MAAM-011186 [TE]
Differential CATV Variable Gain Amplifier;
| 型号： | MAAM-011186 |
| 厂家： | 
TE CONNECTIVITY |
| 描述： | Differential CATV Variable Gain Amplifier 有线电视 |
| 文件： | 总13页 (文件大小：1223K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MAAM-011186
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Features
Functional Schematic
39 dB Gain
31.5 dB, 0.5 dB steps, 6 Bit Digital Step
Attenuator
48
1
CMOS Control
36 dB MER, 64 QAM 39 Channels, 52 dBmV/ch.
8 V or 5 V Operation
3 dB Noise Figure
Serial or Parallel Attenuator Control
Differential Input and Output
Low Harmonics
3
4
34
33
7
8
30
29
Power Down Mode
Lead-Free 7 mm 48-Lead PQFN
Halogen-Free “Green” Mold Compound
RoHS* Compliant
11
12
26
25
Description
Pin Configuration3
The MAAM-011186 is an integrated 2 stage
differential amplifier with embedded digital step
attenuator (DSA) assembled in a lead-free 7 mm
48-lead PQFN package.
Pin
Pin
No.
Description
No.
Description
1
3
Latch Enable
30
32
33
Stage 2 Output (+)
Stage 2 Feedback (+)
Stage 2 Input (+)
This amplifier provides excellent linearity and high
output power with greater than 30 dB MER for
64 QAM modulation with 39 channels and 52 dBmV
per channel. Gain in the minimum attenuation state
is typically 39 dB. The internal DSA offers 31.5 dB
attenuation range with 0.5 dB steps. This device is
optimized for high output power and low current from
8 V bias but can also be operated from 5 V bias with
flexibility to adjust DC current with external
components. The module provides a power down
function for each of the amplifier stages.
Attenuator Input (+)
Stage 1 Output (+)
4
6
Stage 1 Feedback (+) 34
Attenuator Output (+)
DSA Serial Output
Power Up Select 2
Power Up Select 1
VDD CMOS Controller
7
Stage 1 Input (+)
Stage 1 Input (-)
36
37
8
9
Stage 1 Feedback (-) 38
11
12
16
Stage 1 Output (-)
Attenuator Input (-)
Enable Stage 1
39
40 Attenuator Bit 5 (16 dB)
41
Attenuator Bit 4 (8 dB)
Attenuator Bit 3 (4 dB)
Attenuator Bit 2 (2 dB)
Attenuator Bit 1 (1 dB)
This amplifier is ideally suited for use in CATV
reverse path applications.
18 Stage 1 Bias Voltage 42
19 Stage 2 Bias Voltage 43
Ordering Information1,2
21
Enable Stage 2
44
25 Attenuator Output (-) 45 Attenuator Bit 0 (0.5 dB)
Part Number
Package
26
Stage 2 Input (-)
46
Parallel/Serial Select
Clock
MAAM-011186-TR1000
MAAM-011186-TR3000
1000 piece reel
3000 piece reel
27 Stage 2 Feedback (-) 47
29
Stage 2 Output (-)
48
49
Serial Input
RF and DC Ground4
MAAM-011186-001SMB
MAAM-011186-002SMB
Sample Test Board, 8 V
Sample Test Board, 5 V
3. All pins not listed in the table are “No Connection” and should
be left unconnected.
4. The exposed pad centered on the package bottom must be
connected to RF and DC ground.
1. Reference Application Note M513 for reel size information.
2. All sample boards include 5 loose parts.
* Restrictions on Hazardous Substances, European Union Directive 2011/65/EU.
1
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011186
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Electrical Specifications: TA = +25°C, VCC = 8 V, Minimum attenuation state, Z0 = 75 Ω
Parameter
Gain
Test Conditions
Units
dB
Min.
37.5
—
Typ.
39.0
1.2
3.0
22
Max.
41.0
—
Max. Gain State @ 100 MHz, -29 dBm PIN
Gain Slope
Positive tilt from 5 - 250 MHz
dB
Noise Figure5
Input Return Loss
Output Return Loss
Reverse Isolation
Attenuation Range
—
dB
—
—
—
dB
—
—
—
dB
—
22
—
—
dB
—
50
—
100 MHz relative to max. attenuation gain, -29 dBm PIN
dB
30.0
31.5
33.0
39 Channels (5-250 MHz), 52 dBmV/Ch.
Single Channel (8-200 MHz), 72 dBmV/Ch.
Single Channel (250 MHz), 71 dBmV/Ch.
16 Channels (5-250 MHz), 57 dBmV/Ch.
—
30
—
30
36
35
35
34
64 QAM MER6
dB
—
P1dB
OIP2
—
dBm
dBm
dBm
ns
—
—
—
—
—
—
—
27
70
—
—
—
—
315
5
2-tone, 12 dBm/tone, 1 MHz tone spacing, 200 MHz
2-tone, 12 dBm/tone, 1 MHz tone spacing, 200 MHz
50% Control to 90 / 10 % RF
EN1 = EN2 = 5 V
OIP3
42
TON, TOFF
ICC
ICC_OFF
IEN1, IEN2
400
280
3
mA
EN1 = EN2 = 0 V
mA
EN1 = EN2 = 5 V
mA
0.7
—
5. Includes Balun Loss.
6. Modulation error ratio each channel 64 QAM 5.12 MS/s.
Truth Table11
Absolute Maximum Ratings7,8,9
Parameter
RF Input Power
Absolute Maximum
-8 dBm
B5 B4 B3 B2 B1
B0
1
Attenuation (dB)
1
1
1
1
1
1
0
0
1
1
1
1
1
0
1
0
1
1
1
1
0
1
1
0
1
1
1
0
1
1
1
0
1
1
0
1
1
1
1
0
Minimum
Voltage
10 Volts
0
0.5
1
Control Voltage
-0.5 to +5.5 Volts
+150°C
1
Junction Temperature10
Operating Temperature
Storage Temperature
1
2
-40°C to +100°C
-65°C to +150°C
1
4
1
8
7. Exceeding any one or combination of these limits may cause
permanent damage to this device.
1
16
31.5
8. M/A-COM Technology Solutions does not recommend
sustained operation near these survivability limits.
9. Operating at nominal conditions with TJ ≤ 150°C will ensure
0
11. Logic “0” = 0.0 V to 0.8 V ± 0.2 V,
MTTF > 1 x 106 hours.
Logic “1” = 2.0 V to 5.0 V ± 0.2 V
10. Junction Temperature (TJ) = TC + Өjc * (V * I)
Typical thermal resistance (Өjc) = 9° C/W.
a) For TC = +25°C,
TJ = 47°C @ 8 V, 315 mA
b) For TC = +100°C,
TJ = 122°C @ 8 V, 315 mA
2
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011186
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
PCB Layout
C26
Application Schematic
4
2
4
1
5
5
3
3
1
2
C26
3
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011186
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Parts List : 8 V Application circuit
Part
Value
0.1 µF
0.1 µF
47 pF
1 µF
Case Style
0402
0402
0402
0805
0402
0806
0402
0402
0402
0402
0402
0402
0402
0402
0402
0402
0402
0402
-
Function/Notes
RF Bypass
C1, C9, C13, C20,
C21, C22, C23, C24
C2, C4, C5, C6, C7, C8, C11,
C12, C14, C15, C16, C17, C18
DC Block
C3, C19
C25
Gain Tilt (with R16 and R17)
Low Frequency Bypass
Input Match
DNI
(Do not install)
C26
L1, L12
L2, L11
L3, L10
L4, L9
L5, L8
L6, L7
L13
47 µH
250 nH
18 nH
8.2 nH
27 nH
30 nH
5.6 nH
3 kΩ
Stage1 VCC Choke. Murata LQH2MCN470K02L
Gain Tilt (With R7 & R14). Coilcraft 0402AF-251XJLU
Input Match Stage2 Amp
Output Match Stage1 Amp
Input Match Stage2 Amp
Output Match Stage2 Amp
Input Match
R212
Voltage Divider for VDD CMOS
Voltage Divider for VDD CMOS
Gain Tilt (with L2 & L11)
R412
5 kΩ
R7, R14
R16, R17
R8
249 Ω
27 Ω
Gain Tilt (with C3 & C19)
10 kΩ
100 Ω
Set Current for Stage1 Amp. Lower to Reduce Current.
Drop VCC1 to 5 V. PDISS 1/10 W
R10, R11
R5, R6
T1, T2
DNI
(Do not install)
May be used to increase Stage 2 current for
lower VCC applications.
1:2
MABA-011029 (MABA-011050 alternate)13
12. These components may be omitted if direct connection to 3 - 5 V bias is available for VDD_CMOS.
13. If using MABA-011050 balun: L5,L8 = 30 nH, L6,L7= 33 nH, C26 = 1 pF.
4
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011186
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Typical Performance Curves: VCC = 8 V
Gain
Gain - Wideband
60
40
40
20
Max. Gain
B0 = 0
B1 = 0
B3 = 0
B4 = 5
B6 = 0
Max. Atten.
30
20
B2 = 0
0
Max. Gain
B0 (-0.5 dB)
B1 (-1 dB)
B2 (-2 dB)
B3 (-4 dB)
B4 (-8 dB)
B5 (-16 dB)
Min. Gain (-31.5)
-20
-40
-60
10
0
0
500
1000
1500
2000
2500
3000
0
100
200
300
400
400
400
Frequency (MHz)
Frequency (MHz)
Output Return Loss
Input Return Loss
0
0
Max. Gain
B0 (-0.5 dB)
B1 (-1 dB)
B2 (-2 dB)
B3 (-4 dB)
B4 (-8 dB)
B5 (-16 dB)
Max. Gain
B0 (-0.5 dB)
B1 (-1 dB)
B2 (-2 dB)
B3 (-4 dB)
B4 (-8 dB)
B5 (-16 dB)
Min. Gain (-31.5)
-10
-20
-30
-40
-10
-20
-30
-40
Min. Gain (-31.5)
0
100
200
300
0
100
200
300
400
Frequency (MHz)
Frequency (MHz)
Reverse Isolation
Noise Figure
-30
5
Max. Gain
B0 (-0.5 dB)
B1 (-1 dB)
B2 (-2 dB)
B3 (-4 dB)
B4 (-8 dB)
B5 (-16 dB)
Min. Gain (-31.5)
-40
-50
-60
-70
-80
-90
4
3
2
1
+25°C
-40°C
+85°C
0
0
0
100
200
300
100
200
300
400
Frequency (MHz)
Frequency (MHz)
5
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011186
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Typical Performance Curves: VCC = 8 V
Gain
POUT @ 30 dB MER
75
45
70
65
60
55
50
40
35
+25°C
-40°C
+85°C
30
25
0
8
16
24
32
40
0
100
200
300
400
Number of 64 QAM Channels
Frequency (MHz)
Modulation Error Ratio (64 QAM, 16 channel)
Modulation Error Ratio (64 QAM, single channel)
60
50
45
40
35
50
40
30
FC = 56 MHz
FC = 250 MHz
30
FC = 156 MHz
FC = 200 MHz
FC = 100 MHz
FC = 14 MHz
FC = 207 MHz
25
20
20
40
45
50
55
60
65
70
75
25
30
35
40
45
50
55
60
Output Power (dBmV)
Output Power (dBmV)
Modulation Error Ratio (64 QAM, 32 channel)
Modulation Error Ratio (64 QAM, 40 channel)
50
50
45
40
45
40
35
35
FC = 14 MHz
FC = 14 MHz
FC = 32 MHz
30
30
FC = 32 MHz
FC = 56 MHz
FC = 104 MHz
FC = 146 MHz
FC = 56 MHz
FC = 104 MHz
25
25
FC = 146 MHz
FC = 194 MHz
FC = 237 MHz
FC = 194 MHz
20
20
30
35
40
45
50
55
60
30
35
40
45
50
55
60
Output Power (dBmV)
Output Power (dBmV)
6
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011186
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Lead-Free 7 mm 48-lead PQFN
†
Reference Application Note S2083 for lead-free solder reflow recommendations.
Meets JEDEC moisture sensitivity level 3 requirements.
Plating is NiPdAuAg.
Recommended Land Pattern
0.508 mm
0.3 mm
0.254 mm
0.2 mm
Handling Procedures
0.8 mm
Please observe the following precautions to avoid
damage:
0.305 mm
Static Sensitivity
0.432 mm
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
HBM Class 1B devices.
7.8 mm
0.864 mm
5.8 mm
0.2 mm
Copper plating (board and vias) should be ≥ 0.05 mm thick.
7
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011186
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Applications Section
5 V Application
The MAAM-011186 may also be operated from 5 V VCC supply with adjustment of a few external components.
Resistors R5 and R6 may be used to increase output stage current and output power.
Typical Performance: TA = +25°C, VCC = 5 V, Minimum attenuation state, Z0 = 75 Ω
Parameter
Gain
Test Conditions
Units
dB
Typ.
39
Max. Gain State @ 100 MHz, -29 dBm PIN
Gain Slope
Noise Figure
Input Return Loss
Output Return Loss
Reverse Isolation
Attenuation Range
64 QAM MER6
P1dB
Positive tilt from 5 - 250 MHz
dB
1.2
3.0
22
—
dB
—
dB
—
dB
22
—
dB
50
100 MHz relative to max. attenuation gain, -29 dBm PIN
16 Channels (5 - 250 MHz), 53 dBmV/Ch.
—
dB
31.5
34
dB
dBm
dBm
dBm
mA
23
OIP2
2-tone, 6 dBm/tone, 1 MHz tone spacing, 200 MHz
2-tone, 6 dBm/tone, 1 MHz tone spacing, 200 MHz
EN1 = EN2 = 5 V (R5 = R6 = 7.5 kΩ)
70
OIP3
37
ICC
190
Typical Performance Curves: VCC = 5 V
Modulation Error Ratio (64 QAM, 16 channel)
Modulation Error Ratio (64 QAM, 16 channel)
50
50
5V, 190 mA
Fc = 156 MHz
45
45
40
35
30
25
20
40
35
30
FC = 56 MHz
5 V, 145 mA
5 V, 190 mA
5 V, 280 mA
FC = 156 MHz
FC = 207 MHz
25
20
25
30
35
40
45
50
55
60
25
30
35
40
45
50
55
60
Output Power (dBmV)
Output Power (dBmV)
8
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011186
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Parts List14: 5 V Application circuit, 190 mA typical
Part
Value
0.1 µF
0.1 µF
47 pF
1 µF
Case Style
0402
0402
0402
0805
0402
0806
0402
0402
0402
0402
0402
0402
0402
0402
0402
0402
0402
0402
-
Function/Notes
RF Bypass
C1, C9, C13, C20,
C21, C22, C23, C24
C2, C4, C5, C6, C7, C8, C11,
C12, C14, C15, C16, C17, C18
DC Block
C3, C19
C25
Gain Tilt (with R16 and R17)
Low Frequency Bypass
Input Match
C26
1 pF
L1, L12
L2, L11
L3, L10
L4, L9
L5, L8
L6, L7
L13
47 µH
250 nH
18 nH
8.2 nH
30 nH
33 nH
5.6 nH
0 Ω
Stage1 VCC Choke. Murata LQH2MCN470K02L
Gain Tilt (With R7 & R14). Coilcraft 0402AF-251XJLU
Input Match Stage2 Amp
Output Match Stage1 Amp
Input Match Stage2 Amp
Output Match Stage2 Amp
Input Match
R2
Voltage Divider for VDD CMOS
Voltage Divider for VDD CMOS
Gain Tilt (with L2 & L11)
R4
DNI
R7, R14
R16, R17
R8
249 Ω
27 Ω
Gain Tilt (with C3 & C19)
0 Ω
Set Current for Stage1 Amp. Lower to Reduce Current.
Drop VCC1 to 5 V. PDISS 1/10 W
Set current for Stage 2 Amp.
MABA-011050
R10, R11
R5, R614
T1, T2
0 Ω
7.5 kΩ
1:2
14. With resistor R5 & R6 installed Stage 2 current will not be fully shut down when EN2 = 0
Total Current vs. R5, R6 Resistor Value (R8 = 0 Ω)
R5, R6 Value
Total Current
DNI
145 mA
7.5 kΩ
190 mA
4.3 kΩ
210 mA
1.5 kΩ
275 mA
9
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011186
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Functionality
Modes of Operation: Serial, Direct Parallel, and Latched Parallel
Mode Truth Table
P/S
1
LE
X
Mode
Serial
0
Constant High
Pulsed
Direct Parallel
Latched Parallel
0
Serial Mode
The serial control interface (SERIN, CLK, LE, SEROUT) is compatible with the SPI protocol. SPI mode is
activated when P/S is kept high. The 6-bit serial word must be loaded with MSB first. After shifting in the 6 bit
word, bringing LE high will set the attenuator to the desired state. While LE is high the CLK is masked to protect
the data while implementing the change . SEROUT is the SERIN delayed by 6 clock cycles.
When P/S is low, the serial control interface is disabled and the serial input register is loaded asynchronously with
parallel digital inputs.
Direct Parallel Mode
The parallel mode is enabled when P/S is set to low. In the direct parallel mode, the attenuator is controlled by the
parallel control inputs directly. The LE must be at logic high to control the attenuator in this mode.
Latched Parallel Mode
In the latched parallel mode, the parallel control inputs will be buffered by registers, and loaded to the outputs
when LE is high. The outputs shall not change states when LE is low.
Power-up States
The power-up (PUP) states will work in both serial and parallel modes, and initiate the attenuator according to the
PUP truth table. During power up, the digital inputs shall be held constant for at least 1 μs after VCC reaches 90%
of final value. For serial mode, the PUP states will only work when LE is held low. The PUP state shall be locked
out after the first LE pulse. Proper operation of power up states requires fast rise time (<200 ns) for VDD-CMOS.
10
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011186
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Functionality
Modes of Operation: Serial, Direct Parallel, and Latched Parallel
PUP Truth Table
Inputs
Gain Relative to Max. Gain
Notes
PS
0
LE
0
PUP2
PUP1
0
0
1
1
X
X
X
0
1
0
1
X
X
X
-31.5 dB
-24 dB
0
0
0
0
-16 dB
Parallel Mode
Serial Mode
0
0
0 dB
0
1
0 to –31.5 dB (Set B0 - B5)
0 to –31.5 dB (Set B0 - B5)
No Definition
1
0
1
1
Serial Interface Timing Characteristics
Typical Performance
25°C
Symbol
Parameter
Units
-40°C
100
20
+85°C
100
20
tSCK
tCS
Min. Serial Clock Period
Min. Control Set-up Time
Min. Control Hold Time
Min. LE Set-up Time
100
20
ns
ns
ns
ns
ns
ns
ns
tCH
20
20
20
tLS
10
10
10
tLEW
tLH
Min. LE Pulse Width
10
10
10
Min. Serial Clock Hold Time from LE
Min. LE Pulse Spacing
10
10
10
tLES
630
630
630
11
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011186
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Functionality
Modes of Operation: Serial, Direct Parallel, and Latched Parallel
Serial Input Interface Timing Diagram
tLS tLEW tLH
SERIAL
CLK
LE
tLES
D5
MSB
D0
LSB
CONTROL
WORD
D4
D1
tCS
tCH
Parallel Control Word
tLEW
LE
tLS
tLH
30ns Minimum
12
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011186
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
M/A-COM Technology Solutions Inc. All rights reserved.
Information in this document is provided in connection with M/A-COM Technology Solutions Inc ("MACOM")
products. These materials are provided by MACOM as a service to its customers and may be used for
informational purposes only. Except as provided in MACOM's Terms and Conditions of Sale for such products or
in any separate agreement related to this document, MACOM assumes no liability whatsoever. MACOM
assumes no responsibility for errors or omissions in these materials. MACOM may make changes to
specifications and product descriptions at any time, without notice. MACOM makes no commitment to update
the information and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future
changes to its specifications and product descriptions. No license, express or implied, by estoppels or otherwise,
to any intellectual property rights is granted by this document.
THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, RELATING TO SALE AND/OR USE OF MACOM PRODUCTS INCLUDING LIABILITY OR
WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR
INCIDENTAL DAMAGES, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR
OTHER INTELLECTUAL PROPERTY RIGHT. MACOM FURTHER DOES NOT WARRANT THE ACCURACY
OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN
THESE MATERIALS. MACOM SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS,
WHICH MAY RESULT FROM THE USE OF THESE MATERIALS.
MACOM products are not intended for use in medical, lifesaving or life sustaining applications. MACOM
customers using or selling MACOM products for use in such applications do so at their own risk and agree to
fully indemnify MACOM for any damages resulting from such improper use or sale.
13
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
相关型号：
©2020 ICPDF网 联系我们和版权申明