SP-03-LR1-CDFM [SOURCE]
1310nm FP laser and PIN photodetector for 40km transmission;
| 型号： | SP-03-LR1-CDFM |
| 厂家： | 
SOURCE PHOTONICS, INC. |
| 描述： | 1310nm FP laser and PIN photodetector for 40km transmission |
| 文件： | 总10页 (文件大小：277K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SP-03-LR1/LR2-xDFM
Features
z
z
Date rate 155Mbps
1310nm FP laser and PIN photodetector for
40km transmission
z
z
1550nm uncooled DFB laser and PIN
photodetector for 80km transmission
Digital diagnostic monitor interface compliant with
SFF-8472
z
z
z
z
SFP MSA package with duplex LC connector
+3.3V single power supply
Power consumption less than 1W
Operating case temperature
Standard temp:-5~+70°C
Industrial temp:-40~+85°C
z
RoHS compliant
Regulatory Compliance
Table 1 - Regulatory Compliance
Feature
Standard
Performance
Electrostatic Discharge
(ESD) to the Electrical Pins
Electrostatic Discharge (ESD) to the
Duplex LC Receptacle
Electromagnetic
MIL-STD-883E
Class 1
Method 3015.7
IEC 61000-4-2
Compliant with standard
Compliant with standard
FCC Part 15 Class B
Interference (EMI)
FDA 21CFR
1040.11
1040.10
and
Laser Eye Safety
RoHS
Compliant with Class I laser product.
Compliant with RoHS
EN (IEC) 60825-1,2
2011/65/EU
Absolute Maximum Ratings
Table 2 - Absolute Maximum Ratings
Parameter
Symbol
Min.
Typical
Max.
Unit
Notes
Storage Temperature
Supply Voltage
TS
VCC
RH
-40
-0.5
+5
-
-
-
+85
+3.6
+95
°C
V
Operating Relative Humidity
%
DS-5585 Rev 04 2013-12-20
SP-03-LR1/LR2-xDFM
Recommended Operating Conditions
Table 3 – Recommended Operating Conditions
Parameter
Symbol
Min.
Typical
Max.
Unit
Notes
Standard
Industrial
-5
-40
3.13
-
-
-
+70
+85
3.47
300
1
°C
°C
Operating Case
Temperature
TC
Power Supply Voltage
Power Supply Current
Power Dissipation
Data Rate
VCC
ICC
PD
3.3
-
V
mA
W
-
-
155
Mbps
Table 4 – Optical Characteristics
SP-03-LR1-CDFM SP-03-LR1-IDFM (1310nm FP and PIN, 40km, Monitoring function)
Transmitter
Parameter
Centre Wavelength
Symbol
Min.
Typical
Max.
Unit
Notes
λC
P0UT
∆λ
1263
-5
1360
nm
dBm
nm
dB
Average Output Power
Spectral Width (RMS)
Extinction Ratio
0
3
1
EX
10
0.01
0.1
UI
Jitter Generation (RMS)
Jitter Generation (pk-pk)
Optical Eye Mask
UI
Compliant with Telcordia GR-253-CORE and ITU-T G.957
2
Receiver
Centre Wavelength
Receiver Sensitivity
Receiver Overload
Optical Path Penalty
LOS Assert
λC
1260
-10
1580
-34
nm
dBm
dBm
dB
PIN
PIN
3
3
4
1
LOSA
LOSD
-45
dBm
dBm
dB
LOS Deassert
-37
4
LOS Hysteresis
Notes:
0.5
1. The optical power is launched into SMF.
2. Measured with a PRBS 223-1 test pattern @155Mbps.
3. Measured with a PRBS 223-1 test pattern @155Mbps, BER ≤1×10-10.
4. Measured with a PRBS 223-1 test pattern @155Mbps, over 40km G.652 SMF, BER ≤1×10-10.
DS-5585 Rev 04 2013-12-20
SP-03-LR1/LR2-xDFM
Table 5– Optical Characteristics
SP-03-LR2-CDFM SP-03-LR2-IDFM (1550nm DFB and PIN, 80km, Monitoring function)
Transmitter
Parameter
Centre Wavelength
Symbol
Min.
Typical
Max.
Unit
Notes
λC
P0UT
∆λ
1480
-5
1580
nm
dBm
nm
dB
Average Output Power
Spectral Width (-20dB)
Side Mode Suppression Ratio
Extinction Ratio
0
1
1
SMSR
EX
30
10
dB
0.01
0.1
UI
Jitter Generation (RMS)
Jitter Generation (pk-pk)
Optical Eye Mask
UI
Compatible with Telcordia GR-253-CORE and ITU-T G.957
2
Receiver
Centre Wavelength
Receiver Sensitivity
Receiver Overload
Optical Path Penalty
LOS Assert
λC
1260
1580
-34
nm
dBm
dBm
dB
PIN
PIN
3
3
4
-10
1
LOSA
LOSD
-45
dBm
dBm
dB
LOS Deassert
-37
4
LOS Hysteresis
Notes:
0.5
1. The optical power is launched into SMF.
2. Measured with a PRBS 223-1 test pattern @155Mbps.
3. Measured with a PRBS 223-1 test pattern @155Mbps, BER ≤1×10-10.
4. Measured with a PRBS 223-1 test pattern @155Mbps, over 80km G.652 SMF, BER ≤1×10-10.
Electrical Characteristics
Table 6– Electrical Characteristics
Transmitter
Parameter
Symbol
Min.
Typical
Max.
Unit
Notes
Data Input Swing Differential
Input Differential Impedance
Tx_DIS Disable
VIN
ZIN
VD
500
90
2400
110
mV
Ω
V
1
100
2.0
GND
2.0
0
VCC
Tx_DIS Enable
VEN
GND+0.8
Vcc+0.3
0.8
V
TX_ Fault (Fault)
V
TX_ Fault (Normal)
V
DS-5585 Rev 04 2013-12-20
SP-03-LR1/LR2-xDFM
Receiver
370
DataOutput Swing Differential
Rx_LOS Fault
VOUT
2000
mV
V
1
VLOS-Fault
VLOS-Normal
2.0
Vcc+0.3
GND+0.8
Rx_LOS Normal
GND
V
Notes:
1. Internally AC coupled
Recommended Host Board Power Supply Circuit
Figure 1, Recommended Host Board Power Supply Circuit
Recommended Interface Circuit
Host Board
Vcc (+3.3V)
SFP Module
VccT
10K
2×4.7K to 10K
TX Disable
TX Fault
TD +
Z=50
SerDat Out +
SerDat Out -
Laser
driver
Z=50
Z=50
TD -
RD +
RD -
Protocol
IC
SERDES
IC
SerDat In +
SerDat In -
Amplifier
Z=50
LOS
Vcc (+3.3V)
3×4.7K to 10K
MOD-DEF2
MOD-DEF1
MOD-DEF0
EEPROM
RGND
Figure 2, Recommended Interface Circuit
DS-5585 Rev 04 2013-12-20
SP-03-LR1/LR2-xDFM
Pin Definitions
Figure 3 below shows the pin numbering of SFP electrical interface. The pin functions are described in Table
7 with some accompanying notes.
P in 20
TO P V IE W
O F B O A R D
P in 11
P in 10
B O T TO M V IE W
O F B O A R D
P in
1
Figure 3, Pin View
Table7 - Pin Function Definitions
Pin No.
1
Name
VeeT
Function
Plug Seq.
Notes
Transmitter Ground
Transmitter Fault Indication
Transmitter Disable
Module Definition 2
Module Definition 1
Module Definition 0
Not Connected
1
3
3
3
3
3
3
3
1
1
1
3
3
1
2
2
1
3
3
1
2
TX Fault
TX Disable
MOD-DEF2
MOD-DEF1
MOD-DEF0
Rate Select
LOS
Note 1
Note 2
Note 3
Note 3
Note 3
3
4
5
6
7
8
Loss of Signal
Note 4
9
VeeR
Receiver Ground
Receiver Ground
Receiver Ground
Inv. Received Data Out
Received Data Out
Receiver Ground
Receiver Power
10
11
12
13
14
15
16
17
18
19
20
VeeR
VeeR
RD-
Note 5
Note 5
RD+
VeeR
VccR
VccT
Transmitter Power
Transmitter Ground
Transmit Data In
VeeT
TD+
Note 6
Note 6
TD-
Inv. Transmit Data In
Transmitter Ground
VeeT
Notes:
DS-5585 Rev 04 2013-12-20
SP-03-LR1/LR2-xDFM
1. TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to
a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates a laser fault of
some kind. In the low state, the output will be pulled to less than 0.8V.
2. TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module
with a 4.7k~10kΩ resistor. Its states are:
Low (0~0.8V):
(>0.8V, <2.0V):
High (2.0~3.465V):
Open:
Transmitter on
Undefined
Transmitter Disabled
Transmitter Disabled
3. MOD-DEF 0,1,2 are the module definition pins. They should be pulled up with a 4.7k~10kΩ resistor on the host
board. The pull-up voltage shall be VccT or VccR.
MOD-DEF 0 is grounded by the module to indicate that the module is present
MOD-DEF 1 is the clock line of two wires serial interface for serial ID
MOD-DEF 2 is the data line of two wires serial interface for serial ID
4. LOS is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a
voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. In the
low state, the output will be pulled to less than 0.8V.
5. These are the differential receiver output. They are internally AC-coupled 100Ω differential lines which should
be terminated with 100Ω (differential) at the user SERDES.
6. These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential
termination inside the module.
EEPROM Information
The SFP MSA defines a 256-byte memory map in EEPROM describing the transceiver’s capabilities, standard
interfaces, manufacturer, and other information, which is accessible over a 2 wire serial interface at the 8-bit
address 1010000X (A0h). The memory contents refer to Table 9.
Table 8 - EEPROM Serial ID Memory Contents (A0h)
Field
Addr.
Size Name of Field
(Bytes)
Hex
Description
0
1
1
1
1
8
1
1
1
Identifier
03
SFP
Ext. Identifier 04
Connector 07
MOD4
2
LC
3—10
11
Transceiver 00 xx xx 00 00 00 00 00
Encoding 03
BR, nominal 02
OC 3, Single mode inter. or long reach
NRZ
12
155Mbps
13
Reserved
Length
00
28/50
14
15
1
1
(9um)-km
40km/80km
40km/80km
Length (9um) FF/FF
DS-5585 Rev 04 2013-12-20
SP-03-LR1/LR2-xDFM
16
17
18
19
1
1
1
1
Length (50um) 00
Length (62.5um)00
Length (copper) 00
Reserved
Vendor name
Reserved
00
53 4F 55 52 43 45 50 48
4F 54 4F 4E 49 43 53 20
00
20—35
16
“SOURCEPHOTONICS”(ASCⅡ)
“SP03xxxxDFM” (ASCⅡ)
36
1
3
37—39
Vendor OUI 00 1F 22
53 50 30 33 xx xx xx xx
44 46 4D 20 20 20 20 20
40—55
16
Vendor PN
56—59
60-61
62
4
2
1
1
2
1
1
Vendor rev 31 30 20 20
Wavelength 05 1E/06 0E
ASCⅡ( “31 30 20 20” means 1.0 revision)
1310nm/1550nm
Reserved
CC BASE
Options
00
Check sum of bytes 0 - 62
63
xx
64—65
66
00 1A
LOS, TX_FAULT and TX_DISABLE
BR, max
BR, min
00
67
00
xx xx xx xx xx xx xx xx
xx xx xx xx xx xx xx xx
68—83
16
Vendor SN
ASCⅡ.
Vendor date
code
Year (2 bytes), Month (2 bytes), Day (2
bytes)
84—91
92
8
1
xx xx xx xx xx xx 20 20
Diagnostic type 58
Diagnostics(Ext.Cal)
Diagnostics (Optional Alarm/warning flags,
Soft TX_FAULT and Soft TX_LOS
monitoring)
Enhanced
B0
93
1
option
94
95
1
1
SFF-8472
CC EXT
02
xx
Diagnostics(SFF-8472 Rev 9.4)
Check sum of bytes 64 - 94
96—255
160 Vendor specific
Note: The “xx” byte should be filled in according to practical case. For more information, please refer to the
related document of SFF-8472 Rev 9.5.
Monitoring Specification
The digital diagnostic monitoring interface also defines another 256-byte memory map in EEPROM, which
makes use of the 8 bit address 1010001X (A2h). Please see Figure 4. For detail EEPROM information,
please refer to the related document of SFF-8472 Rev 9.5. The monitoring specification of this product is
described in Table 9.
DS-5585 Rev 04 2013-12-20
SP-03-LR1/LR2-xDFM
Figure 4, EEPROM Memory Map Specific Data Field Descriptions
Table 9- Monitoring Specification
Parameter
Range
Accuracy
±3°C
Calibration
External
External
External
External
Standard
Industrial
-10 to 80°C
-40 to 95°C
3.0 to 3.6V
0 to 100mA
Temperature
±3°C
Voltage
Bias Current
SP-03-LR1-CDFM
±3%
±10%
-6 to +1 dBm
-6 to +1 dBm
-34 to –9 dBm
-34 to –9 dBm
±3dB
±3dB
±3dB
±3dB
External
External
External
External
SP-03-LR1-IDFM
SP-03-LR2-CDFM
SP-03-LR2-IDFM
SP-03-LR1-CDFM
SP-03-LR1-IDFM
SP-03-LR2-CDFM
SP-03-LR2-IDFM
TX Power
RX Power
DS-5585 Rev 04 2013-12-20
SP-03-LR1/LR2-xDFM
Mechanical Diagram
Figure 5, Mechanical Design Diagram of the SFP
Order Information
Table 10– Order Information
Part No.
Application
Temperature
Data Rate
Laser Source Fiber Type
SDH STM-1, L-1.1
SONET OC-3 LR1
SDH STM-1, L-1.1
SONET OC-3 LR1
SDH STM-1, L-1.2
SONET OC-3 LR2
SDH STM-1, L-1.2
SONET OC-3 LR2
SP-03-LR1-CDFM
SP-03-LR1-IDFM
SP-03-LR2-CDFM
SP-03-LR2-IDFM
-5~+70°C
155Mbps
1310nm FP
1310nm FP
1550nm DFB
1550nm DFB
SMF
SMF
SMF
SMF
-40~+85°C
-5~+70°C
-40~+85°C
155Mbps
155Mbps
155Mbps
Warnings
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static
free environment is highly recommended. Follow guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct
or indirect radiation.
DS-5585 Rev 04 2013-12-20
SP-03-LR1/LR2-xDFM
Legal Notice
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at Source Photonics’s sole and
absolute discretion. Source Photonics warrants performance of its products to current specifications only in
accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary”
are given to describe components only, and Source Photonics expressly disclaims any and all warranties for said
products, including express, implied, and statutory warranties, warranties of merchantability, fi tness for a particular
purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale
for further warranty information.
Source Photonics assumes no liability for applications assistance, customer product design, software performance,
or infringement of patents, services, or intellectual property described herein. No license, either express or implied,
is granted under any patent right, copyright, or intellectual property right, and Source Photonics makes no
representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual
property rights. Products described in this document are NOT intended for use in implantation or other life support
applications where malfunction may result in injury or death to persons. Source Photonics customers using or
selling products for use in such applications do so at their own risk and agree to fully defend and indemnify Source
Photonics for any damages resulting from such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees
that Source Photonics is not liable for any actual, consequential, exemplary, or other damages arising directly or
indirectly from any use of the information contained in this document. Customer must contact Source Photonics to
obtain the latest version of this publication to verify, before placing any order, that the information contained herein
is current.
Contact
U.S.A. Headquarters
20550 Nordhoff Street
Chatsworth, CA 91311
USA
China
Taiwan
Building #2&5, West Export Processing Zone
No. 8 Kexin Road, Hi-Tech Zone
Chengdu, 611731, China
Tel: +86-28-8795-8788
9F, No 81, Shui Lee Rd.
Hsinchu, Taiwan, R.O.C.
Tel: +886-3-5169222
Fax: +886-3-5169213
Tel: +1-818-773-9044
Fax: +1-818-773-0261
Fax: +86-28-8795-8789
© Copyright Source Photonics, Inc. 2007~2013
All rights reserved
DS-5585 Rev 04 2013-12-20
相关型号：
©2020 ICPDF网 联系我们和版权申明