BQ29700 [TI]
BQ297xx Cost-Effective Voltage and Current Protection Integrated Circuit for Single-Cell Li-Ion and Li-Polymer Batteries;型号: | BQ29700 |
厂家: | TEXAS INSTRUMENTS |
描述: | BQ297xx Cost-Effective Voltage and Current Protection Integrated Circuit for Single-Cell Li-Ion and Li-Polymer Batteries |
文件: | 总32页 (文件大小:1964K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
BQ2970, BQ2971, BQ2972, BQ2973
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
BQ297xx Cost-Effective Voltage and Current Protection Integrated Circuit for Single-Cell
Li-Ion and Li-Polymer Batteries
1 Features
2 Applications
1
•
•
Input voltage range pack+: VSS – 0.3 V to 12 V
FET drive:
•
•
•
Tablet PCs
Mobile handsets
Handheld data terminals
–
CHG and DSG FET drive output
•
•
Voltage sensing across external FETs for
overcurrent protection (OCP) is within ±5 mV
(typical)
3 Description
The BQ2970 battery cell protection device provides
an accurate monitor and trigger threshold for
overcurrent protection during high discharge/charge
current operation or battery overcharge conditions.
Fault detection
–
–
–
–
–
Overcharge detection (OVP)
Over-discharge detection (UVP)
Charge overcurrent detection (OCC)
Discharge overcurrent detection (OCD)
Load short-circuit detection (SCP)
The BQ2970 device provides the protection functions
for li-ion/li-polymer cells, and monitors across the
external power FETs for protection due to high
charge or discharge currents. In addition, there is
overcharge and depleted battery monitoring and
protection. These features are implemented with low
current consumption in NORMAL mode operation.
•
•
Zero voltage charging for depleted battery
Factory programmed fault protection thresholds
–
–
–
Fault detection voltage thresholds
Fault trigger timers
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
Fault recovery timers
BQ2970, BQ2971,
BQ2972, BQ2973(2)
WSON (6)
1.50 mm × 1.50 mm
•
Modes of operation without battery charger
enabled
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
–
–
NORMAL mode ICC = 4 µA
Shutdown Iq = 100 nA
(2) For available released devices, see the Device Comparison
Table.
•
•
Operating temperature range TA = –40°C to
+85°C
Package:
–
6-pin DSE (1.50 mm × 1.50 mm × 0.75 mm)
Simplified Schematic
OCD Detection Accuracy Versus Temperature
PACK+
0.0
œ0.5
œ1.0
œ1.5
œ2.0
œ2.5
œ3.0
œ3.5
œ4.0
V–
NC
330
BAT
VSS
COUT
DOUT
CELLP
CELLN
2.2k
PACK–
D
S
S
CHG
DSG
0
20
40
60
80
100
120
œ40
œ20
Temperature (°C)
C012
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. UNLESS OTHERWISE NOTED, this document contains PRODUCTION
DATA.
BQ2970, BQ2971, BQ2972, BQ2973
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
www.ti.com
Table of Contents
1
2
3
4
5
6
Features.................................................................. 1
Applications ........................................................... 1
Description ............................................................. 1
Revision History..................................................... 2
Device Comparison Table..................................... 3
Pin Configuration and Functions......................... 3
6.1 Pin Descriptions ........................................................ 4
Specifications......................................................... 4
7.1 Absolute Maximum Ratings ...................................... 4
7.2 ESD Ratings.............................................................. 5
7.3 Recommended Operating Conditions....................... 5
7.4 Thermal Information.................................................. 5
7.5 DC Characteristics .................................................... 5
7.6 Programmable Fault Detection Thresholds ............. 6
7.7 Programmable Fault Detection Timer Ranges ........ 6
7.8 Typical Characteristics.............................................. 7
Parameter Measurement Information ................ 10
8.1 Timing Charts.......................................................... 10
8.2 Test Circuits ............................................................ 12
8.3 Test Circuit Diagrams ............................................. 14
9
Detailed Description ............................................ 14
9.1 Overview ................................................................. 14
9.2 Functional Block Diagram ....................................... 15
9.3 Feature Description ................................................ 15
9.4 Device Functional Modes........................................ 15
10 Application and Implementation........................ 19
10.1 Application Information.......................................... 19
10.2 Typical Application ................................................ 19
11 Power Supply Recommendations ..................... 22
12 Layout................................................................... 22
12.1 Layout Guidelines ................................................ 22
12.2 Layout Example .................................................... 22
13 Device and Documentation Support ................. 23
13.1 Related Documentation......................................... 23
13.2 Related Links ........................................................ 23
13.3 Support Resources ............................................... 23
13.4 Trademarks........................................................... 23
13.5 Electrostatic Discharge Caution............................ 23
13.6 Glossary................................................................ 23
7
8
14 Mechanical, Packaging, and Orderable
Information ........................................................... 23
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision F (December 2018) to Revision G
Page
•
Changed the Device Comparison Table................................................................................................................................. 3
Changes from Revision E (May 2018) to Revision F
Page
•
•
Changed the BQ29728 device to Production Data ................................................................................................................ 3
Added the BQ29737 device.................................................................................................................................................... 3
Changes from Revision D (May 2016) to Revision E
Page
•
•
Changed 0-V Charging Function Enabled ........................................................................................................................... 17
Changed 0-V Charging Inhibit Function .............................................................................................................................. 17
Changes from Revision C (March 2016) to Revision D
Page
•
Changed BQ29733 to released in the Device Comparison Table. ........................................................................................ 3
Changes from Revision B (November, 2015) to Revision C
Page
•
•
•
•
Added the device numbers BQ2971, BQ2972, BQ2973. Changed document title to BQ297xx............................................ 1
Added BQ29708~BQ29733 to the Device Comparison Table. Clarified recovery delay and moved info to footnote 2 ........ 3
Changed UVP release voltage value based on 100-mV hysteresis from UVP threshold.................................................... 19
Added Related Links table.................................................................................................................................................... 23
2
Submit Documentation Feedback
Copyright © 2014–2020, Texas Instruments Incorporated
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
www.ti.com
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
Changes from Revision A (June, 2014) to Revision B
Page
•
•
Changed the device number to BQ2970 ............................................................................................................................... 1
Deleted the Related Links table from the Device and Documentation Support section....................................................... 23
5 Device Comparison Table
UVP
DELAY
(ms)
OCC
DELAY
(ms)
OCD
DELAY
(ms)
PART
OVP
DELAY (s)
SCD DELAY
(µs)
OVP (V)
UVP (V)
OCC (V)
OCD (V)
SCD (V)
NUMBER(1)
BQ29700
BQ29701
BQ29702
BQ29703
BQ29704
BQ29705
BQ29706
BQ29707
BQ29716
BQ29717
BQ29718
BQ29723
BQ29728(2)
BQ29729
BQ29732
BQ29733
BQ29737(2)
4.275
4.280
4.350
4.425
4.425
4.425
3.850
4.280
4.425
4.425
4.425
4.425
4.280
4.275
4.280
4.400
4.250
1.25
1.25
1
2.800
2.300
2.800
2.300
2.500
2.500
2.500
2.800
2.300
2.500
2.500
2.500
2.800
2.300
2.500
2.800
2.800
144
144
96
–0.100
–0.100
–0.155
–0.100
–0.100
–0.100
–0.150
–0.090
–0.100
–0.100
–0.100
–0.060
–0.100
–0.100
–0.100
–0.100
-0.050
8
8
8
8
8
8
8
6
8
8
8
4
8
8
8
8
16
0.100
0.125
0.160
0.160
0.125
0.150
0.200
0.090
0.165
0.130
0.100
0.100
0.150
0.130
0.190
0.120
0.100
20
8
0.5
0.5
0.3
0.5
0.5
0.5
0.6
0.3
0.5
0.5
0.5
0.3
0.5
0.5
0.5
0.3
0.3
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
16
8
1.25
1.25
1.25
1.25
1
20
20
8
20
8
144
96
8
16
8
1.25
1.25
1.25
1
20
20
8
20
8
96
8
1.25
1.25
1.25
1.25
1
144
20
8
8
144
20
8
8
96
16
0.25, 1,
1.25, 4.5
20, 96, 125, –0.045 to
144 –0.155
8, 16, 20,
48
0.3, 0.4,
0.5, 0.6
BQ297xy
3.85–4.6
2.0–2.8
4, 6, 8, 16
0.090–0.200
250
(1) All of the protections have a recovery delay time. The recovery timer starts as soon as the fault is triggered. The device starts to check
for a recovery condition only when the recovery timer expires. This is NOT a delay time between recovery condition to FETs recovery.
OVP recovery delay = 12 ms; UVP/OCC/OCD recovery delay = 8 ms.
(2) Contact TI for more information.
6 Pin Configuration and Functions
DSE Package
6-PIN WSON
Top View
NC
COUT
DOUT
1
2
3
6
5
4
V–
BAT
VSS
Pin Functions
DESCRIPTION
VDD pin
PIN
TYPE
NAME
BAT
NO.
5
P
COUT
2
O
Gate Drive Output for Charge FET
Copyright © 2014–2020, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
www.ti.com
Pin Functions (continued)
PIN
TYPE
DESCRIPTION
NAME
DOUT
NC
NO.
3
O
NC
P
Gate Drive Output for Discharge FET
No Connection (electrically open, do not connect to BAT or VSS)
Ground pin
1
VSS
V–
4
6
I/O
Input pin for charger negative voltage
6.1 Pin Descriptions
6.1.1 Supply Input: BAT
This pin is the input supply for the device and is connected to the positive terminal of the battery pack. A 0.1-µF
input capacitor is connected to ground for filtering noise.
6.1.2 Cell Negative Connection: VSS
This pin is an input to the device for cell negative ground reference. Internal circuits associated with cell voltage
measurements and overcurrent protection input to differential amplifier for either Vds sensing or external sense
resistor sensing will be referenced to this node.
6.1.3 Voltage Sense Node: V–
This is a sense node used for measuring several fault detection conditions, such as overcurrent charging or
overcurrent discharging configured as Vds sensing for protection. This input, in conjunction with VSS, forms the
differential measurement for the stated fault detection conditions. A 2.2-kΩ resistor is connected between this
input pin and Pack– terminal of the system in the application.
6.1.4 Discharge FET Gate Drive Output: DOUT
This pin is an output to control the discharge FET. The output is driven from an internal circuitry connected to the
BAT supply. This output transitions from high to low when a fault is detected, and requires the DSG FET to turn
OFF. A 5-MΩ high impedance resistor is connected from DOUT to VSS for gate capacitance discharge when the
FET is turned OFF.
6.1.5 Charge FET Gate Drive Output: COUT
This pin is an output to control the charge FET. The output is driven from an internal circuitry connected to the
BAT supply. This output transitions from high to low when a fault is detected, and requires the CHG FET to turn
OFF. A 5-MΩ high impedance resistor is connected from COUT to Pack– for gate capacitance discharge when
FET is turned OFF.
7 Specifications
7.1 Absolute Maximum Ratings(1)
MIN
–0.3
MAX
12
UNIT
V
Input voltage: BAT
Supply control and input
V– pin(pack–)
BAT – 28
VSS – 0.3
BAT – 28
–40
BAT + 0.3
BAT + 0.3
BAT + 0.3
85
V
DOUT (Discharge FET Output), GDSG (Discharge FET Gate Drive)
V
FET drive and protection COUT (Charge FET Output), GCHG (Charge FET Gate Drive)
Operating temperature: TFUNC
V
°C
°C
Storage temperature, Tstg
–55
150
(1) Stresses beyond those listed under Absolute Maximum Ratings can cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods can affect device reliability.
4
Submit Documentation Feedback
Copyright © 2014–2020, Texas Instruments Incorporated
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
www.ti.com
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
7.2 ESD Ratings
VALUE
UNIT
Human body model (HBM), per ANSI/ESDA/JEDEC JS–001, all pins(2)
±2000
Electrostatic
Discharge
(1)
VESD
V
Charged device model (CDM), per JEDEC specification JESD22-C101, all
pins(3)
±500
(1) Electrostatic discharge (ESD) to measure device sensitivity and immunity to damage caused by assembly line electrostatic discharges
into the device.
(2) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Pins listed as 1000 V
can have higher performance.
(3) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Pins listed as 250 V
can have higher performance.
7.3 Recommended Operating Conditions(1)
MIN
–0.3
MAX
8
UNIT
V
Positive input voltage: BAT
Supply control and
input
Negative input voltage: V–
BAT – 25
VSS
BAT
BAT
BAT
85
V
Discharge FET control: DOUT
Charge FET control: COUT
V
FET drive and
protection
BAT – 25
–40
V
Operating temperature: TAmb
Storage temperature: TS
°C
°C
°C
°C/W
–55
150
300
250
Temperature Ratings
Lead temperature (soldering 10 s)
Thermal resistance junction to ambient, θJA
(1)
(1) For more information about traditional and new thermal metrics, see the IC package Thermal Metrics application report, SPRA953.
7.4 Thermal Information
BQ297xx
THERMAL METRIC(1)
DSE (WSON)
12 PINS
190.5
UNIT
RθJA, High K
RθJC(top)
RθJB
Junction-to-ambient thermal resistance
Junction-to-case(top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
94.9
149.3
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case(bottom) thermal resistance
6.4
ψJB
152.8
RθJC(bottom)
N/A
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
7.5 DC Characteristics
Typical Values stated where TA = 25°C and BAT = 3.6 V. Min/Max values stated where TA = –40°C to 85°C, and BAT = 3 V
to 4.2 V (unless otherwise noted)
PARAMETER
Current consumption
TEST CONDITIONS
MIN
TYP
MAX UNIT
BAT – VSS
BAT – V–
1.5
1.5
8
V
VBAT
Device operating range
28
INORMAL
Current consumption in NORMAL mode
BAT = 3.8 V, V– = 0 V
4
5.5
0.1
µA
µA
IPower_down Current consumption in power down mode BAT = V– = 1.5 V
FET Output, DOUT and COUT
VOL
VOH
VOL
VOH
Charge FET low output
Charge FET high output
Discharge FET low output
Discharge FET high output
IOL = 30 µA, BAT = 3.8 V
IOH = –30 µA, BAT = 3.8 V
IOL = 30 µA, BAT = 2 V
IOH = –30 µA, BAT = 3.8 V
0.4
3.7
0.2
3.7
0.5
0.5
V
V
V
V
3.4
3.4
Pullup Internal Resistance on V–
Copyright © 2014–2020, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
www.ti.com
DC Characteristics (continued)
Typical Values stated where TA = 25°C and BAT = 3.6 V. Min/Max values stated where TA = –40°C to 85°C, and BAT = 3 V
to 4.2 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VBAT = 1.8 V, V– = 0 V
MIN
TYP
MAX UNIT
RV–D
Resistance between V– and VBAT
100
300
550
24
kΩ
Current sink on V–
IV–S
Current sink on V– to VSS
VBAT = 3.8 V
8
µA
Load short detection on V–
VBAT
1 V
–
Vshort
Short detection voltage
VBAT = 3.8 V and RPackN = 2.2 kΩ
0-V battery charging function allowed
0-V battery charging function disallowed
V
V
V
0-V battery charge function
V0CHG
0-V battery charging start voltage
1.7
0-V battery charge inhibit function
0-V battery charging inhibit voltage
threshold
V0INH
0.75
7.6 Programmable Fault Detection Thresholds
PARAMETER
CONDITION
MIN
TYP
MAX UNIT
TA = 25°C
–10
10
mV
Factory Device Configuration: 3.85 V to
4.60 V in 50-mV steps
VOVP
Overcharge detection voltage
TA = 0°C to
60°C
–20
20
mV
Overcharge release hysteresis 100 mV and (VSS – V–) > OCC (min) for release, TA
=
VOVP–Hys
VUVP
–20
–50
20
50
mV
mV
voltage
25°C
Over-discharge detection
voltage
Factory Device Configuration: 2.00 V to 2.80 V in 50-mV
steps, TA = 25°C
Over-discharge release
hysteresis voltage
VUVP+Hys
100 mV and (BAT – V–) > 1 V for release, TA = 25°C
–50
–10
–15
50
10
15
mV
mV
mV
TA = 25°C
Discharging overcurrent
detection voltage
Factory Device Configuration: 90 mV to
200 mV in 5-mV steps
VOCD
TA = –40°C to
85°C
Release when BAT – V– > 1 V
TA = 25°C
Release of
VOCD
Release of discharging
overcurrent detection voltage
1
V
–10
–15
10
15
mV
mV
Charging overcurrent detection Factory Device Configuration: –45 mV to
voltage
VOCC
TA = –40°C to
85°C
–155 mV in 5-mV steps
Release of
VOCC
Release of overcurrent
detection voltage
Release when VSS – V– ≥ OCC (min)
40
1
mV
mV
V
Factory Device Configuration: 300 mV,
400 mV, 500 mV, 600 mV
VSCC
Short Circuit detection voltage
TA = 25°C
–100
100
Release of Short Circuit
detection voltage
VSCCR
Release when BAT – V– ≥ 1 V
7.7 Programmable Fault Detection Timer Ranges
PARAMETER
CONDITION
MIN
TYP
MAX UNIT
tOVPD
tUVPD
Overcharge detection delay time Factory Device Configuration: 0.25 s, 1 s, 1.25 s, 4.5 s
–20%
20%
s
Over-discharge detection delay
time
Factory Device Configuration: 20 ms, 96 ms, 125 ms, 144
ms
–20%
20%
ms
Discharging overcurrent detection
delay time
tOCDD
Factory Device Configuration: 8 ms, 16 ms, 20 ms, 48 ms –20%
20%
ms
Charging overcurrent detection
delay time
tOCCD
tSCCD
Factory Device Configuration: 4 ms, 6 ms, 8 ms, 16 ms
–20%
–50%
20%
50%
ms
µs
Short Circuit detection delay time 250 µs (fixed)
6
Submit Documentation Feedback
Copyright © 2014–2020, Texas Instruments Incorporated
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
www.ti.com
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
7.8 Typical Characteristics
6
5
4
3
2
1
0
0.050
0.045
0.040
0.035
0.030
0.025
0.020
0.015
0.010
0.005
0.000
0
20
40
60
80
100
120
œ40
œ20
0
20
40
60
80
100
120
œ40
œ20
Temperature (°C)
Temperature (°C)
C002
C001
VBAT = 3.9 V
VBAT = 1.5 V
Figure 2. 3.9-V IBAT Versus Temperature
Figure 1. 1.5-V IBAT Versus Temperature
1.34
1.32
1.30
1.28
1.26
1.24
1.22
1.20
1.18
œ1.32
œ1.34
œ1.36
œ1.38
œ1.40
œ1.42
œ1.44
œ1.46
0
20
40
60
80
100
120
0
20
40
60
80
100
120
œ40
œ20
œ40
œ20
Temperature (°C)
Temperature (°C)
C003
C004
FOSC, Setting = 1.255 kHz
VBAT, Setting = 0 V
Figure 3. Internal Oscillator Frequency Versus Temperature
Figure 4. 0-V Charging Allowed Versus Temperature
0.75
4
2
0
0.70
0.65
0.60
0.55
0.50
0.45
0.40
œ2
œ4
œ6
œ8
œ10
œ12
0
20
40
60
80
100
120
0
20
40
60
80
100
120
œ40
œ20
œ40
œ20
Temperature (°C)
Temperature (°C)
C005
C006
OVP, Setting = 4.275 V
Figure 5. 0-V Charging Disallowed Versus Temperature
Figure 6. OVP Detection Accuracy Versus Temperature
Copyright © 2014–2020, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
www.ti.com
Typical Characteristics (continued)
1350
0
œ2
1300
1250
1200
1150
1100
œ4
œ6
œ8
œ10
œ12
0
20
40
60
80
100
120
0
20
40
60
80
100
120
œ40
œ20
œ40
œ20
Temperature (°C)
Temperature (°C)
C007
C008
tOVPD, Setting = 1.25 s
UVP, Setting = 2.800 V
Figure 7. OVP Detection Dely Time Versus Temperature
Figure 8. UVP Detection Accuracy Versus Temperature
160
0.0
œ0.2
œ0.4
œ0.6
œ0.8
œ1.0
œ1.2
œ1.4
œ1.6
œ1.8
155
150
145
140
135
130
0
20
40
60
80
100
120
0
20
40
60
80
100
120
œ40
œ20
œ40
œ20
Temperature (°C)
Temperature (°C)
C009
C010
tUVPD, Setting = 144 ms
VOCC, Setting = –100 mV
Figure 9. UVP Detection Delay Time Versus Temperature
Figure 10. OCC Detection Accuracy Versus Temperature
8.6
0.0
8.4
8.2
8.0
7.8
7.6
7.4
7.2
7.0
œ0.5
œ1.0
œ1.5
œ2.0
œ2.5
œ3.0
œ3.5
œ4.0
0
20
40
60
80
100
120
0
20
40
60
80
100
120
œ40
œ20
œ40
œ20
Temperature (°C)
Temperature (°C)
C011
C012
tOCCD, Setting = 8 ms
VOCD, Setting = 100 mV
Figure 11. OCC Detection Delay Time Versus Temperature
Figure 12. OCD Detection Accuracy Versus Temperature
8
Submit Documentation Feedback
Copyright © 2014–2020, Texas Instruments Incorporated
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
www.ti.com
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
Typical Characteristics (continued)
22.5
22.0
21.5
21.0
20.5
20.0
19.5
19.0
18.5
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0
20
40
60
80
100
120
0
20
40
60
80
100
120
œ40
œ20
œ40
œ20
Temperature (°C)
Temperature (°C)
C013
C014
tUVPD, Setting = 20 ms
VSCC, Setting = 500 mV
Figure 13. OCD Detection Delay Time Versus Temperature
Figure 14. SCC Detection Accuracy Versus Temperature
1.24
3.795
1.22
1.20
1.18
1.16
1.14
1.12
1.10
3.790
3.785
3.780
3.775
3.770
3.765
0
20
40
60
80
100
120
0
20
40
60
80
100
120
œ40
œ20
œ40
œ20
Temperature (°C)
Temperature (°C)
C015
C016
VBAT, Setting = 3.9 V
Figure 15. Power On Reset Versus Temperature
Figure 16. COUT Versus Temperature with Ioh = –30 µA
3.7160
3.7155
3.7150
3.7145
3.7140
3.7135
0
20
40
60
80
100
120
œ40
œ20
Temperature (°C)
C017
VBAT, Setting = 3.9 V
Figure 17. DOUT Versus Temperature with Ioh = –30 µA
Copyright © 2014–2020, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
www.ti.com
8 Parameter Measurement Information
8.1 Timing Charts
Over-
Discharge
Normal
Overcharge
Normal
Normal
V
OVP
V
OVP– Hys
V
UVP– Hys
V
UVP
BAT
V
SS
BAT
V
SS
PACK–
BAT
V
OCD
V
SS
PACK–
t
UVPD
t
OVPD
Charger
Connected
Load
Connected
Charger
Connected
Figure 18. Overcharge Detection, Over-Discharge Detection
10
Submit Documentation Feedback
Copyright © 2014–2020, Texas Instruments Incorporated
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
www.ti.com
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
Timing Charts (continued)
Normal
Discharge Overcurrent
Normal
Discharge Overcurrent
Normal
V
OVP
V
OVP–Hys
V
UVP+Hys
V
UVP
BAT
VSS
BAT
VSS
PACK–
BAT
V
SCC
V
OCD
VSS
t
OCDD
t
SCCD
Load
Connected
Load
Disconnected
Load Short-
Circuit
Figure 19. Discharge Overcurrent Detection
Copyright © 2014–2020, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
www.ti.com
8.2 Test Circuits
The following tests are referenced as follows: The COUT and DOUT outputs are “H,” which are higher than the
threshold voltage of the external logic level FETs and regarded as ON state. “L” is less than the turn ON
threshold for external NMOS FETs and regarded as OFF state. The COUT pin is with respect to V–, and the
DOUT pin is with respect to VSS.
1. Overcharge detection voltage and overcharge release voltage (Test Circuit 1):
The overcharge detection voltage (VOVP) is measured between the BAT and VSS pins, respectively. Once V1
is increased, the over-detection is triggered, and the delay timer expires. Then, COUT transitions from a high
to low state and reduces the V1 voltage to check for the overcharge hysteresis parameter (VOVP-Hys). The
delta voltage between overcharge detection voltages (VOVP) and the overcharge release occurs when the
CHG FET drive output goes from low to high.
2. Over-discharge detection voltage and over-discharge release voltage (Test Circuit 2):
Over-discharge detection (VUVP) is defined as the voltage between BAT and VSS at which the DSG drive
output goes from high to low by reducing the V1 voltage. V1 is set to 3.5 V and gradually reduced while V2 is
set to 0 V. The over-discharge release voltage is defined as the voltage between BAT and VSS at which the
DOUT drive output transition from low to high when V1 voltage is gradually increased from a VUVP condition.
The overcharge hysteresis voltage is defined as the delta voltage between VUVP and the instance at which
the DOUT output drive goes from low to high.
3. Discharge overcurrent detection voltage (Test Circuit 2):
The discharge overcurrent detection voltage (VOCD) is measured between V– and VSS pins and triggered
when the V2 voltage is increased above VOCD threshold with respect to VSS. This delta voltage once
satisfied will trigger an internal timer tOCDD before the DOUT output drive transitions from high to low.
4. Load short circuit detection voltage (Test Circuit 2):
Load short-circuit detection voltage (VSCC) is measured between V– and VSS pins and triggered when the V2
voltage is increased above VSCC threshold with respect to VSS within 10 µs. This delta voltage, once
satisfied, triggers an internal timer tSCCD before the DOUT output drive transitions from high to low.
5. Charge overcurrent detection voltage (Test Circuit 2):
The charge overcurrent detection voltage (VOCC) is measured between VSS and V– pins and triggered when
the V2 voltage is increased above VOCC threshold with respect to V–. This delta voltage, once satisfied,
triggers an internal timer tOCCD before the COUT output drive transitions from high to low.
6. Operating current consumption (Test Circuit 2):
The operating current consumption IBNORMAL is the current measured going into the BAT pin under the
following conditions: V1 = 3.9 V and V2 = 0 V.
7. Power down current consumption (Test Circuit 2):
The operating current consumption IPower_down is the current measured going into the BAT pin under the
following conditions: V1 = 1.5 V and V2 = 1.5 V.
8. Resistance between V– and BAT pin (Test Circuit 3):
Measure the resistance (RV_D) between V– and BAT pins by setting the following conditions: V1 = 1.8 V and
V2 = 0 V.
9. Current sink between V– and VSS (Test Circuit 3):
Measure the current sink IV–S between V– and VSS pins by setting the following condition: V1 = 4 V.
10. COUT current source when activated High (Test Circuit 4):
Measure ICOUT current source on the COUT pin by setting the following conditions: V1 = 3.9 V, V2 = 0 V, and
V3 = 3.4 V.
11. COUT current sink when activated Low (Test Circuit 4):
Measure ICOUT current sink on COUT pin by setting the following conditions: V1 = 4.5 V, V2 = 0 V, and V3 =
0.5 V.
12
Submit Documentation Feedback
Copyright © 2014–2020, Texas Instruments Incorporated
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
www.ti.com
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
Test Circuits (continued)
12. DOUT current source when activated High (Test Circuit 4):
Measure IDOUT current source on DOUT pin by setting the following conditions: V1 = 3.9 V, V2 = 0 V, and V3
= 3.4 V.
13. DOUT current sink when activated Low (Test Circuit 4):
Measure IDOUT current sink on DOUT pin by setting the following conditions: V1 = 2.0 V, V2 = 0 V, and V3 =
0.4 V.
14. Overcharge detection delay (Test Circuit 5):
The overcharge detection delay time tOVPD is the time delay before the COUT drive output transitions from
high to low once the voltage on V1 exceeds the VOVP threshold. Set V2 = 0 V and then increase V1 until BAT
input exceeds the VOVP threshold, then check the time for when COUT goes from high to low.
15. Over-discharge detection delay (Test Circuit 5):
The over-discharge detection delay time tUVPD is the time delay before the DOUT drive output transitions
from high to low once the voltage on V1 decreases to VUVP threshold. Set V2 = 0 V and then decrease V1
until BAT input reduces to the VUVPthreshold, then check the time of when DOUT goes from high to low.
16. Discharge overcurrent detection delay (Test Circuit 5):
The discharge overcurrent detection delay time tOCDD is the time for DOUT drive output to transition from
high to low after the voltage on V2 is increased from 0 V to 0.35 V. V1 = 3.5 V and V2 starts from 0 V and
increases to trigger threshold.
17. Load short circuit detection delay (Test Circuit 5):
The load short-circuit detection delay time tSCCD is the time for DOUT drive output to transition from high to
low after the voltage on V2 is increased from 0 V to V1 – 1 V. V1 = 3.5 V and V2 starts from 0 V and
increases to trigger threshold.
18. Charge overcurrent detection delay (Test Circuit 5):
The charge overcurrent detection delay time tOCCD is the time for COUT drive output to transition from high to
low after the voltage on V2 is decreased from 0 V to –0.3 V. V1 = 3.5 V and V2 starts from 0 V and
decreases to trigger threshold.
19. 0-V battery charge starting charger voltage (Test Circuit 2):
The 0-V charge for start charging voltage V0CHA is defined as the voltage between BAT and V– pins at which
COUT goes high when voltage on V2 is gradually decreased from a condition of V1 = V2 = 0 V.
20. 0-V battery charge inhibition battery voltage (Test Circuit 2):
The 0-V charge inhibit for charger voltage V0INH is defined as the voltage between BAT and VSS pins at
which COUT should go low as V1 is gradually decreased from V1 = 2 V and V2 = –4 V.
Copyright © 2014–2020, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
www.ti.com
8.3 Test Circuit Diagrams
V-
6
5
4
V-
6
5
4
1
2
3
NC
1
2
3
NC
I
BAT
220Ω
V2
COUT
DOUT
BAT
VSS
COUT
DOUT
BAT
VSS
A
V
COUT
V
VCOUT V
V1
V1
V
V
V
DOUT
V
DOUT
Figure 20. Test Circuit 1
Figure 21. Test Circuit 2
I
V-
V-
6
5
4
V-
6
5
4
A
1
2
3
NC
1
2
3
NC
I
COUT
I
BAT
V2
V2
A
COUT
DOUT
BAT
VSS
COUT
DOUT
BAT
VSS
A
I
DOUT
V3
A
V1
V1
V4
Figure 22. Test Circuit 3
Figure 23. Test Circuit 4
V-
6
5
4
1
2
3
NC
Oscilloscope
Oscilloscope
V2
COUT
DOUT
BAT
VSS
V1
Figure 24. Test Circuit 5
9 Detailed Description
9.1 Overview
This BQ2970 device is a primary protector for a single-cell Li-Ion/Li-Polymer battery pack. The device uses a
minimum number of external components to protect for overcurrent conditions due to high discharge/charge
currents in the application. In addition, it monitors and helps to protect against battery pack overcharging or
depletion of energy in the pack. The BQ2970 device is capable of having an input voltage of 8 V from a charging
adapter and can tolerate a voltage of BAT – 25 V across the two input pins. In the condition when a fault is
triggered, there are timer delays before the appropriate action is taken to turn OFF either the CHG or DSG FETs.
The recovery period also has a timer delay once the threshold for recovery condition is satisfied. These
parameters are fixed once they are programmed. There is also a feature called zero voltage charging that
enables depleted cells to be charged to an acceptable level before the battery pack can be used for normal
operation. Zero voltage charging is allowed if the charger voltage is above 1.7 V. For Factory Programmable
Options, see Table 1.
Table 1. Factory Programmable Options
PARAMETER
FACTORY DEVICE CONFIGURATION
3.85 V to 4.60 V in 50-mV steps
VOVP
VUVP
VOCD
VOCC
VSCC
tOVPD
tUVPD
tOCDD
Overcharge detection voltage
Over-discharge detection voltage
Discharging overcurrent detection voltage
Charging overcurrent detection voltage
Short Circuit detection voltage
2.00 V to 2.80 V in 50-mV steps
90 mV to 200 mV in 5-mV steps
–45 mV to –155 mV in 5-mV steps
300 mV, 400 mV, 500 mV, 600 mV
0.25 s, 1.00 s, 1.25 s, 4.50 s
Overcharge detection delay time
Over-discharge detection delay time
Discharging overcurrent detection delay time
20 ms, 96 ms, 125 ms, 144 ms
8 ms, 16 ms, 20 ms, 48 ms
14
Submit Documentation Feedback
Copyright © 2014–2020, Texas Instruments Incorporated
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
www.ti.com
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
Overview (continued)
Table 1. Factory Programmable Options (continued)
PARAMETER
FACTORY DEVICE CONFIGURATION
4 ms, 6 ms, 8 ms, 16 ms
250 µs (fixed)
tOCCD
tSCCD
Charging overcurrent detection delay time
Short Circuit detection delay time
For available released devices, see the Released Device Configurations table.
9.2 Functional Block Diagram
Charger
Detection
Circuit
Counter
Oscillator
Logic circuit
Overcharge
Comparator (OVP)
with Hys
BAT 5
2
COUT
Overcharge
Current
Comparator
Delay
Short Detect
Over-Discharge
Comparator (UVP)
with Hys
Logic circuit
3
DOUT
Over-Discharge
Current Comparator
BAT
R
V–D
6 V–
4
VSS
I
V–S
9.3 Feature Description
The BQ2970 family of devices measures voltage drops across several input pins for monitoring and detection of
the following faults: OCC, OCD, OVP, and UVP. An internal oscillator initiates a timer to the fixed delays
associated with each parameter once the fault is triggered. Once the timer expires due to a fault condition, the
appropriate FET drive output (COUT or DOUT) is activated to turn OFF the external FET. The same method is
applicable for the recovery feature once the system fault is removed and the recovery parameter is satisfied, then
the recovery timer is initiated. If there are no reoccurrences of this fault during this period, the appropriate gate
drive is activated to turn ON the appropriate external FET.
9.4 Device Functional Modes
9.4.1 Normal Operation
This device monitors the voltage of the battery connected between BAT pin and VSS pin and the differential
voltage between V– pin and VSS pin to control charging and discharging. The system is operating in NORMAL
mode when the battery voltage range is between the over-discharge detection threshold (VUVP) and the
overcharge detection threshold (VOVP), and the V– pin voltage is within the range for charge overcurrent
threshold (VOCC) to over-discharge current threshold (VOCD) when measured with respect to VSS. If these
conditions are satisfied, the device turns ON the drive for COUT and DOUT FET control.
Copyright © 2014–2020, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
www.ti.com
Device Functional Modes (continued)
CAUTION
When the battery is connected for the first time, the discharging circuit might not be
enabled. In this case, short the V– pin to the VSS pin.
Alternatively, connect the charger between the Pack+ and Pack– terminals in the
system.
9.4.2 Overcharge Status
This mode is detected when the battery voltage measured is higher than the overcharge detection threshold
(VOVP) during charging. If this condition exists for a period greater than the overcharge detection delay (tOVPD) or
longer, the COUT output signal is driven low to turn OFF the charging FET to prevent any further charging of the
battery.
The overcharge condition is released if one of the following conditions occurs:
•
If the V– pin is higher than the overcharge detection voltage (VOCC_Min), the device releases the overcharge
status when the battery voltage drops below the overcharge release voltage (VOVP-Hys).
•
If the V– pin is higher than or equal to the over-discharge detection voltage (VOCD), the device releases the
overcharge status when the battery voltage drops below the overcharge detection voltage (VOVP).
The discharge is initiated by connecting a load after the overcharge detection. The V– pin rises to a voltage
greater than VSS due to the parasitic diode of the charge FET conducting to support the load. If the V– pin
voltage is higher than or equal to the discharge overcurrent detection threshold (VOCD), the overcurrent condition
status is released only if the battery voltage drops lower than or equal to the overcharge detection voltage (VOVP).
CAUTION
1. If the battery is overcharged to a level greater than overcharge detection (VOVP) and the
battery voltage does not drop below the overcharge detection voltage (VOVP) with a heavy
load connected, the discharge overcurrent and load short-circuit detection features do not
function until the battery voltage drops below the overcharge detection voltage (VOVP). The
internal impedance of a battery is in the order of tens of mΩ, so application of a heavy load
on the output should allow the battery voltage to drop immediately, enabling discharge
overcurrent detection and load short-circuit detection features after an overcharge release
delay.
2. When a charger is connected after an overcharge detection, the overcharge status does not
release even if the battery voltage drops below the overcharge release threshold. The
overcharge status is released when the V– pin voltage exceeds the overcurrent detection
voltage (VOCD) by removing the charger.
9.4.3 Over-Discharge Status
If the battery voltage drops below the over-discharge detection voltage (VUVP) for a time greater than (tUVPD) the
discharge control output, DOUT is switched to a low state and the discharge FET is turned OFF to prevent
further discharging of the battery. This is referred to as an over-discharge detection status. In this condition, the
V– pin is internally pulled up to BAT by the resistor RV–D. When this occurs, the voltage difference between V–
and BAT pins is 1.3 V or lower, and the current consumption of the device is reduced to power-down level
ISTANDBY. The current sink IV–S is not active in power-down state or over-discharge state. The power-down state is
released when a charger is connected and the voltage delta between V– and BAT pins is greater than 1.3 V.
If a charger is connected to a battery in over-discharge state and the voltage detected at the V– is lower than
–0.7 V, the device releases the over-discharge state and allows the DOUT pin to go high and turn ON the
discharge FET once the battery voltage exceeds over-discharge detection voltage (VUVP).
If a charger is connected to a battery in over-discharge state and the voltage detected at the V– is higher than
–0.7 V, the device releases the over-discharge state and allows the DOUT pin to go high and turn ON the
discharge FET once the battery voltage exceeds over-discharge detection release hysteresis voltage (VUVP +Hys).
16
Submit Documentation Feedback
Copyright © 2014–2020, Texas Instruments Incorporated
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
www.ti.com
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
Device Functional Modes (continued)
9.4.4 Discharge Overcurrent Status (Discharge Overcurrent, Load Short-Circuit)
When a battery is in normal operation and the V– pin is equal to or higher than the discharge overcurrent
threshold for a time greater than the discharge overcurrent detection delay, the DOUT pin is pulled low to turn
OFF the discharge FET and prevent further discharge of the battery. This is known as the discharge overcurrent
status. In the discharge overcurrent status, the V– and VSS pins are connected by a constant current sink IV–S
.
When this occurs and a load is connected, the V– pin is at BAT potential. If the load is disconnected, the V– pin
goes to VSS (BAT/2) potential.
This device detects the status when the impedance between Pack+ and Pack– (see Figure 26) increases and is
equal to the impedance that enables the voltage at the V– pin to return to BAT – 1 V or lower. The discharge
overcurrent status is restored to the normal status.
Alternatively, by connecting the charger to the system, the device returns to normal status from discharge
overcurrent detection status, because the voltage at the V– pin drops to BAT – 1 V or lower.
The resistance RV–D between V– and BAT is not connected in the discharge overcurrent detection status.
9.4.5 Charge Overcurrent Status
When a battery is in normal operation status and the voltage at V– pin is lower than the charge overcurrent
detection due to high charge current for a time greater than charge overcurrent detection delay, the COUT pin is
pulled low to turn OFF the charge FET and prevent further charging to continue. This is known as charge
overcurrent status.
The device is restored to normal status from charge overcurrent status when the voltage at the V– pin returns to
charge overcurrent detection voltage or higher by removing the charger from the system.
The charge overcurrent detection feature does not work in the over-discharge status.
The resistance RV–D between V– and BAT and the current sink IV–S is not connected in the charge overcurrent
status.
9.4.6 0-V Charging Function Enabled
This feature enables recharging a connected battery that has very low voltage due to self-discharge. When the
charger applies a voltage greater than or equal to V0CHG to Pack+ and Pack– connections, the COUT pin gate
drive is fixed by the BAT pin voltage.
Once the voltage between the gate and the source of the charging FET becomes equal to or greater than the
turn ON voltage due to the charger voltage, the charging FET is ON and the battery is charged with current flow
through the charging FET and the internal parasitic diode of the discharging FET. Once the battery voltage is
equal to or higher than the over-discharge release voltage, the device enters normal status.
CAUTION
1. Some battery providers do not recommend charging a depleted (self-discharged) battery.
Consult the battery supplier to determine whether to have the 0-V battery charger function.
2. The 0-V battery charge feature has a higher priority than the charge overcurrent detection
function. In this case, the 0-V charging will be allowed and the battery charges forcibly,
which results in charge overcurrent detection being disabled if the battery voltage is lower
than the over-discharge detection voltage.
9.4.7 0-V Charging Inhibit Function
This feature inhibits recharging a battery that has an internal short circuit of a 0-V battery. If the battery voltage is
below the charge inhibit voltage V0INH or lower, the charge FET control gate is fixed to the Pack– voltage to
inhibit charging. When the battery is equal to V0INH or higher, charging can be performed. The 0-V charge inhibit
function is available in all configurations of the BQ297xx device.
Copyright © 2014–2020, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
www.ti.com
Device Functional Modes (continued)
CAUTION
Some battery providers do not recommend charging a depleted (self-discharged)
battery. Consult the battery supplier to determine whether to enable or inhibit the 0-V
battery charger function.
9.4.8 Delay Circuit
The detection delay timers are based from an internal clock with a frequency of 10 kHz.
BAT
t
0 ≤ t ≤ t
D
D
SCCD
VSS
Time
tD
t
OCDD
˂
V
SCC
V
OCD
VSS
Time
Figure 25. Delay Circuit
If the over-discharge current is detected, but remains below the over-discharge short circuit detection threshold,
the over-discharge detection conditions must be valid for a time greater than or equal to over-discharge current
delay tOCCD time before the DOUT goes low to turn OFF the discharge FET. However, during any time the
discharge overcurrent detection exceeds the short circuit detection threshold for a time greater than or equal to
load circuit detection delay tSCCD, the DOUT pin goes low in a faster delay for protection.
18
Submit Documentation Feedback
Copyright © 2014–2020, Texas Instruments Incorporated
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
www.ti.com
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
10 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
10.1 Application Information
The BQ2970 devices are a family of primary protectors used for protection of the battery pack in the application.
The application drives two low-side NMOS FETs that are controlled to provide energy to the system loads or
interrupt the power in the event of a fault condition.
10.2 Typical Application
PACK+
V–
NC
330
BAT
VSS
COUT
DOUT
CELLP
CELLN
2.2k
PACK–
D
S
S
CHG
DSG
NOTE: The 5-M resistor for an external gate-source is optional.
Figure 26. Typical Application Schematic, BQ2970
10.2.1 Design Requirements
For this design example, use the parameters listed in Table 2.
Table 2. Design Parameters
DESIGN PARAMETER
Input voltage range
EXAMPLE VALUE at TA = 25°C
4.5 V to 7 V
7 A
Maximum operating discharge current
Maximum Charge Current for battery pack
Overvoltage Protection (OVP)
4.5 A
4.275 V
1.2 s
Overvoltage detection delay timer
Overvoltage Protection (OVP) release voltage
Undervoltage Protection (UVP)
4.175 V
2.8 V
Undervoltage detection delay timer
150 ms
2.9 V
Undervoltage Protection (UVP) release voltage
Charge Overcurrent detection (OCC) voltage
Charge Overcurrent Detection (OCC) delay timer
Discharge Overcurrent Detection (OCD) voltage
Discharge Overcurrent Detection (OCD) delay timer
–70 mV
9 ms
100 mV
18 ms
Copyright © 2014–2020, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
www.ti.com
Typical Application (continued)
Table 2. Design Parameters (continued)
DESIGN PARAMETER
EXAMPLE VALUE at TA = 25°C
Load Short Circuit Detection SCC) voltage, BAT to –V ≤ threshold
Load Short Circuit Detection (SCC) delay timer
500 mV
250 µs
1 V
Load Short Circuit release voltage, BAT to –V ≥ Threshold
10.2.2 Detailed Design Procedure
NOTE
The external FET selection is important to ensure the battery pack protection is sufficient
and complies to the requirements of the system.
•
FET Selection: Because the maximum desired discharge current is 7 A, ensure that the Discharge
Overcurrent circuit does not trigger until the discharge current is above this value.
•
•
The total resistance tolerated across the two external FETs (CHG + DSG) should be 100 mV/7 A = 14.3 mΩ.
Based on the information of the total ON resistance of the two switches, determine what would be the Charge
Overcurrent Detection threshold, 14.3 mΩ × 4.5 A = 65 mV. Selecting a device with a 70-mV trigger threshold
for Charge Overcurrent trigger is acceptable.
•
The total Rds ON should factor in any worst-case parameter based on the FET ON resistance, de-rating due
to temperature effects and minimum required operation, and the associated gate drive (Vgs). Therefore, the
FET choice should meet the following criteria:
Vdss = 25 V
Each FET Rds ON = 7.5 mΩ at Tj = 25°C and Vgs = 3.5 V
•
Imax > 50 A to allow for short Circuit Current condition for 350 µs (max delay timer). The only limiting factor
during this condition is Pack Voltage/(Cell Resistance + (2 × FET_RdsON) + Trace Resistance).
•
•
Use the CSD16406Q3 FET for the application.
An RC filter is required on the BAT for noise, and enables the device to operate during sharp negative
transients. The 330-Ω resistor also limits the current during a reverse connection on the system.
•
TI recommends placing a high impedance 5-MΩ across the gate source of each external FET to deplete any
charge on the gate-source capacitance.
20
Submit Documentation Feedback
Copyright © 2014–2020, Texas Instruments Incorporated
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
www.ti.com
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
10.2.3 Application Performance Plots
Orange Line (Channel 1) = Power Up Ramp on BAT Pin
Turquoise Line (Channel 2) = DOUT Gate Drive Output
Orange Line (Channel 1) = Power Down Ramp on BAT Pin
Turquoise Line (Channel 2) = DOUT Date Drive Output
DOUT goes from low to high when UVP Recovery = UVP Set
Threshold +100 mV
DOUT goes from high to low when UVP threshold = UVP set
Threshold + set delay time
Figure 27. UVP Recovery
Figure 28. UVP Set Condition
Orange Line (Channel 1) = Power Up Ramp on BAT pin
Turquoise Line (Channel 2) = DOUT Gate Drive Output
Orange Line (Channel 1) = Power Up Ramp on BAT Pin
Turquoise Line (Channel 2) = COUT Gate Drive Output
Figure 29. Initial Power Up, DOUT
Figure 30. Initial Power Up, COUT
Orange Line (Channel 1) = Decrease Voltage on BAT Pin
Turquoise Line (Channel 2) = COUT Gate Drive Output
Orange Line (Channel 1) = Power Up Ramp on BAT Pin
Turquoise Line (Channel 2) = COUT Gate Drive Output
COUT goes from low to high when OVP Recovery = OVP Set
Threshold –100 mV
COUT goes from high to low when OVP threshold = OVP set
Threshold + set delay time
Figure 32. OVP Recovery Condition
Figure 31. OVP Set Condition
Copyright © 2014–2020, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
www.ti.com
11 Power Supply Recommendations
The recommended power supply for this device is a maximum 8-V operation on the BAT input pin.
12 Layout
12.1 Layout Guidelines
The following are the recommended layout guidelines:
1. Ensure the external power FETs are adequately compensated for heat dissipation with sufficient thermal
heat spreader based on worst-case power delivery.
2. The connection between the two external power FETs should be very close to ensure there is not an
additional drop for fault sensing.
3. The input RC filter on the BAT pin should be close to the terminal of the IC.
12.2 Layout Example
Power Trace Line
PACK+
V–
BAT
VSS
6
5
4
1
2
NC
COUT
DOUT
–
PACK
3
Power Trace Line
Power Trace Line
CSD16406Q3
CSD16406Q3
Power Trace
Via connects between two layers
Figure 33. BQ2970 Board Layout
22
Submit Documentation Feedback
Copyright © 2014–2020, Texas Instruments Incorporated
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
BQ2970, BQ2971, BQ2972, BQ2973
www.ti.com
SLUSBU9G –MARCH 2014–REVISED JANUARY 2020
13 Device and Documentation Support
13.1 Related Documentation
BQ29700 Single-Cell Li-Ion Protector EVM User's Guide (SLUUAZ3)
13.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 3. Related Links
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
PARTS
PRODUCT FOLDER
SAMPLE & BUY
BQ2970
BQ2971
BQ2972
BQ2973
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
13.3 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
13.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
13.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
13.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
14 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2014–2020, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: BQ2970 BQ2971 BQ2972 BQ2973
PACKAGE OPTION ADDENDUM
www.ti.com
11-Nov-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
Qty
3000
250
(1)
(2)
(3)
(4/5)
(6)
BQ29700DSER
BQ29700DSET
BQ29701DSER
BQ29701DSET
BQ29702DSER
BQ29702DSET
BQ29703DSER
BQ29703DSET
BQ29704DSER
BQ29704DSET
BQ29705DSER
BQ29705DSET
BQ29706DSER
BQ29706DSET
BQ29707DSER
BQ29707DSET
ACTIVE
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
Green (RoHS
& no Sb/Br)
NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
FA
FA
FY
FY
FZ
FZ
F1
F1
F2
F2
F3
F3
F4
F4
F5
F5
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Green (RoHS
& no Sb/Br)
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
11-Nov-2020
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
Qty
3000
250
(1)
(2)
(3)
(4/5)
(6)
BQ29716DSER
BQ29716DSET
BQ29717DSER
BQ29717DSET
BQ29718DSER
BQ29718DSET
BQ29723DSER
BQ29723DSET
BQ29729DSER
BQ29729DSET
BQ29732DSER
BQ29732DSET
BQ29733DSER
BQ29733DSET
BQ29739DSER
ACTIVE
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
Green (RoHS
& no Sb/Br)
NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
3P
3P
3Q
3Q
3R
3R
3S
3S
3T
3T
3U
3U
4Q
4Q
KB
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
PREVIEW
Green (RoHS
& no Sb/Br)
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
11-Nov-2020
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Dec-2019
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
BQ29700DSER
BQ29700DSET
BQ29701DSER
BQ29701DSET
BQ29702DSER
BQ29702DSET
BQ29703DSER
BQ29703DSET
BQ29704DSER
BQ29704DSET
BQ29705DSER
BQ29705DSET
BQ29706DSER
BQ29706DSET
BQ29707DSER
BQ29707DSET
BQ29716DSER
BQ29716DSET
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
3000
250
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
3000
250
3000
250
3000
250
3000
250
3000
250
3000
250
3000
250
3000
250
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Dec-2019
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
BQ29717DSER
BQ29717DSET
BQ29718DSER
BQ29718DSET
BQ29723DSER
BQ29723DSET
BQ29729DSER
BQ29729DSET
BQ29732DSER
BQ29732DSET
BQ29733DSER
BQ29733DSET
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
6
6
6
6
6
6
6
6
6
6
6
6
3000
250
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
3000
250
3000
250
3000
250
3000
250
3000
250
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
BQ29700DSER
BQ29700DSET
BQ29701DSER
BQ29701DSET
BQ29702DSER
WSON
WSON
WSON
WSON
WSON
DSE
DSE
DSE
DSE
DSE
6
6
6
6
6
3000
250
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
20.0
20.0
20.0
20.0
20.0
3000
250
3000
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Dec-2019
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
BQ29702DSET
BQ29703DSER
BQ29703DSET
BQ29704DSER
BQ29704DSET
BQ29705DSER
BQ29705DSET
BQ29706DSER
BQ29706DSET
BQ29707DSER
BQ29707DSET
BQ29716DSER
BQ29716DSET
BQ29717DSER
BQ29717DSET
BQ29718DSER
BQ29718DSET
BQ29723DSER
BQ29723DSET
BQ29729DSER
BQ29729DSET
BQ29732DSER
BQ29732DSET
BQ29733DSER
BQ29733DSET
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
250
3000
250
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
3000
250
3000
250
3000
250
3000
250
3000
250
3000
250
3000
250
3000
250
3000
250
3000
250
3000
250
Pack Materials-Page 3
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated
相关型号:
BQ29701
BQ297xx Cost-Effective Voltage and Current Protection Integrated Circuit for Single-Cell Li-Ion and Li-Polymer Batteries
TI
BQ29702
BQ297xx Cost-Effective Voltage and Current Protection Integrated Circuit for Single-Cell Li-Ion and Li-Polymer Batteries
TI
BQ29703
BQ297xx Cost-Effective Voltage and Current Protection Integrated Circuit for Single-Cell Li-Ion and Li-Polymer Batteries
TI
BQ29704
BQ297xx Cost-Effective Voltage and Current Protection Integrated Circuit for Single-Cell Li-Ion and Li-Polymer Batteries
TI
©2020 ICPDF网 联系我们和版权申明