LP87332DRHDRQ1 [TI]
用于 J6 入门处理器的汽车类双路 3A 降压转换器和双路线性稳压器 | RHD | 28 | -40 to 125;型号: | LP87332DRHDRQ1 |
厂家: | TEXAS INSTRUMENTS |
描述: | 用于 J6 入门处理器的汽车类双路 3A 降压转换器和双路线性稳压器 | RHD | 28 | -40 to 125 开关 转换器 稳压器 |
文件: | 总79页 (文件大小:3109K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
LP87332D-Q1 双路高电流降压转换器和双路线性稳压器
1 特性
2 应用
•
具有符合 AEC-Q100 标准的下列特性:
•
•
•
•
•
汽车音响主机和仪表组
汽车摄像头模块
环视系统 ECU
雷达系统 ECU
汽车显示屏
– 器件温度等级 1:–40°C 至 +125°C 环境工作温
度范围
•
•
输入电压:2.8V 至 5.5V
两个高效降压直流/直流转换器:
– 输出电压:0.7V 至 3.36V
– 最大输出电流为 3A
3 说明
LP87332D-Q1 旨在满足汽车摄像头和雷达应用中新型
处理器和平台的电源管理要求。该器件具有两个降压直
流/直流转换器、两个线性稳压器以及两个通用数字输
出信号。该器件由 I2C 兼容串行接口和使能信号进行控
制。
– 可编程输出电压压摆率范围:0.5mV/µs 至
10mV/µs
– 2MHz 开关频率
– 用于降低 EMI 的扩频模式和相位交错
两个线性稳压器:
•
– 输入电压:2.5V 至 5.5V
– 输出电压:0.8V 至 3.3V
– 最大输出电流为 300mA
可配置通用输出信号(GPO、GPO2)
具有可编程屏蔽的中断功能
可编程电源正常信号 (PGOOD)
输出短路和过载保护
自动 PWM/PFM(AUTO 模式)运行,可在较宽输出
电流范围内提供高效率。LP87332D-Q1 支持远程电压
感应,可补偿稳压器输出与负载点 (POL) 之间的 IR 压
降,从而提高输出电压的精度。此外,可以强制开关时
钟进入 PWM 模式以及将其与外部时钟同步,从而更大
限度地降低干扰。
•
•
•
•
•
•
•
LP87332D-Q1 器件还支持可编程启动、关断延迟与时
序控制(包括与使能信号同步的 GPO 信号)。在启动
和电压变化期间,器件会对输出转换率进行控制,从而
更大限度地减小输出电压过冲和浪涌电流。
过热警告和保护
过压保护 (OVP) 和欠压锁定 (UVLO)
具有可湿性侧面的 28 引脚、5mm × 5mm VQFN 封
装
器件信息(1)
VIN
VOUT_B0
器件型号
封装
封装尺寸(标称值)
VIN_B0
VIN_B1
SW_B0
FB_B0
LOAD
LP87332D-Q1
VQFN (28)
5.00mm × 5.00mm
VIN_LDO0
VIN_LDO1
(1) 如需了解所有可用封装,请参阅数据表末尾的可订购产品附
录。
VANA
VOUT_B1
100
90
SW_B1
FB_B1
LOAD
SDA
SCL
nINT
EN
VOUT_LDO0
VOUT_LDO1
VOUT_LDO0
VOUT_LDO1
80
CLKIN (GPO2)
GPO
70
PGOOD
GNDs
60
Vin=3.7V, Vout=1.0V
Vin=3.7V, Vout=1.8V
Vin=3.7V, Vout=2.5V
50
0.001
Copyright © 2017, Texas Instruments Incorporated
0.01
0.1
Output Current (A)
1
3
D001
简化版原理图
直流/直流效率与输出电流间的关系
本文档旨在为方便起见,提供有关 TI 产品中文版本的信息,以确认产品的概要。有关适用的官方英文版本的最新信息,请访问
www.ti.com,其内容始终优先。TI 不保证翻译的准确性和有效性。在实际设计之前,请务必参考最新版本的英文版本。
English Data Sheet: SNVSAT1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
Table of Contents
1 特性................................................................................... 1
2 应用................................................................................... 1
3 说明................................................................................... 1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
6 Specifications.................................................................. 5
6.1 Absolute Maximum Ratings........................................ 5
6.2 ESD Ratings............................................................... 5
6.3 Recommended Operating Conditions.........................5
6.4 Thermal Information....................................................6
6.5 Electrical Characteristics.............................................6
6.6 I2C Serial Bus Timing Parameters............................ 11
6.7 Typical Characteristics..............................................14
7 Detailed Description......................................................15
7.1 Overview...................................................................15
7.2 Functional Block Diagram.........................................16
7.3 Feature Description...................................................16
7.4 Device Functional Modes..........................................34
7.5 Programming............................................................ 35
7.6 Register Maps...........................................................38
8 Application and Implementation..................................59
8.1 Application Information............................................. 59
8.2 Typical Application.................................................... 59
9 Power Supply Recommendations................................66
10 Layout...........................................................................67
10.1 Layout Guidelines................................................... 67
10.2 Layout Example...................................................... 68
11 Device and Documentation Support..........................69
11.1 Device Support........................................................69
11.2 Receiving Notification of Documentation Updates..69
11.3 支持资源..................................................................69
11.4 Trademarks............................................................. 69
11.5 Electrostatic Discharge Caution..............................69
11.6 Glossary..................................................................69
12 Mechanical, Packaging, and Orderable
Information.................................................................... 69
4 Revision History
注:以前版本的页码可能与当前版本的页码不同
Changes from Revision * (September 2017) to Revision A (June 2021)
Page
更新了整个文档中的表、图和交叉参考的编号格式.............................................................................................1
Updated the LDO Output Capacitor Selection section..................................................................................... 61
•
•
Copyright © 2021 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
5 Pin Configuration and Functions
21
20
19
18
17
16
15
SW_B0
SW_B1
SW_B1
VIN_B1
VIN_B1
CLKIN
22
14
13
12
11
10
9
SW_B0
23
VIN_B0
24
VIN_B0
25
THERMAL PAD
GPO
26
PGOOD
nINT
27
VIN_LDO0
VIN_LDO1
28
8
1
2
3
4
5
6
7
图 5-1. RHD Package 28-Pin VQFN With Thermal Pad Top View
表 5-1. Pin Functions
PIN
TYPE(1)
DESCRIPTION
NUMBER
NAME
1
2
3
4
5
VOUT_LDO0
FB_B0
P/O
A
LDO0 output. If the LDO0 is not used, leave the pin floating.
Output voltage feedback (positive) for Buck 0.
Output voltage feedback (positive) for Buck 1
FB_B1
A
AGND
G
Ground.
VANA
P/I
Supply voltage for analog and digital blocks. Must be connected to same node with VIN_Bx.
Programmable enable signal for regulators and GPOs. If the pin is not used, leave the pin
floating.
6
EN
D/I
7
8
9
VOUT_LDO1
VIN_LDO1
nINT
P/O
P/I
LDO1 output. If LDO1 is not used, leave the pin floating.
Power input for LDO1. If LDO1 is not used, connect the pin to VANA.
Open-drain interrupt output. Active LOW. If the pin is not used, connect the pin to ground.
D/O
External clock input. Alternative function is general-purpose digital output (GPO2). If the pin is
not used, leave the pin floating.
10
CLKIN
D/I/O
P/I
Input for Buck 1. The separate power pins VIN_Bx are not connected together internally -
VIN_Bx pins must be connected together in the application and be locally bypassed.
11, 12
VIN_B1
13, 14
15, 16
SW_B1
P/O
P/G
Buck 1 switch node. If the Buck 1 is not used, leave the pin floating.
PGND_B1
Power ground for Buck 1.
Serial interface clock input for I2C access. Connect a pullup resistor. If the I2C interface is not
used, connect the pin to Ground.
17
18
SCL
SDA
D/I
Serial interface data input and output for I2C access. Connect a pullup resistor. If the I2C
interface is not used, connect the pin to Ground.
D/I/O
19
SGND
PGND_B0
SW_B0
G
Ground.
20, 21
22, 23
P/G
P/O
Power ground for Buck 0.
Buck 0 switch node. If the Buck 0 is not used, leave the pin floating.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
表 5-1. Pin Functions (continued)
PIN
TYPE(1)
DESCRIPTION
NUMBER
NAME
Input for Buck 0. The separate power pins VIN_Bx are not connected together internally -
VIN_Bx pins must be connected together in the application and be locally bypassed.
24, 25
VIN_B0
P/I
26
27
28
GPO
D/O
D/O
P/I
General-purpose digital output. If the pin is not used, leave the pin floating.
Power-good indication signal. If the pin is not used, leave the pin floating.
Power input for LDO0. If the LDO0 is not used, connect the pin to VANA.
PGOOD
VIN_LDO0
—
Thermal
Pad
—
Connect to PCB ground plane using multiple vias for good thermal performance.
(1) A: Analog Pin, D: Digital Pin, G: Ground Pin, P: Power Pin, I: Input Pin, and O: Output Pin.
Copyright © 2021 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
6 Specifications
6.1 Absolute Maximum Ratings
Over operating free-air temperature range (unless otherwise noted)(1) (2)
MIN
–0.3
–0.3
–0.3
MAX UNIT
Voltage on power connections (must use the same
VIN_Bx, VANA
input supply)
6
6
V
V
V
VIN_LDOx
SW_Bx
Voltage on power connections
Voltage on buck switch nodes
(VIN_Bx + 0.3 V) with 6-V
maximum
(VANA + 0.3 V) with 6-V
maximum
FB_Bx
Voltage on buck voltage sense nodes
–0.3
V
(VIN_LDOx + 0.3 V) with 6-V
maximum
VOUT_LDOx
Voltage on LDO output
-0.3
–0.3
–0.3
V
V
V
SDA, SCL, nINT, EN
Voltage on logic pins (input or output pins)
Voltage on logic pins (input or output pins)
6
PGOOD, GPO, CLKIN
(GPO2)
(VANA + 0.3 V) with 6-V
maximum
TJ-MAX
Tstg
Junction temperature
Storage temperature
−40
–65
150
150
260
°C
Maximum lead temperature (soldering, 10 seconds)
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under 节 6.3.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to network ground.
6.2 ESD Ratings
VALUE
±2000
±500
UNIT
Human-body model (HBM), per AEC Q100-002(1)
All pins
V(ESD)
Electrostatic discharge
V
Charged-device model (CDM), per AEC
Q100-011
Corner pins (1, 7, 8, 14,
15, 21, 22, 28)
±750
(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
6.3 Recommended Operating Conditions
Over operating free-air temperature range (unless otherwise noted)
MIN
MAX
UNIT
INPUT VOLTAGE
Voltage on power connections (must use the same input
supply)
VIN_Bx, VANA
2.8
5.5
V
VIN_LDOx
EN, nINT
Voltage on LDO inputs
2.5
0
5.5
5.5
V
V
Voltage on logic pins (input or output pins)
Voltage on logic pins (input pin)
0
VANA with 5.5-V
maximum
CLKIN
V
V
V
PGOOD, GPO, GPO2
Voltage on logic pins (output pins)
0
0
VANA
1.95
Voltage on I2C interface, Standard (100 kHz), Fast (400
kHz), Fast+ (1 MHz), and High-Speed (3.4 MHz) Modes
SCL, SDA
Voltage on I2C interface, Standard (100 kHz), Fast (400
kHz), and Fast+ (1 MHz) Modes
VANA with 3.6-V
maximum
0
V
TEMPERATURE
TJ
Junction temperature
Ambient temperature
−40
−40
140
125
°C
°C
TA
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
6.4 Thermal Information
LP87332D-Q1
THERMAL METRIC(1)
RHD (VQFN)
28 PINS
36.7
UNIT
RθJA
Junction-to-ambient thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJCtop
RθJB
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
26.6
8.9
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
0.4
ψJB
8.8
RθJCbot
2.2
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
note.
6.5 Electrical Characteristics
Limits apply over the junction temperature range –40°C ≤ TJ ≤ +140°C, specified VVANA, VVIN_Bx, VVIN_LDOx, VVOUT_Bx
,
VVOUT_LDOx and IOUT range, unless otherwise noted. Typical values are at TJ = 25°C, VVANA = VVIN_Bx = VVIN_LDOx = 3.7 V,
and VOUT = 1 V, unless otherwise noted(1) (2)
.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
EXTERNAL COMPONENTS
Input filtering
capacitance for buck
regulators
Effective capacitance, connected from VIN_Bx
to PGND_Bx
CIN_BUCK
1.9
10
10
22
22
µF
Output filtering
capacitance for buck
regulators
COUT_BUCK
Effective capacitance
500
500
µF
Point-of-load (POL)
capacitance for buck
regulators
CPOL_BUCK
Optional POL capacitance
Total output capacitance
µF
µF
µF
COUT-
Buck output capacitance,
total (local and POL)
TOTAL_BUCK
Input filtering
capacitance for LDO
regulators
Effective capacitance, connected from
VIN_LDOx to AGND. CIN_LDO must be at least
two times larger than COUT_LDO
CIN_LDO
0.6
0.4
2.2
1
Output filtering
capacitance for LDO
regulators
COUT_LDO
Effective capacitance
2.7
10
µF
Input and output
capacitor ESR
ESRC
[1-10] MHz
2
mΩ
0.47
L
Inductor
Inductance of the inductor
µH
–30%
30%
DCRL
Inductor DCR
25
mΩ
BUCK REGULATORS
V(VIN_Bx)
V(VANA)
,
VIN_Bx and VANA pins must be connected to
the same supply line
Input voltage range
2.8
0.7
3.7
5.5
V
V
Programmable voltage range
Step size, 0.7 V ≤ VOUT < 0.73 V
Step size, 0.73 V ≤ VOUT < 1.4 V
Step size, 1.4 V ≤ VOUT ≤ 3.36 V
Output current
1
10
5
3.36
VOUT_Bx
Output voltage
Output current
mV
20
IOUT_Bx
3(3)
A
V
Input and Output voltage Minimum voltage between V(VIN_Bx) and
0.8
difference
VOUT to fulfill the electrical characteristics
Copyright © 2021 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
6.5 Electrical Characteristics (continued)
Limits apply over the junction temperature range –40°C ≤ TJ ≤ +140°C, specified VVANA, VVIN_Bx, VVIN_LDOx, VVOUT_Bx
,
VVOUT_LDOx and IOUT range, unless otherwise noted. Typical values are at TJ = 25°C, VVANA = VVIN_Bx = VVIN_LDOx = 3.7 V,
and VOUT = 1 V, unless otherwise noted(1) (2)
.
PARAMETER
TEST CONDITIONS
MIN
–20
TYP
MAX UNIT
Force PWM mode, VOUT < 1 V
Force PWM mode, VOUT ≥ 1 V
20
mV
DC output voltage
accuracy, includes
voltage reference, DC
load and line regulations,
process and temperature
–2%
2%
PFM mode, VOUT < 1 V, the average output
voltage level is increased by max. 20 mV
VOUT_Bx_DC
–20
40
mV
PFM mode, VOUT ≥ 1 V, the average output
voltage level is increased by max. 20 mV
2% + 20
mV
–2%
PWM mode
10
25
Ripple voltage
mVp-p
%/V
PFM mode, IOUT = 10 mA
IOUT = 1 A
DCLNR
DCLDR
DC line regulation
±0.05
DC load regulation in
PWM mode
VOUT_Bx = 1 V, IOUT from 0 to IOUT(max)
0.3%
±55
Transient load step
response
IOUT = 0.1 A to 2 A, TR = TF = 400 ns, PWM
mode
mV
TLDSR
TLNSR
V(VIN_Bx) stepping 3 V ↔ 3.5 V, TR = TF = 10
µs, IOUT = IOUT(max)
Transient line response
±10
mV
A
Programmable range
1.5
4
Forward current limit per
phase (peak for every
switching cycle)
Step size
0.5
7.5%
7.5%
ILIM FWD
Accuracy, V(VIN_Bx) ≥ 3 V, ILIM = 4 A
Accuracy, 2.8 V ≤ V(VIN_Bx) < 3 V, ILIM = 4 A
–5%
20%
20%
–20%
Negative current limit per
phase
ILIM NEG
1.6
2.0
50
3.0
A
On-resistance, high-side Each phase, between VIN_Bx and SW_Bx
FET pins (I = 1 A)
RDS(ON) HS FET
110
mΩ
On-resistance, low-side Each phase, between SW_Bx and PGND_Bx
RDS(ON) LS FET
ƒSW
45
2
90
mΩ
MHz
µs
FET
pins (I = 1 A)
Switching frequency
PWM mode
1.8
2.2
From ENx to VOUT_Bx = 0.35 V (slew-rate
control begins)
Start-up time (soft start)
120
SLEW_RATEx[2:0] = 010, COUT-TOTAL_BUCK
80 µF
<
<
<
10
7.5
SLEW_RATEx[2:0] = 011, COUT-TOTAL_BUCK
130 µF
SLEW_RATEx[2:0] = 100, COUT-TOTAL_BUCK
250 µF
3.8
Output voltage slew-
rate(4)
–15%
15% mV/µs
SLEW_RATEx[2:0] = 101, COUT-TOTAL_BUCK
< 500 µF
1.9
SLEW_RATEx[2:0] = 110, COUT-TOTAL_BUCK
< 500 µF
0.94
0.47
550
290
250
SLEW_RATEx[2:0] = 111, COUT-TOTAL_BUCK
< 500 µF
PFM-to-PWM - current
threshold(5)
IPFM-PWM
IPWM-PFM
RDIS_Bx
mA
mA
PWM-to-PFM - current
threshold(5)
Output pulldown
resistance
Regulator disabled
150
350
Ω
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
6.5 Electrical Characteristics (continued)
Limits apply over the junction temperature range –40°C ≤ TJ ≤ +140°C, specified VVANA, VVIN_Bx, VVIN_LDOx, VVOUT_Bx
,
VVOUT_LDOx and IOUT range, unless otherwise noted. Typical values are at TJ = 25°C, VVANA = VVIN_Bx = VVIN_LDOx = 3.7 V,
and VOUT = 1 V, unless otherwise noted(1) (2)
.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
V(VIN_Bx) and V(VANA) fixed 3.7 V
Overvoltage threshold (compared to DC output
39
–53
4
50
64
mV
–29
Output voltage
voltage level, VVOUT_Bx_DC
Undervoltage threshold (compared to DC
output voltage level, VVOUT_Bx_DC
)
monitoring for PGOOD
pin and for power-good
Interrupt
–40
)
Deglitch time during operation and after
voltage change
15
µs
µs
Gating time for PGOOD
signal after regulator
PGOOD_MODE = 0
800
enable or voltage change
LDO REGULATORS
Input voltage range for
LDO power inputs
VIN_LDOx
VIN_LDOx can be higher or lower than V(VANA)
2.5
0.8
3.7
0.1
5.5
3.3
V
Programmable voltage range
Step size
VOUT_LDOx
IOUT_LDOx
Output voltage
Output current
V
300
200
20
mA
V(VIN_LDOx) – V(VOUT_LDOx), IOUT = IOUT(max)
Programmed output voltage is higher than
V(VIN_LDOx)
,
Dropout voltage
mV
mV
DC output voltage
VOUT < 1 V
–20
accuracy, includes
VOUT_LDO_DC
voltage reference, DC
load and line regulations,
process, temperature
VOUT ≥ 1 V
–2%
2%
DCLNR
DCLDR
DC line regulation
DC load regulation
IOUT = 1 mA
0.1
%/V
IOUT = 1 mA to IOUT(max)
0.8%
Transient load step
response
TLDSR
TLNSR
PSRR
IOUT = 1 mA to 300 mA, TR = TF = 1 µs
–50/+40
±7
mV
mV
dB
V(VIN_LDOx) stepping 3 V ↔ 3.5 V, TR = TF = 10
µs, IOUT = IOUT(max)
Transient line response
Power supply ripple
rejection
ƒ = 10 kHz, IOUT = IOUT(max)
53
Noise
10 Hz < F < 100 kHz, IOUT = IOUT(max)
VOUT = 0 V
82
500
300
15
µVrms
mA
ISHORT(LDOx)
LDO current limit
Start-up time
400
150
600
350
From enable to valid output voltage
µs
Slew rate during start-up
mV/µs
Output pulldown
resistance
RDIS_LDOx
Regulator disabled
250
Ω
Overvoltage monitoring, voltage rising
(compared to DC output voltage level,
106%
3%
108%
3.5%
92%
110%
4%
VOUT_LDO_DC
)
Overvoltage monitoring, hysteresis
Output voltage
monitoring for PGOOD
pin and for power-good
interrupt
Undervoltage monitoring, voltage falling
(compared to DC output voltage level,
90%
94%
VOUT_LDO_DC
)
Undervoltage monitoring, hysteresis
3%
4
3.5%
4%
15
Deglitch time during operation and after
voltage change
µs
Copyright © 2021 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
6.5 Electrical Characteristics (continued)
Limits apply over the junction temperature range –40°C ≤ TJ ≤ +140°C, specified VVANA, VVIN_Bx, VVIN_LDOx, VVOUT_Bx
,
VVOUT_LDOx and IOUT range, unless otherwise noted. Typical values are at TJ = 25°C, VVANA = VVIN_Bx = VVIN_LDOx = 3.7 V,
and VOUT = 1 V, unless otherwise noted(1) (2)
.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
Gating time for PGOOD
signal after regulator
PGOOD_MODE = 0
800
µs
enable or voltage change
EXTERNAL CLOCK AND PLL
Nominal frequency
1
24
MHz
fEXT_CLK
External input clock(6)
Nominal frequency step size
1
Required accuracy from nominal frequency
Delay for missing clock detection
Delay and debounce for clock detection
–30%
10%
1.8
µs
20
External clock detection
Clock change delay
(internal to external)
Delay from valid clock detection to use of
external clock
600
300
µs
PLL output clock jitter
Cycle to cycle
ps, p-p
PROTECTION FUNCTIONS
Temperature rising, TDIE_WARN_LEVEL = 0
115
127
125
137
20
135
Thermal warning
Temperature rising, TDIE_WARN_LEVEL = 1
Hysteresis
147
°C
°C
Temperature rising
Hysteresis
140
150
20
160
Thermal shutdown
VANA overvoltage
Voltage rising
5.6
5.45
40
5.8
6.1
V
mV
V
VANAOVP
Voltage falling
5.73
5.96
Hysteresis
Voltage rising
2.51
2.5
2.63
2.6
2.75
2.7
VANA undervoltage
lockout
VANAUVLO
Voltage falling
Buck short-circuit
detection
Threshold
Threshold
280
190
360
300
440
450
mV
mV
LDO short-circuit
detection
LOAD CURRENT MEASUREMENT FOR BUCK REGULATORS
Current measurement
Maximum code
range
10.22
A
Resolution
Measurement accuracy IOUT > 1 A
PFM mode (automatically changing to PWM
LSB
20
mA
<10%
45
4
mode for the measurement)
Measurement time
µs
PWM mode
CURRENT CONSUMPTION
Standby current
consumption, regulators
disabled
9
µA
µA
Active current
consumption, one buck
regulator enabled in
auto mode, internal
RC oscillator, PGOOD
monitoring enabled
IOUT_Bx = 0 mA, not switching
58
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
6.5 Electrical Characteristics (continued)
Limits apply over the junction temperature range –40°C ≤ TJ ≤ +140°C, specified VVANA, VVIN_Bx, VVIN_LDOx, VVOUT_Bx
,
VVOUT_LDOx and IOUT range, unless otherwise noted. Typical values are at TJ = 25°C, VVANA = VVIN_Bx = VVIN_LDOx = 3.7 V,
and VOUT = 1 V, unless otherwise noted(1) (2)
.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
Active current
consumption, two buck
regulators enabled in
auto mode, internal
RC oscillator, PGOOD
monitoring enabled
IOUT_Bx = 0 mA, not switching
100
µA
Active current
consumption during
PWM operation, one
buck regulator enabled
IOUT_Bx = 0 mA
15
30
mA
mA
Active current
consumption during
PWM operation, two
buck regulators enabled
IOUT_Bx = 0 mA
Additional current consumption per LDO,
IOUT_LDOx = 0 mA
LDO regulator enabled
86
2
µA
PLL and clock detector
current consumption
fEXT_CLK = 1 MHz, Additional current
consumption when enabled
mA
DIGITAL INPUT SIGNALS EN, SCL, SDA, CLKIN
VIL
VIH
Input low level
Input high level
0.4
V
1.2
10
Hysteresis of Schmitt
Trigger inputs
VHYS
80
200
mV
kΩ
EN/CLKIN pulldown
resistance
EN_PD/CLKIN_PD = 1
500
DIGITAL OUTPUT SIGNALS nINT, SDA
nINT: ISOURCE = 2 mA
SDA: ISOURCE = 20 mA
0.4
0.4
V
V
VOL
RP
Output low level
External pullup resistor
for nINT
To VIO Supply
10
kΩ
DIGITAL OUTPUT SIGNALS PGOOD, GPO, GPO2
VOL
VOH
Output low level
ISOURCE = 2 mA
ISINK = 2 mA
0.4
V
V
Output high level,
configured to push-pull
VVANA – 0.4
VVANA
Supply voltage for
VPU
external pullup resistor,
configured to open-drain
VVANA
V
External pullup resistor,
configured to open-drain
RPU
10
kΩ
ALL DIGITAL INPUTS
ILEAK Input current
All logic inputs over pin voltage range
−1
1
µA
(1) All voltage values are with respect to network ground.
(2) Minimum (MIN) and Maximum (MAX) limits are specified by design, test, or statistical analysis. Typical (TYP) numbers are not verified,
but do represent the most likely norm.
(3) The maximum output current can be limited by the forward current limit ILIM FWD. The power dissipation inside the die increases the
junction temperature and limits the maximum current depending of the length of the current pulse, efficiency, board and ambient
temperature.
(4) The slew-rate can be limited by the current limit (forward or negative current limit), output capacitance and load current.
(5) The final PFM-to-PWM and PWM-to-PFM switchover current varies slightly and is dependent on the output voltage, input voltage and
the inductor current level.
(6) The external clock frequency must be selected so that buck switching frequency is above 1.7 MHz.
Copyright © 2021 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
6.6 I2C Serial Bus Timing Parameters
These specifications are ensured by design. Unless otherwise noted, VIN_Bx = 3.7 V (see (1)). See 图 6-1 for details about the
I2C-Compatible Timing diagram.
MIN
MAX
100
400
1
UNIT
Standard mode
kHz
Fast mode
fSCL
Serial clock frequency
Fast mode+
High-speed mode, Cb = 100 pF
High-speed mode, Cb = 400 pF
Standard mode
3.4
1.7
MHz
µs
4.7
1.3
0.5
0.16
0.32
4
Fast mode
tLOW
SCL low time
Fast mode+
High-speed mode, Cb = 100 pF
High-speed mode, Cb = 400 pF
Standard mode
Fast mode
0.6
0.26
0.06
0.12
250
100
50
tHIGH
SCL high time
Data setup time
Data hold time
Fast mode+
µs
ns
ns
µs
High-speed mode, Cb = 100 pF
High-speed mode, Cb = 400 pF
Standard mode
Fast mode
tSU;DAT
tHD;DAT
tSU;STA
Fast mode+
High-speed mode
Standard mode
10
10
3450
900
Fast mode
10
Fast mode+
10
High-speed mode, Cb = 100 pF
High-speed mode, Cb = 400 pF
Standard mode
10
70
10
150
4.7
0.6
0.26
0.16
4
Setup time for a start
or a repeated start
condition
Fast mode
Fast mode+
High-speed mode
Standard mode
Fast mode
0.6
0.26
0.16
4.7
1.3
0.5
4
Hold time for a start or a
repeated start condition
tHD;STA
µs
µs
µs
Fast mode+
High-speed mode
Standard mode
Bus free time between a
stop and start condition
tBUF
Fast mode
Fast mode +
Standard mode
Fast mode
0.6
0.26
0.16
Setup time for a stop
condition
tSU;STO
Fast mode+
High-speed mode
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
6.6 I2C Serial Bus Timing Parameters (continued)
These specifications are ensured by design. Unless otherwise noted, VIN_Bx = 3.7 V (see (1)). See 图 6-1 for details about the
I2C-Compatible Timing diagram.
MIN
MAX
1000
300
120
80
UNIT
Standard mode
Fast mode
20
trDA
Rise time of SDA signal Fast mode+
ns
High-speed mode, Cb = 100 pF
10
20
High-speed mode, Cb = 400 pF
Standard mode
160
300
20 × (VDD / 5.5
V)
Fast mode
300
120
tfDA
Fall time of SDA signal
20 × (VDD / 5.5
V)
ns
Fast mode+
High-speed mode, Cb = 100 pF
High-speed mode, Cb = 400 pF
Standard mode
10
30
80
160
1000
300
120
40
Fast mode
20
trCL
Rise time of SCL signal Fast mode+
High-speed mode, Cb = 100 pF
ns
ns
10
20
10
High-speed mode, Cb = 400 pF
80
Rise time of SCL signal High-speed mode, Cb = 100 pF
after a repeated start
80
trCL1
condition and after an
acknowledge bit
High-speed mode, Cb = 400 pF
20
160
Standard mode
Fast mode
300
300
20 × (VDD / 5.5
V)
tfCL
Fall time of a SCL signal
20 × (VDD / 5.5
V)
ns
Fast mode+
120
High-speed mode, Cb = 10 – 100 pF
High-speed mode, Cb = 400 pF
10
20
40
80
Capacitive load for each
bus line (SCL and SDA)
Cb
400
50
pF
ns
Pulse width of spike
suppressed (SCL and
SDA spikes that are less
then the indicated width
are suppressed)
Standard mode, fast mode, and fast mode+
High-speed mode
tSP
10
(1) Cb refers to the capacitance of one bus line.
Copyright © 2021 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
tBUF
SDA
tHD;STA
trCL
tfDA
trDA
tSP
tLOW
tfCL
SCL
tHD;STA
tSU;STA
tSU;STO
tHIGH
tHD;DAT
S
tSU;DAT
S
RS
P
START
REPEATED
START
STOP
START
图 6-1. I2C-Compatible Timing
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
6.7 Typical Characteristics
Unless otherwise specified: V(VIN_Bx) = V(VIN_LDOx) = V(VANA) = 3.7 V, VOUT_Bx = 1 V, VOUT_LDO = 1 V, TA = 25°C, L = 0.47 µH
(TOKO DFE252012PD-R47M), COUT_BUCK = 22 µF , CPOL_BUCK = 22 µF, and COUT_LDO = 1 µF.
15
14
13
12
11
10
9
70
68
66
64
62
60
58
56
54
52
50
8
7
6
5
2.5
3
3.5
4
Input Voltage (V)
4.5
5
5.5
2.5
3
3.5
4
Input Voltage (V)
4.5
5
5.5
D101
D102
Regulators disabled
VOUT_Bx = 1 V
Load = 0 mA
图 6-2. Standby Current Consumption vs Input Voltage
图 6-3. Active State Current Consumption vs Input Voltage, One
Buck Regulator Enabled in PFM Mode
24
22
20
18
16
14
12
10
8
100
98
96
94
92
90
88
86
84
82
80
6
4
2.5
3
3.5
4
Input Voltage (V)
4.5
5
5.5
2.5
3
3.5
4
Input Voltage (V)
4.5
5
5.5
D103
D104
VOUT_Bx = 1 V
Load = 0 mA
VOUT_LDOx = 1 V
Load = 0 mA
图 6-4. Active State Current Consumption vs Input Voltage, One 图 6-5. Active State Current Consumption vs Input Voltage, One
Buck Regulator Enabled in Forced PWM Mode
LDO Regulator Enabled
Copyright © 2021 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
7 Detailed Description
7.1 Overview
The LP87332D-Q1 is a high-efficiency, high-performance flexible power supply device with two step-down
DC/DC converter cores (Buck0 and Buck1) and two low-dropout (LDO) linear regulators (LDO0 and LDO1) for
automotive applications. 表 7-1 lists the output characteristics of the regulators.
表 7-1. Supply Specification
OUTPUT
SUPPLY
VOUT RANGE (V)
RESOLUTION (mV)
10 (0.7 V to 0.73 V)
IMAX MAXIMUM OUTPUT CURRENT (mA)
Buck0
Buck1
0.7 to 3.36
5 (0.73 V to 1.4 V)
20 (1.4 V to 3.36 V)
3000
10 (0.7 V to 0.73 V)
5 (0.73 V to 1.4 V)
20 (1.4 V to 3.36 V)
0.7 to 3.36
3000
LDO0
LDO1
0.8 to 3.3
0.8 to 3.3
100
100
300
300
The LP87332D-Q1 also supports switching clock synchronization to an external clock (CLKIN pin). The nominal
frequency of the external clock can be from 1 MHz to 24 MHz with 1-MHz steps.
Additional features include:
•
•
Soft-start
Input voltage protection:
– Undervoltage lockout
– Overvoltage protection
Output voltage monitoring and protection:
– Overvoltage monitoring
– Undervoltage monitoring
– Overload protection
Thermal warning
•
•
•
Thermal shutdown
The LP87332D-Q1 has one dedicated general purpose digital output (GPO) signal. The CLKIN pin can be
programmed as a second GPO signal (GPO2), if the external clock is not needed. The output type (open-drain
or push-pull) is programmable for the GPOs.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
7.2 Functional Block Diagram
VANA
nINT
Interrupts
Buck0
ILIM Det
Pwrgood Det
Enable
and Disable,
Delay
Control
Slew-Rate
Control
Overload and
SC Det
EN
Iload ADC
GPO
Buck1
ILIM Det
Pwrgood Det
SDA
SCL
I2C
Overload and
SC Det
Iload ADC
OTP
EPROM
Registers
LDO0
PGOOD
ILIM Det
Pwrgood Det
Overload
Digital
Logic
and SC Det
Thermal
Monitor
UVLO
LDO1
ILIM Det
Pwrgood Det
Overload
SW
Reset
Ref &
Bias
Oscillator
and SC Det
CLKIN (GPO2)
Copyright © 2016, Texas Instruments Incorporated
7.3 Feature Description
7.3.1 DC/DC Converters
7.3.1.1 Overview
The LP87332D-Q1 includes two step-down DC/DC converter cores. The cores are designed for flexibility;
most of the functions are programmable, thus giving a possibility to optimize the regulator operation for each
application. The buck regulators deliver 0.7-V to 3.36-V regulated voltage rails from a 2.8-V to 5.5-V supply
voltage.
The LP87332D-Q1 has the following features:
•
•
•
•
•
•
•
•
•
•
•
•
DVS support with programmable slew rate
Automatic mode control based on the loading (PFM or PWM mode)
Forced PWM mode option
Optional external clock input to minimize crosstalk
Optional spread-spectrum technique to reduce EMI
Phase control for optimized EMI
Synchronous rectification
Current mode loop with PI compensator
Soft start
Power Good flag with maskable interrupt
Power Good signal (PGOOD) with selectable sources
Average output current sensing (for PFM entry and load current measurement)
Copyright © 2021 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
The following parameters can be programmed through the registers, the default values are set by OTP bits:
•
•
•
•
•
Output voltage
Forced PWM operation
Switch current limit
Output voltage slew rate
Enable and disable delays
There are two modes of operation for the buck converter, depending on the output current required: pulse-width
modulation (PWM) and pulse-frequency modulation (PFM). The converter operates in PWM mode at high load
currents of approximately 600 mA or higher. Lighter output current loads cause the converter to automatically
switch into PFM mode for reduced current consumption when forced PWM mode is disabled. The forced PWM
mode can be selected to maintain fixed switching frequency at all load current levels.
A block diagram of a single core is shown in 图 7-1.
HS FET
CURRENT
SENSE
VIN
FB
POS
CURRENT
LIMIT
RAMP
GENERATOR
V
OUT
-
GATE
CONTROL
ERROR
AMP
SW
+
LOOP
COMP
VOLTAGE
SETTING
SLEW RATE
CONTROL
NEG
CURRENT
LIMIT
POWER
GOOD
+
-
VDAC
ZERO
CROSS
DETECT
LS FET
CURRENT
SENSE
MASTER
INTERFACE
PROGRAMMABLE
PARAMETERS
CONTROL
BLOCK
SLAVE
INTERFACE
IADC
GND
Copyright © 2016, Texas Instruments Incorporated
图 7-1. Detailed Block Diagram Showing One Core
7.3.1.2 Transition Between PWM and PFM Modes
The PWM mode operation optimizes efficiency at mid to full load at the expense of light-load efficiency. The
LP87332D-Q1 converter operates in the PWM mode at load current of about 600 mA or higher. At lighter load
current levels the device automatically switches into the PFM mode for reduced current consumption when
forced PWM mode is disabled (AUTO mode operation). By combining the PFM and the PWM modes, a high
efficiency is achieved over a wide output-load current range.
7.3.1.3 Buck Converter Load Current Measurement
The buck load current can be monitored through I2C registers. The monitored buck converter is selected with
the LOAD_CURRENT_BUCK_SELECT bit in the SEL_I_LOAD register. A write to this selection register starts a
current measurement sequence. The regulator is automatically forced to the PWM mode for the measurement
period. The measurement sequence is 50 µs long, maximum.
The LP87332D-Q1 device can be configured to give out an interrupt (the I_MEAS_INT bit in the INT_TOP_1
register) after the load current measurement sequence is finished. The load current measurement interrupt can
be masked with the I_MEAS_MASK bit (TOP_MASK_1 register). The measurement result can be read from
the registers I_LOAD_1 and I_LOAD_2. The register I_LOAD_1 bits BUCK_LOAD_CURRENT[7:0] gives out the
LSB bits, and the register I_LOAD_2 bit BUCK_LOAD_CURRENT[8] gives out the MSB bit. The measurement
result BUCK_LOAD_CURRENT[8:0] LSB is 20 mA, and the maximum code value of the measurement
corresponds to 10.22 A.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
7.3.1.4 Spread-Spectrum Mode
Systems with periodic switching signals may generate a large amount of switching noise in a set of narrowband
frequencies (the switching frequency and its harmonics). The usual solution to reduce noise coupling is to
add EMI-filters and shields to the boards. The LP87332D-Q1 has a register-selectable spread-spectrum mode
which minimizes the need for output filters, ferrite beads, or chokes. In spread spectrum mode, the switching
frequency varies around the center frequency, reducing the EMI emissions radiated by the converter and
associated passive components and PCB traces (see Spread-Spectrum Modulation). Spread-spectrum mode is
only available when an internal RC oscillator is used (EN_PLL bit is 0 in PLL_CTRL register), it is enabled with
the EN_SPREAD_SPEC bit in the CONFIG register, and it affects both buck cores.
Frequency
Where a fixed frequency converter exhibits large amounts of spectral energy at the switching frequency, the spread spectrum
architecture of the LP87332D-Q1 spreads that energy over a large bandwidth.
图 7-2. Spread-Spectrum Modulation
7.3.2 Sync Clock Functionality
The LP87332D-Q1 device contains a CLKIN input to synchronize the switching clock of the buck regulators
with the external clock. The block diagram of the clocking and PLL module is shown in 图 7-3. Depending on
the EN_PLL bit in the PLL_CTRL register and the external clock availability, the external clock is selected and
interrupt is generated as shown in 表 7-2. The interrupt can be masked with the SYNC_CLK_MASK bit in the
TOP_MASK_1 register. The nominal frequency of the external input clock is set by the EXT_CLK_FREQ[4:0]
bits in the PLL_CTRL register, and it can be from 1 MHz to 24 MHz with 1-MHz steps. The external clock must
be inside accuracy limits (–30%/+10%) of the selected frequency for valid clock detection.
The SYNC_CLK_INT interrupt in the INT_TOP_1 register is also generated in cases where the external clock
is expected but is not available. These cases occur when EN_PLL is 1 during start-up (read OTP-to-standby
transition) and during Buck regulator enable (standby-to-active transition).
Copyright © 2021 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
24 MHz
RC
Oscillator
Internal
24 MHz
clock
CLKIN
Detector
Divider
“EXT_CLK
_FREQ“
Clock Select
Logic
1 MHz
CLKIN
24 MHz
PLL
“EN_PLL“
1 MHz
Divider
24
图 7-3. Clock and PLL Module
表 7-2. PLL Operation
DEVICE
OPERATION MODE
PLL AND CLOCK
DETECTOR STATE
INTERRUPT FOR
EXTERNAL CLOCK
EN_PLL
CLOCK
STANDBY
0
Disabled
Disabled
No
Internal RC
Internal RC
ACTIVE
0
1
No
When external clock
appears or disappears
Automatic change to external
clock when available
STANDBY
ACTIVE
Enabled
Enabled
When external clock
appears or disappears
Automatic change to external
clock when available
1
7.3.3 Low-Dropout Linear Regulators (LDOs)
The LP87332D-Q1 device includes two identical linear regulators, LDO0 and LDO1, which target analog loads
with low noise requirements. The LDO regulators deliver 0.8-V to 3.3-V regulated voltage rails from a 2.5-V to
5.5-V input voltage. Both regulators have dedicated inputs which can be higher or lower than the device system
voltage V(VANA) to minimize the power dissipation.
7.3.4 Power-Up
The power-up sequence for the LP87332D-Q1 is as follows:
•
The VANA and VIN_Bx reach minimum recommended levels (VVANA > VANAUVLO). This initiates power-on-
reset (POR), OTP reading, and enables the system I/O interface. The I2C host should allow at least 1.2 ms
before writing or reading data to the LP87332D-Q1.
•
•
•
•
The device enters standby mode.
The host can change the default register setting by I2C if needed.
The regulators can be enabled and disabled.
The GPO signals can be controlled by the EN pin and the I2C interface.
Transitions between the operating modes are shown in 节 7.4.1.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
7.3.5 Regulator Control
7.3.5.1 Enabling and Disabling Regulators
The regulators can be enabled when the device is in STANDBY or ACTIVE state. There are two ways to enable
and disable the buck regulators:
•
Using the BUCKx_EN bit in the BUCKx_CTRL_1 register (the BUCKx_EN_PIN_CTRL bit is 0 in the
BUCKx_CTRL_1 register).
•
Using the EN control pin (the BUCKx_EN bit and the BUCKx_EN_PIN_CTRL bit is 1).
Similarly, there are two ways to enable and disable the LDO regulators:
•
Using the LDOx_EN bit in the LDOx_CTRL register (the LDOx_EN_PIN_CTRL bit is 0 in the LDOx_CTRL
register).
•
Using the EN control pin (the LDOx_EN bit is 1 and the LDOx_EN_PIN_CTRL bit is 1).
If the EN control pin is used for enable and disable, then the following occurs:
•
•
The delay from the control signal rising edge to start-up is set by the BUCKx_STARTUP_DELAY[3:0] bits in
the BUCKx_DELAY register and the LDOx_STARTUP_DELAY[3:0] bits in the LDOx_DELAY register.
The delay from the control signal falling edge to shutdown is set by the BUCKx_SHUTDOWN_DELAY[3:0]
bits in the BUCKx_DELAY register and the LDOx_SHUTDOWN_DELAY[3:0] bits in the LDOx_DELAY
register.
The delays are only valid for the EN signal transitions and not for control with I2C writings to the BUCKx_EN and
the LDOx_EN bits.
The control of the regulator (with 0-ms delays) is shown in 表 7-3.
表 7-3. Regulator Control
BUCKx_EN AND
LDOx_EN
BUCKx_EN_PIN_CTRL AND
LDOx_EN_PIN_CTRL
BUCKx OUTPUT VOLTAGE AND
LDOx OUTPUT VOLTAGE
EN PIN
Enable and disable control
with the BUCKx_EN and the
LDOx_EN bit
0
1
Don't Care
0
Don't Care
Don't Care
Disabled
BUCKx_VSET[7:0] and LDOx_VSET[4:0]
Enable and disable control
with the EN pin
1
1
1
1
Low
Disabled
High
BUCKx_VSET[7:0] and LDOx_VSET[4:0]
The buck regulator is enabled by the EN pin or by I2C writing as shown in 图 7-4. The soft-start circuit
limits the in-rush current during start-up. When the output voltage rises to a 0.35-V level, the output voltage
becomes slew-rate controlled. If there is a short circuit at the output, and the output voltage does not increase
above the 0.35-V level in 1 ms or the output voltage drops below 0.35-V level during operation (for minimum
of 1 ms), then the regulator is disabled, and the BUCKx_SC_INT interrupt in the INT_BUCK register is set.
When the output voltage reaches the Power-Good threshold level, the BUCKx_PG_INT interrupt flag in the
INT_BUCK register is set. The Power-Good interrupt flag, when reaching valid output voltage, can be masked
using the BUCKx_PGR_MASK bit in the BUCK_MASK register. The Power-Good interrupt flag can also be
generated when the output voltage becomes invalid. The interrupt mask for invalid output voltage detection is
set by the BUCKx_PGF_MASK bit in the BUCK_MASK register. A BUCKx_PG_STAT bit in the BUCK_STAT
register always shows the validity of the output voltage; 1 means valid and 0 means invalid output voltage.
A PGOOD_WINDOW_BUCK bit in the PGOOD_CTRL_1 register sets the detection method for the valid buck
output voltage, either undervoltage detection or undervoltage and overvoltage detection.
Copyright © 2021 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
Voltage decrease because of load
Voltage
BUCKx_VSET[7:0]
Powergood
Ramp
BUCKx_CTRL_2(BUCKx_SLEW_RATE[2:0])
0.6V
0.35V
Fast Discharge
Time
Soft start
Enable
0
0
0
1
0
0
1
BUCK_STAT(BUCKx_STAT)
BUCK_STAT(BUCKx_PG_STAT)
INT_BUCK(BUCKx_PG_INT)
nINT
1
1
0
1
1
0
0 1
0
0
Powergood
interrupts
Host clears
interrupts
BUCK_MASK(BUCKx_PGF_MASK) = 0
BUCK_MASK(BUCKx_PGR_MASK) = 0
图 7-4. Buck Regulator Enable and Disable
The LDO regulator is enabled by the EN pin or by I2C writing, as shown in 图 7-5. The soft-start circuit limits
the in-rush current during start-up. The output voltage increase rate is less than 100 mV/μsec during soft-start. If
there is a short circuit at the output, and the output voltage does not increase above the 0.3-V level in 1 ms or
the output voltage drops below 0.3-V level during operation (for minimum of 1 ms), then the regulator is disabled,
and the LDOx_SC_INT interrupt in the INT_LDO register is set. When the output voltage reaches the Power-
Good threshold level, the LDOx_PG_INT interrupt flag in the INT_LDO register is set. The Power-Good interrupt
flag, when reaching valid output voltage, can be masked using the LDOx_PGR_MASK bit in the LDO_MASK
register. The Power-Good interrupt flag can also be generated when the output voltage becomes invalid. The
interrupt mask for invalid output voltage detection is set by the LDOx_PGF_MASK bit in the LDO_MASK register.
A LDOx_PG_STAT bit in the LDO_STAT register always shows the validity of the output voltage; 1 means
valid, and 0 means invalid output voltage. A PGOOD_WINDOW_LDO bit in the PGOOD_CTRL_1 register
sets the detection method for the valid LDO output voltage, either undervoltage detection or undervoltage and
overvoltage detection.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
Voltage decrease because of load
Voltage
LDOx_VSET[4:0]
Powergood
Resistive pull-down
(if enabled)
Time
Enable
LDO_STAT(LDOx_STAT)
LDO_STAT(LDOx_PG_STAT)
INT_LDO(LDOx_PG_INT)
nINT
0
0
0
1
0
0
1
1
0
1
1
1
0
0 1
0
0
Powergood
interrupts
Host clears
interrupts
LDO_MASK(LDOx_PGF_MASK) = 0
LDO_MASK(LDOx_PGR_MASK) = 0
图 7-5. LDO Regulator Enable and Disable
The EN input pin has an integrated pulldown resistor. The pulldown resistor is controlled with the EN_PD bit in
the CONFIG register.
7.3.5.2 Changing Output Voltage
The output voltage of the regulator can be changed by writing to the BUCKx_VOUT and LDOx_VOUT register.
The voltage change for the buck regulator is always slew-rate controlled, and the slew-rate is defined by the
BUCKx_SLEW_RATE[2:0] bits in the BUCKx_CTRL_2 register. During voltage change, the forced PWM mode
is used automatically. When the programmed output voltage is achieved, the mode becomes the one defined by
the load current, the BUCKx_FPWM bit in the BUCKx_CTRL_1 register.
The voltage change and Power-Good interrupts are shown in 图 7-6.
Copyright © 2021 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
Ramp for Buck
BUCKx_CTRL2(SLEW_RATEx[2:0])
Voltage
BUCKx_VSET /
LDOx_VSET
Powergood
Powergood
Time
BUCK_STAT(BUCKx_STAT) /
LDO_STAT(LDOx_STAT)
1
1
0
BUCK_STAT(BUCKx_PG_STAT) /
LDO_STAT(LDOx_PG_STAT)
0
1
1
0
1
1
INT_BUCK(BUCKx_PG_INT) /
INT_LDO(LDOx_PG_INT)
0
0
nINT
Powergood
interrupt
Host clears
interrupt
Powergood
interrupt
Host clears
interrupt
BUCK_MASK(BUCKx_PGF_MASK)=0
BUCK_MASK(BUCKx_PGR_MASK)=0
LDO_MASK(LDOx_PGF_MASK)=0
LDO_MASK(LDOx_PGR_MASK)=0
图 7-6. Regulator Output Voltage Change
During an LDO voltage change, the internal reference for the Power-Good detection is also changed. For this
reason when the output voltage is changing, toggling of the Power-Good signal may still indicate a valid output.
This period takes less than 100 µs and after that time the Power-Good gives correct value.
7.3.6 Enable and Disable Sequences
The LP87332D-Q1 device supports start-up and shutdown sequencing with programmable delays for different
regulator outputs using a single EN control signal. The Buck regulator is selected for delayed control with:
•
•
•
•
The BUCKx_EN = 1 in the BUCKx_CTRL_1 register
The BUCKx_EN_PIN_CTRL = 1 in the BUCKx_CTRL_1 register
The BUCKx_VSET[7:0] bits in the BUCKx_VOUT register defines the voltage when the EN pin is high
The delay from the rising edge of the EN pin to the regulator enable is set by the
BUCKx_STARTUP_DELAY[3:0] bits in the BUCKx_DELAY register.
The delay from the falling edge of the EN pin to the regulator disable is set by the
BUCKx_SHUTDOWN_DELAY[3:0] bits in the BUCKx_DELAY register.
•
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
In the same way, the LDO regulator is selected for delayed control with:
•
•
•
•
The LDOx_EN = 1 in the LDOx_CTRL register
The LDOx_EN_PIN_CTRL = 1 in the LDOx_CTRL register
The LDOx_VSET[4:0] bits in the LDOx_VOUT register defines the voltage when the EN pin is high
The delay from the rising edge of the EN pin to the regulator enable is set by the
LDOx_STARTUP_DELAY[3:0] bits in the LDOx_DELAY register.
•
The delay from the falling edge of the EN pin to the regulator disable is set by the
LDOx_SHUTDOWN_DELAY[3:0] bits in the LDOx_DELAY register.
The GPO and GPO2 digital output signals can be also controlled as a part of start-up and shutdown sequencing
with the following settings:
•
•
•
GPOx_EN = 1 in GPO_CTRL register
GPOx_EN_PIN_CTRL = 1 in GPO_CTRL register
The delay from the rising edge of the EN pin to the rising edge of the GPO or GPO2 signal is set by the
GPOx_STARTUP_DELAY[3:0] bits in the GPOx_DELAY register.
The delay from the falling edge of the EN pin to the falling edge of the GPO or GPO2 signal is set by the
GPOx_SHUTDOWN_DELAY[3:0] bits in the GPOx_DELAY register.
•
An example of the start-up and shutdown sequences for the buck regulators are shown in 图 7-7. The start-up
and shutdown delays for the Buck0 regulator are 1 ms and 4 ms, and for the Buck1 regulator the start-up and
shutdown delays are 3 ms and 1 ms. The delay settings are only used for enable or disable control with the EN
signal.
Typical sequence
EN
EN_BUCK0
EN_BUCK1
1 ms
4 ms
3 ms
1 ms
Sequence with short EN low and high periods
EN
Startup cntr
0
0
0
1
0
1
2
3
4
5
6
0
2
Shutdown cntr
EN_BUCK0
EN_BUCK1
0
1
0
1
0
1
2
3
4
5
1 ms
4 ms
3 ms
1 ms
图 7-7. Start-Up and Shutdown Sequencing
Copyright © 2021 Texas Instruments Incorporated
24
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
7.3.7 Device Reset Scenarios
There are two reset methods implemented on the LP87332D-Q1:
•
•
Software reset with the SW_RESET bit in the RESET register.
Undervoltage lockout (UVLO) reset from the VANA supply.
An software reset occurs when 1 is written to the SW_RESET bit. The bit is automatically cleared after writing.
This event disables all the regulators immediately, drives the GPO or GPO2 signals low, resets all the register
bits to the default values, and loads the OTP bits (see 图 7-13). The I2C interface is not reset during a software
reset.
If the VANA supply voltage falls below the UVLO threshold level, then all the regulators are disabled
immediately, the GPO or GPO2 signals are driven low, and all the register bits are reset to the default values.
When the VANA supply voltage transitions above the UVLO threshold level, an internal POR occurs. The OTP
bits are loaded to the registers and a startup is initiated according to the register settings.
7.3.8 Diagnosis and Protection Features
The LP87332D-Q1 is capable of providing four levels of protection features:
•
•
•
•
Information of valid regulator output voltage, which sets the interrupt or PGOOD signal.
Warnings for diagnosis, which sets the interrupt.
Protection events, which are disabling the regulators.
Faults, which are causing the device to shutdown.
The LP87332D-Q1 sets the flag bits indicating what protection or warning conditions have occurred, and the
nINT pin is pulled low. The nINT is released again after a clear of flags is complete. The nINT signal stays low
until all the pending interrupts are cleared.
When a fault is detected or software requested reset, it is indicated by a RESET_REG_INT interrupt flag in
the INT_TOP_2 register after next start-up. If the RESET_REG_MASK is set to masked in the OTP, then the
interrupt is not generated. The mask bit change with I2C does not affect, because the RESET_REG_MASK bit is
loaded from the OTP during reset sequence.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
25
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
表 7-4. Summary of Interrupt Signals
RECOVERY AND INTERRUPT
CLEAR
EVENT
DEVICE RESPONSE
INTERRUPT BIT
INTERRUPT MASK BIT
STATUS BIT
Write 1 to the BUCKx_ILIM_INT
bit.
Interrupt is not cleared if the
current limit is active
BUCK_INT
BUCKx_ILIM_INT
Buck current limit triggered
No effect
BUCKx_ILIM_MASK
BUCKx_ILIM_STAT
Write 1 to the LDOx_ILIM_INT bit
Interrupt is not cleared if the
current limit is active
LDO_INT
LDOx_ILIM_INT
LDO current limit triggered
No effect
LDOx_ILIM_MASK
N/A
LDOx_ILIM_STAT
N/A
Buck short circuit (VVOUT
<
0.35 V at 1 ms after enable)
BUCK_INT
BUCKx_SC_INT
or overload (VVOUT decreasing Regulator disable
below 0.35 V during operation,
1-ms debounce)
Write 1 to the BUCKx_SC_INT bit
Write 1 to the LDOx_SC_INT bit
LDO short circuit (VVOUT
<
0.3 V at 1 ms after enable)
LDO_INT
LDOx_SC_INT
or overload (VVOUT decreasing Regulator disable
below 0.3 V during operation,
1-ms debounce)
N/A
N/A
Write 1 to tge TDIE_WARN_INT
bit
Thermal warning
No effect
TDIE_WARN_INT
TDIE_WARN_MASK
TDIE_WARN_STAT
Interrupt is not cleared if the
temperature is above the thermal
warning level
All the regulators are
disabled immediately, and
the GPO and GPO2 are
set to low
Write 1 to the TDIE_SD_INT bit
Interrupt is not cleared if the
temperature is above the thermal
shutdown level
Thermal shutdown
TDIE_SD_INT
OVP_INT
N/A
N/A
TDIE_SD_STAT
OVP_STAT
All the regulators are
disabled immediately, and
the GPO and GPO2 are
set to low
Write 1 to the OVP_INT bit
Interrupt is not cleared if the VANA
voltage is above the VANAOVP
level
VANA overvoltage (VANAOVP
)
Buck power good, output
voltage becomes valid
BUCK_INT
BUCKx_PG_INT
No effect
BUCKx_PGR_MASK
BUCKx_PGF_MASK
LDOx_PGR_MASK
LDOx_PGF_MASK
PGOOD_MASK
BUCKx_PG_STAT
BUCKx_PG_STAT
LDOx_PG_STAT
LDOx_PG_STAT
PGOOD_STAT
SYNC_CLK_STAT
N/A
Write 1 to the BUCKx_PG_INT bit
Write 1 to the BUCKx_PG_INT bit
Write 1 to the LDOx_PG_INT bit
Write 1 to the LDOx_PG_INT bit
Write 1 to the PGOOD_INT bit
Write 1 to the SYNC_CLK_INT bit
Write 1 to the I_MEAS_INT bit
Buck power good, output
voltage becomes invalid
BUCK_INT
BUCKx_PG_INT
No effect
LDO Power good, output
voltage becomes valid
LDO_INT
LDOx_PG_INT
No effect
LDO power good, output
voltage becomes invalid
LDO_INT
LDOx_PG_INT
No effect
PGOOD pin changing from
active to inactive state(1)
No effect
PGOOD_INT
External clock appears or
disappears
No effect to regulators
No effect
SYNC_CLK_INT(2)
I_MEAS_INT
SYNC_CLK_MASK
I_MEAS_MASK
Load current measurement is
ready
Immediate shutdown and
the registers reset to
default values
Supply voltage VANAUVLO
triggered (VANA falling)
N/A
N/A
N/A
N/A
N/A
Startup and the registers
reset to default values
and the OTP bits are
loaded
Supply voltage VANAUVLO
triggered (VANA rising)
Write 1 to the RESET_REG_INT
bit
RESET_REG_INT
RESET_REG_MASK
Immediate shutdown is
followed by power up and
the registers are reset to
their default values
Write 1 to the RESET_REG_INT
bit
Software requested reset
RESET_REG_INT
RESET_REG_MASK
N/A
(1) The PGOOD_STAT bit is 1 when the PGOOD pin shows valid voltages. The PGOOD_POL bit in the PGOOD_CTRL_1 register affects
only the PGOOD pin polarity, not the Power Good and PGOOD_INT interrupt polarity.
(2) If the clock is not available when the clock detector is enabled, then an interrupt is generated during the clock-dector operation.
Copyright © 2021 Texas Instruments Incorporated
26
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
7.3.8.1 Power-Good Information (PGOOD pin)
In addition to the interrupt-based indication of the current limit and the Power-Good level, the LP87332D-Q1
device supports monitoring with PGOOD signal:
•
•
•
•
Regulator output voltage
Input supply overvoltage
Thermal warning
Thermal shutdown
The regulator output voltage monitoring (not current limit monitoring) can be selected for the PGOOD indication.
This selection is individual for both buck regulators and LDO regulators, and is set by the EN_PGOOD_BUCKx
bits in the PGOOD_CTRL_1 register and the EN_PGOOD_LDOx bits in the PGOOD_CTRL_1 register. When
a regulator is disabled, the monitoring is automatically masked to prevent it forcing the PGOOD inactive. A
thermal warning can also be selected for the PGOOD indication with the EN_PGOOD_TWARN bit in the
PGOOD_CTRL_2 register. The monitoring from all the output rails, thermal warning (TDIE_WARN_STAT),
input overvoltage interrupt (OVP_INT), and thermal shutdown interrupt (TDIE_SD_INT) are combined, and the
PGOOD pin is active only if all the selected sources shows a valid status.
The type of output voltage monitoring for the PGOOD signal is selected by the PGOOD_WINDOW_x bits in the
PGOOD_CTRL_1 register. If the bit is 0, only undervoltage is monitored; if the bit is 1, both undervoltage and
overvoltage are monitored.
The polarity and the output type (push-pull or open-drain) are selected by the PGOOD_POL and PGOOD_OD
bits in the PGOOD_CTRL_1 register.
The PGOOD is only active and asserted when all enabled power resource output voltages are within specified
tolerance for each requested and programmed output voltage.
The PGOOD is inactive and de-asserted if any enabled power resource output voltages is outside specified
tolerance for each requested and programmed output voltage.
The device OTP setting selects either gated (or unusual) or continuous (or invalid) mode of operation.
7.3.8.1.1 PGOOD Pin Gated Mode
The gated (or unusual) mode of operation is selected by setting the PGOOD_MODE bit to 0 in the
PGOOD_CTRL_2 register.
For the gated mode of operation, the PGOOD behaves as follows:
•
•
PGOOD is set to active or asserted state upon exiting the OTP configuration as an initial default state.
PGOOD status is suspended or unchanged during an 800-µs gated time period, thereby gating-off the status
indication.
•
•
During normal power-up sequencing and requested voltage changes, the PGOOD state is not changed
during an 800-µs gated time period. It typically remains active or asserted for normal conditions.
During an abnormal power-up sequencing and requested voltage changes, the PGOOD status could change
to inactive or de-asserted after an 800-µs gated time period if any output voltage is outside of regulation
range.
•
Using the gated mode of operation could allow the PGOOD signal to initiate an immediate power
shutdown sequence if the PGOOD signal is wired-OR with signal connected to the EN input. This type of
circuit configuration provides a smart PORz function for processor that eliminates the need for additional
components to generate PORz upon start-up and to monitor voltage levels of key voltage domains.
Each detected fault sets the correcting fault bit in the PG_FAULT register to 1. The detected fault must be
cleared to continue the PGOOD monitoring. The overvoltage and thermal shutdown are cleared by writing 1
to the OVP_INT and TDIE_SD_INT interrupt bits in the INT_TOP_1 register. The regulator fault is cleared by
writing 1 to the corresponding register bit in the PG_FAULT register. The interrupts can also be cleared with the
VANA UVLO by toggling the input supply. An example of the PGOOD pin operation in gated mode is shown in 图
7-8.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
27
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
V(VANA)
VANA_UVLO
Read
OTP
Shutdown
Standby
State
PGOOD pin
Active
Clear fault
EN pin
4 ms
Buck internal enable
VOUT (Buck1)
800 µs Timer
Buck1 internal powergood
LDO0 internal enable
2 ms
800 µs Timer
VOUT (LDO0)
LDO0 internal powergood
图 7-8. PGOOD Pin Operation in Gated Mode
7.3.8.1.2 PGOOD Pin Continuous Mode
The continuous (or invalid) mode of operation is selected by setting the PGOOD_MODE bit to 1 in the
PGOOD_CTRL_2 register.
For the continuous mode of operation, PGOOD behaves as follows:
•
•
•
•
PGOOD is set to active or asserted state upon exiting OTP configuration.
PGOOD is set to inactive or de-asserted as soon as the regulator is enabled.
PGOOD status begins indicating output voltage regulation status immediately and continuously.
During power-up sequencing and requested voltage changes, PGOOD will toggle between inactive or
de-asserted while output voltages are outside of regulation ranges and active or asserted when inside of
regulation ranges.
The PG_FAULT register bits are latched, and maintain the fault information until the host clears the fault bit by
writing 1 to the bit. The PGOOD signal also indicates a thermal shutdown and input overvoltage interrupts, which
are cleared by clearing the interrupt bits.
When the regulator voltage is transitioning from one target voltage to another, the PGOOD signal becomes
inactive.
7.3.8.1.3 PGOOD Pin Inactive Mode
When the PGOOD signal becomes inactive, the source for the fault can be read from the PG_FAULT register.
If the invalid output voltage becomes valid again, then the PGOOD signal becomes active. Thus the PGOOD
signal always shows if the monitored output voltages are valid. The block diagram for this operation is shown in
图 7-9 and an example of operation is shown in 图 7-10.
The PGOOD signal can also be configured so that it maintains an inactive state even when the monitored
outputs are valid, but there are PG_FAULT_x bits in the PG_FAULT register pending clearance. This type of
operation is selected by setting the PGFAULT_GATES_PGOOD bit to 1 in the PGOOD_CTRL_2 register.
Copyright © 2021 Texas Instruments Incorporated
28
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
EN_PGOOD
_BUCK0
Power Good
Buck0
Buck1
LDO0
LDO1
EN_PGOOD
_BUCK1
Power Good
EN_PGOOD
_LDO0
Power Good
PGOOD
Active High
EN_PGOOD
_LDO1
Power Good
EN_PGOOD
_TWARN
TDIE_WARN_STAT
TDIE_SD_INT
OVP_INT
Copyright © 2016, Texas Instruments Incorporated
图 7-9. PGOOD Block Diagram (Continuous Mode)
V(VANA)
VANA_UVLO
Read
OTP
Standby
State Shutdown
Active
PGOOD pin
EN pin
Buck1 internal enable
VOUT (Buck1)
4 ms
Buck1 internal powergood
LDO0 internal enable
2 ms
VOUT (LDO0)
LDO0 internal powergood
图 7-10. PGOOD Pin Operation in Continuous Mode
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
29
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
7.3.8.2 Warnings for Diagnosis (Interrupt)
7.3.8.2.1 Output Power Limit
The Buck regulators have programmable output peak current limits. The limits are individually programmed for
both regulators with the BUCKx_ILIM[2:0] bits in the BUCKx_CTRL_2 register. If the load current is increased so
that the current limit is triggered, then the regulator continues to regulate at the limit current level (peak current
regulation). The voltage may decrease if the load current is higher than the limit current. If the current regulation
continues for 20 µs, than the LP87332D-Q1 device sets the BUCKx_ILIM_INT bit in the INT_BUCK register and
pulls the nINT pin low. The host processor can read the BUCKx_ILIM_STAT bits in the BUCK_STAT register
to see if the regulator is still in peak current regulation mode, and the interrupt is cleared by writing 1 to the
BUCKx_ILIM_INT bit. The current limit interrupt can be masked by setting the BUCKx_ILIM_MASK bit in the
BUCK_MASK register to 1. The Buck overload situation is shown in 图 7-11.
Regulator disabled by
digital
New startup if
enable is valid
Voltage
VOUTx
350 mV
Resistive
pull-down
1 ms
Time
Current
ILIMx
Time
20 µs
0
0
1
1
0
INT_BUCK(BUCKx_ILIM_INT)
INT_BUCK(BUCKx_SC_INT)
BUCK_STAT(BUCKx_STAT)
nINT
1
0
0
1
Host clearing the interrupt by writing to flags
图 7-11. Buck Regulator Overload Situation
The LDO regulators also include current limit circuitry. If the load current is increased so that the current limit
is triggered, the regulator limits the output current to the threshold level. The voltage may decrease if the load
current is higher than the current limit. If the current regulation continues for 20 µs, the LP87332D-Q1 device
sets the LDOx_ILIM_INT bit in the INT_LDO register and pulls the nINT pin low. The host processor can read the
LDOx_ILIM_STAT bits in the LDO_STAT register to see if the regulator is still in current regulation mode and the
interrupt is cleared by writing 1 to the LDOx_ILIM_INT bit. The current limit interrupt can be masked by setting
the LDOx_ILIM_MASK bit in the LDO_MASK register to 1. The LDO overload situation is shown in 图 7-12.
Copyright © 2021 Texas Instruments Incorporated
30
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
Regulator disabled by
digital
New startup if
enable is valid
Voltage
VOUTx
300 mV
Resistive
pull-down
1 ms
Time
Current
ILIMx
Time
20 µs
0
0
1
1
0
0
1
INT_LDO(LDOx_ILIM_INT)
INT_LDO(LDOx_SC_INT)
LDO_STAT(LDOx_STAT)
nINT
1
0
Host clearing the interrupt by writing to flags
图 7-12. LDO Regulator Overload Situation
7.3.8.2.2 Thermal Warning
The LP87332D-Q1 device includes a protection feature against overtemperature by setting an interrupt for the
host processor. The threshold level of the thermal warning is selected with the TDIE_WARN_LEVEL bit in the
CONFIG register.
If the LP87332D-Q1 device temperature increases above the thermal warning level, then the device sets the
TDIE_WARN_INT bit in the INT_TOP_1 register and pulls the nINT pin low. The status of the thermal warning
can be read from the TDIE_WARN_STAT bit in the TOP_STAT register, and the interrupt is cleared by writing 1
to the TDIE_WARN_INT bit. The thermal warning interrupt can be masked by setting the TDIE_WARN_MASK
bit in the TOP_MASK_1 register to 1.
7.3.8.3 Protection (Regulator Disable)
If the regulator is disabled, because of protection or fault (short-circuit protection, overload protection, thermal
shutdown, input overvoltage protection, or UVLO), then the output power FETs are set to high-impedance mode
and the output pulldown resistor is enabled (if enabled with the BUCKx_RDIS_EN bit in the BUCKx_CTRL_1
register and the LDOx_RDIS_EN bit in the LDOx_CTRL register). The turnoff time of the output voltage is
defined by the output capacitance, load current, and resistance of the integrated pull-down resistor. The pull-
down resistors are active as long as the VANA voltage is above approximately a 1.2-V level.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
31
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
7.3.8.3.1 Short-Circuit and Overload Protection
A short-circuit protection feature allows the LP87332D-Q1 to protect itself and the external components against
a short circuit at the output or against overload during start-up. For the buck and LDO regulators, the fault
thresholds are about 350 mV (buck) and 300 mV (LDO). The protection is triggered and the regulator is disabled
if the output voltage is below the threshold level (1 ms) after the regulator is enabled.
In a similar way, the overload situation is protected during normal operation. If the output voltage falls below 0.35
V and 0.3 V and remains below the threshold level for 1 ms, then the regulator is disabled.
In Buck regulator short-circuit and overload situations, the BUCKx_SC_INT bit in the INT_BUCK register and the
INT_BUCKx bit in the INT_TOP_1 register are set to 1, the BUCKx_STAT bit in BUCK_STAT register is set to
0, and the nINT signal is pulled low. In LDO regulator short-circuit and overload situations, the LDOx_SC_INT
bit in the INT_LDO register and the INT_LDOx bit in the INT_TOP_1 register are set to 1, the LDOx_STAT bit in
the LDO_STAT register is set to 0, and the nINT signal is pulled low. The host processor clears the interrupt by
writing 1 to the BUCKx_SC_INT or to the LDOx_SC_INT bit. Upon clearing the interrupt, the regulator makes a
new start-up attempt if the regulator is in an enabled state.
7.3.8.3.2 Overvoltage Protection
The LP87332D-Q1 device monitors the input voltage from the VANA pin in standby and active operation modes.
If the input voltage rises above the VANAOVP voltage level, the following occurs:
•
•
All regulators are disabled immediately (without switching ramp or shutdown delays).
The pull-down resistors discharge the output voltages, if the pull-down resistors are enabled (the
BUCKx_RDIS_EN = 1 in the BUCKx_CTRL_1 register and the LDOx_RDIS_EN = 1 in the LDOx_CTRL
register).
•
•
•
•
The GPOs are set to logic low level.
The nINT signal is pulled low.
The OVP_INT bit in the INT_TOP_1 register is set to 1.
The BUCKx_STAT bit in the BUCK_STAT register and the LDOx_STAT bit in the LDO_STAT register are set
to 0.
The host processor clears the interrupt by writing 1 to the OVP_INT bit. If the input voltage is above the
overvoltage detection level, then the interrupt is not cleared. The host can read the status of the overvoltage
from the OVP_STAT bit in the TOP_STAT register. The regulators cannot be enabled as long as the input
voltage is above the overvoltage detection level or while the overvoltage interrupt is pending.
7.3.8.3.3 Thermal Shutdown
The LP87332D-Q1 has an overtemperature protection function that operates to protect itself from short-term
misuse and overload conditions. When the junction temperature exceeds around 150°C, the regulators are
disabled immediately (without switching ramp and shutdown delays), the TDIE_SD_INT bit in the INT_TOP_1
register is set to 1, the nINT signal is pulled low, and the device enters STANDBY. The nINT is cleared by writing
1 to the TDIE_SD_INT bit. If the temperature is above thermal shutdown level, then the interrupt is not cleared.
The host can read the status of the thermal shutdown from the TDIE_SD_STAT bit in the TOP_STAT register.
The regulators cannot be enabled as long as the junction temperature is above the thermal shutdown level or
while the thermal shutdown interrupt is pending.
Copyright © 2021 Texas Instruments Incorporated
32
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
7.3.8.4 Fault (Power Down)
7.3.8.4.1 Undervoltage Lockout
When the input voltage falls below the VANAUVLO at the VANA pin, the buck and LDO regulators are disabled
immediately (without switching ramp and shutdown delays), the output capacitor is discharged using the
pulldown resistor, and the LP87332D-Q1 device enters SHUTDOWN. When the V(VANA) voltage is above the
VANAUVLO threshold level, the device powers up to STANDBY state.
If the reset interrupt is unmasked by default (OTP bit for RESET_REG_MASK is 0 in TOP_MASK_2 register),
then the RESET_REG_INT interrupt bit in the INT_TOP_2 register indicates that the device has been in
SHUTDOWN. The host processor must clear the interrupt by writing 1 to the RESET_REG_INT bit. If the host
processor reads the RESET_REG_INT interrupt bit after detecting an nINT low signal, then it detects that the
input supply voltage has been below the VANAUVLO level (or the host has requested reset with the SW_RESET
bit in the RESET register), and the registers are reset to default values.
7.3.9 Operation of the GPO Signals
The LP87332D-Q1 device supports up to two general purpose output signals, GPO and GPO2. The GPO2
signal is multiplexed with the CLKIN signal. The selection between the CLKIN and GPO2 pin function is set with
the CLKIN_PIN_SEL bit in the CONFIG register.
The GPO pins are configured with the following bits:
•
The GPOx_OD bit in The GPO_CTRL register defines the type of the output, either push-pull with V(VANA)
level or open drain.
The logic level of the GPOx pin is set by the EN_GPOx bit in the GPO_CTRL register.
The control of the GPOs can be included to start-up and shutdown sequences. The GPO control for a sequence
with an EN pin is selected by the GPOx_EN_PIN_CTRL bit in the GPO_CTRL register. For start-up and
shutdown sequence control, see 节 7.3.6.
7.3.10 Digital Signal Filtering
The digital signals have a debounce filtering. The signal or supply is sampled with a clock signal and a counter.
This results as an accuracy of one clock period for the debounce window.
表 7-5. Digital Signal Filtering
RISING EDGE
FALLING EDGE
LENGTH
EVENT
SIGNAL/SUPPLY
LENGTH
Enable/disable for BUCKx,
LDOx or GPOx
EN
3 µs(1)
3 µs(1)
VANA UVLO
VANA
VANA
3 µs(1) (VANA voltage rising)
Immediate (VANA voltage falling)
VANA overvoltage
Thermal warning
Thermal shutdown
Current limit
1 µs (VANA voltage rising)
20 µs (VANA voltage falling)
TDIE_WARN_INT
20 µs
20 µs
20 µs
20 µs
20 µs
20 µs
TDIE_SD_INT
VOUTx_ILIM
FB_B0, FB_B1,
VOUT_LDO0, VOUT_LDO1
Overload
1 ms
6 µs
N/V
PGOOD pin and power-good
interrupt
PGOOD / FB_B0, FB_B1,
VOUT_LDO0, VOUT_LDO1
6 µs
(1) No glitch filtering, only synchronization.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
33
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
7.4 Device Functional Modes
7.4.1 Modes of Operation
SHUTDOWN: The V(VANA) voltage is below VANAUVLO threshold level. All switch, reference, control, and bias
circuitry of the LP87332D-Q1 device are turned off.
READ OTP: The main supply voltage V(VANA) is above VANAUVLO level. The regulators are disabled, and
the reference and bias circuitry of the LP87332D-Q1 are enabled. The OTP bits are loaded to
registers.
STANDBY:
The main supply voltage V(VANA) is above VANAUVLO level. The regulators are disabled, and
the reference, control, and bias circuitry of the LP87332D-Q1 are enabled. All registers can be
read or written by the host processor through the system serial interface. The regulators can be
enabled if needed.
ACTIVE:
The main supply voltage V(VANA) is above VANAUVLO level. At least one regulator is enabled. All
registers can be read or written by the host processor through the system serial interface.
The operating modes and transitions between the modes are shown in 图 7-13.
SHUTDOWN
V(VANA) < VANAUVLO
V(VANA) > VANAUVLO
FROM ANY STATE
EXCEPT SHUTDOWN
READ
OTP
REG
RESET
STANDBY
I2C RESET
REGULATORS
ENABLED
REGULATORS
DISABLED
ACTIVE
图 7-13. Device Operation Modes
Copyright © 2021 Texas Instruments Incorporated
34
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
7.5 Programming
7.5.1 I2C-Compatible Interface
The I2C-compatible synchronous serial interface provides access to the programmable functions and registers
on the device. This protocol uses a two-wire interface for bidirectional communications between the ICs
connected to the bus. The two interface lines are the serial data line (SDA), and the serial clock line (SCL).
Every device on the bus is assigned a unique address, and acts as either a master or a slave depending on
whether it generates or receives the serial clock SCL. The SCL and SDA lines must each have a pullup resistor
placed on the line and remain HIGH even when the bus is idle. The LP87332D-Q1 supports standard mode (100
kHz), fast mode (400 kHz), fast mode plus (1 MHz), and high-speed mode (3.4 MHz).
7.5.1.1 Data Validity
The data on the SDA line must be stable during the HIGH period of the clock signal (SCL). In other words, the
state of the data line can only be changed when clock signal is LOW.
SCL
SDA
data
change
allowed
data
change
allowed
data
change
allowed
data
valid
data
valid
图 7-14. Data Validity Diagram
7.5.1.2 Start and Stop Conditions
The LP87332D-Q1 is controlled through an I2C-compatible interface. START and STOP conditions classify the
beginning and end of the I2C session. A START condition is defined as SDA transitions from HIGH to LOW while
SCL is HIGH. A STOP condition is defined as an SDA transition from LOW to HIGH while SCL is HIGH. The I2C
master always generates the START and STOP conditions.
SDA
SCL
S
P
START
STOP
Condition
Condition
图 7-15. Start and Stop Sequences
The I2C bus is considered busy after a START condition and free after a STOP condition. During data
transmission, the I2C master can generate repeated START conditions. A START and a repeated START
condition are equivalent function-wise. The data on SDA must be stable during the HIGH period of the clock
signal (SCL). In other words, the state of SDA can only be changed when SCL is LOW. 图 7-16 shows the SDA
and SCL signal timing for the I2C-compatible bus. See 节 6.6 for the timing values.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
35
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
tBUF
SDA
tHD;STA
trCL
tfDA
trDA
tSP
tLOW
tfCL
SCL
tHD;STA
tSU;STA
tSU;STO
tHIGH
tHD;DAT
S
tSU;DAT
S
RS
P
START
REPEATED
START
STOP
START
图 7-16. I2C-Compatible Timing
7.5.1.3 Transferring Data
Every byte put on the SDA line must be eight bits long, with the most significant bit (MSB) transferred first. Each
byte of data has to be followed by an acknowledge bit. The acknowledge-related clock pulse is generated by
the master. The master releases the SDA line (HIGH) during the acknowledge clock pulse. The LP87332D-Q1
pulls down the SDA line during the 9th clock pulse, signifying an acknowledge. The LP87332D-Q1 generates an
acknowledge after each byte has been received.
There is one exception to the acknowledge after every byte rule. When the master is the receiver, it must
indicate to the transmitter an end of data by not-acknowledging (negative acknowledge) the last byte clocked out
of the slave. This negative acknowledge still includes the acknowledge clock pulse (generated by the master),
but the SDA line is not pulled down.
Note
If the V(VANA) voltage is below the VANAUVLO threshold level during I2C communication, the
LP87332D-Q1 device does not drive SDA line. The ACK signal and data transfer to the master is
disabled at that time.
After the START condition, the bus master sends a chip address. This address is seven bits long, followed by
an eighth bit, which is a data direction bit (READ or WRITE). For the eighth bit, a 0 indicates a WRITE, and a 1
indicates a READ. The second byte selects the register to which the data will be written. The third byte contains
data to write to the selected register.
ACK from slave
ACK from slave
ACK from slave
START MSB Chip Address LSB
W
ACK MSB Register Address LSB ACK
MSB Data LSB
ACK STOP
SCL
SDA
START
id = 0x60
W
ACK
address = 0x40
ACK
address 0x40 data
ACK STOP
图 7-17. Write Cycle (w = write; SDA = 0). Example Device Address = 0x60
Copyright © 2021 Texas Instruments Incorporated
36
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
ACK from slave
ACK from slave REPEATED START
ACK from slave Data from slave NACK from master
START MSB Chip Address LSB
W
MSB Register Address LSB
RS
MSB Chip Address LSB
R
MSB Data LSB
STOP
SCL
SDA
START
ACK
ACK
ACK
NACK
STOP
id = 0x60
W
address = 0x3F
RS
id = 0x60
R
address 0x3F data
When READ function is to be accomplished, a WRITE function must precede the READ function as shown above.
图 7-18. Read Cycle (r = read; SDA = 1). Example Device Address = 0x60
7.5.1.4 I2C-Compatible Chip Address
Note
The device address for the LP87332D-Q1 is 0x60.
After the START condition, the I2C master sends the 7-bit address followed by an eighth bit, read or write (R/W).
R/W = 0 indicates a WRITE and R/W = 1 indicates a READ. The second byte following the device address
selects the register address to which the data is written. The third byte contains the data for the selected register.
MSB
LSB
1
Bit 7
1
Bit 6
0
Bit 5
0
Bit 4
0
Bit 3
0
Bit 2
0
Bit 1
R/W
Bit 0
I2C Slave Address (chip address)
Here in an example with device address of 1100000Bin = 60Hex.
图 7-19. Device Address Example
7.5.1.5 Auto-Increment Feature
The auto-increment feature allows writing several consecutive registers within one transmission. Every time an
8-bit word is sent to the LP87332D-Q1, the internal address index counter is incremented by one and the next
register is written. 表 7-6 shows writing sequence to two consecutive registers. The auto-increment feature does
not work for read.
表 7-6. Auto-Increment Example
DEVICE
START ADDRESS =
0x60
MASTER
ACTION
REGISTER
ADDRESS
WRITE
DATA
DATA
STOP
LP87332D-Q1
ACK
ACK
ACK
ACK
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
37
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
7.6 Register Maps
7.6.1 Register Descriptions
The LP87332D-Q1 is controlled by a set of registers through the I2C-compatible interface. The device registers
addresses and abbreviations are listed in 表 7-7. A more detailed description is given in the 节 7.6.1.1 to 节
7.6.1.39 sections.
The asterisk (*) marking indicates register bits which are updated from OTP memory during READ OTP state.
Note
This register map describes the default values for
a device with orderable code of
LP87332DRHDRQ1. For other device versions the default values read from OTP memory can be
different.
表 7-7. Summary of LP87332D-Q1 Control Registers
Addr
0x00
Register
Read / Write D7
D6
D5
D4
D3
D2
D1
D0
DEV_REV
OTP_REV
R
R
DEVICE_ID[1:0]
Reserved - do not use
0x01
0x02
OTP_ID[7:0]
BUCK0_
CTRL_1
R/W
Reserved - do not use
BUCK0_FP BUCK0_RDI
BUCK0_
EN_PIN_CT
RL
BUCK0_EN
WM S_EN
0x03
0x04
BUCK0_
CTRL_2
R/W
R/W
Reserved - do not use
Reserved - do not use
BUCK0_ILIM[2:0]
BUCK1_ILIM[2:0]
BUCK0_SLEW_RATE[2:0]
BUCK1_
CTRL_1
BUCK1_FP BUCK1_RDI
WM S_EN
BUCK1_
EN_PIN_CT
RL
BUCK1_EN
0x05
0x06
0x07
0x08
BUCK1_
CTRL_2
R/W
R/W
R/W
R/W
Reserved - do not use
BUCK1_SLEW_RATE[2:0]
BUCK0_
VOUT
BUCK0_VSET[7:0]
BUCK1_VSET[7:0]
BUCK1_
VOUT
LDO0_
CTRL
Reserved - do not use
LDO0_RDIS
LDO0_
EN_PIN_CT
RL
LDO0_EN
_EN
0x09
LDO1_
CTRL
R/W
Reserved - do not use
LDO1_RDIS
_EN
LDO1_
EN_PIN_CT
RL
LDO1_EN
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
0x11
0x12
LDO0_
VOUT
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reserved - do not use
LDO0_VSET[4:0]
LDO1_
VOUT
Reserved - do not use
LDO1_VSET[4:0]
BUCK0_
DELAY
BUCK0_SHUTDOWN_DELAY[3:0]
BUCK1_SHUTDOWN_DELAY[3:0]
LDO0_SHUTDOWN_DELAY[3:0]
LDO1_SHUTDOWN_DELAY[3:0]
GPO_SHUTDOWN_DELAY[3:0]
GPO2_SHUTDOWN_DELAY[3:0]
BUCK0_STARTUP_DELAY[3:0]
BUCK1_STARTUP_DELAY[3:0]
LDO0_STARTUP_DELAY[3:0]
LDO1_STARTUP_DELAY[3:0]
GPO_STARTUP_DELAY[3:0]
GPO2_STARTUP_DELAY[3:0]
BUCK1_
DELAY
LDO0_
DELAY
LDO1_
DELAY
GPO_
DELAY
GPO2_
DELAY
GPO_
CTRL
R/W
R/W
Reserved -
do not use
GPO2_OD
GPO2_
EN_PIN_CT
RL
GPO2_EN
Reserved -
do not use
GPO_OD
EN_PD
GPO_
EN_PIN_CT
RL
GPO_EN
0x13
CONFIG
Reserved - STARTUP_D SHUTDOW CLKIN_PIN_ CLKIN_PD
TDIE
EN_
do not use
ELAY_SEL N_DELAY_S
EL
SEL
_WARN
_LEVEL
SPREAD
_SPEC
Copyright © 2021 Texas Instruments Incorporated
38
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
表 7-7. Summary of LP87332D-Q1 Control Registers (continued)
Addr
0x14
Register
Read / Write D7
D6
D5
D4
D3
D2
D1
D0
PLL_CTRL
R/W
R/W
Reserved -
do not use
EN_PLL
Reserved -
EXT_CLK_FREQ[4:0]
do not use
PGOOD_PO PGOOD_OD PGOOD_WI PGOOD_WI EN_PGOOD EN_PGOOD EN_PGOOD EN_PGOOD
0x15
0x16
PGOOD_CT
RL_1
L
NDOW_LDO NDOW_BUC
K
_LDO1
_LDO0
_BUCK1
_BUCK0
PGOOD_CT
RL_2
R/W
Reserved - do not use
EN_PGOOD PG_FAULT_ PGOOD_M
_TWARN
GATES_PG
OOD
ODE
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
PG_FAULT
RESET
R
Reserved - do not use
PG_FAULT_ PG_FAULT_ PG_FAULT_ PG_FAULT_
LDO1
LDO0
BUCK1
BUCK0
R/W
R/W
R/W
R/W
R/W
R
Reserved - do not use
SW_
RESET
INT_TOP_1
INT_TOP_2
INT_BUCK
INT_LDO
PGOOD_
INT
INT_
LDO
INT_
BUCK
SYNC_
CLK_INT
TDIE_SD_IN
T
TDIE_
WARN_INT
OVP_INT
I_MEAS_
INT
Reserved - do not use
RESET_
REG_INT
Reserved -
do not use
BUCK1_
PG_INT
BUCK1_
SC_INT
BUCK1_
ILIM_INT
Reserved -
do not use
BUCK0_
PG_INT
BUCK0_
SC_INT
BUCK0_
ILIM_INT
Reserved -
do not use
LDO1_
LDO1_
LDO1_
ILIM_INT
Reserved -
do not use
LDO0_
PG_INT
LDO0_
SC_INT
LDO0_
ILIM_INT
PG_INT
SC_INT
TOP_
STAT
PGOOD_ST
AT
Reserved - do not use
SYNC_CLK
_STAT
TDIE_SD
_STAT
TDIE_
WARN_
STAT
OVP_
STAT
Reserved -
do not use
0x1E
0x1F
0x20
0x21
0x22
BUCK_STAT
LDO_STAT
R
BUCK1_
STAT
BUCK1_
PG_STAT
Reserved -
do not use
BUCK1_
ILIM_STAT
BUCK0_
STAT
BUCK0_
PG_STAT
Reserved -
do not use
BUCK0_
ILIM_STAT
R
LDO1_
STAT
LDO1_
PG_STAT
Reserved -
do not use
LDO1_
ILIM_STAT
LDO0_
STAT
LDO0_
PG_STAT
Reserved -
do not use
LDO0_
ILIM_STAT
TOP_
MASK_1
R/W
R/W
R/W
PGOOD_
INT_MASK
Reserved - do not use
SYNC_CLK Reserved - TDIE_WARN Reserved -
_MASK do not use _MASK do not use
I_MEAS_
MASK
TOP_
MASK_2
Reserved - do not use
RESET_
REG_MASK
BUCK_MAS
K
BUCK1_PG BUCK1_PG Reserved -
F_MASK R_MASK do not use
BUCK1_
ILIM_
BUCK0_PG BUCK0_PG Reserved -
F_MASK R_MASK do not use
BUCK0_
ILIM_
MASK
MASK
0x23
0x24
LDO_MASK
R/W
R/W
LDO1_PGF_ LDO1_PGR Reserved -
MASK _MASK do not use
LDO1_
ILIM_
MASK
LDO0_PGF_ LDO0_PGR Reserved -
MASK _MASK do not use
LDO0_
ILIM_
MASK
SEL_I_
LOAD
Reserved - do not use
LOAD_CUR
RENT_
BUCK_SEL
ECT
0x25
0x26
I_LOAD_2
I_LOAD_1
R
R
Reserved - do not use
BUCK_LOA
D_CURREN
T[8]
BUCK_LOAD_CURRENT[7:0]
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
39
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
7.6.1.1 DEV_REV
DEV_REV is shown in 表 7-9, Address: 0x00
表 7-8. DEV_REV Register
D7
D6
D5
D4
D3
D2
D1
D0
DEVICE_ID[1:0]
Reserved - do not use
表 7-9. DEV_REV Register Field Descriptions
Bits
7:6
Field
Type
R
Default
Description
DEVICE_ID[1:0]
0x0
Device specific ID code.
5:0
Reserved - do not
use
R
00 0010
7.6.1.2 OTP_REV
OTP_REV is shown in 表 7-11, Address: 0x01
表 7-10. OTP_REV Register
D7
D6
D5
D4
D3
D2
D1
D0
OTP_ID[7:0]
表 7-11. OTP_REV Register Field Descriptions
Bits
Field
Type
Default
Description
7:0
OTP_ID[7:0]
R
0x2D
Identification Code of the OTP EPROM Version.
7.6.1.3 BUCK0_CTRL_1
BUCK0_CTRL_1 is shown in the 表 7-13, Address: 0x02
表 7-12. BUCK0_CTRL_1 Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do not use
BUCK0_FPWM BUCK0_RDIS_ BUCK0_EN_PI
EN N_CTRL
BUCK0_EN
表 7-13. BUCK0_CTRL_1 Register Field Descriptions
Bits
Field
Type
Default
Description
7:4
Reserved - do not
use
R/W
0000
3
2
1
0
BUCK0_FPWM
R/W
R/W
R/W
R/W
0
1
1
1
Buck0 mode selection:
0 - Automatic transitions between the PFM and PWM modes (AUTO mode).
1 - Forced to PWM operation.
BUCK0_RDIS_EN
Enable output discharge resistor (RDIS_Bx) when the Buck0 is disabled:
0 - Discharge resistor disabled.
1 - Discharge resistor enabled.
BUCK0_EN_PIN
_CTRL
Enable control for the Buck0:
0 - only the BUCK0_EN bit controls the Buck0.
1 - BUCK0_EN bit and the EN pin control the Buck0.
BUCK0_EN
Enable the Buck0 regulator:
0 - Buck0 regulator is disabled.
1 - Buck0 regulator is enabled.
7.6.1.4 BUCK0_CTRL_2
BUCK0_CTRL_2 is shown in 表 7-15, Address: 0x03
Copyright © 2021 Texas Instruments Incorporated
40
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
表 7-14. BUCK0_CTRL_2 Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do not use
BUCK0_ILIM[2:0]
BUCK0_SLEW_RATE[2:0]
表 7-15. BUCK0_CTRL_2 Register Field Descriptions
Bits
Field
Type
Default
Description
7:6
Reserved - do not
use
R/W
00
5:3
BUCK0_ILIM[2:0]
R/W
0x5
Sets the switch current limit of Buck0. Can be programmed at any time during
operation:
0x0 - 1.5 A
0x1 - 2.0 A
0x2 - 2.5 A
0x3 - 3.0 A
0x4 - 3.5 A
0x5 - 4.0 A
0x6 - Reserved - do not use.
0x7 - Reserved - do not use.
2:0 BUCK0_SLEW_RA
TE[2:0]
R/W
0x2
Sets the output voltage slew rate for Buck0 regulator (rising and falling edges):
0x0 - Reserved - do not use.
0x1 - Reserved - do not use.
0x2 - 10 mV/µs
0x3 - 7.5 mV/µs
0x4 - 3.8 mV/µs
0x5 - 1.9 mV/µs
0x6 - 0.94 mV/µs
0x7 - 0.47 mV/µs
7.6.1.5 BUCK1_CTRL_1
BUCK1_CTRL_1 is shown in 表 7-17, Address: 0x04
表 7-16. BUCK1_CTRL_1 Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do not use
BUCK1_FPWM BUCK1_RDIS_ BUCK1_EN_PI
EN N_CTRL
BUCK1_EN
表 7-17. BUCK1_CTRL_1 Register Field Descriptions
Bits
Field
Type
Default
Description
7:4
Reserved - do not
use
R/W
0000
3
2
1
0
BUCK1_FPWM
R/W
R/W
R/W
R/W
0
1
1
1
Buck1 mode selection:
0 - Automatic transitions between the PFM and PWM modes (AUTO mode).
1 - Forced to PWM operation.
BUCK1_RDIS_EN
Enable output discharge resistor (RDIS_Bx) when the Buck1 is disabled:
0 - Discharge resistor is disabled.
1 - Discharge resistor is enabled.
BUCK1_EN_PIN
_CTRL
Enable control for the Buck1:
0 - only the BUCK1_EN bit controls the Buck1
1 - BUCK1_EN bit and the EN pin control the Buck1.
BUCK1_EN
Enable the Buck1 regulator:
0 - Buck1 regulator is disabled.
1 - Buck1 regulator is enabled.
7.6.1.6 BUCK1_CTRL_2
BUCK1_CTRL_2 is shown in 表 7-19, Address: 0x05
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
41
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
表 7-18. BUCK1_CTRL_2 Register
D7
D6
D5
D4
D3
D2
D1
BUCK1_SLEW_RATE[2:0]
D0
Reserved - do not use
BUCK1_ILIM[2:0]
表 7-19. BUCK1_CTRL_2 Register Field Descriptions
Bits
Field
Type
Default
Description
7:6
Reserved - do not
use
R/W
00
5:3
BUCK1_ILIM[2:0]
R/W
0x5
Sets the switch current limit of the Buck1. Can be programmed at any time during
operation:
0x0 - 1.5 A
0x1 - 2.0 A
0x2 - 2.5 A
0x3 - 3.0 A
0x4 - 3.5 A
0x5 - 4.0 A
0x6 - Reserved - do not use.
0x7 - Reserved - do not use.
2:0 BUCK1_SLEW_RA
TE[2:0]
R/W
0x2
Sets the output voltage slew rate for the Buck1 regulator (rising and falling edges):
0x0 - Reserved - do not use.
0x1 - Reserved - do not use.
0x2 - 10 mV/µs
0x3 - 7.5 mV/µs
0x4 - 3.8 mV/µs
0x5 - 1.9 mV/µs
0x6 - 0.94 mV/µs
0x7 - 0.47 mV/µs
7.6.1.7 BUCK0_VOUT
BUCK0_VOUT is shown in 表 7-21, Address: 0x06
表 7-20. BUCK0_VOUT Register
D7
D6
D5
D4
D3
D2
D1
D0
BUCK0_VSET[7:0]
表 7-21. BUCK0_VOUT Register Field Descriptions
Bits
Field
Type
Default
Description
7:0 BUCK0_VSET[7:0]
R/W
0x6B
Sets the output voltage of the Buck0 regulator:
Reserved; do not use.
0x00 ... 0x13
0.7 V - 0.73 V, 10 mV steps
0x14 - 0.7V
...
0x17 - 0.73 V
0.73 V - 1.4 V, 5 mV steps
0x18 - 0.735 V
...
0x9D - 1.4 V
1.4 V - 3.36 V, 20 mV steps
0x9E - 1.42 V
...
0xFF - 3.36 V
7.6.1.8 BUCK1_VOUT
BUCK1_VOUT is shown in 表 7-23, Address: 0x07
表 7-22. BUCK1_VOUT Register
D7
D6
D5
D4
D3
D2
D1
D0
Copyright © 2021 Texas Instruments Incorporated
42
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
BUCK1_VSET[7:0]
表 7-23. BUCK1_VOUT Register Field Descriptions
Bits
Field
Type
Default
Description
7:0 BUCK1_VSET[7:0]
R/W
0x59
Sets the output voltage of the Buck0 regulator:
Reserved; do not use.
0x00 ... 0x13
0.7 V - 0.73 V, 10 mV steps
0x14 - 0.7V
...
0x17 - 0.73 V
0.73 V - 1.4 V, 5 mV steps
0x18 - 0.735 V
...
0x9D - 1.4 V
1.4 V - 3.36 V, 20 mV steps
0x9E - 1.42 V
...
0xFF - 3.36 V
7.6.1.9 LDO0_CTRL
LDO0_CTRL is shown in 表 7-25, Address: 0x08
表 7-24. LDO0_CTRL Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do not use
LDO0_RDIS_E LDO0_EN_PIN
_CTRL
LDO0_EN
N
表 7-25. LDO0_CTRL Register Field Descriptions
Bits
Field
Type
Default
Description
7:3
Reserved - do not
use
R/W
0 0000
2
1
0
LDO0_RDIS_EN
R/W
R/W
R/W
1
1
1
Enable output discharge resistor (RDIS_LDOx) when the LDO0 is disabled:
0 - Discharge resistor is disabled.
1 - Discharge resistor is enabled.
LDO0_EN_PIN
_CTRL
Enable control for the LDO0:
0 - only the LDO0_EN bit controls the LDO0.
1 - LDO0_EN bit and the EN pin control the LDO0.
LDO0_EN
Enable the LDO0 regulator:
0 - LDO0 regulator is disabled.
1 - LDO0 regulator is enabled.
7.6.1.10 LDO1_CTRL
LDO1_CTRL is shown in 表 7-27, Address: 0x09
表 7-26. LDO1_CTRL Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do not use
LDO1_RDIS_E LDO1_EN_PIN
_CTRL
LDO1_EN
N
表 7-27. LDO1_CTRL Register Field Descriptions
Bits
Field
Type
Default
Description
7:3
Reserved - do not
use
R/W
0 0000
2
LDO1_RDIS_EN
R/W
1
Enable output discharge resistor (RDIS_LDOx) when the LDO1 is disabled:
0 - Discharge resistor is disabled.
1 - Discharge resistor is enabled.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
43
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
表 7-27. LDO1_CTRL Register Field Descriptions (continued)
Bits
Field
Type
Default
Description
1
LDO1_EN_PIN
_CTRL
R/W
1
Enable control for the LDO1:
0 - only the LDO1_EN bit controls the LDO1.
1 - LDO1_EN bit and the EN pin control the LDO1.
0
LDO1_EN
R/W
1
Enable the LDO1 regulator:
0 - LDO1 regulator is disabled.
1 - LDO1 regulator is enabled.
7.6.1.11 LDO0_VOUT
LDO0_VOUT is shown in 表 7-29, Address: 0x0A
表 7-28. LDO0_VOUT Register
D7
D6
D5
D4
D3
D2
D1
D1
D1
D0
Reserved - do not use
LDO0_VSET[4:0]
表 7-29. LDO0_VOUT Register Field Descriptions
Bits
Field
Type
Default
Description
7:5
Reserved - do not
use
R/W
000
4:0
LDO0_VSET[4:0]
R/W
0x19
Sets the output voltage of the LDO0 regulator:
0.8 V - 3.3 V, 100 mV steps
0x00 - 0.8V
...
0x19 - 3.3 V
Reserved; do not use.
0x1A ... 0x1F
7.6.1.12 LDO1_VOUT
LDO1_VOUT is shown in 表 7-31, Address: 0x0B
表 7-30. LDO1_VOUT Register
D7
D6
D5
D4
D3
D2
D0
Reserved - do not use
LDO1_VSET[4:0]
表 7-31. LDO1_VOUT Register Field Descriptions
Bits
Field
Type
Default
Description
7:5
Reserved - do not
use
R/W
000
4:0
LDO1_VSET[4:0]
R/W
0x19
Sets the output voltage of the LDO1 regulator:
0.8 V - 3.3 V, 100 mV steps
0x00 - 0.8V
...
0x19 - 3.3 V
Reserved; do not use.
0x1A ... 0x1F
7.6.1.13 BUCK0_DELAY
BUCK0_DELAY is shown in 表 7-33, Address: 0x0C
表 7-32. BUCK0_DELAY Register
D7
D6
D5
D4
D3
D2
D0
BUCK0_SHUTDOWN_DELAY[3:0]
BUCK0_STARTUP_DELAY[3:0]
Copyright © 2021 Texas Instruments Incorporated
44
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
www.ti.com.cn
Bits
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
表 7-33. BUCK0_DELAY Register Field Descriptions
Field
Type
Default
Description
7:4
BUCK0_
SHUTDOWN_
DELAY[3:0]
R/W
0x2
Shutdown delay of the Buck0 from the EN signal's falling edge:
0x0 - 0 ms
0x1 - 0.5 ms (1 ms if SHUTDOWN_DELAY_SEL=1 in the CONFIG register.)
...
0xF - 7.5 ms (15 ms if SHUTDOWN_DELAY_SEL=1 in the CONFIG register.)
3:0
BUCK0_
STARTUP_
DELAY[3:0]
R/W
0x3
Startup delay of the Buck0 from the EN signal's rising edge:
0x0 - 0 ms
0x1 - 0.5 ms (1 ms if STARTUP_DELAY_SEL=1 in the CONFIG register.)
...
0xF - 7.5 ms (15 ms if STARTUP_DELAY_SEL=1 in the CONFIG register.)
7.6.1.14 BUCK1_DELAY
BUCK1_DELAY is shown in 表 7-35, Address: 0x0D
表 7-34. BUCK1_DELAY Register
D7
D6
D5
D4
D3
D2
D1
D0
BUCK1_SHUTDOWN_DELAY[3:0]
BUCK1_STARTUP_DELAY[3:0]
表 7-35. BUCK1_DELAY Register Field Descriptions
Bits
Field
Type
Default
Description
7:4
BUCK1_
SHUTDOWN_
DELAY[3:0]
R/W
0x2
Shutdown delay of the Buck1 from the EN signal's falling edge:
0x0 - 0 ms
0x1 - 0.5 ms (1 ms if SHUTDOWN_DELAY_SEL=1 in the CONFIG register.)
...
0xF - 7.5 ms (15 ms if SHUTDOWN_DELAY_SEL=1 in the CONFIG register.)
3:0
BUCK1_
STARTUP_
DELAY[3:0]
R/W
0x4
Startup delay of the Buck1 from the EN signal's rising edge:
0x0 - 0 ms
0x1 - 0.5 ms (1 ms if STARTUP_DELAY_SEL=1 in the CONFIG register.)
...
0xF - 7.5 ms (15 ms if STARTUP_DELAY_SEL=1 in the CONFIG register.)
7.6.1.15 LDO0_DELAY
LDO0_DELAY is shown in 表 7-37, Address: 0x0E
表 7-36. LDO0_DELAY Register
D7
D6
D5
D4
D3
D2
D1
D0
LDO0_SHUTDOWN_DELAY[3:0]
LDO0_STARTUP_DELAY[3:0]
表 7-37. LDO0_DELAY Register Field Descriptions
Bits
Field
Type
Default
Description
7:4
LDO0_
R/W
0x0
Shutdown delay of the LDO0 from the EN signal's falling edge:
SHUTDOWN_
DELAY[3:0]
0x0 - 0 ms
0x1 - 0.5 ms (1 ms if SHUTDOWN_DELAY_SEL=1 in the CONFIG register.)
...
0xF - 7.5 ms (15 ms if SHUTDOWN_DELAY_SEL=1 in the CONFIG register.)
3:0
LDO0_
R/W
0x7
Startup delay of the LDO0 from the EN signal's rising edge:
STARTUP_
DELAY[3:0]
0x0 - 0 ms
0x1 - 0.5 ms (1 ms if STARTUP_DELAY_SEL=1 in the CONFIG register.)
...
0xF - 7.5 ms (15 ms if STARTUP_DELAY_SEL=1 in the CONFIG register.)
7.6.1.16 LDO1_DELAY
LDO1_DELAY is shown in 表 7-39, Address: 0x0F
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
45
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
表 7-38. LDO1_DELAY Register
D7
D6
D5
D4
D3
D2
D1
D0
LDO1_SHUTDOWN_DELAY[3:0]
LDO1_STARTUP_DELAY[3:0]
表 7-39. LDO1_DELAY Register Field Descriptions
Bits
Field
Type
Default
Description
7:4
LDO1_
SHUTDOWN_
DELAY[3:0]
R/W
0x2
Shutdown delay of the LDO1 from the EN signal's falling edge:
0x0 - 0 ms
0x1 - 0.5 ms (1 ms if SHUTDOWN_DELAY_SEL=1 in the CONFIG register.)
...
0xF - 7.5 ms (15 ms if SHUTDOWN_DELAY_SEL=1 in the CONFIG register.)
3:0
LDO1_
R/W
0x5
Startup delay of the LDO1 from the EN signal's rising edge:
STARTUP_
DELAY[3:0]
0x0 - 0 ms
0x1 - 0.5 ms (1 ms if STARTUP_DELAY_SEL=1 in the CONFIG register.)
...
0xF - 7.5 ms (15 ms if STARTUP_DELAY_SEL=1 in the CONFIG register.)
7.6.1.17 GPO_DELAY
GPO_DELAY is shown in 表 7-41, Address: 0x10
表 7-40. GPO_DELAY Register
D7
D6
D5
D4
D3
D2
D1
D0
GPO_SHUTDOWN_DELAY[3:0]
GPO_STARTUP_DELAY[3:0]
表 7-41. GPO_DELAY Register Field Descriptions
Bits
Field
Type
Default
Description
7:4
GPO_
R/W
0x0
Delay for the GPO falling edge from the EN signal's falling edge:
SHUTDOWN_
DELAY[3:0]
0x0 - 0 ms
0x1 - 0.5 ms (1 ms if SHUTDOWN_DELAY_SEL=1 in the CONFIG register)
...
0xF - 7.5 ms (15 ms if SHUTDOWN_DELAY_SEL=1 in the CONFIG register)
3:0
GPO_
R/W
0x7
Delay for the GPO rising edge from the EN signal's rising edge:
STARTUP_
DELAY[3:0]
0x0 - 0 ms
0x1 - 0.5 ms (1 ms if STARTUP_DELAY_SEL=1 in the CONFIG register.)
...
0xF - 7.5 ms (15 ms if STARTUP_DELAY_SEL=1 in the CONFIG register.)
7.6.1.18 GPO2_DELAY
GPO2_DELAY is shown in 表 7-43, Address: 0x11
表 7-42. GPO2_DELAY Register
D7
D6
D5
D4
D3
D2
D1
D0
GPO2_SHUTDOWN_DELAY[3:0]
GPO2_STARTUP_DELAY[3:0]
表 7-43. GPO2_DELAY Register Field Descriptions
Bits
Field
Type
Default
Description
7:4
GPO2_
R/W
0x0
Delay for the GPO2 falling edge from the EN signal's falling edge:
SHUTDOWN_
DELAY[3:0]
0x0 - 0 ms
0x1 - 0.5 ms (1 ms if SHUTDOWN_DELAY_SEL=1 in the CONFIG register.)
...
0xF - 7.5 ms (15 ms if SHUTDOWN_DELAY_SEL=1 in the CONFIG register.)
Copyright © 2021 Texas Instruments Incorporated
46
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
www.ti.com.cn
Bits
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
表 7-43. GPO2_DELAY Register Field Descriptions (continued)
Field
Type
Default
Description
3:0
GPO2_
R/W
0xA
Delay for the GPO2 rising edge from the EN signal's rising edge:
STARTUP_
DELAY[3:0]
0x0 - 0 ms
0x1 - 0.5 ms (1 ms if STARTUP_DELAY_SEL=1 in the CONFIG register.)
...
0xF - 7.5 ms (15 ms if STARTUP_DELAY_SEL=1 in the CONFIG register.)
7.6.1.19 GPO_CTRL
GPO_CTRL is shown in 表 7-45, Address: 0x12
表 7-44. GPO_CTRL Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do
not use
GPO2_OD
GPO2_EN_PIN
_CTRL
GPO2_EN
Reserved - do
not use
GPO_OD
GPO_EN_PIN_
CTRL
GPO_EN
表 7-45. GPO_CTRL Register Field Descriptions
Bits
Field
Reserved - do not
Type
Default
Description
7
R
0
use
6
5
4
GP02_OD
R/W
R/W
R/W
1
1
1
GPO2 signal type when configured as the General Purpose Output (CLKIN pin):
0 - Push-pull output (VANA level)
1 - Open-drain output
GPO2_EN_PIN_CT
RL
Control for the GPO2:
0 - Only the GPO2_EN bit controls the GPO2
1 - GPO2_EN bit and the EN pin control the GPO2.
GPO2_EN
Output level of the GPO2 signal (when configured as the General Purpose Output):
0 - Logic low level
1 - Logic high level
3
2
Reserved - do not
use
R
0
1
GPO_OD
R/W
GPO signal type:
0 - Push-pull output (VANA level)
1 - Open-drain output
1
0
GPO_EN_PIN_CTR
L
R/W
R/W
1
1
Control for the GPO:
0 - Only the GPO_EN bit controls the GPO
1 - GPO_EN bit and the EN pin control the GPO.
GPO_EN
Output level of the GPO signal:
0 - Logic low level
1 - Logic high level
7.6.1.20 CONFIG
CONFIG is shown in 表 7-47, Address: 0x13
表 7-46. CONFIG Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do STARTUP_DEL SHUTDOWN_D CLKIN_PIN_SE
not use AY_SEL ELAY_SEL
CLKIN_PD
EN2_PD
TDIE_WARN_
LEVEL
EN_SPREAD
_SPEC
L
表 7-47. CONFIG Register Field Descriptions
Bits
Field
Type
Default
Description
7
Reserved - do not
use
R/W
0
6
STARTUP_DELAY_
SEL
R/W
0
Startup delay range from the EN signals:
0 - 0 ms - 7.5 ms with 0.5 ms steps
1 - 0 ms - 15 ms with 1 ms steps
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
47
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
表 7-47. CONFIG Register Field Descriptions (continued)
Bits
Field
Type
Default
Description
5
SHUTDOWN_DELA
Y_SEL
R/W
0
Shutdown delay range from the EN signals:
0 - 0 ms - 7.5 ms with 0.5 ms steps
1 - 0 ms - 15 ms with 1 ms steps
4
3
CLKIN_PIN_SEL
CLKIN_PD
R/W
R/W
0
0
CLKIN pin function:
0 - GPO2
1 - CLKIN
Selects the pull down resistor on the CLKIN input pin (valid also when selected as
GPO2):
0 - Pull-down resistor is disabled.
1 - Pull-down resistor is enabled.
2
1
0
EN_PD
R/W
R/W
R/W
1
1
0
Selects the pull down resistor on the EN input pin.
0 - Pull-down resistor is disabled.
1 - Pull-down resistor is enabled.
TDIE_WARN_
LEVEL
Thermal warning threshold level:
0 - 125°C
1 - 137°C
EN_SPREAD
_SPEC
Enable spread spectrum feature:
0 - Disabled
1 - Enabled
7.6.1.21 PLL_CTRL
PLL_CTRL is shown in 表 7-49, Address: 0x14
表 7-48. PLL_CTRL Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do
not use
EN_PLL
Reserved - do
not use
EXT_CLK_FREQ[4:0]
表 7-49. PLL_CTRL Register Field Descriptions
Bits
Field
Reserved - do not
Type
Default
Description
7
R/W
0
use
6
EN_PLL
R/W
0
Selection of the external clock and PLL operation:
0 - Forced to the internal RC oscillator. The PLL is disabled.
1 - PLL is enabled in the STANDBY and ACTIVE modes. Automatic external clock
use when available, and interrupt is generated if the external clock appears or
disappears.
5
Reserved - do not
use
R/W
R/W
0
This bit must be set to '''0 .''
4:0 EXT_CLK_FREQ[4:
0]
0x1
Frequency of the external clock (CLKIN):
0x00 - 1 MHz
0x01 - 2 MHz
0x02 - 3 MHz
...
0x16 - 23 MHz
0x17 - 24 MHz
0x18...0x1F - Reserved - do not use
See electrical specification for the input clock frequency tolerance.
7.6.1.22 PGOOD_CTRL_1
PGOOD_CTRL_1 is shown in 表 7-51, Address: 0x15
表 7-50. PGOOD_CTRL_1 Register
D7
D6
D5
D4
D3
D2
D1
D0
Copyright © 2021 Texas Instruments Incorporated
48
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
PGOOD_POL
PGOOD_OD
PGOOD_
PGOOD_
EN_PGOOD_L EN_PGOOD_L EN_PGOOD_B EN_PGOOD_B
WINDOW_LDO WINDOW_BUC
K
DO1
DO0
UCK1
UCK0
表 7-51. PGOOD_CTRL_1 Register Field Descriptions
Bits
Field
Type
Default
Description
7
PGOOD_POL
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
PGOOD signal polarity:
0 - PGOOD signal high when the monitored outputs are valid.
1 - PGOOD signal low when the monitored outputs are valid.
6
5
4
3
2
1
0
PGOOD_OD
1
1
1
0
0
1
1
PGOOD signal type:
0 - Push-pull output (VANA level)
1 - Open-drain output
PGOOD_
WINDOW_LDO
LDO Output voltage monitoring method for the PGOOD signal:
0 - Only undervoltage monitoring
1 - Overvoltage and undervoltage monitoring
PGOOD_
WINDOW_BUCK
Buck Output voltage monitoring method for the PGOOD signal:
0 - Only undervoltage monitoring
1 - Overvoltage and undervoltage monitoring
EN_PGOOD_LDO1
EN_PGOOD_LDO0
PGOOD signal source control from LDO1:
0 - LDO1 is not monitored.
1 - LDO1 Power-Good threshold voltage is monitored.
PGOOD signal source control from theLDO0:
0 - LDO0 is not monitored.
1 - LDO0 Power-Good threshold voltage is monitored.
EN_PGOOD_BUCK
1
PGOOD signal source control from the Buck1:
0 - Buck1 is not monitored.
1 - Buck1 Power-Good threshold voltage is monitored.
EN_PGOOD_BUCK
0
PGOOD signal source control from the Buck0:
0 - Buck0 is not monitored.
1 - Buck0 Power-Good threshold voltage is monitored.
7.6.1.23 PGOOD_CTRL_2
PGOOD_CTRL_2 is shown in 表 7-53, Address: 0x16
表 7-52. PGOOD_CTRL_2 Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do not use
EN_PGOOD_T PG_FAULT_GA PGOOD_MOD
WARN
TES_PGOOD
E
表 7-53. PGOOD_CTRL_2 Register Field Descriptions
Bits
Field
Type
Default
Description
7:3
Reserved - do not
use
R/W
0 0000
2
1
EN_PGOOD_TWA
RN
R/W
R/W
1
0
Thermal warning control for the PGOOD signal:
0 - Thermal warning is not monitored.
1 - PGOOD inactive if the thermal warning flag is active.
PG_FAULT_GATES
_PGOOD
Type of operation for the PGOOD signal:
0 - Indicates live status of monitored voltage outputs.
1 - Indicates status of the PG_FAULT register, inactive when at least one
PG_FAULT_x bit is inactive.
0
PGOOD_MODE
R/W
0
Operating mode for the PGOOD signal:
0 - Gated mode
1 - Continuous mode
7.6.1.24 PG_FAULT
PG_FAULT is shown in 表 7-55, Address: 0x17
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
49
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
表 7-54. PG_FAULT Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do not use
PG_FAULT_LD PG_FAULT_LD PG_FAULT_BU PG_FAULT_BU
O1 O0 CK1 CK0
表 7-55. PG_FAULT Register Field Descriptions
Bits
Field
Type
Default
Description
7:4
Reserved - do not
use
R/W
0000
3
2
1
0
PG_FAULT_LDO1
PG_FAULT_LDO0
PG_FAULT_BUCK1
PG_FAULT_BUCK0
R/W
R/W
R/W
R/W
0
0
0
0
Source for the PGOOD inactive signal:
0 - LDO1 has not set the PGOOD signal inactive.
1 - LDO1 is selected for the PGOOD signal and it has set the PGOOD signal inactive.
This bit can be cleared by writing '1' to this bit when the LDO1 output is valid.
Source for PGOOD inactive signal:
0 - LDO0 has not set the PGOOD signal inactive.
1 - LDO0 is selected for the PGOOD signal and it has set the PGOOD signal inactive.
This bit can be cleared by writing '1' to this bit when the LDO0 output is valid.
Source for PGOOD inactive signal:
0 - Buck1 has not set PGOOD signal inactive.
1 - Buck1 is selected for the PGOOD signal and it has set the PGOOD signal inactive.
This bit can be cleared by writing '1' to this bit when the Buck1 output is valid.
Source for PGOOD inactive signal:
0 - Buck0 has not set PGOOD signal inactive.
1 - Buck0 is selected for the PGOOD signal and it has set the PGOOD signal inactive.
This bit can be cleared by writing '1' to this bit when the Buck0 output is valid.
7.6.1.25 RESET
RESET is shown in 表 7-57, Address: 0x18
表 7-56. RESET Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do not use
SW_RESET
表 7-57. RESET Register Field Descriptions
Bits
Field
Type
Default
Description
7:1
Reserved - do not
use
R/W
000 0000
0
SW_RESET
R/W
0
Software commanded reset. When written to 1, the registers will be reset to the
default values, the OTP memory is read, and the I2C interface is reset.
The bit is automatically cleared.
7.6.1.26 INT_TOP_1
INT_TOP_1 is shown in 表 7-59, Address: 0x19
表 7-58. INT_TOP_1 Register
D7
D6
D5
D4
D3
D2
D1
D0
PGOOD_INT
LDO_INT
BUCK_INT
SYNC_CLK_IN TDIE_SD_INT TDIE_WARN_I
NT
OVP_INT
I_MEAS_INT
T
表 7-59. INT_TOP_1 Register Field Descriptions
Bits
Field
PGOOD_INT
Type
Default
Description
7
R/W
0
Latched status bit indicating that the PGOOD pin has changed from active to inactive.
Write 1 to clear interrupt.
Copyright © 2021 Texas Instruments Incorporated
50
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
www.ti.com.cn
Bits
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
表 7-59. INT_TOP_1 Register Field Descriptions (continued)
Field
Type
Default
Description
6
LDO_INT
R
0
Interrupt indicating that the LDO1 and LDO0 have a pending interrupt. The reason for
the interrupt is indicated in the INT_LDO register.
This bit is cleared automatically when the INT_LDO register is cleared to 0x00.
5
BUCK_INT
R
0
Interrupt indicating that the Buck1 and Buck0 have a pending interrupt. The reason
for the interrupt is indicated in the INT_BUCK register.
This bit is cleared automatically when INT_BUCK register is cleared to 0x00.
4
3
SYNC_CLK_INT
TDIE_SD_INT
R/W
R/W
0
0
Latched status bit indicating that the external clock has appeared or disappeared.
Write 1 to clear interrupt.
Latched status bit indicating that the die junction temperature has exceeded the
thermal shutdown level. The regulators have been disabled if they were enabled
and the GPO and GPO2 signals are driven low. The regulators cannot be enabled
if this bit is active. The actual status of the thermal shutdown is indicated by the
TDIE_SD_STAT bit in the TOP_STAT register.
Write 1 to clear interrupt.
2
1
TDIE_WARN_INT
OVP_INT
R/W
R/W
0
0
Latched status bit indicating that the die junction temperature has exceeded the
thermal warning level. The actual status of the thermal warning is indicated by the
TDIE_WARN_STAT bit in the TOP_STAT register.
Write 1 to clear interrupt.
Latched status bit indicating that the input voltage has exceeded the over-voltage
detection level. The regulators have been disabled if they were enabled and the GPO
and GPO2 signals are driven low. The actual status of the over-voltage is indicated by
the OVP_STAT bit in the TOP_STAT register.
Write 1 to clear interrupt.
0
I_MEAS_INT
R/W
0
Latched status bit indicating that the load current measurement result is available in
the I_LOAD_1 and I_LOAD_2 registers.
Write 1 to clear interrupt.
7.6.1.27 INT_TOP_2
INT_TOP_2 is shown in 表 7-61, Address: 0x1A
表 7-60. INT_TOP_2 Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do not use
RESET_REG_I
NT
表 7-61. INT_TOP_2 Register Field Descriptions
Bits
Field
Type
Default
Description
7:1
Reserved - do not
use
R/W
000 0000
0
RESET_REG_INT
R/W
0
Latched status bit indicating that either VANA supply voltage has been below the
undervoltage threshold level or the host has requested a reset using the SW_RESET
bit in RESET register. The regulators have been disabled, the registers are reset to
the default values, and the normal startup procedure is done.
Write 1 to clear interrupt.
7.6.1.28 INT_BUCK
INT_BUCK is shown in 表 7-63, Address: 0x1B
表 7-62. INT_BUCK Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do
not use
BUCK1_PG
_INT
BUCK1_SC
_INT
BUCK1_ILIM
_INT
Reserved - do
not use
BUCK0_PG
_INT
BUCK0_SC
_INT
BUCK0_ILIM
_INT
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
51
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
表 7-63. INT_BUCK Register Field Descriptions
Bits
Field
Type
Default
Description
7
Reserved - do not
use
R/W
0
6
5
BUCK1_PG_INT
R/W
R/W
0
0
Latched status bit indicating that Buck1 Power-Good event has been detected.
Write 1 to clear.
BUCK1_SC_INT
Latched status bit indicating that the Buck1 output voltage has been over 1 ms below
the short-circuit threshold level.
Write 1 to clear.
4
3
2
1
BUCK1_ILIM_INT
R/W
R/W
R/W
R/W
0
0
0
0
Latched status bit indicating that the Buck1 output current limit has been active.
Write 1 to clear.
Reserved - do not
use
BUCK0_PG_INT
Latched status bit indicating that the Buck0 Power-Good event has been detected.
Write 1 to clear.
BUCK0_SC_INT
Latched status bit indicating that the Buck0 output voltage has been over 1 ms below
the short-circuit threshold level.
Write 1 to clear.
0
BUCK0_ILIM_INT
R/W
0
Latched status bit indicating that the Buck0 output current limit has been active.
Write 1 to clear.
7.6.1.29 INT_LDO
INT_LDO is shown in 表 7-65, Address: 0x1C
表 7-64. INT_LDO Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do
not use
LDO1_PG
_INT
LDO1_SC
_INT
LDO1_ILIM
_INT
Reserved - do
not use
LDO0_PG
_INT
LDO0_SC
_INT
LDO0_ILIM
_INT
表 7-65. INT_LDO Register Field Descriptions
Bits
Field
Reserved - do not
Type
Default
Description
7
R/W
0
use
6
5
LDO1_PG_INT
R/W
R/W
0
0
Latched status bit indicating that the LDO1 Power-Good event has been detected.
Write 1 to clear.
LDO1_SC_INT
LDO1_ILIM_INT
Latched status bit indicating that the LDO1 output voltage has been over 1 ms below
the short-circuit threshold level.
Write 1 to clear.
4
3
2
1
R/W
R/W
R/W
R/W
0
0
0
0
Latched status bit indicating that the LDO1 output current limit has been active.
Write 1 to clear.
Reserved - do not
use
LDO0_PG_INT
Latched status bit indicating that the LDO0 Power-Good event has been detected.
Write 1 to clear.
LDO0_SC_INT
Latched status bit indicating that the LDO0 output voltage has been over 1 ms below
the short-circuit threshold level.
Write 1 to clear.
0
LDO0_ILIM_INT
R/W
0
Latched status bit indicating that the LDO0 output current limit has been active.
Write 1 to clear.
7.6.1.30 TOP_STAT
TOP_STAT is shown in 表 7-67, Address: 0x1D
表 7-66. TOP_STAT Register
D7
D6
D5
D4
D3
D2
D1
D0
Copyright © 2021 Texas Instruments Incorporated
52
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
PGOOD_STAT
Reserved - do not use
SYNC_CLK
_STAT
TDIE_SD
_STAT
TDIE_WARN
_STAT
OVP_STAT
Reserved - do
not use
表 7-67. TOP_STAT Register Field Descriptions
Bits
Field
Type
Default
Description
7
PGOOD_STAT
R
0
Status bit indicating the status of the PGOOD pin:
0 - PGOOD pin is inactive.
1 - PGOOD pin is active.
6:5
4
Reserved - do not
use
R
R
00
0
SYNC_CLK_STAT
Status bit indicating the status of the external clock (CLKIN):
0 - External clock frequency is valid.
1 - External clock frequency is not valid.
3
2
1
0
TDIE_SD_STAT
R
R
R
R
0
0
0
0
Status bit indicating the status of the thermal shutdown:
0 - Die temperature below the thermal shutdown level.
1 - Die temperature above the thermal shutdown level.
TDIE_WARN
_STAT
Status bit indicating the status of thermal warning:
0 - Die temperature below the thermal warning level.
1 - Die temperature above the thermal warning level.
OVP_STAT
Status bit indicating the status of the input overvoltage monitoring:
0 - Input voltage is below overvoltage threshold level.
1 - Input voltage above overvoltage threshold level.
Reserved - do not
use
7.6.1.31 BUCK_STAT
BUCK_STAT is shown in 表 7-69, Address: 0x1E
表 7-68. BUCK_STAT Register
D7
D6
D5
D4
D3
D2
D1
D0
BUCK1_STAT
BUCK1_PG
_STAT
Reserved - do
not use
BUCK1_ILIM
_STAT
BUCK0_STAT
BUCK0_PG
_STAT
Reserved - do
not use
BUCK0_ILIM
_STAT
表 7-69. BUCK_STAT Register Field Descriptions
Bits
Field
BUCK1_STAT
Type
Default
Description
7
R
0
Status bit indicating the enable and disable status of the Buck1:
0 - Buck1 regulator is disabled.
1 - Buck1 regulator is enabled.
6
BUCK1_PG_STAT
R
0
Status bit indicating the Buck1 output voltage validity (raw status):
0 - Buck1 output voltage is valid.
1 - Buck1 output voltage is invalid.
5
4
Reserved - do not
use
R
R
0
0
BUCK1_ILIM
_STAT
Status bit indicating the Buck1 current limit status (raw status):
0 - Buck1 output current is below the current limit level.
1 - Buck1 output current limit is active.
3
2
1
BUCK0_STAT
R
R
R
0
0
0
Status bit indicating the enable and disable status of the Buck0:
0 - Buck0 regulator is disabled.
1 - Buck0 regulator is enabled.
BUCK0_PG_STAT
Status bit indicating the Buck0 output voltage validity (raw status):
0 - Buck0 output voltage is valid.
1 - Buck0 output voltage is invalid.
Reserved - do not
use
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
53
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
表 7-69. BUCK_STAT Register Field Descriptions (continued)
Bits
Field
Type
Default
Description
0
BUCK0_ILIM
_STAT
R
0
Status bit indicating the Buck0 current limit status (raw status):
0 - Buck0 output current is below the current limit level.
1 - Buck0 output current limit is active.
7.6.1.32 LDO_STAT
LDO_STAT is shown in 表 7-71, Address: 0x1F
表 7-70. LDO_STAT Register
D7
D6
D5
D4
D3
D2
D1
D0
LDO1_STAT
LDO1_PG
_STAT
Reserved - do
not use
LDO1_ILIM
_STAT
LDO0_STAT
LDO0_PG
_STAT
Reserved - do
not use
LDO0_ILIM
_STAT
表 7-71. LDO_STAT Register Field Descriptions
Bits
Field
Type
Default
Description
7
LDO1_STAT
R
0
Status bit indicating the enable and disable status of the LDO1:
0 - LDO1 regulator is disabled.
1 - LDO1 regulator is enabled.
6
LDO1_PG_STAT
R
0
Status bit indicating the LDO1 output voltage validity (raw status):
0 - LDO1 output voltage is valid.
1 - LDO1 output voltage is invalid.
5
4
Reserved - do not
use
R
R
0
0
LDO1_ILIM
_STAT
Status bit indicating the LDO1 current limit status (raw status):
0 - LDO1 output current is below the current limit level.
1 - LDO1 output current limit is active.
3
2
LDO0_STAT
R
R
0
0
Status bit indicating the enable and disable status of the LDO0:
0 - LDO0 regulator is disabled.
1 - LDO0 regulator is enabled.
LDO0_PG_STAT
Status bit indicating the LDO0 output voltage validity (raw status):
0 - LDO0 output voltage is valid.
1 - LDO0 output voltage is invalid.
1
0
Reserved - do not
use
R
R
0
0
LDO0_ILIM
_STAT
Status bit indicating the LDO0 current limit status (raw status):
0 - LDO0 output current is below the current limit level.
1 - LDO0 output current limit is active.
7.6.1.33 TOP_MASK_1
TOP_MASK_1 is shown in 表 7-73, Address: 0x20
表 7-72. TOP_MASK_1 Register
D7
D6
D5
D4
D3
D2
D1
D0
PGOOD_INT_
MASK
Reserved - do not use
SYNC_CLK
_MASK
Reserved - do
not use
TDIE_WARN
_MASK
Reserved - do
not use
I_LOAD_
READY_MASK
表 7-73. TOP_MASK_1 Register Field Descriptions
Bits
Field
Type
Default
Description
7
PGOOD_INT
_MASK
R/W
1
Masking for Power-Good interrupt (PGOOD_INT in INT_TOP_1 register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the PGOOD_STAT status bit in the TOP_STAT register.
6:5
Reserved - do not
use
R/W
00
Copyright © 2021 Texas Instruments Incorporated
54
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
www.ti.com.cn
Bits
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
表 7-73. TOP_MASK_1 Register Field Descriptions (continued)
Field
Type
Default
Description
4
SYNC_CLK
_MASK
R/W
1
Masking for the external clock detection interrupt (SYNC_CLK_INT in INT_TOP_1
register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the SYNC_CLK_STAT status bit in the TOP_STAT register.
3
2
Reserved - do not
use
R/W
R/W
0
0
TDIE_WARN
_MASK
Masking for the thermal warning interrupt (TDIE_WARN_INT in INT_TOP_1 register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the TDIE_WARN_STAT status bit in the TOP_STAT register.
1
0
Reserved - do not
use
R/W
R/W
0
0
I_MEAS
_MASK
Masking for the load current measurement ready interrupt (MEAS_INT in INT_TOP_1
register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
7.6.1.34 TOP_MASK_2
TOP_MASK_2 is shown in 表 7-75, Address: 0x21
表 7-74. TOP_MASK_2 Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do not use
RESET_REG
_MASK
表 7-75. TOP_MASK_2 Register Field Descriptions
Bits
Field
Type
Default
Description
7:1
Reserved - do not
use
R/W
000 0000
0
RESET_REG
_MASK
R/W
1
Masking for register reset interrupt (RESET_REG_INT in INT_TOP_2 register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This change of this bit by I2C writing has no effect because it will be read from OTP
memory during reset.
7.6.1.35 BUCK_MASK
BUCK_MASK is shown in 表 7-77, Address: 0x22
表 7-76. BUCK_MASK Register
D7
D6
D5
D4
D3
D2
D1
D0
BUCK1_PGF
_MASK
BUCK1_PGR
_MASK
Reserved - do
not use
BUCK1_ILIM
_MASK
BUCK0_PGF
_MASK
BUCK0_PGR
_MASK
Reserved - do
not use
BUCK0_ILIM
_MASK
表 7-77. BUCK_MASK Register Field Descriptions
Bits
Field
Type
Default
Description
7
BUCK1_PGF_MAS
K
R/W
1
Masking of the Power Good invalid detection for the Buck1 power good interrupt
(BUCK1_PG_INT in INT_BUCK register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the BUCK1_PG_STAT status bit in the BUCK_STAT register.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
55
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
表 7-77. BUCK_MASK Register Field Descriptions (continued)
Bits
Field
Type
Default
Description
6
BUCK1_PGR_MAS
K
R/W
1
Masking of the Power Good valid detection for the Buck1 Power Good interrupt
(BUCK1_PG_INT in INT_BUCK register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the BUCK1_PG_STAT status bit in the BUCK_STAT register.
5
4
Reserved - do not
use
R
0
0
BUCK1_ILIM
_MASK
R/W
Masking for the Buck1 current limit detection interrupt (BUCK1_ILIM_INT in
INT_BUCK register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the BUCK1_ILIM_STAT status bit in the BUCK_STAT register.
3
2
BUCK0_PGF_MAS
K
R/W
R/W
1
1
Masking of the Power Good invalid detection for the Buck0 power good interrupt
(BUCK0_PG_INT in INT_BUCK register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect BUCK0_PG_STAT status bit in BUCK_STAT register.
BUCK0_PGR_MAS
K
Masking of the Power Good valid detection for the Buck0 power good interrupt
(BUCK0_PG_INT in INT_BUCK register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the BUCK0_PG_STAT status bit in the BUCK_STAT register.
1
0
Reserved - do not
use
R
0
0
BUCK0_ILIM
_MASK
R/W
Masking for the Buck0 current limit detection interrupt (BUCK0_ILIM_INT in
INT_BUCK register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the BUCK0_ILIM_STAT status bit in the BUCK_STAT register.
7.6.1.36 LDO_MASK
LDO_MASK is shown in 表 7-79, Address: 0x23
表 7-78. LDO_MASK Register
D7
D6
D5
D4
D3
D2
D1
D0
LDO1_PGF
_MASK
LDO1_PGR
_MASK
Reserved - do
not use
LDO1_ILIM
_MASK
LDO0_PGF
_MASK
LDO0_PGR
_MASK
Reserved - do
not use
LDO0_ILIM
_MASK
表 7-79. LDO_MASK Register Field Descriptions
Bits
Field
Type
Default
Description
7
6
LDO1_PGF_MASK
LDO1_PGR_MASK
R/W
1
Masking of the Power Good invalid detection for the LDO1 power good interrupt
(LDO1_PG_INT in INT_LDO register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the LDO1_PG_STAT status bit in the LDO_STAT register.
R/W
1
Masking of the Power Good valid detection for the LDO1 power good interrupt
(LDO1_PG_INT in INT_LDO register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the LDO1_PG_STAT status bit in the LDO_STAT register.
5
4
Reserved - do not
use
R
0
0
LDO1_ILIM
_MASK
R/W
Masking for the LDO1 current limit detection interrupt (LDO1_ILIM_INT in INT_LDO
register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the LDO1_ILIM_STAT status bit in the LDO_STAT register.
Copyright © 2021 Texas Instruments Incorporated
56
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
www.ti.com.cn
Bits
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
表 7-79. LDO_MASK Register Field Descriptions (continued)
Field
Type
Default
Description
3
LDO0_PGF_MASK
R/W
1
Masking of the Power Good invalid detection for the LDO0 power good interrupt
(LDO0_PG_INT in INT_LDO register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the LDO0_PG_STAT status bit in the LDO_STAT register.
2
LDO0_PGR_MASK
R/W
1
0
Masking of Power Good valid detection for the LDO0 power good interrupt
(LDO0_PG_INT in INT_LDO register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the LDO0_PG_STAT status bit in the LDO_STAT register.
1
0
Reserved - do not
use
R
LDO0_ILIM
_MASK
R/W
Masking for the LDO0 current limit detection interrupt (LDO0_ILIM_INT in INT_LDO
register):
0 - Interrupt is generated.
1 - Interrupt is not generated.
This bit does not affect the LDO0_ILIM_STAT status bit in the LDO_STAT register.
7.6.1.37 SEL_I_LOAD
SEL_I_LOAD is shown in 表 7-81, Address: 0x24
表 7-80. SEL_I_LOAD Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do not use
LOAD_CURRE
NT_BUCK
_SELECT
表 7-81. SEL_I_LOAD Register Field Descriptions
Bits
Field
Type
Default
Description
7:1
Reserved - do not
use
R/W
000 0000
0
LOAD_CURRENT_
BUCK_SELECT
R/W
0
Start the current measurement on the selected regulator:
0 - Buck0
1 - Buck1
The measurement is started when the register is written.
7.6.1.38 I_LOAD_2
I_LOAD_2 is shown in 表 7-83, Address: 0x25
表 7-82. I_LOAD_2 Register
D7
D6
D5
D4
D3
D2
D1
D0
Reserved - do not use
BUCK_LOAD_
CURRENT[8]
表 7-83. I_LOAD_2 Register Field Descriptions
Bits
Field
Type
Default
Description
7:1
Reserved - do not
use
R
000 0000
0
BUCK_LOAD_
CURRENT[8]
R
0
This register describes the MSB bit of the average load current on the selected
regulator with a resolution of 20 mA per LSB and maximum 10.22-A current.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
57
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
7.6.1.39 I_LOAD_1
I_LOAD_1 is shown in 表 7-85, Address: 0x26
表 7-84. I_LOAD_1 Register
D7
D6
D5
D4
D3
D2
D1
D0
BUCK_LOAD_CURRENT[7:0]
表 7-85. I_LOAD_1 Register Field Descriptions
Bits
Field
Type
Default
Description
7:0
BUCK_LOAD_
CURRENT[7:0]
R
0000 0000 This register describes 8 LSB bits of the average load current on the selected
regulator with a resolution of 20 mA per LSB and maximum 10.22-A current.
Copyright © 2021 Texas Instruments Incorporated
58
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
8 Application and Implementation
Note
Information in the following applications sections is not part of the TI component specification, and
TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining
suitability of components for their purposes. Customers should validate and test their design
implementation to confirm system functionality.
8.1 Application Information
The LP87332D-Q1 is a power management unit including two step-down regulators, two linear regulators, and
two general-purpose digital output signals.
8.2 Typical Application
L0
VOUT_B0
VIN
VIN_B0
VIN_B1
SW_B0
FB_B0
LOAD
CIN_BUCK0
CIN_BUCK1
COUT_BUCK0
VIN_LDO0
VIN_LDO1
L1
CIN_LDO0
CIN_LDO1
VOUT_B1
SW_B1
FB_B1
LOAD
VANA
CANA
SDA
SCL
nINT
EN
COUT_BUCK1
VOUT_LDO0
VOUT_LDO0
VOUT_LDO1
CLKIN (GPO2)
GPO
VOUT_LDO1
PGOOD
GNDs
COUT_LDO0 COUT_LDO1
Copyright © 2017, Texas Instruments Incorporated
图 8-1. LP87332D-Q1 Typical Application
8.2.1 Design Requirements
8.2.1.1 Inductor Selection
The inductors L0 and L1 are shown in the 节 8.2. The inductance and DCR of the inductor affects the control
loop of the buck regulator. TI recommends using inductors similar to those listed in 表 8-1. Pay attention to the
saturation current and temperature rise current of the inductor. Check that the saturation current is higher than
the peak current limit and the temperature rise current is higher than the maximum expected rms output current.
The minimum effective inductance to ensure good performance is 0.22 μH at maximum peak output current over
the operating temperature range. DC resistance of the inductor must be less than 0.05 Ω for good efficiency
at high-current conditions. The inductor AC loss also affects conversion efficiency. Higher Q factor at switching
frequency usually gives better efficiency at light load to middle load. Shielded inductors are preferred, as they
radiate less noise.
表 8-1. Recommended Inductors
RATED DC CURRENT
ISAT maximum (typical) /
ITEMP maximum (typical) (A)
DCR
typical / maximum
(mΩ)
MANUFACTURER
PART NUMBER
VALUE
DIMENSIONS L × W × H (mm)
TOKO
DFE252012PD-
R47M
0.47 µH (20%)
2.5 × 2 × 1.2
5.2 (–) / 4 (–)(1)
— / 27
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
59
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
表 8-1. Recommended Inductors (continued)
RATED DC CURRENT
DCR
typical / maximum
(mΩ)
MANUFACTURER
PART NUMBER
VALUE
DIMENSIONS L × W × H (mm)
ISAT maximum (typical) /
ITEMP maximum (typical) (A)
Tayo Yuden
MDMK2020TR47MM 0.47 µH (20%)
V
2 × 2 ×1.2
4.2 (4.8) / 2.3 (2.45)
40 / 46
(1) Operating temperature range is up to 125°C including self temperature rise.
8.2.1.2 Buck Input Capacitor Selection
The input capacitors CIN_BUCK0 and CIN_BUCK1 are shown in the 节 8.2. A ceramic input bypass capacitor of 10
μF is required for each phase of the regulator. Place the input capacitor as close as possible to the VIN_Bx
pin and PGND_Bx pin of the device. A larger value or higher voltage rating improves the input voltage filtering.
Use X7R type of capacitors, not Y5V or F. Also, the DC bias characteristics capacitors must be considered.
The minimum effective input capacitance to ensure good performance is 1.9 μF per buck input at maximum
input voltage including tolerances, ambient temperature range, and aging (assuming at least 22 μF of additional
capacitance is common for all the power input pins on the system power rail). See 表 8-2.
The input filter capacitor supplies current to the high-side FET switch in the first half of each cycle and reduces
voltage ripple imposed on the input power source. The low ESR of the ceramic capacitor provides the best
noise filtering of the input voltage spikes due to this rapidly changing current. Select an input filter capacitor with
sufficient ripple current rating. In addition, ferrite can be used in front of the input capacitor to reduce the EMI.
表 8-2. Recommended Buck Input Capacitor (X7R Dielectric)
DIMENSIONS L × W × H
MANUFACTURER
PART NUMBER
VALUE
CASE SIZE
VOLTAGE RATING
(mm)
Murata
GCM21BR71A106KE22
10 µF (10%)
0805
2 × 1.25 × 1.25
10 V
8.2.1.3 Buck Output Capacitor Selection
The output capacitor COUT_BUCK0 and COUT_BUCK1 are shown in 节 8.2. A ceramic local output capacitor of 22 μF
is required per phase. Use ceramic capacitors, X7R type; do not use Y5V or F. DC bias voltage characteristics
of ceramic capacitors must be considered. The output filter capacitor smooths out current flow from the inductor
to the load, which helps maintain a steady output voltage during transient load changes and reduces output
voltage ripple. These capacitors must be selected with sufficient capacitance and sufficiently low ESR and ESL
to perform these functions. The minimum effective output capacitance to ensure good performance is 10 μF per
phase, including the DC voltage rolloff, tolerances, aging, and temperature effects.
The output voltage ripple is caused by the charging and discharging of the output capacitor and due to its RESR
.
The RESR is frequency dependent (and temperature dependent); ensure the value used for selection process is
at the switching frequency of the part. See 表 8-3.
POL capacitors can be used to improve load transient performance and to decrease the ripple voltage. A
higher output capacitance improves the load step behavior, reduces the output voltage ripple, and decreases
the PFM switching frequency. However, output capacitance higher than 150 μF per phase is not necessarily of
any benefit. The output capacitor may be the limiting factor in the output voltage ramp, see 节 6 for maximum
output capacitance for different slew-rate settings. For large output capacitors, the output voltage might be
slower than the programmed ramp rate at voltage transitions, because of the higher energy stored on the output
capacitance. Also at start-up, the time required to charge the output capacitor to target value might be longer. At
shutdown, the output voltage is discharged to a 0.6 V level using forced-PWM operation. This can increase the
input voltage if the load current is small and the output capacitor is large compared to input capacitor. Below the
0.6 V level, the output capacitor is discharged by the internal discharge resistor, and with large capacitor more
time is required to settle VOUT down as a consequence of the increased time constant.
表 8-3. Recommended Buck Output Capacitors (X7R Dielectric)
MANUFACTURER
PART NUMBER
VALUE
CASE SIZE
DIMENSIONS L × W × H
(mm)
VOLTAGE RATING
Murata
GCM31CR71A226KE02
22 µF (10%)
1206
3.2 × 1.6 × 1.6
10 V
Copyright © 2021 Texas Instruments Incorporated
60
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
8.2.1.4 LDO Input Capacitor Selection
The input capacitors CIN_LDO0 and CIN_LDO1 are shown in the 表 8-4. A ceramic input capacitor of 2.2 μF, 6.3
V is sufficient for most applications. Place the input capacitor as close as possible to the VIN_LDOx pin and
AGND pin of the device. A larger value or higher voltage rating improves the input voltage filtering. Use X7R type
of capacitors, not Y5V or F. DC bias characteristics of capacitors must be considered, the minimum effective
input capacitance to ensure good performance is 0.6 μF per LDO input at maximum input voltage including
tolerances, ambient temperature range, and aging. See 表 8-4.
表 8-4. Recommended LDO Input Capacitors (X7R Dielectric)
MANUFACTURER
PART NUMBER
VALUE
CASE SIZE
DIMENSIONS L × W × H
(mm)
VOLTAGE RATING
Murata
Murata
GCM188R70J225KE22
GCM21BR71C475KA73
2.2 µF (10%)
4.7 µF (10%)
0603
0805
1.6 × 0.8 × 0.8
2 × 1.25 × 1.25
6.3 V
16 V
8.2.1.5 LDO Output Capacitor Selection
The output capacitors COUT_LDO0 and COUT_LDO1 are shown in the 节 8.2. A ceramic output capacitor of
minimum 1.0 μF is required. Place the output capacitor as close to the VOUT_LDOx pin and AGND pin of
the device as possible. Use X7R type of capacitors, not Y5V or F. DC bias characteristics of capacitors must be
considered, the minimum effective output capacitance to ensure good performance is 0.4 μF per LDO input at
maximum input voltage including tolerances, ambient temperature range, and aging. See 表 8-5.
Note: the output capcitor requirements excludes any capacitance seen at the point of load and only refers to the
capacitance seen close to the device. Additional capacitance placed near the load can be supported, but the
end applcation system should be evaluated for stability and to ensure the sequencing requirements are met. The
shutdown decay will be longer with higher output capcitance, which can also impact the startup time. Total output
capacitance should be kept below 100 µF.
The output capacitance must be smaller than the input capacitance to ensure the stability of the LDO. With a
1-μF output capacitor, TI recommends using at least a 2.2-μF input capacitor; with a 2.2-μF output capacitor at
least 4.7-μF input capacitance.
The VANA input is used to supply analog and digital circuits in the device. See 表 8-6 for recommended
components from for VANA input supply filtering.
表 8-5. Recommended LDO Output Capacitors (X7R Dielectric)
MANUFACTURER
Murata
PART NUMBER
VALUE
CASE SIZE
DIMENSIONS L × W × H (mm)
VOLTAGE RATING
GCM188R71C105KA64
GCM188R70J225KE22
1 µF (10%)
2.2 µF (10%)
0603
1.6 × 0.8 × 0.8
16 V
Murata
0603
1.6 × 0.8 × 0.8
6.3 V
表 8-6. Recommended Supply Filtering Components
MANUFACTURER
Murata
PART NUMBER
VALUE
CASE SIZE
DIMENSIONS L × W × H (mm)
VOLTAGE RATING
GCM155R71C104KA55 100 nF (10%)
GCM188R71C104KA37 100 nF (10%)
0402
1 × 0.5 × 0.5
16 V
16 V
Murata
0603
1.6 × 0.8 × 0.8
8.2.2 Detailed Design Procedure
The performance of the LP87332D-Q1 device depends greatly on the care taken in designing the printed circuit
board (PCB). The use of low-inductance and low serial-resistance ceramic capacitors is strongly recommended,
while proper grounding is crucial. Attention must be given to decoupling the power supplies. Decoupling
capacitors must be connected close to the device and between the power and ground pins to support high peak
currents being drawn from system power rail during turnon of the switching MOSFETs. Keep input and output
traces as short as possible, because trace inductance, resistance, and capacitance can become performance
limiting items. The separate buck regulator power pins VIN_Bx are not connected together internally. Connect
the VIN_Bx power connections together outside the package using power plane construction.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
61
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
8.2.3 Application Curves
Measurements are done using typical application set up with connections shown in 图 8-1. Graphs may not
reflect the OTP default settings. Unless otherwise specified: V(VIN_Bx) = V(VIN_LDOx) = V(VANA) = 3.7 V, VOUT_Bx = 1
V, VOUT_LDOx = 1 V, TA = 25°C, L = 0.47 µH (TOKO DFE252012PD-R47M), COUT_BUCK = 22 µF , and CPOL_BUCK
= 22 µF, COUT_LDO = 1 µF.
100
90
80
70
60
50
40
100
90
80
70
60
50
40
Vin=5V, AUTO
Vin=3.3V, AUTO
Vin=5V, FPWM
Vin=3.3V, FPWM
Vout=1V
Vout=1.8V
Vout=2.5V
0.001
0.01
0.1
Output Current (A)
1
3
0.001
0.01
0.1
Output Current (A)
1
3
D003
D007
VOUT = 1.8 V
VIN = 3.3 V
图 8-2. Buck Efficiency in PFM/PWM and Forced
图 8-3. Buck Efficiency in Forced PWM Mode
PWM Mode
100
90
80
70
60
1.02
1.016
1.012
1.008
1.004
1
0.996
0.992
0.988
Vout=1V
Vout=1.8V
Vout=2.5V
50
Vin=3.3V, FPWM
0.984
Vin=5.0V, FPWM
0.98
40
0
0.5
1
1.5
Output Current (A)
2
2.5
3
0.001
0.01
0.1
Output Current (A)
1
3
D015
D011
VOUT = 1 V
VIN = 5 V
图 8-5. Buck Output Voltage vs Load Current in
图 8-4. Buck Efficiency in Forced PWM Mode
Forced PWM Mode
1.02
1.015
1.01
1.005
1
1.02
1.016
1.012
1.008
1.004
1
0.996
0.992
0.988
0.984
0.98
0.995
0.99
0.985
0.98
Vin=3.3V, AUTO
Vin=5.0V, AUTO
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
Output Current (A)
1
2.5
3
3.5
4
Input Voltage (V)
4.5
5
5.5
D019
D021
VOUT = 1 V
VOUT = 1 V
Load = 1 A
图 8-6. Buck Output Voltage vs Load Current in
图 8-7. Buck Output Voltage vs Input Voltage in
PFM/PWM Mode
PWM Mode
Copyright © 2021 Texas Instruments Incorporated
62
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
1.02
1.015
1.01
1.005
1
0.995
0.99
0.985
0.98
PFM
PWM
-40
-20
0
20
40
60
80
100 120 140
Temperature (èC)
D023
Slew-rate = 10 mV/µs
ILOAD = 0 A
VOUT = 1 V
Load = 1 A (PWM) and 0.1 A (PFM)
图 8-9. Buck Start-Up With EN1, Forced PWM Mode
图 8-8. Buck Output Voltage vs Temperature
Slew-rate = 10 mV/µs
RLOAD = 1 Ω
VOUT = 1 V
Slew-rate = 10 mV/µs
RLOAD = 1 Ω
VOUT = 1 V
图 8-11. Buck Shutdown With EN1, Forced PWM
图 8-10. Buck Start-Up with EN1, Forced PWM
Mode
Mode
IOUT = 10 mA
IOUT = 200 mA
图 8-12. Buck Output Voltage Ripple, PFM Mode
图 8-13. Buck Output Voltage Ripple, Forced PWM
Mode
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
63
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
图 8-14. Buck Transient From PFM-to-PWM Mode
图 8-15. Buck Transient From PWM-to-PFM Mode
IOUT = 0.1 A → 2 A
→ 0.1 A
TR = TF = 400 ns
IOUT = 0.1 A → 2 A
→ 0.1 A
TR = TF = 400 ns
图 8-16. Buck Transient Load Step Response,
图 8-17. Buck Transient Load Step Response,
AUTO Mode
Forced PWM Mode
VOUT(200mV/div)
VOUT(200mV/div)
Time (400 µs/div)
Time (400 µs/div)
图 8-18. Buck VOUT Transition from 0.6 V to 1.4 V
With Different Slew Rate Settings
图 8-19. Buck VOUT Transition from 1.4 V to 0.6 V
With Different Slew Rate Settings
Copyright © 2021 Texas Instruments Incorporated
64
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
1.02
1.015
1.01
1.005
1
0.995
0.99
0.985
0.98
Vin=3.3V
Vin=5V
0
50
100
150
Output Current (mA)
200
250
300
D050
图 8-20. Buck Start-Up With Short on Output
VOUT = 1 V
图 8-21. LDO Output Voltage vs Load Current
1.02
1.015
1.01
1.005
1
1.02
1.015
1.01
1.005
1
0.995
0.99
0.985
0.98
0.995
0.99
0.985
0.98
-40
-20
0
20
40
60
80
100 120 140
2.5
3
3.5
4
Input Voltage (V)
4.5
5
5.5
Temperature (èC)
D052
D051
VOUT = 1 V
Load = 200 mA
VOUT = 1 V
Load = 200 mA
图 8-23. LDO Output Voltage vs Temperature
图 8-22. LDO Output Voltage vs Input Voltage
ILOAD = 0 A
VOUT = 1 V
RLOAD = 3.3 Ω
VOUT = 1 V
图 8-24. LDO Start-Up
图 8-25. LDO Start-Up
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
65
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
ILOAD = 0 A
VOUT = 1 V
IOUT = 0 A → 0.3 A → 0 A
TR = TF = 1 µs
图 8-26. LDO Shutdown
图 8-28. LDO VOUT Transition from 1.8 V to 1.2 V
Start-up delay is 500 µs
图 8-27. LDO Transient Load Step Response
图 8-29. LDO VOUT Transition from 1.2 V to 1.8 V
图 8-30. LDO Start-Up With Short on Output
9 Power Supply Recommendations
The device is designed to operate from an input voltage supply range between 2.8 V and 5.5 V. The VANA
input and VIN_Bx buck inputs must be connected together, and they must use the same input supply. This
input supply must be well regulated and able to withstand maximum input current and maintain stable voltage
without voltage drop even at load transition condition. The resistance of the input supply rail must be low enough
that the input current transient does not cause too high a drop in the LP87332D-Q1 supply voltage that can
cause false UVLO fault triggering. If the input supply is located more than a few inches from the LP87332D-Q1,
additional bulk capacitance may be required in addition to the ceramic bypass capacitors. The VIN_LDOx LDO
input supply voltage range is 2.5 V to 5.5 V and can be higher or lower than VANA supply voltage.
Copyright © 2021 Texas Instruments Incorporated
66
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
10 Layout
10.1 Layout Guidelines
The high frequency and large switching currents of the LP87332D-Q1 make the choice of layout important. Good
power supply results only occur when care is given to proper design and layout. Layout affects noise pickup
and generation and can cause a good design to perform with less-than-expected results. With a range of output
currents from milliamps to several amps, good power supply layout is much more difficult than most general PCB
design. Use the following steps as a reference to ensure the device is stable and maintains proper voltage and
current regulation across its intended operating voltage and current range.
1. Place CIN as close as possible to the VIN_Bx pin and the PGND_Bx pin. Route the VIN trace wide and
thick to avoid IR drops. The trace between the positive node of the input capacitor and the VIN_Bx pins
of LP87332D-Q1, as well as the trace between the negative node of the input capacitor and the power
PGND_Bx pins, must be kept as short as possible. The input capacitance provides a low-impedance voltage
source for the switching converter. The inductance of the connection is the most important parameter of a
local decoupling capacitor — parasitic inductance on these traces must be kept as small as possible for
proper device operation. The parasitic inductance can be reduced by using a ground plane as close as
possible to the top layer by using thin dielectric layer between the top layer and the ground plane.
2. The output filter, consisting of L and COUT, converts the switching signal at SW_Bx to the noiseless output
voltage. The output filter must be placed as close as possible to the device, keeping the switch node small
for best EMI behavior. Route the traces between the output capacitors of the LP87332D-Q1 and the input
capacitors of the load direct and wide to avoid losses due to the IR drop.
3. Input for analog blocks (VANA and AGND) must be isolated from noisy signals. Connect VANA directly to a
quiet system voltage node and AGND to a quiet ground point where no IR drop occurs. Place the decoupling
capacitor as close as possible to the VANA pin.
4. If remote voltage sensing can be used for the load, connect the LP87332D-Q1 feedback pins FB_Bx to the
respective sense pins on the load capacitor. The sense lines are susceptible to noise. They must be kept
away from noisy signals such as PGND_Bx, VIN_Bx, and SW_Bx, as well as high bandwidth signals such
as the I2C. Avoid both capacitive and inductive coupling by keeping the sense lines short and direct, and
close to each other. Run the lines in a quiet layer. Isolate them from noisy signals by a voltage or ground
plane if possible. If series resistors are used for load current measurement, place them after connection of
the voltage feedback.
5. PGND_Bx, VIN_Bx and SW_Bx must be routed on thick layers. They must not surround inner signal layers
which are not able to withstand interference from noisy PGND_Bx, VIN_Bx and SW_Bx.
6. LDO performance (PSRR, noise, and transient response) depend on the layout of the PCB. Best
performance is achieved by placing CIN and COUT as close to the LP87332D-Q1 device as practical.
The ground connections for CIN and COUT must be back to the LP87332D-Q1 AGND with as wide
and as short of a copper trace as is practical and with multiple vias if routing is done on other layer.
Avoid connections using long trace lengths, narrow trace widths, or connection through small via. These
add parasitic inductances and resistance that results in inferior performance, especially during transient
conditions.
Due to the small package of this converter and the overall small solution size, the thermal performance of the
PCB layout is important. Many system-dependent issues such as thermal coupling, airflow, added heat sinks and
convection surfaces, and the presence of other heat-generating components affect the power dissipation limits
of a given component. Proper PCB layout, focusing on thermal performance, results in lower die temperatures.
Wide power traces can sink dissipated heat. This can be improved further on multi-layer PCB designs with
vias to different planes. This results in reduced junction-to-ambient (RθJA) and junction-to-board (RθJB) thermal
resistances, thereby reducing the device junction temperature, TJ. TI strongly recommends performance of a
careful system-level 2D or full 3D dynamic thermal analysis at the beginning product design process by using a
thermal modeling analysis software.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
67
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
10.2 Layout Example
VOUT0
VOUT1
COUT0
COUT1
GND
L1
L0
21 20 19
17
16
18
15
14
SW_B0
SW_B0
SW_B1
SW_B1
VIN_B1
22
13
12
23
24
CIN0
CIN1
29
AGND
VIN_B0
VIN_B0
VIN
VIN
11
GND
GND
25
VIN_B1
CLKIN
nINT
10
9
GPO
26
27
PGOOD
CIN2
CIN3
8
VIN_LDO0
28
VIN_LDO1
VIN
AGND
VIN
AGND
1
2
3
4
5
6
COUT3
AGND
COUT2
VIN
CANA
AGND
VOUT2
VOUT3
图 10-1. LP87332D-Q1 Board Layout
Copyright © 2021 Texas Instruments Incorporated
68
Submit Document Feedback
Product Folder Links: LP87332D-Q1
LP87332D-Q1
ZHCSGT8A – SEPTEMBER 2017 – REVISED JUNE 2021
www.ti.com.cn
11 Device and Documentation Support
11.1 Device Support
11.1.1 第三方产品免责声明
TI 发布的与第三方产品或服务有关的信息,不能构成与此类产品或服务或保修的适用性有关的认可,不能构成此
类产品或服务单独或与任何 TI 产品或服务一起的表示或认可。
11.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.3 支持资源
TI E2E™ 支持论坛是工程师的重要参考资料,可直接从专家获得快速、经过验证的解答和设计帮助。搜索现有解
答或提出自己的问题可获得所需的快速设计帮助。
链接的内容由各个贡献者“按原样”提供。这些内容并不构成 TI 技术规范,并且不一定反映 TI 的观点;请参阅 TI
的《使用条款》。
11.4 Trademarks
TI E2E™ is a trademark of Texas Instruments.
所有商标均为其各自所有者的财产。
11.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
11.6 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
69
Product Folder Links: LP87332D-Q1
重要声明和免责声明
TI 提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,不保证没
有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他安全、安保或其他要求。这些资源如有变更,恕不另行通知。TI 授权您仅可
将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。您无权使用任何其他 TI 知识产权或任何第三方知
识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款 (https:www.ti.com/legal/termsofsale.html) 或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI
提供这些资源并不会扩展或以其他方式更改 TI 针对 TI 产品发布的适用的担保或担保免责声明。重要声明
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021,德州仪器 (TI) 公司
PACKAGE OPTION ADDENDUM
www.ti.com
27-Sep-2022
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
LP87332DRHDRQ1
LP87332DRHDTQ1
ACTIVE
VQFN
VQFN
RHD
28
28
3000 RoHS & Green
250 RoHS & Green
NIPDAU | SN
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 125
-40 to 125
LP8733
2D-Q1
Samples
Samples
ACTIVE
RHD
NIPDAU | SN
LP8733
2D-Q1
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
27-Sep-2022
OTHER QUALIFIED VERSIONS OF LP87332D-Q1 :
Catalog : LP87332D
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Jan-2023
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LP87332DRHDRQ1
LP87332DRHDTQ1
VQFN
VQFN
RHD
RHD
28
28
3000
250
330.0
180.0
12.4
12.4
5.3
5.3
5.3
5.3
1.1
1.1
8.0
8.0
12.0
12.0
Q2
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Jan-2023
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LP87332DRHDRQ1
LP87332DRHDTQ1
VQFN
VQFN
RHD
RHD
28
28
3000
250
367.0
210.0
367.0
185.0
35.0
35.0
Pack Materials-Page 2
PACKAGE OUTLINE
RHD0028W
VQFN - 1 mm max height
S
C
A
L
E
2
.
5
0
0
PLASTIC QUAD FLATPACK - NO LEAD
5.1
4.9
B
A
PIN 1 INDEX AREA
5.1
4.9
0.1 MIN
(0.05)
A
-
A
2
5
.
0
0
0
SECTION A-A
TYPICAL
C
1 MAX
SEATING PLANE
0.08
0.05
0.00
3.4 0.1
(0.2) TYP
8
14
EXPOSED
THERMAL PAD
24X 0.5
7
15
A
SYMM
A
4X
3
1
21
0.3
28X
0.2
0.1
C A B
28
22
PIN 1 ID
(OPTIONAL)
SYMM
0.05
0.65
0.45
28X
4222120/B 02/2018
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
RHD0028W
VQFN - 1 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
(
3.4)
SYMM
22
28
28X (0.75)
1
21
28X (0.25)
(1.45)
SYMM
(4.65)
(0.5) TYP
15
7
(R0.05) TYP
(
0.2) TYP
VIA
8
14
(1.45)
(4.65)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:15X
0.07 MAX
ALL AROUND
0.07 MIN
ALL AROUND
SOLDER MASK
OPENING
METAL EDGE
EXPOSED
METAL
EXPOSED
METAL
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4222120/B 02/2018
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
www.ti.com
EXAMPLE STENCIL DESIGN
RHD0028W
VQFN - 1 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
SYMM
(0.84) TYP
28
22
METAL
TYP
28X (0.75)
1
21
28X (0.25)
(0.84)
TYP
SYMM
(4.65)
24X (0.5)
7
15
(R0.05) TYP
8
14
4X ( 1.47)
(4.65)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
EXPOSED PAD
75% PRINTED SOLDER COVERAGE BY AREA
SCALE:20X
4222120/B 02/2018
NOTES: (continued)
5. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023,德州仪器 (TI) 公司
相关型号:
©2020 ICPDF网 联系我们和版权申明