DS90UR916QSQ/NOPB [TI]
具有图像增强功能的 5MHz 至 65MHz 24 位彩色 FPD-Link II 解串器 | NKB | 60 | -40 to 105;型号: | DS90UR916QSQ/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有图像增强功能的 5MHz 至 65MHz 24 位彩色 FPD-Link II 解串器 | NKB | 60 | -40 to 105 光电二极管 接口集成电路 |
文件: | 总48页 (文件大小:628K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
DS90UR916Q 5 - 65 MHz 24-bit Color FPD-Link II Deserializer with Image Enhancement
Check for Samples: DS90UR916Q
1
FEATURES
DESCRIPTION
The DS90UR916Q FPD-Link II deserializer operates
with the DS90UR905Q FPD-Link II serializer to
2
•
5 – 65 MHz PCLK support (140 Mbps – 1.82
Gbps)
deliver 24-bit digital video data over
a single
•
•
RGB888 + VS, HS, DE Support
differential pair. The DS90UR916Q provides features
designed to enhance image quality at the display.
The high speed serial bus scheme of FPD-Link II
greatly eases system design by eliminating skew
problems between clock and data, reduces the
number of connector pins, reduces the interconnect
size, weight, and cost, and overall eases PCB layout.
In addition, internal DC balanced decoding is used to
support AC-coupled interconnects.
Image Enhancement - White Balance LUTs and
Adaptive Hi-FRC Dithering
•
AC Coupled STP Interconnect Cable up to 10
Meters
•
•
•
@ Speed Link BIST Mode and Reporting Pin
I2C Compatible Serial Control Bus
Power Down Mode Minimizes Power
Dissipation
The DS90UR916Q Des (deserializer) recovers the
data (RGB) and control signals and extracts the clock
from the serial stream. The Des locks to the incoming
serial data stream without the use of a training
sequence or special SYNC patterns, and does not
require a reference clock. A link status (LOCK) output
signal is provided. The DS90UR916Q is ideally suited
for 24-bit color applications. White balance lookup
tables and adaptive Hi-FRC dithering provide the user
a cost-effective means to enhance display image
quality.
•
•
1.8V or 3.3V Compatible LVCMOS I/O Interface
Automotive Grade Product: AEC-Q100 Grade 2
Qualified
•
•
>8 kV HBM and ISO 10605 ESD Rating
FAST Random Ddata Lock; No Reference
Clock Required
•
•
•
Adjustable Input Receiver Equalization
LOCK (Real Time Link Status) Reporting Pin
EMI Minimization on Output Parallel Bus
(SSCG)
Serial transmission is optimized with user selectable
receiver equalization. EMI is minimized by the use of
low voltage differential signaling, output slew control,
and the Des may be configured to generate Spread
Spectrum Clock and Data on its parallel outputs.
•
•
Output Slew Control (OS)
Backward Compatible Mode for Operation with
Older Generation Devices
The DS90UR916Qis offered in a 60-pin WQFN
package. It is specified over the automotive AEC-
Q100 grade 2 temperature range of -40°C to +105°C.
APPLICATIONS
•
•
Automotive Display for Navigation
Automotive Display for Entertainment
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011–2013, Texas Instruments Incorporated
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
Applications Diagram
V
V
DDIO
DDn
V
V
DDIO
(1.8Vor3.3V)
DDn
1.8V (1.8Vor3.3V)
1.8V
FPD-Link II
1 Pair / AC Coupled
R[7:0]
G[7:0]
R[7:0]
G[7:0]
RGB Display
QVGA to XGA
24-bit or
18-bit dithered
color depth
B[7:0]
B[7:0]
HS
VS
DE
PCLK
100 nF
100 nF
HOST
Graphics
Processor
HS
DOUT+
DOUT-
RIN+
RIN-
VS
DE
PCLK
100 ohm STP Cable
CMF
PDB
DS90UR905Q
Serializer
DS90UR916Q
Deserializer
LOCK
PASS
PDB
CONFIG [1:0]
RFB
BISTEN
BISTEN
STRAP pins
not shown
VODSEL
DeEmph
SCL
SDA
ID[x]
SCL
SDA
ID[x]
Optional
Optional
DAP
DAP
Figure 1.
Block Diagrams
STRAP INPUT
SSCG
CONFIG [1:0]
LF_MODE
OS_PCLK/DATA
OSS_SEL
CMF
24
RGB [7:0]
RFB
HS
VS
DE
EQ [3:0]
OSC_SEL [2:0]
SSC [3:0]
RIN+
RIN-
MAPSEL [1:0]
STRAP INPUT
OP_LOW
Error
Detector
PASS
BISTEN
PDB
SCL
SCA
ID[x]
Clock and
Data
Recovery
PCLK
LOCK
Timing and
Control
DS90UR916Q œ DESERIALIZER
Figure 2.
2
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
DS90UR916Q Pin Diagram
NC
RES
NC
46
47
48
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
VDDL
VDDIR
RIN+
G[0]/OSC_SEL[0]
G[1]/OSC_SEL[1]
G[2]/OSC_SEL[2]
G[3]
49
50
51
52
53
54
55
56
57
58
59
60
RIN-
CMF
CMLOUTP
CMLOUTN
VDDCMLO
VDDR
VDDIO
DS90UR916Q
TOP VIEW
G[4]/EQ[0]
G[5]/EQ[1]
G[6]/EQ[2]
G[7]/EQ[3]
B[0]
DAP = GND
ID[x]
BOLD PIN NAME œ indicates I/O strap
VDDPR
VDDSC
PDB
pin associated with output pin
B[1]/RFB
B[2]/OSS_SEL
NC
NC
Figure 3. Deserializer - DS90UR916Q — Top View
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
DS90UR916Q Deserializer Pin Descriptions(1)
Pin Name
Pin #
I/O, Type
Description
LVCMOS Parallel Interface
R[7:0]
G[7:0]
B[7:0]
HS
33, 34, 35,
I, STRAP,
RED Parallel Interface Data Output Pins (MSB = 7, LSB = 0)
36, 37, 39, O, LVCMOS In power-down (PDB = 0), outputs are controlled by the OSS_SEL (See Table 5). These pins
40, 41
are inputs during power-up (See STRAP Inputs).
20, 21, 22,
I, STRAP,
GREEN Parallel Interface Data Output Pins (MSB = 7, LSB = 0)
23, 25, 26, O, LVCMOS In power-down (PDB = 0), outputs are controlled by the OSS_SEL (See Table 5). These pins
27, 28
are inputs during power-up (See STRAP Inputs).
9, 10, 11,
I, STRAP,
BLUE Parallel Interface Data Output Pins (MSB = 7, LSB = 0)
12, 14, 17, O, LVCMOS In power-down (PDB = 0), outputs are controlled by the OSS_SEL (See Table 5). These pins
18, 19
are inputs during power-up (See STRAP Inputs).
8
O, LVCMOS Horizontal Sync Output
In power-down (PDB = 0), output is controlled by the OSS_SEL pin (See Table 5). Video
control signal pulse width must be 3 PCLKs or longer to be transmitted when the Control
Signal Filter is enabled (CONFIG[1:0] = 01). There is no restriction on the minimum transition
pulse when the Control Signal Filter is disabled (CONFIG[1:0] = 00). The signal is limited to 2
transitions per 130 PCLKs.
VS
DE
7
6
O, LVCMOS Vertical Sync Output
In power-down (PDB = 0), output is controlled by the OSS_SEL pin (See Table 5). Video
control signal is limited to 1 transition per 130 PCLKs. Thus, the minimum pulse width is 130
PCLKs.
O, LVCMOS Data Enable Output
In power-down (PDB = 0), output is controlled by the OSS_SEL pin (See Table 5). Video
control signal pulse width must be 3 PCLKs or longer to be transmitted when the Control
Signal Filter is enabled (CONFIG[1:0] = 01). There is no restriction on the minimum transition
pulse when the Control Signal Filter is disabled (CONFIG[1:0] = 00). The signal is limited to 2
transitions per 130 PCLKs.
PCLK
LOCK
5
O, LVCMOS Pixel Clock Output
In power-down (PDB = 0), output is controlled by the OSS_SEL pin (See Table 5). Strobe
edge set by RFB function.
32
O, LVCMOS LOCK Status Output
LOCK = 1, PLL is Locked, outputs are active LOCK = 0, PLL is unlocked, RGB[7:0], HS, VS,
DE and PCLK output states are controlled by OSS_SEL (See Table 5). May be used as Link
Status or to flag when Video Data is active (ON/OFF).
PASS
42
O, LVCMOS PASS Output (BIST Mode)
PASS = 1, error free transmission
PASS = 0, one or more errors were detected in the received payload
Route to test point for monitoring, or leave open if unused.
Control and Configuration — STRAP PINS
For a High State, use a 10 kΩ pull up to VDDIO; for a Low State, the IO includes an internal pull down. The STRAP pins are read upon
power-up and set device configuration. Pin Number listed along with shared RGB Output name in square brackets.
CONFIG[1:0]
10 [B6],
9 [B7]
STRAP
Operating Modes — Pin or Register Control
I, LVCMOS These pins determine the DS90UR916’s operating mode and interfacing device.
w/ pull-down CONFIG[1:0] = 00: Interfacing to DS90UR905, Control Signal Filter DISABLED
CONFIG[1:0] = 01: Interfacing to DS90UR905, Control Signal Filter ENABLED
CONFIG[1:0] = 10: Interfacing to DS90UR241
CONFIG[1:0] = 11: Interfacing to DS90C241
LF_MODE
12 [B4]
STRAP
SSCG Low Frequency Mode — Pin or Register Control
I, LVCMOS Only required when SSCG is enabled, otherwise LF_MODE condition is a DON’T CARE (X).
w/ pull-down LF_MODE = 1, SSCG in low frequency mode (PCLK = 5-20 MHz)
LF_MODE = 0, SSCG in high frequency mode (PCLK = 20-65 MHz)
OS_PCLK
OS_DATA
11 [B5]
14 [B3]
STRAP
PCLK Output Slew Select — Pin or Register Control
I, LVCMOS OS_PCLK = 1, increased PCLK slew
w/ pull-down OS_PCLK = 0, normal (default)
STRAP
Data Output Slew Select — Pin or Register Control
I, LVCMOS OS_DATA = 1, increased DATA slew
w/ pull-down OS_DATA = 0, normal (default)
(1) 1 = HIGH, 0 = LOW.
Submit Documentation Feedback
4
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
DS90UR916Q Deserializer Pin Descriptions(1) (continued)
Pin Name
Pin #
I/O, Type
Description
OP_LOW
42 PASS
STRAP
Outputs held Low when LOCK = 1 — Pin or Register Control
I, LVCMOS NOTE: IT IS NOT RECOMMENDED TO USE ANY OTHER STRAP OPTIONS WITH THIS
w/ pull-down STRAP FUNCTION
OP_LOW = 1: all outputs are held LOW during power up until released by programming
OP_LOW release/set register HIGH
NOTE: Before the device is powered up, the outputs are in tri-state.
See Figure 23 and Figure 24.
OP_LOW = 0: all outputs toggle normally as soon as LOCK goes HIGH (default).
OSS_SEL
17 [B2]
18 [B1]
STRAP
Output Sleep State Select — Pin or Register Control
I, LVCMOS NOTE: OSS_SEL STRAP CANNOT BE USED IF OP_LOW =1
w/ pull-down OSS_SEL is used in conjunction with PDB to determine the state of the outputs when
inactive. (See Table 5).
RFB
STRAP
Pixel Clock Output Strobe Edge Select — Pin or Register Control
I, LVCMOS RFB = 1, parallel interface data and control signals are strobed on the rising clock edge.
w/ pull-down RFB = 0, parallel interface data and control signals are strobed on the falling clock edge.
EQ[3:0]
20 [G7],
21 [G6],
22 [G5],
23 [G4]
STRAP
I, LVCMOS (See Table 2).
w/ pull-down
Receiver Input Equalization — Pin or Register Control
OSC_SEL[2:0]
SSC[3:0]
26 [G2],
27 [G1],
28 [G0]
STRAP
Oscillator Select — Pin or Register Control
I, LVCMOS (See Table 6 and Table 7).
w/ pull-down
34 [R6],
35 [R5],
36 [R4],
37 R[3]
STRAP
Spread Spectrum Clock Generation (SSCG) Range Select — Pin or Register Control
I, LVCMOS (See Table 3 and Table 4).
w/ pull-down
MAP_SEL[1:0]
40 [R1],
41 [R0]
STRAP
Bit Mapping Backward Compatibility / DS90UR241 Options — Pin or Register Control
I, LVCMOS Normal setting to b'00. See (Table 8).
w/ pull-down
Control and Configuration
PDB
59
I, LVCMOS Power Down Mode Input
w/ pull-down PDB = 1, Des is enabled (normal operation).
Refer to POWER UP REQUIREMENTS AND PDB PIN in the Applications Information
Section.
PDB = 0, Des is in power-down.
When the Des is in the power-down state, the LVCMOS output state is determined by
Table 5. Control Registers are RESET.
ID[x]
56
3
I, Analog
Serial Control Bus Device ID Address Select — Optional
Resistor to Ground and 10 kΩ pull-up to 1.8V rail. (See Table 9).
SCL
I, LVCMOS Serial Control Bus Clock Input - Optional
SCL requires an external pull-up resistor to VDDIO
.
SDA
2
I/O, LVCMOS Serial Control Bus Data Input / Output - Optional
Open Drain SDA requires an external pull-up resistor to VDDIO
.
BISTEN
44
I, LVCMOS BIST Enable Input — Optional
w/ pull-down BISTEN = 1, BIST is enabled
BISTEN = 0, BIST is disabled
RES
NC
47
I, LVCMOS Reserved - tie LOW
w/ pull-down
1, 15, 16,
30, 31, 45,
46, 60
Not Connected
Leave pin open (float)
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
DS90UR916Q Deserializer Pin Descriptions(1) (continued)
Pin Name
Pin #
I/O, Type
Description
FPD-Link II Serial Interface
RIN+
RIN-
CMF
49
50
51
I, LVDS
I, LVDS
I, Analog
True Input. The input must be AC Coupled with a 100 nF capacitor.
Inverting Input. The input must be AC Coupled with a 100 nF capacitor.
Common-Mode Filter
VCM center-tap is a virtual ground which may be ac-coupled to ground to increase receiver
common mode noise immunity. Recommended value is 4.7 μF or higher.
CMLOUTP
CMLOUTN
52
53
O, LVDS
O, LVDS
Test Monitor Pin — EQ Waveform
NC or connect to test point. Requires Serial Bus Control to enable.
Test Monitor Pin — EQ Waveform
NC or connect to test point. Requires Serial Bus Control to enable.
Power and Ground(2)
VDDL
29
Power
Power
Power
Power
Power
Power
Power
Ground
Logic Power, 1.8 V ±5%
VDDIR
VDDR
48
43, 55
4, 58
57
Input Power, 1.8 V ±5%
RX High Speed Logic Power, 1.8 V ±5%
SSCG Power, 1.8 V ±5%
VDDSC
VDDPR
VDDCMLO
VDDIO
GND
PLL Power, 1.8 V ±5%
54
RX High Speed Logic Power, 1.8 V ±5%
13, 24, 38
DAP
LVCMOS I/O Power, 1.8 V ±5% OR 3.3 V ±10% (VDDIO)
DAP is the large metal contact at the bottom side, located at the center of the WQFN
package. Connected to the ground plane (GND) with at least 9 vias.
(2) The VDD (VDDn and VDDIO) supply ramp should be faster than 1.5 ms with a monotonic rise. If slower then 1.5 ms then a capacitor on
the PDB pin is needed to ensure PDB arrives after all the VDD have settled to the recommended operating voltage.
6
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)
Supply Voltage – VDDn (1.8V)
Supply Voltage – VDDIO
LVCMOS I/O Voltage
Receiver Input Voltage
Junction Temperature
Storage Temperature
60L WQFN Package
−0.3V to +2.5V
−0.3V to +4.0V
−0.3V to +(VDDIO + 0.3V)
−0.3V to (VDD + 0.3V)
+150°C
−65°C to +150°C
470mW
Maximum Power Dissipation Capacity at
25°C 470mW
Derate above 25C
1/θJA mW / °C
24.6 °C/W
2.8 °C/W
≥±8 kV
θJA(based on 9 thermal vias)
θJC(based on 9 thermal vias)
ESD Rating (HBM)
ESD Rating (CDM)
ESD Rating (MM)
≥±1 kV
≥±250 V
ESD Rating (ISO10605), RD = 2kΩ, CS = 150pF or RD = 2kΩ, CS = 330pF or RD = 330Ω, CS = 150pF
Air Discharge (RIN+, RIN−
Contact Discharge (RIN+, RIN−
ESD Rating (ISO10605), RD = 330Ω, CS = 330pF
Air Discharge (RIN+, RIN−
Contact Discharge (RIN+, RIN−
ESD Rating (IEC 61000–4–2), RD = 330Ω, CS = 150pF
Air Discharge (RIN+, RIN−
Contact Discharge (RIN+, RIN−
For soldering specifications see product folder at www.ti.com and SNOA549
)
≥±30 kV
≥±10 kV
)
)
≥±15 kV
≥±10 kV
)
)
≥±25 kV
≥±10 kV
)
(1) “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of
device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or
other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating
Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
Recommended Operating Conditions
Min
1.71
1.71
Nom
1.8
Max
1.89
1.89
Units
Supply Voltage (VDDn
)
V
V
LVCMOS Supply Voltage (VDDIO
OR
)
)
1.8
LVCMOS Supply Voltage (VDDIO
3.0
−40
5
3.3
3.6
+105
65
V
Operating Free Air Temperature (TA)
PCLK Clock Frequency
Supply Noise(1)
+25
°C
MHz
mVP-P
50
(1) Supply noise testing was done with minimum capacitors on the PCB. A sinusoidal signal is AC coupled to the VDDn (1.8V) supply with
amplitude = 100 mVp-p measured at the device VDDn pins. Bit error rate testing of input to the Ser and output of the Des with 10 meter
cable shows no error when the noise frequency on the Ser is less than 750 kHz. The Des on the other hand shows no error when the
noise frequency is less than 400 kHz.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
Deserializer DC Electrical Characteristics(1)(2)(3)
Over recommended operating supply and temperature ranges unless otherwise specified.
Symb
ol
Parameter
Conditions
Pin/Freq.
Units
Min
Typ
Max
3.3 V I/O LVCMOS DC SPECIFICATIONS – VDDIO = 3.0 to 3.6V
VIH
VIL
IIN
High Level Input Voltage
Low Level Input Voltage
Input Current
2.2
GND
−15
VDDIO
0.8
V
V
PDB, BISTEN
VIN = 0V or VDDIO
±1
+15
μA
R[7:0], G[7:0],
B[7:0], HS, VS,
DE, PCLK, LOCK,
PASS
High Level Output
Voltage
VOH
IOH = −2 mA, OS_PCLK/DATA = L
2.4
VDDIO
V
V
R[7:0], G[7:0],
B[7:0], HS, VS,
DE, PCLK, LOCK,
PASS
Low Level Output
Voltage
VOL
IOL = +2 mA, OS_PCLK/DATA = L
GND
0.4
Output Short Circuit
Current
VDDIO = 3.3V
VOUT = 0V, OS_PCLK/DATA = L/H
PCLK
36
37
mA
mA
µA
IOS
VDDIO = 3.3V
VOUT = 0V
OS_PCLK/DATA = L/H
Output Short Circuit
Current
Des Outputs
Outputs
TRI-STATE® Output
Current
PDB = 0V, OSS_SEL = 0V,
VOUT = 0V or VDDIO
IOZ
−15
+15
1.8 V I/O LVCMOS DC SPECIFICATIONS – VDDIO = 1.71 to 1.89V
VIH
VIL
IIN
High Level Input Voltage
Low Level Input Voltage
Input Current
1.235
GND
−15
VDDIO
0.595
+15
V
V
PDB, BISTEN
VIN = 0V or VDDIO
±1
μA
High Level Output
Voltage
VDDIO
− 0.45
R[7:0], G[7:0],
B[7:0], HS, VS,
DE, PCLK, LOCK,
PASS
VOH
VOL
IOH = −2 mA, OS_PCLK/DATA = L
VDDIO
V
V
Low Level Output
Voltage
IOL = +2 mA, OS_PCLK/DATA = L
GND
0.45
VDDIO = 1.8V
VOUT = 0V
OS_PCLK/DATA = L/H
Output Short Circuit
Current
PCLK
18
18
mA
mA
IOS
VDDIO = 1.8V
VOUT = 0V
OS_PCLK/DATA = L/H
Output Short Circuit
Current
Des Outputs
Outputs
TRI-STATE® Output
Current
PDB = 0V, OSS_SEL = 0V,
VOUT = 0V or VDDIO
IOZ
-15
+50
−50
+15
µA
mV
mV
Differential Input
Threshold High Voltage
VTH
VTL
VCM = +1.2V (Internal VBIAS
)
Differential Input
Threshold Low Voltage
Common Mode Voltage,
Internal VBIAS
RIN+, RIN-
VCM
IIN
1.2
V
µA
Ω
Input Current
VIN = 0V or VDDIO
-15
80
+15
120
Internal Termination
Resistor
RT
100
(1) Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground
except VOD, ΔVOD, VTH and VTL which are differential voltages.
(2) Typical values represent most likely parametric norms at VDD = 3.3V, Ta = +25 degC, and at the Recommended Operation Conditions at
the time of product characterization and are not ensured.
(3) The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as
otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and
are not ensured.
8
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
Deserializer DC Electrical Characteristics(1)(2)(3) (continued)
Over recommended operating supply and temperature ranges unless otherwise specified.
Symb
ol
Parameter
Conditions
Pin/Freq.
Units
Min
Typ
Max
CML DRIVER OUTPUT DC SPECIFICATIONS – EQ TEST PORT
Differential Output
Voltage
VOD
VOS
RT
RL = 100Ω
RL = 100Ω
542
1.4
mV
V
Offset Voltage
Single-ended
CMLOUTP,
CMLOUTN
Internal Termination
Resistor
80
100
120
Ω
SUPPLY CURRENT
IDD1
Checker Board Pattern,
OS_PCLK/DATA = H,
EQ = 001,
SSCG=ON,CMLOUTP/N
enabled
VDD= 1.89V
VDDIO=1.89V
All VDD pins
93
33
110
45
mA
mA
Deserializer
Supply Current
(includes load current)
IDDIO1
VDDIO
VDDIO = 3.6V
62
75
mA
CL = 4pF, Figure 4
VDD= 1.89V
VDDIO=1.89V
VDDIO = 3.6V
All VDD pins
VDDIO
40
5
3000
50
µA
µA
µA
IDDZ
Deserializer Supply
Current Power Down
PDB = 0V, All other
LVCMOS Inputs = 0V
IDDIOZ
10
100
Deserializer Switching Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
tRCP
Parameter
PCLK Output Period
PCLK Output Duty Cycle
Conditions
Pin/Freq.
Min
Typ
Max
200
57
Units
ns
PCLK
PCLK
15.38
43
T
tRDC
SSCG=OFF, 5–65MHz
SSCG=ON, 5–20MHz
SSCG=ON, 20–65MHz
50
59
53
%
35
65
%
40
60
%
tCLH
LVCMOS
Low-to-High
Transition Time, Figure 5
VDDIO = 1.8V
CL = 4 pF (lumped load)
PCLK/RGB[7:0], HS, VS,
DE
2.1
2.0
1.6
1.5
ns
ns
ns
ns
VDDIO = 3.3V
CL = 4 pF (lumped load)
tCHL
LVCMOS
High-to-Low
Transition Time, Figure 5
VDDIO = 1.8V
CL = 4 pF (lumped load)
PCLK/RGB[7:0], HS, VS,
DE
VDDIO = 3.3V
CL = 4 pF (lumped load)
tROS
Data Valid before PCLK – Set
Up Time, Figure 9
VDDIO = 1.71 to 1.89V or
3.0 to 3.6V
CL = 4 pF (lumped load)
RGB[7:0], HS, VS, DE
RGB[7:0], HS, VS, DE
0.27
0.45
0.55
T
T
tROH
Data Valid after PCLK – Hold
Time, Figure 9
VDDIO = 1.71 to 1.89V or
3.0 to 3.6V
0.4
6
CL = 4 pF (lumped load)
tHBLANK Horizontal Blanking Time
HS
tRCP
ms
ms
ms
ms
ns
tDDLT
Deserializer Lock Time,
Figure 8
SSC[3:0] = 0000 (OFF)(1)
SSC[3:0] = 0000 (OFF)(1)
SSC[3:0] = ON(1)
PCLK = 5 MHz
PCLK = 65MHz
PCLK = 5MHz
PCLK = 65MHz
3
4
30
SSC[3:0] = ON(1)
6
tDD
Des Delay - Latency, Figure 6
Des Period Jitter
139*T
975
500
550
140*T
1700
1000
1250
(2)
tDPJ
SSC[3:0] = OFF(3)(4)
PCLK = 5 MHz
PCLK = 10 MHz
PCLK = 65 MHz
ps
ps
ps
(1) tPLD and tDDLT is the time required by the serializer and deserializer to obtain lock when exiting power-down state with an active PCLK.
(2) Specification is ensured by design and is not tested in production.
(3) tDPJ is the maximum amount the period is allowed to deviate over many samples.
(4) Specification is ensured by characterization and is not tested in production.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
Deserializer Switching Characteristics (continued)
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
SSC[3:0] = OFF(4)(5)
Pin/Freq.
PCLK = 5 MHz
Min
Typ
675
375
500
0.9
Max
Units
ps
(2)
tDCCJ
Des Cycle-to-Cycle Jitter
1150
900
PCLK = 10 MHz
ps
PCLK = 65 MHz
1150
ps
UI(6)
tRJIT
Des Input Jitter Tolerance,
Figure 11
EQ = OFF,
SSCG = OFF,
PCLK = 65MHz
for jitter freq < 2MHz
for jitter freq > 6MHz
0.5
UI
ns
BIST Mode
tPASS BIST PASS Valid Time,
BISTEN = 1, Figure 12
SSCG Mode
1
10
fDEV
Spread Spectrum Clocking
Deviation Frequency
PCLK = 5 to 65 MHz,
SSC[3:0] = ON
±0.5
8
±2
%
fMOD
Spread Spectrum Clocking
Modulation Frequency
PCLK = 5 to 65 MHz,
SSC[3:0] = ON
100
kHz
(5) tDCCJ is the maximum amount of jitter between adjacent clock cycles.
(6) UI – Unit Interval is equivalent to one serialized data bit width (1UI = 1 / 28*PCLK). The UI scales with PCLK frequency.
10
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
Recommended Timing for the Serial Control Bus
Over +3.3V supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
Min
>0
Typ
Max
100
400
Units
kHz
kHz
us
fSCL
SCL Clock Frequency
Standard Mode
Fast Mode
>0
tLOW
SCL Low Period
SCL High Period
Standard Mode
Fast Mode
4.7
1.3
4.0
0.6
4.0
us
tHIGH
Standard Mode
Fast Mode
us
us
tHD;STA Hold time for a start or a
repeated start condition,
Figure 13
Standard Mode
Fast Mode
us
0.6
4.7
0.6
us
us
us
tSU:STA Set Up time for a start or a
repeated start condition,
Figure 13
Standard Mode
Fast Mode
tHD;DAT Data Hold Time, Figure 13
Standard Mode
Fast Mode
0
3.45
0.9
us
us
ns
ns
us
us
us
us
ns
ns
ns
ns
0
tSU;DAT Data Set Up Time, Figure 13
Standard Mode
Fast Mode
250
100
4.0
0.6
4.7
1.3
tSU;STO Set Up Time for STOP
Condition, Figure 13
Standard Mode
Fast Mode
tBUF
Bus Free Time Between STOP Standard Mode
and START, Figure 13
Fast Mode
tr
SCL & SDA Rise Time,
Figure 13
Standard Mode
Fast Mode
1000
300
300
300
tf
SCL & SDA Fall Time,
Figure 13
Standard Mode
Fast mode
DC and AC Serial Control Bus Characteristics
Over 3.3V supply and temperature ranges unless otherwise specified.
Symbol
VIH
VIL
Parameter
Input High Level
Conditions
Min
2.2
Typ
Max
VDDIO
0.8
Units
V
SDA and SCL
SDA and SCL
Input Low Level Voltage
Input Hysteresis
GND
V
VHY
VOL
Iin
>50
mV
V
SDA, IOL = 1.25mA
0
0.4
SDA or SCL, Vin = VDDIO or GND
-15
+15
µA
ns
ns
ns
ns
ns
pF
tR
SDA RiseTime – READ
SDA Fall Time – READ
SDA, RPU = X, Cb ≤ 400pF
40
25
tF
tSU;DAT Set Up Time — READ
tHD;DAT Hold Up Time — READ
520
55
tSP
Cin
Input Filter
50
Input Capacitance
SDA or SCL
<5
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
AC Timing Diagrams and Test Circuits
V
DDIO
PCLK
w/ RFB = L
GND
V
DDIO
RGB[n] (odd),
VS, HS
GND
V
DDIO
RGB[n] (even),
DE
GND
Figure 4. Checkerboard Data Pattern
V
DDIO
80%
20%
GND
t
t
CHL
CLH
Figure 5. Deserializer LVCMOS Transition Times
START
BIT
STOP START
BIT BIT
STOP
BIT
RIN
0
1
2
23
0
1
2
23
(Diff.)
SYMBOL N
SYMBOL N+1
t
DD
PCLK
(RFB = L)
RGB[7:0],
SYMBOL N-2
SYMBOL N-1
SYMBOL N
HS, VS, DE
Figure 6. Deserializer Delay – Latency
1/2 V
DDIO
PDB
RIN
(Diff.)
active
"X"
t
XZR
PCLK,
RGB[7:0],
DE, HS, VS,
PASS, LOCK
active
Z (TRI-STATE)
Figure 7. Deserializer Disable Time (OSS_SEL = 0)
12
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
2.0V
PDB
0.8V
RIN
(Diff.)
Don‘t Care
t
DDLT
TRI-STATE
or LOW
LOCK
Z or L
t
RxZ
RGB[7:0],
HS, VS, DE
TRI-STATE or LOW or Pulled Up
Z or L or PU
PCLK
(RFB = L)
TRI-STATE or LOW
IN LOCK TIME
Z or L
OFF
OFF
ACTIVE
Figure 8. Deserializer PLL Lock Times and PDB TRI-STATE Delay(1)
Note: (1) When the Serializer output is at TRI-STATE the Deserializer will lose PLL lock. Resynchronization / Relock must occur before data transfer require
tPLD
V
DDIO
PCLK
w/ RFB = H
1/2 V
DDIO
GND
V
DDIO
RGB[n],
VS, HS, DE
1/2 V
DDIO
GND
t
t
ROH
ROS
Figure 9. Deserializer Output Data Valid (Setup and Hold) Times with SSCG = Off
V
DDIO
PCLK
w/ RFB = H
1/2 V
DDIO
GND
RGB[n],
VS, HS, DE
1/2 V
DDIO
1/2 V
V
DDIO
DDIO
GND
t
t
ROH
ROS
Figure 10. Deserializer Output Data Valid (Setup and Hold) Times with SSCG = On
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
Ideal Data
Bit End
Sampling
Window
Ideal Data Bit
Beginning
V
TH
0V
RxIN_TOL
Left
RxIN_TOL
Right
V
TL
Ideal Center Position (t /2)
BIT
t
(1 UI)
BIT
t
RJIT = RxIN_TOL (Left + Right)
Sampling Window = 1 UI - t
RJIT
Figure 11. Receiver Input Jitter Tolerance
BISTEN
1/2 V
DDIO
tPASS
PASS
(w/ errors)
1/2 V
DDIO
Prior BIST Result
Current BIST Test - Toggle on Error
Result Held
Figure 12. BIST PASS Waveform
SDA
SCL
t
BUF
t
t
LOW
t
f
t
r
HD;STA
t
t
SP
t
f
r
t
t
SU;STA
t
HD;STA
SU;STO
t
HIGH
t
t
SU;DAT
HD;DAT
STOP START
START
REPEATED
START
Figure 13. Serial Control Bus Timing Diagram
14
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
FUNCTIONAL DESCRIPTION
The DS90UR905 / DS90UR916Q chipset transmits and receives 27-bits of data (24-high speed color bits and 3
low speed video control signals) over a single serial FPD-Link II pair operating at 140Mbps to 1.82Gbps. The
serial stream also contains an embedded clock, video control signals and the DC-balance information which
enhances signal quality and supports AC coupling. The pair is intended for use with each other but is backward
compatible with previous generations of FPD-Link II as well.
The Des can attain lock to a data stream without the use of a separate reference clock source, which greatly
simplifies system complexity and overall cost. The Des also synchronizes to the Ser regardless of the data
pattern, delivering true automatic “plug and lock” performance. It can lock to the incoming serial stream without
the need of special training patterns or sync characters. The Des recovers the clock and data by extracting the
embedded clock information, validating and then deserializing the incoming data stream providing a parallel
LVCMOS video bus to the display. White balance LUTs and dithering features are provided to enable display
image enhancement.
The DS90UR905 / DS90UR916Q chipset can operate in 24-bit color depth (with VS,HS,DE encoded in the DCA
bit) or in 18-bit color depth (with VS, HS, DE encoded in DCA or mapped into the high-speed data bits). In 18–bit
color applications, the three video signals maybe sent encoded via the DCA bit (restrictions apply) or sent as
“data bits” along with three additional general purpose signals.
Data Transfer
The DS90UR905 / DS90UR916Q chipset will transmit and receive a pixel of data in the following format: C1 and
C0 represent the embedded clock in the serial stream. C1 is always HIGH and C0 is always LOW. b[23:0]
contain the scrambled RGB data. DCB is the DC-Balanced control bit. DCB is used to minimize the short and
long-term DC bias on the signal lines. This bit determines if the data is unmodified or inverted. DCA is used to
validate data integrity in the embedded data stream and can also contain encoded control (VS,HS,DE). Both
DCA and DCB coding schemes are generated by the Ser and decoded by the Des automatically. Figure 14
illustrates the serial stream per PCLK cycle.
b
1
0
b
1
1
D
C
A
b
0
b
1
b
2
b
3
b
5
b
9
C
1
b
4
b
6
b
7
b
8
D
C
B
b
1
2
b
1
3
b
1
4
b
1
5
b
1
6
b
1
7
b
1
8
b
1
9
b
2
0
b
2
1
b
2
2
b
2
3
C
0
Figure 14. FPD-Link II Serial Stream (905/916)
Des OPERATING MODES AND BACKWARD COMPATIBILITY (CONFIG[1:0])
The DS90UR916Q is also backward compatible with previous generations of FPD-Link II. Configuration modes
are provided for backwards compatibility with the DS90C124 FPD-Link II Generation 1, and also the DS90UR124
FPD-Link II Generation 2 chipset by setting the respective mode with the CONFIG[1:0] pins or control register as
shown in Table 1. The selection also determines whether the Video Control Signal filter feature is enabled or
disabled in Normal mode.
When the DS90UR916 deserializer is configured to operate in backward compatible modes the image
enhancement features (white balance and FRC dithering) are not available.
Table 1. DS90UR916Q Des Modes
CONFIG1
CONFIG0
Mode
Des Device
DS90UR905
DS90UR905
DS90UR241
DS90C241
L
L
L
H
L
Normal Mode, Control Signal Filter disabled
Normal Mode, Control Signal Filter enabled
Backwards Compatible GEN2
Backwards Compatible GEN1
H
H
H
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
Video Control Signal Filter
When operating the devices in Normal Mode, the Video Control Signals (DE, HS, VS) have the following
restrictions:
•
•
•
Normal Mode with Control Signal Filter Enabled:
–
DE and HS — Only 2 transitions per 130 clock cycles are transmitted, the transition pulse must be 3
PCLK or longer.
Normal Mode with Control Signal Filter Disabled:
–
DE and HS — Only 2 transitions per 130 clock cycles are transmitted, no restriction on minimum transition
pulse.
VS — Only 1 transition per 130 clock cycles are transmitted, minimum pulse width is 130 clock cycles.
Video Control Signals are defined as low frequency signals with limited transitions. Glitches of a control signal
can cause a visual display error. This feature allows for the chipset to validate and filter out any high frequency
noise on the control signals. See Figure 15.
PCLK
IN
HS/VS/DE
IN
Latency
PCLK
OUT
Pulses 1 or 2
PCLKs wide
Filetered OUT
HS/VS/DE
OUT
Figure 15. Video Control Signal Filter Waveform
DESERIALIZER Functional Description
The Des converts a single input serial data stream to a wide parallel output bus, and also provides a signal
check for the chipset Built In Self Test (BIST) mode. Several image enhancement features are provided (Note
that these features are not available when operating in backward compatible modes). White balance LUTs allow
the user to define and target the color temperature of the display. Adaptive Hi-FRC dithering enables the
presentation of “true-color” images on an 18–bit color display. The device can be configured via external pins and
strap pins or through the optional serial control bus. The Des features enhance signal quality on the link by
supporting: an equalizer input and also the FPD-Link II data coding that provides randomization, scrambling, and
DC balancing of the data. The Des includes multiple features to reduce EMI associated with display data
transmission. This includes the randomization and scrambling of the data and also the output spread spectrum
clock generation (SSCG) support. The Des features power saving features with a power down mode, and
optional LVCMOS (1.8 V) interface compatibility.
Image Enhancement Features
White Balance
The White Balance feature enables similar display appearance when using LCD’s from different vendors. It
compensates for native color temperature of the display, and adjusts relative intensities of R, G, B to maintain
specified color temperature. Programmable control registers are used to define the contents of three LUTs (8-bit
color value for Red, Green and Blue) for the White Balance Feature. The LUTs map input RGB values to new
output RGB values. There are three LUTs, one LUT for each color. Each LUT contains 256 entries, 8-bits per
entry with a total size of 6144 bits (3 x 256 x 8). All entries are readable and writable. Calibrated values are
loaded into registers through the I2C interface (deserializer is a slave device). This feature may also be applied
to lower color depth applications such as 18–bit (666) and 16–bit (565). White balance is enabled and configured
via serial bus register control.
16
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
LUT contents. The user must define and load the contents of the LUT for each color (R,G,B). Regardless of the
color depth being driven (888, 666, 656), the user must always provide contents for 3 complete LUTs - 256
colors x 8 bits x 3 tables. Unused bits - LSBs -shall be set to “0” by the user.
When 24-bit (888) input data is being driven to a 24-bit display, each LUT (R, G and B) must contain 256 unique
8-bit entries. The 8-bit white balanced data is then available at the output of the DS90UR916 deserailizer, and
driven to the display.
When 18-bit (666) input data is being driven to an 18-bit display, the white balance feature may be used in one of
two ways. First, simply load each LUT with 256, 8-bit entries. Each 8-bit entry is a 6-bit value (6 MSBs) with the 2
LSBs set to “00”. Thus as total of 64 unique 6-bit white balance output values are available for each color (R, G
and B). The 6-bit white balanced data is available at the output of the DS90UR916 deserializer, and driven
directly to the display.
Alternatively, with 6-bit input data the user may choose to load complete 8-bit values into each LUT. This mode
of operation provides the user with finer resolution at the LUT output to more closely achieve the desired white
point of the calibrated display. Although 8-bit data is loaded, only 64 unique 8-bit white balance output values are
available for each color (R, G and B). The result is 8-bit white balanced data. Before driving to the output of the
deserializer, the 8-bit data must be reduced to 6-bit with an FRC dithering function. To operate in this mode, the
user must configure the DS90UR916 to enable the FRC2 function.
Examples of the three types of LUT configurations described are shown in Figure 16.
Enabling white balance.The user must load all 3 LUTs prior to enabling the white balance feature. The following
sequence must be followed by the user.
To initialize white balance after power-on:
1. Load contents of all 3 LUTs . This requires a sequential loading of LUTs - first RED, second GREEN, third
BLUE. 256, 8-bit entries must be loaded to each LUT. Page registers must be set to select each LUT.
2. Enable white balance
By default, the LUT data may not be reloaded after initialization at power-on.
An option does exist to allow LUT reloading after power-on and initial LUT loading (as described above). This
option may only be used after enabling the white balance reload feature via the associated serial bus control
register. In this mode the LUTs may be reloaded by the master controller via I2C. This provides the user with the
flexibility to refresh LUTs periodically , or upon system requirements to change to a new set of LUT values. The
host controller loads the updated LUT values via the serial bus interface. There is no need to disable the white
balance feature while reloading the LUT data. Refreshing the white balance to the new set of LUT data will be
seamless - no interruption of displayed data.
It is important to note that initial loading of LUT values requires that all 3 LUTs be loaded sequentially. When
reloading, partial LUT updates may be made. Refer to USING IMAGE ENHANCEMENT FEATURES for a
detailed description of the LUT loading and reloading procedures.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
8-bit in / 8 bit out
6-bit in / 6 bit out
6-bit in / 8 bit out
Gray level Data Out
Gray level Data Out
Gray level Data Out
Entry
(8-bits)
Entry
(8-bits)
Entry
(8-bits)
0
1
2
3
4
5
6
7
8
9
00000000b
00000001b
00000011b
00000011b
00000110b
00000110b
00000111b
00000111b
00001000b
00001010b
0 00000000b
1 N/A
0
00000001b
1 N/A
2 N/A
3 N/A
2 N/A
3 N/A
4 00000100b
5 N/A
4
00000110b
5 N/A
6 N/A
7 N/A
6 N/A
7 N/A
8 00001000b
9 N/A
8
00001011b
9 N/A
10 N/A
11 N/A
10 00001001b
11 00001011b
10 N/A
11 N/A
.
.
.
.
.
.
248 11111010b
249 11111010b
250 11111011b
251 11111011b
252 11111110b
253 11111101b
254 11111101b
255 11111111b
248 11111000b
249 N/A
248 11111010b
249 N/A
250 N/A
250 N/A
251 N/A
252 11111100b
253 N/A
251 N/A
252 11111111b
253 N/A
254 N/A
255 N/A
254 N/A
255 N/A
Figure 16. White Balance LUT Configurations
Adaptive Hi-FRC Dithering
The Adaptive FRC Dithering Feature delivers product-differentiating image quality. It reduces 24-bit RGB (8 bits
per sub-pixel) to 18-bit RGB (6 bits per sub-pixel), smoothing color gradients, and allowing the flexibility to use
lower cost 18-bit displays. FRC (Frame Rate Control) dithering is a method to emulate “missing” colors on a
lower color depth LCD display by changing the pixel color slightly with every frame. FRC is achieved by
controlling on and off pixels over multiple frames (Temporal). Static dithering regulates the number of on and off
pixels in a small defined pixel group (Spatial). The FRC module includes both Temporal and Spatial methods and
also Hi-FRC. Conventional FRC can display only 16,194,277 colors with 6-bit RGB source. “Hi-FRC” enables full
(16,777,216) color on an 18-bit LCD panel. The “adaptive” FRC module also includes input pixel detection to
apply specific Spatial dithering methods for smoother gray level transitions. When enabled, the lower LSBs of
each RGB output are not active; only 18 bit data (6 bits per R,G and B) are driven to the display. This feature is
enabled via serial bus register control.
Two FRC functional blocks are available, and may be independently enabled. FRC1 precedes the white balance
LUT, and is intended to be used when 24-bit data is being driven to an 18-bit display with a white balance LUT
that is calibrated for an 18-bit data source. The second FRC block, FRC2, follows the white balance block and is
intended to be used when fine adjustment of color temperature is required on an 18-bit color display, or when a
24-bit source drives an 18-bit display with a white balance LUT calibrated for 24-bit source data.
For proper operation of the FRC dithering feature, the user must provide a description of the display timing
control signals. The timing mode, “sync mode” (HS, VS) or “DE only” must be specified, along with the active
polarity of the timing control signals. All this information is entered to DS90UR916 control registers via the serial
bus interface.
Adaptive Hi-FRC dithering consists of several components. Initially, the incoming 8-bit data is expanded to 9-bit
data. This allows the effective dithered result to support a total of 16.7 million colors. The incoming 9-bit data is
evaluated, and one of four possible algorithms is selected. The majority of incoming data sequences are
supported by the default dithering algorithm. Certain incoming data patterns (black/white pixel, full on/off sub-
pixel) require special algorithms designed to eliminate visual artifacts associated with these specific gray level
transitions. Three algorithms are defined to support these critical transitions.
An example of the default dithering algorithm is illustrated in Figure 17. The “1” or “0” value shown in the table
describes whether the 6-bit value is increased by 1 (“1”) or left unchanged (“0”). In this case, the 3 truncated
LSBs are “001”.
18
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
F0L0
PD1
Frame = 0, Line = 0
Pixel Data one
Cell Value 010
R[7:2]+0, G[7:2]+1, B[7:2]+0
LSB=001
three lsb of 9 bit data (8 to 9 for Hi-Frc)
Pixel Index
PD1
PD2
PD3
PD4
PD5
PD6
PD7
PD8
LSB = 001
F0L0
F0L1
F0L2
F0L3
010
101
000
000
000
000
000
000
000
000
010
101
000
000
000
000
000
101
010
000
000
000
000
000
010
000
000
101
000
000
000
000
R = 4/32
G = 4/32
B = 4/32
F1L0
F1L1
F1L2
F1L3
000
000
000
000
000
111
000
000
000
000
000
000
000
000
000
111
000
000
000
000
000
111
000
000
000
000
000
000
000
000
000
111
R = 4/32
G = 4/32
B = 4/32
F2L0
F2L1
F2L2
F2L3
000
000
010
101
000
000
000
000
010
101
000
000
000
000
000
000
010
000
000
101
000
000
000
000
000
101
010
000
000
000
000
000
R = 4/32
G = 4/32
B = 4/32
F3L0
F3L1
F3L2
F3L3
000
000
000
000
000
000
000
111
000
000
000
000
000
111
000
000
000
000
000
000
000
000
000
111
000
000
000
000
000
111
000
000
R = 4/32
G = 4/32
B = 4/32
Figure 17. Default FRC Algorithm
Signal Quality Enhancers
Des — Input Equalizer Gain (EQ)
The Des can enable receiver input equalization of the serial stream to increase the eye opening to the Des input.
Note this function cannot be seen at the RxIN+/- input but can be observed at the serial test port (CMLOUTP/N)
enabled via the Serial Bus control registers. The equalization feature may be controlled by the external pin or by
register.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
Table 2. Receiver Equalization Configuration Table
INPUTS
Effect
EQ3
L
EQ2
L
EQ1
L
EQ0
H
~1.5 dB
~3 dB
L
L
H
L
H
L
H
H
L
H
~4.5 dB
~6 dB
L
H
L
H
H
H
H
H
X
H
~7.5 dB
~9 dB
L
H
L
H
H
H
X
H
~10.5 dB
~12 dB
OFF*
H
X
H
L
* Default Setting is EQ = Off
The quality of the equalized signal may be assessed by monitoring the differential eye opening at the
CMLOUTP/N. The Receiver Differential Input Threshold and Input Jitter Tolerance define the acceptable data
eye opening. A differential probe should be used to measure across a 100Ohm termination resistor between the
CMLOUTP/N pins. Figure 18 illustrates the eye opening.
Ideal Data Bit
End
Ideal Data Bit
Beginning
Minimum Eye
Width
≥ VTH - VTL
RxIN_TOL -L
RxIN_TOL -R
t
BIT
(1UI)
Figure 18. CMLOUT Eye Opening
EMI Reduction Features
Output Slew (OS_PCLK/DATA)
The parallel bus outputs (RGB[7:0], VS, HS, DE and PCLK) of the Des feature a selectable output slew. The
DATA ((RGB[7:0], VS, HS, DE) are controlled by strap pin or register bit OS_DATA. The PCLK is controlled by
strap pin or register bit OS_PCLK. When the OS_PCLK/DATA = HIGH, the maximum slew rate is selected.
When the OS_PCLK/DATA = LOW, the minimum slew rate is selected. Use the higher slew rate setting when
driving longer traces or a heavier capacitive load.
Common Mode Filter Pin (CMF) — Optional
The Des provides access to the center tap of the internal termination. A capacitor may be placed on this pin for
additional common-mode filtering of the differential pair. This can be useful in high noise environments for
additional noise rejection capability. A 0.1µF capacitor may be connected to this pin to Ground.
SSCG Generation — Optional
The Des provides an internally generated spread spectrum clock (SSCG) to modulate its outputs. Both clock and
data outputs are modulated. This will aid to lower system EMI. Output SSCG deviations to ±2.0% (4% total) at up
to 35kHz modulations nominally are available. See Table 3. This feature may be controlled by external STRAP
pins or by register.
20
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
Table 3. SSCG Configuration (LF_MODE = L) — Des Output
SSC[3:0] Inputs
Result
LF_MODE = L (20 - 65 MHz)
SSC3
SSC2
L
SSC1
L
SSC0
L
fdev (%)
Off
fmod (kHz)
L
L
Off
L
L
H
L
±0.5
±1.0
±1.5
±2.0
±0.5
±1.0
±1.5
±2.0
±0.5
±1.0
±1.5
±2.0
±0.5
±1.0
±1.5
L
L
H
H
L
PCLK/2168
PCLK/1300
L
L
H
L
L
H
H
H
H
L
L
L
H
L
L
H
H
L
L
H
L
H
H
H
H
H
H
H
H
L
L
H
L
L
H
H
L
PCLK/868
PCLK/650
L
H
L
H
H
H
H
L
H
L
H
H
H
Table 4. SSCG Configuration (LF_MODE = H) — Des Output
SSC[3:0] Inputs
Result
LH_MODE = H (5 - 20 MHz)
SSC3
L
SSC2
L
SSC1
L
SSC0
L
fdev (%)
Off
fmod (kHz)
Off
L
L
L
H
L
±0.5
±1.0
±1.5
±2.0
±0.5
±1.0
±1.5
±2.0
±0.5
±1.0
±1.5
±2.0
±0.5
±1.0
±1.5
L
L
H
H
L
PCLK/620
PCLK/370
L
L
H
L
L
H
H
H
H
L
L
L
H
L
L
H
H
L
L
H
L
H
H
H
H
H
H
H
H
L
L
H
L
L
H
H
L
PCLK/258
PCLK/192
L
H
L
H
H
H
H
L
H
L
H
H
H
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
Frequency
fdev(max)
F
F
PCLK+
F
PCLK
fdev(min)
Time
PCLK-
1/fmod
Figure 19. SSCG Waveform
1.8V or 3.3V VDDIO Operation
The Des parallel bus and Serial Bus Interface can operate with 1.8 V or 3.3 V levels (VDDIO) for target (Display)
compatibility. The 1.8 V levels will offer a lower noise (EMI) and also a system power savings.
Power Saving Features
PowerDown Feature (PDB)
The Des has a PDB input pin to ENABLE or POWER DOWN the device. This pin can be controlled by the
system to save power, disabling the Des when the display is not needed. An auto detect mode is also available.
In this mode, the PDB pin is tied High and the Des will enter POWER DOWN when the serial stream stops.
When the serial stream starts up again, the Des will lock to the input stream and assert the LOCK pin and output
valid data. In POWER DOWN mode, the Data and PCLK output states are determined by the OSS_SEL status.
Note – in POWER DOWN, the optional Serial Bus Control Registers are RESET.
Stop Stream SLEEP Feature
The Des will enter a low power SLEEP state when the input serial stream is stopped. A STOP condition is
detected when the embedded clock bits are not present. When the serial stream starts again, the Des will then
lock to the incoming signal and recover the data. Note – in STOP STREAM SLEEP, the optional Serial Bus
Control Registers values are RETAINED.
CLOCK-DATA RECOVERY STATUS FLAG (LOCK) and OUTPUT STATE SELECT (OSS_SEL)
When PDB is driven HIGH, the CDR PLL begins locking to the serial input and LOCK goes from TRI-STATE to
LOW (depending on the value of the OSS_SEL setting). After the DS90UR916Q completes its lock sequence to
the input serial data, the LOCK output is driven HIGH, indicating valid data and clock recovered from the serial
input is available on the parallel bus and PCLK outputs. The PCLK output is held at its current state at the
change from OSC_CLK (if this is enabled via OSC_SEL) to the recovered clock (or vice versa).
If there is a loss of clock from the input serial stream, LOCK is driven Low and the state of the RGB/VS/HS/DE
outputs are based on the OSS_SEL setting (STRAP PIN configuration or register).
Oscillator Output — Optional
The Des provides an optional PCLK output when the input clock (serial stream) has been lost. This is based on
an internal oscillator. The frequency of the oscillator may be selected. This feature may be controlled by the
external pin or by register. See Table 6 and Table 7.
22
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
Table 5. OSS_SEL and PDB Configuration — Des Outputs(1)
INPUTS
OUTPUTS
RGB/HS/VS/DE
Serial Input
PDB
L
OSS_SEL
PCLK
LOCK
PASS
X
X
L
Z
L
Z
L
Z
L
Z
L
Static
Static
Active
H
H
H
X
Z
Z*
L
L
H
Active
Active
H
H
(1) If pin is strapped HIGH, output will be pulled up
Table 6. OSC (Oscillator) Mode — Des Output
INPUTS
Embedded PCLK
See(1)
OUTPUTS
PCLK
OSC Output
Toggling
RGB/HS/VS/DE
LOCK
PASS
L
L
L
Present
Active
H
H
(1) Absent and OSC_SEL ≠ 000
PDB
(DES)
RIN
(Diff.)
active serial stream
X
H
H
LOCK
L
Z
Z
Z
L
Z
Z
Z
RGB[7:0],
HS, VS, DE
Z
Z
PCLK*
(DES)
H
H
PASS
L
L
Z
Z
Locking
Active
C0 or C1 Error
In Bit Stream
Active
OFF
OFF
(Loss of LOCK)
CONDITIONS: * RFB = L, and OSS_SEL = H
Figure 20. Des Outputs with Output State Select Low (OSS_SEL = H)
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
PDB
(DES)
RIN
(Diff.)
active serial stream
X
H
H
LOCK
Z
L
L
L
L
L
Z
L
L
L
RGB[7:0],
HS, VS, DE
PCLK*
(DES)
H
H
PASS
L
L
Z
Z
C0 or C1 Error
In Bit Stream
Locking
Active
Active
OFF
OFF
(Loss of LOCK)
CONDITIONS: * RFB = L, and OSS_SEL = L
Figure 21. Des Outputs with Output State Select High (OSS_SEL = L)
Table 7. OSC_SEL (Oscillator) Configuration
OSC_SEL[2:0] INPUTS
PCLK Oscillator Output
OSC_SEL2
OSC_SEL1
OSC_SEL0
L
L
L
L
L
H
L
Off – Feature Disabled – Default
50 MHz ±40%
L
H
H
L
25 MHz ±40%
L
H
L
16.7 MHz ±40%
12.5 MHz ±40%
10 MHz ±40%
H
H
H
H
L
H
L
H
H
8.3 MHz ±40%
H
6.3 MHz ±40%
24
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
PDB
(DES)
RIN
(Diff.)
active serial stream
X
H
H
LOCK
Z
L
L
L
L
L
Z
RGB[7:0],
HS, VS, DE
L
L
PCLK*
(DES)
f
f
H
H
PASS
L
Z
L
Z
Locking
Active
C0 or C1 Error
In Bit Stream
Active
OFF
OFF
(Loss of LOCK)
CONDITIONS: * RFB = L, OSS_SEL = L , and OSC_SEL not equal to 000.
Figure 22. Des Outputs with Output State High and PCLK Output Oscillator Option Enabled
OP_LOW — Optional
The OP_ LOW feature is used to hold the LVCMOS outputs (except the LOCK output) at a LOW state. This
feature is enabled by setting the OP_LOW strap pin = HIGH, followed by the rising edge of PDB. The user must
toggle the OP_LOW Set/Reset register bit to release the outputs to the normal toggling state. Note that the
release of the outputs can only occur when LOCK is HIGH. When the OP_LOW feature is enabled, anytime
LOCK = LOW, the LVCMOS outputs will toggle to a LOW state again. The OP_ LOW strap pin feature is
assigned to output PASS pin 42.
Restrictions on other straps:
1) Other straps should not be used in order to keep RGB[7:0], HS, VS, DE, and PCLK at a true LOW state. Other
features should be selected thru I2C.
2) OSS_SEL function is not available when O/P_LOW is tied H.
Outputs RGB[7:0], HSYNC, VSYNC, DE, and PCLK are in TRI-STATE before PDB toggles HIGH because the
OP_LOW strap value has not been recognized until the DS90UR916 powers up. Figure 23 shows the user
controlled release of OP_LOW and automatic reset of OP_LOW set on the falling edge of LOCK. Figure 24
shows the user controlled release of OP_LOW and manual reset of OP_LOW set. Note manual reset of
OP_LOW can only occur when LOCK is H.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
2.0V
PDB
LOCK
OP_ LOW
SET
(Strap pin)
User
User
controlled
controlled
OP_ LOW
RELEASE/SET
(Register)
RGB[7:0],
HS, VS, DE
TRI-
STATE
ACTIVE
ACTIVE
ACTIVE
TRI-
STATE
ACTIVE
PCLK
Figure 23. OP_LOW Auto Set
2.0V
PDB
LOCK
OP_LOW
SET
(Strap pin)
User
User
controlled
controlled
OP_ LOW
RELEASE/SET
(Register)
RGB[7:0],
HS, VS, DE
TRI-
STATE
ACTIVE
ACTIVE
TRI-
STATE
PCLK
Figure 24. OP_LOW Manual Set/Reset
Pixel Clock Edge Select (RFB)
The RFB pin determines the edge that the data is strobed on. If RFB is High, output data is strobed on the Rising
edge of the PCLK. If RFB is Low, data is strobed on the Falling edge of the PCLK. This allows for inter-
operability with downstream devices. The Des output does not need to use the same edge as the Ser input. This
feature may be controlled by the external pin or by register.
26
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
Control Signal Filter — Optional
The Des provides an optional Control Signal (VS, HS, DE) filter that monitors the three video control signals and
eliminates any pulses that are 1 or 2 PCLKs wide. Control signals must be 3 pixel clocks wide (in its HIGH or
LOW state, regardless of which state is active). This is set by the CONFIG[1:0] or by the Control Register. This
feature may be controlled by the external pin or by Register.
Low Frequency Optimization (LF_Mode)
This feature may be controlled by the external pin or by Register.
Des — Map Select
This feature may be controlled by the external pin or by Register.
Table 8. Map Select Configuration
INPUTS
Effect
MAPSEL1
MAPSEL0
L
L
Bit 4, Bit 5 on LSB
DEFAULT
L
H
LSB 0 or 1
LSB 0
H
H or L
Strap Input Pins
Configuration of the device maybe done via configuration input pins and the STRAP input pins, or via the Serial
Control Bus. The STRAP input pins share select parallel bus output pins. They are used to load in configuration
values during the initial power up sequence of the device. Only a pull-up on the pin is required when a HIGH is
desired. By default the pad has an internal pull down, and will bias Low by itself. The recommended value of the
pull up is 10 kΩ to VDDIO; open (NC) for Low, no pull-down is required (internal pull-down). If using the Serial
Control Bus, no pull ups are required.
Optional Serial Bus Control
Please see the following section on the optional Serial Bus Control Interface.
Optional BIST Mode
Please see the following section on the chipset BIST mode for details.
Built In Self Test (BIST)
An optional At-Speed Built In Self Test (BIST) feature supports the testing of the high-speed serial link. This is
useful in the prototype stage, equipment production, in-system test and also for system diagnostics. In the BIST
mode only a input clock is required along with control to the Ser and Des BISTEN input pins. The Ser outputs a
test pattern (PRBS7) and drives the link at speed. The Des detects the PRBS7 pattern and monitors it for errors.
A PASS output pin toggles to flag any payloads that are received with 1 to 24 errors. Upon completion of the
test, the result of the test is held on the PASS output until reset (new BIST test or Power Down). A high on PASS
indicates NO ERRORS were detected. A Low on PASS indicates one or more errors were detected. The duration
of the test is controlled by the pulse width applied to the Des BISTEN pin. During the BIST duration the
deserializer data outputs toggle with a checkerboard pattern.
Inter-operability is supported between this FPD-Link II device and all FPD-Link II generations (Gen 1/2/3) — see
respective datasheets for details on entering BIST mode and control.
Sample BIST Sequence
See Figure 25 for the BIST mode flow diagram.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
27
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
Step 1: Place the DS90UR905 Ser in BIST Mode by setting Ser BISTEN = H. For the DS90UR905 Ser or
DS99R421 FPD-Link II Ser BIST Mode is enabled via the BISTEN pin. For the DS90C241 Ser or DS90UR241
Ser, BIST mode is enetered by setting all the input data of the device to Low state. A PCLK is required for all the
Ser options. When the Des detects the BIST mode pattern and command (DCA and DCB code) the RGB and
control signal outputs are shut off.
Step 2: Place the DS90UR916Q Des in BIST mode by setting the BISTEN = H. The Des is now in the BIST
mode and checks the incoming serial payloads for errors. If an error in the payload (1 to 24) is detected, the
PASS pin will switch low for one half of the clock period. During the BIST test, the PASS output can be
monitored and counted to determine the payload error rate.
Step 3: To Stop the BIST mode, the Des BISTEN pin is set Low. The Des stops checking the data and the final
test result is held on the PASS pin. If the test ran error free, the PASS output will be High. If there was one or
more errors detected, the PASS output will be Low. The PASS output state is held until a new BIST is run, the
device is RESET, or Powered Down. The BIST duration is user controlled by the duration of the BISTEN signal.
Step 4: To return the link to normal operation, the Ser BISTEN input is set Low. The Link returns to normal
operation.
Figure 26 shows the waveform diagram of a typical BIST test for two cases. Case 1 is error free, and Case 2
shows one with multiple errors. In most cases it is difficult to generate errors due to the robustness of the link
(differential data transmission etc.), thus they may be introduced by greatly extending the cable length, faulting
the interconnect, reducing signal condition enhancements (De-Emphasis, VODSEL, or Rx Equalization).
Normal
Step 1: SER in BIST
BIST
Wait
Step 2: Wait, DES in BIST
BIST
start
Step 3: DES in Normal
Mode - check PASS
BIST
stop
Step 4: SER in Normal
Figure 25. BIST Mode Flow Diagram
BER Calculations
It is possible to calculate the approximate Bit Error Rate (BER). The following is required:
•
•
•
Pixel Clock Frequency (MHz)
BIST Duration (seconds)
BIST test Result (PASS)
The BER is less than or equal to one over the product of 24 times the PCLK rate times the test duration. If we
assume a 65MHz PCLK, a 10 minute (600 second) test, and a PASS, the BERT is ≤ 1.07 X 10E-12
The BIST mode runs a check on the data payload bits. The LOCK pin also provides a link status. It the recovery
of the C0 and C1 bits does not reconstruct the expected clock signal, the LOCK pin will switch Low. The
combination of the LOCK and At-Speed BIST PASS pin provides a powerful tool for system evaluation and
performance monitoring.
28
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
BISTEN
(SER)
BISTEN
(DES)
PCLK
(RFB = L)
RGB[7:0]
HS, VS, DE
DATA
(internal)
PASS
Prior Result
Prior Result
PASS
FAIL
X = bit error(s)
DATA
(internal)
X
X
X
PASS
BIST
Result
Normal
PRBS
Normal
BIST Test
BIST Duration
Held
Figure 26. BIST Waveforms
Optional Serial Bus Control
The DS90UR916 may also be configured by the use of a serial control bus that is I2C protocol compatible. By
default, the I2C reg_0x00'h is set to 00'h and all configuration is set by control/strap pins. A write of 01'h to
reg_0x00'h will enable/allow configuration by registers; this will override the control/strap pins. Multiple devices
may share the serial control bus since multiple addresses are supported. See Figure 27.
1.8V
10 k
V
DDIO
ID[X]
4.7k
4.7k
SER
or
R
ID
HOST
SCL
SDA
SCL
SDA
DES
To other
Devices
Figure 27. Serial Control Bus Connection
The serial bus is comprised of three pins. The SCL is a Serial Bus Clock Input. The SDA is the Serial Bus Data
Input / Output signal. Both SCL and SDA signals require an external pull up resistor to VDDIO. For most
applications a 4.7 k pull up resistor to VDDIO may be used. The resistor value may be adjusted for capacitive
loading and data rate requirements. The signals are either pulled High, or driven Low.
The third pin is the ID[X] pin. This pin sets one of four possible device addresses. Two different connections are
possible. The pin may be pulled to VDD (1.8V, NOT VDDIO)) with a 10 kΩ resistor; or a 10 kΩ pull up resistor (to
VDD1.8V, NOT VDDIO)) and a pull down resistor of the recommended value to set other three possible addresses
may be used. See Table 9. Do not tie ID[x] directly to VSS.
The Serial Bus protocol is controlled by START, START-Repeated, and STOP phases. A START occurs when
SCL transitions Low while SDA is High. A STOP occurs when SDA transition High while SCL is also HIGH. See
Figure 28.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
29
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
SDA
SCL
S
P
START condition, or
STOP condition
START repeat condition
Figure 28. START and STOP Conditions
To communicate with a remote device, the host controller (master) sends the slave address and listens for a
response from the slave. This response is referred to as an acknowledge bit (ACK). If a slave on the bus is
addressed correctly, it Acknowledges (ACKs) the master by driving the SDA bus low. If the address doesn't
match a device's slave address, it Not-acknowledges (NACKs) the master by letting SDA be pulled High. ACKs
also occur on the bus when data is being transmitted. When the master is writing data, the slave ACKs after
every data byte is successfully received. When the master is reading data, the master ACKs after every data
byte is received to let the slave know it wants to receive another data byte. When the master wants to stop
reading, it NACKs after the last data byte and creates a stop condition on the bus. All communication on the bus
begins with either a Start condition or a Repeated Start condition. All communication on the bus ends with a Stop
condition. A READ is shown in Figure 29 and a WRITE is shown in Figure 30.
If the Serial Bus is not required, the three pins may be left open (NC).
Table 9. ID[x] Resistor Value – DS90UR916Q Des
Resistor
RID* kΩ (5% tol)
Address
7'b
Address
8'b
0 appended
(WRITE)
0.47
2.7
7b' 111 0001 (h'71)
7b' 111 0010 (h'72)
7b' 111 0011 (h'73)
7b' 111 0110 (h'76)
8b' 1110 0010 (h'E2)
8b' 1110 0100 (h'E4)
8b' 1110 0110 (h'E6)
8b' 1110 1100 (h'EC)
8.2
Open
*Note: RID ≠ 0 ohm, do not connect directly to VSS (GND), this is not a valid address.
Register Address
Slave Address
Slave Address
Data
a
c
k
a
c
k
a
c
k
a
c
k
A
2
A
1
A
0
A
2
A
1
A
0
0
S
S
1
P
Figure 29. Serial Control Bus — READ
Register Address
Slave Address
Data
a
c
a
c
k
a
c
k
A
2
A
1
A
0
0
S
P
k
Figure 30. Serial Control Bus — WRITE
30
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
Table 10. DESERIALIZER — Serial Bus Control Registers
ADD
(dec) (hex)
ADD
Default
(bin)
PAGE
Register Name
Bit(s)
R/W
Function
Description
0
0
0
Des Config 1
7
R/W
0
LFMODE
0: 20 to 65 MHz Operation
1: 5 to 20 MHz Operation
6
5
R/W
R/W
R/W
R/W
0
OS_PCLK
OS_DATA
RFB
0: Normal PCLK Output Slew
1: Increased PCLK Slew
0
0: Normal DATA OUTPUT Slew
1: Increased Data Slew
4
0
0: Data strobed on Falling edge of PCLK
1: Data strobed on Rising edge of PCLK
3:2
00
CONFIG
00: Normal Mode, Control Signal Filter
Disabled
01: Normal Mode, Control Signal Filter
Enabled
10: Backwards Compatible (DS90UR241)
11: Backwards Compatible (DS90C241)
1
0
R/W
0
SLEEP
Note – not the same function as
PowerDown (PDB)
0: normal mode
1: Sleep Mode – Register settings
retained.
R/W
R/W
0
0
REG Control
0: Configurations set from control pins /
STRAP pins
1: Configurations set from registers (except
I2C_ID)
0
0
1
2
1
2
Slave ID
7
0: Address from ID[X] Pin
1: Address from Register
6:0
R/W 1110000 ID[X]
Serial Bus Device ID, Four IDs are:
7b '1110 001 (h'71)
7b '1110 010 (h'72)
7b '1110 011 (h'73)
7b '1110 110 (h'76)
All other addresses are Reserved.
Des Features 1
7
6
R/W
R/W
R/W
0
0
OP_LOW
Release/Set
0: set outputs state LOW (except LOCK)
1: release output LOW state, outputs
toggling normally
Note: This register only works during LOCK
= 1.
OSS_SEL
MAP_SEL
Output Sleep State Select
0:PCLK/RGB[7:0]/HS/VS/DE = L, LOCK =
Normal, PASS = H
1:PCLK/RGB[7:0]/HS/VS/DE = Tri-State,
LOCK = Normal, PASS = H
5:4
00
Special for Backwards Compatible Mode
with DS90UR241)
00: bit 4, 5 on LSB
01: LSB zero or one
10: LSB zero
11: LSB zero
3
R/W
R/W
0
OP_LOW strap
bypass
0: strap will determine whether OP_LOW
feature is ON or OFF
1: Turns OFF OP_LOW feature
2:0
00
OSC_SEL
000: OFF
001: 50 MHz ±40%
010: 25 MHz ±40%
011: 16.7 MHz ±40%
100: 12.5 MHz ±40%
101: 10 MHz ±40%
110: 8.3 MHz ±40%
111: 6.3 MHz ±40%
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
31
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
Table 10. DESERIALIZER — Serial Bus Control Registers (continued)
ADD
(dec) (hex)
ADD
Default
(bin)
PAGE
Register Name
Bit(s)
R/W
Function
Description
0
3
3
Des Features 2
7:5
R/W
000
EQ Gain
000: ~1.625 dB
001: ~3.25 dB
010: ~4.87 dB
011: ~6.5 dB
100: ~8.125 dB
101: ~9.75 dB
110: ~11.375 dB
111: ~13 dB
4
R/W
R/W
0
EQ Enable
SSC
0: EQ = disabled
1: EQ = enabled
3:0
0000
IF LF_MODE = 0, then:
000: SSCG OFF
0001: fdev = ±0.5%, fmod = PCLK/2168
0010: fdev = ±1.0%, fmod = PCLK/2168
0011: fdev = ±1.5%, fmod = PCLK/2168
0100: fdev = ±2.0%, fmod = PCLK/2168
0101: fdev = ±0.5%, fmod = PCLK/1300
0110: fdev = ±1.0%, fmod = PCLK/1300
0111: fdev = ±1.5%, fmod = PCLK/1300
1000: fdev = ±2.0%, fmod = PCLK/1300
1001: fdev = ±0.5%, fmod = PCLK/868
1010: fdev = ±1.0%, fmod = PCLK/868
1011: fdev = ±1.5%, fmod = PCLK/868
1100: fdev = ±2.0%, fmod = PCLK/868
1101: fdev = ±0.5%, fmod = PCLK/650
1110: fdev = ±1.0%, fmod = PCLK/650
1111: fdev = ±1.5%, fmod = PCLK/650
IF LF_MODE = 1, then:
000: SSCG OFF
0001: fdev = ±0.5%, fmod = PCLK/620
0010: fdev = ±1.0%, fmod = PCLK/620
0011: fdev = ±1.5%, fmod = PCLK/620
0100: fdev = ±2.0%, fmod = PCLK/620
0101: fdev = ±0.5%, fmod = PCLK/370
0110: fdev = ±1.0%, fmod = PCLK/370
0111: fdev = ±1.5%, fmod = PCLK/370
1000: fdev = ±2.0%, fmod = PCLK/370
1001: fdev = ±0.5%, fmod = PCLK/258
1010: fdev = ±1.0%, fmod = PCLK/258
1011: fdev = ±1.5%, fmod = PCLK/258
1100: fdev = ±2.0%, fmod = PCLK/258
1101: fdev = ±0.5%, fmod = PCLK/192
1110: fdev = ±1.0%, fmod = PCLK/192
1111: fdev = ±1.5%, fmod = PCLK/192
0
0
4
4
CMLOUT Config
7
R/W
0
Repeater Enable
0: Output CMLOUTP/N = disabled
1: Output CMLOUTP/N = enabled
6:0
7
R/W 0000000 Reserved
Reserved
21
15
FRC
Configuration
R/W
0
Timing mode
select
Select display timing mode
0: DE only mode
1: Sync mode (VS, HS)
6
5
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
VS Polarity
HS Polarity
DE Polarity
FRC2 enable
FRC1 enable
Reserved
0: Active HIGH
1: Active LOW
0: Active HIGH
1: Active LOW
4
0: Active HIGH
1: Active LOW
3
0: FRC2 disabled
1: FRC2 enabled
2
0: FRC1 disabled
1: FRC1 enabled
[1:0]
Reserved
32
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
Table 10. DESERIALIZER — Serial Bus Control Registers (continued)
ADD
(dec) (hex)
ADD
Default
(bin)
PAGE
Register Name
Bit(s)
R/W
Function
Description
0
22
16
White Balance
Configuration
[7:6]
R/W
0
Page Setting
00: Configuration Registers
01: Red LUT
10: Green LUT
11: Blue LUT
5
4
R/W
R/W
0
0
White Balance
Enable
0: WB disabled
1: WB enabled
Reload Enable
0: Reload disabled
1: Reload enabled
[3:0]
0
Reserved
Reserved
1
2
3
0 -
255
00 - White Balance
FF Red LUT
[FF:0]
R/W
R/W
R/W
N/A
Red LUT
256 8–bit entries to be applied to the Red
subpixel data
0 -
255
00 - White Balance
FF Green LUT
[FF:0]
[FF:0]
N/A
N/A
Green LUT
Blue LUT
256 8–bit entries to be applied to the Green
subpixel data
0 -
255
00 - White Balance
FF Blue LUT
256 8–bit entries to be applied to the Blue
subpixel data
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
33
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
APPLICATIONS INFORMATION
DISPLAY APPLICATION
The DS90UR905/916Q chipset is intended for interface between a host (graphics processor) and a Display. It
supports an 24-bit color depth (RGB888) and up to 1024 X 768 display formats. In a RGB888 application, 24
color bits (R[7:0], G[7:0], B[7:0]), Pixel Clock (PCLK) and three control bits (VS, HS and DE) are supported
across the serial link with PCLK rates from 5 to 65 MHz. The chipset may also be used in 18-bit color
applications. In this application three to six general purpose signals may also be sent from host to display.
The Des is expected to be located close to its target device. The interconnect between the Des and the target
device is typically in the 1 to 3 inch separation range. The input capacitance of the target device is expected to
be in the 5 to 10 pF range. Care should be taken on the PCLK output trace as this signal is edge sensitive and
strobes the data. It is also assumed that the fanout of the Des is one. If additional loads need to be driven, a
logic buffer or mux device is recommended.
TYPICAL APPLICATION CONNECTION
Figure 31 shows a typical application of the DS90UR916Q Des using serial bus control mode for a 65 MHz 24-bit
Color Display Application. The LVDS inputs utilize 100 nF coupling capacitors to the line and the Receiver
provides internal termination. Bypass capacitors are placed near the power supply pins. At a minimum, seven 0.1
µF capacitors and two 4.7 µF capacitors should be used for local device bypassing. System GPO (General
Purpose Output) signals control the PDB and the BISTEN pins. In this application the RRFB pin is tied Low to
strobe the data on the falling edge of the PCLK.
The DS90UR916 will most often be used in serial bus control mode as this is required to enable the image
enhancement features of the device. The schematic illustrates the proper connection of SDA and SCL to the pull-
up resistors as well as the external resistor network to the ID[x] pin..
The interface to the target display is with 3.3V LVCMOS levels, thus the VDDIO pin is connected to the 3.3 V rail.
A delay cap is placed on the PDB signal to delay the enabling of the device until power is stable.
34
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
DS90UR916Q (DES)
VDDIO
1.8V
VDDL
VDDIO
VDDIO
VDDIO
C8
C3
C4
C5
C14
C11
C12 C15
FB2
FB1
FB3
FB4
FB5
VDDSC
VDDPR
VDDR
C9
C10
R7
R6
R5
R4
R3
R2
R1
R0
C16
C6
VDDIR
VDDCMLO
G7
G6
G5
G4
G3
G2
G1
G0
C17
C1
C7
FB6
LVCMOS
Parallel
Video
Interface
Serial
FPD-Link II
Interface
RIN+
RIN-
CMF
C2
B7
B6
B5
B4
B3
B2
B1
B0
C13
TP_A
TP_B
CMLOUTP
CMLOUTN
Host
Control
BISTEN
PDB
HS
VS
DE
C18
PCLK
LOCK
PASS
1.8V
10k
RID
8
NC
ID[X]
VDDIO
RES
DAP (GND)
4.7k
4.7k
SCL
SDA
C1 - C2 = 0.1 mF (50 WV)
C3 - C13 = 0.1 mF
C14 - C17 = 4.7 mF
C18 = >10 mF
RID (see ID[x] Resistor Value Table)
FB1-FB6: Impedance = 1 kW,
low DC resistance (<1W)
Figure 31. DS90UR916Q Typical Connection Diagram — Pin Control
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
35
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
POWER UP REQUIREMENTS AND PDB PIN
At power-on, the PDB pin must be LOW. The transition to the HIGH state (normal operating mode) may only
occur after all power supplies are stable and above the minimum recommended operating voltage. All other
LVCMOS inputs must also remain LOW prior to power supplies stabilized at the recommended operating
voltages. Active driving of inputs and the transition of PDB to the HIGH state should be delayed 1usec after
power supplies are stabilized.
TRANSMISSION MEDIA
The Ser/Des chipset is intended to be used in a point-to-point configuration, through a PCB trace, or through
twisted pair cable. The Ser and Des provide internal terminations providing a clean signaling environment. The
interconnect for LVDS should present a differential impedance of 100 Ohms. Use cables and connectors that
have matched differential impedance to minimize impedance discontinuities. Shielded or un-shielded cables may
be used depending upon the noise environment and application requirements.
LIVE LINK INSERTION
The Ser and Des devices support live pluggable applications. The automatic receiver lock to random data “plug &
go” hot insertion capability allows the DS90UR916Q to attain lock to the active data stream during a live insertion
event.
PCB LAYOUT AND POWER SYSTEM CONSIDERATIONS
Circuit board layout and stack-up for the LVDS Ser/Des devices should be designed to provide low-noise power
feed to the device. Good layout practice will also separate high frequency or high-level inputs and outputs to
minimize unwanted stray noise pickup, feedback and interference. Power system performance may be greatly
improved by using thin dielectrics (2 to 4 mils) for power / ground sandwiches. This arrangement provides plane
capacitance for the PCB power system with low-inductance parasitics, which has proven especially effective at
high frequencies, and makes the value and placement of external bypass capacitors less critical. External bypass
capacitors should include both RF ceramic and tantalum electrolytic types. RF capacitors may use values in the
range of 0.01 uF to 0.1 uF. Tantalum capacitors may be in the 2.2 uF to 10 uF range. Voltage rating of the
tantalum capacitors should be at least 5X the power supply voltage being used.
Surface mount capacitors are recommended due to their smaller parasitics. When using multiple capacitors per
supply pin, locate the smaller value closer to the pin. A large bulk capacitor is recommend at the point of power
entry. This is typically in the 50uF to 100uF range and will smooth low frequency switching noise. It is
recommended to connect power and ground pins directly to the power and ground planes with bypass capacitors
connected to the plane with via on both ends of the capacitor. Connecting power or ground pins to an external
bypass capacitor will increase the inductance of the path.
A small body size X7R chip capacitor, such as 0603, is recommended for external bypass. Its small body size
reduces the parasitic inductance of the capacitor. The user must pay attention to the resonance frequency of
these external bypass capacitors, usually in the range of 20-30 MHz. To provide effective bypassing, multiple
capacitors are often used to achieve low impedance between the supply rails over the frequency of interest. At
high frequency, it is also a common practice to use two vias from power and ground pins to the planes, reducing
the impedance at high frequency.
Some devices provide separate power and ground pins for different portions of the circuit. This is done to isolate
switching noise effects between different sections of the circuit. Separate planes on the PCB are typically not
required. Pin Description tables typically provide guidance on which circuit blocks are connected to which power
pin pairs. In some cases, an external filter many be used to provide clean power to sensitive circuits such as
PLLs.
Use at least a four layer board with a power and ground plane. Locate LVCMOS signals away from the LVDS
lines to prevent coupling from the LVCMOS lines to the LVDS lines. Closely-coupled differential lines of 100
Ohms are typically recommended for LVDS interconnect. The closely coupled lines help to ensure that coupled
noise will appear as common-mode and thus is rejected by the receivers. The tightly coupled lines will also
radiate less.
Information on the WQFN style package is provided in TI Application Note: AN-1187 (SNOA401).
36
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
LVDS INTERCONNECT GUIDELINES
See AN-1108 (SNLA008) and AN-905 (SNLA035) for full details.
•
•
Use 100Ω coupled differential pairs
Use the S/2S/3S rule in spacings
–
–
–
– S = space between the pair
– 2S = space between pairs
– 3S = space to LVCMOS signal
•
•
•
•
•
Minimize the number of Vias
Use differential connectors when operating above 500Mbps line speed
Maintain balance of the traces
Minimize skew within the pair
Terminate as close to the TX outputs and RX inputs as possible
Additional general guidance can be found in the LVDS Owner’s Manual - available in PDF format from the TI
web site at: www.ti.com/lvds
USING IMAGE ENHANCEMENT FEATURES
The DS90UR916Q offers two FRC dithering blocks and one White Balance lookup table. Depending upon the
color depth of the source data, display and LUT contents, these blocks may be independently enabled or
disabled in various combinations. Refer to Table 11 below for recommendations.
Table 11. Enabling Image Enhancement Features
Source
24-bit
24-bit
24-bit
18-bit
18-bit
18-bit
White Balance LUT
Display
24-bit
18-bit
18-bit
24-bit
18-bit
18-bit
FRC1
FRC2
24-bit
24-bit
18-bit
24-bit
24-bit
18-bit
Disabled
Disabled
Enabled
Disabled
Disabled
Disabled
Disabled
Enabled
Disabled
Disabled
Enabled
Disabled
If the white balance feature is to be used all 3 LUTs must be fully loaded after initial power-up. LUTs must be
loaded sequentially — first Red, second Green, third Blue — and all 256 values must be loaded into each LUT.
After power-up the following procedure must be followed.
1. Power-on (reload = disable by default)
2. Enable WB
3. Set page Register RED
4. Initial RED LUT load (all 256 bytes) '916 will self clear page register
5. Set page Register GREEN
6. Initial GREEN LUT load (all 256 bytes) '916 will self clear page register
7. Set page Register BLUE
8. Initial BLUE LUT load (all 256 bytes) '916 will self clear page register
Once all LUTs are loaded, ‘916 will enable the WB output
To reload LUT contents, after the initial load at power-up, the following procedure must be followed.
1. Enable RELOAD
2. Set appropriate page register (RED, GREEN or BLUE)
3. Load new LUT values (any sequence, any order, any number)
4. Load appropriate R, G or B 255 value to clear page register
5. Set appropriate page register (RED, GREEN or BLUE)
6. Load new LUT values (any sequence, any order, any number)
7. Load appropriate R, G or B 255 value to clear page register
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
37
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
8. Set appropriate page register (RED, GREEN or BLUE)
9. Load new LUT values (any sequence, any order, any number)
10. Load appropriate R, G or B 255 value to clear page register
11. Disable RELOAD
ALTERNATE COLOR / DATA MAPPING
Color Mapped data Pin names are provided to specify a recommended mapping for 24-bit Color Applications.
Seven [7] is assumed to be the MSB, and Zero [0] is assumed to be the LSB. While this is recommended it is not
required. When connecting to earlier generations of FPD-Link II Ser and Des devices, a color mapping review is
recommended to ensure the correct connectivity is obtained. Table 12 provides examples for interfacing to 18-bit
applications with or without the video control signals embedded. The DS90UR916Q Des also provides additional
flexibility with the MAP_SEL feature as well.
Table 12. Alternate Color / Data Mapping — See Text Below
18-bit
RGB
18-bit
RGB
18-bit
RGB
24-bit
RGB
905 Pin
Name
916 Pin
Name
24-bit
RGB
18-bit
RGB
18-bit
RGB
18-bit
RGB
0
LSB R0
R1
GP0
GP1
R0
RO
R1
R2
R3
R4
R5
R6
R7
G0
G1
G2
G3
G4
G5
G6
G7
B0
B1
B2
B3
B4
B5
B6
B7
HS
VS
DE
RO
R1
R2
R3
R4
R5
R6
R7
G0
G1
G2
G3
G4
G5
G6
G7
B0
B1
B2
B3
B4
B5
B6
B7
HS
VS
DE
R0
R1
R2
R3
R4
R5
R6
R7
G0
G1
G2
G3
G4
G5
G6
G7
B0
B1
B2
B3
B4
B5
B6
B7
HS
VS
DE
R0
R1
R2
R3
R4
R5
R6
R7
G0
G1
G2
G3
G4
G5
G6
G7
B0
B1
B2
B3
B4
B5
B6
B7
HS
VS
DE
GP0
GP1
R0
LSB R0
R1
0
0
0
R0
R1
R2
R3
R4
R5
0
R2
R2
R0
R1
R2
R3
R4
R5
0
R3
R1
R1
R3
R4
R2
R2
R4
MSB R5
LSB G0
G1
R3
R3
MSB R5
LSB G0
G1
R4
R4
R5
R5
G2
GP2
GP3
G0
G1
G2
G3
G4
G5
GP4
GP5
B0
GP2
GP3
G0
G1
G2
G3
G4
G5
GP4
GP5
B0
G2
0
G3
G3
0
G0
G1
G2
G3
G4
G5
0
G4
G4
G0
G1
G2
G3
G4
G5
0
MSB G5
LSB B0
B1
MSB G5
LSB0
B1
B2
B2
B3
B3
B4
B4
0
MSB B5
HS
MSB B5
HS
0
B0
B1
B2
B3
B4
B5
HS
VS
DE
B0
B1
B2
B3
B4
B5
HS
VS
VS
B1
B1
VS
DE
B2
B2
DE
GP0
GP1
GP2
GND
GND
GND
B3
B3
GP0
GP1
GP2
GND
GND
GND
B4
B4
B5
B5
HS
VS
DE
HS
VS
DE
Scenario
4
Scenario
3
Scenario
2
Scenario
1
905 Pin
Name
916 Pin
Name
Scenario
1
Scenario
2
Scenario
3
Scenario
4
38
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
DS90UR916Q
www.ti.com
SNOSB46E –MARCH 2011–REVISED APRIL 2013
Scenario 4
Scenario 4 supports an 18-bit RGB color mapping and 3 embedded video control signals. All LSBs are set to “0”.
FRC and white balance may be enabled with this scenario.
Scenario 3
Scenario 3 supports an 18-bit RGB color mapping, 3 un-embedded video control signals, and up to three general
purpose signals. This scenario is NOT supported when FRC or white balance are enabled on the DS90UR916.
Scenario 2
Scenario 2 supports an 18-bit RGB color mapping, 3 embedded video control signals, and up to six general
purpose signals. This scenario is NOT supported when FRC or white balance are enabled on the DS90UR916.
Scenario 1
Scenario 1 supports the 24-bit RGB color mapping, along with the 3 embedded video control signals. This is the
native mode for the chipset. FRC and white balance may be enabled with this scenario.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
39
Product Folder Links: DS90UR916Q
DS90UR916Q
SNOSB46E –MARCH 2011–REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Changes from Revision D (April 2013) to Revision E
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 39
40
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
DS90UR916QSQ/NOPB
DS90UR916QSQE/NOPB
DS90UR916QSQX/NOPB
ACTIVE
ACTIVE
ACTIVE
WQFN
WQFN
WQFN
NKB
NKB
NKB
60
60
60
1000 RoHS & Green
250 RoHS & Green
2000 RoHS & Green
SN
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
-40 to 105
-40 to 105
-40 to 105
UR916QSQ
SN
SN
UR916QSQ
UR916QSQ
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jun-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
DS90UR916QSQ/NOPB WQFN
DS90UR916QSQE/NOPB WQFN
DS90UR916QSQX/NOPB WQFN
NKB
NKB
NKB
60
60
60
1000
250
330.0
178.0
330.0
16.4
16.4
16.4
9.3
9.3
9.3
9.3
9.3
9.3
1.3
1.3
1.3
12.0
12.0
12.0
16.0
16.0
16.0
Q1
Q1
Q1
2000
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jun-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
DS90UR916QSQ/NOPB
DS90UR916QSQE/NOPB
DS90UR916QSQX/NOPB
WQFN
WQFN
WQFN
NKB
NKB
NKB
60
60
60
1000
250
356.0
208.0
356.0
356.0
191.0
356.0
35.0
35.0
35.0
2000
Pack Materials-Page 2
PACKAGE OUTLINE
NKB0060B
VQFN - 0.8 mm max height
S
C
A
L
E
1
.
5
0
0
PLASTIC QUAD FLATPACK - NO LEAD
9.1
8.9
A
B
PIN 1 INDEX AREA
9.1
8.9
0.8
0.7
C
SEATING PLANE
0.08 C
0.05
0.00
2X 7
6.3 0.1
SYMM
EXPOSED
THERMAL PAD
(0.1) TYP
16
30
15
31
SYMM
61
2X 7
1
0.3
60X
45
0.2
56X 0.5
60
46
0.1
C A B
0.7
0.5
PIN 1 ID
0.05
60X
4214995/A 03/2018
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
NKB0060B
VQFN - 0.8 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
(
6.3)
SYMM
SEE SOLDER MASK
DETAIL
60X (0.8)
60X (0.25)
46
60
1
45
56X (0.5)
(1.1) TYP
(1.2) TYP
SYMM
(R0.05) TYP
(
0.2) TYP
VIA
61
(0.6) TYP
(8.6)
15
31
30
16
(0.6) TYP
(1.2) TYP
(1.1) TYP
(8.6)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 8X
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
METAL UNDER
SOLDER MASK
METAL EDGE
EXPOSED METAL
SOLDER MASK
OPENING
EXPOSED
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
SOLDER MASK DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4214995/A 03/2018
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
NKB0060B
VQFN - 0.8 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
25X ( 1)
(1.2) TYP
46
60X (0.8)
60X (0.25)
60
1
45
56X (0.5)
(R0.05) TYP
(1.2) TYP
(8.6)
61
SYMM
15
31
16
30
SYMM
(8.6)
SOLDER PASTE EXAMPLE
BASED ON 0.125 MM THICK STENCIL
SCALE: 8X
EXPOSED PAD 61
63% PRINTED SOLDER COVERAGE BY AREA UNDER PACKAGE
4214995/A 03/2018
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明