M95512WDW6TP [STMICROELECTRONICS]
512 Kbit Serial SPI bus EEPROMtm with high speed clock; 512 Kbit的串行SPI总线EEPROMTM高速时钟型号: | M95512WDW6TP |
厂家: | ST |
描述: | 512 Kbit Serial SPI bus EEPROMtm with high speed clock |
文件: | 总39页 (文件大小:341K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
M95512-W
M95512-R
512 Kbit Serial SPI bus EEPROM
with high speed clock
Features
■ Compatible with SPI bus serial interface
(Positive clock SPI modes)
■ Single supply voltage:
– 2.5 V to 5.5 V for M95512-W
– 1.8 V to 5.5 V for M95512-R
■ High speed
SO8 (MN)
150 mils width
– 5 MHz clock rate
– 5 ms Write time
■ Status Register
■ Hardware Protection of the Status Register
■ Byte and Page Write (up to 128 bytes)
■ Self-timed programming cycle
■ Adjustable size read-only EEPROM area
■ Enhanced ESD Protection
TSSOP8 (DW)
169 mils width
■ More than 1 000 000 Write cycles
■ More than 40-year data retention
■ Packages
®
– ECOPACK (RoHS compliant)
July 2008
Rev 9
1/39
www.st.com
1
Contents
M95512-W, M95512-R
Contents
1
2
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Signal description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
Serial Data Output (Q) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Serial Data Input (D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Serial Clock (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chip Select (S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hold (HOLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Write Protect (W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
VCC supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
VSS ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3
4
Connecting to the SPI bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1
SPI modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operating features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1
Supply voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1.1
4.1.2
4.1.3
4.1.4
Operating supply voltage V
CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Device reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Power-up conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2
4.3
4.4
4.5
Active Power and Standby Power modes . . . . . . . . . . . . . . . . . . . . . . . . . 13
Hold condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Data Protection and Protocol control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5
6
Memory organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.1
6.2
6.3
Write Enable (WREN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Write Disable (WRDI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Read Status Register (RDSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.3.1
WIP bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2/39
M95512-W, M95512-R
6.3.2
Contents
WEL bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
BP1, BP0 bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SRWD bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.3.3
6.3.4
6.4
6.5
6.6
Write Status Register (WRSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Read from Memory Array (READ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Write to Memory Array (WRITE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7
8
ECC (Error Correction Code) and Write cycling . . . . . . . . . . . . . . . . . . 25
Power-up and delivery state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
8.1
8.2
Power-up state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Initial delivery state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9
Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
10
11
12
13
3/39
List of tables
M95512-W, M95512-R
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Write-Protected block size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Instruction set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Status Register format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Protection modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Operating conditions (M95512-W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Operating conditions (M95512-R). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
AC measurement conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
DC characteristics (M95512-W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
DC characteristics (M95128-R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
AC characteristics (M95512-W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
AC characteristics (M95512-R). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
SO8N – 8 lead plastic small outline, 150 mils body width, package
mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
TSSOP8 – 8 lead thin shrink small outline, package mechanical data. . . . . . . . . . . . . . . . 34
Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Available M95512x products (package, voltage range, temperature grade) . . . . . . . . . . . 36
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 16.
Table 17.
Table 18.
Table 19.
4/39
M95512-W, M95512-R
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SO and TSSOP connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Bus master and memory devices on the SPI bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SPI modes supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Hold condition activation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Write Enable (WREN) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Write Disable (WRDI) sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Read Status Register (RDSR) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 10. Write Status Register (WRSR) sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 11. Read from Memory Array (READ) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 12. Byte Write (WRITE) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 13. Page Write (WRITE) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 14. AC measurement I/O waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 15. Serial input timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 16. Hold timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 17. Serial output timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 18. SO8N – 8 lead plastic small outline, 150 mils body width, package outline . . . . . . . . . . . . 33
Figure 19. TSSOP8 – 8 lead thin shrink small outline, package outline . . . . . . . . . . . . . . . . . . . . . . . 34
5/39
Description
M95512-W, M95512-R
1
Description
These electrically erasable programmable memory (EEPROM) devices are accessed by a
high speed SPI-compatible bus. The memory array is organized as 65536 x 8 bit.
The device is accessed by a simple serial interface that is SPI-compatible. The bus signals
are C, D and Q, as shown in Table 1 and Figure 1.
The device is selected when Chip Select (S) is taken low. Communications with the device
can be interrupted using Hold (HOLD).
Figure 1.
Logic diagram
V
CC
D
C
S
Q
M95xxx
W
HOLD
V
SS
AI01789C
Table 1.
Signal names
Signal name
Function
Direction
C
Serial Clock
Serial Data Input
Serial Data Output
Chip Select
Write Protect
Hold
Input
Input
Output
Input
Input
Input
D
Q
S
W
HOLD
VCC
VSS
Supply voltage
Ground
6/39
M95512-W, M95512-R
Figure 2.
Description
SO and TSSOP connections
M95xxx
S
Q
1
8
V
CC
HOLD
2
3
4
7
W
6
5
C
D
V
SS
AI01790D
1. See Section 11: Package mechanical data for package dimensions, and how to identify pin-1.
7/39
Signal description
M95512-W, M95512-R
2
Signal description
During all operations, V must be held stable and within the specified valid range:
CC
V
(min) to V (max).
CC
CC
All of the input and output signals must be held high or low (according to voltages of V ,
IH
V
, V or V , as specified in Table 11 and Table 12). These signals are described next.
OH
IL OL
2.1
2.2
Serial Data Output (Q)
This output signal is used to transfer data serially out of the device. Data is shifted out on the
falling edge of Serial Clock (C).
Serial Data Input (D)
This input signal is used to transfer data serially into the device. It receives instructions,
addresses, and the data to be written. Values are latched on the rising edge of Serial Clock
(C).
2.3
2.4
Serial Clock (C)
This input signal provides the timing of the serial interface. Instructions, addresses, or data
present at Serial Data Input (D) are latched on the rising edge of Serial Clock (C). Data on
Serial Data Output (Q) changes after the falling edge of Serial Clock (C).
Chip Select (S)
When this input signal is high, the device is deselected and Serial Data Output (Q) is at high
impedance. Unless an internal Write cycle is in progress, the device will be in the Standby
Power mode. Driving Chip Select (S) low selects the device, placing it in the Active Power
mode.
After Power-up, a falling edge on Chip Select (S) is required prior to the start of any
instruction.
2.5
Hold (HOLD)
The Hold (HOLD) signal is used to pause any serial communications with the device without
deselecting the device.
During the Hold condition, the Serial Data Output (Q) is high impedance, and Serial Data
Input (D) and Serial Clock (C) are Don’t Care.
To start the Hold condition, the device must be selected, with Chip Select (S) driven low.
8/39
M95512-W, M95512-R
Signal description
2.6
Write Protect (W)
The main purpose of this input signal is to freeze the size of the area of memory that is
protected against Write instructions (as specified by the values in the BP1 and BP0 bits of
the Status Register).
This pin must be driven either high or low, and must be stable during all write instructions.
2.7
2.8
VCC supply voltage
V
is the supply voltage.
CC
VSS ground
V
is the reference for the V supply voltage.
CC
SS
9/39
Connecting to the SPI bus
M95512-W, M95512-R
3
Connecting to the SPI bus
These devices are fully compatible with the SPI protocol.
All instructions, addresses and input data bytes are shifted in to the device, most significant
bit first. The Serial Data Input (D) is sampled on the first rising edge of the Serial Clock (C)
after Chip Select (S) goes low.
All output data bytes are shifted out of the device, most significant bit first. The Serial Data
Output (Q) is latched on the first falling edge of the Serial Clock (C) after the instruction
(such as the Read from Memory Array and Read Status Register instructions) have been
clocked into the device.
Figure 3.
Bus master and memory devices on the SPI bus
VSS
VCC
R
SDO
SPI Interface with
(CPOL, CPHA) =
(0, 0) or (1, 1)
SDI
SCK
VCC
VCC
VCC
C
Q
D
C
Q
D
C Q D
VSS
VSS
VSS
SPI Bus Master
SPI Memory
Device
SPI Memory
Device
SPI Memory
Device
R
R
R
CS3 CS2 CS1
S
S
S
W
HOLD
W
HOLD
HOLD
W
AI12836b
1. The Write Protect (W) and Hold (HOLD) signals should be driven, high or low as appropriate.
Figure 3 shows an example of three memory devices connected to an MCU, on an SPI bus.
Only one device is selected at a time, so only one device drives the Serial Data Output (Q)
line at a time, the other devices are high impedance.
The pull-up resistor R (represented in Figure 3) ensures that no device is selected if the Bus
Master leaves the S line in the high impedance state.
In applications where the Bus Master might enter a state where all inputs/outputs SPI lines
are in high impedance at the same time (for example, if the Bus Master is reset during the
transmission of an instruction), the clock line (C) must be connected to an external pull-
down resistor so that, if all inputs/outputs become high impedance, the C line is pulled low
(while the S line is pulled high). This ensures that S and C do not become high at the same
time, and so, that the t
requirement is met.
SHCH
10/39
M95512-W, M95512-R
Connecting to the SPI bus
The typical value of R is 100 kΩ, assuming that the time constant R*C (C = parasitic
p
p
capacitance of the bus line) is short enough, as the S and C lines must reach the correct
state (S = high and C = low) while the SPI bus is in high impedance.
Example: C = 50 pF, that is R*C = 5 µs <=> the application must ensure that the Bus
p
p
Master never leaves the SPI bus in the high impedance state for a time period shorter than
5 µs.
3.1
SPI modes
These devices can be driven by a microcontroller with its SPI peripheral running in either of
the two following modes:
●
CPOL=0, CPHA=0
CPOL=1, CPHA=1
●
For these two modes, input data is latched in on the rising edge of Serial Clock (C), and
output data is available from the falling edge of Serial Clock (C).
The difference between the two modes, as shown in Figure 4, is the clock polarity when the
bus master is in Stand-by mode and not transferring data:
●
C remains at 0 for (CPOL=0, CPHA=0)
C remains at 1 for (CPOL=1, CPHA=1)
●
Figure 4.
SPI modes supported
CPOL CPHA
C
0
1
0
1
C
D
Q
MSB
MSB
AI01438B
11/39
Operating features
M95512-W, M95512-R
4
Operating features
4.1
Supply voltage (VCC)
4.1.1
Operating supply voltage V
CC
Prior to selecting the memory and issuing instructions to it, a valid and stable V voltage
CC
within the specified [V (min), V (max)] range must be applied (see Table 7 and Table 8.).
CC
CC
This voltage must remain stable and valid until the end of the transmission of the instruction
and, for a Write instruction, until the completion of the internal write cycle (t ). In order to
W
secure a stable DC supply voltage, it is recommended to decouple the V line with a
CC
suitable capacitor (usually of the order of 10 nF to 100 nF) close to the V /V package
CC SS
pins.
4.1.2
Device reset
In order to prevent inadvertent Write operations during power-up, a power-on-reset (POR)
circuit is included. At power-up, the device does not respond to any instruction until V has
CC
reached the POR threshold voltage (this threshold is lower than the minimum V operating
CC
voltage defined in Table 7 and Table 8).
When V passes over the POR threshold, the device is reset and in the following state:
CC
●
in the Standby Power mode
●
deselected (note that when the device is deselected it is necessary to apply a falling
edge on Chip Select (S) prior to issuing any new instruction, otherwise the instruction is
not executed)
●
Status register values:
–
–
–
the Write Enable Latch (WEL) bit is reset to 0
the Write In Progress (WIP) bit is reset to 0
the SRWD, BP1 and BP0 bits remain unchanged (non-volatile bits).
4.1.3
Power-up conditions
When the power supply is turned on, V rises continuously from V to V . During this
CC
SS
CC
time, the Chip Select (S) line is not allowed to float but should follow the V voltage. It is
CC
therefore recommended to connect the S line to V via a suitable pull-up resistor (see
CC
Figure 3).
In addition, the Chip Select (S) input offers a built-in safety feature, as the S input is edge
sensitive as well as level sensitive: after power-up, the device does not become selected
until a falling edge has first been detected on Chip Select (S). This ensures that Chip Select
(S) must have been high, prior to going low to start the first operation.
The V rise time must not vary faster than 1 V/µs.
CC
Important note: When V passes over the POR threshold (see Section 4.1.2: Device
CC
reset), the device is reset and enters the Standby Power mode. However, the device must
not be accessed until V reaches a valid and stable V voltage within the specified
CC
CC
[V (min), V (max)] ranges defined in Table 7 and Table 8.
CC
CC
12/39
M95512-W, M95512-R
Operating features
4.1.4
Power-down
During power-down (continuous decrease in V below the minimum V operating voltage
CC
CC
defined in Table 7 and Table 8), the device must be:
●
deselected (Chip Select (S) should be allowed to follow the voltage applied on V
)
CC
●
in Standby Power mode (that is there should not be any internal write cycle in
progress).
4.2
Active Power and Standby Power modes
When Chip Select (S) is low, the device is selected, and in the Active Power mode. The
device consumes I , as specified in Table 12.
CC
When Chip Select (S) is high, the device is deselected. If a Write cycle is not currently in
progress, the device then goes in to the Standby Power mode, and the device consumption
drops to I
.
CC1
4.3
Hold condition
The Hold (HOLD) signal is used to pause any serial communications with the device without
resetting the clocking sequence.
During the Hold condition, the Serial Data Output (Q) is high impedance, and Serial Data
Input (D) and Serial Clock (C) are Don’t Care.
To enter the Hold condition, the device must be selected, with Chip Select (S) low.
Normally, the device is kept selected, for the whole duration of the Hold condition.
Deselecting the device while it is in the Hold condition, has the effect of resetting the state of
the device, and this mechanism can be used if it is required to reset any processes that had
been in progress.
The Hold condition starts when the Hold (HOLD) signal is driven low at the same time as
Serial Clock (C) already being low (as shown in Figure 5).
The Hold condition ends when the Hold (HOLD) signal is driven high at the same time as
Serial Clock (C) already being low.
Figure 5 also shows what happens if the rising and falling edges are not timed to coincide
with Serial Clock (C) being low.
Figure 5.
Hold condition activation
C
HOLD
Hold
Hold
Condition
Condition
AI02029D
13/39
Operating features
M95512-W, M95512-R
4.4
Status Register
Figure 6 shows the position of the Status Register in the control logic of the device. The
Status Register contains a number of status and control bits that can be read or set (as
appropriate) by specific instructions. See Section 6.3: Read Status Register (RDSR) for a
detailed description of the Status Register bits
4.5
Data Protection and Protocol control
Non-volatile memory devices can be used in environments that are particularly noisy, and
within applications that could experience problems if memory bytes are corrupted.
Consequently, the device features the following data protection mechanisms:
●
Write and Write Status Register instructions are checked that they consist of a number
of clock pulses that is a multiple of eight, before they are accepted for execution.
●
All instructions that modify data must be preceded by a Write Enable (WREN)
instruction to set the Write Enable Latch (WEL) bit. This bit is returned to its reset state
by the following events:
–
–
–
–
Power-up
Write Disable (WRDI) instruction completion
Write Status Register (WRSR) instruction completion
Write (WRITE) instruction completion
●
●
The Block Protect (BP1, BP0) bits in the Status Register allow part of the memory to be
configured as read-only.
The Write Protect (W) signal allows the Block Protect (BP1, BP0) bits in the Status
Register to be protected.
For any instruction to be accepted, and executed, Chip Select (S) must be driven high after
the rising edge of Serial Clock (C) for the last bit of the instruction, and before the next rising
edge of Serial Clock (C).
Two points need to be noted in the previous sentence:
●
The ‘last bit of the instruction’ can be the eighth bit of the instruction code, or the eighth
bit of a data byte, depending on the instruction (except for Read Status Register
(RDSR) and Read (READ) instructions).
●
The ‘next rising edge of Serial Clock (C)’ might (or might not) be the next bus
transaction for some other device on the SPI bus.
Table 2.
Write-Protected block size
Status Register Bits
Array Addresses
Protected
Protected Block
BP1
BP0
0
0
1
1
0
1
0
1
none
none
Upper quarter
Upper half
C000h - FFFFh
8000h - FFFFh
0000h - FFFFh
Whole memory
14/39
M95512-W, M95512-R
Memory organization
5
Memory organization
The memory is organized as shown in Figure 6.
Figure 6.
Block diagram
HOLD
W
High Voltage
Generator
Control Logic
S
C
D
Q
I/O Shift Register
Address Register
and Counter
Data
Register
Status
Register
Size of the
Read only
EEPROM
area
1 Page
X Decoder
AI01272C
15/39
Instructions
M95512-W, M95512-R
6
Instructions
Each instruction starts with a single-byte code, as summarized in Table 3.
If an invalid instruction is sent (one not contained in Table 3), the device automatically
deselects itself.
Table 3.
Instruction set
Instruction
Description
Instruction Format
WREN
WRDI
Write Enable
0000 0110
0000 0100
0000 0101
0000 0001
0000 0011
0000 0010
Write Disable
RDSR
WRSR
READ
WRITE
Read Status Register
Write Status Register
Read from Memory Array
Write to Memory Array
6.1
Write Enable (WREN)
The Write Enable Latch (WEL) bit must be set prior to each WRITE and WRSR instruction.
The only way to do this is to send a Write Enable instruction to the device.
As shown in Figure 7, to send this instruction to the device, Chip Select (S) is driven low,
and the bits of the instruction byte are shifted in, on Serial Data Input (D). The device then
enters a wait state. It waits for a the device to be deselected, by Chip Select (S) being driven
high.
Figure 7.
Write Enable (WREN) sequence
S
0
1
2
3
4
5
6
7
C
D
Q
Instruction
High Impedance
AI02281E
16/39
M95512-W, M95512-R
Instructions
6.2
Write Disable (WRDI)
One way of resetting the Write Enable Latch (WEL) bit is to send a Write Disable instruction
to the device.
As shown in Figure 8, to send this instruction to the device, Chip Select (S) is driven low,
and the bits of the instruction byte are shifted in, on Serial Data Input (D).
The device then enters a wait state. It waits for a the device to be deselected, by Chip Select
(S) being driven high.
The Write Enable Latch (WEL) bit, in fact, becomes reset by any of the following events:
●
●
●
●
Power-up
WRDI instruction execution
WRSR instruction completion
WRITE instruction completion.
Figure 8.
Write Disable (WRDI) sequence
S
0
1
2
3
4
5
6
7
C
D
Q
Instruction
High Impedance
AI03750D
17/39
Instructions
M95512-W, M95512-R
6.3
Read Status Register (RDSR)
The Read Status Register (RDSR) instruction allows the Status Register to be read. The
Status Register may be read at any time, even while a Write or Write Status Register cycle
is in progress. When one of these cycles is in progress, it is recommended to check the
Write In Progress (WIP) bit before sending a new instruction to the device. It is also possible
to read the Status Register continuously, as shown in Figure 9.
The status and control bits of the Status Register are as follows:
6.3.1
6.3.2
6.3.3
WIP bit
The Write In Progress (WIP) bit indicates whether the memory is busy with a Write or Write
Status Register cycle. When set to 1, such a cycle is in progress, when reset to 0 no such
cycle is in progress.
WEL bit
The Write Enable Latch (WEL) bit indicates the status of the internal Write Enable Latch.
When set to 1 the internal Write Enable Latch is set, when set to 0 the internal Write Enable
Latch is reset and no Write or Write Status Register instruction is accepted.
BP1, BP0 bits
The Block Protect (BP1, BP0) bits are non-volatile. They define the size of the area to be
software protected against Write instructions. These bits are written with the Write Status
Register (WRSR) instruction. When one or both of the Block Protect (BP1, BP0) bits is set to
1, the relevant memory area (as defined in Table 4) becomes protected against Write
(WRITE) instructions. The Block Protect (BP1, BP0) bits can be written provided that the
Hardware Protected mode has not been set.
6.3.4
SRWD bit
The Status Register Write Disable (SRWD) bit is operated in conjunction with the Write
Protect (W) signal. The Status Register Write Disable (SRWD) bit and Write Protect (W)
signal allow the device to be put in the Hardware Protected mode (when the Status Register
Write Disable (SRWD) bit is set to 1, and Write Protect (W) is driven low). In this mode, the
non-volatile bits of the Status Register (SRWD, BP1, BP0) become read-only bits and the
Write Status Register (WRSR) instruction is no longer accepted for execution.
Table 4.
Status Register format
b7
b0
SRWD
0
0
0
BP1
BP0
WEL
WIP
Status Register Write Protect
Block Protect Bits
Write Enable Latch Bit
Write In Progress Bit
18/39
M95512-W, M95512-R
Instructions
Figure 9.
Read Status Register (RDSR) sequence
S
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
C
D
Instruction
Status Register Out
Status Register Out
High Impedance
Q
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
MSB
MSB
AI02031E
19/39
Instructions
M95512-W, M95512-R
6.4
Write Status Register (WRSR)
The Write Status Register (WRSR) instruction allows new values to be written to the Status
Register. Before a WRSR instruction can be accepted, a Write Enable (WREN) instruction
must have been executed.
The Write Status Register (WRSR) instruction is issued by driving Chip Select (S) low,
sending the instruction code and the data byte on Serial Data input (D) and driving Chip
Select (S) high. Chip Select (S) must be driven high after the rising edge of Serial Clock (C)
that latches in the eighth bit of the data byte, and before the next rising edge of Serial Clock
(C). Otherwise, the Write Status Register (WRSR) instruction is not executed.
Driving Chip Select (S) high at a byte boundary of the input data triggers the self-timed Write
cycle whose duration is t (specified in Table 13 and Table 14). The instruction sequence is
W
shown in Figure 10.
While the Write Status Register cycle is in progress, the Status Register may still be read to
check the value of the Write In Progress (WIP) bit: the WIP bit is 1 during the self-timed
Write cycle t , and 0 when the Write cycle is complete. The WEL bit (Write Enable Latch) is
W
also reset when the Write cycle t is complete.
W
The Write Status Register (WRSR) instruction allows the user to change the values of the
BP1, BP0 and SRWD bits:
●
The Block Protect (BP1, BP0) bits define the size of the area to be treated as read-only,
as defined in Table 5.
●
The SRWD bit (Status Register Write Disable bit), depending on the signal applied on
the Write Protect pin (W), allows the user to set or reset the write protection mode of
the Status Register. When the Status Register is in the Write-protected mode, the Write
Status Register (WRSR) instruction is not executed.
The contents of the SRWD and BP1, BP0 bits are updated upon completion of the WRSR
instruction (after t ).
W
The Write Status Register (WRSR) instruction has no effect on Status Register bits b6, b5,
b4, b1, b0. They are always read as 0.
Figure 10. Write Status Register (WRSR) sequence
S
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
C
Instruction
Status
Register In
7
6
5
4
3
2
0
1
D
Q
High Impedance
MSB
AI02282D
20/39
M95512-W, M95512-R
Table 5.
Instructions
Protection modes
Memory content
W
Signal
SRWD
Bit
Write Protection of the
Mode
Status Register
Protected area(1) Unprotected area(1)
1
0
0
0
Status Register is Writable
(if the WREN instruction
has set the WEL bit)
Software
Protected
(SPM)
Ready to accept
Write Protected
Write instructions
The values in the BP1 and
BP0 bits can be changed
1
1
Status Register is
Hardware write protected
Hardware
Protected
(HPM)
Ready to accept
Write Protected
0
1
The values in the BP1 and
BP0 bits cannot be
changed
Write instructions
1. As defined by the values in the Block Protect (BP1, BP0) bits of the Status Register, as shown in Table 2.
The protection features of the device are summarized in Table 5.
When the Status Register Write Disable (SRWD) bit of the Status Register is 0 (its initial
delivery state), it is possible to write to the Status Register provided that the Write Enable
Latch (WEL) bit has previously been set by a Write Enable (WREN) instruction, regardless
of the whether Write Protect (W) is driven high or low.
When the Status Register Write Disable (SRWD) bit of the Status Register is set to 1, two
cases need to be considered, depending on the state of Write Protect (W):
●
●
If Write Protect (W) is driven high, it is possible to write to the Status Register provided
that the Write Enable Latch (WEL) bit has previously been set by a Write Enable
(WREN) instruction.
If Write Protect (W) is driven low, it is not possible to write to the Status Register even if
the Write Enable Latch (WEL) bit has previously been set by a Write Enable (WREN)
instruction. (Attempts to write to the Status Register are rejected, and are not accepted
for execution). As a consequence, all the data bytes in the memory area that are
software protected (SPM) by the Block Protect (BP1, BP0) bits of the Status Register,
are also hardware protected against data modification.
Regardless of the order of the two events, the Hardware Protected Mode (HPM) can be
entered:
●
by setting the Status Register Write Disable (SRWD) bit after driving Write Protect (W)
low
●
or by driving Write Protect (W) low after setting the Status Register Write Disable
(SRWD) bit.
The only way to exit the Hardware Protected Mode (HPM) once entered is to pull Write
Protect (W) high.
If Write Protect (W) is permanently tied high, the Hardware Protected Mode (HPM) can
never be activated, and only the Software Protected Mode (SPM), using the Block Protect
(BP1, BP0) bits of the Status Register, can be used.
21/39
Instructions
M95512-W, M95512-R
6.5
Read from Memory Array (READ)
As shown in Figure 11, to send this instruction to the device, Chip Select (S) is first driven
low. The bits of the instruction byte and address bytes are then shifted in, on Serial Data
Input (D). The address is loaded into an internal address register, and the byte of data at
that address is shifted out, on Serial Data Output (Q).
If Chip Select (S) continues to be driven low, the internal address register is automatically
incremented, and the byte of data at the new address is shifted out.
When the highest address is reached, the address counter rolls over to zero, allowing the
Read cycle to be continued indefinitely. The whole memory can, therefore, be read with a
single READ instruction.
The Read cycle is terminated by driving Chip Select (S) high. The rising edge of the Chip
Select (S) signal can occur at any time during the cycle.
The first byte addressed can be any byte within any page.
The instruction is not accepted, and is not executed, if a Write cycle is currently in progress.
Figure 11. Read from Memory Array (READ) sequence
S
0
1
2
3
4
5
6
7
8
9
10
20 21 22 23 24 25 26 27 28 29 30 31
C
Instruction
16-Bit Address
15 14 13
MSB
3
2
1
0
D
Q
Data Out 1
Data Out 2
High Impedance
2
7
6
5
4
3
1
7
0
MSB
AI01793D
22/39
M95512-W, M95512-R
Instructions
6.6
Write to Memory Array (WRITE)
As shown in Figure 12, to send this instruction to the device, Chip Select (S) is first driven
low. The bits of the instruction byte, address byte, and at least one data byte are then shifted
in, on Serial Data Input (D).
The instruction is terminated by driving Chip Select (S) high at a byte boundary of the input
data. The self-timed Write cycle triggered by the rising edge of Chip Select (S) continues for
a period t (as specified in Table 13 and Table 14), at the end of which the Write in Progress
W
(WIP) bit is reset to 0.
In the case of Figure 12, Chip Select (S) is driven high after the eighth bit of the data byte
has been latched in, indicating that the instruction is being used to write a single byte. If,
though, Chip Select (S) continues to be driven low, as shown in Figure 13., the next byte of
input data is shifted in, so that more than a single byte, starting from the given address
towards the end of the same page, can be written in a single internal write cycle.
Each time a new data byte is shifted in, the least significant bits of the internal address
counter are incremented. If the number of data bytes sent to the device exceeds the page
boundary, the internal address counter rolls over to the beginning of the page, and the
previous data there are overwritten with the incoming data. (The page size of these devices
is 128 bytes).
The instruction is not accepted, and is not executed, under the following conditions:
●
if the Write Enable Latch (WEL) bit has not been set to 1 (by executing a Write Enable
instruction just before)
●
●
if a Write cycle is already in progress
if the device has not been deselected, by Chip Select (S) being driven high, at a byte
boundary (after the eighth bit, b0, of the last data byte that has been latched in)
●
if the addressed page is in the region protected by the Block Protect (BP1 and BP0)
bits.
Figure 12. Byte Write (WRITE) sequence
S
0
1
2
3
4
5
6
7
8
9
10
20 21 22 23 24 25 26 27 28 29 30 31
C
Instruction
16-Bit Address
Data Byte
15 14 13
3
2
1
0
7
6
5
4
3
2
0
1
D
Q
High Impedance
AI01795D
23/39
Instructions
M95512-W, M95512-R
Figure 13. Page Write (WRITE) sequence
S
0
1
2
3
4
5
6
7
8
9
10
20 21 22 23 24 25 26 27 28 29 30 31
C
D
Instruction
16-Bit Address
Data Byte 1
15 14 13
3
2
1
0
7
6
5
4
3
2
0
1
S
C
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
Data Byte 2
Data Byte 3
Data Byte N
7
6
5
4
3
2
0
7
6
5
4
3
2
0
6
5
4
3
2
0
1
1
1
D
AI01796D
24/39
M95512-W, M95512-R
ECC (Error Correction Code) and Write cycling
7
ECC (Error Correction Code) and Write cycling
The M95512-W and M95512-R devices offer an ECC (Error Correction Code) logic which
compares each 4-byte word with its associated 6 EEPROM bits of ECC. As a result, if a
single bit out of 4 bytes of data happens to be erroneous during a Read operation, the ECC
detects it and replaces it by the correct value. The read reliability is therefore much improved
by the use of this feature.
Note however that even if a single byte has to be written, 4 bytes are internally modified
(plus the ECC bits), that is, the addressed byte is cycled together with the other three bytes
making up the word. It is therefore recommended to write by words of 4 bytes in order to
benefit from the larger amount of Write cycles.
The M95512-W and M95512-R devices are qualified at 1 million (1 000 000) Write cycles,
using a cycling routine that writes to the device by multiples of 4-byte packets.
8
Power-up and delivery state
8.1
Power-up state
After Power-up, the device is in the following state:
●
Standby Power mode
●
Deselected (after Power-up, a falling edge is required on Chip Select (S) before any
instructions can be started).
●
●
●
Not in the Hold Condition
Write Enable Latch (WEL) is reset to 0
Write In Progress (WIP) is reset to 0
The SRWD, BP1 and BP0 bits of the Status Register are unchanged from the previous
power-down (they are non-volatile bits).
8.2
Initial delivery state
The device is delivered with the memory array set at all 1s (FFh). The Status Register Write
Disable (SRWD) and Block Protect (BP1 and BP0) bits are initialized to 0.
25/39
Maximum rating
M95512-W, M95512-R
9
Maximum rating
Stressing the device outside the ratings listed in Table 6 may cause permanent damage to
the device. These are stress ratings only, and operation of the device at these, or any other
conditions outside those indicated in the Operating sections of this specification, is not
implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect
device reliability. Refer also to the STMicroelectronics SURE Program and other relevant
quality documents.
Table 6.
Symbol
Absolute maximum ratings
Parameter
Min.
Max.
Unit
TA
TSTG
TLEAD
VO
Ambient operating temperature
Storage temperature
Lead temperature during soldering
Output voltage
–40
–65
130
150
°C
°C
°C
V
See note (1)
–0.50
–0.50
–0.50
VCC+0.6
6.5
VI
Input voltage
V
VCC
Supply voltage
6.5
V
Electrostatic discharge voltage (Human Body
Model)(2)
VESD
–4000
4000
V
1. Compliant with JEDEC Std J-STD-020C (for small body, Sn-Pb or Pb assembly), the ST ECOPACK®
7191395 specification, and the European directive on Restrictions on Hazardous Substances (RoHS)
2002/95/EU
2. AEC-Q100-002 (compliant with JEDEC Std JESD22-A114A, C1=100pF, R1=1500Ω, R2=500Ω)
26/39
M95512-W, M95512-R
DC and AC parameters
10
DC and AC parameters
This section summarizes the operating and measurement conditions, and the DC and AC
characteristics of the device. The parameters in the DC and AC Characteristic tables that
follow are derived from tests performed under the Measurement Conditions summarized in
the relevant tables. Designers should check that the operating conditions in their circuit
match the measurement conditions when relying on the quoted parameters.
Table 7.
Symbol
Operating conditions (M95512-W)
Parameter
Min.
Max.
Unit
VCC
TA
Supply voltage
2.5
–40
–40
5.5
85
V
Ambient operating temperature (device grade 6)
Ambient operating temperature (device grade 3)
°C
°C
125
Table 8.
Symbol
Operating conditions (M95512-R)
Parameter
Min.
Max.
Unit
VCC
TA
Supply voltage
1.8
5.5
85
V
Ambient operating temperature
–40
°C
Table 9.
Symbol
AC measurement conditions
Parameter
Min.
Max.
Unit
CL
Load capacitance
30
pF
ns
V
Input Rise and Fall times
Input Pulse voltages
50
0.2VCC to 0.8VCC
0.3VCC to 0.7VCC
Input and output timing reference voltages
V
Figure 14. AC measurement I/O waveform
Input Levels
Input and Output
Timing Reference Levels
0.8V
CC
0.7V
CC
0.3V
CC
0.2V
CC
AI00825B
(1)
Table 10. Capacitance
Symbol
Parameter
Test condition
Min.
Max.
Unit
COUT
Output capacitance (Q)
Input capacitance (D)
VOUT = 0 V
VIN = 0 V
8
8
6
pF
pF
pF
CIN
Input capacitance (other pins)
VIN = 0 V
1. Not 100% tested.
27/39
DC and AC parameters
M95512-W, M95512-R
Table 11. DC characteristics (M95512-W)
Test condition specified in
Symbol
Parameter
Min.
Max.
Unit
Table 7
ILI
Input leakage current
Output leakage current
VIN = VSS or VCC
2
2
µA
µA
ILO
S = VCC, VOUT = VSS or VCC
C = 0.1VCC/0.9VCC at 5 MHz,
VCC = 2.5 V, Q = open
3
5
6
mA
mA
mA
µA
ICC
Supply current (Read)
Supply current (Write)
C = 0.1VCC/0.9VCC at 5 MHz,
VCC = 5 V, Q = open
During tW, S = VCC
,
(1)
ICC0
2.5 V < VCC < 5.5 V
Supply current
(Standby Power mode)
S = VCC, VIN = VSS or VCC
,
ICC1
5
2.5 V < VCC < 5.5 V
VIL
VIH
Input low voltage
Input high voltage
–0.45
0.3 VCC
V
V
0.7 VCC VCC+1
0.4
VCC = 2.5 V and IOL = 1.5 mA or
VCC = 5 V and IOL = 2 mA
VOL
VOH
Output low voltage
Output high voltage
V
V
VCC = 2.5 V and IOH = –0.4 mA or
VCC = 5 V and IOH = –2 mA
0.8 VCC
1. Characterized value, not tested in production.
Table 12. DC characteristics (M95128-R)
Test condition specified in
Symbol
Parameter
Min
Max
Unit
Table 8
ILI
Input leakage current
Output leakage current
VIN = VSS or VCC
2
2
µA
µA
ILO
S = VCC, VOUT = VSS or VCC
C = 0.1VCC/0.9VCC at 2 MHz,
VCC = 1.8 V, Q = open
ICC
Supply current (Read)
Supply current (Write)
1
3
3
mA
mA
µA
During tW, S = VCC
,
(1)
ICC0
1.8 V < VCC < 2.5 V
Supply current (Standby
Power mode)
S = VCC, VIN = VSS or VCC
,
ICC1
1.8 V < VCC < 2.5 V
VIL
VIH
Input low voltage
Input high voltage
Output low voltage
Output high voltage
–0.45
0.3 VCC
VCC+1
0.3
V
V
V
V
0.7 VCC
VOL
VOH
IOL = 0.15 mA, VCC = 1.8 V
IOH = –0.1 mA, VCC = 1.8 V
0.8 VCC
1. Characterized value, not tested in production.
28/39
M95512-W, M95512-R
DC and AC parameters
Table 13. AC characteristics (M95512-W)
Test conditions specified in Table 9 and Table 7
Symbol
Alt.
Parameter
Min.
Max.
Unit
fC
fSCK Clock frequency
D.C.
90
5
MHz
ns
ns
ns
ns
ns
ns
ns
µs
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
tSLCH
tSHCH
tSHSL
tCHSH
tCHSL
tCSS1 S active setup time
tCSS2 S not active setup time
tCS S deselect time
90
100
90
tCSH S active hold time
S not active hold time
tCLH Clock high time
tCLL Clock low time
90
(1)
tCH
90
(1)
tCL
90
(2)
tCLCH
tRC
tFC
Clock rise time
Clock fall time
1
1
(2)
tCHCL
tDVCH
tCHDX
tHHCH
tHLCH
tCLHL
tCLHH
tDSU Data in setup time
20
30
70
40
0
tDH
Data in hold time
Clock low hold time after HOLD not active
Clock low hold time after HOLD active
Clock low setup time before HOLD active
Clock low setup time before HOLD not active
0
(2)
tSHQZ
tDIS Output disable time
100
60
tCLQV
tV
Clock low to output valid
Output hold time
tCLQX
tHO
tRO
tFO
tLZ
0
(2)
tQLQH
Output rise time
50
50
50
100
5
(2)
tQHQL
Output fall time
tHHQV
HOLD high to output valid
HOLD low to output High-Z
(2)
tHLQZ
tHZ
tW
tWC Write time
1. tCH + tCL must never be less than the shortest possible clock period, 1 / fC(max)
2. Value guaranteed by characterization, not 100% tested in production.
29/39
DC and AC parameters
M95512-W, M95512-R
Table 14. AC characteristics (M95512-R)
Test conditions specified in Table 9 and Table 8
Symbol
Alt.
Parameter
Min.
D.C.
Max.
Unit
fC
fSCK
tCSS1
tCSS2
tCS
Clock frequency
2
MHz
ns
ns
ns
ns
ns
ns
ns
µs
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
tSLCH
tSHCH
tSHSL
tCHSH
tCHSL
S active setup time
200
200
200
200
200
200
200
S not active setup time
S deselect time
tCSH
S active hold time
S not active hold time
Clock high time
(1)
tCH
tCLH
tCLL
tRC
(1)
tCL
Clock low time
(2)
tCLCH
Clock rise time
1
1
(2)
tCHCL
tFC
Clock fall time
tDVCH
tCHDX
tHHCH
tHLCH
tCLHL
tCLHH
tDSU
tDH
Data in setup time
40
50
140
90
0
Data in hold time
Clock low hold time after HOLD not active
Clock low hold time after HOLD active
Clock low setup time before HOLD active
Clock low setup time before HOLD not active
Output disable time
0
(2)
tSHQZ
tDIS
tV
250
150
tCLQV
Clock low to output valid
Output hold time
tCLQX
tHO
tRO
tFO
tLZ
0
(2)
tQLQH
Output rise time
100
100
100
250
5
(2)
tQHQL
Output fall time
tHHQV
HOLD high to output valid
HOLD low to output High-Z
Write time
(2)
tHLQZ
tHZ
tWC
tW
1. tCH + tCL must never be less than the shortest possible clock period, 1 / fC(max)
2. Value guaranteed by characterization, not 100% tested in production.
30/39
M95512-W, M95512-R
Figure 15. Serial input timing
DC and AC parameters
tSHSL
tSHCH
S
C
tCHSL
tSLCH
tCH
tCHSH
tDVCH
tCHCL
tCHDX
tCL
tCLCH
MSB IN
LSB IN
D
Q
High impedance
AI01447d
Figure 16. Hold timing
S
tHLCH
tCLHL
tHHCH
C
tCLHH
tHHQV
tHLQZ
Q
HOLD
AI01448c
31/39
DC and AC parameters
M95512-W, M95512-R
Figure 17. Serial output timing
S
tCH
tSHSL
C
tCLQV
tCLQX
tCLCH
tCHCL
tCL
tSHQZ
Q
D
tQLQH
tQHQL
ADDR
LSB IN
AI01449f
32/39
M95512-W, M95512-R
Package mechanical data
11
Package mechanical data
®
In order to meet environmental requirements, ST offers the M95512-W in ECOPACK
packages. These packages have a lead-free second level interconnect. The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at www.st.com.
Figure 18. SO8N – 8 lead plastic small outline, 150 mils body width, package outline
h x 45˚
A2
A
c
ccc
b
e
0.25 mm
D
GAUGE PLANE
k
8
1
E1
E
L
A1
L1
SO-A
1. Drawing is not to scale.
Table 15. SO8N – 8 lead plastic small outline, 150 mils body width, package
mechanical data
millimeters
inches(1)
Symbol
Typ
Min
Max
Typ
Min
Max
A
A1
A2
b
1.75
0.25
0.0689
0.0098
0.10
1.25
0.28
0.17
0.0039
0.0492
0.011
0.48
0.23
0.10
5.00
6.20
4.00
–
0.0189
0.0091
0.0039
0.1969
0.2441
0.1575
-
c
0.0067
ccc
D
4.90
6.00
3.90
1.27
4.80
5.80
3.80
–
0.1929
0.2362
0.1535
0.05
0.189
0.2283
0.1496
-
E
E1
e
h
0.25
0°
0.50
8°
0.0098
0°
0.0197
8°
k
L
0.40
1.27
0.0157
0.05
L1
1.04
0.0409
1. Values in inches are converted from mm and rounded to 4 decimal digits.
33/39
Package mechanical data
M95512-W, M95512-R
Figure 19. TSSOP8 – 8 lead thin shrink small outline, package outline
D
8
5
c
E1
E
1
4
α
A1
L
A
A2
L1
CP
b
e
TSSOP8AM
1. Drawing is not to scale.
Table 16. TSSOP8 – 8 lead thin shrink small outline, package mechanical data
millimeters
Min
inches(1)
Symbol
Typ
Max
Typ
Min
Max
A
A1
A2
b
1.200
0.150
1.050
0.300
0.200
0.100
3.100
–
0.0472
0.0059
0.0413
0.0118
0.0079
0.0039
0.1220
–
0.050
0.800
0.190
0.090
0.0020
0.0315
0.0075
0.0035
1.000
0.0394
c
CP
D
3.000
0.650
6.400
4.400
0.600
1.000
2.900
–
0.1181
0.0256
0.2520
0.1732
0.0236
0.0394
0.1142
–
e
E
6.200
4.300
0.450
6.600
4.500
0.750
0.2441
0.1693
0.0177
0.2598
0.1772
0.0295
E1
L
L1
α
0°
8
8°
0°
8
8°
N
1. Values in inches are converted from mm and rounded to 4 decimal digits.
34/39
M95512-W, M95512-R
Part numbering
12
Part numbering
Table 17. Ordering information scheme
Example:
M95512
–
W MN
6
T
P /AB
Device type
M95 = SPI serial access EEPROM
Device function
512 = 512 Kbit (65536 × 8)
Operating voltage
W = VCC = 2.5 V to 5.5 V
R = VCC = 1.8 V to 5.5 V
Package
MN = SO8 (150 mil width)
DW = TSSOP8 (169 mil width)
Device grade
6 = Industrial temperature range, –40 to 85 °C.
Device tested with standard test flow
3 = Device tested with high reliability certified flow(1)
Automotive temperature range (–40 to 125 °C)
.
Option
blank = Standard packing
T = Tape and reel packing
Plating technology
P or G = ECOPACK® (RoHS compliant)
Process
/AB = F8L(2)
1. ST strongly recommends the use of the Automotive Grade devices for use in an automotive environment.
The high reliability certified flow (HRCF) is described in the quality note QNEE9801. Please ask your
nearest ST sales office for a copy.
2. The process letter only concerns device grade 3 devices.
35/39
Part numbering
M95512-W, M95512-R
For a list of available options (speed, package, etc.) or for further information on any aspect
of this device, please contact your nearest ST sales office.
Table 18. Available M95512x products (package, voltage range, temperature grade)
M95512-W
2.5 V to 5.5 V
M95512-R
1.8 V to 5.5 V
Package
Range 6
Range 3
SO8 (MN)
TSSOP (DW)
Range 6
Range 6
Range 6
36/39
M95512-W, M95512-R
Revision history
13
Revision history
Table 19. Document revision history
Date
Revision
Changes
Jan-1999
1.0
Document written
Document reformatted using the new template
Voltage range -S added, and -R removed
Instruction Sequence illustrations updated
13-Feb-2002
2.0
Announcement made of planned upgrade to 10 MHz clock for the 5V, –40
to 85°C, range
05-Dec-
2003
Table of contents, and Pb-free options added. VIL(min) improved to -0.45V.
Voltage range -R added, and -S removed
3.0
4.0
Old versions of document completely replaced by one rewritten from
M95256
02-Apr-2004
AC and DC characteristics tables updated with the performance data of the
new device identified with the process letter “A”.
Table 1., Product List added. AEC-Q100-002 compliance. Device Grade
information clarified. tHHQX, tCHHL and tCHHH corrected to tHHQV, tCLHL and
tCLHH, respectively.
03-Jan-2005
5.0
6.0
M95512 part number with 4.5V to 5.5V operating voltage range removed
(related tables removed). Document status changed to Preliminary Data.
Updated Figure 3: Bus master and memory devices on the SPI bus and
Figure 16: Hold timing. Power On Reset information clarified. Protected
Array Addresses modified in Table 2: Write-Protected block size. Ambient
Operating Temperature value added in Table 6: Absolute maximum ratings.
Supply Current (ICC) value modified for 10 MHz in Table 11: DC
characteristics (M95512-W). All values modified in Table 14: AC
characteristics (M95512-R). Document status changed to Datasheet.
30-Jun-2005
Document reformatted. Packages are ECOPACK® compliant.
10 MHz frequency removed. VCC supply voltage and VSS ground
descriptions added. Figure 3: Bus master and memory devices on the SPI
bus modified and explanatory paragraph added. Power-up and Power On
Reset paragraphs replaced by Section 4.1: Supply voltage (VCC).
Section 7: ECC (Error Correction Code) and Write cycling added.
TA max modified in Table 7: Operating conditions (M95512-W).
Note modified below Table 10: Capacitance.
CL modified in and Table 9: AC measurement conditions.
VIL max and ICC0 test conditions modified in Table 12: DC characteristics
(M95128-R).
06-Feb-2007
7
ICC modified in Table 11: DC characteristics (M95512-W), ICC0 added to
Table 11 and Table 12: DC characteristics (M95128-R) modified.
Table 14: AC characteristics (M95512-R) modified.
tSHQZ end timing line moved back in Figure 17: Serial output timing.
SO8N package specifications updated (see Figure 18 and Table 15).
Blank removed below Plating technology in Table 17: Ordering information
scheme.
The device endurance is specified at more than 1 000 000 (1 million)
cycles (corrected on page 1).
05-Jun-2007
8
37/39
Revision history
Table 19. Document revision history
M95512-W, M95512-R
Date
Revision
Changes
M95512-W is now available in the device grade 3 (automotive temperature
range), see Table 7 on page 27).
Section 4.1: Supply voltage (VCC) on page 12 updated.
Section 6.4: Write Status Register (WRSR) on page 20 and Section 6.6:
Write to Memory Array (WRITE) on page 23 clarified.
ICC0 modified in Table 11: DC characteristics (M95512-W).
03-Jul-2008
9
Figure 15: Serial input timing, Figure 16: Hold timing and Figure 17: Serial
output timing updated.
Package mechanical data values in inches are calculated from the
millimeter values and rounded to four decimal digits (see Section 11:
Package mechanical data).
Table 18: Available M95512x products (package, voltage range,
temperature grade) added.. Small text changes.
38/39
M95512-W, M95512-R
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2008 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
39/39
相关型号:
©2020 ICPDF网 联系我们和版权申明