KPZ1608SHR121ATDH5 [TDK]
Ferrite Chip,;
| 型号： | KPZ1608SHR121ATDH5 |
| 厂家： | 
TDK ELECTRONICS |
| 描述： | Ferrite Chip, |
| 文件： | 总10页 (文件大小：196K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
E M C C o m p o n e n t s
March 2017
Chip beads
For power line
Soft termination
KPZ-HR series (for automobiles)
KPZ1608-HRtype
KPZ1608-HR
1608[0603 inch]*
* Dimensions code JIS[EIA]
(2/10)
E M C C o m p o n e n t s
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (electric trains, ships, etc.)
(3) Medical equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(13) Other applications that are not considered general-purpose
applications
(7) Transportation control equipment
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
20170315 / beads_automotive_power_kpz1608-hr_en.
(3/10)
E M C C o m p o n e n t s
Product compatible with RoHS directive
Halogen-free
Chip beads
For power line
Compatible with lead-free solders
AEC-Q200
Soft termination
Overview of KPZ1608-HR type
FEATURES
Noise reduction solution for power line.
Compared to the KMZ series, has low direct current resistance for compatibility with large currents, optimal for low power consumption.
Guide electric property resin absorbs external stress, and mechanical stress, resistance force to thermal shock is improved.
Easing by conductive resin thermal stress, and respond for High-temperature environment of 150 °C, too.
APPLICATION
Various ECUs, powertrains, body controls, and car multimedia (telematics).
PART NUMBER CONSTRUCTION
KPZ
1608
S
HR
121
A
T
DH5
L×W×T dimensions
(mm)
Impedance
() at 100MHz
Material
name
Specifications
(Grade)
Characteristic
type
Internal
code
Series name
Packaging style
Soft
termination
1.6×0.8x0.6
1608
S
HR
121
601
120
600
A
T
Taping
DH5
D25
1.6×0.8x0.8
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Package quantity
Individual weight
Operating
temperature
Storage
temperature*
Type
(pieces/reel)
（mg）
（°C）
（°C）
t=0.6mm (DH5)
t=0.8mm (D25)
–55 to +150
–55 to +150
–55 to +150
–55 to +150
4,000
4,000
3
4
KPZ1608-HR
The storage temperature range is for after the circuit board is mounted.
RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20170315 / beads_automotive_power_kpz1608-hr_en.
(4/10)
E M C C o m p o n e n t s
KPZ1608-HR type
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T4
T3
T3
T2
t3
t2
T1
t1
t: Time
Preheating
Temp.
T1
Soldering
Temp.
T3
Peak
Temp.
T4
Time
t1
60 to 120s
Time
t2
30 to 60s
Time
t3
10s
T2
180°C
150°C
230°C
250 to 260°C
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20170315 / beads_automotive_power_kpz1608-hr_en.
(5/10)
E M C C o m p o n e n t s
KPZ1608-HR type
MATERIAL CHARACTERISTIC
S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in
which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz.
TYPICAL MATERIAL IMPEDANCE CHARACTERISTICSꢀ
2500
2000
1500
1000
S
500
0
10
100
1000
Frequency(MHz)
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20170315 / beads_automotive_power_kpz1608-hr_en.
(6/10)
E M C C o m p o n e n t s
KPZ1608-HR type
SHAPE & DIMENSIONS
1.6 0.15
( )
Thickness T
0.6 0.15mm
0.8 0.15mm
0.3 0.2
Dimensions in mm
RECOMMENDED LAND PATTERN
0.6
0.8
0.6
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20170315 / beads_automotive_power_kpz1608-hr_en.
(7/10)
E M C C o m p o n e n t s
KPZ1608-HR type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current
Impedance
DC resistance
Thickness T
Part No.
[100MHz]
()
30
Tolerance
10
25%
25%
25%
()max.
0.015
0.045
0.05
0.15
0.3
(A)max.
5.0
2.0
2.2
1
(mm)
0.6
0.6
0.8
0.8
KPZ1608SHR300ATDH5
KPZ1608SHR121ATDH5
KPZ1608SHR221ATD25
KPZ1608SHR601ATD25
KPZ1608SHR102ATD25
120
220
600
1000
25%
0.8
0.8
Please refer to the graph of rated current vs. temperature characteristics (derating) about the rating current at 85°C or more in temperature of the product.
○ Measurement equipment
Measurement item
Product No.
Manufacturer
Impedance
DC resistance
E4991A+16192A
Type-7556
Keysight Technologies
Yokogawa
＊ Equivalent measurement equipment may be used.
○ Rated current vs. temperature characteristics (derating)
6.0
5.0
SHR300A
4.0
3.0
SHR221A
2.0
SHR121A
SHR601A
1.0
SHR102A
0.0
–55
–25
5
35
65
95
125
150
(
)
Temperature °C
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20170315 / beads_automotive_power_kpz1608-hr_en.
(8/10)
E M C C o m p o n e n t s
KPZ1608-HR type
ELECTRICAL CHARACTERISTICS
Z VS. FREQUENCY CHARACTERISTICS (BY SERIES)
KPZ1608-SHR series
1200
KPZ1608SHR102A
1000
900
800
700
600
500
400
300
200
100
0
KPZ1608SHR221A
KPZ1608SHR601A
KPZ1608SHR121A
KPZ1608SHR300A
1
10
100
1000
)
10000
(
Frequency MHz
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20170315 / beads_automotive_power_kpz1608-hr_en.
(9/10)
E M C C o m p o n e n t s
KPZ1608-HR type
ELECTRICAL CHARACTERISTICS
Z, X, R VS. FREQUENCY CHARACTERISTICS
KPZ1608SHR300ATDH5
KPZ1608SHR121ATDH5
KPZ1608SHR221ATD25
200
150
100
50
300
40
35
30
250
200
25
Z
Z
R
Z
R
150
20
15
10
5
R
100
50
0
X
X
X
0
0
1
10
100
1000
)
10000
1
10
100
1000
( )
Frequency MHz
10000
1
10
100
1000
)
10000
(
(
Frequency MHz
Frequency MHz
KPZ1608SHR601ATD25
KPZ1608SHR102ATD25
1200
1000
800
800
700
600
500
400
300
200
100
0
Z
Z
R
R
600
400
200
X
X
(
0
1
10
100
1000
)
10000
1
10
100
1000
)
10000
(
Frequency MHz
Frequency MHz
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20170315 / beads_automotive_power_kpz1608-hr_en.
(10/10)
E M C C o m p o n e n t s
KPZ1608-HR type
PACKAGING STYLE
REEL DIMENSIONS
2.0 0.5
1.0
+2.0
–0.0
8.4
ø13 0.2
ø21 0.8
14.4max.
ø180 2.0
Dimensions in mm
TAPE DIMENSIONS
1.50+0.1
2.0 0.05
4.0 0.1
A
P1
K
Dimensions in mm
K
Type
KPZ1608-HR
A
B
1.9 0.2
P1
4.0 0.1
1.1 0.2
1.1max.
160min.
Taping
200min.
300min.
Drawing direction
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20170315 / beads_automotive_power_kpz1608-hr_en.
相关型号：
©2020 ICPDF网 联系我们和版权申明