USB2504-ABZJ [SMSC]
INTEGRATED USB2.0 COMPATIBLE 4 - PORT HUB; 集成USB2.0兼容4 - PORT HUB型号: | USB2504-ABZJ |
厂家: | SMSC CORPORATION |
描述: | INTEGRATED USB2.0 COMPATIBLE 4 - PORT HUB |
文件: | 总6页 (文件大小:430K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
USB2504/USB2504A
Integrated USB2.0
Compatible 4-Port Hub
Data Brief
PRODUCT FEATURES
■ Integrated USB2.0 Compatible 4-Port Hub
■ On-Board 24MHz Crystal Driver Circuit or 24 MHz
—
—
4 Transaction Translators for highest performance
High-Speed (480Mbits/s), Full-Speed (12Mbits/s) and
Low-Speed (1.5Mbits/s) compatible
external clock driver
■ Internal PLL for 480MHz USB2.0 Sampling
■ Internal 1.8V Linear Voltage Regulator
—
—
Full power management with per port or ganged,
selectable power control
Detects Bus-Power/Self-Power source and changes
mode automatically
■ Integrated USB termination and Pull-up/Pull-down
resistors
■ Internal Short Circuit protection of USB differential
■ Complete USB Specification 2.0 Compatibility
signal pins
—
Includes USB2.0 Transceivers
■ 1.8 Volt Low Power Core Operation
■ 3.3 Volt I/O with 5V Input Tolerance
■ VID/PID/DID, and Port Configuration for Hub via:
—
—
Single Serial I2C EEPROM
SMBus Slave Port
■ 64-Pin TQFP or 56 Pin QFN Package; green, lead-
free package also available
■ Default VID/PID/DID, allows functionality when
configuration EEPROM is absent
■ Hardware Strapping options allow for configuration
without an external EEPROM or SMBus Host
SMSC USB2504/USB2504A
PRODUCT PREVIEW
Revision 1.8 (11-11-05)
Integrated USB2.0 Compatible 4-Port Hub
ORDER NUMBER(S):
USB2504/USB2504A-JD FOR 64 PIN TQFP PACKAGE, USB2504/USB2504A-ABZJ FOR 56 PIN QFN PACKAGE AND
USB2504/USB2504A-JT FOR 64 PIN TQFP PACKAGE (GREEN, LEAD-FREE)
80 Arkay Drive
Hauppauge, NY 11788
(631) 435-6000
FAX (631) 273-3123
Copyright © 2005 SMSC or its subsidiaries. All rights reserved.
Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently,
complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be
accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any
time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this
information does not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual
property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated
version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may
contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly
sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other
application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written
approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other
SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a
registered trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective
holders.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE,
AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE
LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA,
PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT;
NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY
OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Revision 1.8 (11-11-05)
2
SMSC USB2504/USB2504A
PRODUCT PREVIEW
Integrated USB2.0 Compatible 4-Port Hub
General Description
The SMSC 4-Port Hub is fully compliant with the USB2.0 Specification and will attach to a USB host
as a Full-Speed Hub or as a Full-/High-Speed Hub. The 4-Port Hub supports Low-Speed, Full-Speed,
and High-Speed (if operating as a High-Speed Hub) downstream devices on all of the enabled
downstream ports.
A dedicated Transaction Translator (TT) is available for each downstream facing port. This architecture
ensures maximum USB throughput for each connected device when operating with mixed-speed
peripherals.
The Hub works with an external USB power distribution switch device to control VBUS switching to
downstream ports, and to limit current and sense over-current conditions.
All required resistors on the USB ports are integrated into the Hub. This includes all series termination
resistors on D+ and D– pins and all required pull-down and pull-up resistors on D+ and D– pins. The
over-current sense inputs for the downstream facing ports have internal pull-up resistors.
Throughout this document the upstream facing port of the hub will be referred to as the upstream port,
and the downstream facing ports will be called the downstream ports.
OEM Selectable Features
A default configuration is available in the USB2504/USB2504A following a reset. This configuration
may be sufficient for some applications. Strapping option pins make it possible to modify a limited sub-
set of the configuration options.
The USB2504/USB2504A may also be configured by an external EEPROM or a microcontroller. When
using the microcontroller interface, the Hub appears as an SMBus slave device. If the Hub is pin-
strapped for external EEPROM configuration but no external EEPROM is present, then a value of ‘0’
will be written to all configuration data bit fields (the hub will attach to the host with all ‘0’ values).
The 4-Port Hub supports several OEM selectable features:
■
Operation as a Self-Powered USB Hub or as a Bus-Powered USB Hub.
■
Operation as a Dynamic-Powered Hub (Hub operates as a Bus-Powered device if a local power
source is not available and switches to Self-Powered operation when a local power source is
available).
■
■
Multiple Transaction Translator (Multi-TT) or Single-TT support.
Optional OEM configuration via I2C EEPROM or via the industry standard SMBus interface from
an external SMBus Host.
■
■
■
■
■
Port power switching on an individual or ganged basis.
Port over-current monitoring on an individual or ganged basis.
LED indicator support.
Compound device support (port is permanently hardwired to a downstream USB peripheral device).
Hardware strapping options enable configuration of the following features.
Non-Removable Ports
Port Power Polarity (active high or active low logic)
Port Disable
LED support
MTT enable
Ganged Vs Port power switching and over-current sensing
SMSC USB2504/USB2504A
3
Revision 1.8 (11-11-05)
PRODUCT PREVIEW
Integrated USB2.0 Compatible 4-Port Hub
Block Diagram
To
EEPROM
or SMBus
Master
Pin
Upstream Upstream 24 MHz
1.8V Strapping
Cap Options
3.3V
USB Data
VBUS
Crystal
SD SCL
Internal
Defaults
Select
VBUS
1.8V
Reg.
Serial
PLL
Interface
Power
Detect
Upstream
PHY
Controller
SIE
Repeater
TT
#1
TT
#2
TT
#3
TT
#4
Port
Controller
Routing Logic
Port #1
Port #4
Downstream
PHY #1
OC Sense
Downstream
PHY #4
OC Sense
...
Switch Driver
LED Drivers
Switch Driver
LED Drivers
Downstream OC Switch/LED
USB Data Sense Drivers
Downstream
USB Data
OC Switch/LED
Sense Drivers
Figure 1 4-Port Block Diagram
Revision 1.8 (11-11-05)
4
SMSC USB2504/USB2504A
PRODUCT PREVIEW
Integrated USB2.0 Compatible 4-Port Hub
Package Outlines
Figure 2 64 Pin TQFP Package Outline (10x10x1.4 mm body - 2 mm footprint)
Table 1 64 Pin TQFP Package Parameters
MIN
NOMINAL
MAX
REMARKS
A
A1
A2
D
D1
E
E1
H
L
L1
e
q
W
R1
~
~
~
~
~
~
~
~
1.60
0.15
1.45
12.20
10.20
12.20
10.20
0.20
0.75
~
Overall Package Height
Standoff
0.05
1.35
11.80
9.80
11.80
9.80
0.09
0.45
~
Body Thickness
X Span
X body Size
Y Span
Y body Size
~
0.60
1.00
0.50 Basic
~
Lead Frame Thickness
Lead Foot Length
Lead Length
Lead Pitch
Lead Foot Angle
Lead Width
0o
0.17
0.08
7o
0.27
~
0.22
~
Lead Shoulder Radius
R2
ccc
0.08
~
~
~
0.20
0.08
Lead Foot Radius
Coplanarity
Notes:
1. Controlling Unit: millimeter.
2. Tolerance on the true position of the leads is ± 0.04 mm maximum.
3. Package body dimensions D1 and E1 do not include the mold protrusion.
Maximum mold protrusion is 0.25 mm per side.
4. Dimension for foot length L measured at the gauge plane 0.25 mm above the seating plane.
5. Details of pin 1 identifier are optional but must be located within the zone indicated.
SMSC USB2504/USB2504A
5
Revision 1.8 (11-11-05)
PRODUCT PREVIEW
REVISION HISTORY
DESCRIPTION
REVISION
DATE
2/07/04
10/7/04
7/2/05
RELEASED BY
S.K.ILIEV
D
D2
A
B
C
INITIAL RELEASE
REMOVE "PRELIMINARY" NOTE
D1
e
TERMINAL #1
IDENTIFIER AREA
(D/2 X E/2)
S.K.ILIEV
3
L(MAX) FROM 0.55 TO 0.50. ADDED D2/E2VARIATIONS TABLE
S.K.ILIEV
3
TERMINAL #1
IDENTIFIER AREA
(D1/2 X E1/2)
E1
E
E2
2
EXPOSED PAD
56X L
2
56X b
4X 45°X0.6 MAX (OPTIONAL)
TOP VIEW
BOTTOM VIEW
A2
A
A1
SIDE VIEW
D2 / E2 VARIATIONS
CATALOG PART
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETER.
2. POSITION TOLERANCE OF EACH TERMINAL AND EXPOSED PAD IS ± 0.05mm AT MAXIMUM MATERIAL
CONDITION. DIMENSIONS "b" APPLIES TO PLATED TERMINALS AND IT IS MEASURED BETWEEN 0.15 AND
0.30 mm FROM THE TERMINAL TIP.
3. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL BUT MUST BE LOCATED WITHIN THE AREA INDICATED.
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETERS
AND TOLERANCES ARE:
80 ARKAY DRIVE
HAUPPAUGE, NY 11788
USA
DECIMAL
ANGULAR
±1°
X.X
±0.1
X.XX ±0.05
X.XXX ±0.025
TITLE
NAME
DATE
DIM AND TOL PER ASME Y14.5M - 1994
MATERIAL
PACKAGE OUTLINE
56 TERMINAL QFN, 8x8mm BODY, 0.5mm PITCH
DRAWN S.K.ILIEV
2/06/04
-
3-D VIEWS
FINISH
CHECKED
DWG NUMBER
REV
-
S.K.ILIEV
2/07/04
2/07/04
C
MO-56-QFN-8x8
APPROVED
SCALE
STD COMPLIANCE
SHEET
PRINT WITH "SCALE TO FIT"
DO NOT SCALE DRAWING
S.K.ILIEV
1:1
JEDEC: MO-220
1 OF 1
Figure 3 56 Pin QFN Package and Parameters
相关型号:
©2020 ICPDF网 联系我们和版权申明