312145-1 [TE]

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools.;


型号：	312145-1
厂家：	TE CONNECTIVITY
描述：	Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools.
文件：	总3页 (文件大小：306K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Instruction Sheet

Pistol Grip Manual Handle Assembly

58074-1

408-6790

28 MAR 11 Rev C

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use

and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

For details concerning the termination procedure,

refer to the instructions included with the head.

NOTE

Key (Visible on

this Side)

Body

Ratchet

Pawl

3. HEAD INSTALLATION AND REMOVAL

1. Position the blade tip of a screwdriver between

the shoulder of the key and the handle assembly

body. Pry and remove the key.

2. Squeeze the cam handle until the ratchet

releases, then allow it to FULLY open.

3. Insert the terminating head into the head

entrance until the head bottoms. See Figure 2.

Make sure that the head is FULLY bottomed in the

handle assembly before re-inserting the key.

NOTE

Cam

Handle

Head

Figure 1

1. INTRODUCTION

Pistol Grip Manual Handle Assembly 58074-1 accepts

interchangeable terminating heads that terminate

wires to connectors. To ensure accurate termination of

wires, setup adjustments, and head maintenance,

refer to the instructions packaged with the terminating

head.

Head Entrance

Key Removed

Dimensions in this instruction sheet are in metric

units [with U.S. customary units in brackets].

NOTE

Figures are not drawn to scale.

Reasons for reissue of this instruction sheet are

provided in Section 6, REVISION SUMMARY.

Cam Handle Fully Opened

2. DESCRIPTION

The manual handle assembly features a cam handle,

a key, and a ratchet pawl. The head is secured in the

handle assembly with the key.

Figure 2

4. Re-insert the key to retain the head. Apply

enough pressure to fully insert the key into the

manual assembly.

After the head is properly installed in the handle

assembly, the cam handle actuates the terminating

mechanism inside the head. The ratchet pawl is used

to release the handle before it is fully closed.

5. To remove the head, remove the key and pull the

head out of the handle assembly.

1 of 3

PRODUCT INFORMATION 1-800-522-6752

For latest revision and Regional Customer Service,

visit our website at www.te.com

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks.

LOC B

*Trademark. Other logos, product and/or Company names may be trademarks of their respective owners.

408-6790

4. MAINTENANCE AND INSPECTION

4.2. Periodic Inspection

It is recommended that a maintenance and inspection

program be performed periodically to ensure

dependable and uniform terminations. Though

recommendations call for at least one inspection a

month, frequency of inspection depends on:

1. Remove any accumulated film with a suitable

cleaning agent that will not affect plastic material.

2. Make sure all components are in place and are

properly secured. Check the handle assembly for

chipped, cracked, worn, or broken areas. If damage

is evident, repair is necessary. See Section 6,

REPLACEMENT AND REPAIR.

1. The care, amount of use, and handling of the

handle assembly.

2. The presence of abnormal amounts of dust and

dirt.

5. REPLACEMENT AND REPAIR

Customer-replaceable parts are listed in Figure 3.

3. The degree of operator skill.

A complete inventory can be stocked and controlled to

prevent lost time when replacement of parts is

necessary. Parts other than those listed should be

replaced by Tyco Electronics Corporation to ensure

quality and reliability of the handle assembly. Order

replacement parts through your representative, or call

1-800-526-5142, or send a facsimile of your purchase

to 717-986-7605, or write to:

4. Your own established standards.

The handle assembly is inspected before being

shipped; however, it is recommended that the handle

assembly be inspected immediately upon arrival to

ensure that the handle assembly has not been

damaged during shipment.

4.1. Daily Maintenance

CUSTOMER SERVICE (038-035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

Each operator should be aware of, and responsible

for, the following:

1. Remove dust, moisture, and other contaminants

with a clean brush, or soft, lint-free cloth. DO NOT

use objects that could damage the handle

assembly.

HARRISBURG PA 17105-3608

For customer repair service, call 1-800-526-5136.

6. REVISION SUMMARY

2. Ensure that all components are in place and

properly secured.

Since the previous release of this instruction sheet,

the new company logo has been applied.

3. With the terminating head in place, squeeze and

release the cam handle to ensure that the

mechanisms move smoothly.

4. Depress and release the spring-loaded ratchet

pawl to ensure that the pawl moves freely.

5. Check the extension springs to ensure they are

properly located and are not deformed.

2 of 3

Rev C

408-6790

REPLACEMENT PARTS

ITEM

PART NUMBER

312145-1

1-22353-2

312140-1

312141-1

312142-1

28593-1

DESCRIPTION

QTY PER ASSY

HANDLE, Cam

SCREW, Slot Head Shoulder

KEY

NUT, Cam Adjustment

SCREW, Ratchet Adjustment

SCREW, Self-Tapping

PIN, Dowel

1-21919-2

312143-1

22286-9

PAWL, Ratchet

SPRING, Extension

HANDLE, Right

312144-1

312144-2

28593-3

HANDLE, Left

SCREW, Self-Tapping, .22 X .62 In. L

Figure 3

3 of 3

Rev C

相关型号：