUCK3_FPWM
Reserved
Bits
Field
Type
Default
Description
7
6
5
4
3
EN_BUCK3
EN_PIN_CTRL3
EN_PIN_SELECT3
R/W
1 *
Enable BUCK3 converter core:
0 - BUCK3 converter core is disabled.
1 - BUCK3 converter core is enabled.
R/W
R/W
R/W
R/W
1 *
0 *
0
Enable EN1/2 pin control for BUCK3:
0 - only EN_BUCK3 bit controls BUCK3
1 - EN_BUCK3 bit AND EN1/2 pin control BUCK3.
Select which ENx pin controls BUCK3 if EN_PIN_CTRL3 = 1:
0 - EN1 pin
1 - EN2 pin.
EN_ROOF_
FLOOR3
Enable Roof/Floor control of EN1/2 pin if EN_PIN_CTRL3 = 1:
0 - Enable/Disable (1/0) control
1 - Roof/Floor (1/0) control.
EN_RDIS3
1
Enable output discharge resistor when BUCK3 is disabled:
0 - Discharge resistor is disabled.
1 - Discharge resistor is enabled.
2
1
Reserved
R/W
R/W
0
BUCK3_FPWM
1 *
Forces the BUCK3 converter core to operate in PWM mode:
0 - Automatic transitions between PFM and PWM modes (AUTO mode).
1 - Forced to PWM operation.
0
Reserved
R/W
0
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
31
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
7.6.1.9 BUCK3_CTRL2
Address: 0x09
D7
D6
D5
D4
D3
D2
D1
D0
Reserved
ILIM3[2:0]
SLEW_RATE3[2:0]
Bits
7:6
Field
Type
R/W
R/W
Default
00
Description
Reserved
ILIM3[2:0]
5:3
0x5 *
Sets the switch current limit of BUCK3. Can be programmed at any time during
operation:
0x2 - 2.5 A
0x3 - 3.0 A
0x4 - 3.5 A
0x5 - 4.0 A
0x6 - 4.5 A
0x7 - 5.0 A
2:0 SLEW_RATE3[2:0]
R/W
0x2 *
Sets the output voltage slew rate for BUCK3 converter core (rising and falling edges):
0x0 - 30 mV/µs
0x1 - 15 mV/µs
0x2 - 10 mV/µs
0x3 - 7.5 mV/µs
0x4 - 3.8 mV/µs
0x5 - 1.9 mV/µs
0x6 - 0.94 mV/µs
0x7 - 0.4 mV/µs
7.6.1.10 BUCK0_VOUT
Address: 0x0A
D7
D6
D5
D4
D3
D2
D1
D0
BUCK0_VSET[7:0]
Bits
Field
Type
Default
Description
7:0 BUCK0_VSET[7:0]
R/W
0x39 *
Sets the output voltage of BUCK0 converter core (Default 900 mV)
0.5 V - 0.73 V, 10 mV steps
0x00 - 0.5 V
...
0x17 - 0.73 V
0.73 V - 1.4 V, 5 mV steps
0x18 - 0.735 V
...
0x9D - 1.4 V
1.4 V - 3.36 V, 20 mV steps
0x9E - 1.42 V
...
0xFF - 3.36 V
32
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
7.6.1.11 BUCK0_FLOOR_VOUT
Address: 0x0B
D7
D6
D5
D4
D3
D2
D1
D0
BUCK0_FLOOR_VSET[7:0]
Bits
Field
Type
Default
Description
7:0 BUCK0_FLOOR_VSET[
7:0]
R/W
0x00
Sets the output voltage of BUCK0 converter core when Floor state is used:
0.5 V - 0.73 V, 10 mV steps
0x00 - 0.5 V
...
0x17 - 0.73 V
0.73 V - 1.4 V, 5 mV steps
0x18 - 0.735 V
...
0x9D - 1.4 V
1.4 V - 3.36 V, 20 mV steps
0x9E - 1.42 V
...
0xFF - 3.36 V
7.6.1.12 BUCK1_VOUT
Address: 0x0C
D7
D6
D5
D4
D3
D2
D1
D0
BUCK1_VSET[7:0]
Bits
Field
BUCK1_VSET[7:0]
Type
R/W
Default
0x75 *
Description
7:0
Sets the output voltage of BUCK1 converter core (Default 1200 mV):
0.5 V - 0.73 V, 10 mV steps
0x00 - 0.5 V
...
0x17 - 0.73 V
0.73 V - 1.4 V, 5 mV steps
0x18 - 0.735 V
...
0x9D - 1.4 V
1.4 V - 3.36 V, 20 mV steps
0x9E - 1.42 V
...
0xFF - 3.36 V
7.6.1.13 BUCK1_FLOOR_VOUT
Address: 0x0D
D7
D6
D5
D4
D3
D2
D1
D0
BUCK1_FLOOR_VSET[7:0]
Bits
Field
Type
R/W
Default
0x00
Description
7:0 BUCK1_FLOOR_VSET[7:0]
Sets the output voltage of BUCK1 converter core when the Floor state is
used:
0.5 V - 0.73 V, 10 mV steps
0x00 - 0.5V
...
0x17 - 0.73 V
0.73 V - 1.4 V, 5 mV steps
0x18 - 0.735 V
...
0x9D - 1.4 V
1.4 V - 3.36 V, 20 mV steps
0x9E - 1.42 V
...
0xFF - 3.36 V
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
33
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
7.6.1.14 BUCK2_VOUT
Address: 0x0E
D7
D6
D5
D4
D3
D2
D1
D0
BUCK2_VSET[7:0]
Bits
Field
Type
Default
Description
7:0 BUCK2_VSET[7:0]
R/W
0xB1 *
Sets the output voltage of BUCK2 converter core (Default 1800 mV):
0.5 V - 0.73 V, 10 mV steps
0x00 - 0.5V
...
0x17 - 0.73 V
0.73 V - 1.4 V, 5 mV steps
0x18 - 0.735 V
...
0x9D - 1.4 V
1.4 V - 3.36 V, 20 mV steps
0x9E - 1.42 V
...
0xFF - 3.36 V
7.6.1.15 BUCK2_FLOOR_VOUT
Address: 0x0F
D7
D6
D5
D4
BUCK2_FLOOR
_VSET[7:0]
D3
D2
D1
D0
Bits
Field
Type
Default
Description
7:0
BUCK2_FLOOR
_VSET[7:0]
R/W
0x00
Sets the output voltage of BUCK2 converter core when the Floor state is used:
0.5 V - 0.73 V, 10 mV steps
0x00 - 0.5 V
...
0x17 - 0.73 V
0.73 V - 1.4 V, 5 mV steps
0x18 - 0.735 V
...
0x9D - 1.4 V
1.4 V - 3.36 V, 20 mV steps
0x9E - 1.42 V
...
0xFF - 3.36 V
7.6.1.16 BUCK3_VOUT
Address: 0x10
D7
D6
D5
D4
D3
D2
D1
D0
BUCK3_VSET[7:0]
Bits
Field
Type
Default
Description
7:0 BUCK3_VSET[7:0]
R/W
0xDE *
Sets the output voltage of BUCK3 converter core (Default 2700 mV)
0.5 V - 0.73 V, 10 mV steps
0x00 - 0.5 V
...
0x17 - 0.73 V
0.73 V - 1.4 V, 5 mV steps
0x18 - 0.735 V
...
0x9D - 1.4 V
1.4 V - 3.36 V, 20 mV steps
0x9E - 1.42 V
...
0xFF - 3.36 V
34
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
7.6.1.17 BUCK3_FLOOR_VOUT
Address: 0x11
D7
D6
D5
D4
BUCK3_FLOOR
_VSET[7:0]
D3
D2
D1
D0
Bits
Field
Type
Default
Description
7:0
BUCK3_FLOOR
_VSET[7:0]
R/W
0x00
Sets the output voltage of BUCK3 converter core when Floor state is used:
0.5 V - 0.73 V, 10 mV steps
0x00 - 0.5 V
...
0x17 - 0.73 V
0.73 V - 1.4 V, 5 mV steps
0x18 - 0.735 V
...
0x9D - 1.4 V
1.4 V - 3.36 V, 20 mV steps
0x9E - 1.42 V
...
0xFF - 3.36 V
7.6.1.18 BUCK0_DELAY
Address: 0x12
D7
D6
D5
D4
D3
D2
D1
D0
BUCK0_SHUTDOWN_DELAY[3:0]
BUCK0_STARTUP_DELAY[3:0]
Bits
Field
Type
Default
Description
7:4
BUCK0_
SHUTDOWN_
DELAY[3:0]
R/W
0x0 *
Shutdown delay of BUCK0 from falling edge of the ENx signal:
0x0 - 0 ms
0x1 - 1 ms
...
0xF - 15 ms
3:0
BUCK0_
STARTUP_
DELAY[3:0]
R/W
0x2 *
Startup delay of BUCK0 from rising edge of the ENx signal:
0x0 - 0 ms
0x1 - 1 ms
...
0xF - 15 ms
7.6.1.19 BUCK1_DELAY
Address: 0x13
D7
D6
D5
D4
D3
D2
D1
D0
BUCK1_SHUTDOWN_DELAY[3:0]
BUCK1_STARTUP_DELAY[3:0]
Bits
Field
Type
Default
Description
7:4
BUCK1_
SHUTDOWN_
DELAY[3:0]
R/W
0x0 *
Shutdown delay of BUCK1 from falling edge of the ENx signal:
0x0 - 0 ms
0x1 - 1 ms
...
0xF - 15 ms
3:0
BUCK1_
STARTUP_
DELAY[3:0]
R/W
0x3 *
Startup delay of BUCK1 from rising edge of the ENx signal:
0x0 - 0 ms
0x1 - 1 ms
...
0xF - 15 ms
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
35
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
7.6.1.20 BUCK2_DELAY
Address: 0x14
D7
D6
D5
D4
D3
D2
D1
D0
BUCK2_SHUTDOWN_DELAY[3:0]
BUCK2_STARTUP_DELAY[3:0]
Bits
Field
Type
Default
Description
7:4
BUCK2_
SHUTDOWN_
DELAY[3:0]
R/W
0x0 *
Shutdown delay of BUCK2 from falling edge of the ENx signal:
0x0 - 0 ms
0x1 - 1 ms
...
0xF - 15 ms
3:0
BUCK2_
STARTUP_
DELAY[3:0]
R/W
0x3 *
Start-up delay of BUCK2 from rising edge of the ENx signal:
0x0 - 0 ms
0x1 - 1 ms
...
0xF - 15 ms
7.6.1.21 BUCK3_DELAY
Address: 0x15
D7
D6
D5
D4
D3
D2
D1
D0
BUCK3_SHUTDOWN_DELAY[3:0]
BUCK3_STARTUP_DELAY[3:0]
Bits
Field
Type
Default
Description
7:4
BUCK3_
SHUTDOWN_
DELAY[3:0]
R/W
0x0 *
Shutdown delay of BUCK3 from falling edge of the ENx signal:
0x0 - 0 ms
0x1 - 1 ms
...
0xF - 15 ms
3:0
BUCK3_
STARTUP_
DELAY[3:0]
R/W
0x4 *
Start-up delay of BUCK3 from rising edge of the ENx signal:
0x0 - 0 ms
0x1 - 1 ms
...
0xF - 15 ms
7.6.1.22 RESET
Address: 0x16
D7
D6
D5
D4
D3
D2
D1
D0
Reserved
SW_RESET
Bits
7:1
0
Field
Type
R/W
R/W
Default
0000 000
0
Description
Reserved
SW_RESET
Software commanded reset. When written to 1, the registers are reset to default
values, OTP memory is read, and the I2C interface is reset.
The bit is automatically cleared.
36
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
7.6.1.23 CONFIG
Address: 0x17
D7
D6
D5
D4
D3
D2
D1
EN1_PD
D0
Reserved
TDIE_WARN_
LEVEL
EN2_PD
EN_SPREAD
_SPEC
Bits
Field
Type
R/W
R/W
Default
0000
0
Description
7:4
3
Reserved
TDIE_WARN_LEVEL
Thermal warning threshold level.
0 - 125°C
1 - 105°C
2
1
0
EN2_PD
R/W
R/W
R/W
1
1
0
Selects the pulldown resistor on the EN2 input pin.
0 - Pulldown resistor is disabled.
1 - Pulldown resistor is enabled.
EN1_PD
Selects the pull down resistor on the EN1 input pin.
0 - Pulldown resistor is disabled.
1 - Pulldown resistor is enabled.
EN_SPREAD_SPEC
Enable spread-spectrum feature:
0 - Disabled
1 - Enabled
7.6.1.24 INT_TOP
Address: 0x18
D7
D6
INT_BUCK2
D5
D4
D3
D2
D1
D0
INT_BUCK3
INT_BUCK1
INT_BUCK0
TDIE_SD
TDIE_WARN
RESET_REG
I_LOAD_
READY
Bits
Field
Type
Default
Description
7
6
5
4
3
INT_BUCK3
INT_BUCK2
INT_BUCK1
INT_BUCK0
TDIE_SD
R
0
Interrupt indicating that output BUCK3 has a pending interrupt. The reason for the
interrupt is indicated in INT_BUCK3 register.
This bit is cleared automatically when INT_BUCK3 register is cleared to 0x00.
R
R
0
0
0
0
Interrupt indicating that output BUCK2 has a pending interrupt. The reason for the
interrupt is indicated in INT_BUCK2 register.
This bit is cleared automatically when INT_BUCK2 register is cleared to 0x00.
Interrupt indicating that output BUCK1 has a pending interrupt. The reason for the
interrupt is indicated in INT_BUCK1 register.
This bit is cleared automatically when INT_BUCK1 register is cleared to 0x00.
R
Interrupt indicating that output BUCK0 has a pending interrupt. The reason for the
interrupt is indicated in INT_BUCK0 register.
This bit is cleared automatically when INT_BUCK0 register is cleared to 0x00.
R/W
Latched status bit indicating that the die junction temperature has exceeded the
thermal shutdown level. The converter cores have been disabled if they were enabled.
The converter cores cannot be enabled if this bit is active. The actual status of the
thermal warning is indicated by the TOP_STAT.TDIE_SD_STAT bit.
Write 1 to clear interrupt.
2
1
TDIE_WARN
RESET_REG
R/W
R/W
0
0
Latched status bit indicating that the die junction temperature has exceeded the
thermal warning level. The actual status of the thermal warning is indicated by
TOP_STAT.TDIE_WARN_STAT bit.
Write 1 to clear interrupt.
Latched status bit indicating that either startup (NRST rising edge) has done, VANA
supply voltage has been below undervoltage threshold level or the host has requested
a reset (RESET.SW_RESET). The converter cores have been disabled, and registers
are reset to default values and the normal startup procedure is done.
Write 1 to clear interrupt.
0
I_LOAD_READY
R/W
0
Latched status bit indicating that the load current measurement result is available in
I_LOAD_1 and I_LOAD_2 registers.
Write 1 to clear interrupt.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
37
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
7.6.1.25 INT_BUCK_0_1
Address: 0x19
D7
D6
D5
D4
D3
D2
D1
D0
Reserved
BUCK1_PG
_INT
BUCK1_SC
_INT
BUCK1_ILIM
_INT
Reserved
BUCK0_PG
_INT
BUCK0_SC
_INT
BUCK0_ILIM
_INT
Bits
Field
Type
R/W
R/W
Default
Description
7
6
Reserved
0
0
BUCK1_PG_INT
Latched status bit indicating that BUCK1 output voltage has reached power-good
threshold level.
Write 1 to clear.
5
4
BUCK1_SC_INT
BUCK1_ILIM_INT
R/W
R/W
0
0
Latched status bit indicating that the BUCK1 output voltage has fallen below 0.35-V
level during operation or BUCK1 output didn't reach 0.35-V level in 1 ms from enable.
Write 1 to clear.
Latched status bit indicating that output current limit has been active.
Write 1 to clear.
3
2
Reserved
R/W
R/W
0
0
BUCK0_PG_INT
Latched status bit indicating that BUCK0 output voltage has reached powergood
threshold level.
Write 1 to clear.
1
0
BUCK0_SC_INT
BUCK0_ILIM_INT
R/W
R/W
0
0
Latched status bit indicating that the BUCK0 output voltage has fallen below 0.35-V
level during operation or BUCK0 output didn't reach 0.35-V level in 1 ms from enable.
Write 1 to clear.
Latched status bit indicating that output current limit has been active.
Write 1 to clear.
7.6.1.26 INT_BUCK_2_3
Address: 0x1A
D7
D6
D5
D4
D3
D2
D1
D0
Reserved
BUCK3_PG
_INT
BUCK3_SC
_INT
BUCK3_ILIM
_INT
Reserved
BUCK2_PG
_INT
BUCK2_SC
_INT
BUCK2_ILIM
_INT
Bits
Field
Type
R/W
R/W
Default
Description
7
6
Reserved
0
0
BUCK3_PG_INT
Latched status bit indicating that BUCK3 output voltage has reached power-good
threshold level.
Write 1 to clear.
5
4
BUCK3_SC_INT
BUCK3_ILIM_INT
R/W
R/W
0
0
Latched status bit indicating that the BUCK3 output voltage has fallen below 0.35-V
level during operation or BUCK3 output didn't reach 0.35-V level in 1 ms from enable.
Write 1 to clear.
Latched status bit indicating that output current limit has been active.
Write 1 to clear.
3
2
Reserved
R/W
R/W
0
0
BUCK2_PG_INT
Latched status bit indicating that BUCK2 output voltage has reached powergood
threshold level.
Write 1 to clear.
1
0
BUCK2_SC_INT
BUCK2_ILIM_INT
R/W
R/W
0
0
Latched status bit indicating that the BUCK2 output voltage has fallen below 0.35 V
level during operation or BUCK2 output didn't reach 0.35-V level in 1 ms from enable.
Write 1 to clear.
Latched status bit indicating that output current limit has been active.
Write 1 to clear.
38
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
7.6.1.27 TOP_STAT
Address: 0x1B
D7
D6
D5
D4
D3
D2
D1
D0
Reserved
TDIE_SD
_STAT
TDIE_WARN
_STAT
Reserved
Bits
7:4
3
Field
Type
R
Default
0000
0
Description
Reserved
TDIE_SD_STAT
R
Status bit indicating the status of thermal shutdown:
0 - Die temperature below the thermal shutdown level.
1 - Die temperature above the thermal shutdown level.
2
TDIE_WARN
_STAT
R
R
0
Status bit indicating the status of thermal warning:
0 - Die temperature below the thermal warning level.
1 - Die temperature above the thermal warning level.
1:0
Reserved
00
7.6.1.28 BUCK_0_1_STAT
Address: 0x1C
D7
D6
D5
D4
D3
D2
D1
D0
BUCK1_STAT
BUCK1_PG
_STAT
Reserved
BUCK1_ILIM
_STAT
BUCK0_STAT
BUCK0_PG
_STAT
Reserved
BUCK0_ILIM
_STAT
Bits
Field
Type
Default
Description
7
BUCK1_STAT
BUCK1_PG_STAT
Reserved
R
0
Status bit indicating the enable or disable status of BUCK1:
0 - BUCK1 converter core is disabled.
1 - BUCK1 converter core is enabled.
6
R
0
Status bit indicating BUCK1 output voltage validity (raw status):
0 - BUCK1 output is above power-good threshold level
1 - BUCK1 output is below power-good threshold level.
5
4
R
R
0
0
BUCK1_ILIM
_STAT
Status bit indicating BUCK1 current limit status (raw status):
0 - BUCK1 output current is below current limit level.
1 - BUCK1 output current limit is active.
3
2
BUCK0_STAT
BUCK0_PG_STAT
Reserved
R
R
0
0
Status bit indicating the enable or disable status of BUCK0:
0 - BUCK0 converter core is disabled.
1 - BUCK0 converter core is enabled.
Status bit indicating BUCK0 output voltage validity (raw status):
0 - BUCK0 output is above the power-good threshold level.
1 - BUCK0 output is below the power-good threshold level.
1
0
R
R
0
0
BUCK0_ILIM
_STAT
Status bit indicating BUCK0 current limit status (raw status):
0 - BUCK0 output current is below the current limit level.
1 - BUCK0 output current limit is active.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
39
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
7.6.1.29 BUCK_2_3_STAT
Address: 0x1D
D7
D6
D5
D4
D3
D2
D1
D0
BUCK3_STAT
BUCK3_PG
_STAT
Reserved
BUCK3_ILIM
_STAT
BUCK2_STAT
BUCK2_PG
_STAT
Reserved
BUCK2_ILIM
_STAT
Bits
Field
Type
Default
Description
7
BUCK3_STAT
BUCK3_PG_STAT
Reserved
R
0
Status bit indicating the enable or disable status of BUCK3:
0 - BUCK3 converter core is disabled.
1 - BUCK3 converter core is enabled.
6
R
0
Status bit indicating BUCK3 output voltage validity (raw status):
0 - BUCK3 output is above power-good threshold level.
1 - BUCK3 output is below power-good threshold level.
5
4
R
R
0
0
BUCK3_ILIM
_STAT
Status bit indicating BUCK3 current limit status (raw status):
0 - BUCK3 output current is below current limit level.
1 - BUCK3 output current limit is active.
3
2
BUCK2_STAT
BUCK2_PG_STAT
Reserved
R
R
0
0
Status bit indicating the enable or disable status of BUCK2:
0 - BUCK2 converter core is disabled.
1 - BUCK2 converter core is enabled.
Status bit indicating BUCK2 output voltage validity (raw status):
0 - BUCK2 output is above power-good threshold level.
1 - BUCK2 output is below power-good threshold level.
1
0
R
R
0
0
BUCK2_ILIM
_STAT
Status bit indicating BUCK2 current limit status (raw status):
0 - BUCK2 output current is below current limit level.
1 - BUCK2 output current limit is active.
7.6.1.30 TOP_MASK
Address: 0x1E
D7
D6
D5
D4
D3
D2
D1
D0
Reserved
TDIE_WARN
_MASK
RESET_REG
_MASK
I_LOAD_
READY_MASK
Bits
7:3
2
Field
Type
R/W
R/W
Default
0000 0
0 *
Description
Reserved
TDIE_WARN
_MASK
Masking for thermal warning interrupt INT_TOP.TDIE_WARN:
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect TOP_STAT.TDIE_WARN_STAT status bit.
1
0
RESET_REG
_MASK
R/W
R/W
1 *
0 *
Masking for register reset interrupt INT_TOP.RESET_REG:
0 - Interrupt is generated.
1 - Interrupt is not generated.
I_LOAD_
READY_MASK
Masking for load current measurement ready interrupt INT_TOP.I_LOAD_READY:
0 - Interrupt is generated.
1 - Interrupt is not generated.
40
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
7.6.1.31 BUCK_0_1_MASK
Address: 0x1F
D7
D6
D5
D4
D3
D2
D1
Reserved
D0
Reserved
BUCK1_PG
_MASK
Reserved
BUCK1_ILIM
_MASK
Reserved
BUCK0_PG
_MASK
BUCK0_ILIM
_MASK
Bits
Field
Type
R/W
R/W
Default
Description
7
6
Reserved
0
BUCK1_PG_MASK
1 *
Masking for BUCK1 power-good interrupt INT_BUCK_0_1.BUCK1_PG_INT:
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the BUCK_0_1_STAT.BUCK1_PG_STAT status bit.
5
4
Reserved
R
0
BUCK1_ILIM
_MASK
R/W
0 *
Masking for BUCK1 current limit detection interrupt INT_BUCK_0_1.BUCK1_ILIM_INT:
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the BUCK_0_1_STAT.BUCK1_ILIM_STAT status bit.
3
2
Reserved
R/W
R/W
0
BUCK0_PG_MASK
1 *
Masking for BUCK0 power-good interrupt INT_BUCK_0_1.BUCK0_PG_INT:
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the BUCK_0_1_STAT.BUCK1_PG_STAT status bit.
1
0
Reserved
R
0
BUCK0_ILIM
_MASK
R/W
0 *
Masking for BUCK0 current limit detection interrupt INT_BUCK_0_1.BUCK0_ILIM_INT:
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the BUCK_0_1_STAT.BUCK1_ILIM_STAT status bit.
7.6.1.32 BUCK_2_3_MASK
Address: 0x20
D7
D6
D5
D4
D3
D2
D1
D0
Reserved
BUCK3_PG
_MASK
Reserved
BUCK3_ILIM
_MASK
Reserved
BUCK2_PG
_MASK
Reserved
BUCK2_ILIM
_MASK
Bits
Field
Type
R/W
R/W
Default
Description
7
6
Reserved
0
BUCK3_PG_MASK
1 *
Masking for BUCK3 power-good interrupt INT_BUCK_2_3.BUCK3_PG_INT:
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the BUCK_2_3_STAT.BUCK3_PG_STAT status bit.
5
4
Reserved
R
0
BUCK3_ILIM
_MASK
R/W
0 *
Masking for BUCK3 current limit detection interrupt INT_BUCK_2_3.BUCK3_ILIM_INT:
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the BUCK_2_3_STAT.BUCK3_ILIM_STAT status bit.
3
2
Reserved
R/W
R/W
0
BUCK2_PG_MASK
1 *
Masking for BUCK2 power-good interrupt INT_BUCK_2_3.BUCK2_PG_INT:
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the BUCK_2_3_STAT.BUCK1_PG_STAT status bit.
1
0
Reserved
R
0
BUCK2_ILIM
_MASK
R/W
0 *
Masking for BUCK2 current limit detection interrupt INT_BUCK_2_3.BUCK2_ILIM_INT:
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the BUCK_2_3_STAT.BUCK1_ILIM_STAT status bit.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
41
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
7.6.1.33 SEL_I_LOAD
Address: 0x21
D7
D6
D5
D4
D3
D2
D1
D0
Reserved
LOAD_CURRENT_BUCK
_SELECT[1:0]
Bits
Field
Type
R/W
R/W
Default
00 0000
0x0
Description
7:2
Reserved
1:0 LOAD_CURRENT_
BUCK_SELECT
[1:0]
Start the current measurement on the selected converter core:
0x0 - BUCK0
0x1 - BUCK1
0x2 - BUCK2
0x3 - BUCK3
The measurement is started when this register is written.
7.6.1.34 I_LOAD_2
Address: 0x22
D7
D6
D5
D4
D3
D2
D1
D0
Reserved
BUCK_LOAD_CURRENT[9:8]
Bits
7:2
Field
Type
R
Default
00 0000
0x0
Description
Reserved
1:0
BUCK_LOAD_
CURRENT[9:8]
R
This register describes 2 MSB bits of the average load current on the selected
converter core with a resolution of 20 mA per LSB and a maximum 20 A current.
7.6.1.35 I_LOAD_1
Address: 0x23
D7
D6
D5
D4
D3
D2
D1
D0
BUCK_LOAD_CURRENT[7:0]
Bits
Field
Type
Default
Description
7:0
BUCK_LOAD_
CURRENT[7:0]
R
0x0
This register describes 8 LSB bits of the average load current on selected converter
core with a resolution of 20 mA per LSB and maximum 20-A current.
42
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LP8758-E3 is designed for applications powered from a 2.5-V to 5.5-V input supply that require multiple
power rails. The device provides four step-down converters. All the step-down converters support dynamic
voltage scaling through I2C interface to provide optimum power savings. The power sequencing of the four output
voltage rails is programmable.
8.2 Typical Application
L0
VIN
SW_B0
Load
Load
VIN_B0
VIN_B1
VIN_B2
VIN_B3
CIN5
CIN4
470 nH
COUT0
22 µF
CPOL0
22 µF
CIN0
CIN1
CIN2
CIN3
10 µF
10 µF
10 µF
10 µF
22 µF
22 µF
FB_B0
L1
SW_B1
470 nH
COUT1
22 µF
CPOL1
22 µF
FB_B1
L2
SW_B2
Load
Load
470 nH
COUT2
22 µF
CPOL2
22 µF
VIO
VANA
AGND
CVANA
100 nF
FB_B2
SDA
SCL
nINT
NRST
EN1
EN2
L3
SW_B3
470 nH
COUT3
22 µF
CPOL3
22 µF
Host
Processor
FB_B3
Figure 19. LP8758-E3 Typical Application Circuit
Table 6. Design Parameters
8.2.1 Design Requirements
DESIGN PARAMETER
EXAMPLE VALUE
Input voltage
Output voltages
3.3 V
1000 mV, 1200 mV, 1800 mV, and 2500 mV
Auto mode (PWM-PFM)
Converter operation mode
Maximum load currents
Inductor current limits
1.5 A, 2.25 A, 3 A, and 3 A
2.5 A, 3.5 A, 4.5 A, and 4.5 A
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
43
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
8.2.2 Detailed Design Procedure
The performance of the LP8758-E3 device depends greatly on the care taken in designing the printed circuit
board (PCB). The use of low-inductance and low serial-resistance ceramic capacitors is strongly recommended,
while proper grounding is crucial. Attention must be given to decoupling the power supplies. Decoupling
capacitors must be connected close to the device and between the power and ground pins to support high peak
currents being drawn from system power rail during turnon of the switching MOSFETs. Keep input and output
traces as short as possible, because trace inductance, resistance, and capacitance can easily become the
performance limiting items. The separate power pins VIN_Bx are not connected together internally. The VIN_Bx
power connections must be connected together outside the package using power plane construction.
8.2.2.1 Application Components
8.2.2.1.1 Inductor Selection
DC bias current characteristics of inductors must be considered. Different manufacturers follow different
saturation current rating specifications, so attention must be given to details. DC bias curves should be requested
from manufacturers as part of the inductor selection process. Minimum effective value of inductance to ensure
good performance is 0.33 μH at maximum load current over the operating temperature range of the inductor. The
DC resistance of the inductor must be less than 0.05 Ω for good efficiency at high-current condition. The inductor
AC loss (resistance) also affects conversion efficiency. Higher Q factor at switching frequency usually gives
better efficiency at light load to middle load. See Table 7. Shielded inductors are preferred as they radiate less
noise.
Table 7. Recommended Inductors
MANUFACTURER
MURATA
TDK
PART NUMBER
DFE201610E-R47M=P2
VLS252010HBX-R47M
TFM2016GHM-0R47M
DFE322512C R47
VALUE (µH)
0.47
DIMENSIONS L × W × H (mm)
2 × 1.6 × 1
DCR (mΩ)
26 (typical), 32 (maximum)
29 (typical), 35 (maximum)
46 (maximum)
0.47
2.5 × 2 × 1
TDK
0.47
2 × 1.6 × 1
TOKO
0.47
3.2 × 2.5 × 1.2
21 (typical), 31 (maximum)
8.2.2.1.2 Input Capacitor Selection
A ceramic input capacitor of 10 μF, 6.3 V is sufficient for most applications. Place the power input capacitor as
close as possible to the VIN_Bx pin and PGND_Bx pin of the device. A larger value or higher voltage rating may
be used to improve input voltage filtering. Use X7R or X5R types; do not use Y5V or F. DC bias characteristics of
ceramic capacitors must be considered when selecting case sizes like 0402. Minimum effective input
capacitance to ensure good performance is 1.9 μF per buck input at maximum input voltage DC bias including
tolerances and over ambient temp range, assuming that there are at least 22 μF of additional capacitance
common for all the power input pins on the system power rail. See Table 8.
The input filter capacitor supplies current to the high-side FET switch in the first half of each cycle and reduces
voltage ripple imposed on the input power source. A ceramic capacitor's low equivalent series resistance (ESR)
provides the best noise filtering of the input voltage spikes due to this rapidly changing current. Select an input
filter capacitor with sufficient ripple current rating.
The VANA input is used to supply analog and digital circuits in the device. See recommended components from
Table 9 for VANA input supply filtering.
Table 8. Recommended Power Input Capacitors (X5R Dielectric)
MANUFACTURER
PART NUMBER
VALUE
CASE SIZE
DIMENSIONS L × W × H (mm) VOLTAGE RATING (V)
Murata
GRM188R60J106ME47 10 µF (20%)
0603
1.6 × 0.8 × 0.8
6.3
Table 9. Recommended VANA Supply Filtering Components
MANUFACTURER
PART NUMBER
VALUE
CASE SIZE
DIMENSIONS L × W × H (mm)
VOLTAGE RATING
(V)
Samsung
Murata
CL03A104KP3NNNC 100 nF (10%)
0201
0201
0.6 × 0.3 × 0.3
0.6 × 0.3 × 0.3
10
GRM033R61A104KE8 100 nF (10%)
4
6.3
44
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
8.2.2.1.3 Output Capacitor Selection
Use ceramic capacitors, X7R or X5R types; do not use Y5V or F. DC bias voltage characteristics of ceramic
capacitors must be considered. DC bias characteristics vary from manufacturer to manufacturer, and DC bias
curves should be requested from them as part of the capacitor selection process. The output filter capacitor
smooths out current flow from the inductor to the load, helps maintain a steady output voltage during transient
load changes and reduces output voltage ripple. These capacitors must be selected with sufficient capacitance
and sufficiently low ESR and ESL to perform these functions. The minimum effective output capacitance to
ensure good performance is 10 μF per output voltage rail at the output voltage DC bias, including tolerances and
over ambient temperature range.
The output voltage ripple is caused by the charging and discharging of the output capacitor and also due to its
RESR. The RESR is frequency dependent (as well as temperature dependent); make sure the value used for
selection process is at the switching frequency of the part. See Table 10.
A higher output capacitance improves the load step behavior and reduces the output voltage ripple as well as
decreases the PFM switching frequency. For most applications one 22-μF 0603 capacitor for COUT per voltage
rail is suitable. A point-of-load (POL) capacitance CPOL can be added as shown in Figure 19. Although the loop
compensation of the converter can be programmed to adapt to virtually several hundreds of microfarads COUT, it
is preferable for COUT to be < 50 µF . Choosing higher than that is not necessarily of any benefit. Note: the output
capacitor may be the limiting factor in the output voltage ramp, especially for very large (> 100 µF) output
capacitors. For large output capacitors, the output voltage might be slower than the programmed ramp rate at
voltage transitions, because of the higher energy stored on the output capacitance. Also at start-up, the time
required to charge the output capacitor to target value might be longer. At shutdown, if the output capacitor is
discharged by the internal discharge resistor, more time is required to settle VOUT down as a consequence of the
increased time constant.
Table 10. Recommended Output Capacitors (X5R Dielectric)
MANUFACTURER
PART NUMBER
VALUE
CASE SIZE
DIMENSIONS L × W × H
(mm)
VOLTAGE RATING (V)
Samsung
Murata
CL10A226MP8NUNE
22 µF (20%)
22 µF (20%)
0603
0603
1.6 × 0.8 × 0.8
1.6 × 0.8 × 0.8
10
GRM188R60J226MEA0
6.3
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
45
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
8.2.3 Application Curves
Measurements are done using typical application set up with connections shown in Figure 19. Graphs may not
reflect the OTP default settings. Unless otherwise specified: VIN = 3.7 V, V(NRST) = 1.8 V, TA = 25 °C, ƒSW = 3
MHz, L = 470 nH (TDK VLS252010HBX-R47M), ILIM FWD set to maximum 5 A.
100
95
90
85
80
100
90
80
70
60
50
40
30
20
10
0
1000 mV
1200 mV
1800 mV
2500 mV
PFM Operation
1000 mV
1200 mV
1800 mV
2500 mV
PWM Operation
1
10
100
Load Current (mA)
1000
5000
2500
3000
3500
4000
Input Voltage (mV)
4500
5000
5500
D014
D002
VIN = 3.7 V
Load = 100 mA
VOUT settings = 1000 mV, 1200 mV, 1800 mV, and 2500 mV
VOUT settings = 1000 mV, 1200 mV, 1800 mV, and 2500 mV
Figure 20. Efficiency vs Load Current
Figure 21. Efficiency vs Input Voltage in PFM Mode
100
100
1000 mV
1200 mV
1800 mV
1000 mV
1200 mV
1800 mV
2500 mV
95
90
85
80
75
70
2500 mV
95
90
85
80
2500
3000
3500
4000
Input Voltage (mV)
4500
5000
5500
2500
3000
3500
4000
Input Voltage (mV)
4500
5000
5500
D041
D016
Load = 1A
Load = 3A
VOUT settings = 1000 mV, 1200 mV, 1800 mV, and 2500 mV
VOUT settings = 1000 mV, 1200 mV, 1800 mV, and 2500 mV
Figure 22. Efficiency vs Input Voltage in PWM Mode
Figure 23. Efficiency vs Input Voltage in PWM Mode
46
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
0
1015
1010
1005
1000
995
1000 mV
1200 mV
1800 mV
2500 mV
-0.025
-0.05
-0.075
-0.1
PFM Operation
-0.125
-0.15
-0.175
-0.2
PWM Operation
-0.225
-0.25
0
500 1000 1500 2000 2500 3000 3500 4000
Output Current (mA)
1
10
100
Output Current (mA)
1000
5000
D005
D047
Change in Output Voltage from Zero Load (%)
VOUT setting = 1000 mV
VOUT settings = 1000 mV, 1200 mV, 1800 mV, and 2500 mV
Figure 24. DC Load Regulation in PWM mode
Figure 25. Output Voltage vs Load Current in
PWM-PFM Mode
2515
0.06
0.04
0.02
0
1000mV
1200mV
1800mV
2500mV
PFM Operation
2510
2505
2500
-0.02
-0.04
-0.06
PWM Operation
2495
2490
1
10
100
Output Current (mA)
1000
5000
2500
3000
3500
4000
Input Voltage (mV)
4500
5000
5500
D046
D044
VOUT setting = 2500 mV
Change in Output Voltage from VIN = 3.7 V (%)
Load = 1 A
VOUT settings = 1000 mV, 1200 mV, 1800 mV, and 2500 mV
Figure 26. Output Voltage vs Load Current in
PWM-PFM Mode
Figure 27. DC Line Regulation in PWM Mode
1010
1005
1000
995
V(SW_Bx) (5 V/div)
V(EN1) (1 V/div)
PWM Mode
PFM Mode
VOUT (200 mV/div)
-50
-25
0
25
50
75
100
125
Time (40 ms/div)
Temperature (èC)
D048
Load = 0 A
VOUT setting = 1000 mV
Load = 1 A (PWM Mode) and 100 mA (PFM Mode)
Figure 29. Start-up with EN1
Figure 28. Output Voltage vs Temperature
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
47
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
V(SW_Bx) (5 V/div)
V(SW_Bx) (5 V/div)
V(EN1) (1 V/div)
V(EN1) (1 V/div)
ILOAD (500 mA/div)
ILOAD (500 mA/div)
VOUT (200 mV/div)
VOUT (50 mV/div)
Time (40 ms/div)
Time (200 ms/div)
Load = 1 A
Figure 30. Start-up with EN1
Figure 31. Start-up With Short on Output
VOUT0 (1 V/div)
VOUT1 (1 V/div)
V(SW_Bx) (5 V/div)
VOUT (200 mV/div)
VOUT2 (1 V/div)
VOUT3 (1 V/div)
V(EN1) (1 V/div)
Time (10 ms/div)
Time (4 ms/div)
Load = 0 A
Load = 0 A
Enable and disable delays = default
VOUT settings = default
Figure 33. Shutdown with EN1
Figure 32. VOUT0,1,2,3: Start-up and Shutdown with Default
Register Settings, triggered by EN1.
VOUT (10 mV/div)
VOUT (10 mV/div)
V(SW_B0) (2 V/div)
V(SW_B0) (2 V/div)
Time (200 ns/div)
Time (40 ms/div)
Load = 200 mA
Load = 10 mA
Figure 35. Output Voltage Ripple, Forced PWM Mode
Figure 34. Output Voltage Ripple, PFM Mode
48
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
V(SW_Bx) (2 V/div)
V(SW_Bx) (2 V/div)
VOUT (10 mV/div)
VOUT (10 mV/div)
Time (4 ms/div)
Time (4 ms/div)
Figure 36. Transient from PFM-to-PWM Mode
Figure 37. Transient from PWM-to-PFM Mode
VIN (500 mV/div)
VOUT (20 mV/div)
ILOAD (1 A/div)
VOUT (10 mV/div)
Time (40 ms/div)
Time (40 ms/div)
Load = 4 A
VOUT = 1000 mV
Load = 0 A → 2 A → 0 A
TR = TF = 400 ns
VOUT = 1 V
VIN stepping 3.3 V ↔ 3.8 V, TR = TF = 10 µs
Figure 38. Transient Line Response
Figure 39. Transient Load Step Response, AUTO Mode
VOUT (50 mV/div)
VOUT (20 mV/div)
ILOAD (1 A/div)
ILOAD (1 A/div)
Time (40 ms/div)
Time (40 ms/div)
Load = 1A → 4 A → 1A
TR = TF = 1 µs
VOUT = 1 V
Load = 0 A → 2 A → 0 A
TR = TF = 400 ns
VOUT = 1 V
Figure 41. Transient Load Step Response,
Forced PWM Mode
Figure 40. Transient Load Step Response,
Forced PWM Mode
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
49
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
VOUT (200 mV/div)
VOUT (200 mV/div)
Time (400 µs/div)
Time (400 µs/div)
Figure 42. VOUT Transition From 0.6 V to 1.4 V With
Different Slew Rate Settings
Figure 43. VOUT Transition From 1.4 V to 0.6 V With
Different Slew Rate Settings
9 Power Supply Recommendations
The device is designed to operate from an input voltage supply range between 2.5 V and 5.5 V. This input supply
must be well-regulated and able to withstand maximum input current and maintain stable voltage without voltage
drop even at load transition condition. The resistance of the input supply rail must be low enough that the input
current transient does not cause too high drop in the LP8758-E3 supply voltage that can cause false UVLO fault
triggering. If the input supply is located more than a few inches from the LP8758-E3 additional bulk capacitance
may be required in addition to the ceramic bypass capacitors.
50
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
10 Layout
10.1 Layout Guidelines
The high frequency and large switching currents of the LP8758-E3 make the choice of layout important. Good
power supply results only occur when care is given to proper design and layout. Layout affects noise pickup and
generation and can cause a good design to perform with less-than-expected results. With a range of output
currents from milliamps to 4 A per converter core, good power supply layout is much more difficult than most
general PCB design. The following steps should be used as a reference to ensure the device is stable and
maintains proper voltage and current regulation across its intended operating voltage and current range.
1. Place CIN as close as possible to the VIN_Bx pin and the PGND_Bxx pin. Route the VIN trace wide and thick
to avoid IR drops. The trace between the positive node of the input capacitor and the LP8758-E3 VIN_Bx
pin(s), as well as the trace between the input capacitor's negative node and power PGND_Bxx pin(s), must
be kept as short as possible. The input capacitance provides a low-impedance voltage source for the
switching converter. The inductance of the connection is the most important parameter of a local decoupling
capacitor — parasitic inductance on these traces must be kept as tiny as possible for proper device
operation.
2. The output filter, consisting of Lx and COUTx, converts the switching signal at SW_Bx to the noiseless output
voltage. It must be placed as close as possible to the device keeping the switch node small, for best EMI
behavior. Route the traces between the output capacitors of the device and the load (or input capacitors of
the load) direct and wide to avoid losses due to the IR drop.
3. Input for analog blocks (VANA and AGND) must be isolated from noisy signals. Connect VANA directly to a
quiet system voltage node and AGND to a quiet ground point where no IR drop occurs. Place the decoupling
capacitor as close to the VANA pin as possible. VANA must be connected to the same power node as
VIN_Bx pins.
4. If the load supports remote voltage sensing, connect the feedback pins FB_Bx of the device to the respective
sense pins on the load. The sense lines are susceptible to noise. They must be kept away from noisy signals
such as PGND_Bxx, VIN_Bx, and SW_Bx, as well as high bandwidth signals such as the I2C. Avoid both
capacitive as well as inductive coupling by keeping the sense lines short and direct. Run the lines in a quiet
layer. Isolate them from noisy signals by a voltage or ground plane if possible.
5. PGND_Bxx, VIN_Bx and SW_Bx must be routed on thick layers. They must not surround inner signal layers
which are not able to withstand interference from noisy PGND_Bxx, VIN_Bx and SW_Bx.
Due to the small package of this converter and the overall small solution size, the thermal performance of the
PCB layout is important. Many system-dependent issues such as thermal coupling, airflow, added heat sinks and
convection surfaces, and the presence of other heat-generating components affect the power dissipation limits of
a given component. Proper PCB layout, focusing on thermal performance, results in lower die temperatures.
Wide power traces come with the ability to sink dissipated heat. This can be improved further on multi-layer PCB
designs with vias to different planes. This results in reduced junction-to-ambient (RθJA) and junction-to-board
(RθJB) thermal resistances and thereby reduces the device junction temperature, TJ. Performing a careful system-
level 2D or full 3D dynamic thermal analysis at the beginning product design process is strongly recommended,
using a thermal modeling analysis software.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
51
Product Folder Links: LP8758-E3
LP8758-E3
SNVSBP2 –FEBRUARY 2020
www.ti.com
10.2 Layout Example
Via to GND plane
Via to VIN plane
VOUT2
VOUT3
L2
COUT2
COUT3
L3
VIN
GND
CIN2
CIN3
VIN
_B2
SW
_B2
PGND
_B23
SW
_B3
VIN
_B3
CIN5
VIN
VIN
VIN
_B2
SW
_B2
PGND
_B23
SW
_B3
VIN
_B3
FB
_B2
PGND
_B23
FB
_B3
VIN
GND
SCL
SDA
EN1
VANA
AGND
SGND
GND
NRST
EN2
nINT
FB
_B0
PGND
_B01
FB
_B1
VIN
_B0
SW
_B0
PGND
_B01
SW
_B1
VIN
_B1
CVANA
VIN
_B0
SW
_B0
PGND
_B01
SW
_B1
VIN
_B1
VIN
CIN0
VIN
Pin A1
CIN4
CIN1
GND
VIN
L0
COUT0
COUT1
L1
VOUT0
VOUT1
Figure 44. LP8758-E3 Board Layout
52
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: LP8758-E3
LP8758-E3
www.ti.com
SNVSBP2 –FEBRUARY 2020
11 Device and Documentation Support
11.1 Device Support
11.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
11.2 Documentation Support
11.2.1 Related Documentation
For related documentation, see the following:
•
•
Texas Instruments, DSBGA Wafer Level Chip Scale Package application report
Texas instruments, Using the LP8758EVM Evaluation Module user's guide
11.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.4 Community Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
11.5 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
53
Product Folder Links: LP8758-E3
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
LP8758A2E3YFFR
ACTIVE
DSBGA
YFF
35
3000 RoHS & Green
SAC396
Level-1-260C-UNLIM
-40 to 85
LP8758A2E3
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
D: Max = 2.91 mm, Min = 2.85 mm
E: Max = 2.16 mm, Min = 2.1 mm
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明