TS3702ID [STMICROELECTRONICS]
MICROPOWER DUAL CMOS VOLTAGE COMPARATORS; 双微功耗CMOS电压比较器型号: | TS3702ID |
厂家: | ST |
描述: | MICROPOWER DUAL CMOS VOLTAGE COMPARATORS |
文件: | 总11页 (文件大小:117K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TS3702
Micropower dual CMOS voltage comparators
Features
■ Push-pull CMOS output (no external pull-up
resistor required)
N
DIP8
(Plastic package)
■ Extremely low supply current: 9μA typ /
comparator
■ Wide single supply range: 2.7V to 16V or dual
supplies (±1.35V to ±8V)
■ Extremely low input bias current: 1pA typ
■ Extremely low input offset currents: 1pA typ
D
SO8
■ Input common-mode voltage range includes
(Plastic micropackage)
GND
12
■ High input impedance: 10 Ω typ
■ Fast response time: 2μs typ for 5mV overdrive
■ Pin-to-pin and functionally compatible with
P
bipolar LM393
TSSOP8
(Thin shrink small outline package)
Description
The TS3702 is a micropower CMOS dual voltage
comparator with extremely low consumption of
9μA typ / comparator (20 times less than bipolar
LM393). The push-pull CMOS output stage allows
power and space saving by eliminating the
external pull-up resistor required by usual open-
collector output comparators.
Pin connections
(Top view)
+
Output 1
Inverting Input 1
1
2
3
4
8
7
6
5
VCC
Output 2
-
+
Non-inverting Input 1
Inverting Input 2
Non-inverting Input 2
-
-
+
VCC
Thus response times remain similar to the LM393.
February 2007
Rev 3
1/11
www.st.com
11
Schematic diagram
TS3702
1
Schematic diagram
Figure 1.
Schematic diagram (for 1/2 TS3702)
VCC
+
T10
T1
T2
T9
T17
R1
T11
T12
T18
T21
Input -
Input +
T3
T4
Output
T13
T8
T19
T20
T5
T7
T14
T15
T16
T6
VCC
-
2/11
TS3702
Absolute maximum ratings and operating conditions
2
Absolute maximum ratings and operating conditions
Table 1.
Symbol
Absolute maximum ratings
Parameter
Value
Unit
+
VCC
Supply voltage (1)
18
±18
18
V
V
Vid
Vi
Differential input voltage (2)
Input voltage (3)
V
Vo
Io
Output voltage
18
V
Output current
20
mA
mA
IF
Forward current in ESD protection diodes on input (4)
Power dissipation (5)
50
DIP8
SO8
1250
710
pd
mW
TSSOP8
625
Tstg
ESD
Storage temperature range
HBM: human body model(6)
MM: machine model(7)
-65 to +150
°C
V
400
50
V
CDM: charged device model(8)
1.5
kV
1. All voltage values, except differential voltage, are with respect to network ground terminal.
2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
3. The magnitude of the input and the output voltages must never exceed the magnitude of the positive and
negative supply voltages.
4. Guaranteed by design.
5. Pd is calculated with Tamb = +25°C, Tj = +150°C and
R
thja = 100°C/W for DIP8 package
Rthja = 175°C/W for SO8 package
Rthja = 200°C/W for TSSOP8 package
6. Human body model: A 100pF capacitor is charged to the specified voltage, then discharged through a
1.5kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations
while the other pins are floating.
7. Machine model: A 200pF capacitor is charged to the specified voltage, then discharged directly between
two pins of the device with no external series resistor (internal resistor < 5Ω). This is done for all couples of
connected pin combinations while the other pins are floating.
8. Charged device model: all pins and the package are charged together to the specified voltage and then
discharged directly to the ground through only one pin. This is done for all pins.
Table 2.
Symbol
Operating conditions
Parameter
Value
Unit
Supply voltage
+
VCC
V
V
TS3702C, TS3702I
TS3702M
2.7 to 16
4 to 16
Vicm
Common mode input voltage range
Operating free-air temperature range
0 to VCC+ -1.5
TS3702C
TS3702I
TS3702M
0 to +70
-40 to +125
-55 to +125
Toper
°C
3/11
Electrical characteristics
TS3702
3
Electrical characteristics
+
-
Table 3.
Symbol
V
= 3V, V = 0V, T
= 25°C (unless otherwise specified)
CC
cc
amb
Parameter
Min.
Typ.
Max.
Unit
Input offset voltage (1)
Vio
mV
Vic = 1.5V
5
Tmin ≤ Tamb ≤ Tmax
6.5
Input offset current (2)
Iio
pA
Vic = 1.5V
Tmin ≤ Tamb ≤ Tmax
1
1
300
600
(2)
Input bias current
Iib
pA
V
Vic = 1.5V
Tmin ≤ Tamb ≤ Tmax
Input common mode voltage range
0
0
VCC+-1.2
VCC+ -1.5
Vicm
CMR
SVR
Tmin ≤ Tamb ≤ Tmax
Common-mode rejection ratio
Vic = Vicm min
80
75
dB
dB
V
Supply voltage rejection ratio
VCC+ = 3V to 5V
High level output voltage
VOH
VOL
ICC
Vid = 1V, IOH = -4mA
Tmin ≤ Tamb ≤ Tmax
2
1.8
2.4
Low level output voltage
Vid = -1V, IOL = 4mA
Tmin ≤ Tamb ≤ Tmax
mV
μA
μs
300
7
400
575
.
Supply current (each comparator)
No load - Outputs low
Tmin ≤ Tamb ≤ Tmax
20
25
.
Response time low to high
tPLH
Vic = 0V, f = 10kHz, CL = 50pF, overdrive = 5mV
TTL input
1.5
0.7
Response time high to low
tPHL
μs
Vic = 0V, f = 10kHz, CL = 50pF, overdrive = 5mV
TTL input
2.2
0.15
1. The specified offset voltage is the maximun value required to drive the output up to 2.5V or down to 0.3V.
2. Maximum values include unavoidable inaccuracies of the industrial tests.
4/11
TS3702
Electrical characteristics
+
-
Table 4.
Symbol
V
= 5V, V = 0V, T
= 25°C (unless otherwise specified)
CC
cc
amb
Parameter
Min.
Typ.
Max.
Unit
Input offset voltage
Vic = Vicm min, Vcc+ = 5V to 10V (1)
1.2
5
Vio
mV
Tmin ≤ Tamb ≤ Tmax
6.5
Input offset current (2)
Iio
pA
Vic = 2.5V
Tmin ≤ Tamb ≤ Tmax
1
1
300
600
(2)
Input bias current
Iib
pA
V
Vic = 2.5V
Tmin ≤ Tamb ≤ Tmax
Input common mode voltage range
0
0
VCC+-1.2
VCC+ -1.5
Vicm
CMR
SVR
Tmin ≤ Tamb ≤ Tmax
Common-mode rejection ratio
Vic = Vicm min
82
90
dB
dB
V
Supply voltage rejection ratio
VCC+ = +5V to +10V
High level output voltage
VOH
VOL
ICC
Vid = 1V, IOH = -4mA
Tmin ≤ Tamb ≤ Tmax
4.5
4.3
4.7
Low level output voltage
mV
Vid = -1V, IOL = 4mA
Tmin ≤ Tamb ≤ Tmax
200
9
300
375
Supply current (each comparator)
μA
No load - Outputs low
Tmin ≤ Tamb ≤ Tmax
20
25
Response time low to high
Vic = 0V, f = 10kHz, CL = 50pF, overdrive = 5mV
Overdrive = 10mV
Overdrive = 20mV
Overdrive = 40mV
TTL input
1.5
1.1
0.9
0.7
0.6
tPLH
μs
Response time high to low
Vic = 0V, f = 10kHz, CL = 50pF, overdrive = 5mV
Overdrive = 10mV
Overdrive = 20mV
2.2
1.6
1.1
tPHL
μs
Overdrive = 40mV
TTL input
0.75
0.17
Fall time
tf
ns
f = 10kHz, CL = 50pF, overdrive 50mV
30
1. The specified offset voltage is the maximun value required to drive the output up to 4.5V or down to 0.3V.
2. Maximum values include unavoidable inaccuracies of the industrial tests.
5/11
Package information
TS3702
4
Package information
In order to meet environmental requirements, STMicroelectronics offers these devices in
®
ECOPACK packages. These packages have a Lead-free second level interconnect. The
category of second level interconnect is marked on the package and on the inner box label,
in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics
trademark. ECOPACK specifications are available at: www.st.com.
6/11
TS3702
Package information
4.1
DIP8 package mechanical data
Dimensions
Ref.
Millimeters
Inches
Min.
Typ.
Max.
Min.
Typ.
Max.
A
a1
B
3.3
0.130
0.7
0.028
0.055
0.036
1.39
0.91
1.65
1.04
0.065
0.041
B1
b
0.5
0.020
b1
D
E
0.38
0.5
9.8
0.015
0.020
0.386
8.8
0.346
0.100
0.300
0.300
e
2.54
7.62
7.62
e3
e4
F
7.1
4.8
0.280
0.189
I
L
3.3
0.130
Z
0.44
1.6
0.017
0.063
7/11
Package information
TS3702
4.2
SO8 package mechanical data
Dimensions
Ref.
Millimeters
Typ.
Inches
Typ.
Min.
Max.
Min.
Max.
A
A1
A2
B
1.35
0.10
1.10
0.33
0.19
4.80
3.80
1.75
0.25
1.65
0.51
0.25
5.00
4.00
0.053
0.04
0.069
0.010
0.065
0.020
0.010
0.197
0.157
0.043
0.013
0.007
0.189
0.150
C
D
E
e
1.27
0.050
H
5.80
0.25
0.40
6.20
0.50
1.27
0.228
0.010
0.016
0.244
0.020
0.050
h
L
k
8° (max.)
ddd
0.1
0.04
8/11
TS3702
Package information
4.3
TSSOP8 package mechanical data
Dimensions
Ref.
Millimeters
Typ.
Inches
Min.
Max.
Min.
Typ.
Max.
A
A1
A2
b
1.2
0.047
0.006
0.041
0.012
0.008
0.122
0.260
0.177
0.05
0.80
0.19
0.09
2.90
6.20
4.30
0.15
1.05
0.30
0.20
3.10
6.60
4.50
0.002
0.031
0.007
0.004
0.114
0.244
0.169
1.00
0.039
c
D
3.00
6.40
4.40
0.65
0.118
0.252
0.173
0.0256
E
E1
e
K
0°
8°
0°
8°
L
0.45
0.60
1
0.75
0.018
0.024
0.039
0.030
L1
9/11
Ordering information
TS3702
5
Ordering information
Table 5.
Order codes
Temperature
Part number
Package
Packaging
Marking
range
TS3702CN
DIP8
SO8
Tube
Tube or tape & reel
Tube
TS3702CN
3702C
0°C, +70°C
TS3702CD/CDT
TS3702IN
DIP8
TS3702IN
3702I
TS3702ID/IDT
TS3702IPT
-40°C, +125°C
-55°C, +125°C
SO8
Tube or tape & reel
Tape & reel
TSSOP8
DIP8
3702I
TS3702MN
Tube
TS3702MN
3702M
TS3702MD/MDT
TS3702MPT
SO8
Tube or tape & reel
Tape & reel
TSSOP8
3702M
6
Revision history
Date
Revision
Changes
2-Jan-2003
1
First release.
PPAP references inserted in the datasheet, see Section 5: Ordering
information on page 10.
2-May-2005
2
PPAP references removed.
26-Feb-2007
3
ESD data added to Table 1 on page 3.
Order codes added to Table 5 on page 10.
10/11
TS3702
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2007 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
11/11
相关型号:
©2020 ICPDF网 联系我们和版权申明