LP3992IMFX-1.5/NOPB [TI]
具有使能功能的 30mA、低 IQ、低压降稳压器 | DBV | 5 | -40 to 125;型号: | LP3992IMFX-1.5/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有使能功能的 30mA、低 IQ、低压降稳压器 | DBV | 5 | -40 to 125 光电二极管 输出元件 稳压器 调节器 |
文件: | 总23页 (文件大小:698K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Sample &
Buy
Support &
Community
Product
Folder
Tools &
Software
Technical
Documents
LP3992
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
LP3992 Micropower 1.5-V CMOS Voltage Regulator With Shutdown Control
1 Features
3 Description
The LP3992 regulator is designed to meet the
requirements of portable, battery-powered systems
providing an accurate output voltage, low noise, and
low quiescent current. Battery life is prolonged by the
ability of the LP3992 to provide a 1.5-V output from
the low input voltage of 1.9 V. Additionally, when
switched to a shutdown mode via a logic signal at the
enable (EN) pin, the power consumption is reduced
to virtually zero. The LP3992 also features short-
circuit and thermal-shutdown protection.
1
•
Input Voltage: 1.9 V to 5.2 V
•
•
•
•
•
•
•
•
•
•
•
•
Operation From a Low Input Voltage: 1.9 V
Accurate Output Voltage: 1.5 V ± 0.09 V
Quiescent Current in Shutdown: < 1.5 µA
Stable With an Output Capacitor: 1 µF
Ensured Output Current: 30 mA
Low Output Voltage Noise: 300 µVRMS
Low Quiescent Current: 29-µA Typical
Stable With a Ceramic Capacitor
The LP3992 is designed to be stable with space-
saving ceramic capacitors as small as
Performance is specified for a –40°C to +125°C
temperature range.
1 µF.
Logic Controlled Enable
Fast Turnon and Turnoff
Thermal-Overload and Short-Circuit Protection
–40°C to +125°C Junction Temperature Range
For output voltages other than 1.5 V, and for
additional package options, contact TI.
Device Information(1)
2 Applications
PART NUMBER
LP3992
PACKAGE
BODY SIZE (NOM)
•
•
•
•
•
GSM Portable Phones
SOT-23 (5)
2.90 mm × 1.60 mm
CDMA Cellular Handsets
Wideband CDMA Cellular Handsets
Bluetooth Devices
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Portable Information Appliances
Typical Application
IN
OUT
CAP
VIN
VOUT
CIN
1 mF
LP3992
EN
VEN
High= ON
Low= OFF
COUT
GND
1 mF
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LP3992
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
www.ti.com
Table of Contents
8.2 Functional Block Diagram ....................................... 10
8.3 Feature Description................................................. 11
8.4 Device Functional Modes........................................ 11
Application And Implementation........................ 12
9.1 Application Information .......................................... 12
9.2 Typical Application .................................................. 12
1
2
3
4
5
6
Features.................................................................. 1
Applications ........................................................... 1
Description ............................................................. 1
Revision History..................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings ............................................................ 4
6.3 Recommended Operating Conditions....................... 4
6.4 Thermal Information.................................................. 4
6.5 Electrical Characteristics........................................... 5
6.6 Timing Requirements................................................ 5
6.7 Typical Characteristics............................................. 7
Parameter Measurement Information .................. 9
7.1 Input Test Signals ..................................................... 9
Detailed Description ............................................ 10
8.1 Overview ................................................................. 10
9
10 Power Supply Recommendations ..................... 15
11 Layout................................................................... 15
11.1 Layout Guidelines ................................................. 15
11.2 Layout Example .................................................... 15
12 Device and Documentation Support ................. 16
12.1 Documentation Support ........................................ 16
12.2 Community Resources.......................................... 16
12.3 Trademarks........................................................... 16
12.4 Electrostatic Discharge Caution............................ 16
12.5 Glossary................................................................ 16
7
8
13 Mechanical, Packaging, and Orderable
Information ........................................................... 16
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision B (February 2013) to Revision C
Page
•
Added Device Information and Pin Configuration and Functions sections, ESD Ratings and Thermal Information
tables, Feature Description, Device Functional Modes, Application and Implementation, Power Supply
Recommendations, Layout, Device and Documentation Support, and Mechanical, Packaging, and Orderable
Information sections; update pin names from Vin to IN; Vout to OUT; Cout to CAP and SD to EN ..................................... 1
Deleted lead temperature from Abs Max table - it is in POA ................................................................................................. 4
Added updated thermal information ....................................................................................................................................... 4
•
•
Changes from Revision A (May 2004) to Revision B
Page
•
Changed layout of National Data Sheet to TI format ........................................................................................................... 11
2
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LP3992
LP3992
www.ti.com
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
5 Pin Configuration and Functions
DBV Package
5-Pin SOT-23
Top View
EN
3
GND
2
IN
1
4
5
CAP
OUT
Pin Functions
PIN
TYPE
DESCRIPTION
NO.
1
NAME
IN
Input
Ground
Input
Voltage supply input
Common ground
2
GND
EN
3
Shutdown input — disables the regulator when ≤ 0.4 V, enables the regulator when ≥ 1.15 V.
Output capacitor connection. Internally connected to VOUT connection. This is the
recommended device connection for the 1-µF output capacitor to ensure a stable output.
4
5
CAP
OUT
Output
Output
Voltage output. Connect this output to the load circuit.
Copyright © 2002–2015, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LP3992
LP3992
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)(2)(3)
MIN
–0.3
MAX
6.5
UNIT
V
Input voltage
Output voltage
–0.3 to (VIN + 0.3)
–0.3
6.5
V
Shutdown input voltage
Maximum power dissipation
Junction temperature
Storage temperature, Tstg
6.5
V
568
150
150
mW
°C
°C
–65
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to the potential at the GND pin.
(3) If Military/Aerospace specified devices are required, contact the TI Sales Office/Distributors for availability and specifications.
6.2 ESD Ratings
VALUE
±2000
±200
UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
Machine model
Electrostatic
discharge
V(ESD)
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)(1)
MIN
1.9
0
NOM
MAX
5.2
6
UNIT
V
Input voltage
Shutdown input voltage
Junction temperature
Power dissipation at 25°C
V
–40
125
454
°C
mW
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. For ensured
performance limits and associated test conditions, see Electrical Characteristics.
6.4 Thermal Information
LP3992
THERMAL METRIC(1)
DBV (SOT-23)
5 PINS
170.5
UNIT
RθJA
RθJC(top)
RθJB
ψJT
Junction-to-ambient thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
124.4
30.9
Junction-to-top characterization parameter
Junction-to-board characterization parameter
17.6
ψJB
30.8
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
4
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LP3992
LP3992
www.ti.com
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
6.5 Electrical Characteristics
Unless otherwise noted, VEN = 1.15, VIN = VOUT + 1 V, CIN = 1 µF, IOUT = 1 mA, COUT = 1 µF; typical values and limits apply for
TJ = 25°C, and minimum and maximum limits apply over the full temperature range for operation, −40°C to +125°C.(1)
PARAMETER
Input voltage
TEST CONDITIONS
MIN
1.9
TYP
MAX
5.2
UNIT
mV
VIN
TJ = 25°C
Output voltage tolerance
Over full line and load regulation.
–90
90
mV
VIN = (VOUT(NOM) + 1 V) to 5.2 V,
IOUT = 1 mA
ΔVOUT
Line regulation error
–0.27
0.27
220
%/V
Load regulation error
Load current
IOUT = 1 mA to 30 mA
100
µV/mA
µA
(3)
ILOAD
See(2) and
0
VEN = 1.15 V, IOUT = 0 mA
VEN = 1.15 V, IOUT = 30 mA
VEN = 0.4 V
26
29
50
50
IQ
Quiescent current
µA
0.003
90
1.5
ISC
Short-circuit current limit
See(4)
mA
dB
ƒ = 1 kHz, IOUT = 30 mA
ƒ = 20 kHz, IOUT = 30 mA
BW = 10 Hz to 100 kHz, VIN = 4.2 V
40
PSRR
EEN
Power Supply Rejection Ratio
30
Output noise voltage(3)
300
160
20
µVRMS
°C
Thermal shutdown temperature
Thermal shutdown hysteresis
TSHUTDOWN
ENABLE CONTROL CHARACTERISTICS
Maximum input current at EN
input
IEN
VEN = 0 V and VIN = 5.2 V
0.001
µA
VIL
VIH
Low input threshold
VIN = 1.8 V to 5.2 V
VIN = 1.8 V to 5.2 V
Trise = Tfall = 10 µS(3)
0.4
V
V
High input threshold
1.15
Line transient response |δVOUT
|
60
60
Transient
response
mV
Trise = Tfall = 1 µS
Load transient response |δVOUT
|
IOUT = 100 µA to 5 mA(3)
(1) All limits are ensured. All electrical characteristics having room-temperature limits are tested during production at TJ = 25°C or correlated
using Statistical Quality Control methods. Operation over the temperature specification is specified by correlating the electrical
characteristics to process and temperature variations and applying statistical process control.
(2) The device maintains the regulated output voltage without the load.
(3) This electrical specification is specified by design.
(4) Short-circuit current is measured on the input supply line at the point when the short-circuit condition reduces the output voltage to 95%
of its nominal value.
6.6 Timing Requirements
MIN
NOM
40
MAX
UNIT
µs
(2)
(4)
tON1
Turnon time(1), 50% to 85% of VOUT(NOM)
Turnon time(1) to 95% level(3)
Turnoff time(1), 85% to 50% of VOUT(NOM)
Turnoff time(1), 95% to 5% level(5)
15
tON2
µs
tOFF1
tOFF2
µs
40
15
µs
(1) This electrical specification is ensured by design.
(2) Time for VOUT to rise from 50% to 85% of VOUT(NOM) (Figure 1).
(3) Time from VEN = 1.15 V to VOUT = 95% (VOUT(NOM)) (Figure 1).
(4) Time for VOUT to fall from 85% to 50% of VOUT(NOM) (Figure 1).
(5) Time from VEN = 0.4 V to VOUT = 5% (VOUT(NOM) (Figure 1).
Copyright © 2002–2015, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LP3992
LP3992
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
www.ti.com
Figure 1. tON and tOFF Timing Diagram
6
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LP3992
LP3992
www.ti.com
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
6.7 Typical Characteristics
Unless otherwise specified, CIN = COUT = 1-µF ceramic, VIN = 2.8 V, TA = 25°C, EN pin is tied to VIN.
Figure 2. Output Voltage Change vs Temperature
Figure 3. Ground Current vs Load Current
25°C
125°C
Figure 4. Ground Current vs VIN
Figure 5. Ground Current vs VIN
Figure 6. Short-Circuit Current
Figure 7. Short-Circuit Current
Copyright © 2002–2015, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LP3992
LP3992
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified, CIN = COUT = 1-µF ceramic, VIN = 2.8 V, TA = 25°C, EN pin is tied to VIN.
Figure 8. Line Transient Response
Figure 9. Line Transient Response
Figure 10. Turnon, Turnoff Timing
Figure 11. Turnon, Turnoff Timing
Figure 12. Ripple Rejection
8
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LP3992
LP3992
www.ti.com
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
7 Parameter Measurement Information
7.1 Input Test Signals
Figure 13. Line Transient Input Test Signal
Figure 14. PSRR Input Test Signal
Copyright © 2002–2015, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LP3992
LP3992
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
www.ti.com
8 Detailed Description
8.1 Overview
The LP3992 device is a CMOS voltage regulator with a low-input operating-voltage tolerance. Key protection
circuits, including thermal-overload and short-circuit protection, are integrated in the device. Using the EN pin,
the device may be controlled to provide a SHUTDOWN state, in which negligible supply current is drawn. The
LP3992 is designed to be stable with space-saving ceramic capacitors.
8.2 Functional Block Diagram
OUT
IN
+
Current Limit
Thermal Limit
CAP
V
BG
Fast
Turnoff
+
EN
SD
HI = ON
LOW = OFF
VIH
GND
LP3992
10
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LP3992
LP3992
www.ti.com
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
8.3 Feature Description
8.3.1 Shutdown and Enable
The LP3992 may be switched ON or OFF by a logic input at the EN pin. A high voltage at the EN pin turns the
device on. A low voltage on the EN pin will disable the regulator, and will activate the fast turnoff circuitry to
discharge the output capacitance. When the regulator is disabled the device typically consumes 3 nA.
If the application does not require the EN feature, the EN pin must be tied to VIN to keep the regulator output
permanently on.
To ensure proper operation, the signal source used to drive the EN input must be able to swing above and below
the specified turnon or turnoff voltage thresholds listed in the Electrical Characteristics under VIL and VIH.
8.3.2 Fast Turnon and Turnoff
The controlled shutdown feature of the device provides a fast turn off by discharging the output capacitor via an
internal FET device. This discharge is current limited by the RDSON of this switch. Fast turnon is ensured by
control circuitry within the reference block allowing a very fast ramp of the output voltage to reach the target
voltage.
8.4 Device Functional Modes
8.4.1 Enable Operation
The LP3992 may be switched ON or OFF by a logic input at the EN pin. A high voltage at the EN pin turns the
device on. A low voltage on the EN pin will disable the regulator, and will activate the fast turnoff circuitry to
discharge the output capacitance. When the regulator is disabled the device typically consumes 3 nA.
If the application does not require the EN feature, the EN pin should be tied to VIN to keep the regulator output
permanently on.
To ensure proper operation, the signal source used to drive the EN input must be able to swing above and below
the specified turnon or turnoff voltage thresholds listed in the Electrical Characteristics under VIL and VIH.
Copyright © 2002–2015, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LP3992
LP3992
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
www.ti.com
9 Application And Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The LP3992 can provide 30-mA output current with 1.9-V to 5.2-V input. It is stable with 1-μF ceramic input and
output capacitors. Typical output noise is 300 μVRMS at frequencies from 10 Hz to 100 kHz. Typical power supply
rejection is 40 dB at 1 kHz.
9.2 Typical Application
IN
OUT
CAP
VIN
VOUT
CIN
1 mF
LP3992
EN
VEN
High= ON
Low= OFF
COUT
GND
1 mF
Figure 15. LP3992 Typical Application
9.2.1 Design Requirements
For typical CMOS voltage regulator applications, use the parameters listed in Table 1.
Table 1. Design Parameters
DESIGN PARAMETER
Minimum input voltage
Output voltage
EXAMPLE VALUE
1.9 V
1.5 ± 0.09 V
30 mA
Output current
9.2.2 Detailed Design Procedure
9.2.2.1 External Capacitors
In common with most regulators, the LP3992 requires external capacitors for regulator stability. The device is
specifically designed for portable applications requiring minimum board space and smallest components. These
capacitors must be correctly selected for good performance.
12
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LP3992
LP3992
www.ti.com
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
9.2.2.2 Input Capacitor
An input capacitor is required for stability. It is recommended that a 1-µF capacitor be connected between the
LP3992 IN pin and ground (this capacitance value may be increased without limit).
This capacitor must be located a distance of not more than 1 cm from the IN pin and returned to a clean analog
ground. Any good-quality ceramic, tantalum, or film capacitor may be used at the input.
NOTE
Tantalum capacitors can suffer catastrophic failures due to surge current when connected
to a low-impedance source of power (like a battery or a very large capacitor). If a tantalum
capacitor is used at the input, it must be ensured by the manufacturer to have a surge
current rating sufficient for the application.
There are no requirements for the equivalent series resistance (ESR) on the input capacitor, but tolerance and
temperature coefficient must be considered when selecting the capacitor to ensure the capacitance will remain ≊
1 µF over the entire operating temperature range.
9.2.2.3 Output Capacitor
The LP3992 is designed specifically to work with very small ceramic output capacitors. A 1-µF ceramic capacitor
(dielectric types Z5U, Y5V or X7R) with ESR from 5 mΩ to 500 mΩ, is suitable in the LP3992 application circuit.
For this device the output capacitor should be connected between the CAP pin and ground. It is also possible to
connect the output capacitor directly to the OUT pin. In this case the CAP pin must be left open-circuit or tied
directly to the OUT pin.
Tantalum or film capacitors may also be used at the device output, CAP (or OUT), but these are not as attractive
for reasons of size and cost (see Capacitor Characteristics).
The output capacitor must meet the requirement for the minimum value of capacitance and also have an ESR
value that is within the 5-mΩ to 500-mΩ range for stability.
Table 2. Recommended Output Capacitor
PARAMETER
TEST CONDITIONS
Capacitance(1)
ESR
MIN
0.7
5
TYP
MAX
UNIT
µF
1
COUT
Output capacitor
500
mΩ
(1) The capacitor tolerance should be ±30% or better over the temperature range. The recommended capacitor type is X7R however,
dependant on the application X5R, Y5V, and Z5U can also be used.
9.2.2.4 No-Load Stability
The LP3992 will remain stable and in regulation with no external load. This is an important consideration in some
circuits, for example CMOS RAM keep-alive applications.
9.2.2.5 Capacitor Characteristics
The LP3992 is designed to work with ceramic capacitors on the output to take advantage of the benefits they
offer. For capacitance values in the 1-µF to 4.7-µF range, ceramic capacitors are the smallest, least expensive,
and have the lowest ESR values, thus making them best for eliminating high frequency noise. The ESR of a
typical 1-µF ceramic capacitor is in the 20-mΩ to 40-mΩ range that easily meets the ESR requirement for
stability for the LP3992.
The temperature performance of ceramic capacitors varies by type. Most large-value ceramic capacitors
(≥ 2.2 µF) are manufactured with Z5U or Y5V temperature characteristics, which results in the capacitance
dropping by more than 50% as the temperature goes from 25°C to 85°C.
A better choice for temperature coefficient in a ceramic capacitor is X7R. This type of capacitor is the most stable
and holds the capacitance within ±15% over the temperature range.
Tantalum capacitors are less desirable than ceramic for use as output capacitors because they are more
expensive when comparing equivalent capacitance and voltage ratings in the 1-µF to 4.7-µF range.
Copyright © 2002–2015, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LP3992
LP3992
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
www.ti.com
Another important consideration is that tantalum capacitors have higher ESR values than equivalent size
ceramics. This means that while it may be possible to find a tantalum capacitor with an ESR value within the
stable range, it would have to be larger in capacitance (which means bigger and more costly) than a ceramic
capacitor with the same ESR value. Also, the ESR of a typical tantalum increases about 2:1 as the temperature
goes from 25°C down to –40°C, so some guard band must be allowed.
9.2.2.6 Power Dissipation
The permissible power dissipation for any package is a measure of the capability of the device to pass heat from
the power source, the junctions of the device, to the ultimate heat sink, the ambient environment. Thus, the
power dissipation is dependent on the ambient temperature and the thermal resistance across the various
interfaces between the die and ambient air (see Equation 1).
TA(MAX) = TJ(MAX-OP) − (PD(MAX) × RθJA
)
(1)
(2)
(3)
The allowable power dissipation for the device in a given package can be calculated:
PD = TJ(MAX) – TA / RθJA
The actual power dissipation across the device can be represented by Equation 3:
PD = (VIN − VOUT) × IOUT
This establishes the relationship between the power dissipation allowed due to thermal consideration, the voltage
drop across the device, and the continuous current capability of the device. Equation 2 and Equation 3 must be
used to determine the optimum operating conditions for the device in the application.
This thermal resistance (RθJA) is highly dependent on the heat-spreading capability of the particular PCB design
and therefore varies according to the total copper area, copper weight, and location of the planes. The RθJA
recorded in Thermal Information is determined by the specific EIA/JEDEC JESD51-7 standard for PCB and
copper-spreading area and is to be used only as a relative measure of package thermal performance. For a well-
designed thermal layout, RθJA is actually the sum of the SOT-23 package junction-to-board thermal resistance
(RθJB) plus the thermal resistance contribution by the PCB copper area acting as a heatsink.
9.2.2.7 Estimating Junction Temperature
The EIA/JEDEC standard recommends the use of psi (Ψ) thermal characteristics to estimate the junction
temperatures of surface mount devices on a typical PCB board application. These characteristics are not true
thermal resistance values, but rather package specific thermal characteristics that offer practical and relative
means of estimating junction temperatures. These psi metrics are determined to be significantly independent of
copper-spreading area. The key thermal characteristics (ΨJT and ΨJB) are given in Thermal Information and are
used in accordance with Equation 4 or Equation 5.
TJ(MAX) = TTOP + (ΨJT × PD(MAX)
)
where
•
•
PD(MAX) is explained in Equation 2
TTOP is the temperature measured at the center-top of the device package.
(4)
TJ(MAX) = TBOARD + (ΨJB × PD(MAX)
)
where
•
•
PD(MAX) is explained in Equation 2.
TBOARD is the PCB surface temperature measured 1-mm from the device package and centered on the
package edge.
(5)
For more information about the thermal characteristics ΨJT and ΨJB, see TI Application Report Semiconductor
and IC Package Thermal Metrics (SPRA953); for more information about measuring TTOP and TBOARD, see the TI
Application Report Using New Thermal Metrics (SBVA025); and for more information about the EIA/JEDEC
JESD51 PCB used for validating RθJA, see the TI Application Report Thermal Characteristics of Linear and Logic
Packages Using JEDEC PCB Designs (SZZA017). Aforementioned application notes are available at
www.ti.com.
14
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LP3992
LP3992
www.ti.com
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
9.2.3 Application Curves
Figure 16. Load Transient Response
Figure 17. Load Transient Response
10 Power Supply Recommendations
The LP3992 is designed to operate from an input voltage supply range from 1.9 V to 5.2 V.
11 Layout
11.1 Layout Guidelines
The dynamic performance of the LP3992 is dependant on the layout of the PCB. PCB layout practices that are
adequate for typical LDOs may degrade the PSRR, noise, or transient performance of the device.
Best performance is achieved by placing CIN and COUT on the same side of the PCB as the LP3992 and as close
as is practical to the package. The ground connections for CIN and COUT must be routed back to the LP3992
GND pin using as wide and as short a copper trace as is practical.
Avoid layout connections that have any combination of long trace length, narrow trace width, or vias. These add
parasitic inductances and resistance that result in inferior performance, especially during transient conditions.
11.2 Layout Example
V
V
OUT
IN
IN
OUT
5
C
1
2
3
IN
GND
GND
EN
GND
C
OUT
4
CAP
V
EN
Figure 18. LP3992 Layout Example
Copyright © 2002–2015, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LP3992
LP3992
SNVS192C –OCTOBER 2002–REVISED NOVEMBER 2015
www.ti.com
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
For related documentation see the following:
•
•
•
TI Application Report Semiconductor and IC Package Thermal Metrics (SPRA953)
TI Application Report Using New Thermal Metrics (SBVA025)
TI Application Report Thermal Characteristics of Linear and Logic Packages Using JEDEC PCB Designs
(SZZA017)
12.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.3 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
16
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: LP3992
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
LP3992IMFX-1.5/NOPB
ACTIVE
SOT-23
DBV
5
3000 RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LFHB
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LP3992IMFX-1.5/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SOT-23 DBV
SPQ
Length (mm) Width (mm) Height (mm)
208.0 191.0 35.0
LP3992IMFX-1.5/NOPB
5
3000
Pack Materials-Page 2
PACKAGE OUTLINE
DBV0005A
SOT-23 - 1.45 mm max height
S
C
A
L
E
4
.
0
0
0
SMALL OUTLINE TRANSISTOR
C
3.0
2.6
0.1 C
1.75
1.45
1.45
0.90
B
A
PIN 1
INDEX AREA
1
2
5
(0.1)
2X 0.95
1.9
3.05
2.75
1.9
(0.15)
4
3
0.5
5X
0.3
0.15
0.00
(1.1)
TYP
0.2
C A B
NOTE 5
0.25
GAGE PLANE
0.22
0.08
TYP
8
0
TYP
0.6
0.3
TYP
SEATING PLANE
4214839/G 03/2023
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Refernce JEDEC MO-178.
4. Body dimensions do not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.25 mm per side.
5. Support pin may differ or may not be present.
www.ti.com
EXAMPLE BOARD LAYOUT
DBV0005A
SOT-23 - 1.45 mm max height
SMALL OUTLINE TRANSISTOR
PKG
5X (1.1)
1
5
5X (0.6)
SYMM
(1.9)
2
3
2X (0.95)
4
(R0.05) TYP
(2.6)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:15X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED METAL
EXPOSED METAL
0.07 MIN
ARROUND
0.07 MAX
ARROUND
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4214839/G 03/2023
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DBV0005A
SOT-23 - 1.45 mm max height
SMALL OUTLINE TRANSISTOR
PKG
5X (1.1)
1
5
5X (0.6)
SYMM
(1.9)
2
3
2X(0.95)
4
(R0.05) TYP
(2.6)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:15X
4214839/G 03/2023
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
相关型号:
LP3993IMF-2.85
IC VREG 2.85 V FIXED POSITIVE REGULATOR, PDSO5, SOT-23, 5 PIN, Fixed Positive Single Output Standard Regulator
TI
LP3993IMF-3.0
IC VREG 3 V FIXED POSITIVE REGULATOR, PDSO5, SOT-23, 5 PIN, Fixed Positive Single Output Standard Regulator
TI
LP3993IMF-3.3
IC VREG 3.3 V FIXED POSITIVE REGULATOR, PDSO5, SOT-23, 5 PIN, Fixed Positive Single Output Standard Regulator
TI
LP3993IMFX-1.5
IC VREG 1.5 V FIXED POSITIVE REGULATOR, PDSO5, SOT-23, 5 PIN, Fixed Positive Single Output Standard Regulator
TI
©2020 ICPDF网 联系我们和版权申明