ST485XDR [STMICROELECTRONICS]
Low power RS-485/RS-422 transceiver; 低功耗RS - 485 / RS - 422收发器型号: | ST485XDR |
厂家: | ST |
描述: | Low power RS-485/RS-422 transceiver |
文件: | 总19页 (文件大小:546K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ST485
Low power
RS-485/RS-422 transceiver
General features
I Low quiescent current: 300mA
I Designed for RS-485 interface application
I -7V to 12V common mode input voltage range
I Driver maintains high impedance in 3-state or
with the power OFF
I 70mV tipycal input hysteresis
I 30ns propagation delay, 5ns skew
I Operate from a single 5V supply
DIP-8
SO-8
I Current limiting and thermal shutdown for
driver overload protection
I Allows up to 64 transceivers on the bus
Description
Driver is short-circuit current limited and is
protected against excessive power dissipation by
thermal shutdown circuitry that placed the driver
outputs into a high-impedance state.
The ST485 is al low power transceiver for RS-485
and RS-422 communication. Each part contains
one driver and one receiver.
The ST485 is designed for bi-directional data
communications on multipoint bus transmission
line (half-duplex applciations).
This transceiver draw 300mA (typ.) of supply
current when unloaded or fully loaded with
disabled drivers.
The ST485 is available in three temperature
range: commercial (0°C to 70°C), industrial (-
40°C to 850°C) and automotive (-55°C to 125°C)
It operates from a single 5V supply.
Order code
Part number
Temperature range
Package
Comments
ST485CN
ST485BN
ST485XN
ST485CD
ST485BD
ST485CDR
ST485BDR
ST485XDR
0 to 70 °C
-40 to 85 °C
-55 to 125 °C
0 to 70 °C
DIP-8
DIP-8
50parts per tube / 40tube per box
50parts per tube / 40tube per box
50parts per tube / 40tube per box
100parts per tube / 20tube per box
100parts per tube / 20tube per box
2500 parts per reel
DIP-8
SO-8 (Tube)
SO-8 (Tube)
SO-8 (Tape & reel)
SO-8 (Tape & reel)
SO-8 (Tape & reel)
-40 to 85 °C
0 to 70 °C
-40 to 85 °C
-55 to 125 °C
2500 parts per reel
2500 parts per reel
March 2006
Rev 12
1/19
www.st.com
19
Contents
ST485
Contents
1
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
3
4
Truth tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.1
4.2
Driver switching characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Receiver switching characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5
6
7
Test circuit and typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2/19
ST485
Pin configuration
1
Pin configuration
Figure 1.
Pin configuration
1.1
Pin description
Table 1.
Pin description
Pin n°
Symbol
Name and function
1
2
3
4
5
RO
RE
Receiver Output
Receiver Output Enable
Driver Output Enable
Driver Input
DE
DI
GND
Ground
Non-inverting Receiver Input and Non-inverting
Driver Output
6
A
B
7
8
Inverting Receiver Input and Inverting Driver Output
Supply Voltage
V
CC
3/19
Truth tables
ST485
2
Truth tables
Table 2.
Truth table (driver)
Inputs
Outputs
RE
DE
DI
B
A
X
X
X
H
H
L
H
L
L
H
Z
H
L
X
Z
Note:
X = Don’t care; Z = High impedance
Table 3.
Truth table (receiver)
Inputs
Outputs
RO
RE
DE
A-B
L
L
L
L
≥ +0.2V
≤ -0.2V
H
L
L
L
L
INPUTS OPEN
X
H
Z
H
Note:
X = Don’t care; Z = High impedance
4/19
ST485
Maximum ratings
3
Maximum ratings
Table 4.
Symbol
Absolute maximum ratings
Parameter
Value
Unit
V
Supply Voltage
7
V
CC
V
Control Input Voltage (RE, DE)
Driver Input Voltage (DI)
Driver Output Voltage (A, B)
Receiver Input Voltage (A, B)
Receiver Output Voltage (RO)
-0.5 to (V + 0.5)
V
V
V
V
V
I
CC
V
-0.5 to (V + 0.5)
DI
CC
V
V
± ±14
± ±14
DO
V
RI
-0.5 to (V + 0.5)
RO
CC
Note:
Absolute maximum ratings are those values beyond which damage to the device may occur.
Functional operation under these condition is not implied. V+ and V- can have a maximum
magnitude of +7V, but their absolute addition can not exceed 13 V.
5/19
Electrical characteristics
ST485
4
Electrical characteristics
V
= 5V ± 5%, T = T
to T , unless otherwise specified. Typical values are referred
MAX
CC
A
MIN
to T = 25°C)
A
Table 5.
Symbol
DC Electrical characteristics
Value
(1)
Parameter
Test conditions
-40 to 85 °C
-55 to 125 °C Unit
Min Max
Min
Typ
Max
Differential Driver Output
(No Load)
V
V
5
5
V
OD1
OD2
Differential Driver Output R = 27Ω±(RS-485) (Figure 2.)
(With Load)
5
5
5
5
V
V
L
1.5
1.4
R = 50Ω±(RS-422) (Figure 2.)
L
Change in Magnitude of
Driver Differential Output
Voltage for
Complementary Output
States
∆V
R = 27Ω±or 50Ω±(Figure 2.)
0.2
3
0.2
3
V
V
V
OD
L
Driver Common-Mode
Output Voltage
V
R = 27Ω±or 50Ω±(Figure 2.)
OC
L
Change in Magnitude of
Driver Common-Mode
Output Voltage for
Complementary Output
States
∆V
R = 27Ω±or 50Ω±(Figure 2.)
0.2
0.2
OC
L
V
Input High Voltage
Input Low Voltage
Input Current
RE, DE, DI
RE, DE, DI
RE, DE, DI
2.0
2.0
V
V
IH
V
0.8
0.8
IL
I
± ±2
± ±2
µA
IN1
V
V
V
= 0V or 5.25VV = 0V
DE
= 12V
= -7V
CM
I
Input Current (A, B)
1
-0.8
1
-0.8
mA
mA
IN2
IN
IN
Receiver Differential
Threshold Voltage
V
V
V
= -7 to 12V
= 0V
-0.2
3.5
0.2
-0.2
3.4
0.2
V
mV
V
TH
CM
CM
Receiver Input
Hysteresis
∆V
70
TH
Receiver Output High
Voltage
V
I
I
= -4mAV = 200mV
ID
OH
O
O
Receiver Output Low
Voltage
V
= 4mAV = -200mV
0.4
0.55
V
OL
ID
3-State (High
I
Impedance) Output
Current at Receiver
V
V
= 0.4 to 2.4V
O
± ±1
± ±1
µA
OZR
Receiver Input
Resistance
R
= -7 to 12V
CM
24
24
KW
IN
6/19
ST485
Electrical characteristics
Value
Table 5.
DC Electrical characteristics
(1)
Symbol
Parameter
Test conditions
-40 to 85 °C
-55 to 125 °C Unit
Min Max
Min
Typ
Max
V
V
V
= 0V or V
RE
DE
DE
CC
No Load Supply Current
I
= V
400
300
900
500
900
500
µA
µA
(2)
CC
CC
= 0V
Driver Short-Circuit
(3)
I
I
V
V
V
= -7 to 12V
= -7 to 12V
35
35
7
250
250
95
35
35
7
250
250
95
mA
mA
mA
OSD1
O
O
O
Current, V =High
O
Driver Short-Circuit
(3)
OSD2
Current, V =Low
O
Receiver Short-Circuit
Current
I
= 0V to V
CC
OSR
1. All currents into device pins are positive; all cuttents out of device pins are negative; all voltages are referenced to device
ground unless specified.
2. Supply current specification is valid for loaded transmitters when VDE = 0V
3. Applies to peak current. See typical Operating Characteristics.
4.1
Driver switching characteristics
V
= 5V ± ±5%, T = T
A
to T , unless otherwise specified. Typical values are referred
MAX
CC
A
MIN
to T = 25°C
Table 6.
Symbol
Driver switching characteristics
Value
(1)
Parameter
Test conditions
-40 to 85 °C
-55 to 125°C Unit
Min. Typ. Max. Min. Max.
t
t
Propagation Delay
Input to Output
R
= 54ΩC = C = 100pF
DIFF L1 L2
PLH
10
3
30
5
60
10
40
90
90
90
90
70
10
45
90
90
90
90
ns
ns
ns
ns
ns
ns
ns
(See Figure 4. and Figure 6.)
PHL
R
= 54ΩC = C = 100pF
DIFF
L1
L2
t
Output Skew to Output
Rise or Fall Time
SK
(See Figure 4. and Figure 6.)
R
= 54ΩC = C = 100pF
t
t
DIFF
L1
L2
TLH
THL
15
70
70
70
70
3
(See Figure 4. and Figure 6.)
C = 100pFS2 = Closed
(See Figure 5. and Figure 7.)
L
t
Output Enable Time
Output Enable Time
Output Disable Time
Output Disable Time
PZH
C = 100pFS1 = Closed
(See Figure 5. and Figure 7.)
L
t
PZL
PLZ
PHZ
C = 15pFS1 = Closed
(See Figure 5. and Figure 7.)
L
t
C = 15pFS2 = Closed
(See Figure 5. and Figure 7.)
L
t
1. All currents into device pins are positive; all cuttents out of device pins are negative; all voltages are referenced to device
ground unless specified.
7/19
Electrical characteristics
ST485
4.2
Receiver switching characteristics
V
= 5V ± ±5%, T = T
A
to T , unless otherwise specified. Typical values are referred
MAX
CC
A
MIN
to T = 25°C)
Table 7.
Symbol
Receiver switching characteristics
Value
(1)
Parameter
Test conditions
-40 to 85 °C
-55 to 125°C Unit
Min. Typ. Max. Min. Max.
t
t
Propagation Delay Input
to Output
R
= 54ΩC = C = 100pF
DIFF L1 L2
PLH
20
130
13
20
20
20
20
210
230
ns
ns
ns
ns
ns
(See Figure 4. and Figure 8.)
R = 54ΩC = C = 100pF
DIFF
PHL
Differential Receiver
Skew
L1
L2
t
t
SKD
PZH
(See Figure 4. and Figure 8.)
C
= 15pFS1 = Closed
RL
Output Enable Time
Output Enable Time
Output Disable Time
50
50
50
50
56
56
56
56
(See Fig. 2 and Figure 9.)
C
= 15pFS2 = Closed
RL
t
PZL
PLZ
(See Fig. 2 and Figure 9.)
C
= 15pFS1 = Closed
RL
t
(See Fig. 2 and Figure 9.)
C
= 15pFS2 = Closed
RL
t
Output Disable Time
Maximum Data Rate
ns
PHZ
(See Fig. 2 and Figure 9.)
f
2.5
2.5
Mbps
MAX
1. All currents into device pins are positive; all cuttents out of device pins are negative; all voltages are referenced to device
ground unless specified
8/19
ST485
Test circuit and typical characteristics
5
Test circuit and typical characteristics
Figure 2.
Driver DC test load
Figure 3.
Receiver timing test load
Figure 4.
Drive/receiver timing test circuit
Figure 5.
Driver timing test load
9/19
Test circuit and typical characteristics
ST485
Figure 6.
Driver propagation delay
Figure 7.
Driver enable and disable time
10/19
ST485
Test circuit and typical characteristics
Figure 8.
Receiver propagation delay
Figure 9.
Receiver Enable and Disable Time
11/19
Test circuit and typical characteristics
ST485
Figure 10. Receiver output current vs. output Figure 11. Receiver output current vs. output
low voltage high voltage
Figure 12. Driver output current vs. output low Figure 13. Driver output current vs. output
voltage
high voltage
Figure 14. Supply current vs. temperature
Figure 15. Receiver high level output voltage
vs. temperature
12/19
ST485
Test circuit and typical characteristics
Figure 16. Receiver low level output voltage
vs. temperature
Figure 17. Differential driver output voltage
vs. temperature
13/19
Package mechanical data
ST485
6
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a Lead-free second level interconnect. The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com
14/19
ST485
Package mechanical data
Plastic DIP-8 MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
MAX.
MIN.
TYP.
MAX.
A
a1
B
3.3
0.130
0.7
1.39
0.91
0.028
0.055
0.036
1.65
1.04
0.065
0.041
B1
b
0.5
0.020
b1
D
E
0.38
0.5
9.8
0.015
0.020
0.386
8.8
0.346
0.100
0.300
0.300
e
2.54
7.62
7.62
e3
e4
F
7.1
4.8
0.280
0.189
I
L
3.3
0.130
Z
0.44
1.6
0.017
0.063
P001F
15/19
Package mechanical data
ST485
SO-8 MECHANICAL DATA
mm.
inch
TYP.
DIM.
MIN.
TYP
MAX.
MIN.
MAX.
A
A1
A2
B
1.35
0.10
1.10
0.33
0.19
4.80
3.80
1.75
0.053
0.069
0.010
0.065
0.020
0.010
0.197
0.157
0.25
1.65
0.51
0.25
5.00
4.00
0.04
0.043
0.013
0.007
0.189
0.150
C
D
E
e
1.27
0.050
H
5.80
0.25
0.40
6.20
0.50
1.27
0.228
0.010
0.016
0.244
0.020
0.050
h
L
k
˚ (max.)
8
ddd
0.1
0.04
0016023/C
16/19
ST485
Package mechanical data
Tape & Reel SO-8 MECHANICAL DATA
mm.
TYP
inch
TYP.
DIM.
MIN.
MAX.
330
MIN.
MAX.
12.992
0.519
A
C
12.8
20.2
60
13.2
0.504
0.795
2.362
D
N
T
22.4
8.5
5.9
2.3
4.1
8.1
0.882
0.335
0.232
0.090
0.161
0.319
Ao
Bo
Ko
Po
P
8.1
5.5
2.1
3.9
7.9
0.319
0.216
0.082
0.153
0.311
17/19
Revision history
ST485
7
Revision history
Table 8.
Revision history
Revision
Date
21-Mar-2006
Changes
12
Order codes has been updated and new template.
18/19
ST485
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED,
AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS,
NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR
SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2006 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
19/19
相关型号:
©2020 ICPDF网 联系我们和版权申明