LM3102TL-1/NOPB [TI]
LM3102/-Q1 SIMPLE SWITCHER® Synchronous 1-MHz, 2.5-A Step-Down Voltage Regulator;
| 型号： | LM3102TL-1/NOPB |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | LM3102/-Q1 SIMPLE SWITCHER® Synchronous 1-MHz, 2.5-A Step-Down Voltage Regulator 开关 输出元件 |
| 文件： | 总30页 (文件大小：1448K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Sample &
Buy
Support &
Community
Product
Folder
Tools &
Software
Technical
Documents
LM3102, LM3102-Q1
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
®
LM3102/-Q1 SIMPLE SWITCHER Synchronous 1-MHz, 2.5-A
Step-Down Voltage Regulator
1 Features
•
•
•
Storage Systems
Broadband Infrastructure
1
•
LM3102-Q1 is an Automotive-Grade Product that
is AEC-Q100 Grade 1 Qualified (–40°C to +125°C
Operating Junction Temperature)
Direct Conversion from 2-, 3-, and 4-Cell Lithium
Batteries Systems
•
•
Low Component Count and Small Solution Size
3 Description
Stable With Ceramic and Other Low-ESR
Capacitors
The
LM3102/-Q1
SIMPLE
SWTCHER®
Synchronously Rectified Buck Converter features all
required functions to implement a highly efficient and
cost-effective buck regulator. The device can supply
2.5 A to loads with an output voltage as low as 0.8 V.
Dual N-channel synchronous MOSFET switches
•
•
•
•
•
•
•
•
•
No Loop Compensation Required
High Efficiency at a Light Load by DCM Operation
Prebias Start-Up
Ultra-Fast Transient Response
Programmable Soft-Start
allow
a
low component count, thus reducing
complexity and minimizing board size.
Programmable Switching Frequency up to 1 MHz
Valley Current Limit
Different from most other COT regulators, the
LM3102/-Q1 does not rely on output capacitor ESR
for stability, and is designed to work exceptionally
well with ceramic and other very low-ESR output
Output Overvoltage Protection
Precision Internal Reference for an Adjustable
Output Voltage Down to 0.8 V
capacitors.
The
device
requires
fast load transient
no
loop
compensation, results in
a
•
•
Thermal Shutdown
Key Specifications
response and simple circuit implementation. The
operating frequency remains nearly constant with line
variations due to the inverse relationship between the
input voltage and the ON-time. The operating
frequency can be externally programmed up to
1 MHz. Protection features include VCC undervoltage
lockout (UVLO), output overvoltage protection,
thermal shutdown, and gate drive UVLO. The
LM3102/-Q1 is available in the thermally enhanced
HTSSOP-20 package, and LM3102 is also available
in a DSBGA low-profile chip-scale package with
reduced output current.
–
–
–
–
Input Voltage Range 4.5 V to 42 V
2.5-A Output Current
0.8 V, ±1.5% Reference
Integrated Dual N-Channel Main and
Synchronous MOSFETs
–
Thermally Enhanced HTSSOP-20 Package
2 Applications
•
5-VDC, 12-VDC, 24-VDC, 12-VAC, and 24-VAC
Systems
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
•
•
•
Embedded Systems and Industrial Control
Automotive Telematics and Body Electronics
Point of Load Regulators
LM3102
DSBGA (28)
3.645 mm × 2.45 mm
LM3102
LM3102-Q1
HTSSOP (20)
6.50 mm × 4.40 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Typical Application Schematic
Efficiency vs Load Current (VOUT = 3.3 V)
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM3102, LM3102-Q1
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
www.ti.com
Table of Contents
7.4 Device Functional Modes........................................ 14
Application and Implementation ........................ 16
8.1 Application Information............................................ 16
8.2 Typical Application .................................................. 16
8.3 System Examples ................................................... 20
Power Supply Recommendations...................... 21
1
2
3
4
5
6
Features.................................................................. 1
Applications ........................................................... 1
Description ............................................................. 1
Revision History..................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings.............................................................. 4
6.3 Recommended Operating Conditions....................... 4
6.4 Thermal Information.................................................. 4
6.5 Electrical Characteristics........................................... 5
6.6 Typical Characteristics.............................................. 7
Detailed Description ............................................ 11
7.1 Overview ................................................................. 11
7.2 Functional Block Diagram ....................................... 11
7.3 Feature Description................................................. 11
8
9
10 Layout................................................................... 21
10.1 Layout Guidelines ................................................. 21
10.2 Layout Example .................................................... 21
11 Device and Documentation Support ................. 23
11.1 Related Links ........................................................ 23
11.2 Community Resources.......................................... 23
11.3 Trademarks........................................................... 23
11.4 Electrostatic Discharge Caution............................ 23
11.5 Glossary................................................................ 23
7
12 Mechanical, Packaging, and Orderable
Information ........................................................... 23
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision G (January 2012) to Revision H
Page
•
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
•
Updated the LM3102Q part number to LM3102-Q1 ............................................................................................................. 1
2
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
www.ti.com
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
5 Pin Configuration and Functions
PWP Package
20-Pin HTSSOP
Top View
YPA Package
28–Ball DSBGA
Top View
A
B
C
D
E
F
G
VIN
VIN
BST
SW AGND RON
EN
4
3
2
1
SW
SW
SW
SW
SW
SW
SW AGND AGND AGND
SW
VCC AGND
SS
FB
PGND
PGND PGND PGND VCC AGND
Top Mark
Pin Functions
PIN
TYPE
DESCRIPTION
NAME
PIN NO.
BALL NO.
1
9
10
12
19
20
N/C
—
—
No Connection
A2
A3
B2
B3
C2
C3
D2
D3
D4
A4
B4
C4
E3
E4
F1
F2
F3
G3
G2
—
2
SW
Power
Switching Node
3
4
5
6
VIN
Power
Power
Input supply voltage
BST
Connection for bootstrap capacitor
AGND
7
Ground
Analog Ground
SS
8
Analog
Ground
Analog
Analog
Analog
Soft-Start
Ground
GND
FB
11
13
14
15
G1
G4
F4
E1
E2
Feedback
Enable
EN
RON
ON-time Control
VCC
16
Power
Start-up regulator Output
Copyright © 2007–2015, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
www.ti.com
Pin Functions (continued)
PIN
TYPE
DESCRIPTION
NAME
PGND
EP
PIN NO.
BALL NO.
A1
B1
C1
D1
—
17
Ground
Ground
Power Ground
Exposed Pad
18
EP
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN
–0.3
–0.3
MAX
UNIT
V
VIN, RON to AGND
SW to AGND
43.5
43.5
V
SW to AGND (Transient)
VIN to SW
–2 (< 100 ns)
V
–0.3
–0.3
–0.3
43.5
7
V
BST to SW
V
All Other Inputs to AGND
Junction Temperature, TJ
Storage Temperature, Tstg
7
V
150
150
°C
°C
–65
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings
VALUE
UNIT
V(ESD)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
±2000
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)(1)
MIN
MAX
42
UNIT
Supply Voltage Range (VIN)
4.5
V
Junction Temperature Range (TJ)
−40
125
°C
(1) Absolute Maximum Ratings are limits beyond which damage to the device may occur. Recommended Operating Ratings are conditions
under which operation of the device is intended to be functional. For ensured specifications and test conditions, see the Electrical
Characteristics.
6.4 Thermal Information
LM3102,
LM3102
LM3102-Q1
THERMAL METRIC(1)
UNIT
PWP (HTSSOP) YPA (DSBGA)
20 PINS
30
28 PINS
50
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
°C/W
°C/W
RθJC(top)
6.5
—
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
4
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
www.ti.com
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
6.5 Electrical Characteristics
Specifications with standard type are for TJ = 25°C unless otherwise specified. Minimum and Maximum limits are specified
through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are
provided for reference purposes only. Unless otherwise stated the following conditions apply: VIN = 18 V, VOUT = 3.3 V.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
START-UP REGULATOR, VCC
6
over the full Operating
Junction Temperature
(TJ) range
VCC
VCC output voltage
CCC = 680 nF, no load
V
5
7.2
50
350
65
over the full Operating
Junction Temperature
(TJ) range
ICC = 2mA
200
mV
VIN – VCC
VIN – VCC dropout voltage
over the full Operating
Junction Temperature
(TJ) range
ICC = 20mA
570
VCC current limit(1)
VCC = 0V
mA
over the full Operating
Junction Temperature
(TJ) range
IVCCL
40
3.75
VCC undervoltage lockout
threshold (UVLO)
over the full Operating
Junction Temperature
(TJ) range
VCC-UVLO
VIN increasing
V
3.6
3.9
VCC-UVLO-HYS VCC UVLO hysteresis
VCC-UVLO-HYS VCC UVLO hysteresis
VIN decreasing – HTSSOP package
VIN decreasing – DSBGA package
130
150
3
mV
mV
µs
tVCC-UVLO-D
VCC UVLO filter delay
0.7
over the full Operating
Junction Temperature
(TJ) range
IIN
IIN operating current
No switching, VFB = 1V
mA
1
25
IIN operating current, Device
shutdown
over the full Operating
Junction Temperature
(TJ) range
IIN-SD
VEN = 0V
µA
40
SWITCHING CHARACTERISTICS
0.18
0.11
3.3
RDS-UP-ON
Main MOSFET RDS(on)
Syn. MOSFET RDS(on)
Ω
over the full Operating Junction Temperature (TJ)
range
0.375
RDS- DN-ON
Ω
over the full Operating Junction Temperature (TJ)
range
0.225
over the full Operating
VBST - VSW increasing
VG-UVLO
SOFT-START
ISS
Gate drive voltage UVLO
V
4
Junction Temperature
(TJ) range
8
over the full Operating
VSS = 0.5V
SS pin source current
µA
10
Junction Temperature
(TJ) range
6
(1) VCC provides self bias for the internal gate drive and control circuits. Device thermal limitations limit external loading.
Copyright © 2007–2015, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
www.ti.com
Electrical Characteristics (continued)
Specifications with standard type are for TJ = 25°C unless otherwise specified. Minimum and Maximum limits are specified
through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are
provided for reference purposes only. Unless otherwise stated the following conditions apply: VIN = 18 V, VOUT = 3.3 V.
PARAMETER
CURRENT LIMIT
ICL
TEST CONDITIONS
MIN
TYP
MAX UNIT
Syn. MOSFET current limit
threshold
LM3102
2.7
1.5
A
A
ICL
Syn. MOSFET current limit
threshold
LM3102TLX–1
ON/OFF TIMER
VIN = 10V, RON = 100 kΩ
VIN = 30V, RON = 100 kΩ
1.38
0.47
ton
ON timer pulse width
µs
ON timer minimum pulse
width
ton-MIN
toff
150
260
ns
ns
OFF timer pulse width
ENABLE INPUT
EN Pin input threshold
1.18
over the full Operating
Junction Temperature
(TJ) range
VEN
VEN rising
VEN falling
V
1.13
1.23
VEN-HYS
Enable threshold hysteresis
90
mV
REGULATION AND OVERVOLTAGE COMPARATOR
0.8
VSS ≥ 0.8V
TJ = −40°C to +125°C
over the full Operating
Junction Temperature
(TJ) range
0.784
0.788
0.816
V
VFB
In-regulation feedback voltage
over the full Operating
Junction Temperature
(TJ) range
VSS ≥ 0.8V
TJ = 0°C to +125°C
0.812
0.92
5
VFB-OV
V
Feedback overvoltage
threshold
over the full Operating Junction Temperature (TJ)
range
0.888
0.945
IFB
THERMAL SHUTDOWN
nA
TSD
Thermal shutdown
temperature
TJ rising
TJ falling
165
20
°C
°C
TSD-HYS
Thermal shutdown
temperature hysteresis
6
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
www.ti.com
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
6.6 Typical Characteristics
All curves are taken at VIN = 18 V with the configuration in the typical application circuit for VOUT = 3.3 V shown in this data
sheet. TA = 25°C, unless otherwise specified.
Figure 1. Quiescent Current, IIN vs VIN
Figure 2. VCC vs ICC
Figure 3. VCC vs VIN
Figure 4. ton vs VIN
Figure 5. Switching Frequency, fSW vs VIN
Figure 6. VFB vs Temperature
Copyright © 2007–2015, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
www.ti.com
Typical Characteristics (continued)
All curves are taken at VIN = 18 V with the configuration in the typical application circuit for VOUT = 3.3 V shown in this data
sheet. TA = 25°C, unless otherwise specified.
Figure 8. Efficiency vs Load Current (VOUT = 3.3 V)
Figure 7. RDS(on) vs Temperature
Figure 9. VOUT Regulation vs Load Current (VOUT = 3.3 V)
Figure 10. Efficiency vs Load Current (VOUT = 0.8 V)
Figure 12. Power Up (VOUT = 3.3 V, 2.5 A Loaded)
Figure 11. VOUT Regulation vs Load Current (VOUT = 0.8 V)
8
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
www.ti.com
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
Typical Characteristics (continued)
All curves are taken at VIN = 18 V with the configuration in the typical application circuit for VOUT = 3.3 V shown in this data
sheet. TA = 25°C, unless otherwise specified.
Figure 13. Enable Transient (VOUT = 3.3 V, 2.5 A Loaded)
Figure 14. Shutdown Transient (VOUT = 3.3 V, 2.5 A Loaded)
Figure 15. Continuous Mode Operation (VOUT = 3.3 V, 2.5 A
Loaded)
Figure 16. Discontinuous Mode Operation (VOUT = 3.3 V,
0.025 A Loaded)
Figure 17. DCM to CCM Transition (VOUT = 3.3 V,
0.15-A - 2.5-A Load)
Figure 18. Load Transient (VOUT = 3.3 V, 0.25-A - 2.5-A Load,
Current Slew Rate: 2.5 A/µs)
Copyright © 2007–2015, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
www.ti.com
Typical Characteristics (continued)
All curves are taken at VIN = 18 V with the configuration in the typical application circuit for VOUT = 3.3 V shown in this data
sheet. TA = 25°C, unless otherwise specified.
1.8
1.75
1.7
1.65
1.6
1.55
25°C
1.5
0
10
20
30
40
50
INPUT VOLTAGE (V)
Figure 19. DSBGA Valley Current Limit VOUT = 5 V at 25°C
10
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
www.ti.com
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
7 Detailed Description
7.1 Overview
The LM3102/-Q1 Step-Down Switching Regulator features all required functions to implement a cost-effective,
efficient buck power converter capable of supplying 2.5 A to a load. It contains Dual N-channel main and
synchronous MOSFETs. The Constant ON-Time (COT) regulation scheme requires no loop compensation,
results in fast load transient response and simple circuit implementation. The regulator can function properly
even with an all ceramic output capacitor network, and does not rely on the ESR of the output capacitor for
stability. The operating frequency remains constant with line variations due to the inverse relationship between
the input voltage and the ON-time. The valley current limit detection circuit, with the limit set internally at 2.7 A,
inhibits the main MOSFET until the inductor current level subsides.
The LM3102/-Q1 can be applied in numerous applications and can operate efficiently for inputs as high as 42 V.
Protection features include output overvoltage protection, thermal shutdown, VCC UVLO, gate drive UVLO. The
LM3102/-Q1 is available in the thermally enhanced HTSSOP-20 package.
7.2 Functional Block Diagram
7.3 Feature Description
7.3.1 COT Control Circuit Overview
COT control is based on a comparator and a one-shot ON-timer, with the output voltage feedback (feeding to the
FB pin) compared with an internal reference of 0.8 V. If the voltage of the FB pin is below the reference, the main
MOSFET is turned on for a fixed ON-time determined by a programming resistor RON and the input voltage VIN,
upon which the ON-time varies inversely. Following the ON-time, the main MOSFET remains off for a minimum
of 260 ns. Then, if the voltage of the FB pin is below the reference, the main MOSFET is turned on again for
another ON-time period. The switching will continue to achieve regulation.
Copyright © 2007–2015, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
www.ti.com
Feature Description (continued)
The regulator will operate in the discontinuous conduction mode (DCM) at a light load, and the continuous
conduction mode (CCM) with a heavy load. In the DCM, the current through the inductor starts at zero and
ramps up to a peak during the ON-time, and then ramps back to zero before the end of the OFF-time. It remains
zero and the load current is supplied entirely by the output capacitor. The next ON-time period starts when the
voltage at the FB pin falls below the internal reference. The operating frequency in the DCM is lower and varies
larger with the load current as compared with the CCM. Conversion efficiency is maintained because conduction
loss and switching loss are reduced with the reduction in the load and the switching frequency, respectively. The
operating frequency in the DCM can be calculated approximately as follows:
VOUT (VIN - 1) x L x 1.18 x 1020 x IOUT
fSW
=
2
(VIN ± VOUT) x RON
(1)
In the continuous conduction mode (CCM), the current flows through the inductor in the entire switching cycle,
and never reaches zero during the OFF-time. The operating frequency remains relatively constant with load and
line variations. The CCM operating frequency can be calculated approximately as follows:
VOUT
fSW
=
1.3 x 10-10 x RON
(2)
The output voltage is set by two external resistors RFB1 and RFB2. The regulated output voltage is
VOUT = 0.8V x (RFB1 + RFB2)/RFB2
(3)
7.3.2 Start-Up Regulator (VCC
)
A startup regulator is integrated within the LM3102/-Q1. The input pin VIN can be connected directly to a line
voltage up to 42 V. The VCC output regulates at 6 V, and is current limited to 65 mA. Upon power up, the
regulator sources current into an external capacitor CVCC, which is connected to the VCC pin. For stability, CVCC
must be at least 680 nF. When the voltage on the VCC pin is higher than the UVLO threshold of 3.75 V, the main
MOSFET is enabled and the SS pin is released to allow the soft-start capacitor CSS to charge.
The minimum input voltage is determined by the dropout voltage of the regulator and the VCC UVLO falling
threshold (≊3.7 V). If VIN is less than ≊4.0 V, the regulator shuts off and VCC goes to zero.
7.3.3 Regulation Comparator
The feedback voltage at the FB pin is compared to a 0.8-V internal reference. In normal operation (the output
voltage is regulated), an ON-time period is initiated when the voltage at the FB pin falls below 0.8 V. The main
MOSFET stays on for the ON-time, causing the output voltage and consequently the voltage of the FB pin to rise
above 0.8 V. After the ON-time period, the main MOSFET stays off until the voltage of the FB pin falls below 0.8
V again. Bias current at the FB pin is nominally 5 nA.
7.3.4 Zero Coil Current Detect
The current of the synchronous MOSFET is monitored by a zero coil current detection circuit which inhibits the
synchronous MOSFET when its current reaches zero until the next ON-time. This circuit enables the DCM
operation, which improves the efficiency at a light load.
7.3.5 Overvoltage Comparator
The voltage at the FB pin is compared to a 0.92-V internal reference. If the voltage rises above 0.92 V, the ON-
time is immediately terminated. This condition is known as overvoltage protection (OVP). It can occur if the input
voltage or the output load changes suddenly. Once the OVP is activated, the main MOSFET remains off until the
voltage at the FB pin falls below 0.92 V. The synchronous MOSFET will stay on to discharge the inductor until
the inductor current reduces to zero, and then switch off.
12
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
www.ti.com
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
Feature Description (continued)
7.3.6 Current Limit
Current limit detection is carried out during the OFF-time by monitoring the re-circulating current through the
synchronous MOSFET. Referring to the Functional Block Diagram, when the main MOSFET is turned off, the
inductor current flows through the load, the PGND pin and the internal synchronous MOSFET. If this current
exceeds 2.7 A, the current limit comparator toggles, and as a result disabling the start of the next ON-time
period. The next switching cycle starts when the re-circulating current falls back below 2.7 A (and the voltage at
the FB pin is below 0.8V). The inductor current is monitored during the ON-time of the synchronous MOSFET. As
long as the inductor current exceeds 2.7 A, the main MOSFET will remain inhibited to achieve current limit. The
operating frequency is lower during current limit due to a longer OFF-time.
Figure 20 illustrates an inductor current waveform. On average, the output current IOUT is the same as the
inductor current IL, which is the average of the rippled inductor current. In case of current limit (the current limit
portion of Figure 20), the next ON-time will not initiate until that the current drops below 2.7 A (assume the
voltage at the FB pin is lower than 0.8 V). During each ON-time the current ramps up an amount equal to:
(VIN - VOUT) x ton
ILR
=
L
(4)
During current limit, the LM3102/-Q1 operates in a constant current mode with an average output current IOUT(CL)
equal to 2.7 A + ILR / 2.
Figure 20. Inductor Current - Current Limit Operation
7.3.7 N-Channel MOSFET and Driver
The LM3102/-Q1 integrates an N-channel main MOSFET and an associated floating high voltage main MOSFET
gate driver. The gate drive circuit works in conjunction with an external bootstrap capacitor CBST and an internal
high voltage diode. CBST connecting between the BST and SW pins powers the main MOSFET gate driver during
the main MOSFET ON-time. During each OFF-time, the voltage of the SW pin falls to approximately -1 V, and
CBST charges from VCC through the internal diode. The minimum OFF-time of 260 ns provides enough time for
charging CBST in each cycle.
7.3.8 Soft-Start
The soft-start feature allows the converter to gradually reach a steady-state operating point, thereby reducing
startup stresses and current surges. Upon turnon, after VCC reaches the undervoltage threshold, an 8-µA internal
current source charges up an external capacitor CSS connecting to the SS pin. The ramping voltage at the SS pin
(and the non-inverting input of the regulation comparator as well) ramps up the output voltage VOUT in a
controlled manner.
Copyright © 2007–2015, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
www.ti.com
Feature Description (continued)
An internal switch grounds the SS pin if any of the following three cases happens: (i) VCC is below the UVLO
threshold; (ii) a thermal shutdown occurs; or (iii) the EN pin is grounded. Alternatively, the output voltage can be
shut off by connecting the SS pin to ground using an external switch. Releasing the switch allows the SS pin to
ramp up and the output voltage to return to normal. The shutdown configuration is shown in Figure 21.
Figure 21. Alternate Shutdown Implementation
7.3.9 Thermal Protection
The junction temperature of the LM3102/-Q1 should not exceed the maximum limit. Thermal protection is
implemented by an internal Thermal Shutdown circuit, which activates (typically) at 165°C to make the controller
enter a low power reset state by disabling the main MOSFET, disabling the ON-timer, and grounding the SS pin.
Thermal protection helps prevent catastrophic failures from accidental device overheating. When the junction
temperature falls back below 145°C (typical hysteresis = 20°C), the SS pin is released and normal operation
resumes.
7.3.10 Thermal Derating
The LM3102/-Q1 can supply 2.5 A below an ambient temperature of 100°C. Under worst-case operation, with
either input voltage up to 42 V, operating frequency up to 1 MHz, or voltage of the RON pin below the absolute
maximum of 7 V, the LM3102/-Q1 can deliver a minimum of 1.9-A output current without thermal shutdown with
a PCB ground plane copper area of 40 cm2, 2 oz/Cu. Figure 22 shows a thermal derating curve for the minimum
output current without thermal shutdown against ambient temperature up to 125°C. Obtaining 2.5-A output
current is possible by increasing the PCB ground plane area, or reducing the input voltage or operating
frequency.
Figure 22. Thermal Derating Curve
7.4 Device Functional Modes
7.4.1 ON-Time Timer, Shutdown
The ON-time of the LM3102/-Q1 main MOSFET is determined by the resistor RON and the input voltage VIN. It is
calculated as follows:
1.3 x 10-10 x RON
ton
=
VIN
(5)
14
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
www.ti.com
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
Device Functional Modes (continued)
The inverse relationship of ton and VIN gives a nearly constant frequency as VIN is varied. RON should be selected
such that the ON-time at maximum VIN is greater than 150 ns. The ON-timer has a limiter to ensure a minimum
of 150 ns for ton. This limits the maximum operating frequency, which is governed by Equation 6:
VOUT
fSW(MAX)
=
VIN(MAX) x 150 ns
(6)
The LM3102/-Q1 can be remotely shutdown by pulling the voltage of the EN pin below 1 V. In this shutdown
mode, the SS pin is internally grounded, the ON-timer is disabled, and bias currents are reduced. Releasing the
EN pin allows normal operation to resume because the EN pin is internally pulled up.
Figure 23. Shutdown Implementation
Copyright © 2007–2015, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LM3102/-Q1 is a step-down DC-to-DC controller. It is typically used to convert a higher DC voltage to a
lower DC voltage with a maximum output current of 2.5 A. The following design procedure can be used to select
components for the LM3102/-Q1. Alternately, the WEBENCH software may be used to generate complete
designs.
When generating a design, the WEBENCH® software uses iterative design procedure and accesses
comprehensive databases of components. For more details, go to www.ti.com.
8.2 Typical Application
Figure 24. Typical Application Schematic
8.2.1 Design Requirements
For this example the following application parameters exist.
•
•
•
VIN Range = 8 V to 42 V
VOUT = 3.3 V
IOUT = 2.5 A
Refer to Detailed Design Procedure for more information on operational guidelines and limits.
8.2.2 Detailed Design Procedure
8.2.2.1 Design Steps for the LM3102/-Q1 Application
The LM3102/-Q1 is fully supported by WEBENCH which offers the following: component selection, electrical
simulation, thermal simulation, as well as the build-it prototype board for a reduction in design time. The following
list of steps can be used to manually design the LM3102/-Q1 application.
1. Program VO with divider resistor selection.
2. Program turnon time with soft-start capacitor selection.
3. Select CO.
4. Select CIN.
5. Set operating frequency with RON
.
6. Determine thermal dissipation.
7. Lay out PCB for required thermal performance.
16
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
www.ti.com
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
Typical Application (continued)
8.2.2.2 External Components
The following guidelines can be used to select external components.
RFB1 and RFB2: These resistors should be chosen from standard values in the range of 1.0 kΩ to 10 kΩ,
satisfying the following ratio:
RFB1/RFB2 = (VOUT/0.8 V) – 1
(7)
For VOUT = 0.8 V, the FB pin can be connected to the output directly with a pre-load resistor drawing more than
20 µA. It is because the converter operation needs a minimum inductor current ripple to maintain good regulation
when no load is connected.
RON: Equation 2 can be used to select RON if a desired operating frequency is selected. But the minimum value
of RON is determined by the minimum ON-time. It can be calculated as follows:
VIN(MAX) x 150 ns
RON
t
1.3 x 10-10
(8)
If RON calculated from Equation 2 is smaller than the minimum value determined in Equation 8, a lower frequency
should be selected to recalculate RON by Equation 2. Alternatively, VIN(MAX) can also be limited to keep the
frequency unchanged. The relationship of VIN(MAX) and RON is shown in Figure 25.
On the other hand, the minimum OFF-time of 260 ns can limit the maximum duty ratio. Larger RON should be
selected in any application requiring large duty ratio.
Figure 25. Maximum VIN for Selected RON
L: The main parameter affected by the inductor is the amplitude of inductor current ripple (ILR). Once ILR is
selected, L can be determined by:
VOUT x (VIN - VOUT
)
L =
ILR x fSW x VIN
where
•
•
VIN is the maximum input voltage
fSW is determined from Equation 2
(9)
If the output current IOUT is determined, by assuming that IOUT = IL, the higher and lower peak of ILR can be
determined. Beware that the higher peak of ILR should not be larger than the saturation current of the inductor
and current limits of the main and synchronous MOSFETs. Also, the lower peak of ILR must be positive if CCM
operation is required.
Figure 26 and Figure 27 show curves on inductor selection for various VOUT and RON. For small RON, according
to (8), VIN is limited. Some curves are therefore limited as shown in the figures.
Copyright © 2007–2015, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
www.ti.com
Typical Application (continued)
Figure 26. Inductor Selection for VOUT = 3.3 V
Figure 27. Inductor Selection for VOUT = 0.8 V
CVCC: The capacitor on the VCC output provides not only noise filtering and stability, but also prevents false
triggering of the VCC UVLO at the main MOSFET on/off transitions. CVCC should be no smaller than 680 nF for
stability, and should be a good quality, low-ESR, ceramic capacitor.
COUT and COUT3: COUT should generally be no smaller than 10 µF. Experimentation is usually necessary to
determine the minimum value for COUT, as the nature of the load may require a larger value. A load which
creates significant transients requires a larger COUT than a fixed load.
COUT3 is a small value ceramic capacitor located close to the LM3102/-Q1 to further suppress high frequency
noise at VOUT. A 100-nF capacitor is recommended.
CIN and CIN3: The function of CIN is to supply most of the main MOSFET current during the ON-time, and limit
the voltage ripple at the VIN pin, assuming that the voltage source connecting to the VIN pin has finite output
impedance. If the voltage source’s dynamic impedance is high (effectively a current source), CIN supplies the
average input current, but not the ripple current.
At the maximum load current, when the main MOSFET turns on, the current to the VIN pin suddenly increases
from zero to the lower peak of the inductor’s ripple current and ramps up to the higher peak value. It then drops
to zero at turnoff. The average current during the ON-time is the load current. For a worst case calculation, CIN
must be capable of supplying this average load current during the maximum ON-time. CIN is calculated from:
IOUT x ton
CIN
=
'VIN
where
•
•
•
IOUT is the load current
ton is the maximum ON-time
ΔVIN is the allowable ripple voltage at VIN
(10)
The purpose of CIN3 is to help avoid transients and ringing due to long lead inductance at the VIN pin. A low ESR
0.1-µF ceramic chip capacitor located close to the LM3102/-Q1 is recommended.
CBST: A 33-nF, high-quality ceramic capacitor with low ESR is recommended for CBST because it supplies a
surge current to charge the main MOSFET gate driver at turnon. Low ESR also helps ensure a complete
recharge during each OFF-time.
CSS: The capacitor at the SS pin determines the soft-start time, that is, the time for the reference voltage at the
regulation comparator and the output voltage to reach their final value. The time is determined from the following
equation:
CSS x 0.8V
tSS
=
8 PA
(11)
CFB: If the output voltage is higher than 1.6 V, CFB is needed in the Discontinuous Conduction Mode to reduce
the output ripple. The recommended value for CFB is 10 nF.
18
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
www.ti.com
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
Typical Application (continued)
8.2.3 Application Curve
Figure 28. Efficiency vs Load Current (VOUT = 0.8 V)
Copyright © 2007–2015, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
www.ti.com
8.3 System Examples
Figure 29. Typical Application Schematic for VOUT = 3.3 V
Figure 30. Typical Application Schematic for VOUT = 0.8 V
20
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
www.ti.com
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
9 Power Supply Recommendations
The LM3102/-Q1 device is designed to operate from an input voltage supply range between 4.5 V and 42 V. This
input supply should be well regulated and able to withstand maximum input current and maintain a stable
voltage. The resistance of the input supply rail should be low enough that an input current transient does not
cause a high enough drop at the LM3102/-Q1 supply voltage that can cause a false UVLO fault triggering and
system reset. If the input supply is more than a few inches from the LM3102/-Q1, additional bulk capacitance
may be required in addition to the ceramic bypass capacitors. The amount of bulk capacitance is not critical, but
a 47-μF or 100-μF electrolytic capacitor is a typical choice.
10 Layout
10.1 Layout Guidelines
The LM3102/-Q1 regulation, overvoltage, and current limit comparators are very fast so they will respond to short
duration noise pulses. Layout is therefore critical for optimum performance. It must be as neat and compact as
possible, and all external components must be as close to their associated pins of the LM3102/-Q1 as possible.
Refer to Layout Example, the loop formed by CIN, the main and synchronous MOSFET internal to the LM3102/-
Q1, and the PGND pin should be as small as possible. The connection from the PGND pin to CIN should be as
short and direct as possible. Vias should be added to connect the ground of CIN to a ground plane, located as
close to the capacitor as possible. The bootstrap capacitor CBST should be connected as close to the SW and
BST pins as possible, and the connecting traces should be thick. The feedback resistors and capacitor RFB1
,
RFB2, and CFB should be close to the FB pin.
A long trace running from VOUT to RFB1 is generally acceptable because this is a low-impedance node. Ground
RFB2 directly to the AGND pin (pin 7). The output capacitor COUT should be connected close to the load and tied
directly to the ground plane. The inductor L should be connected close to the SW pin with as short a trace as
possible to reduce the potential for EMI (electromagnetic interference) generation.
If it is expected that the internal dissipation of the LM3102/-Q1 will produce excessive junction temperature
during normal operation, making good use of the PCB ground plane can help considerably to dissipate heat. The
exposed pad on the bottom of the LM3102/-Q1 IC package can be soldered to the ground plane, which should
extend out from beneath the LM3102/-Q1 to help dissipate heat.
The exposed pad is internally connected to the LM3102/-Q1 IC substrate. Additionally the use of thick traces,
where possible, can help conduct heat away from the LM3102/-Q1. Using numerous vias to connect the die
attached pad to the ground plane is a good practice. Judicious positioning of the PCB within the end product,
along with the use of any available air flow (forced or natural convection) can help reduce the junction
temperature.
10.2 Layout Example
L
+
-
CIN
COUT
VSUPPLY
LOAD
Figure 31. Minimize Area of Current Loops in Buck Regulators
Copyright © 2007–2015, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
www.ti.com
Layout Example (continued)
VOUT distribution
point is away
from inductor
and past COUT
VOUT sense point
is away from
inductor and
past COUT
TO LOAD
VOUT
COUT
GND
Route VOUT sense trace away from
SW and VIN nodes. Preferably
shielded in an alternative layer
L
1
NC
NC
NC
SW
SW
20
19
Thermal Vias under DAP
2
3
4
5
6
SW
18
17
PGND
PGND
VCC
CIN
PGND
VIN
VIN
CVCC
RON
VIN
16
15
14
CBOOT
Connect RON
to VIN
RON
EN
BST
Refer Data sheet
for EN options
RFBT
AGND
SS
7
8
9
13
12
11
FB
CSS
NC
NC
RFBB
CFF
NC
10
GND
PAD
(21)
GND Plane
Add as much copper area as possible to enhance overall thermal
performance
Figure 32. PCB Layout Example - Top View
22
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM3102 LM3102-Q1
LM3102, LM3102-Q1
www.ti.com
SNVS515H –SEPTEMBER 2007–REVISED JUNE 2015
11 Device and Documentation Support
11.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 1. Related Links
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
PARTS
PRODUCT FOLDER
SAMPLE & BUY
LM3102
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
LM3102-Q1
11.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.3 Trademarks
E2E is a trademark of Texas Instruments.
SIMPLE SWTCHER, WEBENCH are registered trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2007–2015, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: LM3102 LM3102-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
19-Apr-2015
PACKAGING INFORMATION
Orderable Device
LM3102MH/NOPB
LM3102MHX/NOPB
LM3102QMH/NOPB
LM3102QMHX/NOPB
LM3102TL-1/NOPB
LM3102TLX-1/NOPB
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 125
-40 to 125
-40 to 125
-40 to 125
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
ACTIVE
HTSSOP
HTSSOP
HTSSOP
HTSSOP
DSBGA
PWP
20
20
20
20
28
28
73
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
LM3102
MH
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
PWP
PWP
PWP
YPA
YPA
2500
73
Green (RoHS
& no Sb/Br)
CU SN
LM3102
MH
Green (RoHS
& no Sb/Br)
CU SN
LM3102
QMH
2500
250
Green (RoHS
& no Sb/Br)
CU SN
LM3102
QMH
Green (RoHS
& no Sb/Br)
SNAGCU
SNAGCU
3102
DSBGA
1000
Green (RoHS
& no Sb/Br)
3102
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
19-Apr-2015
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LM3102, LM3102-Q1 :
Catalog: LM3102
•
Automotive: LM3102-Q1
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Oct-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM3102MHX/NOPB
HTSSOP PWP
20
20
28
28
2500
2500
250
330.0
330.0
178.0
178.0
16.4
16.4
12.4
12.4
6.95
6.95
2.64
2.64
7.1
7.1
1.6
1.6
8.0
8.0
8.0
8.0
16.0
16.0
12.0
12.0
Q1
Q1
Q1
Q1
LM3102QMHX/NOPB HTSSOP PWP
LM3102TL-1/NOPB
LM3102TLX-1/NOPB
DSBGA
DSBGA
YPA
YPA
3.84
3.84
0.76
0.76
1000
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Oct-2015
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LM3102MHX/NOPB
LM3102QMHX/NOPB
LM3102TL-1/NOPB
LM3102TLX-1/NOPB
HTSSOP
HTSSOP
DSBGA
DSBGA
PWP
PWP
YPA
YPA
20
20
28
28
2500
2500
250
367.0
367.0
210.0
210.0
367.0
367.0
185.0
185.0
35.0
35.0
35.0
35.0
1000
Pack Materials-Page 2
MECHANICAL DATA
PWP0020A
MXA20A (Rev C)
www.ti.com
MECHANICAL DATA
YPA0028
D
0.600
±0.075
E
TLC28XXX (Rev A)
D: Max = 3.676 mm, Min =3.615 mm
E: Max = 2.48 mm, Min =2.419 mm
4215064/A
12/12
A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
NOTES:
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
相关型号：
LM3102TLX-1/NOPB
LM3102/-Q1 SIMPLE SWITCHER® Synchronous 1-MHz, 2.5-A Step-Down Voltage Regulator
TI
LM3103MH/NOPB
IC SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16, PLASTIC, TSSOP-16, Switching Regulator or Controller
NSC
LM3103MHX/NOPB
IC SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16, LEAD FREE, PLASTIC, TSSOP-16, Switching Regulator or Controller
NSC
©2020 ICPDF网 联系我们和版权申明