LM139-N_14 [TI]
LM139/LM239/LM339/LM2901/LM3302 Low Power Low Offset Voltage Quad Comparators;
| 型号： | LM139-N_14 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | LM139/LM239/LM339/LM2901/LM3302 Low Power Low Offset Voltage Quad Comparators |
| 文件： | 总30页 (文件大小：1593K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
www.ti.com
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
LM139/LM239/LM339/LM2901/LM3302 Low Power Low Offset Voltage Quad Comparators
Check for Samples: LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
1
FEATURES
APPLICATIONS
2
•
Wide Supply Voltage Range
•
•
•
•
•
Limit Comparators
•
•
•
•
LM139/139A Series 2 to 36 VDCor ±1 to ±18 VDC
LM2901: 2 to 36 VDCor ±1 to ±18 VDC
LM3302: 2 to 28 VDCor ±1 to ±14 VDC
Simple Analog-to-Digital Converters
Pulse, Squarewave and Time Delay Generators
Wide Range VCO; MOS Clock Timers
Very Low Supply Current Drain (0.8 mA) —
Independent of Supply Voltage
Multivibrators and High Voltage Digital Logic
Gates
•
•
•
•
Low Input Biasing Current: 25 nA
Low Input Offset Current: ±5 nA
Offset Voltage: ±3 mV
DESCRIPTION
The LM139 series consists of four independent
precision voltage comparators with an offset voltage
specification as low as 2 mV max for all four
comparators. These were designed specifically to
operate from a single power supply over a wide range
of voltages. Operation from split power supplies is
also possible and the low power supply current drain
is independent of the magnitude of the power supply
voltage. These comparators also have a unique
characteristic in that the input common-mode voltage
range includes ground, even though operated from a
single power supply voltage.
Input Common-Mode Voltage Range Includes
GND
•
•
•
Differential Input Voltage Range Equal to the
Power Supply Voltage
Low Output Saturation Voltage: 250 mV at 4
mA
Output Voltage Compatible with TTL, DTL,
ECL, MOS and CMOS Logic Systems
ADVANTAGES
The LM139 series was designed to directly interface
with TTL and CMOS. When operated from both plus
and minus power supplies, they will directly interface
with MOS logic— where the low power drain of the
•
•
•
•
•
•
High Precision Comparators
Reduced VOS Drift Over Temperature
Eliminates Need for Dual Supplies
Allows Sensing Near GND
LM339 is
a distinct advantage over standard
comparators.
Compatible with all Forms of Logic
Power Drain Suitable for Battery Operation
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1999–2013, Texas Instruments Incorporated
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
www.ti.com
One-Shot Multivibrator with Input Lock Out
Connection Diagrams
Figure 1. CDIP, SOIC, PDIP Packages – Top View
See Package Numbers J0014A, D0014A, NFF0014A
Figure 2. CLGA Package
See Package Numbers NAD0014B, NAC0014A
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
www.ti.com
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
Absolute Maximum Ratings(1)
LM139/LM239/LM339
LM139A/LM239A/LM339A
LM2901
LM3302
Supply Voltage, V+
Differential Input Voltage(2)
36 VDC or ±18 VDC
36 VDC
28 VDC or ±14 VDC
28 VDC
Input Voltage
−0.3 VDC to +36 VDC
50 mA
−0.3 VDC to +28 VDC
50 mA
(3)
Input Current (VIN<−0.3 VDC
Power Dissipation(4)
PDIP
)
1050 mW
1190 mW
1050 mW
Cavity DIP
SOIC Package
760 mW
Output Short-Circuit to GND(5)
Storage Temperature Range
Lead Temperature (Soldering, 10 seconds)
Operating Temperature Range
LM339/LM339A
Continuous
−65°C to +150°C
260°C
Continuous
−65°C to +150°C
260°C
−40°C to +85°C
0°C to +70°C
−25°C to +85°C
−40°C to +85°C
−55°C to +125°C
LM239/LM239A
LM2901
LM139/LM139A
Soldering Information
PDIP Package Soldering (10 seconds)
SOIC Package
260°C
260°C
Vapor Phase (60 seconds)
Infrared (15 seconds)
215°C
220°C
600V
215°C
220°C
600V
ESD rating (1.5 kΩ in series with 100 pF)
(1) Refer to RETS139AX for LM139A military specifications and to RETS139X for LM139 military specifications.
(2) Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode
range, the comparator will provide a proper output state. The low input voltage state must not be less than −0.3 VDC (or 0.3 VDCbelow
the magnitude of the negative power supply, if used) (at 25°C).
(3) This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of
the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is
also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the comparators to go
to the V+ voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive
and normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than −0.3 VDC (at
25°C).
(4) For operating at high temperatures, the LM339/LM339A, LM2901, LM3302 must be derated based on a 125°C maximum junction
temperature and a thermal resistance of 95°C/W which applies for the device soldered in a printed circuit board, operating in a still air
ambient. The LM239 and LM139 must be derated based on a 150°C maximum junction temperature. The low bias dissipation and the
“ON-OFF” characteristic of the outputs keeps the chip dissipation very small (PD≤100 mW), provided the output transistors are allowed
to saturate.
(5) Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 20 mA independent of the magnitude of V+.
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
www.ti.com
Electrical Characteristics
(V+=5 VDC, TA = 25°C, unless otherwise stated)
LM139A
Typ
LM239A, LM339A
LM139
Typ
2.0
Parameter
Test Conditions
Units
Min
Max
2.0
Min
Typ
1.0
25
Max
2.0
Min
Max
Input Offset Voltage
Input Bias Current
See(1)
1.0
5.0
mVDC
nADC
IIN(+) or IIN(−) with Output in
Linear Range(2), VCM=0V
25
100
250
25
100
Input Offset Current
I
IN(+)−IIN(−), VCM=0V
3.0
0.8
25
V+−1.5
5.0
50
V+−1.5
3.0
25
nADC
Input Common-Mode
Voltage Range
V+=30 VDC (LM3302,
V+ = 28 VDC
0
0
0
V+−1.5 VDC
(3)
)
Supply Current
RL = ∞ on all Comparators,
RL = ∞, V+ = 36V,
2.0
0.8
1.0
2.0
2.5
0.8
1.0
2.0
2.5
mADC
mADC
(LM3302, V+ = 28 VDC
)
Voltage Gain
RL≥15 kΩ, V+ = 15 VDC
50
200
300
50
200
300
50
200
300
V/mV
ns
VO = 1 VDC to 11 VDC
Large Signal
VIN = TTL Logic Swing, VREF =
Response Time
1.4 VDC, VRL = 5 VDC
,
RL = 5.1 kΩ
Response Time
VRL = 5 VDC, RL = 5.1 kΩ(4)
1.3
16
1.3
16
1.3
16
μs
Output Sink Current
VIN(−) = 1 VDC, VIN(+) = 0,
6.0
6.0
6.0
mADC
V
O ≤ 1.5 VDC
VIN(−) = 1 VDC, VIN(+) = 0,
SINK ≤ 4 mA
Saturation Voltage
250
0.1
400
250
0.1
400
250
0.1
400
mVDC
nADC
I
Output Leakage
Current
VIN(+) = 1 VDC,VIN(−) = 0,
VO = 5 VDC
(1) At output switch point, VO≃1.4 VDC, RS = 0Ω with V+ from 5 VDC to 30 VDC; and over the full input common-mode range (0 VDC to V+
−1.5 VDC), at 25°C. For LM3302, V+ from 5 VDC to 28 VDC
.
(2) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the reference or input lines.
(3) The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end
of the common-mode voltage range is V+ −1.5V at 25°C, but either or both inputs can go to +30 VDC without damage (25V for LM3302),
independent of the magnitude of V+.
(4) The response time specified is a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained, see
typical performance characteristics section.
4
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
www.ti.com
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
Electrical Characteristics
(V+ = 5 VDC, TA = 25°C, unless otherwise stated)
LM239, LM339
LM2901
Min Typ
LM3302
Min Typ
Parameter
Test Conditions
Units
Min Typ
Max
5.0
Max
7.0
Max
20
Input Offset Voltage See(1)
2.0
25
2.0
25
3
mVDC
nADC
Input Bias Current
IIN(+) or IIN(−) with Output in Linear
Range(2), VCM=0V
250
250
25
500
Input Offset Current
Input Common-Mode V+ = 30 VDC (LM3302,
Voltage Range
I
IN(+)−IIN(−), VCM = 0V
5.0
50
V+−1.5
5
50
V+−1.5
3
100
V+−1.5
nADC
VDC
0
0
0
2
V+ = 28 VDC
)
(3)
Supply Current
RL = ∞ on all Comparators,
RL = ∞, V+ = 36V,
0.8
1.0
2.0
2.5
0.8
1.0
2.0
2.5
0.8
1.0
2.0
2.5
mADC
mADC
(LM3302, V+ = 28 VDC
L ≥ 15 kΩ, V+ = 15 VDC
VO = 1 VDC to 11 VDC
VIN = TTL Logic Swing, VREF
)
Voltage Gain
R
50 200
300
25
100
300
30
V/mV
ns
Large Signal
=
300
Response Time
1.4 VDC, VRL = 5 VDC
,
RL = 5.1 kΩ,
Response Time
VRL = 5 VDC, RL = 5.1 kΩ(4)
1.3
1.3
16
1.3
16
μs
Output Sink Current VIN(−)= 1 VDC, VIN(+) = 0,
O ≤ 1.5 VDC
VIN(−) = 1 VDC, VIN(+) = 0,
SINK ≤ 4 mA
6.0
16
250
0.1
6.0
6.0
mADC
V
Saturation Voltage
400
250
0.1
400
250
0.1
500
mVDC
nADC
I
Output Leakage
Current
VIN(+) = 1 VDC,VIN(−) = 0,
VO = 5 VDC
(1) At output switch point, VO≃1.4 VDC, RS = 0Ω with V+ from 5 VDC to 30 VDC; and over the full input common-mode range (0 VDC to V+
−1.5 VDC), at 25°C. For LM3302, V+ from 5 VDC to 28 VDC
.
(2) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the reference or input lines.
(3) The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end
of the common-mode voltage range is V+ −1.5V at 25°C, but either or both inputs can go to +30 VDC without damage (25V for LM3302),
independent of the magnitude of V+.
(4) The response time specified is a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained, see
typical performance characteristics section.
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
www.ti.com
Electrical Characteristics
(1)
(V+ = 5.0 VDC
)
LM139A
Min Typ
LM239A, LM339A
LM139
Min Typ Max
Parameter
Test Conditions
Units
Max
4.0
Min Typ
Max
4.0
Input Offset Voltage
Input Offset Current
Input Bias Current
See(2)
IN(+)−IIN(−), VCM = 0V
9.0
100
300
mVDC
nADC
nADC
I
100
300
150
400
IIN(+) or IIN(−) with Output in
Linear Range, VCM = 0V(3)
Input Common-Mode
Voltage Range
V+=30 VDC (LM3302,
0
V+−2.0
0
V+−2.0
0
V+−2.0
VDC
V+ = 28 VDC
)
(4)
Saturation Voltage
VIN(−)=1 VDC, VIN(+) = 0,
SINK ≤ 4 mA
700
1.0
700
1.0
700
1.0
mVDC
I
Output Leakage Current
Differential Input Voltage
VIN(+) = 1 VDC, VIN(−) = 0,
VO = 30 VDC, (LM3302,
μADC
VO = 28 VDC
)
Keep all VIN's ≥ 0 VDC (or V−, if
36
36
36
VDC
used)(5)
(1) These specifications are limited to −55°C ≤ TA ≤ +125°C, for the LM139/LM139A. With the LM239/LM239A, all temperature
specifications are limited to −25°C ≤ TA ≤ +85°C, the LM339/LM339A temperature specifications are limited to 0°C ≤ TA ≤ +70°C, and
the LM2901, LM3302 temperature range is −40°C ≤ TA ≤ +85°C.
(2) At output switch point, VO≃1.4 VDC, RS = 0Ω with V+ from 5 VDC to 30 VDC; and over the full input common-mode range (0 VDC to V+
−1.5 VDC), at 25°C. For LM3302, V+ from 5 VDC to 28 VDC
.
(3) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the reference or input lines.
(4) The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end
of the common-mode voltage range is V+ −1.5V at 25°C, but either or both inputs can go to +30 VDC without damage (25V for LM3302),
independent of the magnitude of V+.
(5) Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode
range, the comparator will provide a proper output state. The low input voltage state must not be less than −0.3 VDC (or 0.3 VDCbelow
the magnitude of the negative power supply, if used) (at 25°C).
6
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
www.ti.com
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
Electrical Characteristics
(1)
(V+ = 5.0 VDC
)
LM239, LM339
LM2901
Min Typ
LM3302
Parameter
Test Conditions
Units
Min Typ
Max
9.0
Max
15
Min Typ
Max
Input Offset Voltage
Input Offset Current
Input Bias Current
See(2)
IN(+)−IIN(−), VCM = 0V
9
40
mVDC
nADC
nADC
I
150
400
50
200
500
300
IIN(+) or IIN(−) with Output in
Linear Range, VCM = 0V(3)
V+ = 30 VDC (LM3302,
200
1000
Input Common-Mode
V+−2.0
0
V+−2.0
0
V+−2.0
VDC
V+ = 28 VDC
See(4)
)
Voltage Range
Saturation Voltage
VIN(−) = 1 VDC, VIN(+) = 0,
SINK ≤ 4 mA
700
1.0
36
400
700
1.0
36
700
1.0
28
mVDC
μADC
VDC
I
Output Leakage Current
Differential Input Voltage
VIN(+) = 1 VDC, VIN(−) = 0, VO = 30
VDC, (LM3302, V O = 28 VDC
)
Keep all VIN's ≥ 0 VDC (or V−, if
used)(5)
(1) These specifications are limited to −55°C ≤ TA ≤ +125°C, for the LM139/LM139A. With the LM239/LM239A, all temperature
specifications are limited to −25°C ≤ TA ≤ +85°C, the LM339/LM339A temperature specifications are limited to 0°C ≤ TA ≤ +70°C, and
the LM2901, LM3302 temperature range is −40°C ≤ TA ≤ +85°C.
(2) At output switch point, VO≃1.4 VDC, RS = 0Ω with V+ from 5 VDC to 30 VDC; and over the full input common-mode range (0 VDC to V+
−1.5 VDC), at 25°C. For LM3302, V+ from 5 VDC to 28 VDC
.
(3) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the reference or input lines.
(4) The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end
of the common-mode voltage range is V+ −1.5V at 25°C, but either or both inputs can go to +30 VDC without damage (25V for LM3302),
independent of the magnitude of V+.
(5) Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode
range, the comparator will provide a proper output state. The low input voltage state must not be less than −0.3 VDC (or 0.3 VDCbelow
the magnitude of the negative power supply, if used) (at 25°C).
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
LM139/LM239/LM339, LM139A/LM239A/LM339A, LM3302
Supply Current
Input Current
Figure 3.
Figure 4.
Response Time for Various Input Overdrives –
Negative Transition
Output Saturation Voltage
Figure 5.
Figure 6.
Response Time for Various Input Overdrives –
Positive Transition
Figure 7.
8
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
www.ti.com
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
Typical Performance Characteristics
LM2901
Supply Current
Input Current
Figure 8.
Figure 9.
Response Time for Various Input Overdrives –
Negative Transition
Output Saturation Voltage
Figure 10.
Figure 11.
Response Time for Various Input Overdrives –
Positive Transition
Figure 12.
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
www.ti.com
Application Hints
The LM139 series are high gain, wide bandwidth devices which, like most comparators, can easily oscillate if the
output lead is inadvertently allowed to capacitively couple to the inputs via stray capacitance. This shows up only
during the output voltage transition intervals as the comparator changes states. Power supply bypassing is not
required to solve this problem. Standard PC board layout is helpful as it reduces stray input-output coupling.
Reducing this input resistors to < 10 kΩ reduces the feedback signal levels and finally, adding even a small
amount (1 to 10 mV) of positive feedback (hysteresis) causes such a rapid transition that oscillations due to stray
feedback are not possible. Simply socketing the IC and attaching resistors to the pins will cause input-output
oscillations during the small transition intervals unless hysteresis is used. If the input signal is a pulse waveform,
with relatively fast rise and fall times, hysteresis is not required.
All pins of any unused comparators should be tied to the negative supply.
The bias network of the LM139 series establishes a drain current which is independent of the magnitude of the
power supply voltage over the range of from 2 VDC to 30 VDC
.
It is usually unnecessary to use a bypass capacitor across the power supply line.
The differential input voltage may be larger than V+ without damaging the device. Protection should be provided
to prevent the input voltages from going negative more than −0.3 VDC (at 25°C). An input clamp diode can be
used as shown in the applications section.
The output of the LM139 series is the uncommitted collector of a grounded-emitter NPN output transistor. Many
collectors can be tied together to provide an output OR'ing function. An output pull-up resistor can be connected
to any available power supply voltage within the permitted supply voltage range and there is no restriction on this
voltage due to the magnitude of the voltage which is applied to the V+ terminal of the LM139A package. The
output can also be used as a simple SPST switch to ground (when a pull-up resistor is not used). The amount of
current which the output device can sink is limited by the drive available (which is independent of V+) and the β
of this device. When the maximum current limit is reached (approximately 16 mA), the output transistor will come
out of saturation and the output voltage will rise very rapidly. The output saturation voltage is limited by the
approximately 60Ω RSAT of the output transistor. The low offset voltage of the output transistor (1 mV) allows the
output to clamp essentially to ground level for small load currents.
10
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
www.ti.com
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
Typical Applications
(V+ = 5.0 VDC
)
Figure 13. Basic Comparator
Figure 14. Driving CMOS
Figure 15. Driving TTL
Figure 16. AND Gate
Figure 17. OR Gate
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
www.ti.com
Typical Applications
(V+= 15 VDC
)
Figure 18. One-Shot Multivibrator
Figure 19. Bi-Stable Multivibrator
12
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
www.ti.com
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
Figure 20. One-Shot Multivibrator with Input Lock Out
Figure 21. Pulse Generator
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
www.ti.com
Figure 22. Large Fan-In AND Gate
Figure 23. ORing the Outputs
14
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
www.ti.com
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
Figure 24. Time Delay Generator
Figure 25. Non-Inverting Comparator with
Figure 26. Inverting Comparator with Hysteresis
Hysteresis
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
www.ti.com
Figure 27. Squarewave Oscillator
Figure 28. Basic Comparator
Figure 29. Limit Comparator
Figure 30. Comparing Input Voltages of Opposite
Polarity
16
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
www.ti.com
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
* Or open-collector logic gate without pull-up resistor
Figure 31. Output Strobing
Figure 32. Crystal Controlled Oscillator
V+ = +30 VDC
250 mVDC ≤ VC ≤ +50 VDC
700 Hz ≤ fO ≤ 100 kHz
Figure 33. Two-Decade High-Frequency VCO
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
www.ti.com
Figure 34. Transducer Amplifier
Figure 35. Zero Crossing Detector (Single Power
Supply)
18
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
www.ti.com
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
Split-Supply Applications
(V+ = +15 VDC and V− = −15 VDC
)
Figure 36. MOS Clock Driver
Figure 37. Zero Crossing Detector
Figure 38. Comparator With a Negative Reference
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
www.ti.com
Schematic Diagram
20
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N
www.ti.com
SNOSBJ3D –NOVEMBER 1999–REVISED MARCH 2013
REVISION HISTORY
Changes from Revision C (March 2013) to Revision D
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 20
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: LM139-N LM239-N LM2901-N LM3302-N LM339-N
PACKAGE OPTION ADDENDUM
www.ti.com
8-Jun-2013
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
LM139AJ/PB
LM139J/PB
LM239J
ACTIVE
CDIP
CDIP
CDIP
SOIC
SOIC
J
14
14
14
14
14
25
TBD
TBD
TBD
TBD
Call TI
Call TI
Call TI
Call TI
CU SN
Call TI
Call TI
-55 to 125
-55 to 125
-25 to 85
-40 to 85
-40 to 85
LM139AJ
ACTIVE
ACTIVE
ACTIVE
ACTIVE
J
J
25
25
55
55
LM139J
Call TI
LM239J
LM2901M
D
D
Call TI
LM2901M
LM2901M
LM2901M/NOPB
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LM2901MX
ACTIVE
ACTIVE
SOIC
SOIC
D
D
14
14
2500
2500
TBD
Call TI
CU SN
Call TI
-40 to 85
-40 to 85
LM2901M
LM2901M
LM2901MX/NOPB
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LM2901N/NOPB
ACTIVE
PDIP
NFF
14
25
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 85
LM2901N
LM2901N/PB
LM339AM
ACTIVE
ACTIVE
ACTIVE
PDIP
SOIC
SOIC
NFF
D
14
14
14
25
55
55
TBD
Call TI
Call TI
CU SN
Call TI
Call TI
LM2901N
LM339AM
LM339AM
TBD
-25 to 85
-25 to 85
LM339AM/NOPB
D
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LM339AMX
ACTIVE
ACTIVE
SOIC
SOIC
D
D
14
14
2500
2500
TBD
Call TI
CU SN
Call TI
-25 to 85
-25 to 85
LM339AM
LM339AM
LM339AMX/NOPB
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LM339AN/NOPB
ACTIVE
PDIP
NFF
14
25
Green (RoHS
& no Sb/Br)
SN
Level-1-NA-UNLIM
-25 to 85
LM339AN
LM339AN/PB
LM339J
ACTIVE
ACTIVE
ACTIVE
ACTIVE
PDIP
CDIP
SOIC
SOIC
NFF
J
14
14
14
14
25
25
55
55
TBD
TBD
TBD
Call TI
Call TI
Call TI
CU SN
Call TI
Call TI
LM339AN
LM339J
-25 to 85
-25 to 85
-25 to 85
LM339M
D
Call TI
LM339M
LM339M
LM339M/NOPB
D
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LM339MX
ACTIVE
SOIC
D
14
2500
TBD
Call TI
Call TI
-25 to 85
LM339M
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
8-Jun-2013
Orderable Device
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-25 to 85
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
LM339MX/NOPB
LM339N/NOPB
ACTIVE
SOIC
PDIP
D
14
14
2500
Green (RoHS
& no Sb/Br)
CU SN
SN
Level-1-260C-UNLIM
LM339M
ACTIVE
NFF
25
Green (RoHS
& no Sb/Br)
Level-1-NA-UNLIM
-25 to 85
LM339N
LM339N/PB
MLM339P
ACTIVE
ACTIVE
PDIP
PDIP
NFF
NFF
14
14
25
25
TBD
Call TI
Call TI
Call TI
Call TI
LM339N
LM339N
TBD
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
8-Jun-2013
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Apr-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM2901MX
LM2901MX/NOPB
LM339AMX
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
D
D
D
D
D
D
14
14
14
14
14
14
2500
2500
2500
2500
2500
2500
330.0
330.0
330.0
330.0
330.0
330.0
16.4
16.4
16.4
16.4
16.4
16.4
6.5
6.5
6.5
6.5
6.5
6.5
9.35
9.35
9.35
9.35
9.35
9.35
2.3
2.3
2.3
2.3
2.3
2.3
8.0
8.0
8.0
8.0
8.0
8.0
16.0
16.0
16.0
16.0
16.0
16.0
Q1
Q1
Q1
Q1
Q1
Q1
LM339AMX/NOPB
LM339MX
LM339MX/NOPB
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Apr-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LM2901MX
LM2901MX/NOPB
LM339AMX
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
D
D
D
D
D
D
14
14
14
14
14
14
2500
2500
2500
2500
2500
2500
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
35.0
35.0
35.0
35.0
35.0
35.0
LM339AMX/NOPB
LM339MX
LM339MX/NOPB
Pack Materials-Page 2
MECHANICAL DATA
NFF0014A
N14A (Rev G)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明