2063149-2 [TE]
Small Form-Factor Pluggable (SFP) and zSFP;型号: | 2063149-2 |
厂家: | TE CONNECTIVITY |
描述: | Small Form-Factor Pluggable (SFP) and zSFP |
文件: | 总3页 (文件大小:92K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Instruction Sheet
Small Form-Factor Pluggable (SFP)+ and zSFP+
Extraction Tool Kits 2063048-[ ] and 2161405-1
for Stacked PT Connector and Cage Assemblies
408-10259
19 AUG 13 Rev D
Extraction Tool
Cutout (2 Places)
Top Push Plate
Printed Circuit (PC)
Board (Ref)
Wall Supports
2 x 4 Stacked SFP+ Connector
and Cage Assembly
(2007538-1 Shown)
Finger Mounting Block
Base Plate
SFP+ CONNECTOR AND CAGE
zSFP+ CONNECTOR AND CAGE
EXTRACTION TOOL
ASSEMBLY CONFIGURATION
ASSEMBLY CONFIGURATION
2063048-1
2063048-2
2063048-3
2063048-4
2063048-5
2063048-6
2161405-1
2 x 4
2 x 1
2 x 2
2 x 6
---
2 x 4
2 x 1
2 x 2
2 x 6
2 x 5
2 x 8
2 x 12
---
2 x 12
Figure 1
The base plate features a finger mounting block that
holds up to six wall supports to the base plate. See
Figure 1. The top push plate is designed to be
installed onto the upper tooling and the base plate is
designed to be installed onto the lower tooling of the
application tool. The extraction tool has cutouts (one
located on each side) to accept the protruding part of
the cage assembly. Each “finger” of a wall support fits
into a port of the cage assembly.
1. INTRODUCTION
SFP+ and zSFP+ Extraction Tool Kits 2063048-[ ] and
2161405-1 are used to remove the pc board from
SFP+ and zSFP+ stacked PT connector and cage
assemblies described in Figure 1. The connectors and
cage assemblies contain press-fit contacts. Read
these instructions thoroughly before using the
extraction tool kit.
Reasons for reissue of this instruction sheet are
provided in Section 7, REVISION SUMMARY.
During extraction, the back and sides of the extraction
tool protect the cage assembly from damage, the wall
supports support the individual ports of the cage
assembly, and the top push plate provides a surface to
apply an even force to extract the pc board from the
connector and cage assembly.
Dimensions on this sheet are in metric units [with
U.S. customary units in brackets]. Figures and
NOTE
illustrations are for reference only and are not
drawn to scale.
i
3. APPLICATION TOOLING REQUIREMENT
2. DESCRIPTION
Power for the extraction tool must be provided by
application tools (with a ram) capable of supplying a
downward force of 44.5 N [10 lb] per contact.
Each extraction tool kit consists of an extraction tool, a
top push plate, base plate, and wall supports (one for
each stacked row of the cage assembly).
©2013 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change.
1 of 3
All Rights Reserved
*Trademark
PRODUCT INFORMATION 1-800-522-6752
For latest revision and Regional Customer Service,
visit our website at www.te.com
LOC B
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
408-10259
Manual Arbor Frame Assembly 58024-1 is available
for use with these extraction tool kits. Refer to
Instruction Sheet 408-6923 for operating procedure.
5. Cycle the application tool to extract the pc board
from the connector and cage assembly. Then retract
the ram, and carefully remove the extraction tool
(with the connector and cage assembly) from the
wall supports.
Over-driving of the extraction tool could cause
CAUTION
damage to the connector or cage assembly.
!
5. MAINTENANCE AND INSPECTION
The extraction tool kit is inspected before shipment. It
is recommended that the extraction tool kit be
inspected immediately upon arrival at your facility to
ensure that it has not been damaged during shipment
and that it conforms to the dimensions provided in
Figure 3.
4. EXTRACTION PROCEDURE
1. Ensure that the amount of wall supports installed
onto the finger mounting block matches the amount
of ports of the cage assembly. It is recommended to
center the group of wall supports on the finger
mounting block. Refer to Figure 1.
5.1. Daily Maintenance
2. Install the top push plate onto the upper tooling
and the base plate (with the wall supports) onto the
lower tooling of the application tool. See Figure 2.
It is recommended that each operator be made aware
of, and responsible for, the following steps of daily
maintenance:
Ensure that the upper tooling and lower tooling are
secure; otherwise, damage to the connector and
cage assembly could occur.
1. Remove dust, moisture, and contaminants with a
clean, soft brush or a lint-free cloth. DO NOT use
objects that could damage the extraction tool kits
components.
CAUTION
!
3. Place the open end of the extraction tool over the
cage assembly so that the cutouts align with the
protruding part (at the back) of the cage assembly.
Make sure that the sides of the extraction tool sit on
the pc board.
2. When the extraction tool kit is not in use, store it
in a clean, dry area.
5.2. Periodic Inspection
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the extraction tool kit or be
supplied to personnel responsible for the extraction
tool kit. Inspection frequency should be based on
amount of use, working conditions, operator training
and skill, and established standards.
4. Slide the extraction tool (with the connector and
cage assembly and pc board) onto the wall supports
so that each “finger” of each wall support enters a
port of the cage assembly. Make sure the fingers
are fully inserted into the ports. See Figure 2.
6. REPLACEMENT AND REPAIR
Application Tool
Ram
Side View
Customer-replaceable parts are listed in Figure 3. A
complete inventory should be stocked and controlled
to prevent lost time when replacement of parts is
necessary. Parts other than those listed should be
replaced by TE Connectivity to ensure quality and
reliability. Order replacement parts through your TE
Representative, or call 1-800-526-5142, or send a
facsimile of your purchase order to 717-986-7605, or
write to:
Top Push
Plate
Fingers of Wall
Supports Fully
Inserted into
SidesofExtraction
Tool Sitting on PC
Board
Cage Assembly
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
PC Board
HARRISBURG PA 17105-3608
7. REVISION SUMMARY
• Updated document to corporate requirements
• Added new extraction tool kit part number to title,
Section 1, and tables in Figures 1 and 3
Base Plate (with
Wall Supports)
Lower Tooling of
Application Tooling
• Changed information in tables in Figure 3
• Deleted dimensions and artwork in Figure 3
Figure 2
2 of 3
Rev D
408-10259
2 x 4 Extraction Tool Kit Shown
2
40.4 [1.591]
-A-
1
6.35 [.250]
40.4 [1.591]
58.7 [2.311]
B
101.6
[4.00]
101.6 [4.00]
3
4
54.6 [2.15]
50.8 [2.00]
25.4
[1.00]
5
TOOL (By Product Configuration)
DIMENSION “A” (mm [in.])
18.8 [.740]
DIMENSION “B” (mm [in.])
2 x 1
2 x 2
2 x 4
2 x 5
2 x 6
2 x 8
2 x 12
33.5 [1.3219]
61.6 [2.425]
114.3 [4.500]
76.3 [3.004]
90.1 [3.547]
119.6 [4.708]
175.8 [6.921]
199.9 [7.872]
REPLACEMENT PARTS
PART NUMBER (By Product Configuration)
QTY PER TOOL
ITEM
DESC
2 x 1
2 x 2
2 x 4
2 x 5
2 x 6
2 x 8
2 x 12
2 x 1
2 x 2
2 x 4
2 x 5
2 x 6
2 x 8
2 x 12
TOOL,
1
2
3
4
2063149-2
2063149-3
2063149-1
2063149-5
2063149-4
2063149-8
2161405-1
1
1
1
1
1
4
1
1
1
1
Extraction
PLATE,
Top Push
2161356-1
2161404-1
2161402-1
1
1
1
1
1
2
1
1
5
1
1
6
1
1
8
1
1
PLATE,
Base
2161354-1
2063051-1
SUPPORT,
Wall
12
MOUNTING
BLOCK,
Finger
5
2161355-1
2161403-1
1
1
1
1
1
1
1
Figure 3
3 of 3
Rev D
相关型号:
©2020 ICPDF网 联系我们和版权申明