VLCF4020T-101MR26_16 [TDK]
Wound Ferrite;型号: | VLCF4020T-101MR26_16 |
厂家: | TDK ELECTRONICS |
描述: | Wound Ferrite |
文件: | 总9页 (文件大小:112K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
I
N
D
U
C
T
O
R
S
April 2016
Inductors for Power Circuits
Wound Ferrite
VLCF Series
VLCF4020 Type
VLCF4020
(2/9)
I
N
D
U
C
T
O
R
S
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or
less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(13) Other applications that are not considered general-purpose
applications
(7) Transportation control equipment
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
20160411 / inductor_commercial_power_vlcf4020_en.
(3/9)
I
N
D
U
C
T
O
R
S
Product compatible with RoHS directive
Halogen-free
Inductors for Power Circuits
Wound Ferrite
Compatible with lead-free solders
Overview of VLCF4020 Type
FEATURES
Magnetic shield type wound inductor for power circuits.
Low-profile product.
Magnetic shield construction with ferrite core.
APPLICATION
Power source inductor for mobile devices such as HDDs, DVCs, and DSCs
LCDs, other DC to DC converters
PART NUMBER CONSTRUCTION
VLCF
4020
T
-
1R8
N
1R9
-
2
L×W×H Dimensions
(mm)
Inductance
(μH)
Rated current
(A)
Inductance
tolerance
Series name
Packaging style
Internal code
4020
4.0×4.0×2.0
T
Taping
1R8
150
101
1.8
15
100
M
N
20%
30%
1R9
150
101
1.9
15
100
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Package quantity
Individual weight
Operating Storage
Type
ꢀ
ꢀꢀ
temperature
temperature
(pieces/reel)
(°C)
(°C)
(mg)
VLCF4020
–40 to +105
–40 to +105
1000
112
ꢀꢁ
Operating temperature range includes self-temperature rise.
The Storage temperature range is for after the circuit board is mounted.
ꢀꢀꢁ
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_vlcf4020_en.
(4/9)
I
N
D
U
C
T
O
R
S
VLCF4020 Type
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T4
T3
T3
T2
t3
t2
T1
t1
t: Time
Preheating
Temp.
T1
Soldering
Temp.
T3
Peak
Temp.
T4
Time
t1
110s
Time
t2
90s
Time
t3
5s
T2
150°C
130°C
200°C
260°C
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_vlcf4020_en.
(5/9)
I
N
D
U
C
T
O
R
S
VLCF4020 Type
SHAPE & DIMENSIONS
4.0 0.1
4R7
2
Dimensions in mm
RECOMMENDED LAND PATTERN
2.5
45°
3.9
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_vlcf4020_en.
(6/9)
I
N
D
U
C
T
O
R
S
VLCF4020 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated currentꢀ
L
Measuring
frequency
DC resistance
Part No.
Isat
Itemp
(A)typ.
2.37
2.19
1.94
1.71
1.47
1.22
1.0
0.8
0.8
0.69
0.56
0.45
(μH)
1.8
2.2
3.3
4.7
6.8
10
15
22
27
33
Tolerance
30%
30%
30%
30%
30%
20%
20%
20%
20%
20%
20%
20%
(kHz)
100
100
100
100
100
100
100
100
100
100
100
100
(ꢂ )max.
0.051
0.059
0.078
0.098
0.131
0.185
0.303
0.431
0.496
0.628
0.934
1.4
(ꢂ )typ.
0.046
0.054
0.071
0.089
0.119
0.168
0.275
0.391
0.451
0.571
0.849
1.308
(A)max.
1.97
1.72
1.52
1.24
1.05
0.85
0.68
0.56
0.48
0.47
0.39
0.26
VLCF4020T-1R8N1R9
VLCF4020T-2R2N1R7
VLCF4020T-3R3N1R5
VLCF4020T-4R7N1R2
VLCF4020T-6R8N1R0
VLCF4020T-100MR85
VLCF4020T-150MR68
VLCF4020T-220MR56
VLCF4020T-270MR48
VLCF4020T-330MR47
VLCF4020T-470MR39
VLCF4020T-101MR26
47
100
ꢀꢁ Rated current: smaller value of either Isat or Itemp.
Isat: When based on the inductance change rate (30% below the initial value)
Itemp: When based on the temperature increase (Temperature increase of 40°C by self heating)
○ Measurement equipment
Measurement item
Product No.
Manufacturer
L
4194A
VP-2941A
4285A+42841A+42842C
Keysight Technologies
Panasonic
Keysight Technologies
DC resistance
Rated current Isat
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_vlcf4020_en.
(7/9)
I
N
D
U
C
T
O
R
S
VLCF4020 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
1000
100
10
101M
470M
330M
270M
220M
150M
100M
6R8N
4R7N
3R3N
2R2N
1R8N
1
0.1
0.01
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A
Keysight Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_vlcf4020_en.
(8/9)
I
N
D
U
C
T
O
R
S
VLCF4020 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
1000
101M
100
470M
330M
270M
220M
150M
10
100M
6R8N
4R7N
3R3N
2R2N
1R8N
1
0.1
0.0
1.0
2.0
3.0
4.0
5.0
( )
DC current A
○ Measurement equipment
Product No.
4285A+42841A+42842C
Manufacturer
Keysight Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_vlcf4020_en.
(9/9)
I
N
D
U
C
T
O
R
S
VLCF4020 Type
PACKAGING STYLE
REEL DIMENSIONS
2.0 0.5
E
Type
VLCF4020
A
ø180
W1
13
W2
17
N
ø60
E
0.5
* These values are typical values.
(
)
1.0
ø13.0 0.5
ø21.0 0.8
W1
W2
A
Dimensions in mm
TAPE DIMENSIONS
øD0
P2
P0
P1
K
t
Dimensions in mm
A
Type
A
B
øD0
E
F
P0
P1
P2
W
K
t
VLCF4020 4.2
4.2
1.55 0.05 1.75 0.1 5.5 0.1 4.0 0.1 8.0 0.1 2.00 0.05 12.0 0.2 2.2
0.3
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_vlcf4020_en.
相关型号:
VLCF4020T-2R2N1R7
High-Integration, High-Efficiency Power Solution Using DC/DC Converters With DVFS
TI
©2020 ICPDF网 联系我们和版权申明