D14148-000 [TE]
PolySwitch? PTC Devices; PolySwitch® PTC器件
| 型号： | D14148-000 |
| 厂家： | 
TE CONNECTIVITY |
| 描述： | PolySwitch? PTC Devices |
| 文件： | 总2页 (文件大小：95K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
PRODUCT: AGRF1100
PolySwitch®
DOCUMENT: SCD25238
PCN: D14148
REV LETTER: C
PTC Devices
308 Constitution Drive
Overcurrent Protection Device
Menlo Park, CA 94025-1164
Phone: 800-227-4856
www.circuitprotection.com
REV DATE: MAY 13, 2011
PAGE NO.: 1 OF 2
Specification Status:RELEASED
Electrical Rating
Voltage: 16VDC MAX
Insulating Material:
Cured, Flame Retardant Epoxy Polymer
Lead Material:
20 AWG Tin Plated Copper
(0.8 mm [0.032] nom. diameter)
Part Marking:
Manufacturer’s Mark
and Voltage
16
GF11
Part Identification
Lot Identification
(can be on back)
TABLE I. INSTALLATION ENVELOPE DIMENSIONS:
A
B
C
D
E
F
G
MIN
--
--
MAX
17.5
(0.69)
MIN
--
--
MAX
26.5
(1.04)
MIN
4.3
(0.17)
MAX
5.8
(0.23) (0.30)
MIN
7.6
MAX
--
--
MIN
--
--
MAX
3.0
(0.12) (0.05)
TYP
1.2
MIN
--
--
MAX
7.47
(0.294)
mm:
in*:
*Rounded off approximation
TABLE II. PERFORMANCE RATINGS:
CURRENT RATINGS
TIME TO
TRIP
INITIAL
RESISTANCE
TRIPPED-
STATE
POWER
R1 MAX
RA MAX
1 HR. POST TRIP
RESISTANCE
STANDARD TRIP
OHMS
DISSIPATION
AMPS
AT 25°C
HOLD HOLD TRIP
SECONDS
AT 25°C, 55 A
MAX
OHMS
AT 25°C
OHMS
AT 25C
WATTS AT
25°C
AT 25C
MIN
MAX
TYP
AT
R1 MAX RA MAX
11.0 10.5
AT
20.3
7.5
0.0033
0.0060
0.0089
0.0093
3.7
Reference Documents:
Precedence:
PS400, PS300 (reference for R1 MAX)
This specification takes precedence over documents referenced herein.
Effectivity:
CAUTION:
Reference documents shall be the issue in effect on the date of invitation for bid.
Operation beyond the rated voltage or current may result in rupture, electrical arcing or flame.
Materials Information
ROHS Compliant
ELV Compliant
Pb-Free
PRODUCT: AGRF1100
PolySwitch®
DOCUMENT: SCD25238
PCN: D14148
REV LETTER: C
PTC Devices
308 Constitution Drive
Overcurrent Protection Device
Menlo Park, CA 94025-1164
Phone: 800-227-4856
www.circuitprotection.com
REV DATE: MAY 13, 2011
PAGE NO.: 2 OF 2
TABLE III. AUTOMOTIVE SPECIFIC STRESS TESTS AND TEST CONDITIONS:
ELECTRICAL STRESS TESTS
TEST CONDITIONS (see note 2)
ESD Voltage Withstand
(see note 1)
25kV
Short Circuit Fault Current Durability
25 cycles, 16V, 200A
Fault Current Durability
350 cycles, 16V/100A
1750 cycles, 16V/100A
3 cycles, 26V, 1 minute duration
10 cycles, 86.5V
End-of-life Mode Verification
Jump Start Endurance
(see note 1)
Load Dump Endurance
(see note 1)
Note 1: The PolySwitch devices are tested in series with a load resistance and the voltages specified in the test conditions are
shared between the PolySwitch device and the load resistance as specified in PS400.
Note 2: Please refer to Appendix A of PS400 for the detailed test procedures
© 2004, 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company. All rights reserved.
相关型号：
©2020 ICPDF网 联系我们和版权申明