2215035-2
更新时间:2024-09-18 22:16:38
品牌:TE
描述:Read and understand these instructions before using the removal tools.
2215035-2 概述
Read and understand these instructions before using the removal tools.
2215035-2 数据手册
通过下载2215035-2数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载Instruction Sheet
Removal Kits 2215035-[ ]
for STRADA Whisper* Headers
408-32224
11 DEC 15 Rev A
Removal Knob
Clamp
Subassembly
Wedge
Block
Swage
Screws
Pusher
Block
Swage
Subassembly
Clamp
Screws
Swage Block
REMOVAL KIT NUMBER
WILL REMOVE
6 Pair x 3 Col Headers
Figure 1
PRODUCT PART NUMBERS
2215035-1
2215035-2
2187541-1
1. INTRODUCTION
Removal Kits 2215035-[ ] are designed to remove STRADA Whisper Headers from printed circuit (pc) boards.
Refer to Figure 1.
Read and understand these instructions before using the removal tools.
NOTE
Dimensions on this sheet are in metric units [with U.S. customary units in brackets]. Figures and illustrations are for reference
only and are not drawn to scale.
2. DESCRIPTION
Each kit consists of two swage subassemblies, one clamp subassembly, one pusher block, on removal knob,
and two separation screws. The swage subassemblies consists of a swage block, a wedge block, and two
swage screws. The clamp subassembly consists of two side clamp blocks and two clamp screws.
The swage subassemblies grip the header by swaging the tops of the header c-pins. The clamp subassembly
grips the sides of the header to allow the swage subassembly to provide the swaging action. As a user tightens
the removal knob on the pusher block, the swage subassembly is pulled away from the pc board. The
separation screws allow a user to remove the header from the swage block after removal from the pc board.
3. OPERATION
3.1. Tool Preparation
To prepare the removal tool, first determine the dimensions of the header, (number of rows and columns). To
prepare the tool:
1. Select the kit part number to be used based on the header number or size.
2. Select the proper swage subassembly for the receptacle part number or size.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com.
© 2015 TE Connectivity family of companies
All Rights Reserved
*Trademark
PRODUCT INFORMATION 1-800-522-6752
1 of 4
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
408-32224
3.2. Removal Procedure
CAUTION
Be certain the removal tool does not contact any pc board components except the header to be removed during use.
1. Remove or straighten any header components that may interfere with the swage block.
2. Loosen the swage screws to separate the swage block and the wedge block.
3. Place the swage block onto the header to be removed. Orient the swage block as shown in Figure 2.
Orientation Mark
Header
Alignment Mark
PC Board
Swage Block
Figure 2
4. Place the wedge block onto the swage block and insert the swage screws into the wedge block. Do
not tighten the swage screws. Orient the wedge block as shown in Figure 3.
Swage Screws
Wedge Block
Alignment Mark
Figure 3
5. Loosen the clamp screws on the clamp subassembly and place the clamp subassembly over the
swage subassembly.
6. Make sure the swage block is fully inserted into the header and tighten the clamp screws. The
recommended torque for the clamp screws is 2 N-m [18 in.-lbs]. See Figure 4.
7. Tighten the swage screws. Tighten the screws at the same rate. Do not tighten one more than half of
a turn before tightening the other by the same amount. The recommended torque for the swage
screws is 2 N-m [18 in.-lbs].
8. Loosen the clamp screws and remove the clamp subassembly. Do not loosen the swage screws.
2 of 4
Rev A
408-32224
Clamp
Subassembly
Swage Block Fully
Clamp Screws
Inserted into Header
Figure 4
9. Place the pusher block over the swage subassembly and place the removal knob in the pusher block
as shown in Figure 5.
Removal Knob
Pusher Block
Figure 5
10. Tighten the removal knob to remove the header from the pc board.
CAUTION
The tool and header can spin after removal due to the twisting action of the removal knob. This spin could cause damage to
the pc board. Hold the tool firmly during removal.
DANGER
The pins on the bottom of the header can be very sharp. Exercise caution when handling a removed header.
11. Remove any remaining components from the pc board.
12. Loosen the removal knob and remove the removal knob and pusher block from the swage
subassembly.
13. Loosen the swage screws to remove the wedge block from the swage block. The swage screws can
be stored in the swage screw holding taps on the pusher block. See Figure 5.
14. Separate the header from the swage block. If the header is not easily removed from the swage block,
see Paragraph 3.3, Separation Procedure.
3.3. Separation Procedure
The swaging action may cause the header to become stuck on the swage block. To remove the header from
the swage block, perform the following procedure:
1. Remove the separation screws and washers from the pusher block.
3 of 4
Rev A
408-32224
2. Place the pusher block over the swage block and header.
3. Make sure the washers are on the separation screws and thread the screws into the swage block as
shown in Figure 6.
4. Tighten the separation screws. Tighten the screws at the same rate. Do not tighten one more than half
of a turn before tightening the other by the same amount.
5. When the header is removed from the swage block, loosen the separation screws and place them into
the pusher block as shown in Figure 1.
Separation
Screws
Swage Block
Pusher Block
Header
Figure 6
4. MAINTENANCE AND INSPECTION
TE Connectivity (TE) recommends that the tool be inspected immediately upon its arrival to ensure that it has
not been damaged during shipment.
4.1. Daily Maintenance
It is recommended that each operator be made aware of, and responsible for, the following steps of daily
maintenance:
Remove dust, moisture, and other contaminants with a clean, soft brush, or lint-free cloth. DO NOT use
objects that could damage the tool or any of its components.
When the tool is not in use, store it in a clean, dry area.
4.2. Periodic Inspection
Regular inspections should be performed by quality control personnel. A record of scheduled inspections
should remain with the tool or be supplied to personnel responsible for the tool. The inspection frequency
should be based on the amount of use, working conditions, operator training and skill, and established
company standards.
5. REPLACEMENT AND REPAIR
Parts should be replaced by TE to ensure quality and reliability. For customer repair service or to order
replacement parts, call 1-800-522-6752, or fax your purchase order to 717-986-7605, or write to: Customer
Service (038-035), Tyco Electronics Corporation, PO Box 3608, Harrisburg, PA 17105-3608.
6. REVISION SUMMARY
Initial release of document
4 of 4
Rev A
2215035-2 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
2215042-1 | TE | Removal Kits 2215042 for STRADA-Whisper Receptacles | 获取价格 | |
2215042-2 | TE | Removal Kits 2215042 for STRADA-Whisper Receptacles | 获取价格 | |
2215058-1 | TE | Enhanced Small Form-Factor | 获取价格 | |
2215058-2 | TE | Enhanced Small Form-Factor | 获取价格 | |
2215058-3 | TE | Enhanced Small Form-Factor | 获取价格 | |
2215058-4 | TE | Enhanced Small Form-Factor | 获取价格 | |
2215058-5 | TE | Enhanced Small Form-Factor | 获取价格 | |
2215058-6 | TE | Enhanced Small Form-Factor | 获取价格 | |
2215059-1 | TE | Enhanced Small Form-Factor | 获取价格 | |
2215059-2 | TE | Enhanced Small Form-Factor | 获取价格 |
2215035-2 相关文章
- 2024-09-20
- 5
- 2024-09-20
- 8
- 2024-09-20
- 8
- 2024-09-20
- 6