首页 |元器件品牌

VLP8040T-100M_16 [TDK]

Wound Ferrite;
VLP8040T-100M_16
型号： VLP8040T-100M_16
厂家： TDK ELECTRONICS    TDK ELECTRONICS
描述：

Wound Ferrite
文件： 总9页 (文件大小：183K)
中文：  中文翻译
下载：  下载PDF数据表文档文件
 查看货源
I
N
D
U
C
T
O
R
S
January 2016  
Inductors for Power Circuits  
Wound Ferrite  
VLP Series  
VLP8040 Type  
VLP8040  
＊
(2/9)  
I
N
D
U
C
T
O
R
S
REMINDERS FOR USING THESE PRODUCTS  
Before using these products, be sure to request the delivery specifications.  
SAFETY REMINDERS  
Please pay sufficient attention to the warnings for safe designing when using these products.  
REMINDERS  
The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or  
less).  
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.  
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).  
Before soldering, be sure to preheat components.  
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature  
does not exceed 150°C.  
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.  
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.  
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to  
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.  
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal  
design.  
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.  
A malfunction may occur due to magnetic interference.  
Use a wrist band to discharge static electricity in your body through the grounding wire.  
Do not expose the products to magnets or magnetic fields.  
Do not use for a purpose outside of the contents regulated in the delivery specifications.  
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications  
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement  
equipment, industrial robots) under a normal operation and use condition.  
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or  
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to  
society, person or property.  
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions  
set forth in the each catalog, please contact us.  
(1) Aerospace/Aviation equipment  
(2) Transportation equipment (cars, electric trains, ships, etc.)  
(3) Medical equipment  
(8) Public information-processing equipment  
(9) Military equipment  
(10) Electric heating apparatus, burning equipment  
(11) Disaster prevention/crime prevention equipment  
(12) Safety equipment  
(4) Power-generation control equipment  
(5) Atomic energy-related equipment  
(6) Seabed equipment  
(13) Other applications that are not considered general-purpose  
applications  
(7) Transportation control equipment  
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing  
protection circuit/device or providing backup circuits in your equipment.  
＊
20160128 / inductor_commercial_power_vlp8040_en.
(3/9)  
I
N
D
U
C
T
O
R
S
Product compatible with RoHS directive  
Halogen-free  
Inductors for Power Circuits  
Wound Ferrite  
Compatible with lead-free solders  
Overview of VLP8040 Type  
FEATURES  
Magnetic shield type wound inductor for power circuits.  
Magnetic shield construction with ferrite resin material.  
APPLICATION  
Thin-screen TVs, printers, laptop computers, other  
PART NUMBER CONSTRUCTION  
VLP  
8040  
L
T
-
1R0  
N
L×W×H Dimensions  
(mm max.)  
Inductance  
(μH)  
Inductance  
tolerance  
Series name  
internal code  
Packaging style  
8040  
8.6×8.7×4.0  
T
Taping  
1R0  
100  
101  
1.0  
10  
100  
M
N
20%  
30%  
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT  
Temperature range  
Package quantity  
Individual weight  
Operating Storage  
Type  
ꢀ
ꢀꢀ  
temperature  
temperature  
(pieces/reel)  
（°C）  
（°C）  
（mg）  
VLP8040  
–40 to +105  
–40 to +105  
1000  
840  
ꢀꢁ  
Operating temperature range includes self-temperature rise.  
The Storage temperature range is for after the circuit board is mounted.  
ꢀꢀꢁ  
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/  
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.  
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.  
Please note that the contents may change without any prior notice due to reasons such as upgrading.  
＊
20160128 / inductor_commercial_power_vlp8040_en.
(4/9)  
I
N
D
U
C
T
O
R
S
VLP8040 Type  
RECOMMENDED REFLOW PROFILE  
Preheating  
Soldering  
Natural  
cooling  
Peak  
T4  
T3  
T3  
T2  
t3  
t2  
T1  
t1  
t: Time  
Preheating  
Temp.  
T1  
Soldering  
Temp.  
T3  
Peak  
Temp.  
T4  
Time  
t1  
60 to 120s  
Time  
t2  
40s  
Time  
t3  
5s  
T2  
180°C  
150°C  
220°C  
260°C  
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.  
Please note that the contents may change without any prior notice due to reasons such as upgrading.  
＊
20160128 / inductor_commercial_power_vlp8040_en.
(5/9)  
I
N
D
U
C
T
O
R
S
VLP8040 Type  
SHAPE & DIMENSIONS  
8.6max.  
2.675  
1.6  
2.675  
Dimensions in mm  
RECOMMENDED LAND PATTERN  
3.3  
1.4  
3.3  
Dimensions in mm  
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.  
Please note that the contents may change without any prior notice due to reasons such as upgrading.  
＊
20160128 / inductor_commercial_power_vlp8040_en.
(6/9)  
I
N
D
U
C
T
O
R
S
VLP8040 Type  
ELECTRICAL CHARACTERISTICS  
CHARACTERISTICS SPECIFICATION TABLE  
Rated currentꢀ  
L
Measuring  
frequency  
DC resistance  
Part No.  
Idc1  
(A)max.  
9.4  
7.8  
6.7  
5.2  
4.4  
3.6  
3.2  
2.6  
2.2  
1.8  
1.5  
1.2  
1.0  
0.8  
0.6  
Idc2  
(A)typ.  
7.0  
6.7  
6.2  
5.2  
4.5  
4.0  
3.5  
2.9  
2.5  
2.1  
1.7  
1.4  
1.2  
1.0  
0.8  
0.7  
0.5  
(μH)  
1.0  
Tolerance  
30%  
30%  
30%  
30%  
20%  
20%  
20%  
20%  
20%  
20%  
20%  
20%  
20%  
20%  
20%  
20%  
20%  
(kHz)  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
(ꢂ )max.  
0.011  
0.013  
0.015  
0.020  
0.025  
0.032  
0.038  
0.058  
0.075  
0.11  
0.16  
0.23  
0.33  
0.49  
0.73  
1.1  
2.2  
(ꢂ )typ.  
0.008  
0.010  
0.012  
0.015  
0.019  
0.024  
0.032  
0.048  
0.062  
0.090  
0.13  
0.19  
0.28  
0.41  
0.61  
0.89  
1.8  
VLP8040T-1R0N  
VLP8040T-1R5N  
VLP8040T-2R2N  
VLP8040T-3R3N  
VLP8040T-4R7M  
VLP8040T-6R8M  
VLP8040T-100M  
VLP8040T-150M  
VLP8040T-220M  
VLP8040T-330M  
VLP8040T-470M  
VLP8040T-680M  
VLP8040T-101M  
VLP8040T-151M  
VLP8040T-221M  
VLP8040T-331M  
VLP8040T-681M  
1.5  
2.2  
3.3  
4.7  
6.8  
10  
15  
22  
33  
47  
68  
100  
150  
220  
330  
680  
0.5  
0.3  
ꢀꢁ Rated current: smaller value of either Idc1 or Idc2.  
Idc1: When based on the inductance change rate (30% below the initial value)  
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)  
○ Measurement equipment  
Measurement item  
Product No.  
Manufacturer  
L
4194A  
VP-2941A  
4285A+42841A+42842C  
Agilent Technologies  
Panasonic  
Agilent Technologies  
DC resistance  
Rated current Idc1  
＊ Equivalent measurement equipment may be used.  
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.  
Please note that the contents may change without any prior notice due to reasons such as upgrading.  
＊
20160128 / inductor_commercial_power_vlp8040_en.
(7/9)  
I
N
D
U
C
T
O
R
S
VLP8040 Type  
ELECTRICAL CHARACTERISTICS  
L FREQUENCY CHARACTERISTICS GRAPH  
10000  
1000  
100  
10  
681M  
331M  
151M  
221M  
101M  
680M  
470M  
330M  
220M  
150M  
100M  
6R8M  
4R7M  
3R3N  
2R2N  
1R5N  
1R0N  
1
0.1  
0.01  
0.1  
1
10  
100  
(
)
Frequency MHz  
○ Measurement equipment  
Product No.  
Manufacturer  
4294A  
Agilent Technologies  
＊ Equivalent measurement equipment may be used.  
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.  
Please note that the contents may change without any prior notice due to reasons such as upgrading.  
＊
20160128 / inductor_commercial_power_vlp8040_en.
(8/9)  
I
N
D
U
C
T
O
R
S
VLP8040 Type  
ELECTRICAL CHARACTERISTICS  
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH  
1000  
681M  
331M  
221M  
151M  
100  
101M  
680M  
470M  
330M  
220M  
150M  
10  
100M  
6R8M  
4R7M  
3R3N  
2R2N  
1R5N  
1
1R0N  
0.1  
0.0  
2.0  
4.0  
6.0  
8.0  
10.0  
12.0  
14.0  
16.0  
18.0  
DC current(A)  
○ Measurement equipment  
Product No.  
4285A+42841A+42842C  
Manufacturer  
Agilent Technologies  
＊ Equivalent measurement equipment may be used.  
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.  
Please note that the contents may change without any prior notice due to reasons such as upgrading.  
＊
20160128 / inductor_commercial_power_vlp8040_en.
(9/9)  
I
N
D
U
C
T
O
R
S
VLP8040 Type  
PACKAGING STYLE  
REEL DIMENSIONS  
2.0 0.5  
E
Type  
VLP8040  
A
ø330  
W1  
16.4  
W2  
22.4  
N
ø100  
E
2
* These values are typical values.  
(
)
1.0  
ø13.0 0.5  
ø21.0 0.8  
W1  
W2  
A
Dimensions in mm  
TAPE DIMENSIONS  
øD0  
P2  
P0  
P1  
K
t
Dimensions in mm  
A
Type  
A
B
øD0  
E
F
P0  
P1  
P2  
W
K
t
VLP8040 8.8  
8.0  
1.5+0.1/-0 1.75 0.1 7.5 0.1 4.0 0.1 12.0 0.1 2.0 0.1 16.0 0.3 4.3  
0.4  
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.  
Please note that the contents may change without any prior notice due to reasons such as upgrading.  
＊
20160128 / inductor_commercial_power_vlp8040_en.

相关型号：

VLP8040T-101M

 General Purpose Inductor, 100uH, 20%, 1 Element, Ferrite-Core, SMD, 3432, HALOGEN FREE AND ROHS COMPLIANT
TDK

VLP8040T-150M

 General Purpose Inductor, 15uH, 20%, 1 Element, Ferrite-Core, SMD, 3432, HALOGEN FREE AND ROHS COMPLIANT
TDK

VLP8040T-151M

 General Purpose Inductor, 150uH, 20%, 1 Element, Ferrite-Core, SMD, 3432, HALOGEN FREE AND ROHS COMPLIANT
TDK

VLP8040T-1R0N

 General Purpose Inductor, 1uH, 30%, 1 Element, Ferrite-Core, SMD, 3432, HALOGEN FREE AND ROHS COMPLIANT
TDK

VLP8040T-1R5N

 General Purpose Inductor, 1.5uH, 30%, 1 Element, Ferrite-Core, SMD, 3432, HALOGEN FREE AND ROHS COMPLIANT
TDK

VLP8040T-220M

 General Purpose Inductor, 22uH, 20%, 1 Element, Ferrite-Core, SMD, 3432, HALOGEN FREE AND ROHS COMPLIANT
TDK

VLP8040T-221M

 Inductors for Power Circuits Wound Ferrite
TDK

VLP8040T-2R2N

 General Purpose Inductor, 2.2uH, 30%, 1 Element, Ferrite-Core, SMD, 3432, HALOGEN FREE AND ROHS COMPLIANT
TDK

VLP8040T-330M

 General Purpose Inductor, 33uH, 20%, 1 Element, Ferrite-Core, SMD, 3432, HALOGEN FREE AND ROHS COMPLIANT
TDK

VLP8040T-331M

 General Purpose Inductor, 330uH, 20%, 1 Element, Ferrite-Core, SMD, 3432, HALOGEN FREE AND ROHS COMPLIANT
TDK

VLP8040T-3R3N

 General Purpose Inductor, 3.3uH, 30%, 1 Element, Ferrite-Core, SMD, 3432, HALOGEN FREE AND ROHS COMPLIANT
TDK

VLP8040T-470M

 General Purpose Inductor, 47uH, 20%, 1 Element, Ferrite-Core, SMD, 3432, HALOGEN FREE AND ROHS COMPLIANT
TDK
©2020 ICPDF网 联系我们和版权申明