1-307275-6 [TE]
Application and Maintenance for Crimping Die Assemblies for Tape-Mounted PIDG and PLASTI-GRIP Terminals and Splices;型号: | 1-307275-6 |
厂家: | TE CONNECTIVITY |
描述: | Application and Maintenance for Crimping Die Assemblies for Tape-Mounted PIDG and PLASTI-GRIP Terminals and Splices |
文件: | 总7页 (文件大小:510K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Instruction Sheet
Application and Maintenance for Crimping
Die Assemblies for Tape-Mounted PIDG*
and PLASTI-GRIP* Terminals and Splices
408-2423
08 APR 14 Rev B
Die Holding
Screw
Moving Die
Wire Barrel
Crimper
Saddle Screw
Saddle
Insulation
Anvil
Color Code
Dot
Color Code
Dot
Insulation
Crimper
Wire Barrel
Anvil
Die Holding
Screw
Stationary Die
Figure 1
1. INTRODUCTION
The crimping dies listed on this instruction sheet are recommended for crimping the PIDG and PLASTI-GRIP
tape-mounted terminals and splices indicated in Figure 2. The PIDG terminals and splices are used on
stranded copper wire, and the PLASTI-GRIP terminals and splices are used with solid or stranded copper wire.
The dies are designed to be used in AMP-TAPETRONIC* Machine 69875. Refer to Customer Manual
409-1993, packaged with the machine, for information concerning die installation, crimp adjustments, crimping
procedures, and general operation of the machine.
This instruction sheet covers die selection, crimping instructions, and die maintenance and inspection
procedures. Read these instructions thoroughly before crimping any terminals or splices.
NOTE
Measurements are in millimeters [followed by inch equivalents in brackets]. Figures and illustrations are for identification only
and are not drawn to scale.
Reasons for reissue are provided in Section 7, REVISION SUMMARY.
2. DESCRIPTION (Figure 1)
Each die assembly features two stationary dies (anvils) and two moving dies (crimpers), a saddle, and
attaching hardware. One pair of dies (one anvil and one crimper) forms a crimping chamber for the terminal or
splice wire barrel, and the other pair of dies crimps the insulation barrel.
Each half of the die assembly is secured in the machine by a captive screw. The dies are color coded
according to wire size for easy identification. When the terminal or splice is properly crimped in the correct dies,
one or two dots (depending on wire size) will appear on the top and bottom of the terminal or splice.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com.
© 2014 TE Connectivity family of companies
All Rights Reserved
*Trademark
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
1 of 7
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
408-2423
PLASTI-GRIP
Butt Splice
PIDG
Butt Splice
PLASTI-GRIP
Terminal
PIDG
Terminal
PIDG FASTON
Receptacle
Color Stripe
on Radiation
Resistant
Color Stripe on 16-14
HD and Radiation
Resistant
Color Stripe
on 16-14 HD
Crimp Dot Code
Crimp Dot Code
Wire Strip Length, mm [in.]
Wire Size
Range
(AWG)
Dot Code
(Number
of Dots)
Insulation
Color Code
Die Assembly
Part Number
Product
Terminal
Splice
Min
4.37
Min
Max
Max
3.97
4.76
5.16
26-22
26-24
24-20
Yellow
Yellow
White
Red
1
1
2
1
2
1
1
1
1
1
69877
69872, 68208-1 Lg Exp
69878
[5/32]
[3/16]
[11/64] [13/64]
5.16
5.95
6.35
[1/4]
7.14
[9/32]
[13/64] [15/64]
4.76
[3/16]
5.56
[7/32]
5.56
[7/32]
6.35
[1/4]
5.16
5.95
6.35
[1/4]
7.14
[9/32]
22-16
16-14
69872, 68208-1 Lg Exp
69873, 68207-1 Lg Exp
69874
[13/64] [15/64]
5.16 5.95
20-16 HD [13/64] [15/64]
6.35
[1/4]
9.53
[3/8]
PIDG and PLASTI-GRIP
Terminals and Splices
(Except 12-10 PIDG
Window Splice
Blue
7.94
[5/16]
8.73
[11/32]
8.73
[11/32]
9.53
[3/8]
12-10
16-14 HD
12-10
Yellow
7.94
[5/16]
8.73
[11/32]
8.73
[11/32]
9.53
[3/8]
Yellow with
Black Stripe
69874
7.94
[5/16]
8.73
[11/32]
8.73
[11/32]
9.53
[3/8]
Yellow
69897 Lg Exp
69897 Lg Exp
68116-1₸
7.94
[5/16]
8.73
[11/32]
8.73
[11/32]
9.53
[3/8]
Yellow with
Black Stripe
16-14 HD
8
8.33
9.13
9.13
[23/64]
9.53
[3/8]
Red
[21/64] [23/64]
₸ Long tongue PLASTI-GRIP terminals only.
Figure 2 (Part 1 of 2)
Rev B
2 of 7
408-2423
PLASTI-GRIP
Butt Splice
PIDG
Butt Splice
PLASTI-GRIP
Terminal
PIDG
Terminal
PIDG FASTON
Receptacle
Color Stripe
on Radiation
Resistant
Color Stripe on 16-14
HD and Radiation
Resistant
Color Stripe
on 16-14 HD
Crimp Dot Code
Crimp Dot Code
Wire Strip Length, mm [in.]
Dot
Code
(Number
of Dots)
Wire Size
Range
(AWG)
Insulation
Color Code
Die Assembly
Part Number
Product
Terminal
Splice
Min
Min
Max
Max
4.76
[3/16]
5.56
[7/32]
5.56
[7/32]
6.35
[1/4]
Natural with
White Stripe
24-20
22-16
2
1
2
1
1
1
2
1
2
69878
69872
69873
69874
69874
69935
69936
69937
69938
5.16
5.95
6.35
[1/4]
7.14
[9/32]
Natural with
Red Stripe
[13/64] [15/64]
PDIG Radiation
Resistant Terminals and
Splices
5.16 5.95
[13/64] [15/64]
6.35
[1/4]
7.14
[9/32]
Natural with
Blue Stripe
16-14
12-10
16-14 HD
26-24
22-20
18-16
14
7.94
[5/16]
8.73
[11/32]
6.35
[1/4]
7.14
[9/32]
Natural with
Yellow Stripe
7.94
[5/16]
8.73
[11/32]
6.35
[1/4]
7.14
[9/32]
Natural with
Black Stripe
3.97
[5/32]
4.76
[3/16]
6.35
[1/4]
7.14
[9/32]
Black
Green
Orange
White
4.76
[3/16]
5.56
[7/32]
6.35
[1/4]
7.14
[9/32]
PIDG STRATO-THERM*
Terminals
5.16
5.95
6.35
[1/4]
7.14
[9/32]
[13/64] [15/64]
5.16 5.95
[13/64] [15/64]
6.35
[1/4]
7.14
[9/32]
PIDG FASTON*
Receptacles 641321-2
(.187 Series) and
4.76
[3/16]
5.56
[7/32]
6.35
[1/4]
7.14
[9/32]
26-24
Yellow
1
69877-2
641324-2 (.110 Series)
Figure 2 (Part 2 of 2)
Rev B
3 of 7
408-2423
3. DIE SELECTION AND INSTALLATION
Refer to Figure 2 and select a compatible die assembly for the terminal or splice, based on the wire size being
used.
Refer to the Customer Manual supplied with the machine for information concerning installation of dies in the
machine.
When installing Die Assembly 68116-1 in Machine 69875, the terminal extractor/finger guard assembly and the
clear plastic applicator guard must be moved out from the machine as follows:
1. Remove the terminal extractor/finger guard assembly holding screw.
2. Reinstall the extractor/finger assembly using the holding screw (part no. 25064-1) and six washers
(part no. 21055-7) provided with the die assembly.
3. Remove the clear plastic applicator (side) guard.
4. Reinstall the guard using the two (lower) holding screws (part no. 2-21002-2) and two spacers
(part no. 4-25272-6) provided with the die assembly.
4. CRIMPING PROCEDURE
1. Load the terminal or splice tape into the machine. Refer to the Customer Manual for tape loading
instructions.
2. Strip the wire to the dimension specified in Figure 2. Do NOT cut or nick the wire.
NOTE
Depending on your wire stripping machine adjustment capabilities, the wire strip length may be increased to the nearest
0.79 mm [1/32 in.] if necessary.
3. Insert the prepared wire into the terminal or splice until the wire is bottomed.
DANGER
KEEP HANDS CLEAR OF DIES during the crimping procedure.
4. Hold the wire in position and activate the machine to crimp the terminal or splice.
5. Inspect the crimped product for a proper termination.
5. MAINTENANCE/INSPECTION
5.1. Daily Maintenance
It is recommended that a maintenance and inspection program be performed periodically to ensure dependable
and uniform terminations.
Frequency of inspection depends on:
1. The care, amount of use, and handling of the dies.
2. The presence of abnormal amounts of dust and dirt.
3. The degree of operator skill.
4. Your own established standards.
The dies are inspected before being shipped; however, it is recommended that the dies be inspected
immediately upon arrival at your facility to ensure that no damage occurred during shipment.
Due to the precision design, it is important that no parts of these dies be interchanged except those
replacement parts listed in Section 6.
Rev B
4 of 7
408-2423
5.2. Daily Maintenance
1. Remove dust, moisture, and other contaminants with a clean brush, or a soft, lint-free cloth. Do NOT
use objects that could damage the dies.
2. When the dies are not in use, store them in a clean, dry area.
5.3. Periodic Inspection
Regular inspections should be performed by quality control personnel. A record of scheduled inspections
should remain with the dies and/or be supplied to supervisory personnel responsible for the dies. Though
recommendations call for at least one inspection a month, the inspection frequency should be based on the
amount of use, ambient working conditions, operator raining and skill, and established company standards.
The inspections should be performed in the following sequence:
Visual Inspection
1. Remove accumulated dirt, grease, and foreign matter by immersing the dies in a suitable commercial
degreaser that will not affect paint or plastic material.
2. Make sure all die holding components are in place. Refer to the parts list in Figure 4 if replacements
are necessary.
3. Check all bearing surfaces for wear. Remove and replace worn components.
4. Inspect the crimp sections for flattened, chipped, cracked, worn, or broken areas. If damage is
evident, the dies must be repaired before returning them to service. See Section 6, REPLACEMENT
AND REPAIR, for information on obtaining customer repair service.
Gaging the Wire Barrel Crimping Chamber
This inspection requires the use of a plug gage conforming to the dimensions shown in Figure 3. To gage
the crimping chamber, refer to Figure 3, and proceed as follows:
1. Remove traces of oil or dirt from the crimping chamber and plug gage.
2. Mate the dies until it is evident that they have bottomed.
3. Align the GO element with the crimping chamber. Push element straight into the chamber without
using force. The GO element must pass completely through the crimping chamber.
4. Check the crimping chamber with the NO-GO element in the same manner as Step 3. The NO-GO
element may start entry, but must not pass completely through the crimping chamber.
If the dies conform to the gage inspection, they are considered dimensionally correct. If not correct, refer
to Section 6, REPLACEMENT AND REPAIR, for information on obtaining customer repair service.
For additional information regarding the use of a plug gage, refer to Instruction Sheet 408-7424.
6. REPLACEMENT AND REPAIR
The parts listed in Figure 4 are customer-replaceable parts. A complete inventory can be stocked and
controlled to prevent lost time when replacement of parts is necessary.
Order replacement parts through your representative, or call 1-800-526-5142, or send a facsimile of your
purchase order to 1-717-986-7605, or write to:
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
Dies may also be returned for evaluation and repair. For die repair service, contact a TE Connectivity
Representative at 1-800-526-5136.
Rev B
5 of 7
408-2423
GO
DIA
NO-GO
DIA
Crimping
Chamber
Insulation Barrel
Crimper
Wire Barrel
Crimper
GO Element
NO-GO Element
GAGE DIMENSION
DIE ASSEMBLY NUMBER
GO Diameter
NO-GO Diameter
68116-1
68207-1
68208-1
69872
69873
69874
69877
69877-2
69878
69897
69935
69936
69937
69938
5.105 [.2010]
3.023 [.1190]
2.769 [.1090]
2.769 [.1090]
3.023 [.1190]
4.293 [.1690]
1.600 [.0630]
1.600 [.0630]
2.261 [.0890]
4.293 [.1690]
2.311 [.0910]
2.667 [.1050]
3.327 [.1310]
3.835 [.1510]
Figure 3
5.258 [.2070]
3.175 [.1250]
2.921 [.1150]
2.921 [.1150]
3.175 [.1250]
4.445 [.1750]
1.753 [.0690]
1.753 [.0690]
2.413 [.0950]
4.445 [.1750]
2.388 [.0940]
2.743 [.1080]
3.404 [.1340]
3.912 [.1540]
7. REVISION SUMMARY
Updated document to corporate requirements
Changed part number in “Insul Indenter” column in Figure 4
Rev B
6 of 7
408-2423
25.4 [1.00]
(Ref)
15.85 [.624]
(Ref)
1
5
8
2
57.53 [2.265]
(Ref)
3
9
6
10
4
7
Replacement Parts (Quantity is one per die Assembly, except for Item 8, Quantity for Item 8 is two.)
SPECIAL
SCREW
SADDLE
SCREW
SPECIAL
SCREW
INSUL
INDENTER
CURVED
WASHER
INSUL
ANVIL
RTNG
RING
SADDLE
INDENTER
ANVIL
DIE ASSY
NO.
1
2
3
4
5
6
7
8
9
10
68116-1▪
68207-1
68208-1
69872
1-59781-4
2-59781-4
2-59781-4
3-59781-4
2-59781-4
59781-1
3-59577-8
1-59577-5
2-59577-9
2-59577-9
2-59577-9
2-59577-8
2-59577-7
2-59577-7
3-59577-0
2-59577-8
2-59577-7
2-59577-9
2-59577-9
2-59577-9
1-307275-7
1-307275-0
307275-9
307275-9
307275-9
1-307275-0
307275-9
307275-9
1-307275-1
1-307275-0
1-307275-5
307275-9
1-307275-6
1-307275-6
2-59781-5
2-59781-6
59781-6
59781-6
59781-6
59781-5
59781-7
59781-7
59781-8
59781-5
1-59781-8
59781-6
59781-6
59781-6
307913-1
307276-1
307285-2
307285-1
307285-2
307276-1
307285-3
307285-3
307285-4
307276-2
310676-3
310676-4
310676-5
310676-1
24088-8
24088-8
24088-8
24088-8
24088-8
24088-8
24088-8
24088-8
24088-8
24088-8
24088-8
24088-8
24088-8
24088-8
308916-1
1-21046-3
307914-1
59779-3
59779-2
59779-2
59779-3
310454-1
59782-2
59782-2
59782-8
310454-1
310674-2
310674-3
310674-4
310674-1
307915-1
59623-5
59623-6
59623-6
59623-5
59623-4
2-59615-0
2-59615-0
3-59615-0
59623-4
310675-2
310675-3
310675-4
310675-1
1-59619-2 1-21046-3
1-59619-8 1-21046-3
1-59619-7 1-21046-3
1-59619-8 1-21046-3
1-59619-2 1-21046-3
1-59619-5 1-21046-3
1-59619-5 1-21046-3
1-59619-4 1-21046-3
69873
69874
69877
59781-4
69877-2
69878
59781-4
59781-3
69897
59781-1
904765-1
310667-2
310667-3
310667-4
310667-1
1-21046-3
1-21046-3
1-21046-3
1-21046-3
1-21046-3
69935
1-59781-7
59781-2
69936
69937
2-59781-0
2-59781-0
69938
▪Refer to Section 3 for hardware to adapt guards.
Figure 4
Rev B
7 of 7
相关型号:
1-307275-7
Application and Maintenance for Crimping Die Assemblies for Tape-Mounted PIDG and PLASTI-GRIP Terminals and Splices
TE
1-307585-3
Crimping Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts
MACOM
1-307585-4
Crimping Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts
MACOM
1-307585-5
Crimping Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts
MACOM
1-307585-6
Crimping Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts
MACOM
1-307585-7
Crimping Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts
MACOM
1-307586-3
Crimping Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts
MACOM
1-307586-4
Crimping Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts
MACOM
1-307586-5
Crimping Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts
MACOM
1-307586-6
Crimping Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts
MACOM
1-307586-7
Crimping Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts
MACOM
©2020 ICPDF网 联系我们和版权申明