GS-R24F0002.0 [STMICROELECTRONICS]
2A DC/DC converter modules; 图2A的DC / DC转换器模块
| 型号： | GS-R24F0002.0 |
| 厂家： | 
ST |
| 描述： | 2A DC/DC converter modules |
| 文件： | 总12页 (文件大小：204K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
GS-R24F
2A DC/DC converter modules
Features
■ MTBF 1 000 000 hours (TA = 25
■ 2A max output current
■ 35V max input voltage
■ 1.5V max drop-out voltage
■ Remote logic inhibit/enable
■ Synchronization
°
C)
■ Not-latching overload and short circuit
protection
■ Thermal shutdown
■ Fixed or adjustable output
■ No heatsink required
■ Operating temperature range -25°C ÷ 85°C
Description
The GS-R24F series is a family of high efficiency
step down switching voltage regulator, designed
to replace linear regulators.
Based on ST L5973 device, these non isolated
regulators are suitable for various applications,
including telecom, industry, computer and
distributed power supply system having a wide
range input voltage.
Order codes
Output Voltage Input Voltage Output Ripple Efficiency
Part number
Notes
[V]
[V]
[mVpp]
[%]
GS-R24F0182.0
GS-R24F0252.0
GS-R24F0332.0
GS-R24F0502.0
GS-R24F0002.0
GS-R24F1201.5
GS-R24F0001.0
1.8 ± 4%
2.5 ± 4%
3.3 ± 4%
5.0 ± 4%
1.235 ÷ 5.5
12 ± 4%
16 ÷ 35
16 ÷ 35
16 ÷ 35
16 ÷ 35
16 ÷ 35
16 ÷ 35
16 ÷ 35
25
25
72
76
Fixed output voltage
Fixed output voltage
Fixed output voltage
Fixed output voltage
Progr. output voltage
Fixed output voltage
Progr. output voltage
25
82
25
85
25
68 ÷ 85
91
100
3.3 ÷ 24
100 ÷ 250
78 ÷ 96
October 2006
Rev 1
1/12
www.st.com
12
Contents
GS-R24F
Contents
1
Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1
1.2
Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1
2.2
2.3
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Thermal de-rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
4
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.1
4.2
4.3
4.4
4.5
4.6
4.7
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Reference voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Inhibit function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Multiple units synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Current limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Thermal shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Output voltage programming
(GS-R24F0002.0 and GS-R24F0001.0) 7
4.8
Loop compensation (GS-R24F0002.0 and GS-R24F0001.0) . . . . . . . . . . 7
5
Additional features and protections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.1
Output overvoltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6
7
Ordering scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2/12
GS-R24F
Pin settings
1
Pin settings
1.1
Pin connection
Figure 1. Pin connection and mechanical data (dimensions in mm)
1.2
Pin description
Table 1.
Name
Pin description
Function
Description
A logic high level disables the device. When the pin is open, an
internal pull up disables the device
1
INH
2
3
Vref
Input +
3.3V reference voltage
DC input voltage
4
Input +
DC input voltage
5
Input GND
Input GND
Output GND
Output GND
Vout
Return for input voltage source
Return for input voltage source
Return for output voltage source
Return for output voltage source
Regulated power output
Regulated power output
6
7
8
9
10
Vout
Feedback input, available on adjustable device and on request for
additional compensation
11
12
FB
Sync
Master/Slave synchronization
3/12
Maximum ratings
GS-R24F
2
Maximum ratings
2.1
Absolute maximum ratings
Table 2.
Symbol
Absolute maximum ratings
Parameter
Value
Unit
VI
IOUT
V1
DC input voltage
36
internally limit
-0.3 to VI
-0.3 to 4
4
V
Maximum output current
INH
Sync
FB
V
V
V
V12
V11
2.2
2.3
Thermal data
Table 3.
Symbol
Absolute maximum ratings
Parameter
Storage temperature range
Operating ambient temperature
Value
Unit
Tstg
Top
-40 ÷ 105
-25 ÷ 85
°C
°C
Thermal de-rating
Table 4.
Symbol
Thermal de-rating for free air condition (all versions)
Parameter
Test condition
Value
Unit
VI = 16 ÷ 35V --------TA = 60°C
VI = 16 ÷ 35V---------TA = 65°C
VI = 16 ÷ 35V ---------TA = 70°C
VI = 16 ÷ 35V ---------TA = 75°C
VI = 16 ÷ 35V ---------TA = 80°C
VI = 16 ÷ 35V ------ --TA = 85°C
1.95
1.85
1.75
1.65
1.55
1.40
Io
Output current
A
4/12
GS-R24F
Electrical characteristics
3
Electrical characteristics
T = 25°C, unless otherwise specified
A
Table 5.
Symbol
Electrical characteristics (all version)
Parameter Test condition
VI =24V Io = 2A
Min
Typ
Max
Unit
Vr
Vr
Vr
Ripple voltage
25
35
mVpp
for GS-R24Fyyy2.0
VI =24V Io = 1.5A
for GS-R24F1201.5
Ripple voltage
100
250
mVpp
VI =24V Io = 1A
for GS-R24F0001.0
Ripple voltage
100
mVpp
mV/°C
A
Temperature stability
Output current
VI =Vo + 1.5V Io = 2A
VI =16 ÷ 35V
for GS-R24Fyyy2.0
Io
Io
Io
0
0
0
2
1.5
1
VI =16 ÷ 35V
for GS-R24F1201.5
Output current
Output current
A
A
VI =16 ÷ 35V
for GS-R24F0001.0
IoL
Iq
Current limit
VI =16 ÷ 35V
2.5
1.8
A
Quiescent current
VI =24V Io = 0A
2.5
mA
Total stand-by quiescent
current
Iqst-by
fs
V
inh>2.2V Vi = 35V
80
150
µA
Switching frequency
Reference voltage
Short circuit current
VI = 24V Io = 2A
225
250
275
3.366
30
kHz
V
VI = 16 ÷ 35V Iref = 0 ÷ 5mA
3.234 3.3
Vref
INH
8
10
mA
V
Device ON
0.8
INH threshold voltage
Device OFF
2.2
V
VFB
SRV
Rth
Feedback voltage
Vi=16 ÷ 35V IO=0 ÷ 2A
1.22 1.235 1.25
V
Supply voltage rejection
Thermal resistance
mV/V
°C/W
Case to ambient
5/12
Application information
GS-R24F
4
Application information
4.1
Input voltage
The recommended maximum operating DC Input Voltage is 35V including ripple voltage.
4.2
4.3
Reference voltage
No capacitor is required for stability.
Inhibit function
The inhibit feature allows to put the device in stand-by mode.
With INH pin 1 is higher than 2.2V the device is disabled and the current consumption is
reduced to less than 150µA for V = 35V.
I
With INH pin lower than 0.8V, the device is enabled.
If the INH pin is left floating, an internal pull up ensures that the voltage at the pin reaches
the inhibit threshold and the device is disabled.
The pin can be pulled to VI to disable the device.
4.4
4.5
Multiple units synchronization
Using more than one unit on the same circuit, it is possible to synchronize the switching
frequency, connecting all pin 12 together (see Figure 4).
The unit with higher frequency becomes the master.
Current limitation
The device has two current limit protections, pulse by pulse and frequency fold back.
The current is sensed through a resistor and if it reaches the threshold, the on time is
reduced and consequently the output voltage, too.
Since the minimum switch ON time (necessary to avoid false overcurrent signal) is not
enough to obtain a sufficiently low duty cycle at 250Hz, the output current could increase
again, in strong overcurrent or short circuit conditions.
For this reason the switching frequency is also reduced to keep the inductor current within
its maximum threshold limit.
The frequency depends on the feedback voltage.
As the feedback voltage decreases (due to the reduced duty cycle), the switching frequency
decrease too.
6/12
GS-R24F
Application information
4.6
Thermal shutdown
The shutdown block generates a signal that turns off the power stage if the temperature of
the internal chip goes higher than a fixed internal threshold (150° C min).
The sensing element of the chip is very close to the PDMOS area, so ensuring an accurate
and fast temperature detection.
An hysteresis of approximately 20° C avoids that the devices turns on and off continuously.
4.7
Output voltage programming
(GS-R24F0002.0 and GS-R24F0001.0)
The GS-R24F0002.0 output voltage is 5.54V 4ꢀ, the GS-R24F0001.0 output voltage is
24.44V 4ꢀ, to reduce these values connect a resistor between pin 11 (FB) and pin 10
(V ).
out
The resistor must be located very close to the proper pins, to minimize the injected noise
(see figure 2).
The resistor value is calculated using the following formula:
for GS-R24F0002.0 Rv = [(V - 1.235) * 11.3] / (5.54 - V ) --[kΩ];
out
out
for GS-R24F0001.0 Rv = [(V - 1.235) * 62] / (24.44 - V ) --[kΩ].
out
out
V
can be adjusted between 1.235V (Rv = 0Ω) and 5.54V/24.44V (Rv = open).
out
4.8
Loop compensation (GS-R24F0002.0 and GS-R24F0001.0)
If required by particular load conditions, it is possible to change the feedback loop
compensation, adding an external capacitor between pin 11 (FB) and pin 10 (V ), which
out
will act as speed up (see Figure 3).
7/12
Additional features and protections
GS-R24F
5
Additional features and protections
5.1
Output overvoltage protection
The overvoltage protection, OVP, is realized by using an internal comparator, whose input is
connected to the feedback. It turns off the power stage when the OVP threshold is reached.
This threshold is typically 30ꢀ higher than the feedback voltage.
Figure 2. Output voltage programming Figure 3. Loop compensation
Figure 4. Multiple units synchronization
8/12
GS-R24F
Additional features and protections
Figure 5. P.C.B. Footprint (dimensions in mm)
9/12
Ordering scheme
GS-R24F
6
Ordering scheme
Table 6.
Ordering information scheme
GS-
R24
F018
2.0
Input Voltage
24 = 24V
Output Voltage
018 = 1.8V
025 = 2.5V
033 = 3.3V
050 = 5.0V
120 = 12V
000 = 1.235 ÷ 5.5V / 3.3 ÷ 24V
Output Current
2.0 = 2A
1.5 = 1.5A
1.0 = 1A
10/12
GS-R24F
Revision history
7
Revision history
Table 7.
Date
13-Oct-2006
Revision history
Revision
Changes
1
Initial release
11/12
GS-R24F
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2006 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
12/12
相关型号：
©2020 ICPDF网 联系我们和版权申明