LF442MWA [TI]
IC DUAL OP-AMP, 7500 uV OFFSET-MAX, 1 MHz BAND WIDTH, UUC, WAFER, Operational Amplifier;
| 型号： | LF442MWA |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | IC DUAL OP-AMP, 7500 uV OFFSET-MAX, 1 MHz BAND WIDTH, UUC, WAFER, Operational Amplifier |
| 文件： | 总14页 (文件大小：499K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
August 2000
LF442
Dual Low Power JFET Input Operational Amplifier
General Description
Features
n 1/10 supply current of a LM1458: 400 µA (max)
n Low input bias current: 50 pA (max)
n Low input offset voltage: 1 mV (max)
n Low input offset voltage drift: 10 µV/˚C (max)
n High gain bandwidth: 1 MHz
The LF442 dual low power operational amplifiers provide
many of the same AC characteristics as the industry stan-
dard LM1458 while greatly improving the DC characteristics
of the LM1458. The amplifiers have the same bandwidth,
slew rate, and gain (10 kΩ load) as the LM1458 and only
draw one tenth the supply current of the LM1458. In addition
the well matched high voltage JFET input devices of the
LF442 reduce the input bias and offset currents by a factor of
10,000 over the LM1458. A combination of careful layout
design and internal trimming guarantees very low input offset
voltage and voltage drift. The LF442 also has a very low
equivalent input noise voltage for a low power amplifier.
n High slew rate: 1 V/µs
n Low noise voltage for low power:
n Low input noise current:
n High input impedance: 1012
Ω
n High gain VO
=
10V, RL = 10k: 50k (min)
The LF442 is pin compatible with the LM1458 allowing an
immediate 10 times reduction in power drain in many appli-
cations. The LF442 should be used where low power dissi-
pation and good electrical characteristics are the major con-
siderations.
Typical Connection
Connection Diagrams
Metal Can Package
00915502
Pin 4 connected to case
Top View
00915501
Order Number LF442AMH or LF442MH/883
See NS Package Number H08A
Ordering Information
Dual-In-Line Package
LF442XYZ
X indicates electrical grade
Y indicates temperature range
“M” for military
“C” for commercial
Z indicates package type
“H” or “N”
00915504
Top View
Order Number LF442ACN or LF442CN
See NS Package Number N08E
™
BI-FET II is a trademark of National Semiconductor Corporation.
© 2004 National Semiconductor Corporation
DS009155
www.national.com
Absolute Maximum Ratings (Note 1)
H Package
N Package
θJA (Typical)
(Note 4)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
65˚C/W
165˚C/W
21˚C/W
(Note 5)
114˚C/W
152˚C/W
(Note 5)
LF442A
22V
LF442
18V
θJC (Typical)
Supply Voltage
Operating Temperature
Range
(Note 5)
Differential Input Voltage
Input Voltage Range
(Note 2)
38V
30V
19V
15V
Storage
−65˚C≤TA≤150˚C−65˚C≤TA≤150˚C
Temperature Range
Lead Temperature
(Soldering, 10 sec.)
ESD Tolerance
Output Short Circuit
Duration (Note 3)
Continuous Continuous
260˚C
260˚C
Rating to be determined
H Package
150˚C
N Package
Tj max
115˚C
DC Electrical Characteristics (Note 7)
Symbol
Parameter
Conditions
LF442A
LF442
Units
Min
Typ
Max
Min
Typ
Max
5.0
VOS
Input Offset Voltage
RS = 10 kΩ, TA = 25˚C
Over Temperature
RS = 10 kΩ
0.5
1.0
1.0
mV
mV
7.5
∆VOS/∆T Average TC of Input
7
5
10
7
5
µV/˚C
Offset Voltage
IOS
Input Offset Current
VS
=
15V
Tj = 25˚C
Tj = 70˚C
Tj = 125˚C
Tj = 25˚C
Tj = 70˚C
Tj = 125˚C
25
1.5
10
50
3
50
pA
nA
(Notes 7, 8)
1.5
nA
IB
Input Bias Current
VS
=
15V
10
10
100
3
pA
(Notes 7, 8)
nA
20
nA
RIN
Input Resistance
Large Signal Voltage
Gain
Tj = 25˚C
1012
200
1012
200
Ω
AVOL
VS
=
15V, VO
=
10V,
50
25
V/mV
RL = 10 kΩ, TA = 25˚C
Over Temperature
25
12
16
200
13
15
12
11
200
13
V/mV
V
VO
Output Voltage Swing
Input Common-Mode
Voltage Range
VS
=
15V, RL = 10 kΩ
VCM
+18
−17
100
+14
−12
95
V
V
CMRR
PSRR
IS
Common-Mode
Rejection Ratio
Supply Voltage
RS ≤ 10 kΩ
80
80
70
70
dB
(Note 9)
100
300
90
dB
µA
Rejection Ratio
Supply Current
400
400
500
www.national.com
2
AC Electrical Characteristics (Note 7)
Symbol
Parameter
Conditions
LF442A
Typ
LF442
Typ
Units
Min
Max
Min
Max
Amplifier to Amplifier
Coupling
TA = 25˚C, f = 1 Hz-20 kHz
(Input Referred)
−120
−120
dB
SR
Slew Rate
VS
VS
=
=
15V, TA = 25˚C
15V, TA = 25˚C
0.8
0.8
1
1
0.6
0.6
1
1
V/µs
MHz
GBW
en
Gain-Bandwidth Product
Equivalent Input Noise
TA = 25˚C, RS = 100Ω,
35
35
Voltage
f = 1 kHz
in
Equivalent Input Noise
TA = 25˚C, f = 1 kHz
0.01
0.01
Current
Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits.
Note 2: Unless otherwise specified the absolute maximum negative input voltage is equal to the negative power supply voltage.
Note 3: Any of the amplifier outputs can be shorted to ground indefinitely, however, more than one should not be simultaneously shorted as the maximum junction
temperature will be exceeded.
Note 4: The value given is in 400 linear feet/min air flow.
Note 5: The value given is in static air.
Note 6: These devices are available in both the commercial temperature range 0˚C ≤ T ≤ 70˚C and the military temperature range −55˚C ≤ T ≤ 125˚C. The
A
A
temperature range is designated by the position just before the package type in the device number. A “C” indicates the commercial temperature range and an “M”
indicates the military temperature range. The military temperature range is available in “H” package only.
Note 7: Unless otherwise specified, the specifications apply over the full temperature range and for V
=
20V for the LF442A and for V
=
S
15V for the LF442.
S
V
, I , and I
are measured at V
= 0.
OS
B
OS
CM
Note 8: The input bias currents are junction leakage currents which approximately double for every 10˚C increase in the junction temperature, T . Due to limited
j
production test time, the input bias currents measured are correlated to junction temperature. In normal operation the junction temperature rises above the ambient
temperature as a result of internal power dissipation, P . T = T + θ
P
where θ is the thermal resistance from junction to ambient. Use of a heat sink is
D
j
A
jA
D jA
recommended if input bias current is to be kept to a minimum.
Note 9: Supply voltage rejection ratio is measured for both supply magnitudes increasing or decreasing simultaneously in accordance with common practice from
15V to 5V for the LF442 and 20V to 5V for the LF442A.
Note 10: Refer to RETS442X for LF442MH military specifications.
Simplified Schematic
1/2 Dual
00915503
3
www.national.com
Typical Performance Characteristics
Input Bias Current
Input Bias Current
00915518
00915520
00915522
00915517
Positive Common-Mode
Input Voltage Limit
Supply Current
00915519
Negative Common-Mode
Input Voltage Limit
Positive Current Limit
00915521
www.national.com
4
Typical Performance Characteristics (Continued)
Negative Current Limit
Output Voltage Swing
00915523
00915524
Output Voltage Swing
Gain Bandwidth
00915525
00915526
Bode Plot
Slew Rate
00915527
00915528
5
www.national.com
Typical Performance Characteristics (Continued)
Undistorted Output Voltage
Swing
Distortion vs Frequency
00915529
00915530
Open Loop Frequency
Response
Common-Mode Rejection
Ratio
00915531
00915532
Power Supply Rejection
Ratio
Equivalent Input Noise
Voltage
00915534
00915533
www.national.com
6
Typical Performance Characteristics (Continued)
Open Loop Voltage Gain
Output Impedance
00915535
00915536
Inverter Settling Time
00915537
7
www.national.com
Pulse Response RL = 10 kΩ, CL = 10 pF
Large Signal Inverting
Small Signal Inverting
00915509
00915507
Large Signal Non-Inverting
Small Signal Non-Inverting
00915510
00915508
www.national.com
8
The amplifiers will drive a 10 kΩ load resistance to
over the full temperature range.
10V
Application Hints
This device is a dual low power op amp with internally
trimmed input offset voltages and JFET input devices (BI-
FET II). These JFETs have large reverse breakdown volt-
ages from gate to source and drain eliminating the need for
clamps across the inputs. Therefore, large differential input
voltages can easily be accommodated without a large in-
crease in input current. The maximum differential input volt-
age is independent of the supply voltages. However, neither
of the input voltages should be allowed to exceed the nega-
tive supply as this will cause large currents to flow which can
result in a destroyed unit.
Precautions should be taken to ensure that the power supply
for the integrated circuit never becomes reversed in polarity
or that the unit is not inadvertently installed backwards in a
socket as an unlimited current surge through the resulting
forward diode within the IC could cause fusing of the internal
conductors and result in a destroyed unit.
As with most amplifiers, care should be taken with lead
dress, component placement and supply decoupling in order
to ensure stability. For example, resistors from the output to
an input should be placed with the body close to the input to
minimize “pick-up” and maximize the frequency of the feed-
back pole by minimizing the capacitance from the input to
ground.
Exceeding the negative common-mode limit on either input
will force the output to a high state, potentially causing a
reversal of phase to the output. Exceeding the negative
common-mode limit on both inputs will force the amplifier
output to a high state. In neither case does a latch occur
since raising the input back within the common-mode range
again puts the input stage and thus the amplifier in a normal
operating mode.
A feedback pole is created when the feedback around any
amplifier is resistive. The parallel resistance and capacitance
from the input of the device (usually the inverting input) to AC
ground set the frequency of the pole. In many instances the
frequency of this pole is much greater than the expected 3
dB frequency of the closed loop gain and consequenty there
is negligible effect on stability margin. However, if the feed-
back pole is less than approximately 6 times the expected 3
dB frequency a lead capacitor should be placed from the
output to the input of the op amp. The value of the added
capacitor should be such that the RC time constant of this
capacitor and the resistance it parallels is greater than or
equal to the original feedback pole time constant.
Exceeding the positive common-mode limit on a single input
will not change the phase of the output; however, if both
inputs exceed the limit, the output of the amplifier will be
forced to a high state.
The amplifiers will operate with a common-mode input volt-
age equal to the positive supply; however, the gain band-
width and slew rate may be decreased in this condition.
When the negative common-mode voltage swings to within
3V of the negative supply, an increase in input offset voltage
may occur.
Each amplifier is individually biased to allow normal circuit
operation with power supplies of 3.0V. Supply voltages less
than these may degrade the common-mode rejection and
restrict the output voltage swing.
Typical Applications
Battery Powered Strip Chart Preamplifier
00915511
Runs from 9v batteries ( 9V supplies)
Fully settable gain and time constant
Battery powered supply allows direct plug-in interface to strip chart recorder without common-mode problems
9
www.national.com
Typical Applications (Continued)
→
“No FET” Low Power V F Converter
00915512
Trim 1M pot for 1 kHz full-scale output
15 mW power drain
No integrator reset FET required
Mount D1 and D2 in close proximity
1% linearity to 1 kHz
High Efficiency Crystal Oven Controller
00915513
•
•
•
•
•
Tcontrol= 75˚C
A1’s output represents the amplified difference between the LM335 temperature sensor and the crystal oven’s temperature
A2, a free running duty cycle modulator, drives the LM395 to complete a servo loop
Switched mode operation yields high efficiency
1% metal film resistor
www.national.com
10
Typical Applications (Continued)
Conventional Log Amplifier
00915514
R
= Tel Labs type Q81
T
Trim 5k for 10 µA through the 5k–120k combination
*1% film resistor
Unconventional Log Amplifier
00915515
Q1, Q2, Q3 are included on LM389 amplifier chip which is temperature-stabilized by the LM389 and Q2-Q3, which act as a heater-sensor pair.
Q1, the logging transistor, is thus immune to ambient temperature variation and requires no temperature compensation at all.
11
www.national.com
Detailed Schematic
1/2 Dual
00915516
www.national.com
12
Physical Dimensions inches (millimeters)
unless otherwise noted
TO-5 Metal Can Package (H)
Order Number LF442AMH or LF442MH/883
NS Package Number H08A
13
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Molded Dual-In-Line Package (N)
Order Number LF442ACN or LF442CN
NS Package Number N08E
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification
(CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
相关型号：
©2020 ICPDF网 联系我们和版权申明