PC29.09.0100A_17 [TAOGLAS]
TheStripe⢠Penta-band Cellular 850 / 900 / 1800 / 1900 UMTS / WCDMA (3G) 2100 MHz PCB Antenna;
| 型号： | PC29.09.0100A_17 |
| 厂家： | 
Taoglas |
| 描述： | TheStripe⢠Penta-band Cellular 850 / 900 / 1800 / 1900 UMTS / WCDMA (3G) 2100 MHz PCB Antenna PC CD |
| 文件： | 总11页 (文件大小：1084K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Specification
Part No.
:
:
PC29.09.0100A
Product Name
TheStripe™
Penta-band Cellular 850 / 900 / 1800 / 1900
UMTS / WCDMA (3G) 2100 MHz PCB Antenna
Feature
:
100mm long, 1.13 mm diameter
Miniature Co-axial Cable MMCX(M)RA
Average Efficiency 62%
Tested in Free space
Dims: 80*30mm
RoHS Compliant
SPE-11-8-045/E
Page 1 of 11
1. Introduction
This high performance, low profile, PCB antenna is based on smart TheStripe™ antenna
technology. It consists of a PCB antenna and mini coaxial cable. The product is a high
gain Penta-band 850/900/1800/1900/2100 antenna suitable for worldwide GSM, UMTS
and WCDMA applications. Its high efficiency (62% average) makes it an ideal choice
to pass telecom operator’s testing approvals. The product should be tested in free
space conditions connected to the client’s cellular device.
Further optimization can be done upon receipt of the client’s device at a local Taoglas
facility.
2. Specifications
CELLULAR
Communication system
Frequency Band
VSWR
AMPS
850MHz
1.58
GSM
900MHz
1.78
DCS
1800MHz
1.51
PCS
1900MHz
1.38
UMTS/WCDMA
2100MHz
1.37
Return Loss
-12.96
56.84%
0.01dBi
-2.45dB
-11.00
72.98%
1.2dBi
- 1.37dB
-13.79
-15.81
55.79%
1.25dBi
-2.53dB
-16.11
Efficiency
63.52%
2.66dBi
- 1.97dB
50 Ohm
63.25%
1.43dBi
-1.99dB
Peak Gain
Average Gain
Impedance
Radiation Pattern
Polarization
Omnidirectional
Horizontal
MECHANCIAL
Dimensions
RF Cable
80 * 30mm
RF Coaxial Cable ψ1.13 ± 0.1mm, L = 100 mm
Gray Color
RF Connector
MMCX(M)RA
ENVIRONMENTAL
-40°C to + 85°C
Operation Temperature
Storage Temperature
Relative Humidity
-40°C to + 95°C
40% to 95%
SPE-11-8-045/E
Page 2 of 11
3. Antenna Characteristics
3.1. Return loss
SPE-11-8-045/E
Page 3 of 11
4. Reliability
Test Items
Procedure
Requirement
Thermal Shock
Starting at -40 for 30minutes and
then cycled to +85 to remain
1. The value of return loss
must be within product
30minutes (a complete cycle). To
specifications after this test.
repeat 5 complete cycles. (Refer to 2. No physical deformation
IEC 68-2-14 Method Na)
should be evident.
Storage Temperature
(Cold)
Samples must be put into -30°C
chamber for 72 hours and samples
shall be powered during test.
1. The value of return loss must
be within product
specifications after this test.
2. No physical deformation
should be evident.
(Refer to IEC 68-2-1 Method Aa)
Storage Temperature
(Dry Heat)
Samples must be put into +75°C
chamber for 72 hours and samples
shall be powered during test.
1. The value of return loss must
be within product
specifications after this test.
2. No physical deformation
should be evident.
(Refer to IEC 68-2-1 Method Ba)
Operating Temperature Samples must be put into -20°C
1. The value of return loss must
met specification during
test/after test
2. No mechanical defects after
test.
(Cold)
chamber for 2 hours and samples
shall be powered during test.
(Refer to IEC 68-2-1 Method Aa)
Operating Temperature Samples must be put into +65°C
1. The value of return loss must
met specification during
test/after test
(Dry Heat)
chamber for 72 hours and samples
shall be powered during test.
(Refer to IEC 68-2-1 Method Ba)
2. No mechanical defects after
test.
SPE-11-8-045/E
Page 4 of 11
5. Antenna Test Procedures and Setup
5.1. Test Procedure for VSWR/Return Loss
5.1.1. STEP 1 Route Cable in Correct Position
5.1.2. STEP 2 Connect Antenna to Module
Connect feed-line to network analyze
5.1.3. STEP 3 - Assemble Antenna in Correct Position
5.1.4. STEP 4 - Assemble Housing
5.2. 3D Radiation Pattern Testing
Test Setup Diagram
SPE-11-8-045/E
Page 5 of 11
5.3. 3D Radiation Pattern Testing
850MHz
900MHz
SPE-11-8-045/E
Page 6 of 11
1800MHz
1900 MHz
2100MHz
SPE-11-8-045/E
Page 7 of 11
5.4. 3D Chamber Testing – Tabular Results
SPE-11-8-045/E
Page 8 of 11
6. Mechanical Drawings (Unit: mm)
6.1. Dimensions and Drawing
6.2. Antenna Placement
Antenna designed to for testing when connected outside the client’s device and placed
in frees pace conditions, for example on plastic foam block. Final product can use pre-
applied double sided adhesive tape, slot or screw mount.
SPE-11-8-045/E
Page 9 of 11
7. Packaging (Unit: mm)
SPE-11-8-045/E
Page 10 of 11
Taoglas makes no warranties based on the accuracy or completeness of the contents of this document
and reserves the right to make changes to specifications and product descriptions at any time without
notice.
Taoglas reserves the rights to this document and the information contained herein. Reproduction, use or
disclosure to third parties without express permission is strictly prohibited.
Copyright © Taoglas Ltd.
SPE-11-8-045/E
Page 11 of 11
相关型号：
©2020 ICPDF网 联系我们和版权申明