STM32F048T6 [STMICROELECTRONICS]
CRC calculation unit;型号: | STM32F048T6 |
厂家: | ST |
描述: | CRC calculation unit |
文件: | 总98页 (文件大小:1571K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
STM32F048C6 STM32F048G6
STM32F048T6
ARM®-based 32-bit MCU, 32 KB Flash, crystal-less USB FS 2.0,
9 timers, ADC and comm. interfaces, 1.8 V
Datasheet - production data
Features
®
®
• Core: ARM 32-bit Cortex -M0 CPU,
frequency up to 48 MHz
UFQFPN48 7x7 mm
UFQFPN28 4x4 mm
WLCSP36
2.6x2.7 mm
• Memories
– 32 Kbytes of Flash memory
• Nine timers
– 6 Kbytes of SRAM with HW parity
– One 16-bit advanced-control timer for six
channel PWM output
• CRC calculation unit
• Power management
– One 32-bit and four 16-bit timers, with up to
four IC/OC, OCN, usable for IR control
decoding
– Digital and I/Os supply: V = 1.8 V ± 8%
DD
– Analog supply: V
– Selected I/Os: V
= from V to 3.6 V
DDA
DD
= 1.65 V to 3.6 V
– Independent and system watchdog timers
– SysTick timer
DDIO2
– Low power modes: Sleep, Stop
– V
supply for RTC and backup registers
BAT
• Communication interfaces
2
• Clock management
– One I C interface supporting Fast Mode
Plus (1 Mbit/s) with extra current sink,
SMBus/PMBus and wakeup
– 4 to 32 MHz crystal oscillator
– 32 kHz oscillator for RTC with calibration
– Internal 8 MHz RC with x6 PLL option
– Internal 40 kHz RC oscillator
– Two USARTs supporting master
synchronous SPI and modem control, one
with ISO7816 interface, LIN, IrDA, auto
baud rate detection and wakeup feature
– Internal 48 MHz oscillator with automatic
trimming based on ext. synchronization
– Up to two SPIs (18 Mbit/s) with 4 to 16
2
• Up to 37 fast I/Os
programmable bit frames, one with I S
– All mappable on external interrupt vectors
interface multiplexed
– Up to 24 I/Os with 5 V tolerant capability
– USB 2.0 full-speed interface, able to run
from internal 48 MHz oscillator and with
BCD and LPM support
and 8 with independent supply V
DDIO2
• 5-channel DMA controller
• HDMI CEC, wakeup on header reception
• Serial wire debug (SWD)
• 96-bit unique ID
• One 12-bit, 1.0 µs ADC (10 channels)
– Conversion range: 0 to 3.6 V
– Separate analog supply: 2.4 V to 3.6 V
®
• Up to 13 capacitive sensing channels for
• All packages ECOPACK 2
touchkey, linear and rotary touch sensors
• Calendar RTC with alarm and periodic wakeup
from Stop
January 2017
DocID026007 Rev 6
1/98
This is information on a product in full production.
www.st.com
Contents
STM32F048C6 STM32F048G6 STM32F048T6
Contents
1
2
3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Functional overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.1
3.2
3.3
3.4
3.5
ARM®-Cortex®-M0 core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Boot modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cyclic redundancy check calculation unit (CRC) . . . . . . . . . . . . . . . . . . . 13
Power management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.5.1
3.5.2
3.5.3
Power supply schemes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.6
3.7
3.8
3.9
Clocks and startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
General-purpose inputs/outputs (GPIOs) . . . . . . . . . . . . . . . . . . . . . . . . . 15
Direct memory access controller (DMA) . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Interrupts and events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.9.1
3.9.2
Nested vectored interrupt controller (NVIC) . . . . . . . . . . . . . . . . . . . . . . 16
Extended interrupt/event controller (EXTI) . . . . . . . . . . . . . . . . . . . . . . 16
3.10 Analog-to-digital converter (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.10.1 Temperature sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.10.2 Internal voltage reference (V
) . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
REFINT
3.10.3
V
battery voltage monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
BAT
3.11 Touch sensing controller (TSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.12 Timers and watchdogs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.12.1 Advanced-control timer (TIM1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.12.2 General-purpose timers (TIM2, 3, 14, 16, 17) . . . . . . . . . . . . . . . . . . . . 20
3.12.3 Independent watchdog (IWDG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.12.4 System window watchdog (WWDG) . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.12.5 SysTick timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.13 Real-time clock (RTC) and backup registers . . . . . . . . . . . . . . . . . . . . . . 21
3.14 Inter-integrated circuit interface (I2C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.15 Universal synchronous/asynchronous receiver/transmitter (USART) . . . 23
2/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Contents
3.16 Serial peripheral interface (SPI) / Inter-integrated sound interface (I2S) . 24
3.17 High-definition multimedia interface (HDMI) - consumer
electronics control (CEC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.18 Universal serial bus (USB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.19 Clock recovery system (CRS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.20 Serial wire debug port (SW-DP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4
5
6
Pinouts and pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Memory mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6.1
Parameter conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6.1.1
6.1.2
6.1.3
6.1.4
6.1.5
6.1.6
6.1.7
Minimum and maximum values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Typical values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Typical curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Loading capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Pin input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Power supply scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Current consumption measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
6.2
6.3
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
6.3.1
6.3.2
6.3.3
6.3.4
6.3.5
6.3.6
6.3.7
6.3.8
6.3.9
General operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Operating conditions at power-up / power-down . . . . . . . . . . . . . . . . . . 42
Embedded reference voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Supply current characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Wakeup time from low-power mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
External clock source characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Internal clock source characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
PLL characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Memory characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
6.3.10 EMC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6.3.11 Electrical sensitivity characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6.3.12 I/O current injection characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
6.3.13 I/O port characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
6.3.14 NRST and NPOR pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
6.3.15 12-bit ADC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
DocID026007 Rev 6
3/98
4
Contents
STM32F048C6 STM32F048G6 STM32F048T6
6.3.16 Temperature sensor characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
6.3.17
V
monitoring characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
BAT
6.3.18 Timer characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
6.3.19 Communication interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
7
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
7.1
7.2
7.3
7.4
UFQFPN48 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
WLCSP36 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
UFQFPN28 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
7.4.1
7.4.2
Reference document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Selecting the product temperature range . . . . . . . . . . . . . . . . . . . . . . . 93
8
9
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
4/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
STM32F048x device features and peripheral counts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Temperature sensor calibration values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Internal voltage reference calibration values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Capacitive sensing GPIOs available on STM32F048x6 devices . . . . . . . . . . . . . . . . . . . . 18
No. of capacitive sensing channels available on STM32F048x6 devices. . . . . . . . . . . . . . 19
Timer feature comparison. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2
Comparison of I C analog and digital filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2
STM32F048x6 I C implementation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 9.
STM32F048x6 USART implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
STM32F048x6 SPI/I S implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Table 22.
Table 23.
Table 24.
Table 25.
Table 26.
Table 27.
Legend/abbreviations used in the pinout table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
STM32F048x6 pin definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Alternate functions selected through GPIOA_AFR registers for port A . . . . . . . . . . . . . . . 32
Alternate functions selected through GPIOB_AFR registers for port B . . . . . . . . . . . . . . . 33
Alternate functions selected through GPIOF_AFR registers for port F. . . . . . . . . . . . . . . . 33
STM32F048x6 peripheral register boundary addresses. . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Voltage characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Current characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Thermal characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
General operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Operating conditions at power-up / power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Embedded internal reference voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Typical and maximum current consumption from V supply at V = 1.8 V . . . . . . . . . . 45
DD
DD
Typical and maximum current consumption from the V
supply . . . . . . . . . . . . . . . . . 46
DDA
Typical and maximum consumption in Stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Typical and maximum current consumption from the V supply. . . . . . . . . . . . . . . . . . . 47
BAT
Typical current consumption, code executing from Flash memory,
running from HSE 8 MHz crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Switching output I/O current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Peripheral current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Low-power mode wakeup timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
High-speed external user clock characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Low-speed external user clock characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
HSE oscillator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Table 28.
Table 29.
Table 30.
Table 31.
Table 32.
Table 33.
Table 34.
Table 35.
Table 36.
Table 37.
Table 38.
Table 39.
Table 40.
Table 41.
Table 42.
Table 43.
Table 44.
Table 45.
Table 46.
Table 47.
LSE oscillator characteristics (f
= 32.768 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
LSE
HSI oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
HSI14 oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
HSI48 oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
LSI oscillator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
PLL characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Flash memory characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Flash memory endurance and data retention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
EMS characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
EMI characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
ESD absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Electrical sensitivities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
I/O current injection susceptibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
I/O static characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
DocID026007 Rev 6
5/98
6
List of tables
STM32F048C6 STM32F048G6 STM32F048T6
Table 48.
Table 49.
Table 50.
Table 51.
Table 52.
Table 53.
Table 54.
Table 55.
Table 56.
Table 57.
Table 58.
Table 59.
Table 60.
Table 61.
Table 62.
Table 63.
Table 64.
Table 65.
Table 66.
Table 67.
Table 68.
Table 69.
Table 70.
Output voltage characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
I/O AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
NRST pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
NPOR pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
ADC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
R
max for f
= 14 MHz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
AIN
ADC
ADC accuracy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
TS characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
V
monitoring characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
BAT
TIMx characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
IWDG min/max timeout period at 40 kHz (LSI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
WWDG min/max timeout value at 48 MHz (PCLK). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
2
I C analog filter characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
SPI characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
2
I S characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
USB electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
UFQFPN48 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
WLCSP36 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
WLCSP36 recommended PCB design rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
UFQFPN28 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Package thermal characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Clock tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
UFQFPN48 package pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
WLCSP36 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
UFQFPN28 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
STM32F048x6 memory map
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Pin loading conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Pin input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Power supply scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 10. Current consumption measurement scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 11. High-speed external clock source AC timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Figure 12. Low-speed external clock source AC timing diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Figure 13. Typical application with an 8 MHz crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 14. Typical application with a 32.768 kHz crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 15. HSI oscillator accuracy characterization results for soldered parts . . . . . . . . . . . . . . . . . . 58
Figure 16. HSI14 oscillator accuracy characterization results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Figure 17. HSI48 oscillator accuracy characterization results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Figure 18. TC and TTa I/O input characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Figure 19. Five volt tolerant (FT and FTf) I/O input characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Figure 20. I/O AC characteristics definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Figure 21. Recommended NRST pin protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Figure 22. ADC accuracy characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Figure 23. Typical connection diagram using the ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Figure 24. SPI timing diagram - slave mode and CPHA = 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Figure 25. SPI timing diagram - slave mode and CPHA = 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Figure 26. SPI timing diagram - master mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
2
Figure 27. I S slave timing diagram (Philips protocol) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
2
Figure 28. I S master timing diagram (Philips protocol). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Figure 29. UFQFPN48 package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Figure 30. Recommended footprint for UFQFPN48 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Figure 31. UFQFPN48 package marking example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Figure 32. WLCSP36 package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Figure 33. Recommended pad footprint for WLCSP36 package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Figure 34. WLCSP36 package marking example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Figure 35. UFQFPN28 package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Figure 36. Recommended footprint for UFQFPN28 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Figure 37. UFQFPN28 package marking example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
DocID026007 Rev 6
7/98
7
Introduction
STM32F048C6 STM32F048G6 STM32F048T6
1
Introduction
This datasheet provides the ordering information and mechanical device characteristics of
the STM32F048x6 microcontrollers.
This document should be read in conjunction with the STM32F0xxxx reference manual
(RM0091). The reference manual is available from the STMicroelectronics website
www.st.com.
®
®
®
For information on the ARM Cortex -M0 core, please refer to the Cortex -M0 Technical
Reference Manual, available from the www.arm.com website.
8/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Description
2
Description
®
®
The STM32F048x6 microcontrollers incorporate the high-performance ARM Cortex -M0
32-bit RISC core operating at up to 48 MHz frequency, high-speed embedded memories
(32 Kbytes of Flash memory and 6 Kbytes of SRAM), and an extensive range of enhanced
2
peripherals and I/Os. All devices offer standard communication interfaces (one I C, two
2
SPIs/one I S, one HDMI CEC and two USARTs), one USB Full-speed device (crystal-less),
one 12-bit ADC, four 16-bit timers, one 32-bit timer and an advanced-control PWM timer.
The STM32F048x6 microcontrollers operate in the -40 to +85 °C and -40 to +105 °C
temperature ranges, at a 1.8 V ± 8% power supply. A comprehensive set of power-saving
modes allows the design of low-power applications.
The STM32F048x6 microcontrollers include devices in three different packages ranging
from 36 pins to 48 pins with a die form also available upon request. Depending on the
device chosen, different sets of peripherals are included.
These features make the STM32F048x6 microcontrollers suitable for a wide range of
applications such as application control and user interfaces, hand-held equipment, A/V
receivers and digital TV, PC peripherals, gaming and GPS platforms, industrial applications,
PLCs, inverters, printers, scanners, alarm systems, video intercoms and HVACs.
DocID026007 Rev 6
9/98
25
Description
STM32F048C6 STM32F048G6 STM32F048T6
Table 1. STM32F048x device features and peripheral counts
Peripheral
STM32F048G6
STM32F048T6
STM32F048C6
Flash memory (Kbyte)
SRAM (Kbyte)
Advanced
32
6
1 (16-bit)
control
Timers
4 (16-bit)
1 (32-bit)
General
purpose
SPI [I2S](1)
I2C
1 [1]
2 [1]
1
2
1
1
Comm.
interfaces
USART
USB
CEC
12-bit ADC
1
(number of channels)
(10 ext. + 3 int.)
GPIOs
23
10
29
13
37
13
Capacitive sensing channels
Max. CPU frequency
Operating voltage
48 MHz
V
DD = 1.8 V ± 8%, VDDA = from VDD to 3.6 V
Ambient operating temperature: -40°C to 85 °C / -40°C to 105°C
Junction temperature: -40°C to 105°C / -40°C to 125°C
Operating temperature
Packages
UFQFPN28
WLCSP36
UFQFPN48
1. The SPI1 interface can be used either in SPI mode or in I2S audio mode.
10/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Description
Figure 1. Block diagram
6:&/.ꢄ
6:',2
DVꢄ$)
6HULDOꢄ:LUHꢄ
'HEXJ
9''ꢄ ꢄꢌꢇꢃꢄ9ꢄꢃꢑ
966ꢄ
32:(5
9''ꢌꢃ
)ODVKꢄ*3/ꢄ
ꢀꢆꢄ.%ꢄ
#ꢄ9''
&257(;ꢓ0ꢎꢄ&38ꢄ
I0$;ꢄ ꢄꢁꢃꢄ0+]
ꢀꢆꢓELW
6833/<ꢄ
683(59,6,21
325
5HVHW
,QW
1325
1567
9''$ꢄ
65$0ꢄ
ꢒꢄ.%
1325
19,&
#ꢄ9''$
966$
+6,ꢌꢁ
+6,
5&ꢄꢌꢁꢄ0+]
5&ꢄꢃꢄ0+]
3//
#ꢄ9''$
3//&/.
/6,
#ꢄ9''
*3ꢄ'0$ꢄ
ꢍꢄFKDQQHOV
;7$/ꢄ26&ꢄ
ꢁꢓꢀꢆꢄ0+]
5&ꢄꢁꢎꢄN+]
5&ꢄꢁꢃ0+]
26&B,1
26&B287
+6,ꢁꢃ
,QGꢇꢄ:LQGRZꢄ:'*
325
3$>ꢌꢍꢅꢎ@
3%>ꢌꢍꢅꢎ@
3&>ꢌꢍꢅꢌꢀ@
*3,2ꢄSRUWꢄ$
*3,2ꢄSRUWꢄ%
*3,2ꢄSRUWꢄ&
9''
5(6(7ꢄꢔꢄ&/2&.ꢄ
&21752/
9%$7ꢄ ꢄꢌꢇꢒꢍꢄWRꢄꢀꢇꢒꢄ9
#ꢄ9%$7
26&ꢀꢆB,1ꢄ
26&ꢀꢆB287
;7$/ꢀꢆꢄN+]
%DFNXSꢄ
6\VWHPꢄDQGꢄSHULSKHUDOꢄ
FORFNV
ꢌꢄ7$03(5ꢓ57&
ꢉ$/$50ꢄ287ꢋ
57&
UHJ
57&ꢄLQWHUIDFH
&56
&5&
3)>ꢌꢌꢈꢌꢅꢎ@
*3,2ꢄSRUWꢄ)
3$'ꢄ
6<1&
ꢁꢄFKDQQHOV
ꢀꢄFRPSOꢇꢄFKDQQHOV
%5.ꢈꢄ(75ꢄLQSXWꢄDVꢄ$)
3:0ꢄ7,0(5ꢄꢌ
7,0(5ꢄꢆꢄꢀꢆꢓELW
7,0(5ꢄꢀ
ꢍꢄJURXSVꢄRIꢄ
ꢁꢄFKDQQHOV
7RXFK
$QDORJꢄ
6HQVLQJꢄꢄ
&RQWUROOHU
VZLWFKHV
$+%
$3%
ꢁꢄFKꢇꢈꢄ(75ꢄDVꢄ$)
ꢁꢄFKꢇꢈꢄ(75ꢄDVꢄ$)
ꢌꢄFKDQQHOꢄDVꢄ$)
6<1&
ꢀꢏꢄ$)
(;7ꢇꢄ,7ꢄꢄ:.83
7,0(5ꢄꢌꢁ
86%ꢄ
86%
3+<
'ꢊꢈꢄ'ꢓ
ꢌꢄFKDQQHO
#ꢄ9'',2ꢆ
7,0(5ꢄꢌꢒ
7,0(5ꢄꢌꢏ
ꢌꢄFRPSOꢈꢄ%5.ꢄDVꢄ$)
65$0
ꢌꢎꢆꢁꢄ%
ꢌꢄFKDQQHO
ꢌꢄFRPSOꢈꢄ%5.ꢄDVꢄ$)
:LQGRZꢄ:'*
'%*0&8
,5B287ꢄDVꢄ$)
5;ꢈꢄ7;ꢈ&76ꢈꢄ576ꢈꢄ
&.ꢄDVꢄ$)
026,ꢐ6'ꢄ
0,62ꢐ0&.ꢄ
6&.ꢐ&.ꢄ
86$57ꢌ
86$57ꢆ
63,ꢌꢐ,ꢆ6ꢌ
63,ꢆ
5;ꢈꢄ7;ꢈ&76ꢈꢄ576ꢈꢄ
&.ꢄDVꢄ$)
6<6&)*ꢄ,)
166ꢐ:6ꢄDVꢄ$)
026,ꢄ
0,62ꢄ
6&.ꢄ
6&/ꢈꢄ6'$ꢈꢄ60%$ꢄ
ꢉH[WUDꢄP$ꢄ)0ꢊꢋꢄDVꢄ$)
,ꢆ&ꢌ
166ꢄDVꢄ$)
7HPSꢇꢄ
VHQVRU
+'0,ꢓ&(&
&(&ꢄDVꢄ$)
ꢌꢎ[ꢄꢄ
$'ꢄLQSXW
ꢌꢆꢓELWꢄ$'& ,)
9''$
966$
#ꢄ9''$
3RZHUꢄGRPDLQꢄRIꢄDQDORJꢄEORFNVꢄꢅ
9%$7
9''
9''$
9'',2ꢆ
06Yꢀꢁꢂꢃꢁ9ꢀ
DocID026007 Rev 6
11/98
25
Functional overview
STM32F048C6 STM32F048G6 STM32F048T6
3
Functional overview
Figure 1 shows the general block diagram of the STM32F048x6 devices.
3.1
ARM®-Cortex®-M0 core
®
®
The ARM Cortex -M0 is a generation of ARM 32-bit RISC processors for embedded
systems. It has been developed to provide a low-cost platform that meets the needs of MCU
implementation, with a reduced pin count and low-power consumption, while delivering
outstanding computational performance and an advanced system response to interrupts.
®
®
The ARM Cortex -M0 processors feature exceptional code-efficiency, delivering the high
performance expected from an ARM core, with memory sizes usually associated with 8- and
16-bit devices.
The STM32F048x6 devices embed ARM core and are compatible with all ARM tools and
software.
3.2
Memories
The device has the following features:
•
6 Kbytes of embedded SRAM accessed (read/write) at CPU clock speed with 0 wait
states and featuring embedded parity checking with exception generation for fail-critical
applications.
•
The non-volatile memory is divided into two arrays:
–
–
32 Kbytes of embedded Flash memory for programs and data
Option bytes
The option bytes are used to write-protect the memory (with 4 KB granularity) and/or
readout-protect the whole memory with the following options:
–
–
Level 0: no readout protection
Level 1: memory readout protection, the Flash memory cannot be read from or
written to if either debug features are connected or boot in RAM is selected
®
–
Level 2: chip readout protection, debug features (Cortex -M0 serial wire) and
boot in RAM selection disabled
3.3
Boot modes
At startup, the boot pin and boot selector option bits are used to select one of the three boot
options:
•
•
•
boot from User Flash memory
boot from System Memory
boot from embedded SRAM
The boot pin is shared with the standard GPIO and can be disabled through the boot
selector option bits. The boot loader is located in System Memory. It is used to reprogram
2
the Flash memory by using USART on pins PA14/PA15 or PA9/PA10 or I C on pins
PB6/PB7 or through the USB DFU interface.
12/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Functional overview
3.4
Cyclic redundancy check calculation unit (CRC)
The CRC (cyclic redundancy check) calculation unit is used to get a CRC code from a 32-bit
data word and a CRC-32 (Ethernet) polynomial.
Among other applications, CRC-based techniques are used to verify data transmission or
storage integrity. In the scope of the EN/IEC 60335-1 standard, they offer a means of
verifying the Flash memory integrity. The CRC calculation unit helps compute a signature of
the software during runtime, to be compared with a reference signature generated at link-
time and stored at a given memory location.
3.5
Power management
3.5.1
Power supply schemes
•
V
= V
= 1.8 V ± 8%: external power supply for I/Os (V
) and digital logic. It
DD
DDIO1
DDIO1
is provided externally through VDD pins.
•
V
= from V to 3.6 V: external analog power supply for ADC, RCs and PLL
DDA
DD
(minimum voltage to be applied to V
externally through VDDA pin. The V
is 2.4 V when the ADC is used). It is provided
voltage level must be always greater or equal
DDA
DDA
to the V voltage level and must be established first.
DD
•
•
V
= 1.65 to 3.6 V: external power supply for marked I/Os. V
is provided
DDIO2
DDIO2
externally through the VDDIO2 pin. The V
from V or V
V
(V
are disabled by hardware. The output of this comparator is connected to EXTI line 31
and it can be used to generate an interrupt. Refer to the pinout diagrams or tables for
concerned I/Os list.
voltage level is completely independent
DDIO2
, but it must not be provided without a valid supply on V . The
DD
DDA
DD
supply is monitored and compared with the internal reference voltage
DDIO2
). When the V
is below this threshold, all the I/Os supplied from this rail
REFINT
DDIO2
V
= 1.65 to 3.6 V: power supply for RTC, external clock 32 kHz oscillator and
BAT
backup registers (through power switch) when V is not present.
DD
For more details on how to connect power pins, refer to Figure 9: Power supply scheme.
3.5.2
3.5.3
Power-on reset
To guarantee a proper power-on reset, the NPOR pin must be held low until V is stable.
DD
When V is stable, the reset state can be exited either by:
DD
•
•
putting the NPOR pin in high impedance (NPOR pin has an internal pull-up), or by
forcing the pin to high level by connecting it to V
DDA
Low-power modes
The STM32F048x6 microcontrollers support two low-power modes to achieve the best
compromise between low power consumption, short startup time and available wakeup
sources:
•
Sleep mode
In Sleep mode, only the CPU is stopped. All peripherals continue to operate and can
wake up the CPU when an interrupt/event occurs.
DocID026007 Rev 6
13/98
25
Functional overview
STM32F048C6 STM32F048G6 STM32F048T6
•
Stop mode
Stop mode achieves very low power consumption while retaining the content of SRAM
and registers. All clocks in the 1.8 V domain are stopped, the PLL, the HSI RC and the
HSE crystal oscillators are disabled.
The device can be woken up from Stop mode by any of the EXTI lines. The EXTI line
source can be one of the 16 external lines, RTC, I2C1, USART1, USART2, USB,
V
supply comparator or the CEC.
DDIO2
The CEC, USART1 and I2C1 peripherals can be configured to enable the HSI RC
oscillator so as to get clock for processing incoming data.
Note:
The RTC, the IWDG, and the corresponding clock sources are not stopped by entering Stop
mode.
3.6
Clocks and startup
System clock selection is performed on startup, however the internal RC 8 MHz oscillator is
selected as default CPU clock on reset. An external 4-32 MHz clock can be selected, in
which case it is monitored for failure. If failure is detected, the system automatically switches
back to the internal RC oscillator. A software interrupt is generated if enabled. Similarly, full
interrupt management of the PLL clock entry is available when necessary (for example on
failure of an indirectly used external crystal, resonator or oscillator).
Several prescalers allow the application to configure the frequency of the AHB and the APB
domains. The maximum frequency of the AHB and the APB domains is 48 MHz.
Additionally, also the internal RC 48 MHz oscillator can be selected for system clock or PLL
input source. This oscillator can be automatically fine-trimmed by the means of the CRS
peripheral using the external synchronization.
14/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Functional overview
Figure 2. Clock tree
)ODVKꢄPHPRU\ꢄ
SURJUDPPLQJꢄ
LQWHUIDFH
86%ꢄ62)
)/,7)&/.
6<1&
/6(
6<1&65&
,ꢆ&ꢌ6:
+6,
,ꢆ&ꢌ
,ꢆ6ꢌ
6<6&/.
&56
+6,
7ULP
+6,ꢁꢃ
+6,ꢁꢃ
+6,
ꢁꢃꢄ0+]
+6,ꢄ5&
&(&6:
/6(
ꢐꢆꢁꢁ
&(&
ꢃꢄ0+]
+6,ꢄ5&
$+%ꢈꢄFRUHꢈꢄPHPRU\ꢈꢄ'0$ꢈꢄ
&RUWH[ꢄ)&/.ꢄIUHHꢓUXQꢄFORFN
+&/.
ꢐꢃ
6:
35(',9
3//65&
6<6&/.
&RUWH[ꢄ
V\VWHPꢄWLPHUꢄ
+6,ꢁꢃ
3//08/
+6,
3//&/.
+6(
3&/.
$3%ꢄ
ꢐꢌꢈꢐꢆꢈ«
ꢐꢌꢈꢐꢆꢈꢐꢁꢈ
ꢐꢃꢈꢐꢌꢒ
3//
[ꢆꢈ[ꢀꢈꢇꢇ
ꢇꢇꢇ[ꢌꢒ
ꢐꢌꢈꢐꢆꢈꢇꢇꢄ
«ꢐꢍꢌꢆ
SHULSKHUDOV
ꢇꢇꢐꢌꢒ
+35(
335(
335(
[ꢌꢈꢄ[ꢆ
&66
7,0ꢌꢈꢆꢈꢀꢈ
ꢌꢁꢈꢌꢒꢈꢌꢏ
26&B287
26&B,1
+6(
ꢁꢓꢀꢆꢄ0+]
+6(ꢄ26&
86$57ꢌ6:
3&/.
/6(
6<6&/.
+6,
86$57ꢌ
57&
ꢐꢀꢆ
/6(
/6(
57&&/.
26&ꢀꢆB,1
ꢀꢆꢇꢏꢒꢃꢄN+]
/6(ꢄ26&
86%6:
26&ꢀꢆB287
+6,ꢁꢃ
3//&/.
57&6(/
86%
/6,
ꢁꢎꢄN+]
/6,ꢄ5&
,:'*
3//12',9
ꢐꢌꢈꢐꢆ
$'&ꢄ
ꢌꢁꢄ0+]ꢄ5&
+6,ꢌꢁ
+6,ꢌꢁ
DV\QFKURQRXVꢄ
FORFNꢄLQSXW
3//&/.
+6,ꢁꢃ
+6(
0&235(
+6,
0DLQꢄFORFN
RXWSXW
ꢐꢌꢈꢐꢆꢈꢐꢁꢈꢇꢇ
ꢇꢇꢐꢌꢆꢃ
+6,ꢌꢁ
6<6&/.
/6(
0&2
/HJHQG
EODFN
ZKLWH
FORFNꢄWUHHꢄHOHPHQW
/6,
FORFNꢄWUHHꢄFRQWUROꢄHOHPHQW
FORFNꢄOLQH
WRꢄ7,0ꢌꢁ
0&2
FRQWUROꢄOLQH
06Yꢀꢀꢌꢏꢂ9ꢁ
3.7
General-purpose inputs/outputs (GPIOs)
Each of the GPIO pins can be configured by software as output (push-pull or open-drain), as
input (with or without pull-up or pull-down) or as peripheral alternate function. Most of the
GPIO pins are shared with digital or analog alternate functions.
DocID026007 Rev 6
15/98
25
Functional overview
STM32F048C6 STM32F048G6 STM32F048T6
The I/O configuration can be locked if needed following a specific sequence in order to
avoid spurious writing to the I/Os registers.
3.8
Direct memory access controller (DMA)
The 5-channel general-purpose DMAs manage memory-to-memory, peripheral-to-memory
and memory-to-peripheral transfers.
The DMA supports circular buffer management, removing the need for user code
intervention when the controller reaches the end of the buffer.
Each channel is connected to dedicated hardware DMA requests, with support for software
trigger on each channel. Configuration is made by software and transfer sizes between
source and destination are independent.
DMA can be used with the main peripherals: SPIx, I2Sx, I2Cx, USARTx, all TIMx timers
(except TIM14) and ADC.
3.9
Interrupts and events
3.9.1
Nested vectored interrupt controller (NVIC)
The STM32F0xx family embeds a nested vectored interrupt controller able to handle up to
®
32 maskable interrupt channels (not including the 16 interrupt lines of Cortex -M0) and 4
priority levels.
•
•
•
•
•
•
•
•
Closely coupled NVIC gives low latency interrupt processing
Interrupt entry vector table address passed directly to the core
Closely coupled NVIC core interface
Allows early processing of interrupts
Processing of late arriving higher priority interrupts
Support for tail-chaining
Processor state automatically saved
Interrupt entry restored on interrupt exit with no instruction overhead
This hardware block provides flexible interrupt management features with minimal interrupt
latency.
3.9.2
Extended interrupt/event controller (EXTI)
The extended interrupt/event controller consists of 24 edge detector lines used to generate
interrupt/event requests and wake-up the system. Each line can be independently
configured to select the trigger event (rising edge, falling edge, both) and can be masked
independently. A pending register maintains the status of the interrupt requests. The EXTI
can detect an external line with a pulse width shorter than the internal clock period. Up to 37
GPIOs can be connected to the 16 external interrupt lines.
3.10
Analog-to-digital converter (ADC)
The 12-bit analog-to-digital converter has up to 10 external and 3 internal (temperature
16/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Functional overview
sensor, voltage reference, VBAT voltage measurement) channels and performs conversions
in single-shot or scan modes. In scan mode, automatic conversion is performed on a
selected group of analog inputs.
The ADC can be served by the DMA controller.
An analog watchdog feature allows very precise monitoring of the converted voltage of one,
some or all selected channels. An interrupt is generated when the converted voltage is
outside the programmed thresholds.
3.10.1
Temperature sensor
The temperature sensor (TS) generates a voltage V
temperature.
that varies linearly with
SENSE
The temperature sensor is internally connected to the ADC_IN16 input channel which is
used to convert the sensor output voltage into a digital value.
The sensor provides good linearity but it has to be calibrated to obtain good overall
accuracy of the temperature measurement. As the offset of the temperature sensor varies
from chip to chip due to process variation, the uncalibrated internal temperature sensor is
suitable for applications that detect temperature changes only.
To improve the accuracy of the temperature sensor measurement, each device is
individually factory-calibrated by ST. The temperature sensor factory calibration data are
stored by ST in the system memory area, accessible in read-only mode.
Table 2. Temperature sensor calibration values
Calibration value name
Description
Memory address
TS ADC raw data acquired at a
temperature of 30 °C (± 5 °C),
VDDA= 3.3 V (± 10 mV)
TS_CAL1
0x1FFF F7B8 - 0x1FFF F7B9
TS ADC raw data acquired at a
temperature of 110 °C (± 5 °C),
TS_CAL2
0x1FFF F7C2 - 0x1FFF F7C3
VDDA= 3.3 V (± 10 mV)
3.10.2
Internal voltage reference (V
)
REFINT
The internal voltage reference (V
) provides a stable (bandgap) voltage output for the
REFINT
ADC. V
is internally connected to the ADC_IN17 input channel. The precise voltage
REFINT
of V
is individually measured for each part by ST during production test and stored in
REFINT
the system memory area. It is accessible in read-only mode.
Table 3. Internal voltage reference calibration values
Calibration value name
Description
Memory address
Raw data acquired at a
VREFINT_CAL
temperature of 30 °C (± 5 °C),
0x1FFF F7BA - 0x1FFF F7BB
VDDA= 3.3 V (± 10 mV)
DocID026007 Rev 6
17/98
25
Functional overview
STM32F048C6 STM32F048G6 STM32F048T6
3.10.3
V
battery voltage monitoring
BAT
This embedded hardware feature allows the application to measure the V
battery voltage
BAT
using the internal ADC channel ADC_IN18. As the V
voltage may be higher than V
,
BAT
DDA
and thus outside the ADC input range, the V
pin is internally connected to a bridge
BAT
divider by 2. As a consequence, the converted digital value is half the V
voltage.
BAT
3.11
Touch sensing controller (TSC)
The STM32F048x6 devices provide a simple solution for adding capacitive sensing
functionality to any application. These devices offer up to 13 capacitive sensing channels
distributed over 5 analog I/O groups.
Capacitive sensing technology is able to detect the presence of a finger near a sensor which
is protected from direct touch by a dielectric (glass, plastic...). The capacitive variation
introduced by the finger (or any conductive object) is measured using a proven
implementation based on a surface charge transfer acquisition principle. It consists in
charging the sensor capacitance and then transferring a part of the accumulated charges
into a sampling capacitor until the voltage across this capacitor has reached a specific
threshold. To limit the CPU bandwidth usage, this acquisition is directly managed by the
hardware touch sensing controller and only requires few external components to operate.
For operation, one capacitive sensing GPIO in each group is connected to an external
capacitor and cannot be used as effective touch sensing channel.
The touch sensing controller is fully supported by the STMTouch touch sensing firmware
library, which is free to use and allows touch sensing functionality to be implemented reliably
in the end application.
Table 4. Capacitive sensing GPIOs available on STM32F048x6 devices
Capacitive sensing
signal name
Pin
name
Capacitive sensing
signal name
Pin
name
Group
Group
TSC_G1_IO1
TSC_G1_IO2
TSC_G1_IO3
TSC_G1_IO4
TSC_G2_IO1
TSC_G2_IO2
TSC_G2_IO3
TSC_G2_IO4
TSC_G3_IO2
TSC_G3_IO3
TSC_G3_IO4
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
PB0
PB1
PB2
TSC_G4_IO1
TSC_G4_IO2
TSC_G4_IO3
TSC_G4_IO4
TSC_G5_IO1
TSC_G5_IO2
TSC_G5_IO3
TSC_G5_IO4
PA9
PA10
PA11
PA12
PB3
1
4
PB4
2
3
5
PB6
PB7
18/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Functional overview
Table 5. No. of capacitive sensing channels available on STM32F048x6 devices
Number of capacitive sensing channels
Analog I/O group
STM32F048C6
UQFPN48
STM32F048T6
WLCSP36
STM32F048G6
UQFPN28
G1
G2
G3
G4
G5
3
3
1
3
3
3
3
1
3
3
3
3
0
1
3
Number of capacitive sensing
channels
13
13
10
3.12
Timers and watchdogs
The STM32F048x6 devices include up to five general-purpose timers and an advanced
control timer.
Table 6 compares the features of the different timers.
Table 6. Timer feature comparison
DMA
Timer
type
Counter
resolution
Counter
type
Prescaler
factor
Capture/compare Complementary
Timer
request
generation
channels
outputs
Advanced
control
Up, down, integer from
up/down 1 to 65536
TIM1
TIM2
TIM3
TIM14
16-bit
32-bit
16-bit
16-bit
16-bit
Yes
Yes
Yes
No
4
4
4
1
1
3
-
Up, down, integer from
up/down 1 to 65536
Up, down, integer from
-
up/down
1 to 65536
General
purpose
integer from
1 to 65536
Up
-
TIM16
TIM17
integer from
1 to 65536
Up
Yes
1
3.12.1
Advanced-control timer (TIM1)
The advanced-control timer (TIM1) can be seen as a three-phase PWM multiplexed on six
channels. It has complementary PWM outputs with programmable inserted dead times. It
DocID026007 Rev 6
19/98
25
Functional overview
STM32F048C6 STM32F048G6 STM32F048T6
can also be seen as a complete general-purpose timer. The four independent channels can
be used for:
•
•
•
•
input capture
output compare
PWM generation (edge or center-aligned modes)
one-pulse mode output
If configured as a standard 16-bit timer, it has the same features as the TIMx timer. If
configured as the 16-bit PWM generator, it has full modulation capability (0-100%).
The counter can be frozen in debug mode.
Many features are shared with those of the standard timers which have the same
architecture. The advanced control timer can therefore work together with the other timers
via the Timer Link feature for synchronization or event chaining.
3.12.2
General-purpose timers (TIM2, 3, 14, 16, 17)
There are five synchronizable general-purpose timers embedded in the STM32F048x6
devices (see Table 6 for differences). Each general-purpose timer can be used to generate
PWM outputs, or as simple time base.
TIM2, TIM3
STM32F048x6 devices feature two synchronizable 4-channel general-purpose timers. TIM2
is based on a 32-bit auto-reload up/downcounter and a 16-bit prescaler. TIM3 is based on a
16-bit auto-reload up/downcounter and a 16-bit prescaler. They feature 4 independent
channels each for input capture/output compare, PWM or one-pulse mode output. This
gives up to 12 input captures/output compares/PWMs on the largest packages.
The TIM2 and TIM3 general-purpose timers can work together or with the TIM1 advanced-
control timer via the Timer Link feature for synchronization or event chaining.
TIM2 and TIM3 both have independent DMA request generation.
These timers are capable of handling quadrature (incremental) encoder signals and the
digital outputs from 1 to 3 hall-effect sensors.
Their counters can be frozen in debug mode.
TIM14
This timer is based on a 16-bit auto-reload upcounter and a 16-bit prescaler.
TIM14 features one single channel for input capture/output compare, PWM or one-pulse
mode output.
Its counter can be frozen in debug mode.
TIM16 and TIM17
Both timers are based on a 16-bit auto-reload upcounter and a 16-bit prescaler.
They each have a single channel for input capture/output compare, PWM or one-pulse
mode output.
20/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Functional overview
TIM16 and TIM17 have a complementary output with dead-time generation and
independent DMA request generation.
Their counters can be frozen in debug mode.
3.12.3
Independent watchdog (IWDG)
The independent watchdog is based on an 8-bit prescaler and 12-bit downcounter with
user-defined refresh window. It is clocked from an independent 40 kHz internal RC and as it
operates independently from the main clock, it can operate in Stop mode. It can be used
either as a watchdog to reset the device when a problem occurs, or as a free running timer
for application timeout management. It is hardware or software configurable through the
option bytes. The counter can be frozen in debug mode.
3.12.4
3.12.5
System window watchdog (WWDG)
The system window watchdog is based on a 7-bit downcounter that can be set as free
running. It can be used as a watchdog to reset the device when a problem occurs. It is
clocked from the APB clock (PCLK). It has an early warning interrupt capability and the
counter can be frozen in debug mode.
SysTick timer
This timer is dedicated to real-time operating systems, but could also be used as a standard
down counter. It features:
•
•
•
•
a 24-bit down counter
autoreload capability
maskable system interrupt generation when the counter reaches 0
programmable clock source (HCLK or HCLK/8)
3.13
Real-time clock (RTC) and backup registers
The RTC and the five backup registers are supplied through a switch that takes power either
on V supply when present or through the V
pin. The backup registers are five 32-bit
DD
BAT
registers used to store 20 bytes of user application data when V power is not present.
DD
They are not reset by a system or power reset.
DocID026007 Rev 6
21/98
25
Functional overview
STM32F048C6 STM32F048G6 STM32F048T6
The RTC is an independent BCD timer/counter. Its main features are the following:
•
calendar with subseconds, seconds, minutes, hours (12 or 24 format), week day, date,
month, year, in BCD (binary-coded decimal) format
•
•
•
automatic correction for 28, 29 (leap year), 30, and 31 day of the month
programmable alarm with wake up from Stop mode capability
on-the-fly correction from 1 to 32767 RTC clock pulses. This can be used to
synchronize the RTC with a master clock
•
•
•
digital calibration circuit with 1 ppm resolution, to compensate for quartz crystal
inaccuracy
two anti-tamper detection pins with programmable filter. The MCU can be woken up
from Stop mode on tamper event detection
timestamp feature which can be used to save the calendar content. This function can
be triggered by an event on the timestamp pin, or by a tamper event. The MCU can be
woken up from Stop mode on timestamp event detection
•
reference clock detection: a more precise second source clock (50 or 60 Hz) can be
used to enhance the calendar precision
The RTC clock sources can be:
•
•
•
•
a 32.768 kHz external crystal
a resonator or oscillator
the internal low-power RC oscillator (typical frequency of 40 kHz)
the high-speed external clock divided by 32
3.14
Inter-integrated circuit interface (I2C)
2
The I C interface (I2C1) can operate in multimaster or slave modes. It can support Standard
mode (up to 100 kbit/s), Fast mode (up to 400 kbit/s) and Fast Mode Plus (up to 1 Mbit/s)
with extra output drive.
It supports 7-bit and 10-bit addressing modes, multiple 7-bit slave addresses (two
addresses, one with configurable mask). It also includes programmable analog and digital
noise filters.
2
Table 7. Comparison of I C analog and digital filters
Aspect
Analog filter
Digital filter
Pulse width of
suppressed spikes
Programmable length from 1 to 15
I2Cx peripheral clocks
≥ 50 ns
–Extra filtering capability vs.
standard requirements
Benefits
Available in Stop mode
–Stable length
Wakeup from Stop on address
match is not available when digital
filter is enabled.
Variations depending on
temperature, voltage, process
Drawbacks
In addition, I2C1 provides hardware support for SMBUS 2.0 and PMBUS 1.1: ARP
capability, Host notify protocol, hardware CRC (PEC) generation/verification, timeouts
verifications and ALERT protocol management. I2C1 also has a clock domain independent
22/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Functional overview
from the CPU clock, allowing the I2C1 to wake up the MCU from Stop mode on address
match.
The I2C peripheral can be served by the DMA controller.
2
Table 8. STM32F048x6 I C implementation
I2C features(1)
I2C1
7-bit addressing mode
X
X
X
X
X
X
X
X
10-bit addressing mode
Standard mode (up to 100 kbit/s)
Fast mode (up to 400 kbit/s)
Fast Mode Plus with extra output drive I/Os (up to 1 Mbit/s)
Independent clock
SMBus
Wakeup from STOP
1. X = supported.
3.15
Universal synchronous/asynchronous receiver/transmitter
(USART)
The device embeds two universal synchronous/asynchronous receivers/transmitters
(USART1, USART2) which communicate at speeds of up to 6 Mbit/s.
They provide hardware management of the CTS, RTS and RS485 DE signals,
multiprocessor communication mode, master synchronous communication and single-wire
half-duplex communication mode. USART1 supports also SmartCard communication (ISO
7816), IrDA SIR ENDEC, LIN Master/Slave capability and auto baud rate feature, and has a
clock domain independent of the CPU clock, allowing to wake up the MCU from Stop mode.
The USART interfaces can be served by the DMA controller.
Table 9. STM32F048x6 USART implementation
USART modes/features(1)
USART1
USART2
Hardware flow control for modem
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
Continuous communication using DMA
Multiprocessor communication
Synchronous mode
Smartcard mode
Single-wire half-duplex communication
IrDA SIR ENDEC block
X
-
LIN mode
-
Dual clock domain and wakeup from Stop mode
Receiver timeout interrupt
-
-
DocID026007 Rev 6
23/98
25
Functional overview
STM32F048C6 STM32F048G6 STM32F048T6
Table 9. STM32F048x6 USART implementation (continued)
USART modes/features(1)
USART1
USART2
Modbus communication
X
X
X
-
-
Auto baud rate detection
Driver Enable
X
1. X = supported.
3.16
Serial peripheral interface (SPI) / Inter-integrated sound
interface (I2S)
Up to two SPIs are able to communicate up to 18 Mbit/s in slave and master modes in full-
duplex and half-duplex communication modes. The 3-bit prescaler gives 8 master mode
frequencies and the frame size is configurable from 4 bits to 16 bits.
2
One standard I S interface (multiplexed with SPI1) supporting four different audio standards
can operate as master or slave at half-duplex communication mode. It can be configured to
transfer 16 and 24 or 32 bits with 16-bit or 32-bit data resolution and synchronized by a
specific signal. Audio sampling frequency from 8 kHz up to 192 kHz can be set by an 8-bit
programmable linear prescaler. When operating in master mode, it can output a clock for an
external audio component at 256 times the sampling frequency.
2
Table 10. STM32F048x6 SPI/I S implementation
SPI features(1)
SPI1
SPI2
Hardware CRC calculation
X
X
X
X
X
X
X
X
-
Rx/Tx FIFO
NSS pulse mode
I2S mode
TI mode
X
1. X = supported.
3.17
High-definition multimedia interface (HDMI) - consumer
electronics control (CEC)
The device embeds a HDMI-CEC controller that provides hardware support for the
Consumer Electronics Control (CEC) protocol (Supplement 1 to the HDMI standard).
This protocol provides high-level control functions between all audiovisual products in an
environment. It is specified to operate at low speeds with minimum processing and memory
overhead. It has a clock domain independent from the CPU clock, allowing the HDMI_CEC
controller to wakeup the MCU from Stop mode on data reception.
3.18
Universal serial bus (USB)
The STM32F048x6 embeds a full-speed USB device peripheral compliant with the USB
specification version 2.0. The internal USB PHY supports USB FS signaling, embedded DP
24/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Functional overview
pull-up and also battery charging detection according to Battery Charging Specification
Revision 1.2. The USB interface implements a full-speed (12 Mbit/s) function interface with
added support for USB 2.0 Link Power Management. It has software-configurable endpoint
setting with packet memory up-to 1 KB and suspend/resume support. It requires a precise
48 MHz clock which can be generated from the internal main PLL (the clock source must
use an HSE crystal oscillator) or by the internal 48 MHz oscillator in automatic trimming
mode. The synchronization for this oscillator can be taken from the USB data stream itself
(SOF signalization) which allows crystal-less operation.
3.19
3.20
Clock recovery system (CRS)
The STM32F048x6 embeds a special block which allows automatic trimming of the internal
48 MHz oscillator to guarantee its optimal accuracy over the whole device operational
range. This automatic trimming is based on the external synchronization signal, which could
be either derived from USB SOF signalization, from LSE oscillator, from an external signal
on CRS_SYNC pin or generated by user software. For faster lock-in during startup it is also
possible to combine automatic trimming with manual trimming action.
Serial wire debug port (SW-DP)
An ARM SW-DP interface is provided to allow a serial wire debugging tool to be connected
to the MCU.
DocID026007 Rev 6
25/98
25
Pinouts and pin descriptions
STM32F048C6 STM32F048G6 STM32F048T6
4
Pinouts and pin descriptions
Figure 3. UFQFPN48 package pinout
7RSꢄYLHZ
9%$7
3&ꢌꢀ
ꢌ
ꢆ
ꢀꢒ
ꢀꢍ
ꢀꢁ
ꢀꢀ
ꢀꢆ
ꢀꢌ
ꢀꢎ
ꢆꢂ
ꢆꢃ
ꢆꢏ
ꢆꢒ
ꢆꢍ
9'',2ꢆ
966
3&ꢌꢁꢓ26&ꢀꢆB,1
3&ꢌꢍꢓ26&ꢀꢆB287
3)ꢎꢓ26&B,1
3)ꢌꢓ26&B287
1567
ꢀ
3$ꢌꢀ
3$ꢌꢆ
3$ꢌꢌ
3$ꢌꢎ
3$ꢂ
ꢁ
ꢍ
ꢒ
8)4)31ꢁꢃ
ꢏ
966$
ꢃ
3$ꢃ
9''$
ꢂ
3%ꢌꢍ
3%ꢌꢁ
3%ꢌꢀ
3%ꢌꢆ
3$ꢎ
ꢌꢎ
ꢌꢌ
ꢌꢆ
([SRVHGꢄSDG
3$ꢌ
3$ꢆ
,ꢐ2ꢄVXSSOLHGꢄIURPꢄ9'',2ꢆ
06Yꢀꢒꢁꢎꢁ9ꢆ
Figure 4. WLCSP36 package
7RSꢄYLHZ
ꢌ
ꢆ
ꢀ
ꢁ
ꢍ
ꢒ
3$ꢌꢆ
3$ꢌꢀ
3$ꢌꢎ
3$ꢂ
3$ꢌꢍ
3%ꢁ
3%ꢏ
9''
3)ꢎꢓ
3&ꢌꢀ
$
%
&
'
(
)
3&ꢌꢁꢓ
3%ꢃꢓ
%227ꢎ
26&B 26&ꢀꢆB
3$ꢌꢁ
3$ꢌꢌ
3%ꢆ
3%ꢀ
3$ꢁ
3$ꢍ
3$ꢒ
3%ꢎ
,1
,1
3)ꢌꢓ
3&ꢌꢍꢓ
26&B 26&ꢀꢆB
3%ꢒ
3$ꢌ
3$ꢆ
3$ꢏ
287
287
1567
966
9'',2ꢆ 3$ꢃ
9''$
3$ꢀ
3%ꢍ
3$ꢎ
966
1325
:/&63ꢀꢒ
,ꢐ2ꢄVXSSOLHGꢄIURPꢄ9'',2ꢆ
06Yꢀꢁꢂꢃꢏ9ꢀ
1. The above figure shows the package in top view, changing from bottom view in the previous document
versions.
26/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Pinouts and pin descriptions
Figure 5. UFQFPN28 package
7RSꢄYLHZ
ꢌ
ꢆ
ꢀ
ꢁ
ꢍ
ꢒ
ꢏ
ꢆꢌ
ꢆꢎ
ꢌꢂ
ꢌꢃ
ꢌꢏ
ꢌꢒ
ꢌꢍ
3%ꢃꢓ%227ꢎ
3$ꢌꢀ
3)ꢎꢓ26&B,1
3)ꢌꢓ26&B287
1567
3$ꢌꢎꢄ>3$ꢌꢆ@
3$ꢂꢄ>3$ꢌꢌ@
9'',2ꢆ
9''
966
1325
8)4)31ꢆꢃ
9''$
3$ꢎ
3$ꢌ
,ꢐ2ꢄVXSSOLHGꢄIURPꢄ9'',2ꢆ
06Yꢀꢁꢂꢃꢃ9ꢆ
1. Pin pair PA11/12 can be remapped in place of pin pair PA9/10 using the SYSCFG_CFGR1 register.
Table 11. Legend/abbreviations used in the pinout table
Name
Abbreviation
Definition
Unless otherwise specified in brackets below the pin name, the pin function during and
after reset is the same as the actual pin name
Pin name
S
I
Supply pin
Pin type
Input-only pin
I/O
FT
FTf
TTa
TC
Input / output pin
5 V-tolerant I/O
5 V-tolerant I/O, FM+ capable
3.3 V-tolerant I/O directly connected to ADC
Standard 3.3 V I/O
I/O structure
External power-on reset pin with embedded weak pull-up resistor,
powered from VDDA
POR
RST
Bidirectional reset pin with embedded weak pull-up resistor
Unless otherwise specified by a note, all I/Os are set as floating inputs during and after
reset.
Notes
Alternate
Functions selected through GPIOx_AFR registers
functions
Pin
functions
Additional
functions
Functions directly selected/enabled through peripheral registers
DocID026007 Rev 6
27/98
33
Pinouts and pin descriptions
Pin numbers
STM32F048C6 STM32F048G6 STM32F048T6
Table 12. STM32F048x6 pin definitions
Pin functions
Pin name
(function upon
reset)
Pin
type
Additional
functions
Alternate function
1
2
-
-
-
VBAT
PC13
S
-
-
Backup power supply
WKUP2,
RTC_TAMP1,
RTC_TS,
(1)(2)
A6
I/O
TC
-
RTC_OUT
(1)
(2)
PC14-OSC32_IN
(PC14)
3
4
5
6
7
B6
C6
B5
C5
D5
-
-
I/O
I/O
I/O
I/O
I/O
TC
TC
-
-
OSC32_IN
OSC32_OUT
OSC_IN
(1)
(2)
PC15-OSC32_OUT
(PC15)
CRS_ SYNC
I2C1_SDA
PF0-OSC_IN
(PF0)
2
3
4
FTf
FTf
RST
-
-
PF1-OSC_OUT
(PF1)
I2C1_SCL
OSC_OUT
Device reset input / internal reset output (active
low)
NRST
-
(3)
8
9
D6
E5
16
5
VSSA
VDDA
S
S
Analog ground
-
-
Analog power supply
USART2_CTS,
TIM2_CH1_ETR,
TSC_G1_IO1
RTC_ TAMP2,
WKUP1,
ADC_IN0,
10
F6
6
PA0
I/O
TTa
USART2_RTS, TIM2_CH2,
TSC_G1_IO2,
11
12
13
D4
E4
F5
7
8
9
PA1
PA2
PA3
I/O
I/O
I/O
TTa
TTa
TTa
-
-
-
ADC_IN1
EVENTOUT
USART2_TX, TIM2_CH3,
TSC_G1_IO3
ADC_IN2,
WKUP4
USART2_RX,
TIM2_CH4,
TSC_G1_IO4
ADC_IN3
ADC_IN4
ADC_IN5
ADC_IN6
SPI1_NSS, I2S1_WS,
TIM14_CH1, TSC_G2_IO1,
USART2_CK
14
15
16
C3
D3
E3
10
11
12
PA4
PA5
PA6
I/O
I/O
I/O
TTa
TTa
TTa
-
-
-
USB_NOE
SPI1_SCK, I2S1_CK, CEC,
TIM2_CH1_ETR,
TSC_G2_IO2
SPI1_MISO, I2S1_MCK,
TIM3_CH1, TIM1_BKIN,
TIM16_CH1, TSC_G2_IO3,
EVENTOUT
28/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Pinouts and pin descriptions
Table 12. STM32F048x6 pin definitions (continued)
Pin functions
Pin numbers
Pin name
(function upon
reset)
Pin
type
Additional
functions
Alternate function
SPI1_MOSI, I2S1_SD,
TIM3_CH2, TIM14_CH1,
TIM1_CH1N, TIM17_CH1,
TSC_G2_IO4,
17
F4
13
PA7
I/O
TTa
-
ADC_IN7
ADC_IN8
EVENTOUT
TIM3_CH3, TIM1_CH2N,
TSC_G3_IO2, EVENTOUT
18
19
F3
-
14
-
PB0
PB1
I/O
I/O
TTa
TTa
-
-
TIM3_CH4, TIM14_CH1,
TIM1_CH3N,
ADC_IN9
-
TSC_G3_IO3
-
D2
F2
-
PB2
I/O
I
FT
-
TSC_G3_IO4
(4)
20
15
NPOR
POR
Device power-on reset input
SPI2_SCK, CEC,
TSC_SYNC, TIM2_CH3,
I2C1_SCL
21
22
-
-
-
-
PB10
PB11
I/O
I/O
FTf
FTf
-
-
-
-
TIM2_CH4,
EVENTOUT,
I2C1_SDA
23
24
F1
-
16
17
VSS
VDD
S
S
-
-
-
-
Ground
Digital power supply
TIM1_BKIN, SPI2_NSS,
EVENTOUT
25
26
-
-
-
-
PB12
PB13
I/O
I/O
FT
-
-
-
-
SPI2_SCK,
TIM1_CH1N,
I2C1_SCL
FTf
SPI2_MISO,
TIM1_CH2N,
I2C1_SDA
27
28
29
-
-
-
-
-
PB14
PB15
PA8
I/O
I/O
I/O
FTf
FT
FT
-
-
WKUP7,
RTC_REFIN
-
SPI2_MOSI, TIM1_CH3N
USART1_CK, TIM1_CH1,
EVENTOUT, MCO,
CRS_SYNC
(5)
E2
-
-
-
USART1_TX, TIM1_CH2,
TSC_G4_IO1,
(5)
(5)
30
31
D1
C1
19
20
PA9
I/O
I/O
FTf
FTf
I2C1_SCL
USART1_RX, TIM1_CH3,
TIM17_BKIN, TSC_G4_IO2,
I2C1_SDA
PA10
DocID026007 Rev 6
29/98
33
Pinouts and pin descriptions
STM32F048C6 STM32F048G6 STM32F048T6
Pin functions
Table 12. STM32F048x6 pin definitions (continued)
Pin numbers
Pin name
(function upon
reset)
Pin
type
Additional
Alternate function
functions
USART1_CTS, TIM1_CH4,
TSC_G4_IO3, EVENTOUT,
I2C1_SCL
(5)
32
C2
19(5)
PA11
I/O
FTf
USB_DM
USART1_RTS, TIM1_ETR,
TSC_G4_IO4, EVENTOUT,
I2C1_SDA
(5)
33
34
A1
B1
20(5)
21
PA12
PA13
I/O
I/O
FTf
FT
USB_DP
-
IR_OUT, SWDIO
USB_NOE
(5)(6)
35
36
-
-
VSS
S
S
-
-
-
-
Ground
E1
18
VDDIO2
Digital power supply
(5)
(6)
37
B2
A2
22
23
PA14
PA15
I/O
FT
USART2_TX, SWCLK
-
-
SPI1_NSS, I2S1_WS,
USART2_RX,
TIM2_CH1_ETR,
EVENTOUT,
(5)
38
I/O
FT
USB_NOE
SPI1_SCK, I2S1_CK,
TIM2_CH2, TSC_G5_IO1,
EVENTOUT
39
40
41
B3
A3
E6
24
25
26
PB3
PB4
PB5
I/O
I/O
I/O
FT
FT
FT
-
-
-
-
SPI1_MISO, I2S1_MCK,
TIM17_BKIN, TIM3_CH1,
TSC_G5_IO2, EVENTOUT
-
SPI1_MOSI, I2S1_SD,
I2C1_SMBA, TIM16_BKIN,
TIM3_CH2
WKUP6
I2C1_SCL, USART1_TX,
TIM16_CH1N, TSC_G5_I03
42
43
44
-
C4
A4
-
27
28
-
PB6
PB7
I/O
I/O
I/O
I/O
I/O
FTf
FTf
FTf
FTf
FTf
-
-
-
-
-
-
-
I2C1_SDA, USART1_RX,
TIM17_CH1N, TSC_G5_IO4
Boot memory
selection
PF11-BOOT0
PB8-BOOT0
PB8
-
I2C1_SCL, CEC,
TIM16_CH1, TSC_SYNC
Boot memory
selection
B4
-
1
I2C1_SCL, CEC,
TIM16_CH1, TSC_SYNC
45
-
-
-
SPI2_NSS,
I2C1_SDA, IR_OUT,
TIM17_CH1, EVENTOUT
46
-
-
PB9
I/O
FTf
-
30/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Pinouts and pin descriptions
Table 12. STM32F048x6 pin definitions (continued)
Pin functions
Pin numbers
Pin name
(function upon
reset)
Pin
type
Additional
functions
Alternate function
47
48
-
-
-
VSS
VDD
S
S
-
-
-
-
Ground
A5
Digital power supply
1. PC13, PC14 and PC15 are supplied through the power switch. Since the switch only sinks a limited amount of current
(3 mA), the use of GPIOs PC13 to PC15 in output mode is limited:
- The speed should not exceed 2 MHz with a maximum load of 30 pF.
- These GPIOs must not be used as current sources (e.g. to drive an LED).
2. After the first RTC domain power-up, PC13, PC14 and PC15 operate as GPIOs. Their function then depends on the
content of the RTC registers which are not reset by the system reset. For details on how to manage these GPIOs, refer to
the RTC domain and RTC register descriptions in the reference manual.
3. Distinct VSSA pin is only available on 48-pin packages. On all other packages, the pin number corresponds to the VSS pin
to which VSSA pad of the silicon die is connected.
4. This pin is powered by VDDA
.
5. Pin pair PA11/12 can be remapped instead of pin pair PA9/10 using SYSCFG_CFGR1 register.
6. After reset, these pins are configured as SWDIO and SWCLK alternate functions, and the internal pull-up on the SWDIO
pin and the internal pull-down on the SWCLK pin are activated.
DocID026007 Rev 6
31/98
33
Table 13. Alternate functions selected through GPIOA_AFR registers for port A
Pin name
AF0
AF1
AF2
AF3
AF4
AF5
AF6
AF7
PA0
PA1
-
EVENTOUT
-
USART2_CTS TIM2_CH1_ETR TSC_G1_IO1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
USART2_RTS
USART2_TX
USART2_RX
USART2_CK
CEC
TIM2_CH2
TIM2_CH3
TIM2_CH4
USB_NOE
TSC_G1_IO2
TSC_G1_IO3
TSC_G1_IO4
TSC_G2_IO1
-
-
-
PA2
-
-
-
PA3
-
-
-
-
PA4
SPI1_NSS, I2S1_WS
SPI1_SCK, I2S1_CK
SPI1_MISO, I2S1_MCK
SPI1_MOSI, I2S1_SD
MCO
TIM14_CH1
-
-
PA5
TIM2_CH1_ETR TSC_G2_IO2
-
-
-
PA6
TIM3_CH1
TIM1_BKIN
TIM1_CH1N
TIM1_CH1
TIM1_CH2
TIM1_CH3
TIM1_CH4
TIM1_ETR
USB_NOE
-
TSC_G2_IO3
TSC_G2_IO4
EVENTOUT
TSC_G4_IO1
TSC_G4_IO2
TSC_G4_IO3
TSC_G4_IO4
-
-
TIM16_CH1
EVENTOUT
PA7
TIM3_CH2
TIM14_CH1
TIM17_CH1
EVENTOUT
PA8
USART1_CK
USART1_TX
USART1_RX
USART1_CTS
USART1_RTS
IR_OUT
CRS_SYNC
-
-
-
-
-
-
-
-
-
PA9
-
I2C1_SCL
MCO
PA10
PA11
PA12
PA13
PA14
PA15
TIM17_BKIN
EVENTOUT
EVENTOUT
SWDIO
I2C1_SDA
-
-
-
-
-
-
I2C1_SCL
I2C1_SDA
-
SWCLK
USART2_TX
USART2_RX
-
-
SPI1_NSS, I2S1_WS
TIM2_CH1_ETR EVENTOUT
USB_NOE
Table 14. Alternate functions selected through GPIOB_AFR registers for port B
Pin name
AF0
AF1
AF2
AF3
AF4
AF5
PB0
PB1
EVENTOUT
TIM14_CH1
-
TIM3_CH3
TIM3_CH4
-
TIM1_CH2N
TIM1_CH3N
-
TSC_G3_IO2
TSC_G3_IO3
TSC_G3_IO4
TSC_G5_IO1
TSC_G5_IO2
I2C1_SMBA
TSC_G5_IO3
TSC_G5_IO4
TSC_SYNC
EVENTOUT
TSC_SYNC
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
PB2
-
PB3
SPI1_SCK, I2S1_CK
SPI1_MISO, I2S1_MCK
SPI1_MOSI, I2S1_SD
USART1_TX
USART1_RX
CEC
EVENTOUT
TIM3_CH1
TIM3_CH2
I2C1_SCL
I2C1_SDA
I2C1_SCL
I2C1_SDA
I2C1_SCL
I2C1_SDA
EVENTOUT
-
TIM2_CH2
EVENTOUT
TIM16_BKIN
TIM16_CH1N
TIM17_CH1N
TIM16_CH1
TIM17_CH1
TIM2_CH3
TIM2_CH4
TIM1_BKIN
TIM1_CH1N
TIM1_CH2N
TIM1_CH3N
-
PB4
TIM17_BKIN
PB5
-
PB6
-
PB7
-
PB8
-
PB9
IR_OUT
SPI2_NSS
PB10
PB11
PB12
PB13
PB14
PB15
CEC
SPI2_SCK
EVENTOUT
SPI2_NSS
-
-
-
SPI2_SCK
-
I2C1_SCL
I2C1_SDA
-
SPI2_MISO
SPI2_MOSI
-
-
-
-
Table 15. Alternate functions selected through GPIOF_AFR registers for port F
Pin name
AF0
AF1
PF0
PF1
CRS_SYNC
-
I2C1_SDA
I2C1_SCL
Memory mapping
STM32F048C6 STM32F048G6 STM32F048T6
5
Memory mapping
Figure 6. STM32F048x6 memory map
ꢎ[))))ꢄ))))
ꢎ[ꢁꢃꢎꢎꢄꢌꢏ))
ꢎ[ꢁꢃꢎꢎꢄꢎꢎꢎꢎ
5HVHUYHG
$+%ꢆ
ꢏ
ꢎ[(ꢎꢌꢎꢄꢎꢎꢎꢎ
&RUWH[ꢓ0ꢎꢄLQWHUQDOꢄ
SHULSKHUDOV
ꢎ[(ꢎꢎꢎꢄꢎꢎꢎꢎ
5HVHUYHG
5HVHUYHG
ꢒ
ꢎ[&ꢎꢎꢎꢄꢎꢎꢎꢎ
ꢎ[ꢁꢎꢎꢆꢄꢁꢀ))
ꢎ[ꢁꢎꢎꢆꢄꢎꢎꢎꢎ
$+%ꢌ
5HVHUYHG
ꢍ
5HVHUYHG
ꢎ[$ꢎꢎꢎꢄꢎꢎꢎꢎ
ꢎ[ꢁꢎꢎꢌꢄꢃꢎꢎꢎ
ꢎ[ꢁꢎꢎꢌꢄꢎꢎꢎꢎ
$3%
ꢁ
5HVHUYHG
ꢎ[ꢌ)))ꢄ))))
ꢎ[ꢌ)))ꢄ)&ꢎꢎ
5HVHUYHG
2SWLRQꢄ%\WHV
ꢎ[ꢌ)))ꢄ)ꢃꢎꢎ
ꢎ[ꢃꢎꢎꢎꢄꢎꢎꢎꢎ
5HVHUYHG
$3%
6\VWHPꢄPHPRU\
ꢎ[ꢁꢎꢎꢎꢄꢃꢎꢎꢎ
ꢎ[ꢁꢎꢎꢎꢄꢎꢎꢎꢎ
ꢀ
5HVHUYHG
5HVHUYHG
ꢎ[ꢌ)))ꢄ&ꢁꢎꢎ
ꢎ[ꢒꢎꢎꢎꢄꢎꢎꢎꢎ
5HVHUYHG
ꢆ
3HULSKHUDOV
5HVHUYHG
ꢎ[ꢁꢎꢎꢎꢄꢎꢎꢎꢎ
ꢎ[ꢎꢃꢎꢎꢄꢃꢎꢎꢎ
ꢌ
)ODVKꢄPHPRU\
5HVHUYHG
65$0
&2'(
ꢎ[ꢆꢎꢎꢎꢄꢎꢎꢎꢎ
ꢎ[ꢎꢃꢎꢎꢄꢎꢎꢎꢎ
ꢎ[ꢎꢎꢎꢎꢄꢃꢎꢎꢎ
ꢎ
)ODVKꢈꢄV\VWHPꢄ
PHPRU\ꢄRUꢄ65$0ꢈꢄ
GHSHQGLQJꢄRQꢄ%227ꢄ
FRQILJXUDWLRQ
ꢎ[ꢎꢎꢎꢎꢄꢎꢎꢎꢎ
ꢎ[ꢎꢎꢎꢎꢄꢎꢎꢎꢎ
06Yꢀꢁꢂꢆꢁ9ꢆ
34/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Memory mapping
Table 16. STM32F048x6 peripheral register boundary addresses
Bus
Boundary address
Size
Peripheral
0x4800 1800 - 0x5FFF FFFF
0x4800 1400 - 0x4800 17FF
0x4800 0C00 - 0x4800 13FF
0x4800 0800 - 0x4800 0BFF
0x4800 0400 - 0x4800 07FF
0x4800 0000 - 0x4800 03FF
0x4002 4400 - 0x47FF FFFF
0x4002 4000 - 0x4002 43FF
0x4002 3400 - 0x4002 3FFF
0x4002 3000 - 0x4002 33FF
0x4002 2400 - 0x4002 2FFF
0x4002 2000 - 0x4002 23FF
0x4002 1400 - 0x4002 1FFF
0x4002 1000 - 0x4002 13FF
0x4002 0400 - 0x4002 0FFF
0x4002 0000 - 0x4002 03FF
0x4001 8000 - 0x4001 FFFF
0x4001 5C00 - 0x4001 7FFF
0x4001 5800 - 0x4001 5BFF
0x4001 4C00 - 0x4001 57FF
0x4001 4800 - 0x4001 4BFF
0x4001 4400 - 0x4001 47FF
0x4001 3C00 - 0x4001 43FF
0x4001 3800 - 0x4001 3BFF
0x4001 3400 - 0x4001 37FF
0x4001 3000 - 0x4001 33FF
0x4001 2C00 - 0x4001 2FFF
0x4001 2800 - 0x4001 2BFF
0x4001 2400 - 0x4001 27FF
0x4001 0800 - 0x4001 23FF
0x4001 0400 - 0x4001 07FF
0x4001 0000 - 0x4001 03FF
0x4000 8000 - 0x4000 FFFF
~384 MB
1 KB
2 KB
1 KB
1 KB
1 KB
~128 MB
1 KB
3 KB
1 KB
3 KB
1 KB
3 KB
1 KB
3 KB
1 KB
32 KB
9 KB
1 KB
3 KB
1 KB
1 KB
2 KB
1 KB
1 KB
1 KB
1 KB
1 KB
1 KB
7 KB
1 KB
1 KB
32 KB
Reserved
GPIOF
Reserved
GPIOC
AHB2
GPIOB
GPIOA
Reserved
TSC
Reserved
CRC
Reserved
Flash memory interface
Reserved
RCC
AHB1
Reserved
DMA
Reserved
Reserved
DBGMCU
Reserved
TIM17
TIM16
Reserved
USART1
Reserved
SPI1/I2S1
TIM1
APB
Reserved
ADC
Reserved
EXTI
SYSCFG
Reserved
DocID026007 Rev 6
35/98
36
Memory mapping
STM32F048C6 STM32F048G6 STM32F048T6
Table 16. STM32F048x6 peripheral register boundary addresses (continued)
Bus
Boundary address
Size
Peripheral
0x4000 7C00 - 0x4000 7FFF
0x4000 7800 - 0x4000 7BFF
0x4000 7400 - 0x4000 77FF
0x4000 7000 - 0x4000 73FF
0x4000 6C00 - 0x4000 6FFF
0x4000 6400 - 0x4000 6BFF
0x4000 6000 - 0x4000 63FF
0x4000 5C00 - 0x4000 5FFF
0x4000 5800 - 0x4000 5BFF
0x4000 5400 - 0x4000 57FF
0x4000 4800 - 0x4000 53FF
0x4000 4400 - 0x4000 47FF
0x4000 3C00 - 0x4000 43FF
0x4000 3800 - 0x4000 3BFF
0x4000 3400 - 0x4000 37FF
0x4000 3000 - 0x4000 33FF
0x4000 2C00 - 0x4000 2FFF
0x4000 2800 - 0x4000 2BFF
0x4000 2400 - 0x4000 27FF
0x4000 2000 - 0x4000 23FF
0x4000 0800 - 0x4000 1FFF
0x4000 0400 - 0x4000 07FF
0x4000 0000 - 0x4000 03FF
1 KB
1 KB
1 KB
1 KB
1 KB
2 KB
1 KB
1 KB
1 KB
1 KB
3 KB
1 KB
2 KB
1 KB
1 KB
1 KB
1 KB
1 KB
1 KB
1 KB
6 KB
1 KB
1 KB
Reserved
CEC
Reserved
PWR
CRS
Reserved
USB RAM
USB
Reserved
I2C1
Reserved
USART2
Reserved
SPI2
APB
Reserved
IWDG
WWDG
RTC
Reserved
TIM14
Reserved
TIM3
TIM2
36/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
6
Electrical characteristics
6.1
Parameter conditions
Unless otherwise specified, all voltages are referenced to V
.
SS
6.1.1
Minimum and maximum values
Unless otherwise specified, the minimum and maximum values are guaranteed in the worst
conditions of ambient temperature, supply voltage and frequencies by tests in production on
100% of the devices with an ambient temperature at T = 25 °C and T = T max (given by
A
A
A
the selected temperature range).
Data based on characterization results, design simulation and/or technology characteristics
are indicated in the table footnotes and are not tested in production. Based on
characterization, the minimum and maximum values refer to sample tests and represent the
mean value plus or minus three times the standard deviation (mean ±3σ).
6.1.2
6.1.3
Typical values
Unless otherwise specified, typical data are based on T = 25 °C, V = 1.8 V and V
3.3 V. They are given only as design guidelines and are not tested.
=
A
DD
DDA
Typical ADC accuracy values are determined by characterization of a batch of samples from
a standard diffusion lot over the full temperature range, where 95% of the devices have an
error less than or equal to the value indicated (mean ±2σ).
Typical curves
Unless otherwise specified, all typical curves are given only as design guidelines and are
not tested.
6.1.4
6.1.5
Loading capacitor
The loading conditions used for pin parameter measurement are shown in Figure 7.
Pin input voltage
The input voltage measurement on a pin of the device is described in Figure 8.
Figure 7. Pin loading conditions
Figure 8. Pin input voltage
0&8ꢄSLQ
0&8ꢄSLQ
&ꢄ ꢄꢍꢎꢄS)
9,1
06ꢌꢂꢆꢌꢎ9ꢌ
06ꢌꢂꢆꢌꢌ9ꢌ
DocID026007 Rev 6
37/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
6.1.6
Power supply scheme
Figure 9. Power supply scheme
9%$7
%DFNXSꢄFLUFXLWU\
ꢉ/6(ꢈꢄ57&ꢈ
%DFNXSꢄUHJLVWHUVꢋ
ꢌꢇꢒꢍꢄ±ꢄꢀꢇꢒꢄ9
1325
3RZHUꢄVZLWFK
9''
9&25(
ꢆꢄ[ꢄ9''
9'',2ꢌ
287
.HUQHOꢄORJLF
,2
ORJLF
ꢆꢄ[ꢄꢌꢎꢎꢄQ)
ꢉ&38ꢈꢄ'LJLWDO
*3,2V
ꢆꢄ[ꢄ966
ꢔꢄ0HPRULHVꢋ
,1
ꢊꢄꢌꢄ[ꢄꢁꢇꢏꢄ)
9'',2ꢆ
9'',2ꢆ
9'',2ꢆ
287
ꢌꢎꢎꢄQ)
ꢊꢄꢁꢇꢏꢄ)ꢄ
,2
ORJLF
*3,2V
966
,1
9''$
9''$
$QDORJꢅ
ꢉ5&Vꢈꢄ3//ꢈꢄ«ꢋ
ꢌꢎꢄQ)
95()ꢊ
95()ꢓ
$'&
ꢊꢄꢌꢄ)
966$
06Yꢀꢁꢂꢂꢒ9ꢌ
Caution:
Each power supply pair (V /V , V
/V
etc.) must be decoupled with filtering ceramic
DD SS DDA SSA
capacitors as shown above. These capacitors must be placed as close as possible to, or
below, the appropriate pins on the underside of the PCB to ensure the good functionality of
the device.
38/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
6.1.7
Current consumption measurement
Figure 10. Current consumption measurement scheme
,
''B9%$7
9
%$7
,
,
''
9
''
9
'',2ꢆ
''$
9
''$
06ꢀꢌꢂꢂꢂ9ꢆ
DocID026007 Rev 6
39/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
6.2
Absolute maximum ratings
Stresses above the absolute maximum ratings listed in Table 17: Voltage characteristics,
Table 18: Current characteristics and Table 19: Thermal characteristics may cause
permanent damage to the device. These are stress ratings only and functional operation of
the device at these conditions is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
(1)
Table 17. Voltage characteristics
Symbol
Ratings
Min
Max
Unit
V
DD–VSS External main supply voltage
−0.3
- 0.3
1.95
V
V
VDDIO2–VSS External I/O supply voltage
VDDA–VSS External analog supply voltage
4.0
- 0.3
4.0
V
VDD–VDDA Allowed voltage difference for VDD > VDDA
-
0.4
V
VBAT–VSS External backup supply voltage
Input voltage on FT and FTf pins
Input voltage on POR pins
- 0.3
4.0
V
VSS −0.3
VSS −0.3
VSS −0.3
VSS −0.3
-
VDDIOx + 4.0(3)
V
4.0
4.0
4.0
50
V
(2)
VIN
Input voltage on TTa pins
V
Input voltage on any other pin
V
|∆VDDx
|VSSx - VSS
VESD(HBM)
|
Variations between different VDD power pins
mV
Variations between all the different ground
pins
|
-
50
mV
-
Electrostatic discharge voltage
(human body model)
see Section 6.3.11: Electrical
sensitivity characteristics
1. All main power (VDD, VDDA) and ground (VSS, VSSA) pins must always be connected to the external power
supply, in the permitted range.
2. VIN maximum must always be respected. Refer to Table 18: Current characteristics for the maximum
allowed injected current values.
3. Valid only if the internal pull-up/pull-down resistors are disabled. If internal pull-up or pull-down resistor is
enabled, the maximum limit is 4 V.
40/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
Table 18. Current characteristics
Symbol
Ratings
Max.
Unit
ΣIVDD
ΣIVSS
Total current into sum of all VDD power lines (source)(1)
Total current out of sum of all VSS ground lines (sink)(1)
Maximum current into each VDD power pin (source)(1)
Maximum current out of each VSS ground pin (sink)(1)
Output current sunk by any I/O and control pin
120
-120
100
-100
25
IVDD(PIN)
IVSS(PIN)
IIO(PIN)
Output current source by any I/O and control pin
Total output current sunk by sum of all I/Os and control pins(2)
Total output current sourced by sum of all I/Os and control pins(2)
Total output current sourced by sum of all I/Os supplied by VDDIO2
Injected current on POR, FT and FTf pins
-25
80
ΣIIO(PIN)
-80
mA
-40
-5/+0(4)
(3)
IINJ(PIN)
Injected current on TC and RST pin
± 5
Injected current on TTa pins(5)
± 5
ΣIINJ(PIN)
Total injected current (sum of all I/O and control pins)(6)
± 25
1. All main power (VDD, VDDA) and ground (VSS, VSSA) pins must always be connected to the external power supply, in the
permitted range.
2. This current consumption must be correctly distributed over all I/Os and control pins. The total output current must not be
sunk/sourced between two consecutive power supply pins referring to high pin count QFP packages.
3. A positive injection is induced by VIN > VDDIOx while a negative injection is induced by VIN < VSS. IINJ(PIN) must never be
exceeded. Refer to Table 17: Voltage characteristics for the maximum allowed input voltage values.
4. Positive injection is not possible on these I/Os and does not occur for input voltages lower than the specified maximum
value.
5. On these I/Os, a positive injection is induced by VIN > VDDA. Negative injection disturbs the analog performance of the
device. See note (2) below Table 54: ADC accuracy.
6. When several inputs are submitted to a current injection, the maximum ΣIINJ(PIN) is the absolute sum of the positive and
negative injected currents (instantaneous values).
Table 19. Thermal characteristics
Symbol
Ratings
Storage temperature range
Maximum junction temperature
Value
Unit
TSTG
TJ
–65 to +150
150
°C
°C
DocID026007 Rev 6
41/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
6.3
Operating conditions
6.3.1
General operating conditions
Table 20. General operating conditions
Symbol
Parameter
Conditions
Min
Max
Unit
fHCLK
fPCLK
VDD
Internal AHB clock frequency
Internal APB clock frequency
Standard operating voltage
-
-
-
0
0
48
48
MHz
1.65
1.95
V
V
Must not be supplied if VDD
is not present
VDDIO2
I/O supply voltage
1.65
VDD
2.4
3.6
3.6
3.6
Analog operating voltage
(ADC not used)
Must have a potential equal
to or higher than VDD
VDDA
V
Analog operating voltage
(ADC used)
VBAT
Backup operating voltage
-
1.65
–0.3
–0.3
–0.3
-
3.6
V
V
TC and RST I/O
VDDIOx+0.3
VIN
I/O input voltage
TTa and POR I/O
FT and FTf I/O
V
DDA+0.3(1)
5.2(1)
606
UFQFPN48
Power dissipation at TA = 85 °C
for suffix 6 or TA = 105 °C for
suffix 7(2)
PD
WLCSP36
-
313
mW
UFQFPN28
-
170
Maximum power dissipation
Low power dissipation(3)
Maximum power dissipation
Low power dissipation(3)
Suffix 6 version
–40
–40
–40
–40
–40
–40
85
Ambient temperature for the
suffix 6 version
°C
°C
°C
105
TA
TJ
105
Ambient temperature for the
suffix 7 version
125
105
Junction temperature range
Suffix 7 version
125
1. For operation with a voltage higher than VDDIOx + 0.3 V, the internal pull-up resistor must be disabled.
2. If TA is lower, higher PD values are allowed as long as TJ does not exceed TJmax. See Section 7.4: Thermal characteristics.
3. In low power dissipation state, TA can be extended to this range as long as TJ does not exceed TJmax (see Section 7.4:
Thermal characteristics).
6.3.2
Operating conditions at power-up / power-down
The parameters given in Table 21 are derived from tests performed under the ambient
temperature condition summarized in Table 20.
42/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
Table 21. Operating conditions at power-up / power-down
Symbol
Parameter
VDD rise time rate
VDD fall time rate
VDDA rise time rate
VDDA fall time rate
Conditions
Min
0
Max
∞
Unit
tVDD
-
20
0
∞
µs/V
∞
tVDDA
-
20
∞
6.3.3
Embedded reference voltage
The parameters given in Table 22 are derived from tests performed under the ambient
temperature and supply voltage conditions summarized in Table 20: General operating
conditions.
Table 22. Embedded internal reference voltage
Symbol
Parameter
Conditions
Min
Typ Max
Unit
Internal reference voltage –40 °C < TA < +105 °C
1.2
1.23 1.25
V
V
REFINT
ADC_IN17 buffer startup
time
tSTART
-
-
-
-
10(1)
µs
µs
ADC sampling time when
reading the internal
reference voltage
4(1)
tS_vrefint
-
-
Internal reference voltage
spread over the
10(1)
∆VREFINT
VDDA = 3 V
-
-
mV
temperature range
- 100(1)
1.5
100(1)
4.5
TCoeff
Temperature coefficient
-
-
-
ppm/°C
ms
TVREFINT_RDY Internal reference voltage
2.5
(2)
temporization
1. Guaranteed by design, not tested in production.
2. Guaranteed by design, not tested in production. This parameter is the latency between the time when pin
NPOR is set to 1 by the application and the time when the VREFINTRDYF status bit is set to 1 by the
hardware.
6.3.4
Supply current characteristics
The current consumption is a function of several parameters and factors such as the
operating voltage, ambient temperature, I/O pin loading, device software configuration,
operating frequencies, I/O pin switching rate, program location in memory and executed
binary code.
The current consumption is measured as described in Figure 10: Current consumption
measurement scheme.
All Run-mode current consumption measurements given in this section are performed with a
reduced code that gives a consumption equivalent to CoreMark code.
DocID026007 Rev 6
43/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
Typical and maximum current consumption
The MCU is placed under the following conditions:
•
•
•
All I/O pins are in analog input mode
All peripherals are disabled except when explicitly mentioned
The Flash memory access time is adjusted to the f
frequency:
HCLK
–
–
0 wait state and Prefetch OFF from 0 to 24 MHz
1 wait state and Prefetch ON above 24 MHz
= f
•
When the peripherals are enabled f
PCLK
HCLK
The parameters given in Table 23 to Table 27 are derived from tests performed under
ambient temperature and supply voltage conditions summarized in Table 20: General
operating conditions.
44/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
Table 23. Typical and maximum current consumption from V supply at V = 1.8 V
DD
DD
All peripherals enabled(1)
All peripherals disabled
(2)
(2)
Max @ TA
Max @ TA
Conditions
fHCLK
Unit
Typ
Typ
25 °C
85 °C 105 °C
25 °C 85 °C 105 °C
HSI48
48 MHz 19.0
48 MHz 18.5
32 MHz 12.5
20.4
20.0
13.2
10.4
4.0
20.9
20.5
13.6
10.7
4.1
21.3
20.9
14.0
11.0
4.2
11.7
11.5
7.8
6.2
2.3
0.5
11.6
8.0
6.3
2.3
10.9
10.7
7.2
5.6
1.6
0.2
10.8
7.4
5.7
1.7
2.7
2.6
1.7
1.4
0.5
0.1
2.6
1.9
1.4
0.5
12.2
12.1
8.4
6.6
2.5
0.7
12.1
8.6
6.8
2.5
11.4
11.4
7.6
5.9
2.0
0.3
11.4
7.8
5.9
2.1
2.8
2.7
1.9
1.4
0.5
0.2
2.7
2.0
1.4
0.6
12.8
12.6
8.7
6.9
2.6
0.7
12.7
8.8
7.0
2.6
12.0
11.9
8.0
6.3
2.0
0.3
12.0
8.2
6.3
2.1
2.9
2.8
2.0
1.6
0.6
0.2
2.8
2.1
1.6
0.6
12.9
12.8
8.9
7.1
2.6
0.8
12.8
9.1
7.1
2.7
12.2
12.1
8.3
6.5
2.0
0.4
12.1
8.4
6.5
2.2
3.1
3.0
2.3
1.6
0.6
0.2
3.0
2.3
1.7
0.8
External
clock (HSE 24 MHz 10.1
bypass)
8 MHz
1 MHz
3.5
0.7
mA
0.8
0.9
1.0
48 MHz 18.7
32 MHz 12.7
24 MHz 10.2
20.2
13.4
10.6
4.2
20.6
13.8
11.0
4.3
21.0
14.2
11.1
4.5
Internal
clock (HSI)
8 MHz
3.7
HSI48
48 MHz 18.2
48 MHz 17.8
32 MHz 12.1
19.6
19.2
12.6
9.9
20.0
19.7
13.0
10.1
3.6
20.4
20.0
13.4
10.4
3.7
External
clock (HSE 24 MHz 9.6
bypass)
8 MHz
1 MHz
3.0
0.4
3.4
IDD
0.5
0.6
0.7
48 MHz 18.0
32 MHz 12.3
24 MHz 9.8
19.4
12.9
10.1
3.6
19.9
13.2
10.4
3.7
20.2
13.6
10.6
3.9
Internal
clock (HSI)
8 MHz
3.2
mA
HSI48
48 MHz 10.9
48 MHz 10.7
32 MHz 7.8
12.2
12.1
8.3
13.0
12.8
8.6
13.3
13.1
9.0
External
clock (HSE 24 MHz 6.2
bypass)
6.8
7.2
7.4
8 MHz
1 MHz
2.0
0.3
2.5
2.6
2.7
0.3
0.4
0.5
48 MHz 10.8
32 MHz 7.9
24 MHz 6.3
12.1
8.4
12.9
8.7
13.2
9.2
Internal
clock (HSI)
6.9
7.3
7.5
8 MHz
2.0
2.6
2.7
2.8
1. USB is kept disabled as this IP functions only with a 48 MHz clock.
2. Data based on characterization results, not tested in production unless otherwise specified.
DocID026007 Rev 6
45/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
Table 24. Typical and maximum current consumption from the V
supply
= 3.6 V
DDA
DDA
V
= 2.4 V
V
DDA
Para-
meter
Conditions
(2)
(2)
Symbol
fHCLK
Unit
Max @ TA
25 °C 85 °C 105 °C
Max @ TA
25 °C 85 °C 105 °C
(1)
Typ
Typ
HSI48
48 MHz 308
48 MHz 147
32 MHz 101
24 MHz 79
325
166
118
94
330
176
123
98
340
180
125
100
3
316
160
109
86
332
179
126
100
3
338
191
132
104
3
347
195
135
106
4
HSE
bypass,
PLL on
Supply
current in
Run or
Sleep
HSE
bypass,
PLL off
8 MHz
1 MHz
1
1
3
3
2
mode,
IDDA
code
µA
2
2
2
2
2
3
3
executing
from
Flash
memory
or RAM
48 MHz 219
32 MHz 172
24 MHz 150
239
191
167
250
198
172
254
201
174
240
190
165
260
207
181
272
215
187
276
218
189
HSI clock,
PLL on
HSI clock,
PLL off
8 MHz
71
79
81
82
81
89
91
92
1. Current consumption from the VDDA supply is independent of whether the digital peripherals are enabled or disabled, being
in Run or Sleep mode or executing from Flash memory or RAM. Furthermore, when the PLL is off, IDDA is independent from
the frequency.
2. Data based on characterization results, not tested in production unless otherwise specified.
Table 25. Typical and maximum consumption in Stop mode
Typ. @ VDD = 1.8 V
Max
Symbol Parameter
Conditions
Unit
IDD
Supply
current in
Stop mode
0.4
2.3
1.5
14.9
2.6
35.6
3.4
All oscillators OFF
µA
IDDA
1.0 1.0 1.0 1.0 1.1 1.1 1.2
46/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
Table 26. Typical and maximum current consumption from the V
Typ @ VBAT
supply
Max(1)
BAT
Symbol Parameter
Conditions
Unit
TA =
TA =
TA =
25 °C 85 °C 105 °C
LSE & RTC ON; “Xtal
mode”: lower driving
capability;
0.5 0.5 0.6 0.7 0.9 1.1
1.2
1.6
1.5
2.0
2.0
2.6
RTC
LSEDRV[1:0] = '00'
domain
supply
current
IDD VBAT
_
µA
LSE & RTC ON; “Xtal
mode” higher driving
capability;
0.8 0.9 1.1 1.2 1.4 1.5
LSEDRV[1:0] = '11'
1. Data based on characterization results, not tested in production.
Typical current consumption
The MCU is placed under the following conditions:
•
•
•
V
= V
= 1.8 V
DDA
DD
All I/O pins are in analog input configuration
The Flash memory access time is adjusted to f
frequency:
HCLK
–
–
0 wait state and Prefetch OFF from 0 to 24 MHz
1 wait state and Prefetch ON above 24 MHz
= f
•
•
•
When the peripherals are enabled, f
PCLK
HCLK
PLL is used for frequencies greater than 8 MHz
AHB prescaler of 2, 4, 8 and 16 is used for the frequencies 4 MHz, 2 MHz, 1 MHz and
500 kHz respectively
DocID026007 Rev 6
47/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
Table 27. Typical current consumption, code executing from Flash memory,
running from HSE 8 MHz crystal
Typical consumption in
Run mode
Typical consumption in
Sleep mode
Symbol Parameter
fHCLK
Unit
Peripherals Peripherals Peripherals Peripherals
enabled
disabled
enabled
disabled
48 MHz
36 MHz
32 MHz
24 MHz
16 MHz
8 MHz
19.8
15.0
13.5
10.2
7.1
12.0
9.3
8.4
6.5
4.6
2.6
1.5
1.0
0.8
0.6
11.5
8.7
7.8
6.0
4.2
2.3
1.3
0.9
0.6
0.5
3.1
2.6
2.4
1.8
1.4
0.8
0.5
0.5
0.4
0.4
Current
consumption
from VDD
supply
IDD
mA
3.9
4 MHz
2.3
2 MHz
1.4
1 MHz
1.0
500 kHz
48 MHz
36 MHz
32 MHz
24 MHz
16 MHz
8 MHz
0.8
146
115
105
83
61
1
Current
consumption
from VDDA
supply
IDDA
μA
4 MHz
1
2 MHz
1
1 MHz
1
500 kHz
1
I/O system current consumption
The current consumption of the I/O system has two components: static and dynamic.
I/O static current consumption
All the I/Os used as inputs with pull-up generate current consumption when the pin is
externally held low. The value of this current consumption can be simply computed by using
the pull-up/pull-down resistors values given in Table 47: I/O static characteristics.
For the output pins, any external pull-down or external load must also be considered to
estimate the current consumption.
Additional I/O current consumption is due to I/Os configured as inputs if an intermediate
voltage level is externally applied. This current consumption is caused by the input Schmitt
48/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
trigger circuits used to discriminate the input value. Unless this specific configuration is
required by the application, this supply current consumption can be avoided by configuring
these I/Os in analog mode. This is notably the case of ADC input pins which should be
configured as analog inputs.
Caution:
Any floating input pin can also settle to an intermediate voltage level or switch inadvertently,
as a result of external electromagnetic noise. To avoid current consumption related to
floating pins, they must either be configured in analog mode, or forced internally to a definite
digital value. This can be done either by using pull-up/down resistors or by configuring the
pins in output mode.
I/O dynamic current consumption
In addition to the internal peripheral current consumption measured previously (see
Table 29: Peripheral current consumption), the I/Os used by an application also contribute
to the current consumption. When an I/O pin switches, it uses the current from the I/O
supply voltage to supply the I/O pin circuitry and to charge/discharge the capacitive load
(internal or external) connected to the pin:
ISW = VDDIOx × fSW × C
where
I
is the current sunk by a switching I/O to charge/discharge the capacitive load
SW
V
is the I/O supply voltage
DDIOx
f
is the I/O switching frequency
SW
C is the total capacitance seen by the I/O pin: C = C
+ C
+ C
EXT S
INT
C is the PCB board capacitance including the pad pin.
S
The test pin is configured in push-pull output mode and is toggled by software at a fixed
frequency.
DocID026007 Rev 6
49/98
83
Electrical characteristics
Symbol
STM32F048C6 STM32F048G6 STM32F048T6
Table 28. Switching output I/O current consumption
I/O toggling
frequency (fSW
Parameter
Conditions(1)
Typ
Unit
)
2 MHz
4 MHz
8 MHz
18 MHz
36 MHz
48 MHz
2 MHz
4 MHz
8 MHz
18 MHz
36 MHz
48 MHz
2 MHz
4 MHz
8 MHz
18 MHz
36 MHz
2 MHz
4 MHz
8 MHz
18 MHz
36 MHz
2 MHz
4 MHz
8 MHz
18 MHz
0.09
0.17
0.34
0.79
1.50
2.06
0.13
0.26
0.50
1.18
2.27
3.03
0.18
0.36
0.69
1.60
3.27
0.23
0.45
0.87
2.0
VDDIOx = 1.8 V
CEXT = 0 pF
C = CINT + CEXT + CS
VDDIOx = 1.8 V
CEXT = 10 pF
C = CINT + CEXT + CS
I/O current
consumption
ISW
mA
VDDIOx = 1.8 V
CEXT = 22 pF
C = CINT + CEXT + CS
VDDIOx = 1.8 V
CEXT = 33 pF
C = CINT + CEXT + CS
3.7
0.29
0.55
1.09
2.43
VDDIOx = 1.8 V
CEXT = 47 pF
C = CINT + CEXT + CS
1. CS = 5 pF (estimated value).
50/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
On-chip peripheral current consumption
The current consumption of the on-chip peripherals is given in Table 29. The MCU is placed
under the following conditions:
•
•
•
All I/O pins are in analog mode
All peripherals are disabled unless otherwise mentioned
The given value is calculated by measuring the current consumption
–
–
with all peripherals clocked off
with only one peripheral clocked on
•
Ambient operating temperature and supply voltage conditions summarized in Table 17:
Voltage characteristics
Table 29. Peripheral current consumption
Peripheral
BusMatrix(1)
Typical consumption at 25 °C
Unit
2.2
1.9
5.1
15.0
8.2
7.7
2.1
1.8
1.1
4.9
49.8
CRC
DMA
Flash memory interface
GPIOA
AHB
GPIOB
µA/MHz
GPIOC
GPIOF
SRAM
TSC
All AHB peripherals
DocID026007 Rev 6
51/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
Table 29. Peripheral current consumption (continued)
Peripheral
Typical consumption at 25 °C
Unit
APB-Bridge(2)
2.9
3.9
ADC(3)
CEC
1.5
CRS
1.0
DBG (MCU Debug Support)
0.2
I2C1
3.6
PWR
1.4
SPI1
8.5
SPI2
6.1
SYSCFG
TIM1
1.8
15.1
16.8
11.7
5.5
APB
µA/MHz
TIM2
TIM3
TIM14
TIM16
7.0
TIM17
6.9
USART1
USART2
USB
17.8
5.6
4.9
WWDG
All APB peripherals
1.4
123.8
1. The BusMatrix is automatically active when at least one master is ON (CPU, DMA).
2. The APB Bridge is automatically active when at least one peripheral is ON on the Bus.
3. The power consumption of the analog part (IDDA) of peripherals such as ADC is not included. Refer to the
tables of characteristics in the subsequent sections.
52/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
6.3.5
Wakeup time from low-power mode
The wakeup times given in Table 30 are the latency between the event and the execution of
the first user instruction. The device goes in low-power mode after the WFE (Wait For
Event) instruction, in the case of a WFI (Wait For Interruption) instruction, 16 CPU cycles
must be added to the following timings due to the interrupt latency in the Cortex M0
architecture.
The SYSCLK clock source setting is kept unchanged after wakeup from Sleep mode.
During wakeup from Stop mode, SYSCLK takes the default setting: HSI 8 MHz.
The wakeup source from Sleep and Stop mode is an EXTI line configured in event mode.
All timings are derived from tests performed under the ambient temperature and supply
voltage conditions summarized in Table 20: General operating conditions.
Table 30. Low-power mode wakeup timings
Typ @ VDDA
Symbol
Parameter
Max
Unit
= 1.8 V = 3.3 V
3.5 2.8
4 SYSCLK cycles
tWUSTOP
Wakeup from Stop mode
Wakeup from Sleep mode
5.3
-
µs
µs
tWUSLEEP
6.3.6
External clock source characteristics
High-speed external user clock generated from an external source
In bypass mode the HSE oscillator is switched off and the input pin is a standard GPIO.
The external clock signal has to respect the I/O characteristics in Section 6.3.13. However,
the recommended clock input waveform is shown in Figure 11: High-speed external clock
source AC timing diagram.
Table 31. High-speed external user clock characteristics
Symbol
Parameter(1)
Min
Typ
Max
Unit
fHSE_ext User external clock source frequency
VHSEH OSC_IN input pin high level voltage
-
8
-
32
MHz
0.7 VDDIOx
VSS
VDDIOx
V
VHSEL
OSC_IN input pin low level voltage
OSC_IN high or low time
-
0.3 VDDIOx
tw(HSEH)
tw(HSEL)
15
-
-
-
-
ns
tr(HSE)
tf(HSE)
OSC_IN rise or fall time
20
1. Guaranteed by design, not tested in production.
DocID026007 Rev 6
53/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
Figure 11. High-speed external clock source AC timing diagram
W
Zꢉ+6(+ꢋ
9
+6(+
ꢂꢎꢑ
ꢌꢎꢑ
9
+6(/
W
W
W
W
Uꢉ+6(ꢋ
Iꢉ+6(ꢋ
Zꢉ+6(/ꢋ
7
+6(
06ꢌꢂꢆꢌꢁ9ꢆ
Low-speed external user clock generated from an external source
In bypass mode the LSE oscillator is switched off and the input pin is a standard GPIO.
The external clock signal has to respect the I/O characteristics in Section 6.3.13. However,
the recommended clock input waveform is shown in Figure 12.
Table 32. Low-speed external user clock characteristics
Symbol
Parameter(1)
Min
Typ
Max
Unit
fLSE_ext User external clock source frequency
VLSEH OSC32_IN input pin high level voltage
VLSEL OSC32_IN input pin low level voltage
-
32.768
1000
VDDIOx
kHz
0.7 VDDIOx
VSS
-
-
V
0.3 VDDIOx
tw(LSEH)
OSC32_IN high or low time
tw(LSEL)
450
-
-
-
-
ns
tr(LSE)
OSC32_IN rise or fall time
tf(LSE)
50
1. Guaranteed by design, not tested in production.
Figure 12. Low-speed external clock source AC timing diagram
W
Zꢉ/6(+ꢋ
9
/6(+
ꢂꢎꢑ
ꢌꢎꢑ
9
/6(/
W
W
W
Uꢉ/6(ꢋ
Iꢉ/6(ꢋ
W
Zꢉ/6(/ꢋ
7
/6(
06ꢌꢂꢆꢌꢍ9ꢆ
54/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
High-speed external clock generated from a crystal/ceramic resonator
The high-speed external (HSE) clock can be supplied with a 4 to 32 MHz crystal/ceramic
resonator oscillator. All the information given in this paragraph are based on design
simulation results obtained with typical external components specified in Table 33. In the
application, the resonator and the load capacitors have to be placed as close as possible to
the oscillator pins in order to minimize output distortion and startup stabilization time. Refer
to the crystal resonator manufacturer for more details on the resonator characteristics
(frequency, package, accuracy).
Table 33. HSE oscillator characteristics
Symbol
Parameter
Conditions(1)
Min(2) Typ Max(2) Unit
fOSC_IN Oscillator frequency
-
4
-
8
200
-
32
-
MHz
RF
Feedback resistor
-
kΩ
During startup(3)
-
8.5
VDD = 1.8 V,
Rm = 30 Ω,
CL = 10 pF@8 MHz
-
-
-
-
-
0.4
0.5
0.8
1
-
-
-
-
-
VDD = 1.8 V,
Rm = 45 Ω,
CL = 10 pF@8 MHz
VDD = 1.8 V,
IDD
HSE current consumption
mA
Rm = 30 Ω,
CL = 5 pF@32 MHz
VDD = 1.8 V,
Rm = 30 Ω,
CL = 10 pF@32 MHz
VDD = 1.8 V,
Rm = 30 Ω,
1.5
CL = 20 pF@32 MHz
gm
Oscillator transconductance
Startup time
Startup
10
-
-
-
-
mA/V
ms
(4)
tSU(HSE)
VDD is stabilized
2
1. Resonator characteristics given by the crystal/ceramic resonator manufacturer.
2. Guaranteed by design, not tested in production.
3. This consumption level occurs during the first 2/3 of the tSU(HSE) startup time
4. tSU(HSE) is the startup time measured from the moment it is enabled (by software) to a stabilized 8 MHz
oscillation is reached. This value is measured for a standard crystal resonator and it can vary significantly
with the crystal manufacturer
For C and C , it is recommended to use high-quality external ceramic capacitors in the
L1
L2
5 pF to 20 pF range (Typ.), designed for high-frequency applications, and selected to match
the requirements of the crystal or resonator (see Figure 13). C and C are usually the
L1
L2
same size. The crystal manufacturer typically specifies a load capacitance which is the
series combination of C and C . PCB and MCU pin capacitance must be included (10 pF
L1
L2
can be used as a rough estimate of the combined pin and board capacitance) when sizing
and C .
C
L1
L2
Note:
For information on selecting the crystal, refer to the application note AN2867 “Oscillator
design guide for ST microcontrollers” available from the ST website www.st.com.
DocID026007 Rev 6
55/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
Figure 13. Typical application with an 8 MHz crystal
5HVRQDWRUꢄZLWKꢄLQWHJUDWHGꢄ
FDSDFLWRUV
&
/ꢌ
26&B,1
I+6(
%LDVꢄ
FRQWUROOHGꢄ
JDLQ
ꢃꢄ0+]ꢄ
UHVRQDWRU
5)
ꢉꢌꢋ
26&B287
5(;7
&
/ꢆ
06ꢌꢂꢃꢏꢒ9ꢌ
1. REXT value depends on the crystal characteristics.
Low-speed external clock generated from a crystal resonator
The low-speed external (LSE) clock can be supplied with a 32.768 kHz crystal resonator
oscillator. All the information given in this paragraph are based on design simulation results
obtained with typical external components specified in Table 34. In the application, the
resonator and the load capacitors have to be placed as close as possible to the oscillator
pins in order to minimize output distortion and startup stabilization time. Refer to the crystal
resonator manufacturer for more details on the resonator characteristics (frequency,
package, accuracy).
Table 34. LSE oscillator characteristics (fLSE = 32.768 kHz)
Symbol
Parameter
Conditions(1)
Min(2) Typ Max(2) Unit
low drive capability
medium-low drive capability
medium-high drive capability
high drive capability
-
-
0.5
0.9
-
-
1
IDD
LSE current consumption
µA
-
1.3
-
-
1.6
low drive capability
5
8
15
25
-
-
-
-
-
-
-
medium-low drive capability
medium-high drive capability
high drive capability
-
Oscillator
transconductance
gm
µA/V
s
-
-
(3)
tSU(LSE)
Startup time
VDDIOx is stabilized
2
1. Refer to the note and caution paragraphs below the table, and to the application note AN2867 “Oscillator design guide for
ST microcontrollers”.
2. Guaranteed by design, not tested in production.
3. tSU(LSE) is the startup time measured from the moment it is enabled (by software) to a stabilized 32.768 kHz oscillation is
reached. This value is measured for a standard crystal and it can vary significantly with the crystal manufacturer
56/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
Note:
For information on selecting the crystal, refer to the application note AN2867 “Oscillator
design guide for ST microcontrollers” available from the ST website www.st.com.
Figure 14. Typical application with a 32.768 kHz crystal
5HVRQDWRUꢄZLWKꢄLQWHJUDWHGꢄ
FDSDFLWRUV
&
/ꢌ
26&ꢀꢆB,1
I/6(
'ULYHꢄ
ꢀꢆꢇꢏꢒꢃꢄN+]ꢄ
UHVRQDWRU
SURJUDPPDEOHꢄ
DPSOLILHU
26&ꢀꢆB287
&
/ꢆ
06ꢀꢎꢆꢍꢀ9ꢆ
Note:
An external resistor is not required between OSC32_IN and OSC32_OUT and it is forbidden
to add one.
6.3.7
Internal clock source characteristics
The parameters given in Table 35 are derived from tests performed under ambient
temperature and supply voltage conditions summarized in Table 20: General operating
conditions. The provided curves are characterization results, not tested in production.
DocID026007 Rev 6
57/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
High-speed internal (HSI) RC oscillator
(1)
Table 35. HSI oscillator characteristics
Parameter Conditions Min
Frequency
HSI user trimming step
Symbol
Typ
Max
Unit
fHSI
-
-
8
-
-
-
-
-
-
-
-
-
-
MHz
%
TRIM
-
-
-
1(2)
55(2)
3.8(3)
2.3(3)
2(3)
2(3)
2(3)
1
DuCy(HSI) Duty cycle
45(2)
-2.8(3)
-1.9(3)
-1.9(3)
-1.3(3)
-1(3)
%
TA = -40 to 105°C
TA = -10 to 85°C
TA = 0 to 85°C
TA = 0 to 70°C
TA = 0 to 55°C
TA = 25°C(4)
-
Accuracy of the HSI
oscillator
ACCHSI
%
-1
tsu(HSI)
HSI oscillator startup time
1(2)
2(2)
µs
HSI oscillator power
consumption
IDDA(HSI)
-
-
80
100(2)
µA
1. VDDA = 3.3 V, TA = -40 to 105°C unless otherwise specified.
2. Guaranteed by design, not tested in production.
3. Data based on characterization results, not tested in production.
4. Factory calibrated, parts not soldered.
Figure 15. HSI oscillator accuracy characterization results for soldered parts
ꢂꢈ
."9
.*/
ꢉꢈ
ꢄꢈ
ꢇꢈ
ꢃꢈ
5ꢀꢀ<$>
"ꢀꢀ
ꢁꢂꢃ
ꢁꢄꢃ
ꢃ
ꢄꢃ
ꢂꢃ
ꢅꢃ
ꢆꢃ
ꢇꢃꢃ
ꢇꢄꢃ
ꢁꢇꢈ
ꢁꢄꢈ
ꢁꢉꢈ
ꢁꢂꢈ
06ꢀꢎꢂꢃꢍ9ꢁ
58/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
High-speed internal 14 MHz (HSI14) RC oscillator (dedicated to ADC)
(1)
Table 36. HSI14 oscillator characteristics
Symbol
Parameter
Frequency
HSI14 user-trimming step
Conditions
Min
Typ
Max
Unit
fHSI14
TRIM
-
-
-
-
-
14
-
-
MHz
%
1(2)
DuCy(HSI14) Duty cycle
45(2)
-
55(2)
5.1(3)
3.1(3)
2.3(3)
1
%
TA = –40 to 105 °C –4.2(3)
TA = –10 to 85 °C –3.2(3)
-
%
-
%
Accuracy of the HSI14
oscillator (factory calibrated)
ACCHSI14
TA = 0 to 70 °C
–2.5(3)
-
%
TA = 25 °C
-
–1
-
%
tsu(HSI14) HSI14 oscillator startup time
1(2)
-
2(2)
µs
HSI14 oscillator power
IDDA(HSI14)
-
-
100 150(2)
µA
consumption
1.
2. Guaranteed by design, not tested in production.
3. Data based on characterization results, not tested in production.
VDDA = 3.3 V, TA = –40 to 105 °C unless otherwise specified.
Figure 16. HSI14 oscillator accuracy characterization results
ꢍꢑ
0$;
0,1
ꢁꢑ
ꢀꢑ
ꢆꢑ
ꢌꢑ
ꢎꢑ
7ꢄꢄ>&@
$
ꢓꢁꢎ
ꢓꢆꢎ
ꢎ
ꢆꢎ
ꢁꢎ
ꢒꢎ
ꢃꢎ
ꢌꢎꢎ
ꢌꢆꢎ
ꢌꢑ
ꢆꢑ
ꢀꢑ
ꢓ
ꢓ
ꢓ
ꢓꢁꢑ
ꢓꢍꢑ
06ꢀꢎꢂꢃꢒ9ꢆ
DocID026007 Rev 6
59/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
High-speed internal 48 MHz (HSI48) RC oscillator
(1)
Table 37. HSI48 oscillator characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
fHSI48
TRIM
Frequency
-
-
-
-
48
-
MHz
%
HSI48 user-trimming step
0.09(2)
45(2)
0.14
0.2(2)
55(2)
4.7(3)
3.7(3)
3.4(3)
2.9
DuCy(HSI48) Duty cycle
-
-
-
-
-
-
%
TA = –40 to 105 °C -4.9(3)
%
TA = –10 to 85 °C
TA = 0 to 70 °C
TA = 25 °C
-
-4.1(3)
-3.8(3)
-2.8
-
%
Accuracy of the HSI48
oscillator (factory calibrated)
ACCHSI48
%
%
tsu(HSI48) HSI48 oscillator startup time
6(2)
µs
HSI48 oscillator power
IDDA(HSI48)
-
-
312
350(2)
µA
consumption
1.
VDDA = 3.3 V, TA = –40 to 105 °C unless otherwise specified.
2. Guaranteed by design, not tested in production.
3. Data based on characterization results, not tested in production.
Figure 17. HSI48 oscillator accuracy characterization results
ꢍꢑ
0$;
0,1
ꢁꢑ
ꢀꢑ
ꢆꢑ
ꢌꢑ
ꢎꢑ
7ꢄꢄ>&@
$
ꢓꢁꢎ
ꢓꢆꢎ
ꢎ
ꢆꢎ
ꢁꢎ
ꢒꢎ
ꢃꢎ
ꢌꢎꢎ
ꢌꢆꢎ
ꢌꢑ
ꢆꢑ
ꢀꢑ
ꢓ
ꢓ
ꢓ
ꢓꢁꢑ
ꢓꢍꢑ
06ꢀꢁꢆꢎꢒ9ꢌ
60/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Low-speed internal (LSI) RC oscillator
Electrical characteristics
(1)
Table 38. LSI oscillator characteristics
Symbol
Parameter
Min
Typ
Max
Unit
fLSI
Frequency
30
-
40
-
50
85
kHz
µs
(2)
tsu(LSI)
LSI oscillator startup time
(2)
IDDA(LSI)
LSI oscillator power consumption
-
0.75
1.2
µA
1.
VDDA = 3.3 V, TA = –40 to 105 °C unless otherwise specified.
2. Guaranteed by design, not tested in production.
6.3.8
PLL characteristics
The parameters given in Table 39 are derived from tests performed under ambient
temperature and supply voltage conditions summarized in Table 20: General operating
conditions.
Table 39. PLL characteristics
Value
Symbol
Parameter
Unit
Min
Typ
Max
PLL input clock(1)
1(2)
40(2)
16(2)
-
8.0
24(2)
60(2)
48
MHz
%
fPLL_IN
PLL input clock duty cycle
PLL multiplier output clock
PLL lock time
-
-
-
-
fPLL_OUT
tLOCK
MHz
µs
200(2)
300(2)
JitterPLL
Cycle-to-cycle jitter
-
ps
1. Take care to use the appropriate multiplier factors to obtain PLL input clock values compatible with the
range defined by fPLL_OUT
.
2. Guaranteed by design, not tested in production.
6.3.9
Memory characteristics
Flash memory
The characteristics are given at T = –40 to 105 °C unless otherwise specified.
A
Table 40. Flash memory characteristics
Symbol
Parameter
Conditions
Min
Typ
Max(1) Unit
tprog
16-bit programming time TA = - 40 to +105 °C
40
20
20
-
53.5
60
40
40
10
12
µs
ms
ms
mA
mA
tERASE Page (1 KB) erase time TA = - 40 to +105 °C
-
-
-
-
tME
Mass erase time
TA = - 40 to +105 °C
Write mode
IDD
Supply current
Erase mode
-
1. Guaranteed by design, not tested in production.
DocID026007 Rev 6
61/98
83
Electrical characteristics
Symbol
STM32F048C6 STM32F048G6 STM32F048T6
Table 41. Flash memory endurance and data retention
Parameter
Conditions
Min(1)
Unit
NEND
Endurance
TA = –40 to +105 °C
kcycle
10
30
10
20
1 kcycle(2) at TA = 85 °C
1 kcycle(2) at TA = 105 °C
10 kcycle(2) at TA = 55 °C
tRET
Data retention
Year
1. Data based on characterization results, not tested in production.
2. Cycling performed over the whole temperature range.
6.3.10
EMC characteristics
Susceptibility tests are performed on a sample basis during device characterization.
Functional EMS (electromagnetic susceptibility)
While a simple application is executed on the device (toggling 2 LEDs through I/O ports).
the device is stressed by two electromagnetic events until a failure occurs. The failure is
indicated by the LEDs:
•
Electrostatic discharge (ESD) (positive and negative) is applied to all device pins until
a functional disturbance occurs. This test is compliant with the IEC 61000-4-2 standard.
•
FTB: A Burst of Fast Transient voltage (positive and negative) is applied to V and
DD
V
through a 100 pF capacitor, until a functional disturbance occurs. This test is
SS
compliant with the IEC 61000-4-4 standard.
A device reset allows normal operations to be resumed.
The test results are given in Table 42. They are based on the EMS levels and classes
defined in application note AN1709.
Table 42. EMS characteristics
Level/
Class
Symbol
Parameter
Conditions
VDD = 1.8 V, LQFP48, TA = +25 °C,
fHCLK = 48 MHz,
conforming to IEC 61000-4-2
Voltage limits to be applied on any I/O pin
to induce a functional disturbance
VFESD
3B
4B
Fast transient voltage burst limits to be
VDD = 1.8 V, LQFP48, TA = +25°C,
VEFTB applied through 100 pF on VDD and VSS fHCLK = 48 MHz,
pins to induce a functional disturbance
conforming to IEC 61000-4-4
Designing hardened software to avoid noise problems
EMC characterization and optimization are performed at component level with a typical
application environment and simplified MCU software. It should be noted that good EMC
performance is highly dependent on the user application and the software in particular.
Therefore it is recommended that the user applies EMC software optimization and
prequalification tests in relation with the EMC level requested for his application.
62/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Software recommendations
Electrical characteristics
The software flowchart must include the management of runaway conditions such as:
•
•
•
Corrupted program counter
Unexpected reset
Critical Data corruption (for example control registers)
Prequalification trials
Most of the common failures (unexpected reset and program counter corruption) can be
reproduced by manually forcing a low state on the NRST pin or the Oscillator pins for 1
second.
To complete these trials, ESD stress can be applied directly on the device, over the range of
specification values. When unexpected behavior is detected, the software can be hardened
to prevent unrecoverable errors occurring (see application note AN1015).
Electromagnetic Interference (EMI)
The electromagnetic field emitted by the device are monitored while a simple application is
executed (toggling 2 LEDs through the I/O ports). This emission test is compliant with
IEC 61967-2 standard which specifies the test board and the pin loading.
Table 43. EMI characteristics
Max vs. [fHSE/fHCLK
8/48 MHz
]
Monitored
frequency band
Symbol Parameter
Conditions
Unit
0.1 to 30 MHz
30 to 130 MHz
130 MHz to 1 GHz
EMI Level
-9
12
17
3
VDD = 1.8 V, TA = 25 °C,
LQFP48 package
compliant with
dBµV
-
SEMI
Peak level
IEC 61967-2
6.3.11
Electrical sensitivity characteristics
Based on three different tests (ESD, LU) using specific measurement methods, the device is
stressed in order to determine its performance in terms of electrical sensitivity.
Electrostatic discharge (ESD)
Electrostatic discharges (a positive then a negative pulse separated by 1 second) are
applied to the pins of each sample according to each pin combination. The sample size
depends on the number of supply pins in the device (3 parts × (n+1) supply pins). This test
conforms to the JESD22-A114/C101 standard.
DocID026007 Rev 6
63/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
Table 44. ESD absolute maximum ratings
Maximum
value(1)
Symbol
Ratings
Conditions
Packages Class
Unit
Electrostatic discharge voltage TA = +25 °C, conforming
VESD(HBM)
All
All
2
2000
500
V
V
(human body model)
to JESD22-A114
Electrostatic discharge voltage TA = +25 °C, conforming
VESD(CDM)
C4
(charge device model)
to ANSI/ESD STM5.3.1
1. Data based on characterization results, not tested in production.
Static latch-up
Two complementary static tests are required on six parts to assess the latch-up
performance:
•
•
A supply overvoltage is applied to each power supply pin.
A current injection is applied to each input, output and configurable I/O pin.
These tests are compliant with EIA/JESD 78A IC latch-up standard.
Table 45. Electrical sensitivities
Symbol
Parameter
Conditions
Class
II level A
LU
Static latch-up class
TA = +105 °C conforming to JESD78A
6.3.12
I/O current injection characteristics
As a general rule, current injection to the I/O pins, due to external voltage below V or
SS
above V
(for standard, 3.3 V-capable I/O pins) should be avoided during normal
DDIOx
product operation. However, in order to give an indication of the robustness of the
microcontroller in cases when abnormal injection accidentally happens, susceptibility tests
are performed on a sample basis during device characterization.
Functional susceptibility to I/O current injection
While a simple application is executed on the device, the device is stressed by injecting
current into the I/O pins programmed in floating input mode. While current is injected into
the I/O pin, one at a time, the device is checked for functional failures.
The failure is indicated by an out of range parameter: ADC error above a certain limit (higher
than 5 LSB TUE), out of conventional limits of induced leakage current on adjacent pins (out
of the -5 µA/+0 µA range) or other functional failure (for example reset occurrence or
oscillator frequency deviation).
The characterization results are given in Table 46.
Negative induced leakage current is caused by negative injection and positive induced
leakage current is caused by positive injection.
64/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
Table 46. I/O current injection susceptibility
Functional
susceptibility
Symbol
Description
Unit
Negative Positive
injection injection
Injected current on PA12 pin
-0
-5
+5
Injected current on PA9, PB3, PB13, PF11 pins with induced
leakage current on adjacent pins less than 50 µA
NA
IINJ
mA
Injected current on PB0, PB1 and all other FT and FTf pins,
and on NPOR pin
-5
-5
NA
+5
Injected current on all other TC, TTa and RST pins
6.3.13
I/O port characteristics
General input/output characteristics
Unless otherwise specified, the parameters given in Table 47 are derived from tests
performed under the conditions summarized in Table 20: General operating conditions. All
I/Os are designed as CMOS- and TTL-compliant.
Table 47. I/O static characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
TC and TTa I/O
FT and FTf I/O
All I/Os
-
-
0.3 VDDIOx+0.07(1)
Low level input
voltage
VIL
-
-
0.475 VDDIOx–0.2(1)
V
-
-
0.3 VDDIOx
TC and TTa I/O
FT and FTf I/O
All I/Os
0.445 VDDIOx+0.398(1)
-
-
-
-
-
-
High level input
voltage
VIH
0.5 VDDIOx+0.2(1)
-
V
0.7 VDDIOx
-
TC and TTa I/O
FT and FTf I/O
-
-
200(1)
100(1)
Schmitt trigger
hysteresis
Vhys
mV
TC, FT and FTf I/O
TTa in digital mode
VSS ≤ VIN ≤ VDDIOx
-
-
± 0.1
TTa in digital mode
VDDIOx ≤ VIN ≤ VDDA
-
-
-
-
-
-
1
Input leakage
current(2)
Ilkg
µA
TTa in analog mode
VSS ≤ VIN ≤ VDDA
± 0.2
10
FT and FTf I/O
VDDIOx ≤ VIN ≤ 5 V
Weak pull-up
RPU
equivalent resistor VIN = VSS
25
40
55
kΩ
(3)
DocID026007 Rev 6
65/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
Table 47. I/O static characteristics (continued)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Weak pull-down
equivalent
RPD
CIO
VIN = - VDDIOx
-
25
-
40
5
55
-
kΩ
resistor(3)
I/O pin capacitance
pF
1. Data based on design simulation only. Not tested in production.
2. The leakage could be higher than the maximum value, if negative current is injected on adjacent pins. Refer to Table 46:
I/O current injection susceptibility.
3. Pull-up and pull-down resistors are designed with a true resistance in series with a switchable PMOS/NMOS. This
PMOS/NMOS contribution to the series resistance is minimal (~10% order).
All I/Os are CMOS- and TTL-compliant (no software configuration required). Their
characteristics cover more than the strict CMOS-technology or TTL parameters. The
coverage of these requirements is shown in Figure 18 for standard I/Os, and in Figure 19 for
5 V-tolerant I/Os. The following curves are design simulation results, not tested in
production.
66/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
Figure 18. TC and TTa I/O input characteristics
ꢀ
ꢆꢇꢍ
ꢆ
7(67('ꢀ5$1*(
77/ꢄVWDQGDUGꢄUHTXLUHPHQW
9,1ꢀꢄ9ꢅ
ꢌꢇꢍ
81'(),1('ꢀ,1387ꢀ5$1*(
ꢌ
77/ꢄVWDQGDUGꢄUHTXLUHPHQW
ꢎꢇꢍ
ꢎ
7(67('ꢀ5$1*(
ꢌꢇꢒ
ꢌꢇꢃ
ꢆꢇꢎ
ꢆꢇꢆ
ꢆꢇꢁ
ꢆꢇꢒ
ꢆꢇꢃ
ꢀꢇꢎ
ꢀꢇꢆ
ꢀꢇꢁ
ꢀꢇꢒ
9'',2[ꢀꢄ9ꢅ
06Yꢀꢆꢌꢀꢎ9ꢁ
Figure 19. Five volt tolerant (FT and FTf) I/O input characteristics
ꢀ
ꢆꢇꢍ
ꢆ
7(67('ꢀ5$1*(
77/ꢄVWDQGDUGꢄUHTXLUHPHQW
9,1ꢀꢄ9ꢅ
ꢌꢇꢍ
81'(),1('ꢀ,1387ꢀ5$1*(
ꢌ
77/ꢄVWDQGDUGꢄUHTXLUHPHQW
ꢎꢇꢍ
ꢎ
7(67('ꢀ5$1*(
ꢌꢇꢒ
ꢌꢇꢃ
ꢆꢇꢎ
ꢆꢇꢆ
ꢆꢇꢁ
ꢆꢇꢒ
ꢆꢇꢃ
ꢀꢇꢎ
ꢀꢇꢆ
ꢀꢇꢁ
ꢀꢇꢒ
9'',2[ꢀꢄ9ꢅ
06Yꢀꢆꢌꢀꢌ9ꢁ
DocID026007 Rev 6
67/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
Output driving current
The GPIOs (general purpose input/outputs) can sink or source up to +/-8 mA, and sink or
source up to +/- 20 mA (with a relaxed V /V ).
OL OH
In the user application, the number of I/O pins which can drive current must be limited to
respect the absolute maximum rating specified in Section 6.2:
•
The sum of the currents sourced by all the I/Os on V
, plus the maximum
DDIOx
consumption of the MCU sourced on V , cannot exceed the absolute maximum rating
DD
ΣI
(see Table 17: Voltage characteristics).
VDD
•
The sum of the currents sunk by all the I/Os on V , plus the maximum consumption of
SS
the MCU sunk on V , cannot exceed the absolute maximum rating ΣI
(see
SS
VSS
Table 17: Voltage characteristics).
Output voltage levels
Unless otherwise specified, the parameters given in the table below are derived from tests
performed under the ambient temperature and supply voltage conditions summarized in
Table 20: General operating conditions. All I/Os are CMOS- and TTL-compliant (FT, TTa or
TC unless otherwise specified).
(1)
Table 48. Output voltage characteristics
Symbol
VOL
Parameter
Conditions
Min
Max Unit
Output low level voltage for an I/O pin
Output high level voltage for an I/O pin
Output low level voltage for an I/O pin
Output high level voltage for an I/O pin
CMOS port(2)
|IIO| = 8 mA
VDDIOx ≥ 2.7 V
-
0.4
V
VOH
VDDIOx–0.4
-
VOL
TTL port(2)
|IIO| = 8 mA
VDDIOx ≥ 2.7 V
-
0.4
V
VOH
2.4
-
(3)
VOL
Output low level voltage for an I/O pin
Output high level voltage for an I/O pin
Output low level voltage for an I/O pin
Output high level voltage for an I/O pin
Output low level voltage for an I/O pin
Output high level voltage for an I/O pin
-
1.3
V
|IIO| = 20 mA
VDDIOx ≥ 2.7 V
(3)
VOH
VDDIOx–1.3
-
(3)
VOL
-
0.4
V
-
|IIO| = 6 mA
(3)
VDDIOx ≥ 2 V
VOH
VDDIOx–0.4
-
(4)
VOL
0.4
-
V
V
|IIO| = 4 mA
(4)
VOH
VDDIOx–0.4
|IIO| = 20 mA
VDDIOx ≥ 2.7 V
-
-
0.4
0.4
V
V
Output low level voltage for an FTf I/O pin in
Fm+ mode
(3)
VOLFm+
|IIO| = 10 mA
1. The IIO current sourced or sunk by the device must always respect the absolute maximum rating specified in Table 17:
Voltage characteristics, and the sum of the currents sourced or sunk by all the I/Os (I/O ports and control pins) must always
respect the absolute maximum ratings ΣI
.
IO
2. TTL and CMOS outputs are compatible with JEDEC standards JESD36 and JESD52.
3. Data based on characterization results. Not tested in production.
4. Data based on characterization results. Not tested in production.
68/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Input/output AC characteristics
Electrical characteristics
The definition and values of input/output AC characteristics are given in Figure 20 and
Table 49, respectively. Unless otherwise specified, the parameters given are derived from
tests performed under the ambient temperature and supply voltage conditions summarized
in Table 20: General operating conditions.
(1)(2)
Table 49. I/O AC characteristics
OSPEEDRy
[1:0] value(1)
Symbol
Parameter
Conditions
Min
Max
Unit
MHz
ns
fmax(IO)out Maximum frequency(3)
tf(IO)out Output fall time
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
2
125
125
1
CL = 50 pF, VDDIOx ≥ 2 V
tr(IO)out Output rise time
fmax(IO)out Maximum frequency(3)
tf(IO)out Output fall time
x0
MHz
ns
CL = 50 pF, VDDIOx < 2 V
CL = 50 pF, VDDIOx ≥ 2 V
CL = 50 pF, VDDIOx < 2 V
125
125
10
25
25
4
tr(IO)out Output rise time
fmax(IO)out Maximum frequency(3)
tf(IO)out Output fall time
MHz
ns
tr(IO)out Output rise time
fmax(IO)out Maximum frequency(3)
tf(IO)out Output fall time
01
MHz
ns
62.5
62.5
50
30
20
10
5
tr(IO)out Output rise time
CL = 30 pF, VDDIOx ≥ 2.7 V
CL = 50 pF, VDDIOx ≥ 2.7 V
CL = 50 pF, 2 V ≤ VDDIOx < 2.7 V
CL = 50 pF, VDDIOx < 2 V
fmax(IO)out Maximum frequency(3)
MHz
CL = 30 pF, VDDIOx ≥ 2.7 V
CL = 50 pF, VDDIOx ≥ 2.7 V
CL = 50 pF, 2 V ≤ VDDIOx < 2.7 V
CL = 50 pF, VDDIOx < 2 V
8
11
tf(IO)out Output fall time
12
25
5
ns
CL = 30 pF, VDDIOx ≥ 2.7 V
CL = 50 pF, VDDIOx ≥ 2.7 V
CL = 50 pF, 2 V ≤ VDDIOx < 2.7 V
CL = 50 pF, VDDIOx < 2 V
8
tr(IO)out Output rise time
12
25
DocID026007 Rev 6
69/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
(1)(2)
Table 49. I/O AC characteristics
Parameter
(continued)
OSPEEDRy
Symbol
Conditions
Min
Max
Unit
MHz
ns
[1:0] value(1)
fmax(IO)out Maximum frequency(3)
tf(IO)out Output fall time
-
-
-
-
-
-
2
CL = 50 pF, VDDIOx ≥ 2 V
12
34
0.5
16
44
Fm+
tr(IO)out Output rise time
fmax(IO)out Maximum frequency(3)
tf(IO)out Output fall time
configuration
(4)
MHz
ns
CL = 50 pF, VDDIOx < 2 V
tr(IO)out Output rise time
Pulse width of external
tEXTIpw signals detected by the
EXTI controller
-
-
10
-
ns
1. The I/O speed is configured using the OSPEEDRx[1:0] bits. Refer to the STM32F0xxxx RM0091 reference manual for a
description of GPIO Port configuration register.
2. Guaranteed by design, not tested in production.
3. The maximum frequency is defined in Figure 20.
4. When Fm+ configuration is set, the I/O speed control is bypassed. Refer to the STM32F0xxxx reference manual RM0091
for a detailed description of Fm+ I/O configuration.
Figure 20. I/O AC characteristics definition
ꢌꢎꢑ
ꢂꢎꢑ
ꢍꢎꢑ
ꢍꢎꢑ
ꢌꢎꢑ
ꢂꢎꢑ
W
W
Uꢉ,2ꢋRXW
Iꢉ,2ꢋRXW
7
ꢆ
0D[LPXPꢄIUHTXHQF\ꢄLVꢄDFKLHYHGꢄLIꢄꢉWꢄꢄꢊꢄWꢄꢄꢋꢄꢄ 7ꢄDQGꢄLIꢄWKHꢄGXW\ꢄF\FOHꢄLVꢄꢉꢁꢍꢓꢍꢍꢑꢋ
U
I
ꢀ
ZKHQꢄORDGHGꢄE\ꢄ&ꢄꢄꢉVHHꢄWKHꢄWDEOHꢄ,ꢀ2ꢁ$&ꢁFKDUDFWHULVWLFVꢁGHILQLWLRQꢋ
-
06ꢀꢆꢌꢀꢆ9ꢀ
6.3.14
NRST and NPOR pin characteristics
NRST pin characteristics
The NRST pin input driver uses the CMOS technology. It is connected to a permanent pull-
up resistor, R
.
PU
Unless otherwise specified, the parameters given in the table below are derived from tests
performed under the ambient temperature and supply voltage conditions summarized in
Table 20: General operating conditions.
70/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
Table 50. NRST pin characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VIL(NRST) NRST input low level voltage
VIH(NRST) NRST input high level voltage
-
-
-
-
-
0.3 VDD+0.07(1)
-
V
0.445 VDD+0.398(1)
NRST Schmitt trigger voltage
Vhys(NRST)
hysteresis
-
-
200
40
-
mV
Weak pull-up equivalent
RPU
VIN = VSS
25
55
kΩ
resistor(2)
VF(NRST) NRST input filtered pulse
-
-
-
-
-
100(1)
-
ns
ns
VNF(NRST) NRST input not filtered pulse
700(1)
1. Data based on design simulation only. Not tested in production.
2. The pull-up is designed with a true resistance in series with a switchable PMOS. This PMOS contribution to the series
resistance is minimal (~10% order).
Figure 21. Recommended NRST pin protection
([WHUQDO
UHVHWꢄFLUFXLWꢉꢌꢋ
9''
538
1567ꢉꢆꢋ
,QWHUQDOꢄUHVHW
)LOWHU
ꢎꢇꢌꢄ)
06ꢌꢂꢃꢏꢃ9ꢀ
1. The external capacitor protects the device against parasitic resets.
2. The user must ensure that the level on the NRST pin can go below the VIL(NRST) max level specified in
Table 50: NRST pin characteristics. Otherwise the reset will not be taken into account by the device.
NPOR pin characteristics
The NPOR pin input driver uses the CMOS technology. It is connected to a permanent pull-
up resistor to the V
, R
.
DDA
PU
Unless otherwise specified, the parameters given in Table 51 below are derived from tests
performed under ambient temperature and supply voltage conditions summarized in
Table 20: General operating conditions.
DocID026007 Rev 6
71/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
Table 51. NPOR pin characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VIL(NPOR) NPOR Input low level voltage
-
-
-
0.475 VDDA - 0.2(1)
V
NPOR Input high level
VIH(NPOR)
voltage
-
0.5 VDDA + 0.2(1)
-
-
-
NPOR Schmitt trigger voltage
Vhys(NPOR)
hysteresis
-
-
100(1)
40
mV
Weak pull-up equivalent
RPU
VIN = VSS
25
55
kΩ
resistor(2)
1. Guaranteed by design, not tested in production.
2. The pull-up is designed with a true resistance in series with a switchable PMOS. This PMOS contribution to the series
resistance is minimal (~10% order).
6.3.15
12-bit ADC characteristics
Unless otherwise specified, the parameters given in Table 52 are derived from tests
performed under the conditions summarized in Table 20: General operating conditions.
Note:
It is recommended to perform a calibration after each power-up.
Table 52. ADC characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Analog supply voltage for
ADC ON
VDDA
-
2.4
-
3.6
V
Current consumption of
the ADC(1)
IDDA (ADC)
fADC
VDDA = 3.3 V
-
0.9
-
mA
ADC clock frequency
Sampling rate
-
0.6
-
-
14
1
MHz
MHz
(2)
fS
12-bit resolution
0.043
fADC = 14 MHz,
12-bit resolution
-
-
823
kHz
(2)
External trigger frequency
fTRIG
12-bit resolution
-
-
-
-
17
1/fADC
V
VAIN
Conversion voltage range
External input impedance
0
VDDA
See Equation 1 and
Table 53 for details
(2)
RAIN
-
-
-
-
-
-
50
1
kΩ
kΩ
pF
Sampling switch
resistance
(2)
-
-
RADC
Internal sample and hold
capacitor
(2)
8
CADC
f
ADC = 14 MHz
5.9
83
µs
(2)(3)
Calibration time
tCAL
-
1/fADC
72/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
Table 52. ADC characteristics (continued)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
1.5 ADC
cycles + 3
fPCLK cycles
1.5 ADC
cycles + 2
fPCLK cycles
ADC clock = HSI14
-
-
ADC_DR register ready
latency
(2)(4)
WLATENCY
fPCLK
cycle
ADC clock = PCLK/2
-
-
4.5
8.5
-
-
fPCLK
cycle
ADC clock = PCLK/4
f
ADC = fPCLK/2 = 14 MHz
0.196
5.5
µs
1/fPCLK
µs
f
ADC = fPCLK/2
(2)
Trigger conversion latency fADC = fPCLK/4 = 12 MHz
fADC = fPCLK/4
0.219
10.5
-
tlatr
1/fPCLK
µs
fADC = fHSI14 = 14 MHz
0.179
-
0.250
-
ADC jitter on trigger
conversion
JitterADC
f
ADC = fHSI14
1
1/fHSI14
fADC = 14 MHz
0.107
1.5
-
-
17.1
µs
(2)
Sampling time
Stabilization time
tS
-
-
239.5
1/fADC
1/fADC
(2)
tSTAB
14
fADC = 14 MHz,
12-bit resolution
1
-
18
µs
Total conversion time
(including sampling time)
(2)
tCONV
14 to 252 (tS for sampling +12.5 for
successive approximation)
12-bit resolution
1/fADC
1. During conversion of the sampled value (12.5 x ADC clock period), an additional consumption of 100 µA on IDDA and 60 µA
on IDD should be taken into account.
2. Guaranteed by design, not tested in production.
3. Specified value includes only ADC timing. It does not include the latency of the register access.
4. This parameter specify latency for transfer of the conversion result to the ADC_DR register. EOC flag is set at this time.
Equation 1: R
max formula
AIN
TS
RAIN < --------------------------------------------------------------- – RADC
fADC × CADC × ln(2N + 2
)
The formula above (Equation 1) is used to determine the maximum external impedance
allowed for an error below 1/4 of LSB. Here N = 12 (from 12-bit resolution).
Table 53. R
max for f
tS (µs)
= 14 MHz
ADC
AIN
Ts (cycles)
RAIN max (kΩ)(1)
1.5
7.5
0.11
0.54
0.96
0.4
5.9
13.5
11.4
DocID026007 Rev 6
73/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
Table 53. R
max for f
= 14 MHz (continued)
AIN
ADC
Ts (cycles)
tS (µs)
RAIN max (kΩ)(1)
28.5
41.5
55.5
71.5
239.5
2.04
2.96
3.96
5.11
17.1
25.2
37.2
50
NA
NA
1. Guaranteed by design, not tested in production.
(1)(2)(3)
Table 54. ADC accuracy
Symbol
Parameter
Test conditions
Typ
Max(4)
Unit
ET
EO
EG
ED
EL
Total unadjusted error
Offset error
±1.3
±1
±2
±1.5
±1.5
±1
f
PCLK = 48 MHz,
fADC = 14 MHz, RAIN < 10 kΩ
VDDA = 3 V to 3.6 V
TA = 25 °C
Gain error
±0.5
±0.7
±0.8
±3.3
±1.9
±2.8
±0.7
±1.2
±3.3
±1.9
±2.8
±0.7
±1.2
LSB
Differential linearity error
Integral linearity error
Total unadjusted error
Offset error
±1.5
±4
ET
EO
EG
ED
EL
fPCLK = 48 MHz,
fADC = 14 MHz, RAIN < 10 kΩ
±2.8
±3
Gain error
LSB
LSB
VDDA = 2.7 V to 3.6 V
TA = - 40 to 105 °C
Differential linearity error
Integral linearity error
Total unadjusted error
Offset error
±1.3
±1.7
±4
ET
EO
EG
ED
EL
fPCLK = 48 MHz,
fADC = 14 MHz, RAIN < 10 kΩ
±2.8
±3
Gain error
V
DDA = 2.4 V to 3.6 V
Differential linearity error
Integral linearity error
±1.3
±1.7
TA = 25 °C
1. ADC DC accuracy values are measured after internal calibration.
2. ADC Accuracy vs. Negative Injection Current: Injecting negative current on any of the standard (non-robust) analog input
pins should be avoided as this significantly reduces the accuracy of the conversion being performed on another analog
input. It is recommended to add a Schottky diode (pin to ground) to standard analog pins which may potentially inject
negative current.
Any positive injection current within the limits specified for IINJ(PIN) and ΣIINJ(PIN) in Section 6.3.13 does not affect the ADC
accuracy.
3. Better performance may be achieved in restricted VDDA, frequency and temperature ranges.
4. Data based on characterization results, not tested in production.
74/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
Figure 22. ADC accuracy characteristics
966$
ꢁꢎꢂꢍ
(*
ꢉꢌꢋꢄ([DPSOHꢄRIꢄDQꢄDFWXDOꢄWUDQVIHUꢄFXUYH
ꢉꢆꢋꢄ7KHꢄLGHDOꢄWUDQVIHUꢄFXUYH
ꢉꢀꢋꢄ(QGꢄSRLQWꢄFRUUHODWLRQꢄOLQH
ꢁꢎꢂꢁ
ꢁꢎꢂꢀ
(
7
ꢄ ꢄ7RWDOꢄ8QDMXVWHGꢄ(UURUꢅꢄPD[LPXPꢄGHYLDWLRQꢄ
ꢉꢆꢋ
EHWZHHQꢄWKHꢄDFWXDOꢄDQGꢄLGHDOꢄWUDQVIHUꢄFXUYHVꢇ
(7
(2ꢄ ꢄ2IIVHWꢄ(UURUꢅꢄPD[LPXPꢄGHYLDWLRQꢄ
EHWZHHQꢄWKHꢄILUVWꢄDFWXDOꢄWUDQVLWLRQꢄDQGꢄWKHꢄILUVW
LGHDOꢄRQHꢇ
ꢉꢀꢋ
ꢏ
ꢉꢌꢋ
ꢒ
ꢍ
ꢁ
ꢀ
ꢆ
ꢌ
(
*
ꢄ ꢄ*DLQꢄ(UURUꢅꢄGHYLDWLRQꢄEHWZHHQꢄWKHꢄODVWꢄ
LGHDOꢄWUDQVLWLRQꢄDQGꢄWKHꢄODVWꢄDFWXDOꢄRQHꢇ
ꢄ ꢄ'LIIHUHQWLDOꢄ/LQHDULW\ꢄ(UURUꢅꢄPD[LPXPꢄ
GHYLDWLRQꢄEHWZHHQꢄDFWXDOꢄVWHSVꢄDQGꢄWKHꢄLGHDOꢄRQHVꢇ
(2
(/
(
'
('
(/ꢄ ꢄ,QWHJUDOꢄ/LQHDULW\ꢄ(UURUꢅꢄPD[LPXPꢄGHYLDWLRQꢄ
EHWZHHQꢄDQ\ꢄDFWXDOꢄWUDQVLWLRQꢄDQGꢄWKHꢄHQGꢄSRLQWꢄ
FRUUHODWLRQꢄOLQHꢇ
ꢌꢄ/6%ꢄ,'($/
9''$
ꢎ
ꢁꢎꢂꢒ
ꢁꢎꢂꢁ ꢁꢎꢂꢍ
ꢏ
ꢁꢎꢂꢀ
ꢆ
ꢀ
ꢁ
ꢍ
ꢒ
ꢌ
06ꢌꢂꢃꢃꢎ9ꢆ
Figure 23. Typical connection diagram using the ADC
9
''$
6DPSOHꢄDQGꢄKROGꢄ$'&
FRQYHUWHU
9
7
ꢉꢌꢋ
5
$,1
5
$'&
$,1[
ꢌꢆꢓELW
FRQYHUWHU
,/
ꢌ $
ꢉꢆꢋ
SDUDVLWLF
9
7
&
9$,1
&
$'&
06ꢀꢀꢂꢎꢎ9ꢆ
1. Refer to Table 52: ADC characteristics for the values of RAIN, RADC and CADC
.
2. Cparasitic represents the capacitance of the PCB (dependent on soldering and PCB layout quality) plus the
pad capacitance (roughly 7 pF). A high Cparasitic value will downgrade conversion accuracy. To remedy
this, fADC should be reduced.
General PCB design guidelines
Power supply decoupling should be performed as shown in Figure 9: Power supply scheme.
The 10 nF capacitor should be ceramic (good quality) and it should be placed as close as
possible to the chip.
DocID026007 Rev 6
75/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
6.3.16
Temperature sensor characteristics
Table 55. TS characteristics
Symbol
Parameter
VSENSE linearity with temperature
Avg_Slope(1) Average slope
Min
Typ
Max
Unit
(1)
TL
-
4.0
1.34
-
± 1
4.3
1.43
-
± 2
4.6
°C
mV/°C
V
V30
Voltage at 30 °C (± 5 °C)(2)
1.52
10
(1)
(1)
tSTART
ADC_IN16 buffer startup time
µs
ADC sampling time when reading the
temperature
tS_temp
4
-
-
µs
1. Guaranteed by design, not tested in production.
2. Measured at VDDA = 3.3 V ± 10 mV. The V30 ADC conversion result is stored in the TS_CAL1 byte. Refer to Table 2:
Temperature sensor calibration values.
6.3.17
V
monitoring characteristics
BAT
Table 56. V
monitoring characteristics
BAT
Symbol
Parameter
Resistor bridge for VBAT
Min
Typ
Max
Unit
R
Q
-
-
2 x 50
-
-
kΩ
-
Ratio on VBAT measurement
Error on Q
2
-
Er(1)
–1
4
+1
-
%
µs
(1)
tS_vbat
ADC sampling time when reading the VBAT
-
1. Guaranteed by design, not tested in production.
6.3.18
Timer characteristics
The parameters given in the following tables are guaranteed by design.
Refer to Section 6.3.13: I/O port characteristics for details on the input/output alternate
function characteristics (output compare, input capture, external clock, PWM output).
Table 57. TIMx characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tTIMxCLK
ns
-
-
-
-
1
-
-
-
tres(TIM)
Timer resolution time
fTIMxCLK = 48 MHz
-
20.8
Timer external clock
frequency on CH1 to
CH4
fTIMxCLK/2
MHz
fEXT
fTIMxCLK = 48 MHz
-
24
-
MHz
216
tTIMxCLK
-
-
-
-
-
-
-
-
-
16-bit timer maximum
period
fTIMxCLK = 48 MHz
-
1365
µs
tMAX_COUNT
232
tTIMxCLK
32-bit counter
maximum period
fTIMxCLK = 48 MHz
89.48
s
76/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Prescaler divider PR[2:0] bits
Electrical characteristics
(1)
Table 58. IWDG min/max timeout period at 40 kHz (LSI)
Min timeout RL[11:0]=
0x000
Max timeout RL[11:0]=
0xFFF
Unit
/4
/8
0
0.1
0.2
0.4
0.8
1.6
3.2
6.4
409.6
819.2
1
/16
/32
/64
/128
/256
2
1638.4
3276.8
6553.6
13107.2
26214.4
3
4
ms
5
6 or 7
1. These timings are given for a 40 kHz clock but the microcontroller internal RC frequency can vary from 30
to 60 kHz. Moreover, given an exact RC oscillator frequency, the exact timings still depend on the phasing
of the APB interface clock versus the LSI clock so that there is always a full RC period of uncertainty.
Table 59. WWDG min/max timeout value at 48 MHz (PCLK)
Prescaler
WDGTB
Min timeout value
Max timeout value
Unit
1
2
4
8
0
1
2
3
0.0853
0.1706
0.3413
0.6826
5.4613
10.9226
21.8453
43.6906
ms
6.3.19
Communication interfaces
I2C interface characteristics
2
2
The I C interface meets the timings requirements of the I C-bus specification and user
manual rev. 03 for:
•
•
•
Standard-mode (Sm): with a bit rate up to 100 kbit/s
Fast-mode (Fm): with a bit rate up to 400 kbit/s
Fast-mode Plus (Fm+): with a bit rate up to 1 Mbit/s.
2
The I C timings requirements are guaranteed by design when the I2Cx peripheral is
properly configured (refer to Reference manual).
The SDA and SCL I/O requirements are met with the following restrictions: the SDA and
SCL I/O pins are not “true” open-drain. When configured as open-drain, the PMOS
connected between the I/O pin and V
is disabled, but is still present. Only FTf I/O pins
DDIOx
support Fm+ low level output current maximum requirement. Refer to Section 6.3.13: I/O
2
port characteristics for the I C I/Os characteristics.
2
All I C SDA and SCL I/Os embed an analog filter. Refer to the table below for the analog
filter characteristics:
DocID026007 Rev 6
77/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
2
(1)
Table 60. I C analog filter characteristics
Symbol
Parameter
Min
Max
Unit
Maximum width of spikes that are
suppressed by the analog filter
tAF
50(2)
260(3)
ns
1. Guaranteed by design, not tested in production.
2. Spikes with widths below tAF(min) are filtered.
3. Spikes with widths above tAF(max) are not filtered
SPI/I2S characteristics
2
Unless otherwise specified, the parameters given in Table 61 for SPI or in Table 62 for I S
are derived from tests performed under the ambient temperature, f frequency and
PCLKx
supply voltage conditions summarized in Table 20: General operating conditions.
Refer to Section 6.3.13: I/O port characteristics for more details on the input/output alternate
2
function characteristics (NSS, SCK, MOSI, MISO for SPI and WS, CK, SD for I S).
(1)
Table 61. SPI characteristics
Symbol
Parameter
Conditions
Master mode
Min
Max
Unit
-
-
18
18
fSCK
1/tc(SCK)
SPI clock frequency
MHz
Slave mode
tr(SCK)
tf(SCK)
SPI clock rise and fall
time
Capacitive load: C = 15 pF
-
6
ns
ns
%
tsu(NSS)
th(NSS)
tw(SCKH)
NSS setup time
NSS hold time
Slave mode
Slave mode
4Tpclk
-
-
2Tpclk + 10
Master mode, fPCLK = 36 MHz,
presc = 4
SCK high and low time
Data input setup time
Tpclk/2 -2
Tpclk/2 + 1
tw(SCKL)
Master mode
Slave mode
Master mode
Slave mode
4
5
-
tsu(MI)
tsu(SI)
-
th(MI)
th(SI)
4
-
Data input hold time
5
-
(2)
ta(SO)
Data output access time Slave mode, fPCLK = 20 MHz
Data output disable time Slave mode
0
3Tpclk
(3)
tdis(SO)
0
18
tv(SO)
tv(MO)
th(SO)
th(MO)
Data output valid time
Data output valid time
Slave mode (after enable edge)
Master mode (after enable edge)
Slave mode (after enable edge)
Master mode (after enable edge)
-
22.5
-
6
-
11.5
2
Data output hold time
-
SPI slave input clock
duty cycle
DuCy(SCK)
Slave mode
25
75
1. Data based on characterization results, not tested in production.
2. Min time is for the minimum time to drive the output and the max time is for the maximum time to validate the data.
3. Min time is for the minimum time to invalidate the output and the max time is for the maximum time to put the data in Hi-Z
78/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
Figure 24. SPI timing diagram - slave mode and CPHA = 0
166ꢄLQSXW
WFꢉ6&.ꢋ
WKꢉ166ꢋ
WVXꢉ166ꢋ
WZꢉ6&.+ꢋ
WUꢉ6&.ꢋ
&3+$ ꢎ
&32/ ꢎ
&3+$ ꢎ
&32/ ꢌ
WDꢉ62ꢋ
WZꢉ6&./ꢋ
WYꢉ62ꢋ
WKꢉ62ꢋ
WIꢉ6&.ꢋ
/DVWꢄELWꢄ287
WGLVꢉ62ꢋ
0,62ꢄRXWSXW
026,ꢄLQSXW
)LUVWꢄELWꢄ287
WKꢉ6,ꢋ
1H[WꢄELWVꢄ287
WVXꢉ6,ꢋ
)LUVWꢄELWꢄ,1
1H[WꢄELWVꢄ,1
/DVWꢄELWꢄ,1
06Yꢁꢌꢒꢍꢃ9ꢌ
Figure 25. SPI timing diagram - slave mode and CPHA = 1
166ꢄLQSXW
WFꢉ6&.ꢋ
WVXꢉ166ꢋ
WZꢉ6&.+ꢋ
WIꢉ6&.ꢋ
WKꢉ166ꢋ
&3+$ ꢌ
&32/ ꢎ
&3+$ ꢌ
&32/ ꢌ
WDꢉ62ꢋ
WZꢉ6&./ꢋ
WYꢉ62ꢋ
)LUVWꢄELWꢄ287
WVXꢉ6,ꢋ WKꢉ6,ꢋ
)LUVWꢄELWꢄ,1
WKꢉ62ꢋ
1H[WꢄELWVꢄ287
WUꢉ6&.ꢋ
WGLVꢉ62ꢋ
0,62ꢄRXWSXW
026,ꢄLQSXW
/DVWꢄELWꢄ287
1H[WꢄELWVꢄ,1
/DVWꢄELWꢄ,1
06Yꢁꢌꢒꢍꢂ9ꢌ
1. Measurement points are done at CMOS levels: 0.3 VDD and 0.7 VDD
.
DocID026007 Rev 6
79/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
Figure 26. SPI timing diagram - master mode
+LJK
166ꢄLQSXW
W
Fꢉ6&.ꢋ
&3+$ ꢎ
&32/ ꢎ
&3+$ ꢎ
&32/ ꢌ
&3+$ ꢌ
&32/ ꢎ
&3+$ ꢌ
&32/ ꢌ
W
W
W
W
Zꢉ6&.+ꢋ
Zꢉ6&./ꢋ
Uꢉ6&.ꢋ
Iꢉ6&.ꢋ
W
VXꢉ0,ꢋ
0,62
,1387
%,7ꢒꢄ,1
/6%ꢄ,1
06%ꢄ,1
W
Kꢉ0,ꢋ
026,
287387
%,7ꢌꢄ287
/6%ꢄ287
06%ꢄ287
W
W
Kꢉ02ꢋ
Yꢉ02ꢋ
DLꢌꢁꢌꢀꢒF
1. Measurement points are done at CMOS levels: 0.3 VDD and 0.7 VDD
.
2
(1)
Table 62. I S characteristics
Conditions
Symbol
Parameter
Min
Max
Unit
Master mode (data: 16 bits, Audio
frequency = 48 kHz)
1.597
1.601
fCK
1/tc(CK)
I2S clock frequency
MHz
Slave mode
0
-
6.5
tr(CK)
tf(CK)
I2S clock rise time
I2S clock fall time
I2S clock high time
I2S clock low time
WS valid time
10
12
-
Capacitive load CL = 15 pF
-
tw(CKH)
tw(CKL)
tv(WS)
th(WS)
tsu(WS)
th(WS)
306
312
2
Master fPCLK= 16 MHz, audio
frequency = 48 kHz
-
ns
%
Master mode
Master mode
Slave mode
Slave mode
-
WS hold time
2
-
WS setup time
7
-
WS hold time
0
-
I2S slave input clock duty
cycle
DuCy(SCK)
Slave mode
25
75
80/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Electrical characteristics
2
(1)
Table 62. I S characteristics (continued)
Symbol
Parameter
Conditions
Master receiver
Min
Max
Unit
tsu(SD_MR)
tsu(SD_SR)
6
2
-
-
Data input setup time
Data input hold time
Data output valid time
Data output hold time
Slave receiver
(2)
th(SD_MR)
Master receiver
Slave receiver
4
-
(2)
th(SD_SR)
0.5
-
-
ns
(2)
tv(SD_MT)
Master transmitter
Slave transmitter
Master transmitter
Slave transmitter
4
31
-
(2)
tv(SD_ST)
th(SD_MT)
th(SD_ST)
-
0
13
-
1. Data based on design simulation and/or characterization results, not tested in production.
2. Depends on fPCLK. For example, if fPCLK = 8 MHz, then TPCLK = 1/fPLCLK = 125 ns.
2
Figure 27. I S slave timing diagram (Philips protocol)
WFꢉ&.ꢋ
&32/ꢄ ꢄꢎ
&32/ꢄ ꢄꢌ
:6ꢄLQSXW
WKꢉ:6ꢋ
WZꢉ&.+ꢋ
WZꢉ&./ꢋ
WYꢉ6'B67ꢋ
WKꢉ6'B67ꢋ
WVXꢉ:6ꢋ
/6%ꢄWUDQVPLWꢉꢆꢋ
WVXꢉ6'B65ꢋ
06%ꢄWUDQVPLW
06%ꢄUHFHLYH
%LWQꢄWUDQVPLW
WKꢉ6'B65ꢋ
6'WUDQVPLW
6'UHFHLYH
/6%ꢄUHFHLYHꢉꢆꢋ
%LWQꢄUHFHLYH
/6%ꢄUHFHLYH
06Yꢀꢂꢏꢆꢌ9ꢌ
1. Measurement points are done at CMOS levels: 0.3 × VDDIOx and 0.7 × VDDIOx
.
2. LSB transmit/receive of the previously transmitted byte. No LSB transmit/receive is sent before the first
byte.
DocID026007 Rev 6
81/98
83
Electrical characteristics
STM32F048C6 STM32F048G6 STM32F048T6
2
Figure 28. I S master timing diagram (Philips protocol)
ꢂꢎꢑ
ꢌꢎꢑ
WIꢉ&.ꢋ
WUꢉ&.ꢋ
WFꢉ&.ꢋ
&32/ꢄ ꢄꢎ
&32/ꢄ ꢄꢌ
WZꢉ&.+ꢋ
WYꢉ:6ꢋ
WKꢉ:6ꢋ
WZꢉ&./ꢋ
:6ꢄRXWSXW
6'WUDQVPLW
WYꢉ6'B07ꢋ
WKꢉ6'B07ꢋ
/6%ꢄWUDQVPLWꢉꢆꢋ
WVXꢉ6'B05ꢋ
06%ꢄWUDQVPLW
06%ꢄUHFHLYH
%LWQꢄWUDQVPLW
WKꢉ6'B05ꢋ
/6%ꢄWUDQVPLW
6'UHFHLYH
/6%ꢄUHFHLYHꢉꢆꢋ
%LWQꢄUHFHLYH
/6%ꢄUHFHLYH
06Yꢀꢂꢏꢆꢎ9ꢌ
1. Data based on characterization results, not tested in production.
2. LSB transmit/receive of the previously transmitted byte. No LSB transmit/receive is sent before the first
byte.
82/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
USB characteristics
Electrical characteristics
The STM32F048x6 USB interface is fully compliant with the USB specification version 2.0
and is USB-IF certified (for Full-speed device operation).
Table 63. USB electrical characteristics
Symbol
Parameter
Conditions
Min.
Typ
Max.
Unit
USB transceiver operating
voltage
VDDIO2
-
-
-
3.0(1)
-
-
-
3.6
1.0
1.5
V
(2)
tSTARTUP
USB transceiver startup time
µs
Embedded USB_DP pull-up
value during idle
RPUI
1.1
1.26
kΩ
Embedded USB_DP pull-up
value during reception
RPUR
-
2.0
28
2.26
40
2.6
44
Driving high
and low
(2)
ZDRV
Output driver impedance(3)
Ω
1. The STM32F048x6 USB functionality is ensured down to 2.7 V but not the full USB electrical
characteristics which are degraded in the 2.7-to-3.0 V voltage range.
2. Guaranteed by design, not tested in production.
3. No external termination series resistors are required on USB_DP (D+) and USB_DM (D-); the matching
impedance is already included in the embedded driver.
DocID026007 Rev 6
83/98
83
Package information
STM32F048C6 STM32F048G6 STM32F048T6
7
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
®
®
ECOPACK packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
®
ECOPACK is an ST trademark.
7.1
UFQFPN48 package information
UFQFPN48 is a 48-lead, 7x7 mm, 0.5 mm pitch, ultra-thin fine-pitch quad flat package.
Figure 29. UFQFPN48 package outline
3LQꢄꢌꢄLGHQWLILHU
ODVHUꢄPDUNLQJꢄDUHD
'
$
(
<
(
6HDWLQJꢄ
SODQH
7
GGG
$ꢌ
E
H
'HWDLOꢄ<
'
([SRVHGꢄSDGꢄ
DUHD
'ꢆ
ꢌ
/
ꢁꢃ
&ꢄꢎꢇꢍꢎꢎ[ꢁꢍ
SLQꢌꢄFRUQHU
5ꢄꢎꢇꢌꢆꢍꢄW\Sꢇ
'HWDLOꢄ=
(ꢆ
ꢌ
ꢁꢃ
=
$ꢎ%ꢂB0(B9ꢀ
1. Drawing is not to scale.
2. All leads/pads should also be soldered to the PCB to improve the lead/pad solder joint life.
3. There is an exposed die pad on the underside of the UFQFPN package. It is recommended to connect and
solder this back-side pad to PCB ground.
84/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Package information
Table 64. UFQFPN48 package mechanical data
millimeters
inches(1)
Symbol
Min
Typ
Max
Min
Typ
Max
A
A1
D
0.500
0.000
6.900
6.900
5.500
5.500
0.300
-
0.550
0.020
7.000
7.000
5.600
5.600
0.400
0.152
0.250
0.500
-
0.600
0.050
7.100
7.100
5.700
5.700
0.500
-
0.0197
0.0000
0.2717
0.2717
0.2165
0.2165
0.0118
-
0.0217
0.0008
0.2756
0.2756
0.2205
0.2205
0.0157
0.0060
0.0098
0.0197
-
0.0236
0.0020
0.2795
0.2795
0.2244
0.2244
0.0197
-
E
D2
E2
L
T
b
0.200
-
0.300
-
0.0079
-
0.0118
-
e
ddd
-
0.080
-
0.0031
1. Values in inches are converted from mm and rounded to 4 decimal digits.
Figure 30. Recommended footprint for UFQFPN48 package
ꢏꢇꢀꢎ
ꢒꢇꢆꢎ
ꢁꢃ
ꢀꢏ
ꢌ
ꢀꢒ
ꢍꢇꢒꢎ
ꢎꢇꢆꢎ
ꢏꢇꢀꢎ
ꢍꢇꢃꢎ
ꢒꢇꢆꢎ
ꢍꢇꢒꢎ
ꢎꢇꢀꢎ
ꢌꢆ
ꢆꢍ
ꢌꢀ
ꢆꢁ
ꢎꢇꢏꢍ
ꢎꢇꢍꢎ
ꢎꢇꢍꢍ
ꢍꢇꢃꢎ
$ꢎ%ꢂB)3B9ꢆ
1. Dimensions are expressed in millimeters.
DocID026007 Rev 6
85/98
94
Package information
STM32F048C6 STM32F048G6 STM32F048T6
Device marking
The following figure gives an example of topside marking orientation versus pin 1 identifier
location.
Other optional marking or inset/upset marks, which identify the parts throughout supply
chain operations, are not indicated below.
Figure 31. UFQFPN48 package marking example
WƌŽĚƵĐƚꢀ
ŝĚĞŶƚŝĨŝĐĂƚŝŽŶ
;ϭͿ
(6ꢀꢁ)
ꢂꢃꢄ&ꢅ8ꢅ
ꢁĂƚĞꢀĐŽĚĞ
< ::
^ƚĂŶĚĂƌĚꢀ^dꢀůŽŐŽ
ZĞǀŝƐŝŽŶꢀĐŽĚĞ
WŝŶꢀϭꢀŝĚĞŶƚŝĨŝĞƌ
5
D^ϯϳϳϯϱsϭ
1. Parts marked as "ES", "E" or accompanied by an Engineering Sample notification letter, are not yet
qualified and therefore not yet ready to be used in production and any consequences deriving from such
usage will not be at ST charge. In no event, ST will be liable for any customer usage of these engineering
samples in production. ST Quality has to be contacted prior to any decision to use these Engineering
Samples to run qualification activity.
86/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Package information
7.2
WLCSP36 package information
WLCSP36 is a 36-ball, 2.605 x 2.703 mm, 0.4 mm pitch wafer-level chip-scale package.
Figure 32. WLCSP36 package outline
Hꢌ
EEE =
$ꢌꢄEDOOꢄORFDWLRQ
)
H
*
H
$
)
'HWDLOꢄ$
Hꢆ
$ꢀ
$ꢆ
$
ꢒ
ꢌ
%XPSꢄVLGH
6LGHꢄYLHZ
;
ꢁ
<
$ꢀ
%XPS
HHH
$ꢌꢄ
=
$ꢌ
RULHQWDWLRQꢄ
UHIHUHQFH
ꢃ
=
DDD
=
E
EꢄꢉꢀꢒꢄEDOOVꢋ
6HDWLQJꢄSODQH
FFF
= ; <
=
GGG
:DIHUꢄEDFNꢄVLGH
'HWDLOꢄ$
URWDWHGꢄꢂꢎ
ꢂϬ>ͺDꢃͺsϮ
1. Drawing is not to scale.
Table 65. WLCSP36 package mechanical data
millimeters
Typ
inches(1)
Symbol
Min
Max
Min
Typ
Max
A
A1
A2
A3(2)
b(3)
D
0.525
0.555
0.175
0.380
0.025
0.250
2.605
2.703
0.400
2.000
2.000
0.585
0.0207
0.0219
0.0069
0.0150
0.0010
0.0098
0.1026
0.1064
0.0157
0.0787
0.0787
0.0230
-
-
-
-
-
-
-
-
-
-
-
-
0.220
0.280
0.0087
0.0110
2.570
2.640
0.1012
0.1039
E
2.668
2.738
0.1050
0.1078
e
-
-
-
-
-
-
-
-
-
-
-
-
e1
e2
DocID026007 Rev 6
87/98
94
Package information
STM32F048C6 STM32F048G6 STM32F048T6
Table 65. WLCSP36 package mechanical data (continued)
millimeters
Typ
inches(1)
Symbol
Min
Max
Min
Typ
Max
F
-
-
-
-
-
-
-
0.3025
-
-
-
-
-
-
-
-
0.0119
-
G
0.3515
-
0.0138
-
aaa
bbb
ccc
ddd
eee
-
-
-
-
-
0.100
0.100
0.100
0.050
0.050
-
-
-
-
-
0.0039
0.0039
0.0039
0.0020
0.0020
1. Values in inches are converted from mm and rounded to 4 decimal digits.
2. Back side coating.
3. Dimension is measured at the maximum bump diameter parallel to primary datum Z.
Figure 33. Recommended pad footprint for WLCSP36 package
'SDG
'VP
06ꢌꢃꢂꢒꢍ9ꢆ
Table 66. WLCSP36 recommended PCB design rules
Dimension
Recommended values
Pitch
Dpad
Dsm
0.4 mm
260 µm max. (circular)
220 µm recommended
300 µm min. (for 260 µm diameter pad)
PCB pad design
Non-solder mask defined via underbump allowed
88/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Device marking
Package information
The following figure gives an example of topside marking orientation versus ball A1 identifier
location.
Other optional marking or inset/upset marks, which identify the parts throughout supply
chain operations, are not indicated below.
Figure 34. WLCSP36 package marking example
ꢁŽƚ
WƌŽĚƵĐƚꢀ
;ϭͿ
ŝĚĞŶƚŝĨŝĐĂƚŝŽŶ
)ꢂꢃꢄ7ꢅ
ZĞǀŝƐŝŽŶꢀĐŽĚĞ
5
ꢁĂƚĞꢀĐŽĚĞ
<
::
D^ϯϳϳϯϰsϭ
1. Parts marked as "ES", "E" or accompanied by an Engineering Sample notification letter, are not yet
qualified and therefore not yet ready to be used in production and any consequences deriving from such
usage will not be at ST charge. In no event, ST will be liable for any customer usage of these engineering
samples in production. ST Quality has to be contacted prior to any decision to use these Engineering
Samples to run qualification activity.
DocID026007 Rev 6
89/98
94
Package information
STM32F048C6 STM32F048G6 STM32F048T6
7.3
UFQFPN28 package information
UFQFPN28 is a 28-lead, 4x4 mm, 0.5 mm pitch, ultra-thin fine-pitch quad flat package.
Figure 35. UFQFPN28 package outline
'HWDLOꢄ<
'
(
'
'ꢌ
(ꢌ
'HWDLOꢄ=
$ꢎ%ꢎB0(B9ꢍ
1. Drawing is not to scale.
(1)
Table 67. UFQFPN28 package mechanical data
millimeters
Typ
inches
Symbol
Min
Max
Min
Typ
Max
A
A1
D
0.500
-
0.550
0.000
4.000
3.000
4.000
3.000
0.400
0.350
0.152
0.250
0.500
0.600
0.050
4.100
3.100
4.100
3.100
0.500
0.450
-
0.0197
-
0.0217
0.0000
0.1575
0.1181
0.1575
0.1181
0.0157
0.0138
0.0060
0.0098
0.0197
0.0236
0.0020
0.1614
0.1220
0.1614
0.1220
0.0197
0.0177
-
3.900
2.900
3.900
2.900
0.300
0.250
-
0.1535
0.1142
0.1535
0.1142
0.0118
0.0098
-
D1
E
E1
L
L1
T
b
0.200
-
0.300
-
0.0079
-
0.0118
-
e
90/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Package information
1. Values in inches are converted from mm and rounded to 4 decimal digits.
Figure 36. Recommended footprint for UFQFPN28 package
ꢀꢇꢀꢎ
ꢎꢇꢍꢎ
ꢎꢇꢆꢌ
ꢀꢇꢆꢎ
ꢎꢇꢆꢎ
ꢁꢇꢀꢎ
ꢀꢇꢀꢎ
ꢀꢇꢆꢎ
ꢎꢇꢆꢌ
ꢎꢇꢀꢎ
ꢎꢇꢍꢎ
ꢎꢇꢍꢍ
ꢎꢇꢍꢎ
ꢀꢇꢀꢎ
$ꢎ%ꢎB)3B9ꢀ
1. Dimensions are expressed in millimeters.
DocID026007 Rev 6
91/98
94
Package information
STM32F048C6 STM32F048G6 STM32F048T6
Device marking
The following figure gives an example of topside marking orientation versus pin 1 identifier
location.
Other optional marking or inset/upset marks, which identify the parts throughout supply
chain operations, are not indicated below.
Figure 37. UFQFPN28 package marking example
WƌŽĚƵĐƚꢀ
ŝĚĞŶƚŝĨŝĐĂƚŝŽŶ
;ϭͿ
)ꢂꢃꢄ*ꢅ
ZĞǀŝƐŝŽŶꢀĐŽĚĞ
ꢁĂƚĞꢀĐŽĚĞ
5
<
::
ꢁŽƚ
D^ϯϳϳϯϯsϭ
1. Parts marked as "ES", "E" or accompanied by an Engineering Sample notification letter, are not yet
qualified and therefore not yet ready to be used in production and any consequences deriving from such
usage will not be at ST charge. In no event, ST will be liable for any customer usage of these engineering
samples in production. ST Quality has to be contacted prior to any decision to use these Engineering
Samples to run qualification activity.
92/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Package information
7.4
Thermal characteristics
The maximum chip junction temperature (T max) must never exceed the values given in
J
Table 20: General operating conditions.
The maximum chip-junction temperature, T max, in degrees Celsius, may be calculated
J
using the following equation:
T max = T max + (P max x Θ )
J
A
D
JA
Where:
•
•
•
•
T max is the maximum ambient temperature in °C,
A
Θ
is the package junction-to-ambient thermal resistance, in °C/W,
JA
P max is the sum of P
max and P max (P max = P
max + P max),
INT I/O
D
INT
I/O
D
P
max is the product of I and V , expressed in Watts. This is the maximum chip
DD DD
INT
internal power.
P
max represents the maximum power dissipation on output pins where:
I/O
P
max = Σ (V × I ) + Σ ((V
– V ) × I ),
DDIOx OH OH
I/O
OL
OL
taking into account the actual V / I and V / I of the I/Os at low and high level in the
OL OL
OH OH
application.
Table 68. Package thermal characteristics
Parameter
Symbol
Value
Unit
Thermal resistance junction-ambient
UFQFPN48 - 7 mm x 7 mm
33
Thermal resistance junction-ambient
WLCSP36 - 2.6 × 2.7 mm
Θ
64
°C/W
JA
Thermal resistance junction-ambient
UFQFPN28 - 4 mm x 4 mm
118
7.4.1
7.4.2
Reference document
JESD51-2 Integrated Circuits Thermal Test Method Environment Conditions - Natural
Convection (Still Air). Available from www.jedec.org
Selecting the product temperature range
When ordering the microcontroller, the temperature range is specified in the ordering
information scheme shown in Section 8: Ordering information.
Each temperature range suffix corresponds to a specific guaranteed ambient temperature at
maximum dissipation and, to a specific maximum junction temperature.
As applications do not commonly use the STM32F048x6 at maximum dissipation, it is useful
to calculate the exact power consumption and junction temperature to determine which
temperature range will be best suited to the application.
The following examples show how to calculate the temperature range needed for a given
application.
DocID026007 Rev 6
93/98
94
Ordering information
STM32F048C6 STM32F048G6 STM32F048T6
8
Ordering information
For a list of available options (memory, package, and so on) or for further information on any
aspect of this device, please contact your nearest ST sales office.
Table 69. Ordering information scheme
Example:
STM32
F
048
C
6
T
6
xxx
Device family
STM32 = ARM-based 32-bit microcontroller
Product type
F = General-purpose
Sub-family
048 = STM32F048xx
Pin count
G = 28 pins
T = 36 pins
C = 48 pins
User code memory size
6 = 32 Kbyte
Package
U = UFQFPN
Y = WLCSP
Temperature range
6 = –40 to 85 °C
7 = –40 to 105 °C
Options
xxx = code ID of programmed parts (includes packing type)
TR = tape and reel packing
blank = tray packing
94/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Revision history
9
Revision history
Table 70. Document revision history
Changes
Date
Revision
27-May-2014
1
Initial release.
Updated the document status to Preliminary data.
No other change in the content.
28-May-2014
2
Removed LQFP48 package.
Updated:
– Table: Typical and maximum current consumption from VDD supply
at VDD = 1.8 V,
– Table: Typical and maximum current consumption from the VDDA
supply,
– Table: Typical and maximum consumption in Stop mode,
– Table: HSI oscillator characteristics,
09-Apr-2015
3
– Figure: HSI oscillator accuracy characterization results for soldered
parts,
– Table: ESD absolute maximum ratings,
– the document status to Datasheet - production data.
Added:
– Figure: UFQFPN48 marking example (package top view),
– Figure: WLCSP36 marking example (package top view),
– Figure: UFQFPN28 marking example (package top view).
Cover page
– 9 timers instead of 8 in the title
– number of I/Os and capacitive sensing channels corrected
– Fast Mode Plus current sink corrected from 20 mA to “extra”
Updates in Section 2: Description:
– updated Figure 1: Block diagram and Figure 2: Clock tree
– Table 1: STM32F048x device features and peripheral counts - I/O
and capacitive channel numbers corrected
Updates in Section 3: Functional overview:
– addition of PB2 to Table 4: Capacitive sensing GPIOs available on
STM32F048x6 devices
06-Nov-2015
4
– addition of the number of complementary outputs for the advanced
control timer and for TIM16, TIM17 general purpose in Table 6:
Timer feature comparison
– removal of USART2 from Figure 3.5.3: Low-power modes
– Table 8: STM32F048x6 I2C implementation - adding “extra”
Updates in Section 4: Pinouts and pin descriptions
– Figure 4: WLCSP36 package updated
– Table 12: STM32F048x6 pin definitions - removal of CIMP1_OUT
and USART4_CTS; swap of F2 and D2 for WLCSP36
– Table 14: Alternate functions selected through GPIOB_AFR
registers for port B - change of I2C2_SDA and I2C2_SCL to
I2C1_SDA and I2C1_SCL
DocID026007 Rev 6
95/98
97
Revision history
STM32F048C6 STM32F048G6 STM32F048T6
Table 70. Document revision history (continued)
Date
Revision
Changes
Updates in Section 5: Memory mapping
– Table 16: STM32F048x6 peripheral register boundary addresses -
change of “SYSCFG + COMP” to “SYSCFG”
Updates in Section 6: Electrical characteristics:
– VDDIOx replacibg VDD in Figure 18: TC and TTa I/O input
characteristics and Figure 19: Five volt tolerant (FT and FTf) I/O
input characteristics
– footnote for VIN max value in Table 17: Voltage characteristics,
– footnote for max VIN in Table 20: General operating conditions,
– addition of tSTART parameter in Table 22: Embedded internal
reference voltage, removal of -40°C to 85°C condition and the
associated footnote
– Table 26: Typical and maximum current consumption from the VBAT
supply: removing “code executing from Flash or RAM”
– removal of the min value for tSTART parameter in Table 55: TS
characteristics
– the typical value for R parameter in Table 56: VBAT monitoring
characteristics
4
– removal of ResTM parameter line from Table 57: TIMx characteristics
and putting all values in new Typ column, substitution of tCOUNTER
with tMAX_COUNT, values defined as powers of two
06-Nov-2015
(continued)
– VESD(CDM) class in Table 44: ESD absolute maximum ratings
– reorganization of Table 62: I2S characteristics and filling max value
of tv(SD_ST)
– adding definition of levels in Figure 28: I2S master timing diagram
(Philips protocol)
Updates in Section 7: Package information:
– heading and display of columns in Table 65: WLCSP36 package
mechanical data.,
– Figure 31: UFQFPN48 package marking example (top view)
– Figure 34: WLCSP36 package marking example (top view)
– Figure 36: Recommended footprint for UFQFPN28 package
distance between corner pads added
– Figure 37: UFQFPN28 package marking example (top view)
– removing “die 445” from Table 68: Package thermal characteristics
Updates in Section 8: Part numbering:
– adding tray packing to options
Section 4: Pinouts and pin descriptions:
– Package pinout figures updated (look and feel)
– Figure 4: WLCSP36 package- now presented in top view
– Table 12: STM32F048x6 pin definitions - note 3 added;
Section 6: Electrical characteristics:
05-Dec-2015
5
– Table 47: I/O static characteristics - removed note
– Section 6.3.15: 12-bit ADC characteristics - changed introductory
sentence
96/98
DocID026007 Rev 6
STM32F048C6 STM32F048G6 STM32F048T6
Revision history
Table 70. Document revision history (continued)
Date
Revision
Changes
Section 6: Electrical characteristics:
– Table 34: LSE oscillator characteristics (fLSE = 32.768 kHz) -
information on configuring different drive capabilities removed. See
the corresponding reference manual.
– Table 22: Embedded internal reference voltage - VREFINT values
10-Jan-2017
6
– Figure 24: SPI timing diagram - slave mode and CPHA = 0 and
Figure 25: SPI timing diagram - slave mode and CPHA = 1
enhanced and corrected
Section 8: Ordering information:
– The name of the section changed from the previous “Part
numbering”
DocID026007 Rev 6
97/98
97
STM32F048C6 STM32F048G6 STM32F048T6
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2017 STMicroelectronics – All rights reserved
98/98
DocID026007 Rev 6
相关型号:
STM32F050C4
Low- and medium-density advanced ARM-based 32-bit MCU with up to 32 Kbytes Flash, timers, ADC and comm. interfaces
STMICROELECTR
STM32F050C4T6A
Low- and medium-density advanced ARMâ¢-based 32-bit MCU with up to 32 Kbytes Flash, timers, ADC and comm. interfaces
STMICROELECTR
STM32F050C6
Low- and medium-density advanced ARM-based 32-bit MCU with up to 32 Kbytes Flash, timers, ADC and comm. interfaces
STMICROELECTR
STM32F050C6T6A
Low- and medium-density advanced ARM-based 32-bit MCU with up to 32 Kbytes Flash, timers, ADC and comm. interfaces
STMICROELECTR
STM32F050F4
Low- and medium-density advanced ARM-based 32-bit MCU with up to 32 Kbytes Flash, timers, ADC and comm. interfaces
STMICROELECTR
STM32F050F6
Low- and medium-density advanced ARM-based 32-bit MCU with up to 32 Kbytes Flash, timers, ADC and comm. interfaces
STMICROELECTR
STM32F050G4
Low- and medium-density advanced ARM-based 32-bit MCU with up to 32 Kbytes Flash, timers, ADC and comm. interfaces
STMICROELECTR
STM32F050G6
Low- and medium-density advanced ARM-based 32-bit MCU with up to 32 Kbytes Flash, timers, ADC and comm. interfaces
STMICROELECTR
STM32F050K4
Low- and medium-density advanced ARM-based 32-bit MCU with up to 32 Kbytes Flash, timers, ADC and comm. interfaces
STMICROELECTR
STM32F050K4U6A
Low- and medium-density advanced ARM-based 32-bit MCU with up to 32 Kbytes Flash, timers, ADC and comm. interfaces
STMICROELECTR
©2020 ICPDF网 联系我们和版权申明