IQ32018QGC25NRS-G [SYNQOR]
DC-DC Regulated Power Supply Module, 1 Output, 50W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8;
| 型号： | IQ32018QGC25NRS-G |
| 厂家： | 
SYNQOR WORLDWIDE HEADQUARTERS |
| 描述： | DC-DC Regulated Power Supply Module, 1 Output, 50W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8 |
| 文件： | 总12页 (文件大小：1812K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Technical
Specification
IQ32xxxQGXxx
9-75V
100V
1.8-48V
Outputs
50W
Max Power
2250V dc Quarter-brick
Continuous Input Transient Input
Isolation
DC-DC Converter
The InQor quarter-brick converter series is
composed of next-generation, board-mountable,
isolated, fixed switching frequency dc-dc
converters that use synchronous rectification
to achieve extremely high power conversion
efficiency. Each module is supplied completely
encased to provide protection from the harsh
environments seen in many industrial and
transportation applications.
G
A
-
S
R
0
N
1
0
1
@
C
T
G
U
V O
Q
0
0
.
5
5
0
2
3
9
V IN
5
7
I
-
Operational Features
• High efficiency, 85% at full rated load current
• Delivers full power with minimal derating - no heatsink required
• Operating input voltage range: 9-75V
• Fixed frequency switching provides predictable EMI
• No minimum load requirement
Proteatures
Mechanical Features
• Int under-oltae lt
• Output current limit and short circuit protection
• Active back bias mit
utput over-oltage protection
mal shutown
• Industry standard quarter-brick pin-out c
• Size: 1.536" x 2.386" (39.01 .6mm)
• Total height: 0.500” (12.7mm
• Total weight: 3oz (85
ONTENTS
Controeatures
Page No.
• On/Off controto input side
• Remote sene for toltage
• Output voltagtrim ranf -20%, +
y Electrical Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
y Electrical Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
cal Characteristics (15 Vout) & Figures . . . . . . . . . . . . . . . . . . . . 4
ation Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
ards & Qualification Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ed Mechanical Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Flanged Mechanical Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
RING INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Safety Featres
Pending
• Input-to-output isolation: 225
• UL 60950-1 2nd Basic on
• CAN/CSA-C2No. 61-07
• EN609501
• CE Marked 20C Low Voltage Directive
• IEC 61000-4-2
• RoHS compliant (see )
Product # IQ32xxxQGXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005545 Rev. 2
05/11/10
Page 1
Technical
Specification
IQ32xxxQGXxx
IQ32 Family Electrical Characteristics (all output voltages)
Ta = 25 °C, airflow rate = 300 LFM, Vin = 32V dc unless otherwise noted; full operating temperature range is -40 °C to C baseplate temperature
with appropriate power derating. Specifications subject to change without notice.
Parameter
ABSOLUTE MAXIMUM RATINGS
Min.
Typ.
Max. Units Notes & Cdition
Input Voltage
Non-Operating
Operating
Operating Transient Protection
Isolation Voltage
100
75
100
V
V
V
Connuou
Cntinuous
s
lation
Input to Output
Input to Base-Plate
Output to Base-Plate
Operating Temperature
2250
2250
2250
100
125
18
V dc
V dc
°C
C
-40
-55
-2
Baseplate temperature
Storage Temperature
Voltage at ON/OFF input pin
INPUT CHARACTERISTICS
Operating Input Voltage Range
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Lockout Voltage Hysteresis
Recommended External Input Capacitance
Input Filter Component Values (L\C)
DYNAMIC CHARACTERISTICS
Turn-On Transient
9
75
V
100V transi1 s; s1
10.9
8.1
11.5
8.5
3.0
100
.6
8.9
V
V
V
µF
Typic.1-0.2 Ω
µH\µF Internal see Figure E
Turn-On Time
Start-Up Inhibit Time
9
230
0
ms
ms
%
oad, Vout=90% nom.
+125 °C; Figure F
Maxim Output Capacitance
200
0
Output Voltage Overshoot
ISOLATION CHARACTERISTICS
Isolation Voltage (dielectric strength)
Isolation Resistance
Isolation Capacitance (inut to o
Semiconductor Junctieratur
Board Temperature
Transformer Temperature
Maximum Blate Temperat
FEATURE ERISTICS
Switching Freq
e Absolute Maximum Ratings
0
0
MΩ
pF
°C
°C
°C
°C
1
125
25
0
Package rated to 150 °C
UL rated max operating temp 130 °C
See Common Figure 3 for derating curve
230
250
270
kHz
V
Regulation and Isolation stages
ON/OFF Contol
Off-State Volage
On-State Voltae
2.4
1.8
0.8
ON/OFF Control
Pull-Up Voltage
Pull-Up Resistance
Over-Temperature ShutdoTrip Point
Over-Temperature Shutdown RHysteresis
RELIABILITY CHAERIST
Calculated MTBF (TelcR-NWT
Calculated MTIL-217L-HDBK-217F
Field DemonstrBF
Application notes Figures A & B
Average PCB Temperature
5
50
125
10
V
kΩ
°C
°C
6
6
6
2.5
2
10 Hrs. 80% load, 200LFM, 40 °C Ta
10 Hrs. 80% load, 200LFM, 40 °C Ta
10 Hrs. See our website for details
Note 1: Higher valulation capacitance can be added external to the module.
Product # IQ32xxxQGXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005545 Rev. 2
05/11/10
Page 2
Technical
Specification
IQ32xxxQGXxx
Family Figures (all output voltages)
120
100
80
60
40
20
Nominal Vout
Vin min
Vin nom
Vin max
0 30 40 50 60 70 90 100 130 150
Load Curr
Common Figure 1: Typical startup waveform. Input voltage pre-applied, ON/
OFF Pin on Ch 2.
Common Figure ut voltage vad curreng typicurrent limit
s and converter shutdown po
100,000.0
100,000
1.8 V
3.3 V
5 V
V
15 V
24 V
30 V
48 V
10,000.0
1,000.0
100.0
10,000.
000.0
100.0
10.0
0
1
2
5
9
10 11 12 1
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
Incrut (%)
Increase in Vout (%)
Common Figure 3: Trim grapup 1.8 12 V outputs
mon Figure 4: Trim graph for trim-up 15 to 48 V outputs.
10,000.0
All voltag
1,000.0
100.0
10.0
0
4
5
7
8
9
10 11 12 13 14 15 16 17 18 19 20
Decrease in Vout (%)
Common Figure 5: Trim gtrim down.
Product # IQ32xxxQGXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005545 Rev. 2
05/11/10
Page 3
Input:15V
Output:15.0V
Current:3.3A
Part No.:IQ32150QGx03
Technical Specification
IQ32150QGx03 Electrical Characteristics (15.0 Vout)
Ta = 25 °C, airflow rate = 300 LFM, Vin = 32V dc unless otherwise noted; full operating temperature range is -40 °C to +100 °C baseplate temperature
with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
Typ.
Max. Units Notes & Cditio
INPUT CHARACTERISTICS
Maximum Input Current
No-Load Input Current
8.5
250
4.0
A
mA
mA
V
mA
Vin min; trim uent lim
200
2.4
0.72
100
Disabled Input Current
Response to Input Transient
Input Terminal Ripple Current
Recommended Input Fuse
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Regulation
Over Line
Over Load
Over Temperature
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
igure
Faexternal e recomme
TBD
14.85
15
15.15
V
±0.1
±0.1
±0.3
±0.3
225
%
V
-225
14.625
15.375
er samplee, loadature & e
20 MHz bansee No
Full loa
Full oad
Sto thermal der
Outpge 10% Low
5
10
20
3.3
4.3
mV
mV
A
RMS
Operating Output Current Range
Output DC Current-Limit Inception
Output DC Current-Limit Shutdown Voltage
Back-Drive Current Limit while Enabled
Back-Drive Current Limit while Disabled
Maximum Output Capacitance
Output Voltage during Load Current Tranent
Step Change in Output Current (0.1 A
Settling Time
Output Voltage Trim Range
Output Voltage Remote Sense
Output Over-Voltage Protection
EFFICIENCY
0
4.0
9
A
V
A
Negative crawn from output
Negative curreawn from output
ut nominal at full load (resistive load)
0
50
1,000
950
200
mV
µs
%
%
%
0% to 50% Iout max
To witin 1% Vout nom
Across Pins 8&4; Common Figures 3-5; see Note 2
cross Pins 8&4
20
10
0
17.6
.3
Over full temp range
100% Load
50% Load
8
86
%
%
See Figure 1 for efficiency curve
See Figure 1 for efficiency curve
Note 1: Outpuis terminated ceramic and 15 -ESR tantalum rs. For applications requiring reduced output voltage ripple and
noise, consor application(e-mail: suppqor.com)
Note 2: Trim-limited belo10% at low line and f
Product # IQ32xxxQGXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005545 Rev. 2
05/11/10
Page 4
Technical
Specification
IQ32xxxQGXxx
BASIC OPERATION AND FEATURES
CONTROL FEATURES
This converter series uses a two-stage power conversion
topology. The first stage is a buck-converter that keeps the
output voltage constant over variations in line, load, and
temperature. The second stage uses a transformer to provide
the functions of input/output isolation and voltage step-up or
step-down to achieve the output voltage required.
REMOTE ON/OFF (Pin 2): The input, Pin 2, permits
the user to control when the convertor off. This input
is referenced to the return nal of put bus, Vin(-).
The ON/OFF signal is active laning low turns the
converter on). Figure A etails fsible cuits for driving
the ON/OFF pin. Figure B is a detaof the internal ON/
OFF circuitry.
Both the first stage and the second stage switch at a fixed
frequency for predictable EMI performance. Rectification of
the transformer’s output is accomplished with synchronous
rectifiers. These devices, which are MOSFETs with a very low
on-state resistance, dissipate far less energy than Schottky
diodes. This is the primary reason that the converter has such
high efficiency, even at very low output voltages and very high
output currents.
REMOTE SENSE(ns 7 an5): The SENSE(+) inputs
correct for tage drng the onductors ect the
converter’s output pins tad.
Pin 7 ould be connected o Vout(+Pin 5 should be
conneo Vout(-) at the point on he boere regulation
s desiemote cnnection ae load djust or a
voltage das large as that ied in datasheet,
that is
These converters are offered totally encased to withstand har
environments and thermally demanding applications. Dissip
throughout the converter is so low that it does not require a
heatsink for operation in many applications; however, adding
a heatsink provides improved thermal derating peormance in
extreme situations.
t(+) - Vout(] – [V(+) - Vsense(-)] <
nse Range out
Pins 7 and 5 ust onnected fproper regulation of
thoutput voltag. If connections are not made, the
converter will deliver an ovoltage that is slightly higher
than its d value.
This series of converters use the industry standard footp
pin-out configuration.
Note: the outr-voltage protection circuit senses the
vge acros th(pins 8 and 4) to determine when
it should trigger, not e voltage across the converter’s sense
leads (pins 7 and 5). Therefore, the resistive drop on the board
ould be small ough so that output OVP does not trigger,
during lad transients.
ON/OFF
/OFF
in(_)
Remote Enable Circui
NegatLogic
nently Enable
5V
5V
ONFF
50k
/
ON/O
Vin(_)
ON/OFF
Vin(_)
50k
TTL
100pF
Vin(_)
Open CollectoCircuit
Dct Logic Drive
Figure A: Various circuits iving the ON/OFF pin.
Figure B: Internal ON/OFF pin circuitry
Product # IQ32xxxQGXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005545 Rev. 2
05/11/10
Page 5
Technical
Specification
IQ32xxxQGXxx
OUTPUT VOLTAGE TRIM (Pin 6): The TRIM input permits the
user to adjust the output voltage across the sense leads up or
down according to the trim range specifications.
PROTECTION FEATURES
Input Under-Voltage Lockout: onverter is designed
to turn off when the input voltage is helping avoid an
input system instability prodescrmore detail in
the application note titled “Iystem ability” on our
website. The lockout ciritry is a rator h dc hysteresis.
When the input voltage is rising, it meed the typical Turn-
On Voltage Thresd value (listed on specificatins page)
before the conill ton. Oncthe converter is on,
the input voltage l below e typical Tn-Off Voltage
Threshold e befornvertr will turn
To decrease the output voltage, the user should connect a
resistor between Pin 6 and Pin 5 (SENSE(-) input). For a desired
decrease of the nominal output voltage, the value of the resistor
should be
511
R
=
- 10.22 (kW)
trim-down
(D%)
where
Vnominal – Vdesired
Vnominal
OutpCurrent Limit: Tmaximum current limit rem
constas the output vltage dropsever, once the
impedthe load aross the ouut is sough to make
he outge drobelow the sfied OuC Curent-
Limit Shuttage, the cnvertes off.
=
x 100%
D%
To increase the output voltage, the user should connect a
resistor between Pin 6 and Pin 7 (SENSE(+) input). For a desired
increase of the nominal output voltage, the value of the resistor
should be
verter then enters a p modre it repeatedly
d off at a 5 (nomrequency with a 5% duty
cycle untthe short cuit conditioemoved. This prevents
excessive heating oonverter or ad board.
5.11VOUT (100+D%)
x
511
_
R
_
=
(kW)
trim-up
.22
)
(
1.225D%
D%
Otput Over-Volage If the voltage across the output
pins exces the Output Ovtage Protection threshold, the
convertemediately stop itching. This prevents damage
to the load cie to 1) excessive series resistance in output
curent path from rter output pins to sense point, 2) a
releae of a short-circcondition, or 3) a release of a current
limit condition. Load capacitance determines exactly how high
he output voltagwill rise in response to these conditions. After
ms the cnverter will automatically restart.
where
V
= Nominal Output Voltage
out
Trim graphs show the relationship betwen the trim resistor
value and Rtrim-up and Rtrim-dowing he total rathe
output voltage can be trimmed up
Note: the TRIM feature does not affect the at which the
output over-voltage protectiit is triggered. Trimminhe
output voltage too hmay ce over-voltage prot
circuit to engage, ply durinsients.
Omperature Shutdown: A temperature sensor on
the converter senses the average temperature of the module.
e thermal shutdown circuit is designed to turn the converter
hen the temperature at the sensed location reaches the
er-Temperature Shutdown value. It will allow the converter
to turn on again when the temperature of the sensed location
falls by the amount of the Over-Temperature Shutdown Restart
Hysteresis value.
It is not necessary for thto adcapacitaat the Trim
pin. The ns internally bto eliminate
Total DC VarV
specification, the variation of thvalue of
: or the cor to mfull
OUT
,
due to both trmming aremote loltage ops, should ot
be greater than hat specified for the voltagrange.
Product # IQ32xxxQGXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005545 Rev. 2
05/11/10
Page 6
Technical
Specification
IQ32xxxQGXxx
APPLICATION CONSIDERATIONS
Input System Instability: This condition can occur because Application Circuits: Figure C provia typical circuit diagram
any dc-dc converter appears incrementally as a negative which details the input filtering and vomming.
resistance load. A detailed application note titled “Input System
Instability” is available on the SynQor website which provides
an understanding of why this instability arises, and shows the
preferred solution for correcting it.
ut(+)
Vin(+)
Electrolytic
Capacitor
)
External
Input
Filter
Rtrim-up
Vin
Tri
OFF
Vin_)
Cload
Rtrim-do
load
nse(_)
Vout(_)
Figure C: Typicaapplication circuit (egative logic uninently enabled).
Input Filtering and External Ce: Figure D provides The recommended extenal input capacitance is specified in the
a diagram showing the internal input filents. This filter nput Characterisics section on the Electrical Characteristics
dramatically reduces input teinal ripple curhich otherwise e. More dtailinformation is available in the application note
could exceed the rating of aal electrolytic input captor. EMI Chracteristics” on the SynQor website.
L
Vin(+
C
Vin(_
FiD: Internal Input ter Diagram (component values listed on the specifications page).
Product # IQ32xxxQGXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005545 Rev. 2
05/11/10
Page 7
Technical
Specification
IQ32xxxQGXxx
Startup Inhibit Period: The Startup Inhibit Period ensures that When the ON/OFF pin goes high after t2, the Startup Inhibit
the converter will remain off for approximately 200 ms when it is Period has elapsed, and the output within the typical
shut down for any reason. When an output short is present, this Turn-On Time.
generates a 5 Hz “hiccup mode,” which prevents the converter
from overheating. In all, there are seven ways that the converter
can be shut down, initiating a Startup Inhibit Period:
Thermal Considerations: The um oing base-plate
temperature, TB, is 100 As lonuserthermal system
keeps TB < 100 ºC, the converter can its full rated power.
•ꢀ InputꢀUnder-VoltageꢀLockout
•ꢀ InputꢀOver-VoltageꢀLockout
•ꢀ OutputꢀOver-VoltageꢀProtection
•ꢀ OverꢀTemperatureꢀShutdown
•ꢀ CurrentꢀLimit
A power derating an be alculated or any heatsink that is
attached to the basef the coerter. It ily necessary
to determine thermnce, RTHBA, of tsink
between the base-plate aambient air for a give
rate. s information is ully availabe from the heatsink
vendofollowing fomula can the be udetermine the
aximuer the coverter can dipate fven trmal
condition e-plate is to be no r than C.
•ꢀ ShortꢀCircuitꢀProtection
•ꢀ TurnedꢀoffꢀbyꢀtheꢀON/OFFꢀinput
Figure E shows three turn-on scenarios, where a Startup Inh
Period is initiated at t0, t1, and t2:
1TA
Pmax
=
diss
RTH
BA
Before time t0, when the input voltage is below the UVL threshold,
the unit is disabled by the Input Under-Voltage Lockout feature.
When the input voltage rises above the UVL threhe Input
Under-Voltage Lockout is released, and a Startup Ind is
initiated. At the end of this delay, the ON/OFF pin is e
and since it is active, the unit turns on.
This value of power ation can thused in conjunction
with the data shn in e 2 to deterine the maximum load
curnt (and powerthat onverter can deliver in the given
thermal coition.
For conveniewer derating curves for an encased converter
without a heatsinwith a typical heatsink are provided for
eacutput voltag.
At time t1, the unit is disabled by thON/OF pin, and t cannot
be enabled again until the Startut Period has elapd.
V
in
Under-Voltage
Lockout Turn-
On Threshold
ON/OFF
(neg loic)
OFF
ON
OFF
ON
9ms (typical
turn on time)
V
out
20
pical sta
bit perio
200ms
200ms
t
t1
t2
Figure E: Startup Inhibit Period (turn-on time not to scale)
Product # IQ32xxxQGXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005545 Rev. 2
05/11/10
Page 8
Technical
Specification
IQ32xxxQGXxx
Standards & Qualification Testing
Parameter
Notes & Conditions
STANDARDS COMPLIANCE
UL 60950-1 2nd Ed. 2007
CAN/CSA-C22.2 No. 60950-1-07
EN60950-1 Ed. 2.0
Pending
Basic Insulation
CE Marked
2006/95/EC Low Voltage Directive
IEC 61000-4-2
ESD test, 8 kV - NP, 15 kV air - NP (Normal Permanc)
Note: An external input fuse must always be used to meet these safety requirements. Contact Syofficsafety certites on new
releases or download from the SynQor website.
Parameter
QUALIFICATION TESTING
Life Test
# Units Test Condition
32
5
5
95% rated Vin and load, uing point, 000 ho
10-5ep, 0.060" total excursion, 1 mip, 120 for 3 is
1in x, y and z axis
Vibration
Mechanical Shock
Temperature Cycling
Power/Thermal Cycling
Design Marginality
Humidity
10
5
-40 °C to 100 ramp 15 °C/mi., 500
Toperatin= min to max, Vin = min ax, full load, 1es
Tmin-10 °C tTmax+10 °C, 5 °C ste= min to max05% load
°C, 85% RH00 hours, conuous lied except 5 min/day
Solderability
Altitude
15 pin-883, method 2003
721 km), se
2
Note: A conductive cooling design is generally neded for high altitude aplications because ly poor convective cooling at rare atmospheres.
Product # IQ32xxxQGXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005545 Rev. 2
05/11/10
Page 9
Technical
Specification
IQ32xxxQGXxx
Encased Mechanical Drawing
1.536 ±0.020 (39.01 ±0.5)
1. 030 (26.16)
0.600 (15.24)
0.450 (11.43)
0.300 (7.62)
0.150 (3.81)
0.253±0.020 (6.4±0.5)
0.500±0
(12.7±0.63
OveraHeight
8 7 6 5 4
0.260.020
(6.5)
2.386
± 0.020
(60.6± 0.5)
0.18±0.01
(4.50.25)
Top View
2.00
(50.8)
Side Vie
6
1
3
2
hreaded In
4 Places
S
(11.89±0.5)
0468±0.020
0.00 (7.62)
0.183±.020
(4.65)±0.5
0.60 (15.24)
NOTES
PNꢀDESIGNATIONS
1)
M3 screws used to bolt unite to other surces (such
a heatsink) must not ceed 04 mm) depth below t
surface of the bas
Name ꢀFunction
1
(+) Positive input voltage
2)
TTL input to turn converter on and off,
referenced to Vin(–), with internal pull up.
Applied torque per sld not d 6in-lb. (0.7 Nm).
2
ON/OFF
Vin(–)
3)
4)
Baseplate flatness tolera04" (0mm) TIR urface.
Pins 1-3re 0.040” (1.0meter, with 0.03mm)
diamethoulders.
Negative input voltage
4
Vout(–) Negative output voltage
5)
Pins 4 and 8 1.57 mm) diamet.100" ()
diameter sandoff
1
5
SENSE(–) Negative remote sense
2
6
TRIM
Output voltage trim
6)
All Pins: Matrial - CopAlloy- FinisHS 6/6Mtte Tin o
Nickel plate
3
7
8
SENSE(+) Positive remote sense
Vout(+) Positive output voltage
7)
Weight: 3.02 oz(85.7 g) typica
8)
All dimensions in nches (mm)
Notes:
1)
Tolerances: x.xx +/-0.02 . (x.x +/-0.5mm)
x.xxx +/-0.01.xx +/-0.25mm)
SENSE(–) should be connected to Vout(–) either remotely
or at the converter.
9)
Workmanship: Meets or ePC-A-610C Class II
2)
3)
Leave TRIM pin open for nominal output voltage.
10)
Recommended pin length is 0.76mm) reater than the PCB
thickness.
SENSE(+) should be connected to Vout(+) either remotely
or at the converter.
Product # IQ32xxxQGXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005545 Rev. 2
05/11/10
Page 10
Technical
Specification
IQ32xxxQGXxx
Flanged Mechanical Drawing
.01 [0.2]
OVERALL HEIGHT
.500 ±.025
[12.7 ±0.63]
.45 [ 11
30 [ 7.6 ]
.15 [ 3.8 ]
2.200 ±.020 [ 55.88 ±0.5]
1.536 ±.020 [ 39.01 ±0.5]
.18
[ 4.6 ]
SEE NOTE 5
R .065
[ 1,65 ]
6
7
8
2.00
TOP VIEW
TTOM VIEW
]
07
]
2.386 ±
[ 60.6 ±0.
1.66
[ 42.2
]
1.01
[ 25.7
]
.36
[ 9.1 ]
3
2
1
1
.70
[ 17.8
.183 ±.020
[ 4.65 ±0.5]
.30 [ 7.6 ]
.60 [ 15.2
]
.13
[ 3.2 ]
BOTTOSIDE CLEARANCE
±.020
.800 ±.020
[ 20.32
]
.02 [ 0.6 ]
.51
.25]
NOTES
PINꢀDESIGNATIONS
1)
Applied torque phould ned 5in-lb.
(3in-lb recommended
Baseplate flatness tolera1” (.2m) TIR for face.
PiName ꢀFunction
1
Vin(+) Positive input voltage
2)
3)
TTL input to turn converter on and off,
referenced to Vin(–), with internal pull up.
2
ON/OFF
Vin(–)
Pins 1-0.040” (1.02ameter, with 0.03mm)
diameter ulders.
3
Negative input voltage
4)
5)
Pins 4 and 8 ar57 mm) diametr 100" (2.)
diameter stndoff
All Pins: Mateial - CoppAlloy, FiniS 6/6Tin ov
Nickel plate
4
Vout(–) Negative output voltage
1
5
SENSE(–) Negative remote sense
2
6
TRIM
Output voltage trim
6)
7)
Total Weight: 3.z (88.5 g)
All dimensions in inches (mm)
Tolerances: x.xx +/-0.0. (x.x +/-0.5mm)
x.xxx +/-(x.xx +/-0.25mm)
3
7
8
SENSE(+) Positive remote sense
Vout(+) Positive output voltage
Notes:
1)
SENSE(–) should be connected to Vout(–) either remotely
or at the converter.
8)
9)
Workmanship: Meets or exC-A-610C Class II
Recommended pth is 0.6mm) reater than the PCB
thickness.
A thermal ce mal is required to assure proper heat transfer
from the flaseple to the cooling surface. Thermal grease
may be used, rials such as Thermalloy’s Grafoil or Bergquist
HiFlow and Softfler similar products are available from many
heatsink manufactur
2)
3)
Leave TRIM pin open for nominal output voltage.
10)
SENSE(+) should be connected to Vout(+) either remotely
or at the converter.
Product # IQ32xxxQGXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005545 Rev. 2
05/11/10
Page 11
Technical
Specification
IQ32xxxQGXxx
PART NUMBERING SYSTEM
ORDERING INFORMATION
The part numbering system for SynQor’s dc-dc converters follows the format
shown in the example below.
The tables below show the valid model numbers and ordering options for
converters in this product family. When nQor converters, please
ensure that you use the complete 1charaumber consisting of
the 12 character base part number e additacters for options.
Add “-G” to the model number for compl
IQ 32 050 Q G C 10 N R S - G
Cinuous
Input Voltage
ut
ximum Output
Model Number
Current
6/6 RoHS
IQ32018QGw25xyz
IQ32033QGw15
IQ32050QGw10xyz
IQ32070QG7xyz
IQ32120QGw04xz
IQ320QGw03xyz
IQ32Gw02xyz
IQ3202xyz
IQ3248yz
9-75V
9-7
5V
9-7
9-75
9-75V
9-75V
3.3
5.0
7.0
12
Options (see
Ordering Information)
15
10
Output Current
Thermal Design
Performance Level
Package Size
3.3
20
1.6
1.0
15
24
30
Output Voltage
Input Voltage
The ollowing oust be incld in plae w x y paces in the
odel numbers listed above.
Product Family
OptioDescw x y z
Design
C - Encased with
eaded Basepla
V Encased with
Enabe Logi
n Style
Feature Set
The first 12 characters comprise the base part number and the last 3
characters indicate available options. The “-G” suffix indictes 6/6 RoHS
compliance.
tive
R - 0.180"
S - Standard
Flanged Beplate
Application Notes
A variety of application notes and technical white ppers can be owloade
in pdf format from our website.
Noall combinations id part numbers, please contact SynQor for
availabity. See te Produummary web page for more options.
RoHS Compliance: The EU estriction of Hardous
Substances) Directive bans the use omium, Hexavalent
Chromium, Mercury, Polybrominated Biphenyls Polybrominated
Diphenyl Ether (PBDE) in ElecElectronic Equ. This SynQor
product is 6/6 RoHS compliant. re information please rto
SynQor’s RoHS addendailable oHS Compliance /
Free Initiative web -mail ohs@synqor.com
.
TENTS
SQor holds the following U.S. patents, one or more of which apply to
each product listed in this document. Additional patent applications may
be pending or filed in the future.
5,999,417
6,731,520
7,072,190
7,272,023
6,222,742
6,894,468
7,085,146
7,558,083
6,545,890
6,896,526
7,119,524
7,564,702
6,577,109
6,927,987
7,269,034
6,594,159
7,050,309
7,272,021
Contact SnQor for further inatin:
Phone:
78-849-0600
Warranty
Toll Free: 567-9596
SynQor offers a two (2) year limited warranty. Complete warranty
information is listed on our website or is available upon request from
SynQor.
Fax:
E-mail
:
979-0602
powenqor.com
www.synqor.com
Ad: 155 Swanson Road
Boxborough, MA 01719
SA
Information furnished by SynQor is believed to be accurate and reliable.
However, no responsibility is assumed by SynQor for its use, nor for any
infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any
patent or patent rights of SynQor.
Product # IQ32xxxQGXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005545 Rev. 2
05/11/10
Page 12
相关型号：
IQ32018QGV25NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 50W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8
SYNQOR
IQ32018QTC35NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 86W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8
SYNQOR
IQ32018QTD35NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 86W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8
SYNQOR
IQ32018QTV35NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 86W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8
SYNQOR
IQ32033HPC45NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 165W, Hybrid, ROHS COMPLIANT, HALF BRICK PACKAGE-8
SYNQOR
IQ32033HPD45NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 165W, Hybrid, ROHS COMPLIANT, HALF BRICK PACKAGE-8
SYNQOR
IQ32033HTC33NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 108.9W, Hybrid, ROHS COMPLIANT, HALF BRICK, PACKAGE-8
SYNQOR
IQ32033HTV33NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 108.9W, Hybrid, ROHS COMPLIANT, HALF BRICK, PACKAGE-8
SYNQOR
IQ32033QGV15NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 50W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8
SYNQOR
IQ32050HPD32NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 165W, Hybrid, ROHS COMPLIANT, HALF BRICK PACKAGE-8
SYNQOR
©2020 ICPDF网 联系我们和版权申明