DRV2604L [TI]
具有 2V 工作电压、波形存储器和自动谐振跟踪功能的 ERM/LRA 触觉驱动器;型号: | DRV2604L |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有 2V 工作电压、波形存储器和自动谐振跟踪功能的 ERM/LRA 触觉驱动器 驱动 存储 驱动器 |
文件: | 总73页 (文件大小:2899K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
DRV2604L 用于 LRA 和 ERM 的 2V 至 5.2V 触觉驱动器,
具有内部存储器和智能环路架构
1 特性
DRV2604L 器件集成有足够的 RAM,用户能够预装载
1
超过 100 个定制智能环路架构波形。这些波形可通过
I2C 即时回放,或者也可选择由硬件触发引脚来触发。
•
灵活的触觉和振动驱动器
–
–
LRA(线性谐振致动器)
ERM(偏轴转动惯量)
此外,主机处理器可利用实时回放模式绕过存储器回放
引擎并通过 I2C 从主机直接播放波形。
•
I2C 控制的数字回放引擎
–
–
–
–
波形序列器和触发器
DRV2604L 器件内部采用智能环路架构,可轻松实现
自动谐振 LRA 驱动,以及优化反馈的 ERM 驱动,从
而提供自动过驱动和制动。这种智能环路架构可构建简
化的输入波形接口,并且能够提供可靠的电机控制和稳
定的电机性能。此外,DRV2604L 器件还 能够 在
LRA 致动器不产生有效反电动势电压时自动切换至开
环系统。当 LRA 产生有效反电动势电压
通过 I2C 实现的实时回放模式
针对定制波形的内部 RAM
I2C 双模式驱动(开环和闭环)
•
智能环路架构(正在申请专利的控制算法)
–
–
–
–
–
自动过驱动和制动
自动谐振跟踪和报告(仅限 LRA)
自动致动器诊断
时,DRV2604L 器件会自动与 LRA 同步。 DRV2604L
还可以利用内部生成的 PWM 信号实现开环驱动。
自动级别校准
支持宽泛的致动器型号
•
•
•
•
•
Immersion TouchSense® 3000 兼容
可在电池放电过程进行驱动补偿
宽工作电压范围(2V 至 5.2V)
高效的差分开关输出驱动
器件信息(1)
器件型号
DRV2604L
DRV2604L
封装
DSBGA (9)
VSSOP (10)
封装尺寸(最大值)
1.50mm x 1.50mm
3.00mm × 3.00mm
(1) 如需了解所有可用封装,请参阅数据表末尾的可订购产品附
录。
脉宽调制 (PWM) 输入,占空比可控范围为 0% 至
100%
•
•
•
硬件触发输入
简化原理图
快速启动时间
V
DD
RAM
1.8V 兼容、VDD 耐压数字接口
OUT+
Supply
correction
Gate
drive
2 应用
2
SDA
SCL
I
C I/F
LRA
or
ERM
•
•
手机
Control and
playback engine
Back-EMF
detection
M
EN
平板电脑
IN/TRIG
REG
REG
OUTt
3 说明
Gate
drive
DRV2604L 器件是一款低压触觉驱动器,其闭环致动
器控制系统,可为 ERM 和 LRA 提供高质量的触觉反
馈。此方案有助于提升致动器在加速度稳定性、启动时
间和制动时间方面的性能,通过共用的 I2C 兼容总线或
PWM 输入信号即可触发该方案。
GND
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
English Data Sheet: SLOS866
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
目录
8.4 Device Functional Modes........................................ 19
8.5 Programming........................................................... 22
8.6 Register Map........................................................... 35
Application and Implementation ........................ 54
9.1 Application Information............................................ 54
9.2 Typical Application .................................................. 55
9.3 Initialization Setup................................................... 58
1
2
3
4
5
6
特性.......................................................................... 1
应用.......................................................................... 1
说明.......................................................................... 1
修订历史记录 ........................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 5
6.1 Absolute Maximum Ratings ...................................... 5
6.2 ESD Ratings.............................................................. 5
6.3 Recommended Operating Conditions....................... 5
6.4 Thermal Information.................................................. 5
6.5 Electrical Characteristics........................................... 6
6.6 Timing Requirements................................................ 6
6.7 Switching Characteristics.......................................... 6
6.8 Typical Characteristics.............................................. 8
Parameter Measurement Information .................. 9
7.1 Test Setup for Graphs............................................... 9
Detailed Description ............................................ 10
8.1 Overview ................................................................. 10
8.2 Functional Block Diagram ....................................... 10
8.3 Feature Description................................................. 11
9
10 Power Supply Recommendations ..................... 59
11 Layout................................................................... 60
11.1 Layout Guidelines ................................................. 60
11.2 Layout Example .................................................... 61
12 器件和文档支持 ..................................................... 62
12.1 文档支持................................................................ 62
12.2 接收文档更新通知 ................................................. 62
12.3 社区资源................................................................ 62
12.4 商标....................................................................... 62
12.5 静电放电警告......................................................... 62
12.6 Glossary................................................................ 62
13 机械、封装和可订购信息....................................... 62
7
8
4 修订历史记录
注:之前版本的页码可能与当前版本有所不同。
Changes from Revision E (August 2016) to Revision F
Page
•
•
•
•
Changed the DEFAULT value for bit 5-4 of Table 19 From: 1 To 3 ................................................................................... 46
Changed the DEFAULT value for bit 3-2 of Table 19 From: 2 To 1 ................................................................................... 47
Changed the DEFAULT value for bit 1-0 of Table 19 From: 2 To 1 ................................................................................... 48
Changed the typical value of C(VDD) in Table 29 From: 0.1 µF To: 1 µF .............................................................................. 54
Changes from Revision D (June 2015) to Revision E
Page
•
•
Table 2, changed 0x00 Bit 4 From: Reserved To: ILLEGAL_ADDR.................................................................................... 35
Status (Address: 0x00), changed 0x00 Bit 4 From: Reserved To: ILLEGAL_ADDR........................................................... 36
Changes from Revision C (September 2014) to Revision D
Page
•
已发布完整版数据表 ............................................................................................................................................................... 1
2
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
5 Pin Configuration and Functions
YZF Package
9-Pin DSBGA With 0.5-mm Pitch
(Top View)
1
2
3
EN
REG
OUT+
A
B
C
IN/TRIG
SCL
SDA
VDD
GND
OUTœ
Not to scale
Pin Functions
PIN
TYPE(1)
DESCRIPTION
NO.
A1
NAME
EN
I
Device enable
A2
REG
OUT+
O
O
The REG pin is the 1.8-V regulator output. A 1-µF capacitor is required.
A3
Positive haptic driver differential output
Multi-mode Input. I2C selectable as PWM, analog, or trigger. If not used, this pin should
be connected to GND
B1
IN/TRIG
I
B2
B3
C1
C3
C2
SDA
GND
SCL
I/O
P
I2C data
Supply ground
I2C clock
I
OUT–
VDD
O
P
Negative haptic-driver differential output
Supply input (2 to 5.2 V). A 1-µF capacitor is required.
(1) I = input, O = output, I/O = input and output, P = power
Copyright © 2014–2018, Texas Instruments Incorporated
3
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
DGS Package
10-Pin VSSOP
(Top View)
REG
SCL
1
2
3
4
5
10
9
V
DD
OUTœ
GND
SDA
8
IN/TRIG
EN
7
OUT+
VDD/NC
6
Not to scale
Pin Functions
PIN
TYPE(1)
DESCRIPTION
NO.
1
NAME
REG
SCL
O
I
The REG pin is the 1.8-V regulator output. A 1-µF capacitor required
2
I2C clock
I2C data
3
SDA
I/O
Multi-mode Input. I2C is selectable as PWM, analog, or trigger. If not used, this pin should
be connected to GND
4
IN/TRIG
I
5
EN
VDD/NC
OUT+
GND
I
Device enable
6
P
O
P
O
P
Optional supply input. This pin should be tied to VDD or left floating.
Positive haptic driver differential output
Supply ground
7
8
9
OUT–
VDD
Negative haptic driver differential output
Supply Input (2 V to 5.2 V). A 1-µF capacitor is required.
10
(1) I = input, O = output, I/O = input and output, P = power
4
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range, TA = 25°C (unless otherwise noted)
MIN
–0.3
–0.3
–0.3
–0.3
–0.3
–40
MAX
5.5
UNIT
V
VDD
EN
VDD + 0.3
VDD + 0.3
VDD + 0.3
VDD + 0.3
85
V
Input voltage
SDA
V
SCL
V
IN/TRIG
V
Operating free-air temperature, TA
Operating junction temperature, TJ
Storage temperature, Tstg
°C
°C
°C
–40
150
–65
150
6.2 ESD Ratings
VALUE UNIT
9-PIN DSBGA PACKAGE
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
Charged device model (CDM), per JEDEC specification JESD22-C101, all pins(2)
±1000
V
Electrostatic
discharge
V(ESD)
±250
10-PIN VSSOP PACKAGE
OUT+, OUT– pins(3)
Other pins(1)
Charged device model (CDM), per JEDEC specification JESD22-C101, all pins(2)
±500
Human body model (HBM), per
ANSI/ESDA/JEDEC JS-001
Electrostatic
V(ESD)
±1000
±250
V
discharge
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Pins listed as ±1000
V may actually have higher performance.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Pins listed as ±250 V
may actually have higher performance.
(3) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
2
MAX
5.2
UNIT
V
VDD
Supply voltage
VDD
ƒ(PWM)
ZL
PWM input frequency(1)
Load impedance(1)
IN/TRIG Pin
10
8
250
kHz
Ω
VDD = 5.2 V
VIL
Digital low-level input voltage
Digital high-level input voltage
Input voltage (analog mode)
LRA Frequency Range(1)
EN, IN/TRIG, SDA, SCL
EN, IN/TRIG, SDA, SCL
IN/TRIG
0.5
V
VIH
1.3
0
V
VI(ANA)
ƒ(LRA)
1.8
V
125
300
Hz
(1) Ensured by design. Not production tested.
6.4 Thermal Information
DRV2604L
YZF (DSBGA)
(9-PINS)
145.2
THERMAL METRIC(1)
UNIT
RθJA
RθJC(top)
RθJB
φJT
Junction-to-ambient thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
0.9
105
Junction-to-top characterization parameter
Junction-to-board characterization parameter
5.1
φJB
103.3
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Copyright © 2014–2018, Texas Instruments Incorporated
5
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
6.5 Electrical Characteristics
TA = 25°C, VDD = 3.6 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
V(REG)
IIL
Voltage at the REG pin
1.83
V
EN, IN/TRIG, SDA, SCL
VDD = 5.2 V , VI = 0 V
Digital low-level input current
1
1
µA
µA
IN/TRIG, SDA, SCL
VDD = 5.2 V, VI = VDD
IIH
Digital high-level input current
EN
3.5
0.4
VDD = 5.2 V, VI = VDD
VOL
Digital low-level output voltage
Digital pull-down resistance
SDAIOL= 4 mA
V
EN
R(EN-GND)
2
MΩ
VDD = 5.2 V , VI = VDD
I(SD)
II(standby)
IQ
Shutdown current
Standby current
Quiescent current
Input impedance
V(EN) = 0 V
4
4.1
7
7
µA
µA
mA
kΩ
V(EN) = 1.8 V, STANDBY = 1
V(EN) = 1.8 V, STANDBY = 0, no signal
IN/TRIG to V(CM_ANA)
0.5
0.65
ZI
100
IN/TRIG common-mode voltage
(AC-coupled)
V(CM_ANA)
ZO(SD)
AC_COUPLE = 1
0.9
15
4
V
kΩ
Ω
Output impedance in shutdown
OUT+ to GND, OUT– to GND
OUT+ to GND, OUT– to GND
Load impedance threshold for
over-current detection
ZL(th)
Duty cycle = 90%, LRA mode, no load
Duty cycle = 90%, ERM mode, no load
2.4
2.3
3.5
3.5
Average battery current during
operation
I(BAT_AV)
mA
6.6 Timing Requirements
TA = 25°C, VDD = 3.6 V (unless otherwise noted)
MIN
NOM
MAX
UNIT
kHz
µs
ƒ(SCL)
tw(H)
tw(L)
Frequency at the SCL pin with no wait states
Pulse duration, SCL high
400
0.6
1.3
100
10
Pulse duration, SCL low
µs
See Figure 1.
See Figure 2.
tsu(1)
th(1)
Setup time, SDA to SCL
ns
Hold time, SCL to SDA
ns
Bus free time between stop and start
condition
t(BUF)
1.3
µs
tsu(2)
th(2)
Setup time, SCL to start condition
Hold time, start condition to SCL
Setup time, SCL to stop condition
0.6
0.6
0.6
µs
µs
µs
tsu(3)
6.7 Switching Characteristics
TA = 25°C, VDD = 3.6 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
ms
Time from the GO bit or external trigger
command to output signal
0.7
t(start)
Start-up time
Time from EN high to output signal
(PWM/Analog Modes)
1.5
ƒO(PWM)
PWM Output Frequency
19.5
20.5
21.5
kHz
6
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
t
t
w(L)
w(H)
SCL
SDA
t
su(1)
t
h(1)
Figure 1. SCL and SDA Timing
SCL
SDA
t
t
t
su(3)
h(2)
su(2)
t
(BUF)
Start Condition
Stop Condition
Figure 2. Timing for Start and Stop Conditions
Copyright © 2014–2018, Texas Instruments Incorporated
7
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
6.8 Typical Characteristics
IN/TRIG
IN/TRIG
Acceleration
Acceleration
[OUT+] − [OUT−] (Filtered)
[OUT+] − [OUT−] (Filtered)
0
40m
80m
120m
Time (s)
160m
200m
0
40m
80m
120m
Time (s)
160m
200m
VDD = 4.2 V
ERM closed loop
VDD = 4.2 V
LRA closed loop
External edge trigger
External level trigger
Figure 3. ERM Click with and without Braking (RAM)
Figure 4. LRA Click With and WIthout Braking (RAM)
SDA
SDA
Acceleration
Acceleration
[OUT+] − [OUT−] (Filtered)
[OUT+] − [OUT−] (Filtered)
0
200m
400m
600m
800m
1
0
200m
400m
600m
800m
1
Time (s)
Time (s)
VDD = 4.2 V
ERM closed loop
Internal trigger
VDD = 4.2 V
ERM closed loop
Internal trigger
Figure 5. ERM Click-Bounce (RAM)
Figure 6. LRA Transition-Click (RAM)
EN
EN
SDA
IN/TRIG
Acceleration
Acceleration
[OUT+] − [OUT−] (Filtered)
[OUT+] − [OUT−] (Filtered)
0
40m
80m
120m
Time (s)
160m
200m
0
40m
80m
120m
Time (s)
160m
200m
VDD = 4.2 V
ERM open loop
RTP Mode
VDD = 3.6 V
LRA closed loop
PWM Mode
Figure 8. LRA Click With and Without Braking (PWM)
Figure 7. ERM Buzz (RTP)
8
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
Typical Characteristics (continued)
100
90
80
70
60
50
ERM mode, RL = 10 W + 100 µH, 1.3 V
ERM mode, RL = 25 W + 100 µH, 2 V(RMS)
SDA
ERM Mode
LRA Mode
0
1m
2m
3m
4m
5m
6m
7m
8m
9m 10m
2
2.4
2.8
3.2
3.6
4
4.4
4.8
5.2
Supply Voltage (V)
Time (s)
D013
VDD = 4.2 V
Closed loop
No filter
Figure 10. Supply Current vs Supply Voltage (Full Vibration)
Figure 9. Startup Latency for ERM and LRA
7 Parameter Measurement Information
7.1 Test Setup for Graphs
To capture the graphs displayed in the Typical Characteristics section, the following first-order RC-filter setup
was used with the exception of the waveform in Figure 9 which was captured without any output filter. This filter
is recommended when viewing output signals on an oscilloscope because output PWM modulation is present in
all modes. Ensure that effective impedance of the filter is not too low because the closed-loop and auto
resonance-tracking features can be affected. Therefore, TI recommends that this exact filter be used for output
measurement. Most oscilloscopes have an input impedance of 1 MΩ on each channel and therefore have an
approximately 1% loss in measured amplitude because of the voltage-divider effect with the filter.
100 kꢀ
OUT+
LRA
or
ERM
Ch1
Ch2
470 pF
470 pF
M
Ch1 œ Ch2
(Differential)
100 kꢀ
OUTœ
Oscilloscope
Figure 11. Test Setup
7.1.1 Default Test Conditions
•
•
VDD = 3.6 V, unless otherwise noted.
Real actuators (as opposed to modeled actuators) were used as loads for both ERM and LRA modes with
exception of the Supply Voltage vs Supply Current (Full Vibration) waveform in Figure 10, which used passive
RL (resistance in series with an inductance) loads for test repeatability. Real actuators vary widely in supply
currents because of variation in back-EMF voltages. Because real actuators have back EMF, the real supply
current is generally less than what is shown in the waveform because of the reduction in the apparent load
impedance. Therefore, the curve shows the worst-case current.
•
•
All traces are 2 V/div except for the accelerometer traces
All accelerometer traces are 0.87 g/div except for the LRA Click with and without Braking (PWM) curve in
Figure 8, which is 1.74 g/div.
Copyright © 2014–2018, Texas Instruments Incorporated
9
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
8 Detailed Description
8.1 Overview
The DRV2604L device is a low-voltage haptic driver that relies on the back-EMF produced by an actuator to
provide a closed-loop system that offers extremely flexible control of LRA and ERM actuators over a shared I2C-
compatible bus or PWM input signal. This schema helps improve actuator performance in terms of acceleration
consistency, start time, and brake time.
The improved smart-loop architecture inside the DRV2604L device provides effortless auto-resonant drive for
LRA, as well as feedback-optimized ERM drive allowing for automatic overdrive and braking. These features
create a simplified input waveform paradigm as well as reliable motor control and consistent motor performance.
The DRV2604L device also features an automatic transition to open-loop operation in the event that an LRA
actuator is not generating a valid back-EMF voltage and automatic synchronization with the LRA when the LRA
is generating a valid back-EMF voltage. The DRV2604L device also allows for open-loop driving by using
internally-generated PWM.
The DRV2604L device includes enough integrated RAM to allow the user to preload over 100 customized
waveforms. The waveforms can be instantly played back through an I2C or can be triggered through a hardware
trigger pin. Additionally, the real-time playback mode allows the host processor to bypass the memory playback
engine and play waveforms directly from the host through the I2C.
The DRV2604L device features a trinary-modulated output stage that provides more efficiency than linear-based
output drivers.
8.2 Functional Block Diagram
V
DD
RAM
OUT+
Supply
correction
Gate
drive
2
SDA
SCL
I C I/F
LRA
or
ERM
Control and
playback engine
Back-EMF
detection
M
EN
IN/TRIG
REG
REG
OUTt
Gate
drive
GND
10
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
8.3 Feature Description
8.3.1 Support for ERM and LRA Actuators
The DRV2604L device supports both ERM and LRA actuators. The ERM_LRA bit in register 0x1A must be
configured to select the type of actuator that the device uses.
8.3.2 Smart-Loop Architecture
The smart-loop architecture is an advanced closed-loop system that optimizes the performance of the actuator
and allows for failure detection. The architecture consists of automatic resonance tracking and reporting (for an
LRA), automatic level calibration, accelerated startup and braking, diagnostics routines, and other proprietary
algorithms.
8.3.2.1 Auto-Resonance Engine for LRA
The DRV2604L auto-resonance engine tracks the resonant frequency of an LRA in real time, effectively locking
onto the resonance frequency after half of a cycle. If the resonant frequency shifts in the middle of a waveform
for any reason, the engine tracks the frequency from cycle to cycle. The auto-resonance engine accomplishes
the tracking by constantly monitoring the back-EMF of the actuator. The auto-resonance engine is not affected by
the auto calibration process, which is only used for level calibration. No calibration is required for the auto
resonance engine. See the Auto-Resonance Engine Programming for the LRA section for auto-resonance engine
programming information.
8.3.2.2 Real-Time Resonance-Frequency Reporting for LRA
The smart-loop architecture makes the resonant frequency of the LRA available through I2C (see the LRA
Resonance Period (Address: 0x22) section). Because frequency reporting occurs in real time, the frequency
must be polled while the DRV2604L device synchronizes with the LRA. The data should not be polled when the
actuator is idle or braking.
8.3.2.3 Automatic Switch to Open-Loop for LRA
In the event that an LRA produces a non-valid back-EMF signal, the DRV2604L device automatically switches to
open-loop operation and continues to deliver energy to the actuator in overdrive mode at a default and
configurable frequency. Use Equation 1 to calculate the default frequency. If the LRA begins to produce a valid
back-EMF signal, the auto-resonance engine automatically takes control and continues to track the resonant
frequency in real time. When synchronized, the mode enjoys all of the benefits that the smart-loop architecture
has to offer.
1
ƒ(LRA_NO-BEMF)
ö
2 ì t(DRIVE_TIME[4:0]) œ t(ZC_DET _ TIME[1:0])
(1)
The DRV2604L device offers an automatic transition to open-loop mode without the re-synchronization option.
The feature is enabled by setting the LRA_AUTO_OPEN_LOOP bit in register 0x1F. The transition to open-loop
mode only occurs when the driver fails to synchronize with the LRA. The AUTO_OL_CNT[1:0] bit in register 0x1F
can be adjusted to set the amount of non-synchronized cycles allowed before the transition to the open-loop
mode. Use Equation 2 to calculate the open-loop frequency. The open-loop mode does not receive benefits from
the smart-loop architecture, such as automatic overdrive and braking.
1
ƒ(LRA_OL)
=
OL_LRA_PERIOD[6:0] × 98.49 × 10œ6
(2)
8.3.2.4 Automatic Overdrive and Braking
A key feature of the DRV2604L is the smart-loop architecture which employs actuator feedback control for both
ERMs and LRAs. The feedback control desensitizes the input waveform from the motor-response behavior by
providing automatic overdrive and automatic braking.
Copyright © 2014–2018, Texas Instruments Incorporated
11
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
Feature Description (continued)
An open-loop haptic system typically drives an overdrive voltage at startup that is higher than the steady-state
rated voltage of the actuator to decrease the startup latency of the actuator. Likewise, a braking algorithm must
be employed for effective braking. When using an open-loop driver, these behaviors must be contained in the
input waveform data. Figure 12 shows how two different ERMs with different startup behaviors (Motor A and
Motor B) can both be driven optimally by the smart-loop architecture with a simple input for both motors. The
smart-loop architecture works equally well for LRAs with a combination of feedback control and an auto-
resonance engine.
Ideal Open-Loop Waveform for Motor B
Ideal Open-Loop Waveform for Motor A
Same simple input for
both motors
Input and output
Accleration
Feedback provides
optimum output drive
Output with feedback
Figure 12. Waveform Simplification With Smart Loop
8.3.2.4.1 Startup Boost
To reduce the actuator start-time performance, the DRV2604L device has an overdrive boost feature that applies
higher loop gain to transient response of the actuator. The STARTUP_BOOST bit enables the feature.
8.3.2.4.2 Brake Factor
To reduce the actuator brake-time performance, the DRV2604L device provides a means to increase the gain
ratio between braking and driving gain. Higher feedback-gain ratios reduce the brake time, however, the gain
ratios also reduce the stability of the closed-loop system. The FB_BRAKE_FACTOR[2:0] bits can be adjusted to
set the brake factor.
8.3.2.4.3 Brake Stabilizer
To improve brake stability at high brake-factor gain ratios, the DRV2604L device has a brake-stabilizer
mechanism that automatically reduces the loop gain when the braking is near completion. The
BRAKE_STABILIZER bit enables the feature.
12
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
Feature Description (continued)
8.3.2.5 Automatic Level Calibration
The smart-loop architecture uses actuator feedback by monitoring the back-EMF behavior of the actuator. The
level of back-EMF voltage can vary across actuator manufacturers because of the specific actuator construction.
Auto calibration compensates for the variation and also performs scaling for the desired actuator according to the
specified rated voltage and overdrive clamp-register settings. When auto calibration is performed, a 100% signal
level at any of the DRV2604L input interfaces supplies the rated voltage to the actuator at steady-state. The
feedback allows the output level to increase above the rated voltage level for automatic overdrive and braking,
but without allowing the output level to exceed the programmable overdrive clamp voltage.
In the event where the automatic level-calibration routine fails, the DIAG_RESULT bit in register 0x00 is asserted
to flag the problem. Calibration failures are typically fixed by adjusting the registers associated with the automatic
level-calibration routine or, for LRA actuators, the registers associated with the automatic-resonance detection
engine. See the 器件和文档支持 section for automatic-level calibration programming.
8.3.2.5.1 Automatic Compensation for Resistive Losses
The DRV2604L device automatically compensates for resistive losses in the driver. During the automatic level-
calibration routine, the impedance of the actuator is checked and the compensation factor is determined and
stored in the A_CAL_COMP[7:0] bit.
8.3.2.5.2 Automatic Back-EMF Normalization
The DRV2604L device automatically compensates for differences in back-EMF magnitude between actuators.
The compensation factor is determined during the automatic level-calibration routine and the factor is stored in
the A_CAL_BEMF[7:0] bit.
8.3.2.5.3 Calibration Time Adjustment
The duration of the automatic level-calibration routine has an impact on accuracy. The impact is highly
dependent on the start-time characteristic of the actuator. The auto-calibration routine expects the actuator to
have reached a steady acceleration before the calibration factors are calculated. Because the start-time
characteristic can be different for each actuator, the AUTO_CAL_TIME[1:0] bit can change the duration of the
automatic level-calibration routine to optimize calibration performance.
8.3.2.5.4 Loop-Gain Control
The DRV2604L device allows the user to control how fast the driver attempts to match the back-EMF (and thus
motor velocity) and the input signal level. Higher loop-gain (or faster settling) options result in less-stable
operation than lower loop gain (or slower settling). The LOOP_GAIN[1:0] bit controls the loop gain.
8.3.2.5.5 Back-EMF Gain Control
The BEMF_GAIN[1:0] bit sets the analog gain for the back-EMF amplifier. The auto-calibration routine
automatically populates the bit with the most appropriate value for the actuator.
Modifying the SAMPLE_TIME[1:0] bit also adjusts the back-EMF gain. The higher the sample time, the higher
the gain.
By default, the back-EMF is sampled once during a period. In the event that a twice per-period sampling is
desired, assert the LRA_DRIVE_MODE bit.
8.3.2.6 Actuator Diagnostics
The DRV2604L device is capable of determining whether the actuator is not present (open) or shorted. If a fault
is detected during the diagnostic process, the DIAG_RESULT bit is asserted.
8.3.2.7 Automatic Re-Synchronization
For the LRA, the DRV2604L device features an automatic re-synchronization mode which automatically pushes
the actuator in the correct direction when a waveform begins playing while the actuator is moving. If the actuator
is at rest when the waveform begins, the DRV2604L device drives in the default direction.
Copyright © 2014–2018, Texas Instruments Incorporated
13
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
Feature Description (continued)
8.3.3 Open-Loop Operation for LRA
In the event that open-loop operation is desired (such as for off-resonance driving) the DRV2604L device
includes an open-loop LRA drive mode that is available through the PWM input or through the digital interface.
When using the PWM input in open-loop mode, the DRV2604L device employs a fixed divider that observes the
PWM signal and commutates the output drive signal at the PWM frequency divided by 128. To accomplish LRA
drive, the host should drive the PWM frequency at 128 times the desired operating frequency.
When activated, the digital open-loop mode is available for pre-stored waveforms as well as for RTP mode. The
OL_LRA_PERIOD bit in register 0x20 programs the operating frequency, which is derived from the PWM output
frequency, ƒO(PWM). Use Equation 1 to calculate the driving frequency. The open-loop mode does not receive the
benefits of the smart-loop architecture.
8.3.4 Open-Loop Operation for ERM
The DRV2604L device offers ERM open-loop operation through the PWM input. The output voltage is based on
the duty cycle of the provided PWM signal, where the OD_CLAMP[7:0] bit in register 0x17 sets the full-scale
amplitude. For details see the Rated Voltage Programming section.
8.3.5 Flexible Front-End Interface
The DRV2604L device offers multiple ways to launch and control haptic effects. The MODE[2:0] bit in register
0x01 is used to select the interface mode.
8.3.5.1 PWM Interface
When the DRV2604L device is in PWM interface mode, the device accepts PWM data at the IN/TRIG pin. The
DRV2604L device drives the actuator continuously in PWM interface mode until the user sets the device to
standby mode or to enter another interface mode. In standby mode, the strength of vibration is determined by the
duty cycle.
For the LRA, the DRV2604L device automatically tracks the resonance frequency unless the LRA_OPEN_LOOP
bit in register 0x1D is set. If the LRA_OPEN_LOOP bit is set, the LRA is driven according to the frequency of the
PWM input signal. Specifically, the driving frequency is the PWM frequency divided by 128.
8.3.5.2 Internal Memory Interface
The DRV2604LL device is designed with 2 kB of integrated RAM for waveform storage used by the playback
engine. The data is stored in an efficient way (voltage-time pairs) to maximize the number of waveforms that can
be carried. The playback engine also has the ability to generate smooth ramps (up or down) by relying on the
start-waveform and end-waveform points and by using linear interpolation techniques.
Storing waveforms on the DRV2604LL device instead of the host processor has several advantages including:
•
•
•
Offloading processing requirements, such as PWM generation, from the host processor or micro-controller
Improving latency by storing the waveforms on the DRV2604LL device and only requiring a trigger signal
Reducing I2C traffic by eliminating the requirement to transfer waveform data
8.3.5.2.1 Waveform Sequencer
The waveform sequencer queues waveform identifiers for playback. Eight sequence registers queue up to eight
waveforms for sequential playback. A waveform identifier is an integer value referring to the index position of a
waveform in the RAM library. Playback begins at register address 0x04 when the user asserts the GO bit
(register 0x0C). When playback of that waveform ends, the waveform sequencer plays the waveform identifier
held in register 0x05 if the next waveform is non-zero. The waveform sequencer continues in this way until it
reaches an identifier value of zero or until all eight identifiers are played (register addresses 0x04 through 0x0B),
whichever scenario is reached first.
The waveform identifier range is 1 to 127. The MSB of each sequence register can implement a delay between
sequence waveforms. When the MSB is high, bits [6:0] indicate the length of the wait time. The wait time for that
step then becomes WAV_FRM_SEQ[6:0] × 10 ms.
14
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
Feature Description (continued)
8.3.5.2.2 Library Parameterization
The RAM waveforms are augmented by the time offset registers (registers 0x0D to 0x10). The augmentation
occurs only for the RAM waveforms and not for the other interfaces (such as PWM and RTP). The purpose of
the functionality is to add time stretching (or time shrinking) to the waveform. This functionality is useful for
customizing the entire library of waveforms for a specific actuator rise time and fall time.
The time parameters that can be stretched or shrunk include:
ODT
SPT
SNT
BRT
Overdrive time
Sustain positive time
Sustain Negative Time
Brake Time
The time values are additive offsets and are 8-bit signed values. The default offset of the time values is 0.
Positive values add and negative values subtract from the time value of the effect that is currently played. The
most positive value in the waveform is automatically interpreted as the overdrive time, and the most negative
value in the waveform is automatically interpreted as the brake time. The time-offset parameters are applied to
both voltage-time pairs and linear ramps. For linear ramps, linear interpolation is stretched (or shrunk) over the
two operative points for the period (see Equation 3).
t + t(ofs)
where
•
t(ofs) is the time offset
(3)
Changing the playback interval can also manipulate the waveforms stored in memory. Each waveform in memory
has a granularity of 5 ms. If the user desires greater granularity, a 1-ms playback interval can be obtained by
asserting the PLAYBACK_INTERVAL bit in register 0x1F.
8.3.5.3 Real-Time Playback (RTP) Interface
The real-time playback mode is a simple, single 8-bit register interface that holds an amplitude value. When real-
time playback is enabled, the real-time playback register is sent directly to the playback engine. The amplitude
value is played until the user sends the device to standby mode or removes the device from RTP mode. The
RTP mode operates exactly like the PWM mode except that the user enters a register value over the I2C rather
than a duty cycle through the input pin. Therefore, any API (application-programming interface) designed for use
with a PWM generator in the host processor can write the data values over the I2C rather than writing the data
values to the host timer. This ability frees a timer in the host while retaining compatibility with the original
software.
For the LRA, the DRV2604L device automatically tracks the resonance frequency unless the LRA_OPEN_LOOP
bit is set (in register 0x1D). If the LRA_OPEN_LOOP bit is set, the LRA is driven according to the open-loop
frequency set in the OL_LRA_PERIOD[6:0] bit in register 0x20.
8.3.5.4 Analog Input Interface
When the DRV2604L device is in analog-input interface mode, the device accepts an analog voltage at the
IN/TRIG pin. The DRV2604L device drives the actuator continuously in analog-input interface mode until the user
sets the device to standby mode or to enter another interface mode. The reference voltage in standby mode is
1.8 V. Therefore, the 1.8-V reference voltage is interpreted as a 100% input value. A reference voltage of 0.9 V
is interpreted as a 50% input value and a reference voltage of 0 V is interpreted as a 0% input value. The input
value in standby mode is analogous to the duty-cycle percentage in PWM mode.
For the LRA, the DRV2604L automatically tracks the resonance frequency unless the LRA_OPEN_LOOP bit is
set (in register 0x1D). If the LRA_OPEN_LOOP bit is set, the LRA is driven according to the open-loop frequency
set in OL_LRA_PERIOD[6:0] bit in register 0x20.
Copyright © 2014–2018, Texas Instruments Incorporated
15
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
Feature Description (continued)
8.3.5.5 Input Trigger Option
The DRV2604L device includes continuous haptic modes (such as PWM and RTP mode) as well as triggered
modes (such as the internal memory interface). The haptic effects in the continuous haptic modes begin as soon
as the device enters the mode and stop when the device goes into standby mode or exits the continuous haptic
mode. For the triggered mode, the DRV2604L device has a variety of trigger options that are explained in this
section.
In the continuous haptic modes, the IN/TRIG pin provides external trigger control of the GO bit, which allows
GPIO control to fire RAM waveforms. The external trigger control can provide improved latencies in systems
where a significant delay exists between the desired effect time and the time a GO command can be sent over
the I2C interface.
NOTE
The triggered effect must already be selected to take advantage of the lower latency. This
option works best for accelerating a pre-queued high-priority effect (such as a button
press) or for the repeated firing of the same effect (such as scrolling).
8.3.5.5.1 I2C Trigger
Setting the GO bit (in register 0x0C) launches the waveform. The user can cancel the launching of the waveform
by clearing the GO bit.
8.3.5.5.2 Edge Trigger
A low-to-high transition on the IN/TRIG pin sets the GO bit. The playback sequence indicated in the waveform
sequencer plays as normal. The user can cancel the transaction by clearing the GO bit. An additional low-to-high
transition while the GO bit is high also cancels the transaction which clears and resets the GO bit. Clearing the
trigger pin (high-to-low transition) does nothing, therefore the user can send a short pulse without knowing how
long the waveform is. The pulse width should be at least 1 µs to ensure detection.
Edge Trigger
Haptic Waveform
Edge Trigger
Cancellation
Haptic Waveform
Figure 13. Edge Trigger Mode
8.3.5.5.3 Level Trigger
The actions of the GO bit directly follow the IN/TRIG pin. When the IN/TRIG pin is high, the GO bit is high. When
the IN/TRIG pin goes low, the GO bit clears. Therefore, a falling edge cancels the transaction. The level trigger
can implement a GPIO-controlled buzz on-off controller if an appropriately long waveform is selected. The user
must hold the IN/TRIG high for the entire duration of the waveform to complete the effect.
16
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
Feature Description (continued)
Level Trigger
Haptic Waveform
Level Trigger
Cancellation
Haptic Waveform
Figure 14. Level Trigger Mode
8.3.5.6 Noise Gate Control
When an actuator is driven with an analog or PWM signal, noise in the line can cause the actuator to vibrate
unintentionally. For that reason, the DRV2604L device features a noise gate that filters out any voltage smaller
than a particular threshold. The NG_THRESH[1:0] bit in register 0x1D controls the threshold.
8.3.6 Edge Rate Control
The DRV2604L output driver implements edge rate control (ERC). The ERC ensures that the rise and fall
characteristics of the output drivers do not emit levels of radiation that could interfere with other circuitry common
in mobile and portable platforms. Because of ERC most system do not require external output filters, capacitors,
or ferrite beads.
8.3.7 Constant Vibration Strength
The DRV2604L PWM input uses a digital level-shifter. Therefore, as long as the input voltage meets the VIH and
VIL levels, the vibration strength remains the same even if the digital levels vary. The DRV2604L device also
features power-supply feedback. If the supply voltage drifts over time (because of battery discharge, for
example), the vibration strength remains the same as long as enough supply voltage is available to sustain the
required output voltage.
8.3.8 Battery Voltage Reporting
During playback, the DRV2604L device provides real-time voltage measurement of the VDD pin. The VBAT[7:0]
bit located in register 0x21 provides this information.
8.3.9 One-Time Programmable (OTP) Memory for Configuration
The DRV2604L device contains nonvolatile, on-chip, OTP memory for specific configuration parameters. When
written, the DRV2604L device retains the device settings in registers 0x16 through 0x1A including after power
cycling. This retention allows the user to account for small variations in actuator manufacturing from unit to unit
as well as to shorten the device-initialization process for device-specific parameters such as actuator type,
actuator-rated voltage, and other parameters. An additional benefit of OTP is that the DRV2604L memory can be
customized at the device-test level without driving changes in the device software.
8.3.10 Low-Power Standby
Setting the device to standby reduces the idle power consumption without resetting the registers. In Low-Power
Standby mode, the DRV2604L device features a fast turnon time when it is requested to play a waveform.
Copyright © 2014–2018, Texas Instruments Incorporated
17
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
Feature Description (continued)
8.3.11 I2C Watchdog Timer
If an I2C stops unexpectedly, the possibility exists for the I2C protocol to remain in a hanged state. To allow for
the recovery of the communication without having to power cycle the device, the DRV2604L device includes an
automatic watchdog timer that resets the I2C protocol without user intervention after 4.33 ms. This behavior
happens in all conditions except in standby mode. If the I2C stops unexpectedly during standby mode, the only
way to recover communication is by power-cycling the device.
8.3.12 Device Protection
8.3.12.1 Thermal Protection
The DRV2604L device has thermal protection that causes the device to shut down if it becomes too hot. In the
event where the thermal protection kicks in, the DRV2604L device asserts a flag (bit OVER_TEMP in register
0x00) to notify the host processor.
8.3.12.2 Overcurrent Protection of the Actuator
If the impedance at the output pin of the DRV2604L device is too low, the device latches the over-current flag
(OC_DETECT bit in register 0x00) and shuts down. The device periodically monitors the status of the short and
remains in this condition until the short is removed. When the short is removed, the DRV2604L device restarts in
the default state.
8.3.12.3 Overcurrent Protection of the Regulator
The DRV2604L device has an internal regulator that powers a portion of the system. If a short occurs at the
output of the REG pin, an internal overcurrent protection circuit is enabled and limits the current.
During a REG short, the device is not functional. When the short is removed, the DRV2604L device automatically
resets to default conditions.
8.3.12.4 Brownout Protection
The DRV2604L device has on-chip brownout protection. When activated, a reset signal is issued that returns the
DRV2604L device to the initial default state. If the regulator voltage V(REG) goes below the brownout protection
threshold (V(BOT)) the DRV2604L device automatically shuts down. When V(REG) returns to the typical output
voltage (1.8 V) the DRV2604L device returns to the initial device state. The brownout protection threshold
(V(BOT)) is typically at 0.84 V.
The previously described behavior has one exception. The brownout circuit is designed to tolerate fast brownout
conditions as shown by Case 1 in Figure 15. If the VDD ramp-up rate is slower than 3.6 kV/s, then the device can
fall into an unknown state. In such a situation, to return to the initial default state the device must be power-
cycled with a VDD ramp-up rate that is faster than 3.6 kV/s.
Case 1
Case 3
Case 4
Case 2
V
V
DD
DD
Return to
default
state
Return to
default
state
Unknown
state
Unknown
state
2 V
1.8 V
REG
Time
V
(BOT)
0 V
Slew rate > 3.6 kV/s
Slew rate < 3.6 kV/s
Slew rate < 3.6 kV/s
Slew rate > 3.6 kV/s
Figure 15. Brownout Behavior
18
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
8.4 Device Functional Modes
8.4.1 Power States
The DRV2604L device has three different power states which allow for different power-consumption levels and
functions. Figure 16 shows the transition in to and out of each state.
EN = 0
EN = 1
Shutdown
Standby
STANDBY = 0
EN = 0
STANDBY = 1
Active
DEV_RESET = 1
Figure 16. Power-State Transition Diagram
8.4.1.1 Operation With VDD < 2 V (Minimum VDD
)
Operating the device with a VDD value below 2 V is not recommended.
8.4.1.2 Operation With VDD > 5.5 V (Absolute Maximum VDD
)
The DRV2604L device is designed to operate at up to 5.2 V, with an absolute maximum voltage of 5.5 V. If
exposed to voltages above 5.5 V, the device can suffer permanent damage.
8.4.1.3 Operation With EN Control
The EN pin of the DRV2604L device gates the active operation. When the EN pin is logic high, the DRV2604L
device is active. When the EN pin is logic low, the device enters the shutdown state, which is the lowest power
state of the device. The device registers are not reset. The EN pin operation is particularly useful for constant-
source PWM and analog input modes to maintain compatibility with non-I2C device signaling. The EN pin must
be high to write I2C device registers. However, if the EN pin is low the DRV2604L device can still acknowledge
(ACK) during an I2C transaction, however, no read or write is possible. To completely reset the device to the
powerup state, set the DEV_RESET bit in register 0x01.
8.4.1.4 Operation With STANDBY Control
The STANDBY bit in register 0x01 forces the device in an out of the standby state. The STANDBY bit is asserted
by default. When the STANDBY bit is asserted, the DRV2604L device goes into a low-power state. In the
standby state the device retains register values and the ability to have I2C communication. The properties of the
standby state also feature a fast turn, wake up, and play, on-time. Asserting the STANDBY bit has an immediate
effect. For example, if a waveform is played, it immediately stops when the STANDBY bit is asserted.
Clear the STANDBY bit to exit the standby state (and go to the ready state).
8.4.1.5 Operation With DEV_RESET Control
The DEV_RESET bit in register 0x01 performs the equivalent of power cycling the device. Any playback
operations are immediately interrupted, and all registers are reset to the default values. The Dev_Reset bit
automatically-clears after the reset operation is complete.
Copyright © 2014–2018, Texas Instruments Incorporated
19
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
Device Functional Modes (continued)
8.4.1.6 Operation in the Active State
In the active state, the DRV2604L device has I2C communication and is capable of playing waveforms, running
calibration, and running diagnostics. These operations are referred to as processes. Figure 17 shows the flow of
starting, or firing, a process. Notice that the GO signal fires the processes. Note that the GO signal is not the
same as the GO bit. Figure 18 shows a diagram of the GO-signal behavior.
Change
Modes
Ready
GO Signal = 1
Process
Done
GO Signal = 1
Optional
Check for
Output
Shorts
Wait 1 s
Run
Process
No Short
Short Found
Short Found
Note: If an output short is present before a waveform is played, changing modes (with the MODE[2:0] bit in register 0x01) is
required to resume normal playback.
Figure 17. Diagram of Active States
8.4.2 Changing Modes of Operation
The DRV2604L has multiple modes for playing waveforms, as well as a calibration mode and a diagnostic mode.
Table 1 lists the available modes.
Table 1. Mode Selection Table
MODE
Internal trigger mode
External Trigger mode (edge)
External trigger mode (level)
Analog input mode
PWM mode
MODE[2:0]
N_PWM_ANALOG
0
1
2
3
3
5
6
7
X
X
X
0
1
RTP mode
X
X
X
Diagnostics mode
Calibration mode
8.4.3 Operation of the GO Bit
The GO bit is the primary way to assert the GO signal, which fires processes in the DRV2604L device. The
primary purpose of the GO bit is to fire the playback of the waveform identifiers in the waveform sequencer
(registers 0x04 to 0x0B). However, The GO bit can also fire the calibration or diagnostics processes.
When using the GO bit to play waveforms in internal trigger mode, the GO bit is asserted by writing 0x01 to
register 0x0C. In this case, the GO bit can be thought of as a software trigger for haptic waveforms. The GO bit
remains high until the playback of the haptic waveform sequence is complete. Clearing the GO bit during
waveform playback cancels the waveform sequence. The GO bit can also be asserted by the external trigger
when in external trigger mode. The GO bit in register 0x0C mirrors the state of the external trigger.
Setting RTP mode or PWM mode also sets the GO bit. However, setting the GO bit in this way has no impact on
the GO bit located in register 0x0C.
20
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
Also accessible
2
(R/W) through I C
MODE[2:0] = 1 (External trigger – edge)
MODE[2:0] = 2 (External trigger – level)
IN/TRIG (Trigger)
GO Bit
GO Bit
MODE[2:0] = 3 (PWM and analog input)
MODE[2:0] = 5 (RTP mode)
GO Signal
Figure 18. GO-Signal Logic
8.4.4 Operation During Exceptional Conditions
This section lists different exceptional conditions and the ways that the DRV2604L device operates during these
conditions. This section also describes how the device goes into and out of these states.
8.4.4.1 Operation With No Actuator Attached
In LRA closed-loop mode, if a waveform is played without an actuator connected to the OUT+ and OUT– pins,
the output pins toggle. However, the toggling frequency is not predictable. In LRA open-loop mode, the output
pins toggle at the specified open-loop frequency.
8.4.4.2 Operation With a Non-Moving Actuator Attached
The model of a non-moving actuator can be simplified as a resistor. If a resistor (with similar loading as an LRA,
such as 25 O) is connected across the OUT+ and OUT– pins, and the DRV2604L device is in LRA closed-loop
mode, the output pins toggle at a default frequency calculated with Equation 1. In LRA open-loop mode the
output pins toggle at the specified open-loop frequency.
8.4.4.3 Operation With a Short at REG Pin
If the REG pin is shorted to GND, the device automatically shuts down and an overcurrent-protection circuit is
enabled and clamps the maximum current supplied by the regulator. When the short is removed, the device
starts in the default condition.
8.4.4.4 Operation With a Short at OUT+, OUT–, or Both
If any of the output pins (OUT+ or OUT–) is shorted to VDD, GND, or to each other while the device is playing a
waveform, the OC_DETECT bit is asserted and remains asserted until the short is removed. A current-protection
circuit automatically enables to shutdown the current through the short.
If the driver is playing a waveform the DRV2604L device checks for shorts in the output through either a haptic-
playback, auto-calibration, or diagnostics process. If the short occurs when the device is idle, the short is not
detected until the device attempts to run a waveform.
Copyright © 2014–2018, Texas Instruments Incorporated
21
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
8.5 Programming
8.5.1 Auto-Resonance Engine Programming for the LRA
8.5.1.1 Drive-Time Programming
The resonance frequency of each LRA actuator varies based on many factors and is generally dominated by
mechanical properties. The auto-resonance engine-tracking system is optimized by providing information about
the resonance frequency of the actuator. The DRIVE_TIME[4:0] bit is used as an initial guess for the half-period
of the LRA. The drive time is automatically and quickly adjusted for optimum drive. For example, if the LRA has a
resonance frequency of 200 Hz, then the drive time should be set to 2.5 ms.
For ERM actuators, the DRIVE_TIME[4:0] bit controls the rate for back-EMF sampling. Lower drive times imply
higher back-EMF sampling frequencies which cause higher peak-to-average ratios in the output signal, and
requires more supply headroom. Higher drive times imply lower back-EMF sampling frequencies which cause the
feedback to react at a slower rate.
8.5.1.2 Current-Dissipation Time Programming
To sense the back-EMF of the actuator, the DRV2604L device goes into high impedance mode. However, before
the device enters high impedance mode, the device must dissipate the current in the actuator. The DRV2604L
device controls the time allocated for dissipation-current through the IDISS_TIME[3:0] bit.
8.5.1.3 Blanking Time Programming
After the current in the actuator dissipates, the DRV2604L device waits for a blanking time of the signal to settle
before the back-EMF analog-to-digital (AD) conversion converts. The BLANKING_TIME[3:0] bit controls this time.
8.5.1.4 Zero-Crossing Detect-Time Programming
When the blanking time expires, the back-EMF AD monitors for zero crossings. The ZC_DET_TIME[1:0] bit
controls the minimum time allowed for detecting zero crossings.
8.5.2 Automatic-Level Calibration Programming
8.5.2.1 Rated Voltage Programming
The rated voltage is the driving voltage that the driver will output during steady state. However, in closed-loop
drive mode, temporarily having an output voltage that is higher than the rated voltage is possible. See the
Overdrive Voltage-Clamp Programming section for details.
The RATED_VOLTAGE[7:0] bit in register 0x16 sets the rated voltage for the closed-loop drive modes. For the
ERM, Equation 4 calculates the average steady-state voltage when a full-scale input signal is provided. For the
LRA, Equation 5 calculates the root-mean-square (RMS) voltage when driven to steady state with a full-scale
input signal.
V
(ERM-CL_AV)= 21.18 ×10œ3 RATED_VOLTAGE[7:0]
(4)
20.58 × 10œ3 × RATED_VOLTAGE[7:0]
1 œ (4 þ t(SAMPLE_TIME) + 300 ì 10œ6 ) þ ƒ(LRA)
V
=
(LRA-CL_RMS)
(5)
In open-loop mode, the RATED_VOLTAGE[7:0] bit is ignored. Instead, the OD_CLAMP[7:0] bit (in register 0x17)
is used to set the rated voltage for the open-loop drive modes. For the ERM, Equation 6 calculates the rated
voltage with a full-scale input signal. For the LRA, Equation 7 calculates the RMS voltage with a full-scale input
signal.
V
(ERM-OL_AV)= 21.59 × 10œ3 OD_CLAMP[7:0]
(6)
V
(LRA-OL_RMS)= 21.32 þ 10œ3 þ OD_CLAMP[7:0] þ 1 œ ƒ(LRA) þ 800 þ 10œ6
(7)
The auto-calibration routine uses the RATED_VOLTAGE[7:0] and OD_CLAMP[7:0] bits as inputs and therefore
these registers must be written before calibration is performed. Any modification of this register value should be
followed by calibration to appropriately set A_CAL_BEMF[7:0].
22
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
Programming (continued)
8.5.2.2 Overdrive Voltage-Clamp Programming
During closed-loop operation, the actuator feedback allows the output voltage go above the rated voltage during
the automatic overdrive and automatic braking periods. The OD_CLAMP[7:0] bit (in Register 0x17) sets a clamp
so that the automatic overdrive is bounded. The OD_CLAMP[7:0] bit also serves as the full-scale reference
voltage for open-loop operation. The OD_CLAMP[7:0] bit always represents the maximum peak voltage that is
allowed, regardless of the mode.
NOTE
If the supply voltage (VDD) is less than the overdrive clamp voltage, the output driver is
unable to reach the clamp voltage value because the output voltage cannot exceed the
supply voltage. If the rated voltage exceeds the overdrive clamp voltage, the overdrive
clamp voltage has priority over the rated voltage.
In ERM mode, use Equation 8 to calculate the allowed maximum voltage. In LRA mode, use Equation 9 to
calculate the maximum peak voltage.
21.64 þ 10œ3 þ OD_CLAMP[7:0] þ (t(DRIVE_TIME) œ300 þ 10œ6
)
V
=
(ERM_ clamp)
t(DRIVE_TIME) + t(IDISS_TIME) + t(BLANKING_TIME)
(8)
(9)
V
(LRA_clamp)= 21.22 × 10œ3 × OD_CLAMP[7:0]
8.5.3 I2C Interface
8.5.3.1 General I2C Operation
The I2C bus employs two signals, SDA (data) and SCL (clock), to communicate between integrated circuits in a
system. The bus transfers data serially, one bit at a time. The 8-bit address and data bytes are transferred with
the most-significant bit (MSB) first. In addition, each byte transferred on the bus is acknowledged by the receiving
device with an acknowledge bit. Each transfer operation begins with the master device driving a start condition
on the bus and ends with the master device driving a stop condition on the bus. The bus uses transitions on the
data pin (SDA) while the clock is at logic high to indicate start and stop conditions. A high-to-low transition on the
SDA signal indicates a start, and a low-to-high transition indicates a stop. Normal data-bit transitions must occur
within the low time of the clock period. Figure 19 shows a typical sequence. The master device generates the 7-
bit slave address and the read-write (R/W) bit to start communication with a slave device. The master device
then waits for an acknowledge condition. The slave device holds the SDA signal low during the acknowledge
clock period to indicate acknowledgment. When this acknowledgment occurs, the master transmits the next byte
of the sequence. Each device is addressed by a unique 7-bit slave address plus a R/W bit (1 byte). All
compatible devices share the same signals through a bidirectional bus using a wired-AND connection.
The number of bytes that can be transmitted between start and stop conditions is not limited. When the last word
transfers, the master generates a stop condition to release the bus. Figure 19 shows a generic data-transfer
sequence.
Use external pullup resistors for the SDA and SCL signals to set the logic-high level for the bus. Pullup resistors
with values between 660 Ω and 4.7 kΩ are recommended. Do not allow the SDA and SCL voltages to exceed
the DRV2604L supply voltage, VDD
.
NOTE
The DRV2604L slave address is 0x5A (7-bit), or 1011010 in binary.
Copyright © 2014–2018, Texas Instruments Incorporated
23
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
Programming (continued)
8-bit register data for address
8-bit register data for address
7-bit slave address
A
8-bit register address (N)
A
A
A
R/W
(N)
(N)
b7 b6 b5 b4 b3 b2 b1 b0
b7 b6 b5 b4 b3 b2 b1 b0
b7 b6 b5 b4 b3 b2 b1 b0
b7 b6 b5 b4 b3 b2 b1 b0
Start
Stop
Figure 19. Typical I2C Sequence
The DRV2604L device operates as an I2C-slave 1.8-V logic thresholds, but can operate up to the VDD voltage.
The device address is 0x5A (7-bit), or 1011010 in binary which is equivalent to 0xB4 (8-bit) for writing and 0xB5
(8-bit) for reading.
8.5.3.2 Single-Byte and Multiple-Byte Transfers
The serial control interface supports both single-byte and multiple-byte R/W operations for all registers.
During multiple-byte read operations, the DRV2604L device responds with data one byte at a time and beginning
at the signed register. The device responds as long as the master device continues to respond with
acknowledges.
The DRV2604L supports sequential I2C addressing. For write transactions, a sequential I2C write transaction has
taken place if a register is issued followed by data for that register as well as the remaining registers that follow.
For I2C sequential-write transactions, the register issued then serves as the starting point and the amount of data
transmitted subsequently before a stop or start is transmitted determines how many registers are written.
8.5.3.3 Single-Byte Write
As shown in Figure 20, a single-byte data-write transfer begins with the master device transmitting a start
condition followed by the I2C device address and the read-write bit. The read-write bit determines the direction of
the data transfer. For a write-data transfer, the read-write bit must be set to 0. After receiving the correct I2C
device address and the read-write bit, the DRV2604L responds with an acknowledge bit. Next, the master
transmits the register byte corresponding to the DRV2604L internal-memory address that is accessed. After
receiving the register byte, the device responds again with an acknowledge bit. Finally, the master device
transmits a stop condition to complete the single-byte data-write transfer.
Acknowledge
Acknowledge
Acknowledge
A7 A6 A5
A6 A5 A4 A3 A2 A1 A0
W
ACK
A4 A3 A2 A0 A1 ACK D7 D6 D5 D4 D3 D2 D1 D0 ACK
2
Stop
condition
Subaddress
Data byte
Start
condition
I C device address
and R/W bit
Figure 20. Single-Byte Write Transfer
24
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
Programming (continued)
8.5.3.4 Multiple-Byte Write and Incremental Multiple-Byte Write
A multiple-byte data write transfer is identical to a single-byte data write transfer except that multiple data bytes
are transmitted by the master device to the DRV2604L device as shown in Figure 21. After receiving each data
byte, the DRV2604L device responds with an acknowledge bit.
Acknowledge
Acknowledge
Acknowledge
Acknowledge
Acknowledge
A1 A0
A1 A0
W
ACK A7 A6
A1 A0 ACK D7 D6
D1 D0 ACK D7
D0 ACK D7
D0 ACK
Stop
condition
2
Start
condition
Subaddress
First data byte
Other data bytes
Last data byte
I C device address
and R/W bit
Figure 21. Multiple-Byte Write Transfer
8.5.3.5 Single-Byte Read
Figure 22 shows that a single-byte data-read transfer begins with the master device transmitting a start condition
followed by the I2C device address and the read-write bit. For the data-read transfer, both a write followed by a
read actually occur. Initially, a write occurs to transfer the address byte of the internal memory address to be
read. As a result, the read-write bit is set to 0.
After receiving the DRV2604L address and the read-write bit, the DRV2604L device responds with an
acknowledge bit. The master then sends the internal memory address byte, after which the device issues an
acknowledge bit. The master device transmits another start condition followed by the DRV2604L address and the
read-write bit again. This time, the read-write bit is set to 1, indicating a read transfer. Next, the DRV2604L
device transmits the data byte from the memory address that is read. After receiving the data byte, the master
device transmits a not-acknowledge followed by a stop condition to complete the single-byte data read transfer.
See the note in the General I2C Operation section.
Acknowledge
Acknowledge
Acknowledge
Acknowledge
ACK
ACK
ACK
A6 A5
A1 A0
W
A7 A6
A1 A0
A6 A5
A0
R
D7
D0 ACK
2
2
Start
Condition
Subaddress
Repeat start
condition
Data Byte
Stop
Condition
I C device address and
R/W bit
I C device address and
R/W bit
Figure 22. Single-Byte Read Transfer
8.5.3.6 Multiple-Byte Read
A multiple-byte data-read transfer is identical to a single-byte data-read transfer except that multiple data bytes
are transmitted by the DRV2604L device to the master device as shown in Figure 23. With the exception of the
last data byte, the master device responds with an acknowledge bit after receiving each data byte.
Acknowledge
Acknowledge
Acknowledge
Acknowledge
Acknowledge
Acknowledge
A6
A0
W
ACK A7 A6
A1 A0 ACK
A6 A5
2
A0
R
ACK D7
D0 ACK D7
D0 ACK D7
D0 ACK
2
Stop
Repeat start
Start
Subaddress
First data byte Other data byte Last data byte
I C device address
and R/W bit
I C device address
and R/W bit
condition
condition
condition
Figure 23. Multiple-Byte Read Transfer
Copyright © 2014–2018, Texas Instruments Incorporated
25
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
Programming (continued)
8.5.4 Programming for Open-Loop Operation
The DRV2604L device can be used in open-loop mode and closed-loop mode. If open-loop operation is desired,
the first step is to determine which actuator type is to use, either ERM or LRA.
8.5.4.1 Programming for ERM Open-Loop Operation
To configure the DRV2604L device in ERM open-loop operation, the ERM must be selected by writing the
N_ERM_LRA bit to 0 (in register 0x1A), and the ERM_OPEN_LOOP bit to 1 in register 0x1D.
8.5.4.2 Programming for LRA Open-Loop Operation
To configure the DRV2604L device in LRA open-loop operation, the LRA must be selected by writing the
N_ERM_LRA bit to 1 in register 0x1A, and the LRA_OPEN_LOOP bit to 1 in register 0x1D. If PWM interface is
used, the open-loop frequency is given by the PWM frequency divided by 128. If PWM interface is not used, the
open-loop frequency is given by the OL_LRA_PERIOD[6:0] bit in register 0x20.
8.5.5 Programming for Closed-Loop Operation
For closed-loop operation, the device must be calibrated according to the actuator selection. When calibrated
accordingly, the user is only required to provide the desired waveform. The DRV2604L device automatically
adjusts the level and, for the LRA, automatically adjusts the driving frequency.
8.5.6 Auto Calibration Procedure
The calibration engine requires a number of bits as inputs before the engine can be executed (see Figure 24).
When the inputs are configured, the calibration routine can be executed. After calibration execution occurs, the
output parameters are written over the specified register locations. Figure 24 shows all of the required inputs and
generated outputs. To ensure proper auto-resonance operation, the LRA actuator type requires more input
parameters than the ERM. The LRA parameters are ignored when the device is in ERM mode.
Inputs
Outputs
ERM_LRA
BEMF_GAIN[1:0]
A_CAL_COMP[7:0]
A_CAL_BEMF[7:0]
DIAG_RESULT
FB_BRAKE_FACTOR[2:0]
LOOP_GAIN[1:0]
RATED_VOLTAGE[7:0]
OD_CLAMP[7:0]
AUTO_CAL_TIME[1:0]
DRIVE_TIME[4:0]
Auto-calibration engine
SAMPLE_TIME[1:0]
BLANKING_TIME[3:0]
IDISS_TIME[3:0]
LRA
only
ZC_DET_TIME[1:0]
Figure 24. Calibration-Engine Functional Diagram
Variation occurs between different actuators even if the actuators are of the same model. To ensure optimal
results, TI recommends that the calibration routine be run at least once for each actuator. The OTP feature of the
DRV2604L device can store the calibration values. Because of the stored values, the calibration procedure does
not have run every time. Having a single set of calibration register values that can be loaded during the system
initialization is possible.
26
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
Programming (continued)
The following instructions list the step-by-step register configuration for auto-calibration. For additional details see
the Register Map section.
1. Apply the supply voltage to the DRV2604L device, and pull the EN pin high. The supply voltage should allow for
adequate drive voltage of the selected actuator.
2. Write a value of 0x07 to register 0x01. This value moves the DRV2604L device out of STANDBY and places the
MODE[2:0] bits in auto-calibration mode.
3. Populate the input parameters required by the auto-calibration engine:
a. ERM_LRA — selection will depend on desired actuator.
b. FB_BRAKE_FACTOR[2:0] — A value of 2 is valid for most actuators.
c. LOOP_GAIN[1:0] — A value of 2 is valid for most actuators.
d. RATED_VOLTAGE[7:0] — See the Rated Voltage Programming section for calculating the correct register value.
e. OD_CLAMP[7:0] — See the Overdrive Voltage-Clamp Programming section for calculating the correct register value.
f. AUTO_CAL_TIME[1:0] — A value of 3 is valid for most actuators.
g. DRIVE_TIME[3:0] — See the Drive-Time Programming for calculating the correct register value.
h. SAMPLE_TIME[1:0] — A value of 3 is valid for most actuators.
i. BLANKING_TIME[3:0] — A value of 1 is valid for most actuators.
j. IDISS_TIME[3:0] — A value of 1 is valid for most actuators.
k. ZC_DET_TIME[1:0] — A value of 0 is valid for most actuators.
4. Set the GO bit (write 0x01 to register 0x0C) to start the auto-calibration process. When auto calibration is complete, the
GO bit automatically clears. The auto-calibration results are written in the respective registers as shown in Figure 24.
5. Check the status of the DIAG_RESULT bit (in register 0x00) to ensure that the auto-calibration routine is complete
without faults.
6. Evaluate system performance with the auto-calibrated settings. Note that the evaluation should occur during the final
assembly of the device because the auto-calibration process can affect actuator performance and behavior. If any
adjustment is required, the inputs can be modified and this sequence can be repeated. If the performance is satisfactory,
the user can do any of the following:
a. Repeat the calibration process upon subsequent power ups.
b. Store the auto-calibration results in host processor memory and rewrite them to the DRV2604L device upon
subsequent power ups. The device retains these settings when in STANDBY mode or when the EN pin is low.
c. Program the results permanently in nonvolatile, on-chip OTP memory. Even when a device power cycle occurs, the
device retains the auto-calibration settings. See the Programming On-Chip OTP Memory section for additional
information.
8.5.7 Programming On-Chip OTP Memory
The OTP memory can only be written once. To permanently program the OTP memory in registers 0x16 through
0x1A, use the following steps:
1. Write registers 0x16 through 0x1A with the desired configuration and calibration values which provide satisfactory
performance.
2. Ensure that the supply voltage (VDD) is between 4 V and 4.4 V. This voltage is required for the nonvolatile memory to
program properly.
3. Set the OTP_PROGRAM bit by writing a value of 0x01 to register 0x1E. When the OTP memory is written which can only
occur once in the device, the OTP_STATUS bit (in register 0x1E) only reads 1.
4. Reset the device by power cycling the device or setting the DEV_RESET bit in register 0x01, and then read registers
0x16 to 0x1A to ensure that the programmed values were retained.
Copyright © 2014–2018, Texas Instruments Incorporated
27
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
Programming (continued)
8.5.8 Waveform Playback Programming
8.5.8.1 Data Formats for Waveform Playback
The DRV2604L smart-loop architecture has three modes of operation. Each of the modes can drive either ERM
or LRA devices.
1. Open-loop mode
2. Closed-loop mode (unidirectional)
3. Closed-loop mode (bidirectional)
Each mode has different advantages and disadvantages. The DRV2604L device brings new cutting-edge
actuator control with closed-loop operation around the back-EMF for automatic overdrive and braking. However,
some existing haptic implementations already include overdrive and braking that are embedded in the waveform
data. Open-loop mode is used to preserve compatibility with such systems.
The following sections show how the input data for each DRV2604L interface is translated to the output drive
signal.
8.5.8.1.1 Open-Loop Mode
In open-loop mode, the reference level for full-scale drive is set by the OD_CLAMP[7:0] bit in Register 0x17. A
mid-scale input value gives no drive signal, and a less-than mid-scale gives a negative drive value. For an ERM,
a negative drive value results in counter-rotation, or braking. For an LRA, a negative drive value results in a 180-
degree phase shift in commutation.
The RTP mode has 8 bits of resolution over the I2C bus. The RTP data can either be in a signed (2s
complement) or unsigned format as defined by the DATA_FORMAT_RTP bit.
Steady-State
Output Magnitude
Open Loop
ERM_OPEN_LOOP = 1 OR LRA_OPEN_LOOP = 1
OD_CLAMP[7:0]
0 V
-OD_CLAMP[7:0]
Input
Input Interface
0%
50%
0x00
0x7F
100%
0x7F
0xFF
PWM
RTP (8-bit) DATA_FORMAT_RTP = 0
0x81
0x00
RTP (8-bit) DATA_FORMAT_RTP = 1
Figure 25.
28
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
Programming (continued)
8.5.8.1.2 Closed-Loop Mode, Unidirectional
In closed-loop unidirectional mode, the DRV2604L device provides automatic overdrive and braking for both
ERM and LRA actuators. Closed-loop unidirectional mode is the easiest mode to use and understand. Closed-
loop unidirectional mode uses the full 8-bit resolution of the driver. Closed-loop unidirectional mode offers the
best performance; however, the data format is not physically compatible with the open-loop mode data that can
be used in some existing systems
The reference level for steady-state full-scale drive is set by the RATED_VOLTAGE[7:0] bit (when auto-
calibration is performed). The output voltage can momentarily exceed the rated voltage for automatic overdrive
and braking, but does not exceed the OD_CLAMP[7:0] voltage. Braking occurs automatically based on the input
signal when the back-EMF feedback determines that braking is necessary.
Because the system is unidirectional in closed-loop unidirectional mode, only unsigned data should be used. The
RTP mode has 8 bits of resolution over the I2C bus. Setting the DATA_FORMAT_RTP bit to 0 (signed) is not
recommended for closed-loop unidirectional mode.
Steady-State
Output Magnitude
Closed Loop, BIDIR_INPUT = 0
RATED_VOLTAGE[7:0]
½ RATED_VOLTAGE[7:0]
Full Braking
Input
Input Interface
PWM
0%
50%
100%
0xFF
RTP (8-bit) DATA_FORMAT_RTP = 1
0x00
0x7F
Figure 26.
For the RTP interface, set the DATA_FORMAT_RTP bit to 1 (unsigned).
Copyright © 2014–2018, Texas Instruments Incorporated
29
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
Programming (continued)
8.5.8.1.3 Closed-Loop Mode, Bidirectional
In closed-loop bidirectional mode, the DRV2604L device provides automatic overdrive and braking for both ERM
and LRA devices. Closed-loop bidirectional mode preserves compatibility with data created in open-loop
signaling by maintaining zero drive-strength at the mid-scale value. When input values less than the mid-scale
value are given, the DRV2604L device interprets them as the same as the mid-scale with zero drive.
The reference level for steady-state full-scale drive is set by the RATED_VOLTAGE[7:0] bit (when auto
calibration is performed). The output voltage can momentarily exceed the rated voltage for automatic overdrive
and braking, but does not exceed the OD_CLAMP[7:0] voltage. Braking occurs automatically based on the input
signal when the back-EMF feedback determines that braking is necessary. Although the Closed-Loop mode
preserves compatibility with existing device data formats, it provides closed loop benefits and is the default
configuration at power up.
The RTP mode has 8 bits of resolution over the I2C bus. The RTP data can either be in signed (2s complement)
or unsigned format as defined by the DATA_FORMAT_RTP bit.
Steady-State
Output Magnitude
Closed Loop, BIDIR_INPUT = 1
RATED_VOLTAGE[7:0]
½ RATED_VOLTAGE[7:0]
Full Braking
Input
Input Interface
0%
50%
0x00
0x7F
75%
0x3F
0xBF
100%
0x7F
0xFF
PWM
RTP (8-bit) DATA_FORMAT_RTP = 0
0x81
0x00
RTP (8-bit) DATA_FORMAT_RTP = 1
Figure 27.
30
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
Programming (continued)
8.5.8.2 Waveform Setup and Playback
Playback of a haptic effect can occur in multiple ways. Using the PWM mode, RTP mode, and analog-input
mode can provide the waveform in real time. The waveforms can also be played from the RAM in which case the
waveform playback engine is used and the waveform is either played by an internal GO bit (register 0x0C), or by
an external trigger.
8.5.8.2.1 Waveform Playback Using RTP Mode
The user can enter the RTP mode by writing the MODE[2:0] bit to 5 in register 0x01. When in RTP mode, the
DRV2604L device drives the actuator continuously with the amplitude specified in the RTP_INPUT[7:0] bit (in
register 0x02). Because the amplitude tracks the value specified in the RTP_INPUT[7:0] bit, the I2C bus can
stream waveforms.
8.5.8.2.2 Waveform Playback Using the Analog-Input Mode
The user can enter the analog-input mode by setting the MODE[2:0] bit to 3 in register 0x01 and by setting the
N_PWM_ANALOG bit to 1 in register 0x1D. When in analog-input mode, the DRV2604L device accepts an
analog voltage at the IN/TRIG pin. The DRV2604L device drives the actuator continuously in analog-input mode
until the user sets the device into STANDBY mode or enters another interface mode. The reference voltage in
analog-input mode is 1.8 V. Therefore a 1.8-V reference voltage is interpreted as a 100% input value, a 0.9-V
reference voltage is interpreted as 50%, and a 0-V reference voltage is interpreted as 0%. The input value is
analogous to the duty-cycle percentage in PWM mode. The interpretation of these percentages varies according
to the selected mode of operation. See the Data Formats for Waveform Playback section for details.
8.5.8.2.3 Waveform Playback Using PWM Mode
The user can enter the PWM mode by setting the MODE[2:0] bit to 3 in register 0x01 and by setting the
N_PWM_ANALOG bit to 0 in register 0x1D. When in PWM mode, the DRV2604L device accepts PWM data at
the IN/TRIG pin. The DRV2604L device drives the actuator continuously in PWM mode until the user sets the
device to STANDBY mode or to enter another interface mode. The interpretation of the duty-cycle information
varies according to the selected mode of operation. See the Data Formats for Waveform Playback section for
details.
8.5.8.2.4 Loading Data to RAM
The DRV2604LL device contains 2 kB of integrated RAM to store customer waveforms. The waveforms are
represented as time-amplitude pairs. Using the playback engine, the waveforms can be recalled, sequenced, and
played through the I2C or an external GPIO trigger.
A library consists of a revision byte (should be set to 0), a header section, and the waveform data content. The
library header defines the data boundaries for each effect ID in the data field, and the waveform data contains a
sequence of time-value pairs that define the effects.
RAM
0x000
Revision
Header
Waveform Data
0x7FF
Figure 28. RAM Memory Structure
Copyright © 2014–2018, Texas Instruments Incorporated
31
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
Programming (continued)
8.5.8.2.4.1 Header Format
The header block consist of N-boundary definition blocks of 3 bytes each. N is the number of effects stored in the
RAM. Each of the boundary definition blocks contain the start address (2 bytes) and a configuration byte.
The start address contains the location in the memory where the waveform data associated with this effect
begins. The position of the effect pointer in the header becomes the effect ID. The first effect boundary definition
points to the ID for effect 1, the second definition points to the ID for effect 2, and so on. This resulting effect ID
is the effect ID that is used in the waveform sequencer.
Memory location
Header
Effect ID
0x000
Revision
Start address
upper byte
Start address
lower byte
0x001
0x004
0x007
Configuration byte
Configuration byte
Configuration byte
Effect 1
Effect 2
Effect 3
Start address
upper byte
Start address
lower byte
Start address
upper byte
Start address
lower byte
Start address
upper byte
Start address
lower byte
(N œ 1) × 3 + 1
Configuration byte
Effect N
Figure 29. Header Structure
The configuration byte contains the following two parameters:
•
•
The effect size contains the amount of bytes that define the waveform data. An effect size of 0 is an error
state. Any odd-number effect size is an error state because the waveform data is defined as time-value (2
bytes). Therefore, the effect size must be an even number between 2 and 30.
The WAVEFORM_REPEATS[2:0] bit is used to select the number of times the complete waveform is be
played when it is called by the waveform sequencer. A value of 0 is no repeat and the waveform is played
once. A value of 1 means 1 repeat and the waveform is played twice. A value of 7 means infinite repeat until
the GO bit is cleared.
During waveform design, ensure that the appropriate amount of drive time is at zero amplitude on the end of the
waveform so that the waveform stored in the RAM is repeated smoothly.
Configuration byte
Waveform repeats [2:0]
Effect size [4:0]
Figure 30. Header Configuration Byte Structure
8.5.8.2.4.2 RAM Waveform Data Format
The library data contents can take two forms which are voltage-time pair and linear ramp. The voltage-time pair
method implements a set and wait protocol, which is an efficient method of actuator control for most types of
waveforms. This method becomes inefficient when ramping waveforms is desired, therefore a linear ramp
method is also supported which linearly interpolates a set of voltages between two amplitude values. Both
methods require only two bytes of data per set point. The linear ramp method uses a minimum of four bytes so
that linear interpolation can be done to the next set point. The most significant bit of the voltage value is reserved
to indicate the linear ramping mode.
32
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
Programming (continued)
Waveform data
Voltage [6:0]
Time [7:0]
Voltage [6:0]
Time [7:0]
Ramp
Ramp
Ramp
Voltage [6:0]
Time [7:0]
Figure 31. Waveform Data Structure
Data is stored as interleaved voltage-time pairs. Voltage in the voltage-time pair is a 7-bit signed number with
range –63 to 63 when in bidirectional mode (BIDIR_INPUT = 1), and a 7-bit unsigned number with a range of 0
to 127 when in unidirectional mode (BIDIR_INPUT = 0). The MSB of the voltage byte is reserved for the linear
ramping mode.
The Time value is the number of ticks that the Voltage will last. The size of the tick depends on the
PLAYBACK_INTERVAL bit (in register 0x1F). If PLAYBACK_INTERVAL = 0 the absolute time is number of ticks
× 5 ms. If PLAYBACK_INTERVAL = 1 the absolute time is number ticks × 1 ms.
When the most significant bit of the Voltage is high, the engine interprets a linear interpolation between that
voltage and the following voltage point. The following voltage point can either be a part of a regular voltage-time
pair, or a subsequent ramp. The following lists the sequence of bytes:
1. Byte1 — Voltage1 (MSB High)
2. Byte2 — Time1
3. Byte3 — Voltage2
4. Byte4 — Time2
The engine creates a linear interpolation between Voltage1 and Voltage2 over the time period Time1, where
Time1 is a number of 5-ms ticks. The start value for the ramp is the 7-bit value contained in Voltage1. The end
amplitude is the 7-bit value contained in Voltage2. The MSB in Voltage2 can indicate a following voltage-time
pair or the starting point in a subsequent ramp.
8.5.8.2.5 Waveform Sequencer
If the user uses pre-stored effects, the effects must first be loaded into the waveform sequencer, and then the
effects can be launched by using any of the trigger options (see the Waveform Triggers section for details).
The waveform sequencer (see the Waveform Sequencer (Address: 0x04 to 0x0B) section) queues waveform-
library identifiers for playback. Eight sequence registers queue up to eight library waveforms for sequential
playback. A waveform identifier is an integer value referring to the index position of a waveform in the RAM
library. Playback begins at register address 0x04 when the user asserts the GO bit (register 0x0C). When
playback of that waveform ends, the waveform sequencer plays the next waveform identifier held in register
0x05, if the next waveform is non-zero. The waveform sequencer continues in this way until the sequencer
reaches an identifier value of zero or until all eight identifiers are played (register addresses 0x04 through 0x0B),
whichever comes first.
The waveform identifier range is 1 to 127. The MSB of each sequence register can be used to implement a delay
between sequence waveforms. When the MSB is high, bits 6-0 indicate the length of the wait time. The wait time
for that step then becomes WAV_FRM_SEQ[6:0] × 10 ms.
Copyright © 2014–2018, Texas Instruments Incorporated
33
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
Programming (continued)
GO
Waveform Sequencer
WAV_FRM_SEQ0[7:0]
WAV_FRM_SEQ1[7:0]
WAV_FRM_SEQ2[7:0]
WAV_FRM_SEQ3[7:0]
WAV_FRM_SEQ4[7:0]
WAV_FRM_SEQ5[7:0]
WAV_FRM_SEQ6[7:0]
WAV_FRM_SEQ7[7:0]
RAM
Effect 1
Effect 2
Effect 3
Effect 4
Effect 5
Effect N
Figure 32. Waveform Sequencer Programming
8.5.8.2.6 Waveform Triggers
When the waveform sequencer has the effect (or effects) loaded, the waveform sequencer can be triggered by
an internal trigger, external trigger (edge), or external trigger (level). To trigger using the internal trigger set the
MODE[2:0] bit to 0 in register 0x01. To trigger using the external trigger (edge), set the MODE[2:0] bit to 1 and
then follow the trigger instructions listed in the Edge Trigger section. To trigger using the external trigger (level),
set the MODE[2:0] bit to 2 and then follow the trigger instructions listed in the Level Trigger section.
34
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
8.6 Register Map
Table 2. Register Map Overview
REG
DEFAULT
NO.
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
0x1F
0x20
0x21
0x22
0xFD
0xFE
0xFF
0xC0
0x40
0x00
0x00
0x01
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x3E
0x9B
0x0C
0x6F
0x36
0x93
0xF5
0x80
0x20
0x80
0x33
0x00
0x00
0x00
0x00
0x00
DEVICE_ID[2:0]
STANDBY
ILLEGAL_ADDR
Reserved
DIAG_RESULT
Reserved
OVER_TEMP
MODE[2:0]
OC_DETECT
DEV_RESET
RTP_INPUT[7:0]
Reserved
HI_Z
Reserved
WAIT1
WAIT2
WAIT3
WAIT4
WAIT5
WAIT6
WAIT7
WAIT8
WAV_FRM_SEQ1[6:0]
WAV_FRM_SEQ2[6:0]
WAV_FRM_SEQ3[6:0]
WAV_FRM_SEQ4[6:0]
WAV_FRM_SEQ5[6:0]
WAV_FRM_SEQ6[6:0]
WAV_FRM_SEQ7[6:0]
WAV_FRM_SEQ8[6:0]
Reserved
GO
ODT[7:0]
SPT[7:0]
SNT[7:0]
BRT[7:0]
RATED_VOLTAGE[7:0]
OD_CLAMP[7:0]
A_CAL_COMP[7:0]
A_CAL_BEMF[7:0]
N_ERM_LRA
STARTUP_BOOST
BIDIR_INPUT
FB_BRAKE_FACTOR[2:0]
AC_COUPLE
LOOP_GAIN[1:0]
DRIVE_TIME[4:0]
BLANKING_TIME[1:0]
BEMF_GAIN[1:0]
Reserved
BRAKE_STABILIZER
SAMPLE_TIME[1:0]
IDISS_TIME[1:0]
NG_THRESH[1:0]
ERM_OPEN_LOOP
SUPPLY_COMP_DIS
DATA_FORMAT_RTP
Reserved
LRA_DRIVE_MODE
OTP_STATUS
N_PWM_ANALOG
Reserved
LRA_OPEN_LOOP
OTP_PROGRAM
ZC_DET_TIME[1:0]
AUTO_OL_CNT[1:0]
AUTO_CAL_TIME[1:0]
LRA_AUTO_OPEN_LOOP
PLAYBACK_INTERVAL
BLANKING_TIME[3:2]
OL_LRA_PERIOD[6:0]
VBAT[7:0]
IDISS_TIME[3:2]
Reserved
LRA_PERIOD[7:0]
RAM_ADDR_UB[7:0]
RAM_ADDR_LB[7:0]
RAM_DATA[7:0]
Copyright © 2014–2018, Texas Instruments Incorporated
35
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
8.6.1 Status (Address: 0x00)
Figure 33. Status Register
7
6
5
4
3
2
1
0
DEVICE_ID[2:0]
RO-1
ILLEGAL_ADDR
RO-0
DIAG_RESULT
RO-0
Reserved
OVER_TEMP
RO-0
OC_DETECT
RO-0
RO-1
RO-0
Table 3. Status Register Field Descriptions
BIT FIELD
TYPE
DEFAULT
DESCRIPTION
7-5 DEVICE_ID[2:0]
RO
6
Device identifier. The DEVICE_ID bit indicates the part number to the user.
The user software can ascertain the device capabilities by reading this
register.
3: DRV2605 (contains licensed ROM library, does not contain RAM)
4: DRV2604 (contains RAM, does not contain licensed ROM library)
6: DRV2604L (low-voltage version of the DRV2604 device)
7: DRV2605L (low-voltage version of the DRV2605 device)
4
3
ILLEGAL_ADDR
DIAG_RESULT
RO
RO
0
0
This flag will indicate if a user programming error to the RAM has occurred.
The bit is set when the user tries to read or write memory outside of the
RAM address range, or if the user instructs the device to play an odd
number of bytes
This flag stores the result of the auto-calibration routine and the diagnostic
routine. The flag contains the result for whichever routine was executed
last. The flag clears upon read. Test result is not valid until the GO bit self-
clears at the end of the routine.
Auto-calibration mode:
0: Auto-calibration passed (optimum result converged)
1: Auto-calibration failed (result did not converge)
Diagnostic mode:
0: Actuator is functioning normally
1: Actuator is not present or is shorted, timing out, or giving
out–of-range back-EMF
2
1
Reserved
OVER_TEMP
RO
RO
0
0
Latching overtemperature detection flag. If the device becomes too hot, it
shuts down. This bit clears upon read.
0: Device is functioning normally
1: Device has exceeded the temperature threshold
0
OC_DETECT
Latching overcurrent detection flag. If the load impedance is below the
load-impedance threshold, the device shuts down and periodically attempts
to restart until the impedance is above the threshold.
0: No overcurrent event is detected
1: Overcurrent event is detected
36
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
8.6.2 Mode (Address: 0x01)
Figure 34. Mode Register
7
6
5
4
3
2
1
0
DEV_RESET
R/W-0
STANDBY
R/W-1
Reserved
MODE[2:0]
R/W-0
Table 4. Mode Register Field Descriptions
BIT FIELD
TYPE
DEFAULT
DESCRIPTION
7
DEV_RESET
R/W
0
Device reset. Setting this bit performs the equivalent operation of power
cycling the device. Any playback operations are immediately interrupted,
and all registers are reset to the default values. The DEV_RESET bit self-
clears after the reset operation is complete.
6
STANDBY
R/W
R/W
1
0
Software standby mode
0: Device ready
1: Device in software standby
5-3 Reserved
2-0 MODE
0: Internal trigger
Waveforms are fired by setting the GO bit in register 0x0C.
1: External trigger (edge mode)
A rising edge on the IN/TRIG pin sets the GO Bit. A second rising
edge on the IN/TRIG pin cancels the waveform if the second rising
edge occurs before the GO bit has cleared.
2: External trigger (level mode)
The GO bit follows the state of the external trigger. A rising edge on
the IN/TRIG pin sets the GO bit, and a falling edge sends a cancel. If
the GO bit is already in the appropriate state, no change occurs.
3: PWM input and analog input
A PWM or analog signal is accepted at the IN/TRIG pin and used as
the driving source. The device actively drives the actuator while in
this mode. The PWM or analog input selection occurs by using the
N_PWM_ANALOG bit.
4: Reserved.
5: Real-time playback (RTP mode)
The device actively drives the actuator with the contents of the
RTP_INPUT[7:0] bit in register 0x02.
6: Diagnostics
Set the device in this mode to perform a diagnostic test on the
actuator. The user must set the GO bit to start the test. The test is
complete when the GO bit self-clears. Results are stored in the
DIAG_RESULT bit in register 0x00.
7: Auto calibration
Set the device in this mode to auto calibrate the device for the
actuator. Before starting the calibration, the user must set the all
required input parameters. The user must set the GO bit to start the
calibration. Calibration is complete when the GO bit self-clears. For
more information see the Auto Calibration Procedure section.
Copyright © 2014–2018, Texas Instruments Incorporated
37
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
8.6.3 Real-Time Playback Input (Address: 0x02)
Figure 35. Real-Time Playback Input Register
7
6
5
4
3
2
1
0
RTP_INPUT[7:0]
R/W-0
Table 5. Real-Time Playback Input Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT DESCRIPTION
7-0
RTP_INPUT[7:0]
R/W
0
This field is the entry point for real-time playback (RTP) data. The
DRV2604L playback engine drives the RTP_INPUT[7:0] value to the load
when MODE[2:0] = 5 (RTP mode). The RTP_INPUT[7:0] value can be
updated in real-time by the host controller to create haptic waveforms. The
RTP_INPUT[7:0] value is interpreted as signed by default, but can be set to
unsigned by the DATA_FORMAT_RTP bit in register 0x1D. When the
haptic waveform is complete, the user can idle the device by setting
MODE[2:0] = 0, or alternatively by setting STANDBY = 1.
8.6.4 HI_Z (Address: 0x03)
Figure 36. HI_Z Register
7
6
5
4
3
2
1
0
Reserved
HI_Z
R/W-0
Reserved
Table 6. HI_Z Register Field Descriptions
BIT FIELD
TYPE
DEFAULT
DESCRIPTION
7-5 Reserved
4
HI_Z
R/W
0
This bit sets the output driver into a true high-impedance state. The device
must be enabled to go into the high-impedance state. When in hardware
shutdown or standby mode, the output drivers have 15 kO to ground. When
the HI_Z bit is asserted, the hi-Z functionality takes effect immediately, even
if a transaction is taking place.
3-0 Reserved
38
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
8.6.5 Waveform Sequencer (Address: 0x04 to 0x0B)
Figure 37. Waveform Sequencer Register
7
6
5
4
3
2
1
0
WAIT
R/W-0
WAV_FRM_SEQ[6:0]
R/W-0
Table 7. Waveform Sequencer Register Field Descriptions
BIT FIELD
TYPE
DEFAULT
DESCRIPTION
7
WAIT
R/W
0
When this bit is set, the WAV_FRM_SEQ[6:0] bit is interpreted as a wait
time in which the playback engine idles. This bit is used to insert timed
delays between sequentially played waveforms.
Delay time = 10 ms × WAV_FRM_SEQ[6:0]
If WAIT = 0, then WAV_FRM_SEQ[6:0] is interpreted as a waveform
identifier for sequence playback.
6-0 WAV_FRM_SEQ
R/W
0
Waveform sequence value. This bit holds the waveform identifier of the
waveform to be played. A waveform identifier is an integer value referring
to the index position of a waveform in the RAM library. Playback begins at
register address 0x04 when the user asserts the GO bit (register 0x0C).
When playback of that waveform ends, the waveform sequencer plays the
next waveform identifier held in register 0x05, if the next waveform
identifier is non-zero. The waveform sequencer continues in this way until
the sequencer reaches an identifier value of zero, or all eight identifiers are
played (register addresses 0x04 through 0x0B), whichever comes first.
8.6.6 GO (Address: 0x0C)
Figure 38. GO Register
7
6
5
4
3
2
1
0
Reserved
GO
R/W-0
Table 8. GO Register Field Descriptions
BIT
7-1
0
FIELD
Reserved
GO
TYPE
DEFAULT
DESCRIPTION
R/W
0
This bit is used to fire processes in the DRV2604L device. The process
fired by the GO bit is selected by the MODE[2:0] bit (register 0x01). The
primary function of this bit is to fire playback of the waveform identifiers in
the waveform sequencer (registers 0x04 to 0x0B), in which case, this bit
can be thought of a software trigger for haptic waveforms. The GO bit
remains high until the playback of the haptic waveform sequence is
complete. Clearing the GO bit during waveform playback cancels the
waveform sequence. Using one of the external trigger modes can cause
the GO bit to be set or cleared by the external trigger pin. This bit can also
be used to fire the auto-calibration process or the diagnostic process.
Copyright © 2014–2018, Texas Instruments Incorporated
39
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
8.6.7 Overdrive Time Offset (Address: 0x0D)
Figure 39. Overdrive Time Offset Register
7
6
5
4
3
2
1
0
ODT[7:0]
R/W-0
Table 9. Overdrive Time Offset Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT DESCRIPTION
7-0
ODT
R/W
0
This bit adds
a time offset to the overdrive portion of the library
waveforms. Some motors require more overdrive time than others,
therefore this register allows the user to add or remove overdrive time
from the library waveforms. The maximum voltage value in the library
waveform is automatically determined to be the overdrive portion. This
register is only useful in open-loop mode. Overdrive is automatic for
closed-loop mode. The offset is interpreted as 2s complement, therefore
the time offset can be positive or negative.
Overdrive Time Offset (ms) = ODT[7:0] × PLAYBACK_INTERVAL
8.6.8 Sustain Time Offset, Positive (Address: 0x0E)
Figure 40. Sustain Time Offset, Positive Register
7
6
5
4
3
2
1
0
SPT[7:0]
R/W-0
Table 10. Sustain Time Offset, Positive Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT DESCRIPTION
7-0
SPT
R/W
0
This bit adds a time offset to the positive sustain portion of the library
waveforms. Some motors have a faster or slower response time than
others, therefore this register allows the user to add or remove positive
sustain time from the library waveforms. Any positive voltage value other
than the overdrive portion is considered as a sustain positive value. The
offset is interpreted as 2s complement, therefore the time offset can positive
or negative.
Sustain-Time Positive Offset (ms) = SPT[7:0] ×
PLAYBACK_INTERVAL
40
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
8.6.9 Sustain Time Offset, Negative (Address: 0x0F)
Figure 41. Sustain Time Offset, Negative Register
7
6
5
4
3
2
1
0
SNT[7:0]
R/W-0
Table 11. Sustain Time Offset, Negative Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
SNT
R/W
0
This bit adds a time offset to the negative sustain portion of the library
waveforms. Some motors have a faster or slower response time than
others, therefore this register allows the user to add or remove negative
sustain time from the library waveforms. Any negative voltage value other
than the overdrive portion is considered as a sustaining negative value. The
offset is interpreted as two’s complement, therefore the time offset can be
positive or negative.
Sustain-Time Negative Offset (ms) = SNT[7:0] ×
PLAYBACK_INTERVAL
8.6.10 Brake Time Offset (Address: 0x10)
Figure 42. Brake Time Offset Register
7
6
5
4
3
2
1
0
BRT[7:0]
R/W-0
Table 12. Brake Time Offset Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT DESCRIPTION
7-0
BRT
R/W
0
This bit adds a time offset to the braking portion of the library waveforms.
Some motors require more braking time than others, therefore this register
allows the user to add or take away brake time from the library waveforms.
The most negative voltage value in the library waveform is automatically
determined to be the braking portion. This register is only useful in open-loop
mode. Braking is automatic for closed-loop mode. The offset is interpreted as
2s complement, therefore the time offset can be positive or negative.
Brake Time Offset (ms) = BRT[7:0] × PLAYBACK_INTERVAL
Copyright © 2014–2018, Texas Instruments Incorporated
41
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
8.6.11 Rated Voltage (Address: 0x16)
Figure 43. Rated Voltage Register
7
6
5
4
3
2
1
0
RATED_VOLTAGE[7:0]
R/W-0
R/W-0
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-0
Table 13. Rated Voltage Register Field Descriptions
BIT FIELD
TYPE
DEFAULT
DESCRIPTION
7-0 RATED_VOLTAGE[7:0]
R/W
0x3E
This bit sets the reference voltage for full-scale output during closed-loop
operation. The auto-calibration routine uses this register as an input, therefore
this register must be written with the rated voltage value of the motor before
calibration is performed. This register is ignored for open-loop operation
because the overdrive voltage sets the reference for that case. Any
modification of this register value should be followed by calibration to set
A_CAL_BEMF appropriately.
See the Rated Voltage Programming section for calculating the correct register
value.
8.6.12 Overdrive Clamp Voltage (Address: 0x17)
Figure 44. Overdrive Clamp Voltage Register
7
6
5
4
3
2
1
0
OD_CLAMP[7:0]
R/W-1
R/W-0
R/W-0
R/W-1
R/W-1
R/W-0
R/W-1
R/W-1
Table 14. Overdrive Clamp Voltage Register Field Descriptions
BIT
FIELD
OD_CLAMP[7:0]
TYPE
DEFAULT
DESCRIPTION
7
R/W
0x9B
During closed-loop operation the actuator feedback allows the output voltage
to go above the rated voltage during the automatic overdrive and automatic
braking periods. This register sets a clamp so that the automatic overdrive is
bounded. This bit also serves as the full-scale reference voltage for open-loop
operation.
See the Overdrive Voltage-Clamp Programming section for calculating the
correct register value.
8.6.13 Auto-Calibration Compensation Result (Address: 0x18)
Figure 45. Auto-Calibration Compensation-Result Register
7
6
5
4
3
2
1
0
A_CAL_COMP[7:0]
R/W-0
R/W-0
R/W-0
R/W-0
R/W-1
R/W-1
R/W-0
R/W-0
Table 15. Auto-Calibration Compensation-Result Register Field Descriptions
BIT
FIELD
A_CAL_COMP[7:0]
TYPE
DEFAULT
DESCRIPTION
7-0
R/W
0x0C
This register contains the voltage-compensation result after execution of auto
calibration. The value stored in the A_CAL_COMP bit compensates for any
resistive losses in the driver. The calibration routine checks the impedance of
the actuator to automatically determine an appropriate value. The auto-
calibration compensation-result value is multiplied by the drive gain during
playback.
Auto-calibration compensation coefficient = 1 + A_CAL_COMP[7:0] / 255
42
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
8.6.14 Auto-Calibration Back-EMF Result (Address: 0x19)
Figure 46. Auto-Calibration Back-EMF Result Register
7
6
5
4
3
2
1
0
A_CAL_BEMF[7:0]
R/W-0
R/W-1
R/W-1
R/W-0
R/W-1
R/W-1
R/W-0
R/W-0
Table 16. Auto-Calibration Back-EMF Result Register Field Descriptions
BIT FIELD
TYPE
DEFAULT
DESCRIPTION
7-0 A_CAL_BEMF[7:0]
R/W
0x6C
This register contains the rated back-EMF result after execution of auto
calibration. The A_CAL_BEMF[7:0] bit is the level of back-EMF voltage that the
actuator gives when the actuator is driven at the rated voltage. The DRV2604L
playback engine uses this the value stored in this bit to automatically determine
the appropriate feedback gain for closed-loop operation.
Auto-calibration back-EMF (V) = (A_CAL_BEMF[7:0] / 255) × 1.22 V /
BEMF_GAIN[1:0]
Copyright © 2014–2018, Texas Instruments Incorporated
43
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
8.6.15 Feedback Control (Address: 0x1A)
Figure 47. Feedback Control Register
7
6
5
4
3
2
1
0
N_ERM_LRA
R/W-0
FB_BRAKE_FACTOR[2:0]
R/W-1
LOOP_GAIN[1:0]
BEMF_GAIN[1:0]
R/W-0
R/W-0
R/W-1
R/W-0
R/W-1
R/W-1
Table 17. Feedback Control Register Field Descriptions
BIT FIELD
TYPE
DEFAULT
DESCRIPTION
7
N_ERM_LRA
R/W
0
This bit sets the DRV2604L device in ERM or LRA mode. This bit should be set
prior to running auto calibration.
0: ERM Mode
1: LRA Mode
6-4 FB_BRAKE_FACTOR[2:0]
R/W
3
This bit selects the feedback gain ratio between braking gain and driving gain.
In general, adding additional feedback gain while braking is desirable so that the
actuator brakes as quickly as possible. Large ratios provide less-stable
operation than lower ones. The advanced user can select to optimize this
register. Otherwise, the default value should provide good performance for most
actuators. This value should be set prior to running auto calibration.
0: 1x
1: 2x
2: 3x
3: 4x
4: 6x
5: 8x
6: 16x
7: Braking disabled
3-2 LOOP_GAIN[1:0]
R/W
1
This bit selects a loop gain for the feedback control. The LOOP_GAIN[1:0] bit
sets how fast the loop attempts to make the back-EMF (and thus motor velocity)
match the input signal level. Higher loop-gain (faster settling) options provide
less-stable operation than lower loop gain (slower settling). The advanced user
can select to optimize this register. Otherwise, the default value should provide
good performance for most actuators. This value should be set prior to running
auto calibration.
0: Low
1: Medium (default)
2: High
3: Very High
1-0 BEMF_GAIN[1:0]
R/W
2
This bit sets the analog gain of the back-EMF amplifier. This value is interpreted
differently between ERM mode and LRA mode. Auto calibration automatically
populates the BEMF_GAIN bit with the most appropriate value for the actuator.
ERM Mode
0: 0.255x
1: 0.7875x
2: 1.365x (default)
3: 3.0x
LRA Mode
0: 3.75x
1: 7.5x
2: 15x (default)
3: 22.5x
44
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
8.6.16 Control1 (Address: 0x1B)
Figure 48. Control1 Register
7
6
5
4
3
2
1
0
STARTUP_BOOST
R/W-1
Reserved
AC_COUPLE
R/W-0
DRIVE_TIME[4:0]
R/W-0
R/W-1
R/W-0
R/W-1
R/W-1
Table 18. Control1 Register Field Descriptions
BIT FIELD
TYPE
DEFAULT DESCRIPTION
7
STARTUP_BOOST
R/W
1
This bit applies higher loop gain during overdrive to enhance actuator transient
response.
6
5
Reserved
AC_COUPLE
R/W
0
This bit applies a 0.9-V common mode voltage to the IN/TRIG pin when an AC-
coupling capacitor is used. This bit is only useful for analog input mode. This bit
should not be asserted for PWM mode or external trigger mode.
0: Common-mode drive disabled for DC-coupling or digital inputs modes
1: Common-mode drive enabled for AC coupling
4-0 DRIVE_TIME[4:0]
R/W
0x13
LRA Mode: Sets initial guess for LRA drive-time in LRA mode. Drive time is
automatically adjusted for optimum drive in real time; however, this register
should be optimized for the approximate LRA frequency. If the bit is set too low,
it can affect the actuator startup time. If the bit is set too high, it can cause
instability.
Optimum drive time (ms) ≈ 0.5 × LRA Period
Drive time (ms) = DRIVE_TIME[4:0] × 0.1 ms + 0.5 ms
ERM Mode: Sets the sample rate for the back-EMF detection. Lower drive times
cause higher peak-to-average ratios in the output signal, requiring more supply
headroom. Higher drive times cause the feedback to react at a slower rate.
Drive Time (ms) = DRIVE_TIME[4:0] × 0.2 ms + 1 ms
Copyright © 2014–2018, Texas Instruments Incorporated
45
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
8.6.17 Control2 (Address: 0x1C)
Figure 49. Control2 Register
7
6
5
4
3
2
1
0
BIDIR_INPUT
BRAKE_STABILIZE
R
SAMPLE_TIME[1:0]
R/W-1
BLANKING_TIME[1:0]
IDISS_TIME[1:0]
R/W-1
R/W-1
R/W-0
R/W-1
R/W-0
R/W-1
Table 19. Control2 Register Field Descriptions
BIT FIELD
TYPE
DEFAULT
DESCRIPTION
7
BIDIR_INPUT
R/W
1
The BIDIR_INPUT bit selects how the engine interprets data.
0: Unidirectional input mode
Braking is automatically determined by the feedback conditions and is
applied when required. Use of this mode also recovers an additional bit
of vertical resolution. This mode should only be used for closed-loop
operation.
Examples::
0% Input ? No output signal
50% Input ? Half-scale output signal
100% Input ? Full-scale output signal
1: Bidirectional input mode (default)
This mode is compatible with traditional open-loop signaling and also
works well with closed-loop mode. When operating closed-loop, braking
is automatically determined by the feedback conditions and applied
when required. When operating open-loop modes, braking is only
applied when the input signal is less than 50%.
Open-loop mode (ERM and LRA) examples:
0% Input ? Negative full-scale output signal (braking)
25% Input ? Negative half-scale output signal (braking)
50% Input ? No output signal
75% Input ? Positive half-scale output signal
100% Input ? Positive full-scale output signal
Closed-loop mode (ERM and LRA) examples:
0% to 50% Input ? No output signal
50% Input ? No output signal
75% Input ? Half-scale output signal
100% Input ? Full-scale output signal
6
BRAKE_STABILIZER
R/W
R/W
1
3
When this bit is set, loop gain is reduced when braking is almost complete to
improve loop stability
5-4 SAMPLE_TIME[1:0]
LRA auto-resonance sampling time (Advanced use only)
0: 150 µs
1: 200 µs
2: 250 µs
3: 300 µs
46
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
Table 19. Control2 Register Field Descriptions (continued)
BIT FIELD
TYPE
DEFAULT
DESCRIPTION
3-2 BLANKING_TIME[1:0]
R/W
1
Blanking time before the back-EMF AD makes a conversion. (Advanced use only)
Blanking time for LRA has an additional 2 bits (BLANKING_TIME[3:2]) located in
register 0x1F. Depending on the status of N_ERM_LRA the blanking time
represents different values.
N_ERM_LRA = 0 (ERM mode)
0: 45 µs
1: 75 µs
2: 150 µs
3: 225 µs
N_ERM_LRA = 1(LRA mode)
0: 15 µs
1: 25 µs
2: 50 µs
3: 75 µs
4: 90 µs
5: 105 µs
6: 120 µs
7: 135 µs
8: 150 µs
9: 165 µs
10: 180 µs
11: 195 µs
12: 210 µs
13: 235 µs
14: 260 µs
15: 285 µs
Copyright © 2014–2018, Texas Instruments Incorporated
47
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
Table 19. Control2 Register Field Descriptions (continued)
BIT FIELD
TYPE
DEFAULT
DESCRIPTION
1-0 IDISS_TIME[1:0]
R/W
1
Current dissipation time. This bit is the time allowed for the current to dissipate
from the actuator between PWM cycles for flyback mitigation. (Advanced use
only)
the current dissipation time for LRA has an additional 2 bits (IDISS_TIME[3:2])
located in register 0x1F. Depending on the status of N_ERM_LRA the idiss time
represents different values
N_ERM_LRA = 0 (ERM mode)
0: 45 µs
1: 75 µs
2: 150 µs
3: 225 µs
N_ERM_LRA = 1(LRA mode)
0: 15 µs
1: 25 µs
2: 50 µs
3: 75 µs
4: 90 µs
5: 105 µs
6: 120 µs
7: 135 µs
8: 150 µs
9: 165 µs
10: 180 µs
11: 195 µs
12: 210 µs
13: 235 µs
14: 260 µs
15: 285 µs
48
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
8.6.18 Control3 (Address: 0x1D)
Figure 50. Control3 Register
7
6
5
4
3
2
1
0
NG_THRESH[1:0]
ERM_OPEN_LOOP
SUPPLY_COMP_DI DATA_FORMAT_RT LRA_DRIVE_MODE
N_PWM_ANALOG
LRA_OPEN_LOOP
S
P
R/W-1
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
Table 20. Control3 Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-6 NG_THRESH[1:0]
R/W
R/W
R/W
2
0
0
This bit is the noise-gate threshold for PWM and analog inputs.
0: Disabled
1: 2%
2: 4% (Default)
3: 8%
5
4
ERM_OPEN_LOOP
This bit selects mode of operation while in ERM mode. Closed-loop operation is
usually desired for because of automatic overdrive and braking properties.
However, many existing waveform libraries were designed for open-loop
operation, therefore open-loop operation can be required for compatibility.
0: Closed Loop
1: Open Loop
SUPPLY_COMP_DIS
This bit disables supply compensation. The DRV2604L device generally
provides constant drive output over variation in the power supply input (VDD). In
some systems, supply compensation can have already been implemented
upstream, therefore disabling the DRV2604L supply compensation can be
useful.
0: Supply compensation enabled
1: Supply compensation disabled
3
2
DATA_FORMAT_RTP
LRA_DRIVE_MODE
R/W
R/W
0
0
This bit selects the input data interpretation for RTP (Real-Time Playback)
mode.
0: Signed
1: Unsigned
This bit selects the drive mode for the LRA algorithm. This bit determines how
often the drive amplitude is updated. Updating once per cycle provides a
symmetrical output signal, while updating twice per cycle provides more precise
control.
0: Once per cycle
1: Twice per cycle
1
0
N_PWM_ANALOG
R/W
R/W
0
0
This bit selects the input mode for the IN/TRIG pin when MODE[2:0] = 3. In
PWM input mode, the duty cycle of the input signal determines the amplitude of
the waveform. In analog input mode, the amplitude of the input determines the
amplitude of the waveform.
0: PWM Input
1: Analog Input
LRA_OPEN_LOOP
This bit selects an open-loop drive option for LRA Mode. When asserted, the
playback engine drives the LRA at the selected frequency independently of the
resonance frequency. In PWM input mode, the playback engine recovers the
LRA commutation frequency from the PWM input, dividing the frequency by
128. Therefore the PWM input frequency must be equal to 128 times the
resonant frequency of the LRA.
In RTP, RAM mode, the frequency is set by the OL_LRA_PERIOD[6:0] bit.
Open-loop mode is not supported if analog input mode is selected.
0: Auto-resonance mode
1: LRA open-loop mode
Copyright © 2014–2018, Texas Instruments Incorporated
49
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
8.6.19 Control4 (Address: 0x1E)
Figure 51. Control4 Register
7
6
5
4
3
2
OTP_STATUS
R-0
1
0
ZC_DET_TIME[1]
R/W-0
ZC_DET_TIME[0]
R/W-0
AUTO_CAL_TIME[1:0]
Reserved
Reserved
OTP_PROGRAM
R/W-0
R/W-1
R/W-0
Table 21. Control4 Register Field Descriptions
BIT
7-6
FIELD
TYPE
DEFAULT
DESCRIPTION
ZC_DET_TIME[1:0]
R/W
0
This bit sets the minimum length of time devoted for detecting a zero crossing
(advanced use only).
0: 100 µs
1: 200 µs
2: 300 µs
3: 390 µs
5-4
AUTO_CAL_TIME[1:0]
R/W
2
This bit sets the length of the auto calibration time. The AUTO_CAL_TIME[1:0]
bit should be enough time for the motor acceleration to settle when driven at the
RATED_VOLTAGE[7:0] value.
0: 150 ms (minimum), 350 ms (maximum)
1: 250 ms (minimum), 450 ms (maximum)
2: 500 ms (minimum), 700 ms (maximum)
3: 1000 ms (minimum), 1200 ms (maximum)
3
2
Reserved
OTP_STATUS
R
0
0
OTP Memory status
0: OTP Memory has not been programmed
1: OTP Memory has been programmed
1
0
Reserved
OTP_PROGRAM
R/W
This bit launches the programming process for one-time programmable (OTP)
memory which programs the contents of register 0x16 through 0x1A into
nonvolatile memory. This process can only be executed one time per device.
See the Programming On-Chip OTP Memory section for details.
50
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
8.6.20 Control5 (Address: 0x1F)
Figure 52. Control5 Register
7
6
5
4
3
2
1
0
AUTO_OL_CNT[1:0]
LRA_AUTO_OPEN_ PLAYBACK_INTER
BLANKING_TIME[3:2]
IDISS_TIME[3:2]
LOOP
VAL
R/W-1
R/W-0
R/W-0
R/W-0
RW-0
RW-0
RW-0
Table 22. Control5 Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-6
AUTO_OL_CNT[1:0]
R/W
2
This bit selects number of cycles required to attempt synchronization before
transitioning to open loop when the LRA_AUTO_OPEN_LOOP bit is asserted,
0: 3 attempts
1: 4 attempts
2: 5 attempts
3: 6 attempts
5
4
LRA_AUTO_OPEN_LOOP
PLAYBACK_INTERVAL
R/W
R/W
0
0
This bit selects the automatic transition to open-loop drive when a back-EMF
signal is not detected (LRA only).
0: Never transitions to open loop
1: Automatically transitions to open loop
This bit selects the memory playback interval.
0: 5 ms
1: 1 ms
3-2
1-0
BLANKING_TIME[3:2]
IDISS_TIME[3:2]
R/W
R/W
0
0
This bit sets the MSB for the BLANKING_TIME[3:0]. See the
BLANKING_TIME[3:0] bit in the Control2 (Address: 0x1C) section for details.
Advanced use only.
This bit sets the MSB for IDISS_TIME[3:0]. See the IDISS_TIME[1:0] bit in the
Control2 (Address: 0x1C) section for details. Advanced use only.
8.6.21 LRA Open Loop Period (Address: 0x20)
Figure 53. LRA Open Loop Period Register
7
6
5
4
3
2
1
0
Reserved
OL_LRA_PERIOD[6:0]
R/W-0
Table 23. LRA Open Loop Period Register Field Descriptions
BIT
FIELD
TYPE
R/W
DEFAULT
DESCRIPTION
7-0 OL_LRA_PERIOD[6:0]
0
This bit sets the period to be used for driving an LRA when open-loop mode is
selected.
LRA open-loop period (µs) = OL_LRA_PERIOD[6:0] × 98.46 µs
8.6.22 V(BAT) Voltage Monitor (Address: 0x21)
Figure 54. V(BAT) Voltage-Monitor Register
7
6
5
4
3
2
1
0
VBAT[7:0]
R/W-0
Copyright © 2014–2018, Texas Instruments Incorporated
51
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
Table 24. V(BAT) Voltage-Monitor Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
VBAT[7:0]
R/W
0
This bit provides a real-time reading of the supply voltage at the VDD pin. The
device must be actively sending a waveform to take a reading.
VDD (V) = VBAT[7:0] × 5.6V / 255
8.6.23 LRA Resonance Period (Address: 0x22)
Figure 55. LRA Resonance-Period Register
7
6
5
4
3
2
1
0
LRA_PERIOD[7:0]
R/W-0
Table 25. LRA Resonance-Period Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
LRA_PERIOD[7:0]
R/W
0
This bit reports the measurement of the LRA resonance period. The device must
be actively sending a waveform to take a reading.
LRA period (us) = LRA_Period[7:0] × 98.46 µs
52
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
8.6.24 RAM-Address Upper Byte (Address: 0xFD)
Figure 56. RAM-Address Upper-Byte Register
7
6
5
4
3
2
1
0
RAM_ADDR_UB[7:0]
R/W-0
Table 26. RAM-Address Upper-Byte Register Field Descriptions
BIT FIELD
TYPE
DEFAULT
DESCRIPTION
7-0 RAM_ADDR_UB[7:0]
R/W
0
The content of this bit is the upper byte for the waveform RAM Address entry.
8.6.25 RAM-Address Lower Byte (Address: 0xFE)
Figure 57. RAM-Address Lower Byte Register
7
6
5
4
3
2
1
0
RAM_ADDR_LB[7:0]
R/W-0
Table 27. RAM Address Lower Byte Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
RAM_ADDR_LB[7:0]
R/W
0
The content of this bit is the lower byte for the waveform RAM address entry.
8.6.26 RAM Data Byte (Address: 0xFF)
Figure 58. RAM-Data Byte Register
7
6
5
4
3
2
1
0
RAM_DATA[7:0]
R/W-0
Table 28. RAM-Data Byte Register Field Descriptions
BIT
FIELD
TYPE
DEFAULT
DESCRIPTION
7-0
RAM_DATA[7:0]
R/W
0
Data entry to waveform RAM interface. The user can perform single-byte writes
or multi-byte writes to this register. The controller starts the write at the address
(RAM_ADDR_UB:RAM_ADDR_LB). For both single-byte and multi-byte writes,
the controller automatically increments the RAM address register for each byte
written to the RAM data register.
Copyright © 2014–2018, Texas Instruments Incorporated
53
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The typical application for a haptic driver is in a touch-enabled system that already has an application processor
which makes the decision on when to execute haptic effects.
The DRV2604L device can be used fully with I2C communications (either using RTP or the memory interface). A
system designer can chose to use external triggers to play low-latency effects (such as from a physical button) or
can decide to use the PWM interface. Figure 59 shows a typical haptic system implementation. The system
designer should not use the internal regulator (REG) to power any external load.
DRV2604L
Application
Processor
OUT+
REG
C
(REG)
LRA or
ERM
SCL
SCL
SDA
EN
M
SDA
GPIO
OUTœ
2 V œ 5.2 V
V
DD
C
(VDD)
PWM/GPIO
IN/TRIG
GND
Copyright © 2016, Texas Instruments Incorporated
Figure 59. I2C Control with Optional PWM Input or External Trigger
Table 29. Recommended External Components
COMPONENT
C(VDD)
DESCRIPTION
SPECIFICATION
Capacitance
Capacitance
Resistance
TYPICAL VALUE
Input capacitor
1 µF
1 µF
C(REG)
Regulator capacitor
Pullup resistor
R(PU)
2.2 kΩ
54
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
9.2 Typical Application
A typical application of the DRV2604L device is in a system that has external buttons which fire different haptic
effects when pressed. Figure 60 shows a typical schematic of such a system. The buttons can be physical
buttons, capacitive-touch buttons, or GPIO signals coming from the touch-screen system.
Effects in this type of system are programmable.
TPS73633
OUT
IN
NR/FB
EN
GND
C
(LDO)
1 µF
R
R
(PU)
2.2 kΩ
(PU)
2.2 kΩ
DRV2604L
MSP430G2553
OUT+
REG
C
(REG)
1 µF
LRA or
M
ERM
AVCC
DVCC
P1.6/SCL
P1.7/SDA
P3.1
SCL
C
(VCC)
0.1 µF
R
(SBW)
9.76 kΩ
SDA
OUT–
SBWTDIO
SBWTCK
Programming
EN
V
DD
C
(VDD)
1 µF
Li-ion
Captouch
Buttons
P2.0
P2.1
IN/TRIG
GND
AVSS
DVSS
Copyright © 2016, Texas Instruments Incorporated
Figure 60. Typical Application Schematic
9.2.1 Design Requirements
For this design example, use the values listed in Table 30 as the input parameters.
Table 30. Design Parameters
DESIGN PARAMETER
Interface
EXAMPLE VALUE
I2C, external trigger
Actuator type
LRA, ERM
Input power source
Li-ion/Li-polymer, 5-V boost
9.2.2 Detailed Design Procedure
9.2.2.1 Actuator Selection
The actuator decision is based on many factors including cost, form factor, vibration strength, power-
consumption requirements, haptic sharpness requirements, reliability, and audible noise performance. The
actuator selection is one of the most important design considerations of a haptic system and therefore the
actuator should be the first component to consider when designing the system. The following sections list the
basics of ERM and LRA actuators.
9.2.2.1.1 Eccentric Rotating-Mass Motors (ERM)
Eccentric rotating-mass motors (ERMs) are typically DC-controlled motors of the bar or coin type. ERMs can be
driven in the clockwise direction or counter-clockwise direction depending on the polarity of voltage across the
two pins. Bidirectional drive is made possible in a single-supply system by differential outputs that are capable of
sourcing and sinking current. The bidirectional drive feature helps eliminate long vibration tails which are
undesirable in haptic feedback systems.
Copyright © 2014–2018, Texas Instruments Incorporated
55
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
I
L
I
L
OUT+
OUT+
+
œ
Motor-spin
direction
Motor-spin
direction
V
V
O
O
œ
+
OUTœ
OUTœ
I
L
I
L
Figure 61. Motor Spin Direction in ERM Motors
Another common approach to driving DC motors is the concept of overdrive voltage. To overcome the inertia of
the mass of the motor, the DC motors are often overdriven for a short amount of time before returning to the
rated voltage of the motor to sustain the rotation of the motor. Overdrive is also used to stop (or brake) a motor
quickly. Refer to the data sheet of the particular motor used with the DRV2604L device for safe and reliable
overdrive voltage and duration.
9.2.2.1.2 Linear Resonance Actuators (LRA)
Linear resonant actuators (LRAs) vibrate optimally at the resonant frequency. LRAs have a high-Q frequency
response because of a rapid drop in vibration performance at the offsets of 3 to 5 Hz from the resonant
frequency. Many factors also cause a shift or drift in the resonant frequency of the actuator such as temperature,
aging, the mass of the product to which the LRA is mounted, and in the case of a portable product, the manner in
which the product is held. Furthermore, as the actuator is driven to the maximum allowed voltage, many LRAs
will shift several hertz in frequency because of mechanical compression. All of these factors make a real-time
tracking auto-resonant algorithm critical when driving LRA to achieve consistent, optimized performance.
Frequency (Hz)
ƒ
(RESONANCE)
Figure 62. Typical LRA Response
9.2.2.1.2.1 Auto-Resonance Engine for LRA
The DRV2604L auto-resonance engine tracks the resonant frequency of an LRA in real time effectively locking
into the resonance frequency after half a cycle. If the resonant frequency shifts in the middle of a waveform for
any reason, the engine tracks the frequency from cycle to cycle. The auto resonance engine accomplishes this
tracking by constantly monitoring the back-EMF of the actuator. Note that the auto resonance engine is not
affected by the auto-calibration process which is only used for level calibration. No calibration is required for the
auto resonance engine.
9.2.2.2 Capacitor Selection
The DRV2604L device has a switching output stage which pulls transient currents through the VDD pin. TI
recommends placing a 0.1-µF low equivalent-series-resistance (ESR) supply-bypass capacitor of the X5R or
X7R type near the VDD supply pin for proper operation of the output driver and the digital portion of the device.
Place a 1-µF X5R or X7R-type capacitor from the REG pin to ground.
56
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
9.2.2.3 Interface Selection
The I2C interface is required to configure the device. The device can be used fully with the I2C interface and with
either RTP or internal memory. The advantage of using the I2C interface is that no additional GPIO (for the
IN/TRIG pin) is required for firing effects, and no PWM signal is required to be generated. Therefore the IN/TRIG
pin can be connected to GND. Using the external trigger pin has the advantage that no I2C transaction is
required to fire the pre-loaded effect, which is a good choice for interfacing with a button. The PWM interface is
available for backward compatibility.
9.2.2.4 Power Supply Selection
The DRV2604L device supports a wide range of voltages in the input. Ensuring that the battery voltage is high
enough to support the desired vibration strength with the selected actuator is an important design consideration.
The typical application uses Li-ion or Li-polymer batteries which provide enough voltage headroom to drive most
common actuators.
If very strong vibrations are desired, a boost converter can be placed between the power supply and the VDD pin
to provide a constant voltage with a healthy headroom (5-V rails are common in some systems) which is
particularly true if two AA batteries in series are being used to power the system.
9.2.3 Application Curves
IN/TRIG
IN/TRIG
Acceleration
Acceleration
[OUT+] − [OUT−] (Filtered)
[OUT+] − [OUT−] (Filtered)
0
40m
80m
120m
Time (s)
160m
200m
0
40m
80m
120m
Time (s)
160m
200m
VDD = 3.6 V ERM open loop
VDD = 3.6 V LRA closed loop
Strong click
- 60%
External edge
trigger
Strong click -
100%
External level
trigger
Figure 63. ERM Click with and without Braking
Figure 64. LRA Click With and Without Braking
Copyright © 2014–2018, Texas Instruments Incorporated
57
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
9.3 Initialization Setup
9.3.1 Initialization Procedure
1. After powerup, wait at least 250 µs before the DRV2604L device accepts I2C commands.
2. Assert the EN pin (logic high). The EN pin can be asserted any time during or after the 250-µs wait period.
3. Write the MODE register (address 0x01) to value 0x00 to remove the device from standby mode.
4. If the nonvolatile auto-calibration memory has been programmed as described in the Auto Calibration
Procedure section, skip Step 5 and proceed to Step 6.
5. Perform the steps as described in the Auto Calibration Procedure section. Alternatively, rewrite the results
from a previous calibration.
6. If using the embedded RAM memory, populate the RAM with waveforms at this time as described in the
Loading Data to RAM section. Use registers 0xFD to 0xFF to access the RAM as described in the Table 2
procedure.
7. The default setup is closed-loop bidirectional mode. To use other modes and features, write Control1 (0x1B),
Control2 (0x1C), and Control3 (0x1D) as required.
8. Put the device in standby mode or deassert the EN pin, whichever is the most convenient. Both settings are
low-power modes. The user can select the desired MODE (address 0x01) at the same time the STANDBY
bit is set.
9.3.2 Typical Usage Examples
9.3.2.1 Play a Waveform or Waveform Sequence from the RAM Waveform Memory
1. Initialize the device as listed in the Initialization Procedure section.
2. Assert the EN pin (active high) if it was previously deasserted.
3. If register 0x01 already holds the desired value and the STANDBY bit is low, the user can skip this step.
Select the desired MODE[2:0] value of 0 (internal trigger), 1 (external edge trigger), or 2 (external level
trigger) in the MODE register (address 0x01). If the STANDBY bit was previously asserted, this bit should be
deasserted (logic low) at this time.
4. Select the waveform index to be played and write it to address 0x04. Alternatively, a sequence of waveform
indices can be written to register 0x04 through 0x0B. See the Waveform Sequencer section for details.
5. If using the internal trigger mode, set the GO bit (in register 0x0C) to fire the effect or sequence of effects. If
using an external trigger mode, send an appropriate trigger pulse to the IN/TRIG pin. See the Waveform
Triggers section for details.
6. If desired, the user can repeat Step 5 to fire the effect or sequence again.
7. Put the device in low-power mode by deasserting the EN pin or setting the STANDBY bit.
9.3.2.2 Play a Real-Time Playback (RTP) Waveform
1. Initialize the device as shown in the Initialization Procedure section.
2. Assert the EN pin (active high) if it was previously deasserted.
3. Set the MODE[2:0] value to 5 (RTP Mode) at address 0x01. If the STANDBY bit was previously asserted,
this bit should be deasserted (logic low) at this time. If register 0x01 already holds the desired value and the
STANDBY bit is low, the user can skip this step.
4. Write the desired drive amplitude to the real-time playback input register (address 0x02).
5. When the desired sequence of drive amplitudes is complete, put the device in low-power mode by
deasserting the EN pin or setting the STANDBY bit.
58
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
Initialization Setup (continued)
9.3.2.3 Play a PWM or Analog Input Waveform
1. Initialize the device as shown in the Initialization Procedure section.
2. Assert the EN pin (active high) if it was previously deasserted.
3. If register 0x01 already holds the desired value and the STANDBY bit is low, the user can skip this step. Set
the MODE value to 3 (PWM/Analog Mode) at address 0x01. If the STANDBY bit was previously asserted,
this bit should be deasserted (logic low) at this time.
4. Select the input mode (PWM or analog) in the Control3 register (address 0x1D). If this mode was selected
during the initialization procedure, the user can skip this step.
5. Send the desired PWM or analog input waveform sequence from the external source. See the Data Formats
for Waveform Playback section for drive amplitude scaling.
6. When the desired drive sequence is complete, put the device in low-power mode by deasserting the EN pin
or setting the STANDBY bit.
10 Power Supply Recommendations
The DRV2604L device is designed to operate from an input-voltage supply range between 2 V to 5.2 V. The
decoupling capacitor for the power supply should be placed closed to the device pin.
Copyright © 2014–2018, Texas Instruments Incorporated
59
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
11 Layout
11.1 Layout Guidelines
Use the following guidelines for the DRV2604L layout:
•
•
•
The decoupling capacitor for the power supply (VDD) should be placed closed to the device pin.
The filtering capacitor for the regulator (REG) should be placed close to the device REG pin.
When creating the pad size for the WCSP pins, TI recommends that the PCB layout use nonsolder mask-
defined (NSMD) land. With this method, the solder mask opening is made larger than the desired land area
and the opening size is defined by the copper pad width. Figure 65 shows and Table 31 lists appropriate
diameters for a wafer-chip scale package (WCSP) layout.
Copper
Trace Width
Solder
Pad Width
Solder Mask
Opening
Copper Trace
Thickness
Solder Mask
Thickness
Figure 65. Land Pattern Dimensions
Table 31. Land Pattern Dimensions
SOLDER PAD
DEFINITIONS
SOLDER MASK
OPENING
COPPER
THICKNESS
STENCIL
OPENING
STENCIL
THICKNESS
COPPER PAD
Nonsolder mask
defined (NSMD)
275 µm
(0, –25 µm)
375 µm
(0, –25 µm)
275 µm × 275 µm2
(rounded corners)
1-oz maximum (32 µm)
125-µm thick
1. Circuit traces from NSMD defined PWB lands should be 75-µm to 100-µm wide in the exposed area inside the solder
mask opening. Wider trace widths reduce device stand-off and impact reliability.
2. The recommended solder paste is Type 3 or Type 4.
3. The best reliability results are achieved when the PWB laminate glass transition temperature is above the operating the
range of the intended application.
4. For a PWB using a Ni/Au surface finish, the gold thickness should be less than 0.5 µm to avoid a reduction in thermal
fatigue performance.
5. Solder mask thickness should be less than 20 µm on top of the copper circuit pattern.
6. The best solder stencil performance is achieved using laser-cut stencils with electro polishing. Use of chemically-etched
stencils results in inferior solder paste volume control.
7. Trace routing away from the WCSP device should be balanced in X and Y directions to avoid unintentional component
movement because of solder-wetting forces.
60
Copyright © 2014–2018, Texas Instruments Incorporated
DRV2604L
www.ti.com.cn
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
11.1.1 Trace Width
The recommended trace width at the solder pins is 75 µm to 100 µm to prevent solder wicking onto wider PCB
traces. Maintain this trace width until the pin pattern has escaped, then the trace width can be increased for
improved current flow. The width and length of the 75-µm to 100-µm traces should be as symmetrical as possible
around the device to provide even solder reflow on each of the pins.
11.2 Layout Example
C(REG)
EN
IN
REG
SDA
OUT+
GND
Via
Via should connect
to a ground plane
V
SCL
OUTt
DD
C(VDD)
Figure 66. DRV2604L Layout Example DSBGA
C(REG)
C(VDD)
REG
SCL
SDA
VDD
OUT-
GND
Via
IN/TRIG
EN
OUT+
Via should connect
to a ground plane
VDD/NC
Figure 67. DRV2604L Layout Example VSSOP
版权 © 2014–2018, Texas Instruments Incorporated
61
DRV2604L
ZHCSDF4F –MAY 2014–REVISED MARCH 2018
www.ti.com.cn
12 器件和文档支持
12.1 文档支持
12.1.1 相关文档
如需相关文档,请参阅:
•
•
•
•
•
《触觉能耗》,SLOA194
《关于移动设备和可穿戴设备的触觉实现注意事项》,SLOA207
《LRA 致动器:如何移动它们?》,SLOA209
《DRV2604L ERM、LRA 触觉驱动器评估套件》,SLOU390
《DRV2604LDGS 触觉驱动器迷你板》,SLOU397
12.2 接收文档更新通知
要接收文档更新通知,请导航至 TI.com.cn 上的器件产品文件夹。请单击右上角的提醒我 进行注册,即可每周接收
产品信息更改摘要。有关更改的详细信息,请查阅已修订文档中包含的修订历史记录。
12.3 社区资源
下列链接提供到 TI 社区资源的连接。链接的内容由各个分销商“按照原样”提供。这些内容并不构成 TI 技术规范,
并且不一定反映 TI 的观点;请参阅 TI 的 《使用条款》。
TI E2E™ 在线社区 TI 的工程师对工程师 (E2E) 社区。此社区的创建目的在于促进工程师之间的协作。在
e2e.ti.com 中,您可以咨询问题、分享知识、拓展思路并与同行工程师一道帮助解决问题。
设计支持
TI 参考设计支持 可帮助您快速查找有帮助的 E2E 论坛、设计支持工具以及技术支持的联系信息。
12.4 商标
E2E is a trademark of Texas Instruments.
TouchSense is a registered trademark of Immersion Corporation.
All other trademarks are the property of their respective owners.
12.5 静电放电警告
ESD 可能会损坏该集成电路。德州仪器 (TI) 建议通过适当的预防措施处理所有集成电路。如果不遵守正确的处理措施和安装程序 , 可
能会损坏集成电路。
ESD 的损坏小至导致微小的性能降级 , 大至整个器件故障。 精密的集成电路可能更容易受到损坏 , 这是因为非常细微的参数更改都可
能会导致器件与其发布的规格不相符。
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 机械、封装和可订购信息
以下页面包含机械、封装和可订购信息。这些信息是指定器件的最新可用数据。数据如有变更,恕不另行通知,且
不会对此文档进行修订。如需获取此数据表的浏览器版本,请查阅左侧的导航栏。
62
版权 © 2014–2018, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
7-Feb-2023
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
DRV2604LDGSR
DRV2604LDGST
DRV2604LYZFR
DRV2604LYZFT
ACTIVE
ACTIVE
ACTIVE
ACTIVE
VSSOP
VSSOP
DSBGA
DSBGA
DGS
DGS
YZF
YZF
10
10
9
2500 RoHS & Green
250 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
NIPDAUAG | SN
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 85
-40 to 85
-40 to 85
-40 to 85
04L
Samples
Samples
Samples
Samples
NIPDAUAG | SN
SNAGCU
04L
2604L
2604L
9
SNAGCU
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
7-Feb-2023
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
12-May-2023
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
DRV2604LDGSR
DRV2604LDGSR
DRV2604LDGST
DRV2604LDGST
DRV2604LYZFR
DRV2604LYZFT
VSSOP
VSSOP
VSSOP
VSSOP
DSBGA
DSBGA
DGS
DGS
DGS
DGS
YZF
YZF
10
10
10
10
9
2500
2500
250
330.0
330.0
330.0
330.0
180.0
180.0
12.4
12.4
12.4
12.4
8.4
5.3
5.3
3.4
3.4
1.4
1.4
8.0
8.0
8.0
8.0
4.0
4.0
12.0
12.0
12.0
12.0
8.0
Q1
Q1
Q1
Q1
Q1
Q1
5.3
3.4
1.4
250
5.3
3.4
1.4
3000
250
1.65
1.65
1.65
1.65
0.81
0.81
9
8.4
8.0
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
12-May-2023
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
DRV2604LDGSR
DRV2604LDGSR
DRV2604LDGST
DRV2604LDGST
DRV2604LYZFR
DRV2604LYZFT
VSSOP
VSSOP
VSSOP
VSSOP
DSBGA
DSBGA
DGS
DGS
DGS
DGS
YZF
YZF
10
10
10
10
9
2500
2500
250
366.0
366.0
366.0
366.0
182.0
182.0
364.0
364.0
364.0
364.0
182.0
182.0
50.0
50.0
50.0
50.0
20.0
20.0
250
3000
250
9
Pack Materials-Page 2
PACKAGE OUTLINE
DGS0010A
VSSOP - 1.1 mm max height
S
C
A
L
E
3
.
2
0
0
SMALL OUTLINE PACKAGE
C
SEATING PLANE
0.1 C
5.05
4.75
TYP
PIN 1 ID
AREA
A
8X 0.5
10
1
3.1
2.9
NOTE 3
2X
2
5
6
0.27
0.17
10X
3.1
2.9
1.1 MAX
0.1
C A
B
B
NOTE 4
0.23
0.13
TYP
SEE DETAIL A
0.25
GAGE PLANE
0.15
0.05
0.7
0.4
0 - 8
DETAIL A
TYPICAL
4221984/A 05/2015
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
5. Reference JEDEC registration MO-187, variation BA.
www.ti.com
EXAMPLE BOARD LAYOUT
DGS0010A
VSSOP - 1.1 mm max height
SMALL OUTLINE PACKAGE
10X (1.45)
(R0.05)
TYP
SYMM
10X (0.3)
1
5
10
SYMM
6
8X (0.5)
(4.4)
LAND PATTERN EXAMPLE
SCALE:10X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
0.05 MAX
ALL AROUND
0.05 MIN
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
NOT TO SCALE
4221984/A 05/2015
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DGS0010A
VSSOP - 1.1 mm max height
SMALL OUTLINE PACKAGE
10X (1.45)
SYMM
(R0.05) TYP
10X (0.3)
8X (0.5)
1
5
10
SYMM
6
(4.4)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:10X
4221984/A 05/2015
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
PACKAGE OUTLINE
YZF0009
DSBGA - 0.625 mm max height
SCALE 8.000
DIE SIZE BALL GRID ARRAY
A
B
E
BALL A1
CORNER
D
C
0.625 MAX
SEATING PLANE
0.05 C
BALL TYP
0.35
0.15
1 TYP
SYMM
C
1
TYP
SYMM
B
A
D: Max = 1.47 mm, Min = 1.41 mm
E: Max = 1.47 mm, Min = 1.41 mm
0.5
TYP
3
1
2
0.35
0.25
9X
0.015
0.5 TYP
C A B
4219558/A 10/2018
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
www.ti.com
EXAMPLE BOARD LAYOUT
YZF0009
DSBGA - 0.625 mm max height
DIE SIZE BALL GRID ARRAY
(0.5) TYP
9X ( 0.245)
(0.5) TYP
1
2
3
A
SYMM
B
C
SYMM
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 40X
0.05 MIN
0.05 MAX
METAL UNDER
SOLDER MASK
(
0.245)
METAL
(
0.245)
EXPOSED
METAL
SOLDER MASK
OPENING
EXPOSED
METAL
SOLDER MASK
OPENING
SOLDER MASK
DEFINED
NON-SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
NOT TO SCALE
4219558/A 10/2018
NOTES: (continued)
3. Final dimensions may vary due to manufacturing tolerance considerations and also routing constraints.
See Texas Instruments Literature No. SNVA009 (www.ti.com/lit/snva009).
www.ti.com
EXAMPLE STENCIL DESIGN
YZF0009
DSBGA - 0.625 mm max height
DIE SIZE BALL GRID ARRAY
(0.5) TYP
(R0.05) TYP
3
9X ( 0.25)
1
2
A
B
(0.5) TYP
SYMM
METAL
TYP
C
SYMM
SOLDER PASTE EXAMPLE
BASED ON 0.1 mm THICK STENCIL
SCALE: 40X
4219558/A 10/2018
NOTES: (continued)
4. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023,德州仪器 (TI) 公司
相关型号:
©2020 ICPDF网 联系我们和版权申明