AMC1411-Q1 [TI]
具有高 CMTI 的汽车类 2V 输入、精密电压检测增强型隔离式放大器;型号: | AMC1411-Q1 |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有高 CMTI 的汽车类 2V 输入、精密电压检测增强型隔离式放大器 放大器 |
文件: | 总35页 (文件大小:1950K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
AMC1411-Q1
SBASAB3 – OCTOBER 2021
AMC1411-Q1 Automotive, High-Impedance, 2-V Input, Reinforced Isolated Amplifier
in a 15-mm Stretched SOIC Package
1 Features
3 Description
•
AEC-Q100 qualified for automotive applications:
– Temperature grade 1: –40°C to +125°C, TA
Functional Safety-Capable
– Documentation available to aid functional safety
system design
2-V, high-impedance input voltage range optimized
for isolated voltage measurements
Fixed gain: 1.0 V/V
Low DC errors:
– Offset error ±1.5 mV (max)
– Offset drift: ±10 μV/°C (max)
– Gain error: ±0.2% (max)
The AMC1411-Q1 is a precision, isolated amplifier
with an output separated from the input circuitry by
a capacitive isolation barrier that is highly resistant
to magnetic interference. This barrier is certified
to provide reinforced galvanic isolation of up to
7.5 kVRMS according to VDE V 0884-11 and UL1577
•
•
and supports a working voltage of up to 1600 VRMS
.
•
•
The isolation barrier separates parts of the system
that operate on different common-mode voltage levels
and protects the low-voltage side from voltages that
can cause electrical damage or be harmful to an
operator.
– Gain drift: ±30 ppm/°C (max)
– Nonlinearity 0.04% (max)
3.3-V or 5-V operation on high-side and low-side
Missing high-side supply detection feature
High CMTI: 100 kV/μs (min)
≥15.7-mm creepage, stretched SOIC package
Reinforced isolation:
– 10600-VPK reinforced isolation per DIN VDE V
0884-11: 2017-01
The high-impedance input of the AMC1411-Q1
is optimized for connection to high-impedance
resistive dividers or other high-impedance voltage
signal source. The excellent DC accuracy and
low temperature drift support accurate, isolated
voltage sensing in onboard chargers (OBC), DC/DC
converters, traction inverters, or other applications
that must operate at high common-mode voltages,
high altitudes, or in environments with high pollution
degrees.
•
•
•
•
•
– 7500-VRMS isolation for 1 minute per UL1577
2 Applications
The AMC1411-Q1 is offered in a stretched 8-pin SOIC
package and is AEC-Q100 qualified for automotive
applications and supports the temperature range from
–40°C to +125°C.
•
Isolated voltage sensing in:
– Traction inverters
– Onboard chargers
– DC/DC converters
– HEV/EV DC chargers
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
AMC1411-Q1
SOIC (8)
6.4 mm × 14.0 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
VDC
High-side supply
(3.3 V or 5 V)
Low-side supply
(3.3 V or 5 V)
R1
R2
AMC1411-Q1
VDD1
VDD2
OUTP
IN
SHTDN
GND1
0..2V
RSNS
VCMout
2 V
ADC
OUTN
GND2
Typical Application
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
Table of Contents
1 Features............................................................................1
2 Applications.....................................................................1
3 Description.......................................................................1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
6 Specifications.................................................................. 4
6.1 Absolute Maximum Ratings ....................................... 4
6.2 ESD Ratings .............................................................. 4
6.3 Recommended Operating Conditions ........................4
6.4 Thermal Information ...................................................5
6.5 Power Ratings ............................................................5
6.6 Insulation Specifications ............................................ 6
6.7 Safety-Related Certifications ..................................... 7
6.8 Safety Limiting Values ................................................7
6.9 Electrical Characteristics ............................................8
6.10 Switching Characteristics .......................................10
6.11 Timing Diagram.......................................................10
6.12 Insulation Characteristics Curves............................11
6.13 Typical Characteristics............................................12
7 Detailed Description......................................................18
7.1 Overview...................................................................18
7.2 Functional Block Diagram.........................................18
7.3 Feature Description...................................................18
7.4 Device Functional Modes..........................................20
8 Application and Implementation..................................21
8.1 Application Information............................................. 21
8.2 Typical Application.................................................... 21
8.3 What To Do and What Not To Do..............................25
9 Power Supply Recommendations................................25
10 Layout...........................................................................26
10.1 Layout Guidelines................................................... 26
10.2 Layout Example...................................................... 26
11 Device and Documentation Support..........................27
11.1 Documentation Support.......................................... 27
11.2 Receiving Notification of Documentation Updates..27
11.3 Support Resources................................................. 27
11.4 Trademarks............................................................. 27
11.5 Electrostatic Discharge Caution..............................27
11.6 Glossary..................................................................27
12 Mechanical, Packaging, and Orderable
Information.................................................................... 27
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
DATE
REVISION
NOTES
October 2021
*
Initial Release
Copyright © 2021 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
5 Pin Configuration and Functions
VDD1
IN
1
2
3
4
8
7
6
5
VDD2
OUTP
OUTN
GND2
SHTDN
GND1
Not to scale
Figure 5-1. DWL Package, 8-Pin SOIC (Top View)
Table 5-1. Pin Functions
PIN
NAME
TYPE
DESCRIPTION
NO.
1
2
3
4
5
6
7
8
VDD1
INP
High-side power
Analog input
High-side power supply(1)
Analog input
SHTDN
GND1
GND2
OUTN
OUTP
VDD2
Digital input
Shutdown input, active high, with internal pullup resistor (typical value: 100 kΩ)
High-side analog ground
High-side ground
Low-side ground
Analog output
Analog output
Low-side power
Low-side analog ground
Inverting analog output
Noninverting analog output
Low-side power supply(1)
(1) See the Power Supply Recommendations section for power-supply decoupling recommendations.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
see(1)
MIN
–0.3
MAX
UNIT
High-side VDD1 to GND1
6.5
6.5
Power-supply voltage
Input voltage
V
Low-side VDD2 to GND2
–0.3
IN
GND1 – 6
GND1 – 0.5
GND2 – 0.5
–10
VDD1 + 0.5
VDD1 + 0.5
VDD2 + 0.5
10
V
SHTDN
Output voltage
Input current
OUTP, OUTN
V
Continuous, any pin except power-supply pins
mA
Junction, TJ
Storage, Tstg
150
Temperature
°C
–65
150
(1) Operation outside the Absolute Maximum Ratings may cause permanent device damage. Absolute Maximum Ratings do not imply
functional operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions.
If used outside the Recommended Operating Conditions but within the Absolute Maximum Ratings, the device may not be fully
functional, and this may affect device reliability, functionality, performance, and shorten the device lifetime.
6.2 ESD Ratings
VALUE
±2000
±1000
UNIT
Human-body model (HBM), per AEC Q100-002(1), HBM ESD classification Level 2
Charged-device model (CDM), per AEC Q100-011, CDM ESD classification Level C6
V(ESD)
Electrostatic discharge
V
(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
6.3 Recommended Operating Conditions
over operating ambient temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
POWER SUPPLY
High-side power supply
Low-side power supply
ANALOG INPUT
VDD1 to GND1
VDD2 to GND2
3
3
5
5.5
5.5
V
V
3.3
VClipping
VFSR
Input voltage before clipping output
Specified linear full-scale voltage
IN to GND1
IN to GND1
2.516
V
V
–0.1
0
2
VDD1
125
DIGITAL INPUT
Input voltage
TEMPERATURE RANGE
TA Specified ambient temperature
SHTDN to GND1
V
–40
°C
Copyright © 2021 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
6.4 Thermal Information
AMC1411-Q1
THERMAL METRIC(1)
DWL (SOIC)
8 PINS
63.2
UNIT
RθJA
Junction-to-ambient thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top) Junction-to-case (top) thermal resistance
26.1
RθJB
ψJT
Junction-to-board thermal resistance
28.5
Junction-to-top characterization parameter
Junction-to-board characterization parameter
7.8
ψJB
26.8
RθJC(bot) Junction-to-case (bottom) thermal resistance
n/a
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.5 Power Ratings
PARAMETER
TEST CONDITIONS
VDD1 = VDD2 = 3.6 V
VALUE
56
UNIT
PD
Maximum power dissipation (both sides)
mW
VDD1 = VDD2 = 5.5 V
VDD1 = 3.6 V
98
30
PD1
Maximum power dissipation (high-side)
Maximum power dissipation (low-side)
mW
mW
VDD1 = 5.5 V
53
VDD2 = 3.6 V
26
PD2
VDD2 = 5.5 V
45
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: AMC1411-Q1
AMC1411-Q1
www.ti.com
UNIT
SBASAB3 – OCTOBER 2021
6.6 Insulation Specifications
over operating ambient temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VALUE
GENERAL
CLR
External clearance(1)
External creepage(1)
Distance through insulation
Comparative tracking index
Material group
Shortest pin-to-pin distance through air
Shortest pin-to-pin distance across the package surface
Minimum internal gap (internal clearance) of the double insulation
DIN EN 60112 (VDE 0303-11); IEC 60112
According to IEC 60664-1
≥ 14.7
≥ 15.7
≥ 0.021
≥ 600
I
mm
mm
mm
V
CPG
DTI
CTI
Rated mains voltage ≤ 600 VRMS
I-IV
Overvoltage category
per IEC 60664-1
Rated mains voltage ≤ 1000 VRMS
I-III
DIN VDE V 0884-11 (VDE V 0884-11): 2017-01
Maximum repetitive peak isolation
voltage
VIORM
At AC voltage
2260
VPK
At AC voltage (sine wave)
1600
2260
VRMS
VDC
Maximum-rated isolation
working voltage
VIOWM
At DC voltage
VTEST = VIOTM, t = 60 s (qualification test)
VTEST = 1.2 × VIOTM, t = 1 s (100% production test)
10600
12720
Maximum transient
VIOTM
VPK
VPK
isolation voltage
Maximum surge
VIOSM
Test method per IEC 60065, 1.2/50-µs waveform,
VTEST = 1.6 × VIOSM = 12800 VPK (qualification)
8000
≤ 5
isolation voltage(2)
Method a, after input/output safety test subgroups 2 and 3,
Vini = VIOTM, tini = 60 s, Vpd(m) = 1.2 × VIORM, tm = 10 s
Method a, after environmental tests subgroup 1,
Vini = VIOTM, tini = 60 s, Vpd(m) = 1.6 × VIORM, tm = 10 s
qpd
Apparent charge(3)
≤ 5
pC
Method b1, at routine test (100% production) and preconditioning (type
test), Vini = VIOTM, tini = 1 s, Vpd(m) = 1.875 × VIORM, tm = 1 s
≤ 5
Barrier capacitance,
input to output(4)
CIO
VIO = 0.5 VPP at 1 MHz
~1.5
pF
Ω
VIO = 500 V at TA = 25°C
> 1012
> 1011
> 109
Insulation resistance,
input to output(4)
RIO
VIO = 500 V at 100°C ≤ TA ≤ 125°C
VIO = 500 V at TS = 150°C
Pollution degree
Climatic category
2
55/125/21
UL1577
VTEST = VISO = 7500 VRMS or 10600 VDC, t = 60 s (qualification),
VTEST = 1.2 × VISO = 9000 VRMS, t = 1 s (100% production test)
VISO
Withstand isolation voltage
7500
VRMS
(1) Apply creepage and clearance requirements according to the specific equipment isolation standards of an application. Care must be
taken to maintain the creepage and clearance distance of a board design to ensure that the mounting pads of the isolator on the
printed circuit board (PCB) do not reduce this distance. Creepage and clearance on a PCB become equal in certain cases. Techniques
such as inserting grooves, ribs, or both on a PCB are used to help increase these specifications.
(2) Testing is carried out in air or oil to determine the intrinsic surge immunity of the isolation barrier.
(3) Apparent charge is electrical discharge caused by a partial discharge (pd).
(4) All pins on each side of the barrier are tied together, creating a two-pin device.
Copyright © 2021 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
6.7 Safety-Related Certifications
VDE
UL
Certified according to DIN VDE V 0884-11 (VDE V 0884-11): 2017-01,
DIN EN 60950-1 (VDE 0805 Teil 1): 2014-08, and
DIN EN 60065 (VDE 0860): 2005-11
Recognized under 1577 component recognition and
CSA component acceptance NO 5 programs
Reinforced insulation
Single protection
Certificate number: pending
File number: E181974
6.8 Safety Limiting Values
Safety limiting(1) intends to minimize potential damage to the isolation barrier upon failure of input or output circuitry. A
failure of the I/O can allow low resistance to ground or the supply and, without current limiting, dissipate sufficient power to
over-heat the die and damage the isolation barrier potentially leading to secondary system failures.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
RθJA = 63.2°C/W, VDDx = 3.6 V,
TJ = 150°C, TA = 25°C
550
IS
Safety input, output, or supply current
mA
RθJA = 63.2°C/W, VDDx = 5.5 V,
TJ = 150°C, TA = 25°C
360
PS
TS
Safety input, output, or total power
Maximum safety temperature
RθJA = 63.2°C/W, TJ = 150°C, TA = 25°C
1980
150
mW
°C
(1) The maximum safety temperature, TS, has the same value as the maximum junction temperature, TJ, specified for the device. The IS
and PS parameters represent the safety current and safety power, respectively. Do not exceed the maximum limits of IS and PS. These
limits vary with the ambient temperature, TA.
The junction-to-air thermal resistance, RθJA, in the Thermal Information table is that of a device installed on a high-K test board for
leaded surface-mount packages. Use these equations to calculate the value for each parameter:
TJ = TA + RθJA × P, where P is the power dissipated in the device.
TJ(max) = TS = TA + RθJA × PS, where TJ(max) is the maximum junction temperature.
PS = IS × VDDmax, where VDDmax is the maximum supply voltage for high-side and low-side.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
6.9 Electrical Characteristics
minimum and maximum specifications apply from TA = –40°C to +125°C, VDD1 = 3.0 V to 5.5 V, VDD2 = 3.0 V to 5.5 V, VIN
= –0.1 V to 2 V, and SHTDN = GND1 = 0 V (unless otherwise noted); typical specifications are at TA = 25°C, VDD1 = 5 V,
and VDD2 = 3.3 V
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
ANALOG INPUT
VOS
TCVOS
RIN
Input offset voltage
Input offset thermal drift(1) (2) (4)
Input resistance
TA = 25°C(1) (2)
–1.5
–10
±0.1
±3
1
1.5
mV
10 µV/°C
GΩ
TA = 25℃
IIB
Input bias current
IN = GND1, TA = 25℃
fIN = 275 kHz
–15
3.5
7
15
nA
pF
CIN
Input capacitance
ANALOG OUTPUT
Nominal gain
1
±0.05
±5
V/V
%
EG
Gain error(1)
TA = 25℃
–0.2
–30
0.2
TCEG
Gain error drift(1) (5)
Nonlineartity(1)
30 ppm/°C
0.04%
–0.04%
±0.01%
VIN = 2 VPP, VIN > 0 V,
fIN = 10 kHz, BW = 10 kHz
THD
SNR
Total harmonic distortion(3)
–87
dB
VIN = 2 VPP, fIN = 1 kHz, BW = 10 kHz
VIN = 2 VPP, fIN = 10 kHz, BW = 100 kHz
VIN = GND1, BW = 100 kHz
vs VDD1, at DC
79
82.6
70.9
220
–80
–85
–65
–70
1.44
Signal-to-noise ratio
Output noise
dB
µVrms
vs VDD2, at DC
PSRR
Power-supply rejection ratio(2)
dB
vs VDD1, 10 kHz / 100-mV ripple
vs VDD2, 10 kHz / 100-mV ripple
VCMout
Output common-mode voltage
1.39
220
1.49
–2.5
V
V
VOUT = (VOUTP – VOUTN);
VIN > VClipping
VCLIPout
Clipping differential output voltage
2.49
–2.6
SHTDN = high, or VDD1 undervoltage,
or VDD1 missing
VFAILSAFE Failsafe differential output voltage
V
BW
Output bandwidth
Output resistance
275
kHz
Ω
ROUT
On OUTP or OUTN
<0.2
On OUTP or OUTN, sourcing or sinking,
IN = GND1, outputs shorted to
either GND or VDD2
Output short-circuit current
14
mA
CMTI
Common-mode transient immunity
100
–70
150
kV/µs
DIGITAL INPUT
IIN
Input current
SHTDN pin, GND1 ≤ SHTDN ≤ VDD1
SHTDN pin
1
µA
pF
CIN
Input capacitance
5
0.7 ×
VDD1
VIH
VIL
High-level input voltage
V
V
0.3 ×
VDD1
Low-level input voltage
Copyright © 2021 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
6.9 Electrical Characteristics (continued)
minimum and maximum specifications apply from TA = –40°C to +125°C, VDD1 = 3.0 V to 5.5 V, VDD2 = 3.0 V to 5.5 V, VIN
= –0.1 V to 2 V, and SHTDN = GND1 = 0 V (unless otherwise noted); typical specifications are at TA = 25°C, VDD1 = 5 V,
and VDD2 = 3.3 V
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
POWER SUPPLY
VDD1 rising
2.5
2.4
2.7
2.6
2.45
2.0
6.0
7.1
1.3
5.3
5.9
2.9
V
VDD1 undervoltage detection
threshold
VDD1UV
VDD2UV
VDD1 falling
2.8
VDD2 rising
2.2
2.65
V
2.2
VDD2 undervoltage detection
threshold
VDD2 falling
1.85
3.0 V < VDD1 < 3.6 V
4.5 V < VDD1 < 5.5 V, SHTDN = low
SHTDN = VDD1
8.4
mA
9.7
IDD1
High-side supply current
Low-side supply current
µA
3.0 V < VDD2 < 3.6 V
4.5 V < VDD2 < 5.5 V
7.2
mA
8.1
IDD2
(1) The typical value includes one standard deviation (sigma) at nominal operating conditions.
(2) This parameter is input referred.
(3) THD is the ratio of the rms sum of the amplitudes of first five higher harmonics to the amplitude of the fundamental.
(4) Offset error temperature drift is calculated using the box method, as described by the following equation:
TCVOS = (ValueMAX - ValueMIN) / TempRange
(5) Gain error temperature drift is calculated using the box method, as described by the following equation:
TCEG (ppm) = (ValueMAX - ValueMIN) / (Value(T=25℃) x TempRange) x 106
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
6.10 Switching Characteristics
over operating ambient temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
1.3
1.3
1
MAX
UNIT
µs
tr
tf
Output signal rise time
Output signal fall time
µs
IN to OUTx signal delay (50% – 10%)
IN to OUTx signal delay (50% – 50%)
IN to OUTx signal delay (50% – 90%)
Unfiltered output
Unfiltered output
Unfiltered output
1.5
2.1
3
µs
1.6
2.5
µs
µs
VDD1 step to 3.0 V with VDD2 ≥ 3.0 V, to
VOUTP, VOUTN valid, 0.1% settling
tAS
Analog settling time
50
100
µs
tEN
Device enable time
SHTDN high to low
SHTDN low to high
50
3
100
10
µs
µs
tSHTDN
Device shutdown time
6.11 Timing Diagram
2 V
IN
0 V
tf
tr
OUTN
OUTP
VCMout
50% - 10%
50% - 50%
50% - 90%
Figure 6-1. Rise, Fall, and Delay Time Definition
Copyright © 2021 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
6.12 Insulation Characteristics Curves
600
2250
2000
1750
1500
1250
1000
750
VDD1 = VDD2 = 3.6 V
VDD1 = VDD2 = 5.5 V
500
400
300
200
100
0
500
250
0
0
25
50
75
TA (°C)
100
125
150
0
25
50
75
TA (°C)
100
125
150
Figure 6-3. Thermal Derating Curve for Safety-Limiting Power
per VDE
Figure 6-2. Thermal Derating Curve for Safety-Limiting Current
per VDE
TA up to 150°C, stress-voltage frequency = 60 Hz, isolation working voltage = 1600 VRMS, projected insulation lifetime = 98 years
Figure 6-4. Reinforced Isolation Capacitor Lifetime Projection
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
6.13 Typical Characteristics
at VDD1 = 5 V, VDD2 = 3.3 V, SHTDN = 0 V, fIN = 10 kHz, and BW = 100 kHz (unless otherwise noted)
1.5
1
0.5
0
-0.5
-1
Device 1
Device 2
Device 3
-1.5
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
VDD1 = 5 V
Figure 6-6. Input Offset Voltage vs Temperature
Figure 6-5. Input Offset Voltage vs Supply Voltage
2.5
15
Device 1
Device 2
Device 3
2
1.5
1
12
9
6
0.5
0
3
0
-0.5
-1
-3
-6
-9
-12
-15
-1.5
-2
-2.5
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
3
3.5
4
4.5
VDD1 (V)
5
5.5
VDD1 = 3.3 V
Figure 6-7. Input Offset Voltage vs Temperature
Figure 6-8. Input Bias Current vs High-Side Supply Voltage
15
14
12
9
12
10
8
6
3
0
6
-3
-6
-9
-12
-15
4
2
0
100
1000
fIN (kHz)
10000
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
Figure 6-10. Input Capacitance vs Input Signal Frequency
Figure 6-9. Input Bias Current vs Temperature
Copyright © 2021 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
6.13 Typical Characteristics (continued)
at VDD1 = 5 V, VDD2 = 3.3 V, SHTDN = 0 V, fIN = 10 kHz, and BW = 100 kHz (unless otherwise noted)
5
4.5
4
5
0
OUTP
OUTN
-5
3.5
3
-10
-15
-20
-25
-30
-35
-40
2.5
2
1.5
1
0.5
0
1
10
100
1000
-0.1
0.3
0.7
1.1
VIN (V)
1.5
1.9
2.3
2.7
fIN (kHz)
Figure 6-12. Normalized Gain vs Input Frequency
Figure 6-11. Output Voltage vs Input Voltage
0.2
0.15
0.1
0°
-45°
-90°
-135°
-180°
-225°
-270°
-315°
-360°
0.05
0
-0.05
-0.1
-0.15
-0.2
VDD1
VDD2
3
3.5
4
4.5
VDDx (V)
5
5.5
1
10
100
1000
fIN (kHz)
Figure 6-14. Gain Error vs Supply Voltage
Figure 6-13. Output Phase vs Input Frequency
0.2
0.15
0.1
Device 1
Device 2
Device 3
0.05
0
-0.05
-0.1
-0.15
-0.2
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
Figure 6-15. Gain Error vs Temperature
Figure 6-16. Nonlinearity vs Input Voltage
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
6.13 Typical Characteristics (continued)
at VDD1 = 5 V, VDD2 = 3.3 V, SHTDN = 0 V, fIN = 10 kHz, and BW = 100 kHz (unless otherwise noted)
0.04
0.03
0.02
0.01
0
0.04
0.03
0.02
0.01
0
vs VDD1
vs VDD2
-0.01
-0.02
-0.03
-0.04
-0.01
-0.02
-0.03
-0.04
Device 1
Device 2
Device 3
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
3
3.5
4
4.5
VDDx (V)
5
5.5
Figure 6-18. Nonlinearity vs Temperature
Figure 6-17. Nonlinearity vs Supply Voltage
-70
-70
-75
VDD1
VDD2
-75
-80
-80
-85
-85
-90
-90
Device 1
Device 2
Device 3
-95
-95
-100
-100
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
3
3.5
4
4.5
VDDx (V)
5
5.5
Figure 6-20. Total Harmonic Distortion vs Temperature
Figure 6-19. Total Harmonic Distortion vs Supply Voltage
80
72.5
70
VDD1
VDD2
77.5
75
67.5
65
62.5
60
72.5
70
57.5
55
67.5
65
52.5
50
62.5
60
47.5
45
3
3.5
4
4.5
VDDx (V)
5
5.5
42.5
0
0.2 0.4 0.6 0.8
1
1.2 1.4 1.6 1.8
2
VIN (V)
Figure 6-21. Signal-to-Noise Ratio vs Input Voltage
Figure 6-22. Signal-to-Noise Ratio vs Supply Voltage
Copyright © 2021 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
6.13 Typical Characteristics (continued)
at VDD1 = 5 V, VDD2 = 3.3 V, SHTDN = 0 V, fIN = 10 kHz, and BW = 100 kHz (unless otherwise noted)
1000
100
10
80
77.5
75
72.5
70
67.5
65
1
Device 1
Device 2
Device 3
62.5
60
0.1
0.1
1
10
100
1000
Frequency (kHz)
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
Figure 6-24. Input-Referred Noise Density vs Frequency
Figure 6-23. Signal-to-Noise Ratio vs Temperature
0
1.49
1.48
1.47
1.46
1.45
1.44
1.43
1.42
1.41
1.4
-20
-40
-60
-80
-100
VDD1
VDD2
-120
0.1
1.39
1
10
100
1000
3
3.5
4
4.5
VDD2 (V)
5
5.5
Ripple Frequency (kHz)
100-mV ripple
Figure 6-25. Power-Supply Rejection Ratio vs Ripple Frequency
Figure 6-26. Output Common-Mode Voltage vs Low-Side Supply
Voltage
1.49
1.48
1.47
1.46
1.45
1.44
1.43
1.42
1.41
1.4
300
290
280
270
260
250
240
230
220
210
200
1.39
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
3
3.5
4
4.5
VDD2 (V)
5
5.5
Figure 6-27. Output Common-Mode Voltage vs Temperature
Figure 6-28. Output Bandwidth vs Low-Side Supply Voltage
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
6.13 Typical Characteristics (continued)
at VDD1 = 5 V, VDD2 = 3.3 V, SHTDN = 0 V, fIN = 10 kHz, and BW = 100 kHz (unless otherwise noted)
300
290
280
270
260
250
240
230
220
210
200
8.5
8
7.5
7
6.5
6
5.5
5
4.5
4
IDD1 vs VDD1
IDD2 vs VDD2
3.5
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
3
3.5
4
4.5
VDDx (V)
5
5.5
Figure 6-29. Output Bandwidth vs Temperature
Figure 6-30. Supply Current vs Supply Voltage
4
3.5
3
8.5
8
7.5
7
2.5
2
6.5
6
1.5
1
5.5
5
4.5
4
0.5
0
IDD1
IDD2
3
3.5
4
4.5
VDD2 (V)
5
5.5
3.5
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
Figure 6-31. Supply Current vs Temperature
Figure 6-32. Output Rise and Fall Time vs Low-Side Supply
Voltage
3.8
50% - 90%
50% - 50%
50% - 10%
3.4
3
2.6
2.2
1.8
1.4
1
0.6
0.2
3
3.5
4
4.5
VDD2 (V)
5
5.5
Figure 6-33. Output Rise and Fall Time vs Temperature
Figure 6-34. IN to OUTP, OUTN Signal Delay vs Low-Side
Supply Voltage
Copyright © 2021 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
6.13 Typical Characteristics (continued)
at VDD1 = 5 V, VDD2 = 3.3 V, SHTDN = 0 V, fIN = 10 kHz, and BW = 100 kHz (unless otherwise noted)
3.8
50% - 90%
50% - 50%
50% - 10%
3.4
3
2.6
2.2
1.8
1.4
1
0.6
0.2
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
Figure 6-35. IN to OUTP, OUTN Signal Delay vs Temperature
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
7 Detailed Description
7.1 Overview
The AMC1411-Q1 is a precision, single-ended input, isolated amplifier with a high input-impedance and wide
input voltage range. The input stage of the device drives a second-order, delta-sigma (ΔΣ) modulator. The
modulator converts the analog input signal into a digital bitstream that is transferred across the isolation barrier
and separates the high-side from the low-side. On the low-side, the received bitstream is processed by a
fourth-order analog filter that outputs a differential signal at the OUTP and OUTN pins proportional to the input
signal.
The SiO2-based, capacitive isolation barrier supports a high level of magnetic field immunity, as described
in the ISO72x Digital Isolator Magnetic-Field Immunity application report. The digital modulation used in the
AMC1411-Q1 to transmit data across the isolation barrier, and the isolation barrier characteristics itself, result in
high reliability and common-mode transient immunity.
7.2 Functional Block Diagram
VDD1
VDD2
OUTP
OUTN
GND2
AMC1411-Q1
Analog Filter
IN
ΔΣ Modulator
SHTDN
GND1
7.3 Feature Description
7.3.1 Analog Input
The single-ended, high-impedance input stage of the AMC1411-Q1 feeds a second-order, switched-capacitor,
feed-forward ΔΣ modulator. The modulator converts the analog signal into a bitstream that is transferred across
the isolation barrier, as described in the Isolation Channel Signal Transmission section.
There are two restrictions on the analog input signal IN. First, if the input voltage VIN exceeds the range
specified in the Absolute Maximum Ratings table, the input current must be limited to the absolute maximum
value, because the electrostatic discharge (ESD) protection turns on. In addition, the linearity and parametric
performance of the device is ensured only when the analog input voltage remains within the linear full-scale
range (VFSR) as specified in the Recommended Operating Conditions table.
Copyright © 2021 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
7.3.2 Isolation Channel Signal Transmission
The AMC1411-Q1 uses an on-off keying (OOK) modulation scheme, as shown in Figure 7-1, to transmit the
modulator output bitstream across the SiO2-based isolation barrier. The transmit driver (TX) shown in the
Functional Block Diagram transmits an internally-generated, high-frequency carrier across the isolation barrier
to represent a digital one and does not send a signal to represent a digital zero. The nominal frequency of the
carrier used inside the AMC1411-Q1 is 480 MHz.
The receiver (RX) on the other side of the isolation barrier recovers and demodulates the signal and provides
the input to the fourth-order analog filter. The AMC1411-Q1 transmission channel is optimized to achieve the
highest level of common-mode transient immunity (CMTI) and lowest level of radiated emissions caused by the
high-frequency carrier and RX/TX buffer switching.
Internal Clock
Modulator Bitstream
on High-side
Signal Across Isolation Barrier
Recovered Sigal
on Low-side
Figure 7-1. OOK-Based Modulation Scheme
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
7.3.3 Analog Output
The AMC1411-Q1 provides a differential analog output on the OUTP and OUTN pins. For input voltages VIN in
the range from –0.1 V to +2 V, the device provides a linear response with a nominal gain of 1. For example, for
an input voltage of 2 V, the differential output voltage (VOUTP – VOUTN) is 2 V. At zero input (IN shorted to GND1),
both pins output the same common-mode output voltage VCMout, as specified in the Electrical Characteristics
table. For input voltages greater than 2 V but less than approximately 2.5 V, the differential output voltage
continues to increase but with reduced linearity performance. The outputs saturate at a differential output voltage
of VCLIPout, as shown in Figure 7-2, if the input voltage exceeds the VClipping value.
Maximum input range before clipping (VClipping
)
Linear input range (VFSR
)
VFAILSAFE
VOUTN
VCLIPout
VOUTP
VCMout
0
2.516 V
Input Voltage (VIN
)
2 V
Figure 7-2. Output Behavior of the AMC1411-Q1
The AMC1411-Q1 output offers a fail-safe feature that simplifies diagnostics on system level. Figure 7-2 shows
the fail-safe mode, in which the AMC1411-Q1 outputs a negative differential output voltage that does not occur
under normal operating conditions. The fail-safe output is active in three cases:
•
•
•
When the high-side supply VDD1 of the AMC1411-Q1 device is missing
When the high-side supply VDD1 falls below the undervoltage threshold VDD1UV
When the SHTDN pin is pulled high
Use the maximum VFAILSAFE voltage specified in the Electrical Characteristics table as a reference value for
fail-safe detection on a system level.
7.4 Device Functional Modes
The AMC1411-Q1 is operational when the power supplies VDD1 and VDD2 are applied as specified in the
Recommended Operating Conditions table.
Copyright © 2021 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
8 Application and Implementation
Note
Information in the following applications sections is not part of the TI component specification,
and TI does not warrant its accuracy or completeness. TI’s customers are responsible for
determining suitability of components for their purposes, as well as validating and testing their design
implementation to confirm system functionality.
8.1 Application Information
The high input impedance, low input bias current, excellent accuracy, and low temperature drift make the
AMC1411-Q1 a high-performance solution for automotive applications where voltage sensing in the presence of
high common-mode voltage levels is required.
8.2 Typical Application
Reinforced isolated amplifiers are commonly offered in SOIC packages with less than 9 mm of clearance
and creepage specification. Automotive systems supporting working voltages greater than 850 V, designed for
altitudes greater than 2000 m or for environments with pollution degree 2 or higher, may require clearance and
creepage distances greater than 9 mm. Examples are OBC, DC/DC converters, and traction inverters for 800-V
automotive battery systems that support DC-bus voltages up to 1000 V.
The AMC1411-Q1 comes in a SOIC package with greater than 15.7 mm of creepage distance and is specifically
designed for use in high-voltage systems that require accurate voltage monitoring and reinforced isolation
between high-voltage and low-voltage parts of the system.
Figure 8-1 shows an OBC that uses the AMC1411-Q1 to monitor the DC-bus voltage that can be as high as
1000 V. The DC-bus voltage is divided down to an approximate 2-V level across the bottom resistor (RSNS)
of a high-impedance resistive divider that is sensed by the AMC1411-Q1. The output of the AMC1411-Q1 is a
differential analog output voltage of the same value as the input voltage but is galvanically isolated from the
high-side by a reinforced isolation barrier.
The wide creepage and clearance, high isolation voltage rating, and high common-mode transient immunity
(CMTI) of the AMC1411-Q1 ensure reliable and accurate operation in harsh and high-noise environments.
+ DC-Bus
DC-Link
Number of unit resistors depends
on design requirements.
See design examples for details.
DC/DC
EMI
Filter
PFC
Contactor
SW
RX1
RX2
L1
L2
L3
High-side supply
(3.3 V or 5 V)
Low-side supply
(3.3 V or 5 V)
SW
SW
100 nF 1 uF
AMC1411-Q1
VDD1
VDD2
10
10
10 nF
ICROSS
RSNS
IN
OUTP
OUTN
GND2
ADC
SHTDN
GND1
SW
N
1 uF 100 nF
N
‒ DC-Bus
Figure 8-1. Using the AMC1411-Q1 for DC Bus Voltage Sensing in an OBC
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
8.2.1 Design Requirements
Table 8-1 lists the parameters for this typical application.
Table 8-1. Design Requirements
PARAMETER
DC-bus voltage
VALUE
1000 V (maximum)
II
Overvoltage category
Altitude
≤4000 m
High-side supply voltage
3.3 V or 5 V
3.3 V or 5 V
100 V
Low-side supply voltage
Maximum resistor operating voltage
Voltage drop across the sense resistor (RSNS) for a linear response
Current through the resistive divider, ICROSS
2 V (maximum)
100 μA
8.2.2 Detailed Design Procedure
The 100-μA cross-current requirement at the maximum DC-bus voltage (1000 V) determines that the total
impedance of the resistive divider is 10 MΩ. The impedance of the resistive divider is dominated by the top
portion (shown exemplary as RX1 and RX2 in Figure 8-1) and the voltage drop across RSNS can be neglected
for a moment. The maximum allowed voltage drop per unit resistor is specified as 100 V; therefore, the minimum
number of unit resistors in the top portion of the resistive divider is 1000 V / 100 V = 10. The calculated unit
value is 10 MΩ / 10 = 1 MΩ and matches a value from the E96 series.
RSNS is sized such that the voltage drop across the resistor at the maximum DC-bus voltage (1000 V) equals
the linear full-scale range input voltage (VFSR) of the AMC1411-Q1, which is 2 V. This voltage is calculated as
RSNS = VFSR / (VDC-Bus, max – VFSR) × RTOP, where RTOP is the total value of the top resistor string (10 × 1 MΩ =
10 MΩ). RSNS is calculated as 20.04 kΩ. The next closest, lower value from the E96 series is 20 kΩ.
Table 8-2 summarizes the design of the resistive divider.
Table 8-2. Resistor Value Example
PARAMETER
VALUE
1 MΩ
Unit resistor value, RX
Number of unit resistors
10
Sense resistor value, RSNS
20 kΩ
Total resistance value
10.02 MΩ
99.8 μA
1.996 V
10 mW
99.8 mW
Resulting current through resistive divider, ICROSS
Resulting full-scale voltage drop across sense resistor RSNS
Power dissipated in unit resistor RX
Total power dissipated in resistive divider
Copyright © 2021 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
8.2.2.1 Insulation Coordination
In this example of an OBC, isolation between the high-voltage and low-voltage parts of the system is checked
against the requirements of the IEC60664-1 Insulation coordination for equipment within low-voltage systems
standard. Isolation must be designed to withstand the rated impulse voltage, temporary overvoltage, and the
working voltage. In addition, the physical distance between exposed metal parts on the high- and low-voltage
side must meet the minimum creepage and clearance requirements.
Table B.1 of the IEC60664-1 standard defines the impulse voltage for a 1000-V, unearthed system with OVC II
as 6000 V. This value is lower than the maximum VIOSM (8000 VPK) rating of the AMC1411-Q1.
Table B.1 of the IEC60664-1 standard also defines the system voltage of a 1000-V, unearthed system as 1000 V.
The temporary overvoltage for a system voltage of 1000 V is 2200 V and is derived using the formula (1200 V +
system voltage) from IEC60664-1. The value must be doubled for reinforced isolation, resulting in 4400 VRMS or
6250 VPK. This value is lower than the maximum VIOTM (10500 VPK) rating of the AMC1411-Q1.
The working voltage in this example is 1000 VDC and is also lower than VIOWM (2260 VDC) of the AMC1411-Q1.
The minimum clearance for a 6000-V impulse voltage according the IEC60664-1, table F.2, is 8.0 mm for
reinforced isolation. For reinforced insulation, the minimum clearance value is taken from the line corresponding
to the next higher impulse voltage rating (8000 V), following the guidelines for reinforced isolation. The
equipment is designed to operate at altitudes up to 4000 m above sea level and the minimum clearance must be
increased to 1.29 × 8 mm = 10.4 mm (rounded up). The factor of 1.29 is taken from table A.2 of the IEC60664-1
standard. The AMC1411-Q1 provides a minimum clearance of 14.7 mm and meets the requirement.
Finally, the minimum creepage distance for a working voltage of 1000 VDC, insulating material group I, pollution
degree 2, reinforced isolation is 2 × 5 mm = 10 mm according to IEC60664-1 table F.4. 5 mm is the value for
1000-V basic insulation and is doubled for reinforced isolation. The AMC1411-Q1 provides a minimum creepage
of 15.7 mm and provides significant margin against the minimum requirement.
8.2.2.2 Input Filter Design
Placing an RC filter in front of the isolated amplifier improves signal-to-noise performance of the signal path. In
practice, however, the impedance of the resistor divider is so high that adding a filter capacitor on the IN pin
limits the signal bandwidth to an unacceptable low limit, such that the filter capacitor is omitted. When used,
design the input filter such that:
•
•
The cutoff frequency of the filter is at least one order of magnitude lower than the sampling frequency
(20 MHz) of the internal ΔΣ modulator
The input bias current does not generate significant voltage drop across the DC impedance of the input filter
Most voltage-sensing applications use high-impedance resistor dividers in front of the isolated amplifier to scale
down the input voltage. In this case, a single capacitor (as shown in Figure 8-2) is sufficient to filter the input
signal.
VDC
R1
AMC1411-Q1
R2
VDD1
VDD2
OUTP
OUTN
GND2
1 nF
IN
RSNS
SHTDN
GND1
Figure 8-2. Input Filter
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
8.2.2.3 Differential-to-Single-Ended Output Conversion
Figure 8-3 shows an example of a TLV313-Q1-based signal conversion and filter circuit for systems using
single-ended input ADCs to convert the analog output voltage into digital. With R1 = R2 = R3 = R4, the output
voltage equals (VOUTP – VOUTN) + VREF. Tailor the bandwidth of this filter stage to the bandwidth requirement of
the system and use NP0-type capacitors for best performance. For most applications, R1 = R2 = R3 = R4 = 3.3
kΩ and C1 = C2 = 330 pF yields good performance.
C1
AMC1411-Q1
R2
VDD1
VDD2
OUTP
OUTN
GND2
R1
R3
IN
–
+
ADC
To MCU
SHTDN
GND1
TLV313-Q1
C2
R4
VREF
Figure 8-3. Connecting the AMC1411-Q1 Output to a Single-Ended Input ADC
For more information on the general procedure to design the filtering and driving stages of SAR ADCs, see
the 18-Bit, 1MSPS Data Acquisition Block (DAQ) Optimized for Lowest Distortion and Noise and 18-Bit Data
Acquisition Block (DAQ) Optimized for Lowest Power reference guides, available for download at www.ti.com.
8.2.3 Application Curve
One important aspect of system design is the effective detection of an overvoltage condition to protect switching
devices and passive components from damage. To power off the system quickly in the event of an overvoltage
condition, a low delay caused by the isolated amplifier is required. Figure 8-4 shows the typical full-scale step
response of the AMC1411-Q1.
VOUTP
VOUTN
VIN
Figure 8-4. Step Response of the AMC1411-Q1
Copyright © 2021 Texas Instruments Incorporated
24
Submit Document Feedback
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
8.3 What To Do and What Not To Do
Do not leave the analog input (IN) of the AMC1411-Q1 unconnected (floating) when the device is powered up
on the high-side. If the device input is left floating, the bias current may generate a negative input voltage that
exceeds the specified input voltage range and the output of the device is invalid.
Do not connect protection diodes to the input (IN) of the AMC1411-Q1. Diode leakage current can introduce
significant measurement error especially at high temperatures. The input pin is protected against high voltages
by its ESD protection circuit and the high impedance of the external restive divider.
9 Power Supply Recommendations
In a typical application, the high-side (VDD1) of the AMC1411-Q1 is powered from an already existing, high-side-
ground referenced 3.3-V or 5-V power supply in the system. Alternatively, the high-side supply can be generated
from the low-side supply (VDD2) by an isolated DC/DC converter. A low-cost solution is based on the push-pull
driver SN6501 and a transformer that supports the desired isolation voltage ratings.
The AMC1411-Q1 does not require any specific power-up sequencing. The high-side power supply (VDD1) is
decoupled with a low-ESR, 100-nF capacitor (C1) parallel to a low-ESR, 1-μF capacitor (C2). The low-side
power supply (VDD2) is equally decoupled with a low-ESR, 100-nF capacitor (C3) parallel to a low-ESR, 1-μF
capacitor (C4). Place all four capacitors (C1, C2, C3, and C4) as close to the device as possible. Figure 9-1
shows the proper decoupling layout for the AMC1411-Q1.
VDC
VDD1
VDD2
R1
R2
C2 1 µF
C4 1 µF
AMC1411-Q1
C1 100 nF
C3 100 nF
VDD1
VDD2
OUTP
OUTN
GND2
IN
to RC filter / ADC
to RC filter / ADC
RSNS
SHTDN
GND1
Figure 9-1. Decoupling of the AMC1411-Q1
Capacitors must provide adequate effective capacitance under the applicable DC bias conditions they
experience in the application. Multilayer ceramic capacitors (MLCC) typically exhibit only a fraction of their
nominal capacitance under real-world conditions and this factor must be taken into consideration when selecting
these capacitors. This problem is especially acute in low-profile capacitors, in which the dielectric field strength is
higher than in taller components. Reputable capacitor manufacturers provide capacitance versus DC bias curves
that greatly simplify component selection.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
25
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
10 Layout
10.1 Layout Guidelines
Figure 10-1 shows a layout recommendation with the critical placement of the decoupling capacitors (as close as
possible to the AMC1411-Q1 supply pins) and placement of the other components required by the device. For
best performance, place the sense resistor close to the device input pin (IN).
10.2 Layout Example
Clearance area, to be kept free
of any conductive materials.
C2
C1
C4
C3
to RC filter / ADC
to RC filter / ADC
IN
OUTP
OUTN
GND2
AMC1411-Q1
SHTDN
Top Metal
Inner or Bottom Layer Metal
Via
Figure 10-1. Recommended Layout of the AMC1411-Q1
Copyright © 2021 Texas Instruments Incorporated
26
Submit Document Feedback
Product Folder Links: AMC1411-Q1
AMC1411-Q1
SBASAB3 – OCTOBER 2021
www.ti.com
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
For related documentation, see the following:
•
•
•
•
Texas Instruments, Isolation Glossary application report
Texas Instruments, Semiconductor and IC Package Thermal Metrics application report
Texas Instruments, ISO72x Digital Isolator Magnetic-Field Immunity application report
Texas Instruments, TLVx313-Q1 Low-Power, Rail-to-Rail In/Out, 750-μV Typical Offset, 1-MHz Operational
Amplifier for Cost-Sensitive Systems data sheet
•
•
Texas Instrument, SN6501-Q1 Transformer Driver for Isolated Power Supplies data sheet
Texas Instruments, 18-Bit, 1-MSPS Data Acquisition Block (DAQ) Optimized for Lowest Distortion and Noise
design guide
•
Texas Instruments, 18-Bit, 1-MSPS Data Acquisition Block (DAQ) Optimized for Lowest Power reference
guide
•
•
Texas Instruments, Isolated Amplifier Voltage Sensing Excel Calculator design tool
Texas Instruments, Best in Class Radiated Emissions EMI Performance with the AMC1300B-Q1 Isolated
Amplifier application note
11.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. Click on
Subscribe to updates to register and receive a weekly digest of any product information that has changed. For
change details, review the revision history included in any revised document.
11.3 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
11.4 Trademarks
TI E2E™ is a trademark of Texas Instruments.
All trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
11.6 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
27
Product Folder Links: AMC1411-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
18-Nov-2021
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
AMC1411QDWLRQ1
ACTIVE
SOIC
DWL
8
500
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 125
1411Q
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF AMC1411-Q1 :
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
18-Nov-2021
Catalog : AMC1411
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Nov-2021
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
AMC1411QDWLRQ1
SOIC
DWL
8
500
330.0
24.4
18.55
7.2
4.5
24.0
24.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Nov-2021
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SOIC DWL
SPQ
Length (mm) Width (mm) Height (mm)
367.0 367.0 45.0
AMC1411QDWLRQ1
8
500
Pack Materials-Page 2
PACKAGE OUTLINE
DWL0008A
SOIC - 4.034 mm max height
S
C
A
L
E
1
.
2
5
0
PLASTIC SMALL OUTLINE
C
SEATING PLANE
17.4
17.1
A
PIN 1 ID AREA
0.1 C
6X 1.27
8
5
1
6.5
6.3
NOTE 3
2X
3.81
4
0.51
0.31
8X
(3.634)
14.1
13.9
NOTE 4
B
0.25
A B C
4.034 MAX
0.33
0.13
TYP
SEE DETAIL A
(1.625)
0.25
GAGE PLANE
0.3
0.1
1.1
0.6
0 -8
DETAIL A
TYPICAL
4224743/A 01/2019
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0,15 mm per side.
4. This dimension does not include interlead flash.
www.ti.com
EXAMPLE BOARD LAYOUT
DWL0008A
SOIC - 4.034 mm max height
PLASTIC SMALL OUTLINE
(14.25)
SYMM
(14.6)
8X (1.875)
8X (2)
SYMM
8X (0.6)
8X (0.6)
1
1
4
8
5
8
5
SYMM
SYMM
4
(R0.05)
TYP
(R0.05)
TYP
6X
(1.27)
6X
(1.27)
(16.475)
(16.25)
LAND PATTERN EXAMPLE
PCB CLEARANCE & CREEPAGE OPTIMIZED
EXPOSED METAL SHOWN
SCALE:3X
LAND PATTERN EXAMPLE
STANDARD
EXPOSED METAL SHOWN
SCALE:3X
0.07 MAX
ALL AROUND
0.07 MIN
ALL AROUND
EXPOSED METAL
EXPOSED METAL
METAL
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4224743/A 01/2019
NOTES: (continued)
5. Publication IPC-7351 may have alternate designs.
6. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DWL0008A
SOIC - 4.034 mm max height
PLASTIC SMALL OUTLINE
8X (2)
SYMM
1
4
8
SYMM
8X (0.6)
5
6X (1.27)
(16.25)
SOLDER PASTE EXAMPLE
STANDARD
BASED ON 0.125 mm THICK STENCIL
SCALE:4X
SYMM
8X (1.875)
8X (0.6)
1
4
8
5
SYMM
6X (1.27)
(16.475)
SOLDER PASTE EXAMPLE
PCB CLEARANCE & CREEPAGE OPTIMIZED
BASED ON 0.125 mm THICK STENCIL
SCALE:4X
4224743/A 01/2019
NOTES: (continued)
7. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
8. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明