LM101AWLQMLV [TI]
LM101AQML Operational Amplifiers; LM101AQML运算放大器型号: | LM101AWLQMLV |
厂家: | TEXAS INSTRUMENTS |
描述: | LM101AQML Operational Amplifiers |
文件: | 总25页 (文件大小:992K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LM101AQML
LM101AQML Operational Amplifiers
Literature Number: SNOSAI0
January 2006
LM101AQML
Operational Amplifiers
General Description
The LM101A is a general purpose operational amplifier
which features improved performance over industry stan-
dards such as the LM709. Advanced processing techniques
make possible an order of magnitude reduction in input
currents, and a redesign of the biasing circuitry reduces the
temperature drift of input current. Improved specifications
include:
overcompensated for increased stability margin. Or the
compensation can be optimized to give more than a
factor of ten improvement in high frequency performance
for most applications.
In addition, the device provides better accuracy and
lower noise in high impedance circuitry. The low input
currents also make it particularly well suited for long
interval integrators or timers, sample and hold circuits
and low frequency waveform generators. Further, replac-
ing circuits where matched transistor pairs buffer the
inputs of conventional IC op amps, it can give lower offset
voltage and a drift at a lower cost.
•
•
•
•
•
Offset voltage 3 mV maximum over temperature
Input current 100 nA maximum over temperature
Offset current 20 nA maximum over temperature
Guaranteed drift characteristics
Features
Offsets guaranteed over entire common mode and sup-
ply voltage ranges
n Available with radiation guarantee
n Offset voltage 3 mV maximum over temperature
n Input current 100 nA maximum over temperature
n Offset current 20 nA maximum over temperature
n Guaranteed drift characteristics
n Offsets guaranteed over entire common mode and
supply voltage ranges
•
Slew rate of 10V/µs as a summing amplifier
This amplifier offers many features which make its appli-
cation nearly foolproof: overload protection on the input
and output, no latch-up when the common mode range is
exceeded, and freedom from oscillations and compensa-
tion with a single 30 pF capacitor. It has advantages over
internally compensated amplifiers in that the frequency
compensation can be tailored to the particular applica-
tion. For example, in low frequency circuits it can be
n Slew rate of 10 V/µS as a summing amplifier
Ordering Information
NS Part Number
SMD Part Number
NS Package Number
Package Description
8LD Metal Can
8LD CERDIP
LM101AH/883
H08C
J08A
LM101AJ/883
LM101AW/883
LM101AH-QMLV
LM101AHLQMLV
W10A
H08C
H08C
10LD CERPACK
8LD Metal Can
8LD Metal Can
5962–9951501VGA
5962L9951501VGA
50k rd(Si)
LM101AHRQMLV
LM101AJLQMLV
5962R9951501VGA
100k rd(Si)
H08C
J08A
8LD Metal Can
8LD CERDIP
5962L9951501VPA
50k rd(Si)
LM101AJ-QMLV
LM101AW-QMLV
LM101AWLQMLV
5962–9951501VPA
5962–9951501VHA
5962L9951501VHA
50k rd(Si)
J08A
W10A
W10A
8LD CERDIP
10LD CERPACK
10LD CERPACK
© 2006 National Semiconductor Corporation
DS201223
www.national.com
Schematic (Note 11)
20122301
Connection Diagrams
(Top View)
(Top View)
Metal Can Package
Dual-In-Line Package
20122304
See NS Package Number J08A
20122302
See NS Package Number H08C
Note: Pin 4 connected to case.
www.national.com
2
Connection Diagrams (Continued)
(Top View)
Ceramic Flatpack Package
20122340
See NS Package Number W10A
Fast AC/DC Converter
20122333
Note 1: Feedforward compensation can be used to make a fast full wave rectifier without a filter.
3
www.national.com
Absolute Maximum Ratings (Note 2)
Supply Voltage
22V
30V
Differential Input Voltage
Input Voltage (Note 3)
Output Short Circuit Duration
Operating Ambient Temp. Range
TJ Max
15V
Continuous
−55˚C ≤ TA ≤ +125˚C
150˚C
Power Dissipation at TA = 25˚C (Note 4)
H-Package
(Still Air)
750 mW
(500 LF / Min Air Flow)
J-Package
1200 mW
(Still Air)
1000 mW
1500 mW
(500 LF / Min Air Flow)
W-Package
(Still Air)
500mW
800mW
(500 LF / Min Air Flow)
Thermal Resistance
θJA
H-Package
(Still Air)
165˚C/W
89˚C/W
(500 LF / Min Air Flow)
J-Package
(Still Air)
128˚C/W
75˚C/W
(500 LF / Min Air Flow)
W-Package
(Still Air)
233˚C/W
155˚C/W
(500 LF / Min Air Flow)
θJC (Typical)
H-Package
39˚C/W
26˚C/W
J-Package
W-Package
26˚C/W
Storage Temperature Range
Lead Temperature (Soldering, 10 sec.)
ESD Tolerance (Note 5)
−65˚C ≤ TA ≤ +150˚C
300˚C
3000V
www.national.com
4
Quality Conformance Inspection
Mil-Std-883, Method 5005 - Group A
Subgroup
Description
Static tests at
Temp (˚C)
25
1
2
Static tests at
125
-55
3
Static tests at
4
Dynamic tests at
Dynamic tests at
Dynamic tests at
Functional tests at
Functional tests at
Functional tests at
Switching tests at
Switching tests at
Switching tests at
25
5
125
-55
6
7
25
8A
8B
9
125
-55
25
10
11
125
-55
LM101A 883 Electrical Characteristics
DC Parameters
The following conditions apply to all parameters, unless otherwise specified
VCC
=
20V, VCM= 0V
Symbol
Parameter
Conditions
Sub-
groups
1
Notes
Min Max
Units
VIO
Input Offset Voltage
Input Offset Current
Input Bias Current
VCM = -15V, RS = 50Ω
VCM = 15V, RS = 50Ω
RS = 50Ω
-2.0
-3.0
-2.0
-3.0
-2.0
-3.0
-2.0
-3.0
-10
-20
-10
-20
-10
-20
-10
-20
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
2.0
3.0
2.0
3.0
2.0
3.0
2.0
3.0
10
mV
mV
mV
mV
mV
mV
mV
mV
nA
nA
nA
nA
nA
nA
nA
nA
nA
nA
nA
nA
nA
nA
nA
nA
2, 3
1
2, 3
1
2, 3
1
VCC
=
5V, RS = 50Ω
2, 3
1
IIO
VCM = -15V
VCM = 15V
20
2, 3
1
10
20
2, 3
1
10
20
2, 3
1
VCC
=
5V
10
20
2, 3
1
IIB
VCM = -15V
VCM = 15V
75
100
75
2, 3
1
100
75
2, 3
1
100
75
2, 3
1
VCC
=
5V
100
2, 3
PSRR+
PSRR-
CMRR
Power Supply Rejection Ratio
Power Supply Rejection Ratio
+VCC = +20V and +5V,
-VCC=-20V, RS=50Ω
+VCC = +20V,
80
dB
1, 2, 3
80
80
dB
dB
1, 2, 3
1, 2, 3
-VCC= -20V and -5V, RS=50Ω
Common Mode Rejection Ratio -15V ≤ VCM ≤ 15V, RS = 50Ω
5
www.national.com
LM101A 883 Electrical Characteristics (Continued)
DC Parameters (Continued)
The following conditions apply to all parameters, unless otherwise specified
VCC
=
20V, VCM= 0V
Symbol
Parameter
Conditions
Sub-
groups
1
Notes
Min Max
Units
ICC
Supply Current
3.0
2.5
mA
mA
mA
mV
mV
mA
mA
V
2
3.5
3
+VIO Adj
−VIO Adj
+IOS
Input Offset Voltage Adjust
Input Offset Voltage Adjust
Short Circuit Current
Short Circuit Current
Input Voltage Range
Large Signal Gain
4.0
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
4
-4.0
-45
7.0
-15
50
-7.0
45
-IOS
VI
VCC
VCC
=
=
20V
(Note 6)
15
+AVS
15V, RS = 0, RL=2KΩ,
V/mV
V/mV
V/mV
V/mV
MΩ
MΩ
V
VO =10V
25
5, 6
-AVS
RI
Large Signal Gain
Input Resistance
VCC 15V, RS = 0, RL=2KΩ,
=
50
4
VO =-10V
25
5, 6
(Note 7)
(Note 7)
1.5
0.5
16
4
5, 6
+VOP
Output Voltage Swing
RL = 10KΩ
4, 5, 6
4, 5, 6
4, 5, 6
4, 5, 6
4, 5, 6
4, 5, 6
4, 5, 6
4, 5, 6
RL = 2KΩ
15
V
RL = 10KΩ, VCC
=
=
15V
15V
12
V
RL = 2KΩ, VCC
RL = 10KΩ
=
10
V
-VOP
Output Voltage Swing
-16
-15
-12
-10
V
RL = 2KΩ
V
RL = 10KΩ, VCC
15V
15V
V
RL = 2KΩ, VCC
=
V
AC Parameters
The following conditions apply to all parameters, unless otherwise specified
VCC
=
20V, RL = 2KΩ, AV = 1
Symbol
Parameter
Conditions
Sub-
groups
Notes
Min Max
Units
+SR
-SR
Slew Rate
VI = -5V to 5V
0.2
0.2
V/µS
V/µS
MHz
7
7
7
Slew Rate
VI = 5V to -5V
GBW
Gain Bandwidth
VI = 50mVRMS, f = 20KHz
0.25
www.national.com
6
LM101A QML & RH Electrical Characteristics (Note 10)
DC Parameters
The following conditions apply to all parameters, unless otherwise specified
VCC
=
20V, VCM = 0V, RS = 50Ω
Symbol
Parameter
Conditions
Sub-
groups
1
Notes
Min Max
Units
VIO
Input Offset Voltage
Input Offset Current
Input Bias Current
+VCC = 35V, -VCC = -5V,
VCM = -15V
-2.0 +2.0
-3.0 +3.0
-2.0 +2.0
-3.0 +3.0
-2.0 +2.0
-3.0 +3.0
-2.0 +2.0
-3.0 +3.0
mV
mV
mV
mV
mV
mV
mV
mV
nA
2, 3
1
+VCC = 5V, -VCC = -35V,
VCM = +15V
2, 3
1
VCM = 0V
2, 3
1
+VCC = 5V, -VCC = -5V,
VCM = 0V
2, 3
1, 2
3
IIO
+VCC = 35V, -VCC = -5V,
-10
-20
-10
-20
-10
-20
-10
-20
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-50
+10
+20
+10
+20
+10
+20
+10
+20
75
VCM = -15V, RS = 100KΩ
nA
+VCC = 5V, -VCC = -35V,
nA
1, 2
3
VCM = +15V, RS = 100KΩ
nA
VCM = 0V, RS = 100KΩ
nA
1, 2
3
nA
+VCC = 5V, -VCC = -5V,
nA
1, 2
3
VCM = 0V, RS = 100KΩ
nA
IIB
+VCC = 35V, -VCC = -5V,
nA
1, 2
3
VCM = -15V, RS = 100KΩ
100
75
nA
+VCC = 5V, -VCC = -35V,
nA
1, 2
3
VCM = +15V, RS = 100KΩ
100
75
nA
VCM = 0V, RS = 100KΩ
nA
1, 2
3
100
75
nA
+VCC = 5V, -VCC = -5V,
nA
1, 2
3
VCM = 0V, RS = 100KΩ
100
+50
nA
+PSRR
-PSRR
CMRR
+VIO Adj
-VIO Adj
+IOS
Power Supply Rejection Ratio
Power Supply Rejection Ratio
+VCC = 10V, -VCC = -20V
+VCC = 20V, -VCC = -10V
µV/V
µV/V
µV/V
µV/V
1
-100 +100
-50 +50
2, 3
1
-100 +100
2, 3
Common Mode Rejection Ratio VCC
=
35V to 5V, VCM =
80
dB
mV
mV
mA
mA
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
15V
Adjustment for Input Offset
Voltage
4.0
Adjustment for Input Offset
Voltage
-4.0
-60
+60
Output Short Circuit Current
+VCC = 15V, -VCC = -15V,
t ≤ 25mS, VCM = -15V
-IOS
Output Short Circuit Current
Power Supply Current
+VCC = 15V, -VCC = -15V,
t ≤ 25mS, VCM = +15V
+VCC = 15V, -VCC = -15V
ICC
3.0
2.32
3.5
mA
mA
1
2
3
2
3
2
3
mA
∆VIO/ ∆T
∆ IIO / ∆T
Temperature Coefficient of
Input Offset Voltage
-55˚C ≤ TA ≤ +25˚C
+25˚C ≤ TA ≤ +125˚C
-55˚C ≤ TA ≤ +25˚C
+25˚C ≤ TA ≤ +125˚C
(Note 8)
(Note 8)
(Note 8)
(Note 8)
-18
-15
+18
+15
µV/˚C
uV/˚C
pA/˚C
pA/˚C
Temperature Coefficient of
Input Offset Current
-200 +200
-100 +100
7
www.national.com
LM101A QML & RH Electrical Characteristics (Note 10) (Continued)
DC Parameters (Continued)
The following conditions apply to all parameters, unless otherwise specified
VCC
=
20V, VCM = 0V, RS = 50Ω
Symbol
Parameter
Conditions
Sub-
groups
4
Notes
Min Max
Units
-AVS
Large Signal (Open Loop)
Voltage Gain
RL = 2KΩ, VO = -15V
RL = 10KΩ, VO = -15V
RL = 2KΩ, VO = +15V
RL = 10KΩ, VO = +15V
(Note 9)
(Note 9)
(Note 9)
(Note 9)
(Note 9)
(Note 9)
(Note 9)
(Note 9)
50
25
50
25
50
25
50
25
V/mV
V/mV
V/mV
V/mV
V/mV
V/mV
V/mV
V/mV
5, 6
4
5, 6
4
+AVS
Large Signal (Open Loop)
Voltage Gain
5, 6
4
5, 6
AVS
Large Signal (Open Loop)
Voltage Gain
VCC
=
=
5V,RL = 2KΩ,
2V
5V, RL = 10KΩ,
2V
(Note 9)
(Note 9)
10
10
V/mV
V/mV
4,5, 6
4,5, 6
VO
=
VCC
VO
=
+VOP
-VOP
Output Voltage Swing
Output Voltage Swing
RL = 10KΩ, VCM = -20V
RL = 2KΩ, VCM = -20V
RL = 10KΩ, VCM = 20V
RL = 2KΩ, VCM = 20V
+16
+15
-16
-15
V
V
V
V
4,5, 6
4,5, 6
4,5, 6
4,5, 6
AC Parameters
The following conditions apply to all parameters, unless otherwise specified
VCC
=
20V, VCM = 0V, RS = 50Ω
Symbol
Parameter
Conditions
Sub-
groups
7, 8A
8B
Notes
Min Max
Units
+SR
Slew Rate
Slew Rate
AV = 1, VI = -5V to +5V
AV = 1, VI = +5V to -5V
0.3
0.2
0.3
0.2
800
25
V/µS
V/µS
V/µS
V/µS
nS
-SR
7, 8A
8B
TRTR
TROS
Rise Time
Overshoot
AV = 1, VI = 50mV
AV = 1, VI = 50mV
7, 8A, 8B
7
%
35
%
8A, 8B
7
NIBB
NIPC
Noise Broadband
Noise Popcorn
BW = 10Hz to 5KHz, RS = 0Ω
BW = 10Hz to 5KHz,
RS = 100KΩ
15
µVRMS
80
µVPK
7
DC Parameters Drift Values
The following conditions apply to all parameters, unless otherwise specified
VCC
=
20V, VCM = 0V, RS = 50Ω
Delta calculations performed on QMLV devices at group B, Subgroup 5 only.
Symbol
Parameter
Conditions
Sub-
groups
Notes
Min Max
Units
VIO
IIB
Input Offset Voltage
Input Bias Current
VCM = 0V
-0.5
-7.5
0.5
7.5
mV
nA
1
1
VCM = 0V, RS = 100KΩ
www.national.com
8
Notes
Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device is
intended to be functional, but do no guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The
guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed
test conditions.
Note 3: For supply voltages less than 15V, the absolute maximum input voltage is equal to the supply voltage.
Note 4: The maximum power dissipation must be derated at elevated temperatures and is dictated by T
(maximum junction temperature), θ (package junction
JA
Jmax
to ambient thermal resistance), and T (ambient temperature). The maximum allowable power dissipation at any temperature is P
= (T
− T ) / θ or the
A
Dmax
Jmax A JA
number given in the Absolute Maximum Ratings, whichever is lower.
Note 5: Human body model, 100 pF discharged through 1.5 kΩ.
Note 6: Parameter guaranteed by the input conditions of several DC parameters
Note 7: Parameter guaranteed, not tested.
Note 8: Calculated parameter
Note 9: Datalog reading of K = V/mV.
Note 10: Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics. These parts may be dose rate sensitive in a space
environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters are guaranteed only for the conditions as specified
in Mil-Std-883, Method 1019
Note 11: Pin connections shown are for 8-pin packages.
9
www.national.com
Typical Performance Characteristics LM101A
Input Voltage Range
Output Swing
20122342
20122341
Voltage Gain
20122343
Supply Current
Voltage Gain
20122347
20122348
www.national.com
10
Typical Performance Characteristics LM101A (Continued)
Input Current,
Maximum Power Dissipation
LM101A
20122349
20122350
Current Limiting
Input Noise Voltage
20122351
20122352
Input Noise Current
Common Mode Rejection
20122353
20122354
11
www.national.com
Typical Performance Characteristics LM101A (Continued)
Closed Loop Output
Impedance
Power Supply Rejection
20122355
20122356
www.national.com
12
Typical Performance Characteristics for Various Compensation Circuits
(Note 11)
Single Pole Compensation
Two Pole Compensation
20122308
20122312
C = 30 pF
S
C = 30 pF
S
C2 = 10 C1
Open Loop Frequency
Response
Feedforward Compensation
20122316
20122309
f = 3 MHz
o
Open Loop Frequency
Response
Open Loop Frequency
Response
20122317
20122313
13
www.national.com
Typical Performance Characteristics for Various Compensation Circuits
(Note 11) (Continued)
Large Signal Frequency
Response
Large Signal Frequency
Response
20122310
20122318
20122315
20122314
20122311
20122319
Large Signal Frequency
Response
Voltage Follower Pulse
Response
Voltage Follower Pulse
Response
Inverter Pulse Response
www.national.com
14
Typical Applications (Note 11)
Inverting Amplifier
with Balancing Circuit
Variable Capacitance Multiplier
20122320
20122323
†
May be zero or equal to parallel combination of R1 and R2 for minimum
offset.
Simulated Inductor
Sine Wave Oscillator
20122321
L . R1 R2 C1
R
R
= R2
= R1
S
P
Fast Inverting Amplifier
with High Input Impedance
20122324
f
o
= 10 kHz
Integrator with Bias Current Compensation
20122322
20122325
*Adjust for zero integrator drift. Current drift typically 0.1 nA/˚C over −55˚C
to +125˚C temperature range.
15
www.national.com
Application Hints (Note 11)
Protecting Against Gross
Fault Conditions
20122326
*Protects input
†
‡
Protects output
Protects output — not needed when R4 is used.
Compensating for Stray Input Capacitances
or Large Feedback Resistor
20122327
Isolating Large Capacitive Loads
20122328
www.national.com
16
Although the LM101A is designed for trouble free operation,
experience has indicated that it is wise to observe certain
precautions given below to protect the devices from abnor-
mal operating conditions. It might be pointed out that the
advice given here is applicable to practically any IC op amp,
although the exact reason why may differ with different de-
vices.
Typical Applications (Note 11)
Standard Compensation and
Offset Balancing Circuit
When driving either input from a low-impedance source, a
limiting resistor should be placed in series with the input lead
to limit the peak instantaneous output current of the source
to something less than 100 mA. This is especially important
when the inputs go outside a piece of equipment where they
could accidentally be connected to high voltage sources.
Large capacitors on the input (greater than 0.1 µF) should be
treated as a low source impedance and isolated with a
resistor. Low impedance sources do not cause a problem
unless their output voltage exceeds the supply voltage. How-
ever, the supplies go to zero when they are turned off, so the
isolation is usually needed.
The output circuitry is protected against damage from shorts
to ground. However, when the amplifier output is connected
to a test point, it should be isolated by a limiting resistor, as
test points frequently get shorted to bad places. Further,
when the amplifer drives a load external to the equipment, it
is also advisable to use some sort of limiting resistance to
preclude mishaps.
20122329
Fast Voltage Follower
Precautions should be taken to insure that the power sup-
plies for the integrated circuit never become
reversed—even under transient conditions. With reverse
voltages greater than 1V, the IC will conduct excessive cur-
rent, fusing internal aluminum interconnects. If there is a
possibility of this happening, clamp diodes with a high peak
current rating should be installed on the supply lines. Rever-
sal of the voltage between V+ and V− will always cause a
problem, although reversals with respect to ground may also
give difficulties in many circuits.
The minimum values given for the frequency compensation
capacitor are stable only for source resistances less than
10 kΩ, stray capacitances on the summing junction less than
5 pF and capacitive loads smaller than 100 pF. If any of
these conditions are not met, it becomes necessary to over-
compensate the amplifier with a larger compensation capaci-
tor. Alternately, lead capacitors can be used in the feedback
network to negate the effect of stray capacitance and large
feedback resistors or an RC network can be added to isolate
capacitive loads.
20122331
Power Bandwidth: 15 kHz
Slew Rate: 1V/µs
Fast Summing Amplifier
Although the LM101A is relatively unaffected by supply by-
passing, this cannot be ignored altogether. Generally it is
necessary to bypass the supplies to ground at least once on
every circuit card, and more bypass points may be required
if more than five amplifiers are used. When feed-forward
compensation is employed, however, it is advisable to by-
pass the supply leads of each amplifier with low inductance
capacitors because of the higher frequencies involved.
20122330
Power Bandwidth: 250 kHz
Small Signal Bandwiidth: 3.5 MHz
Slew Rate: 10V/µs
17
www.national.com
Typical Applications (Note 11) (Continued)
Bilateral Current Source
20122332
R3 = R4 + R5
R1 = R2
Fast AC/DC Converter (Note 12)
20122333
Note 12: Feedforward compensation can be used to make a fast full wave rectifier without a filter.
www.national.com
18
Typical Applications (Note 11) (Continued)
Instrumentation Amplifier
20122334
R1 = R4; R2 = R3
†
*, Matching determines CMRR.
Voltage Comparator for Driving RTL Logic or High
Current Driver
Integrator with Bias Current Compensation
20122337
20122335
*Adjust for zero integrator drift. Current drift typically 0.1 nA/˚C over 0˚C to
+70˚C temperature range.
19
www.national.com
Typical Applications (Note 11) (Continued)
Low Frequency Square Wave Generator
20122336
Voltage Comparator for Driving
DTL or TTL Integrated Circuits
Low Drift Sample and Hold
20122339
20122338
*Polycarbonate-dielectric capacitor
www.national.com
20
Revision History Section
Date
Revision
Section
Originator
Changes
Released
01/05/06
A
New Release to corporate format
L. Lytle
2 MDS datasheets converted into one Corp.
datasheet format. MNLM101A-X Rev 0A0
and MRLM101A-X-RH rev 1C2 MDS
datasheets will be archived.
21
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted
Metal Can Package (H)
NS Package Number H08C
Ceramic Dual-In-Line Package (J)
NS Package Number J08A
www.national.com
22
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Ceramic Flatpack Package (W)
NS Package Number W10A
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain
no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
Leadfree products are RoHS compliant.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Medical
Security
Logic
Space, Avionics and Defense www.ti.com/space-avionics-defense
Transportation and Automotive www.ti.com/automotive
Power Mgmt
Microcontrollers
RFID
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
相关型号:
LM101F
Operational Amplifier, 1 Func, 6000uV Offset-Max, CDFP10, HERMETIC SEALED, CERPACK-10
ROCHESTER
©2020 ICPDF网 联系我们和版权申明