LPC47M14J-NC [SMSC]
128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB; 128 PIN ENGANCED超级I / O与LPC接口和USB集线器控制器型号: | LPC47M14J-NC |
厂家: | SMSC CORPORATION |
描述: | 128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
文件: | 总205页 (文件大小:1208K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LPC47M14x
128 Pin Enhanced Super I/O Controller
with an LPC Interface and USB Hub
FEATURES
ꢀ
ꢀ
ꢀ
ꢀ
3.3 Volt Operation (5 Volt Tolerant)
LPC Interface
ꢀ
Keyboard Controller
-
-
-
-
-
8042 Software Compatible
ACPI 1.0 Compliant
Fan Control
8 Bit Microcomputer
2k Bytes of Program ROM
-
-
Fan Speed Control Outputs
Fan Tachometer Inputs
256 Bytes of Data RAM
Four Open Drain Outputs Dedicated for
Keyboard/Mouse Interface
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Programmable Wake-up Event Interface
PC98, PC99 Compliant
-
Asynchronous Access to Two Data
Registers and One Status Register
Supports Interrupt and Polling Access
8 Bit Counter Timer
Dual Game Port Interface
MPU-401 MIDI Support
-
-
-
-
General Purpose Input/Output Pins
ISA Plug-and-Play Compatible Register Set
Intelligent Auto Power Management
System Management Interrupt
2.88MB Super I/O Floppy Disk Controller
Port 92 Support
Fast Gate A20 and KRESET Outputs
ꢀ
Serial Ports
-
-
Two Full Function Serial Ports
-
Licensed CMOS 765B Floppy Disk
Controller
High Speed NS16C550A Compatible UARTs
with Send/Receive 16-Byte FIFOs
Supports 230k and 460k Baud
-
Software and Register Compatible with
SMSC's Proprietary 82077AA Compatible
Core
-
Programmable Baud Rate Generator
Modem Control Circuitry
-
-
Supports Two Floppy Drives
Configurable Open Drain/Push-Pull Output
Drivers
-
480 Address and 15 IRQ Options
ꢀ
ꢀ
Infrared Port
-
-
-
-
Multiprotocol Infrared Interface
-
-
-
-
Supports Vertical Recording Format
16-Byte Data FIFO
IrDA 1.0 Compliant
SHARP ASK IR
100% IBM Compatibility
480 Addresses, Up to 15 IRQ
Detects
All
Overrun
and
Underrun
Multi-Mode Parallel Port with ChiProtect
Conditions
-
Standard Mode IBM PC/XT, PC/AT, and
PS/2 Compatible Bi-directional Parallel Port
Enhanced Parallel Port (EPP) Compatible -
EPP 1.7 and EPP 1.9 (IEEE 1284
Compliant)
-
Sophisticated Power Control Circuitry (PCC)
Including Multiple Powerdown Modes for
Reduced Power Consumption
DMA Enable Logic
-
-
-
-
Data Rate and Drive Control Registers
480 Address, Up to Eight IRQ and Four DMA
Options
-
IEEE 1284 Compliant Enhanced Capabilities
Port (ECP)
-
-
ChiProtect Circuitry for Protection
960 Address, Up to 15 IRQ and Four DMA
Options
ꢀ
Enhanced Digital Data Separator
-
2 Mbps, 1 Mbps, 500 Kbps, 300 Kbps, 250
Kbps Data Rates
-
Programmable Precompensation Modes
SMSC DS – LPC47M14X
Rev. 03/19/2001
ꢀ
USB Hub
ꢀ
ꢀ
LPC Interface
-
-
-
1 Upstream and up to 4 Downstream Ports
-
-
-
Multiplexed Command, Address and Data
Compliant with USB Spec. version 1.1
Programmable USB Manufacturer ID,
Product ID and Device Rev. Number
Number of active ports programmable or
selectable via jumpers
Bus
Serial IRQ Interface Compatible with
Serialized IRQ Support for PCI Systems
PME Interface
-
Interrupt Generating Registers
-
Powered by Vtr for Downstream Port
Wakeup
-
Registers Generate IRQ1 – 15 on Serial IRQ
Interface
ORDERING INFORMATION
Order Number: LPC47M14x – NC
128 Pin QFP Package
80 Arkay Drive
Hauppauge, NY 11788
(631) 435-6000
FAX (631) 273-3123
Copyright © SMSC 2004. All rights reserved.
Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete
information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no
responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without
notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does
not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC
or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard
Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors
known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request.
SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause
or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further
testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale
Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems
Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND
ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE.
IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES;
OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON
CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR
NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SMSC DS – LPC47M14X
Page 2
Rev. 03/19/2001
GENERAL DESCRIPTION
The LPC47M14x* is a 3.3V (5V tolerant) PC99 compliant Super I/O controller with an LPC interface and a standalone
USB hub. It is designed to be compatible with a family of Super I/O Controllers (LPC47M13x, LPC47M14x, and
LPC47M15x). To the interested reader, the LPC47M15x offers hardware monitoring capabilities. The first one
hundred pins of all these packages are completely pin compatible and offer the designer added flexibility in their
board designs. In addition, any board designed to support the LPC47M14x will automatically offer the dual capability
of supporting the LPC47M13x, as well.
The LPC47M14x implements the LPC interface, a pin reduced ISA bus interface which provides the same or better
performance as the ISA/X-bus with a substantial savings in pins used. This interface makes use of the PCI clock,
which runs at 33MHz instead of the traditional 8MHz for the ISA bus, that eases some complications found in
synchronous designs. In addition, all legacy drivers used for Super I/O components are still supported making this
new interface transparent to the supporting software. The LPC bus also supports power management, such as
wake-up and sleep modes, in the same way as the PCI bus.
The LPC47M14X incorporates a standalone USB Hub, implementing one upstream port and up to four (4)
downstream ports, with an internal data path connection for programming the USB Vendor ID, Product ID and Device
Revision Number. The number of active downstream ports is also programmable or selectable with external jumpers.
This programming is done by BIOS accessing the hub control registers.
The LPC47M14x has incorporated the following Super I/O components: a parallel port that is compatible with IBM
PC/AT architecture, as well as the IEEE 1284 EPP and ECP; two serial ports that are 16C550A UART compatible; a
keyboard/mouse controller that uses an 8042 microcontroller; two floppy controllers, which use SMSC's true CMOS
765B core; two infrared ports that are IrDA 1.0 compliant; a MIDI interface, which is a MPU-401-compatible; and 37
General Purpose I/O control functions, which offer flexibility to the system designer. The true CMOS 765B core
provides 100% compatibility with IBM PC/XT and PC/AT architectures and is software and register compatible with
the 82077AA. This chip also controls two LED’s, a dual game port interface, and the speed of two fans with fan
tachometer inputs through the use of a pulse width modulation scheme.
The LPC47M14x is ACPI 1.0 compatible and therefore supports multiple low power-down modes. It incorporates
sophisticated power control circuitry (PCC) which includes support for keyboard and mouse wake-up events.
The LPC47M14X supports the ISA Plug-and-Play Standard (Version 1.0a). The I/O Address, DMA Channel and
hardware IRQ of each logical device in the LPC47M14X may be reprogrammed through the internal configuration
registers. There are 480 (960 for Parallel Port) I/O address location options, a Serialized IRQ interface, and four
DMA channels. On chip, Interrupt Generating Registers enable external software to generate IRQ1 through IRQ15 on
the Serial IRQ Interface.
The LPC47M14X does not require any external filter components and is therefore easy to use and offers lower
system costs and reduced board area.
* The “x” in the part number is a designator that changes depending upon the particular BIOS used inside the specific
chip.
SMSC DS – LPC47M14X
Page 3
Rev. 03/19/2001
TABLE OF CONTENTS
1
2
3
PIN LAYOUT ..........................................................................................................................................................8
PIN CONFIGURATION...........................................................................................................................................9
DESCRIPTION OF PIN FUNCTIONS...................................................................................................................10
3.1
BUFFER TYPE DESCRIPTIONS...........................................................................................................................14
3.2
PINS THAT REQUIRE EXTERNAL PULLUP RESISTORS ..........................................................................................15
4
5
BLOCK DIAGRAM...............................................................................................................................................16
POWER FUNCTIONALITY...................................................................................................................................17
5.1
5.1.1
5.2
VCC POWER..................................................................................................................................................17
3 Volt Operation / 5 Volt Tolerance.........................................................................................................17
USB POWER..................................................................................................................................................17
VTR SUPPORT...............................................................................................................................................17
VREF PIN .....................................................................................................................................................17
INTERNAL PWRGOOD...................................................................................................................................18
32.768 KHZ TRICKLE CLOCK INPUT..................................................................................................................18
TRICKLE POWER FUNCTIONALITY......................................................................................................................18
MAXIMUM CURRENT VALUES............................................................................................................................19
POWER MANAGEMENT EVENTS (PME/SCI) ......................................................................................................19
5.3
5.4
5.5
5.6
5.7
5.8
5.9
6
FUNCTIONAL DESCRIPTION .............................................................................................................................20
6.1
SUPER I/O REGISTERS....................................................................................................................................20
HOST PROCESSOR INTERFACE (LPC)...............................................................................................................20
LPC INTERFACE .............................................................................................................................................21
LPC Interface Signal Definition...............................................................................................................21
LPC Cycles.............................................................................................................................................21
Field Definitions......................................................................................................................................21
LFRAME# Usage....................................................................................................................................21
I/O Read and Write Cycles .....................................................................................................................22
DMA Read and Write Cycles..................................................................................................................22
DMA Protocol .........................................................................................................................................22
Power Management................................................................................................................................22
SYNC Protocol .......................................................................................................................................22
6.2
6.3
6.3.1
6.3.2
6.3.3
6.3.4
6.3.5
6.3.6
6.3.7
6.3.8
6.3.9
6.3.10 LPC Transfer ..........................................................................................................................................23
6.4
6.4.1
USB HUB FUNCTIONAL DESCRIPTION...............................................................................................................24
USB Downstream Port Selection............................................................................................................25
FLOPPY DISK CONTROLLER ....................................................................................................................26
FDC Internal Registers ...........................................................................................................................27
STATUS REGISTER ENCODING..........................................................................................................37
Instruction Set.........................................................................................................................................43
DATA TRANSFER COMMANDS............................................................................................................50
SERIAL PORT (UART) ................................................................................................................................60
INFRARED INTERFACE..............................................................................................................................72
MPU-401 MIDI UART...................................................................................................................................73
Overview.................................................................................................................................................73
Host Interface .........................................................................................................................................73
MIDI Data Port........................................................................................................................................74
Status Port..............................................................................................................................................74
MPU-401 Command Controller ..............................................................................................................76
MIDI UART .............................................................................................................................................77
MPU-401 Configuration Registers..........................................................................................................77
PARALLEL PORT........................................................................................................................................78
IBM XT/AT Compatible, Bi-Directional and EPP Modes.........................................................................79
Extended Capabilities Parallel Port.........................................................................................................84
POWER MANAGEMENT.............................................................................................................................94
SERIAL IRQ.................................................................................................................................................98
INTERRUPT GENERATING REGISTERS..............................................................................................................101
6.5
6.5.1
6.5.2
6.5.3
6.5.4
6.6
6.7
6.8
6.8.1
6.8.2
6.8.3
6.8.4
6.8.5
6.8.6
6.8.7
6.9
6.9.1
6.9.2
6.10
6.11
6.12
6.13 8042 KEYBOARD CONTROLLER DESCRIPTION ...................................................................................102
6.13.1 Keyboard Interface ...............................................................................................................................103
6.13.2 External Keyboard and Mouse Interface...............................................................................................104
6.13.3 Keyboard Power Management .............................................................................................................104
6.13.4 Interrupts ..............................................................................................................................................104
6.13.5 Memory Configurations.........................................................................................................................104
6.13.6 Register Definitions...............................................................................................................................105
SMSC DS – LPC47M14X
Page 4
Rev. 03/19/2001
6.13.7 External Clock Signal............................................................................................................................105
6.13.8 Default Reset Conditions......................................................................................................................105
6.13.9 Latches On Keyboard and Mouse IRQs ...............................................................................................108
6.13.10 Keyboard and Mouse PME Generation ................................................................................................109
6.14 GENERAL PURPOSE I/O..........................................................................................................................110
6.14.1 GPIO Pins.............................................................................................................................................110
6.14.2 Description............................................................................................................................................111
6.14.3 GPIO Control........................................................................................................................................112
6.14.4 GPIO Operation....................................................................................................................................112
6.14.5 GPIO PME and SMI Functionality.........................................................................................................113
6.14.6 Either Edge Triggered Interrupts...........................................................................................................114
6.14.7 LED Functionality..................................................................................................................................115
6.15
SYSTEM MANAGEMENT INTERRUPT (SMI)...........................................................................................115
6.15.1 SMI Registers.......................................................................................................................................115
6.16
PME SUPPORT.........................................................................................................................................116
6.16.1 ‘Wake on Specific Key’ Option..............................................................................................................117
6.17 FAN SPEED CONTROL AND MONITORING............................................................................................118
6.17.1 Fan Speed Control................................................................................................................................118
6.17.2 Fan Tachometer Inputs.........................................................................................................................119
6.18 SECURITY FEATURE ...............................................................................................................................122
6.18.1 GPIO Device Disable Register Control.................................................................................................122
6.18.2 Device Disable Register .......................................................................................................................122
6.19
GAME PORT LOGIC..................................................................................................................................122
6.19.1 Power Control Register.........................................................................................................................124
6.19.2 VREF Pin..............................................................................................................................................124
7
8
9
RUNTIME REGISTERS......................................................................................................................................125
CONFIGURATION..............................................................................................................................................152
OPERATIONAL DESCRIPTION ........................................................................................................................172
9.1
MAXIMUM GUARANTEED RATINGS...................................................................................................................172
9.2
DC ELECTRICAL CHARACTERISTICS................................................................................................................172
10 TIMING DIAGRAMS...........................................................................................................................................177
11 PACKAGE OUTLINE .........................................................................................................................................200
12 APPENDIX - TEST MODE..................................................................................................................................201
12.1
BOARD TEST MODE.......................................................................................................................................201
12.1.1 XNOR-Chain Test Mode.......................................................................................................................201
13 REFERENCE DOCUMENTS..............................................................................................................................204
14 LPC47M14X REVISIONS...................................................................................................................................205
TABLES
Table 1 – Super I/O Block Addresses ........................................................................................................................20
Table 2 – Hub Descriptor to be Modified....................................................................................................................25
Table 3 – Status, Data and Control Registers............................................................................................................27
Table 4 – Tape Select Bits.........................................................................................................................................30
Table 5 – Internal 2 Drive Decode - Normal...............................................................................................................30
Table 6 – Internal 2 Drive Decode - Drives 0 and 1 Swapped ...................................................................................31
Table 7 – Drive Type ID .............................................................................................................................................31
Table 8 – Precompensation Delays ...........................................................................................................................32
Table 9 – Data Rates .................................................................................................................................................33
Table 10 – DRVDEN Mapping ...................................................................................................................................33
Table 11 – Default Precompensation Delays.............................................................................................................33
Table 12 – FIFO Service Delay..................................................................................................................................35
Table 13 – Status Register 0......................................................................................................................................37
Table 14 – Status Register 1......................................................................................................................................38
Table 15 – Status Register 2......................................................................................................................................38
Table 16 – Status Register 3......................................................................................................................................39
Table 17 – Description of Command Symbols...........................................................................................................41
Table 18 – Instruction Set ..........................................................................................................................................43
Table 19 – Sector Sizes.............................................................................................................................................50
Table 20 – Effects of MT and N Bits...........................................................................................................................51
Table 21 – Skip Bit vs Read Data Command.............................................................................................................51
SMSC DS – LPC47M14X
Page 5
Rev. 03/19/2001
Table 22 – Skip Bit vs. Read Deleted Data Command...............................................................................................51
Table 23 – Result Phase Table..................................................................................................................................52
Table 24 – Verify Command Result Phase Table ......................................................................................................53
Table 25 – Typical Values for Formatting...................................................................................................................55
Table 26 – Interrupt Identification...............................................................................................................................56
Table 27 – Drive Control Delays (ms) ........................................................................................................................57
Table 28 – Effects of WGATE and GAP Bits..............................................................................................................59
Table 29 – Addressing the Serial Port........................................................................................................................60
Table 30 – Interrupt Control Table .............................................................................................................................63
Table 31 – Baud Rates ..............................................................................................................................................68
Table 32 – Reset Function Table ...............................................................................................................................69
Table 33 – Register Summary for an Individual UART Channel ................................................................................69
Table 34 – MPU-401 HOST INTERFACE REGISTERS ............................................................................................74
Table 35 – MIDI DATA PORT ....................................................................................................................................74
Table 36 – MPU-401 STATUS PORT........................................................................................................................74
Table 37 – MIDI RECEIVE BUFFER EMPTY STATUS BIT.......................................................................................75
Table 38 – MIDI TRANSMIT BUSY STATUS BIT......................................................................................................75
Table 39 – MPU-401 COMMAND PORT ...................................................................................................................75
Table 40 – Parallel Port Connector ............................................................................................................................79
Table 41 – EPP Pin Descriptions ...............................................................................................................................83
Table 42 – ECP Pin Descriptions...............................................................................................................................85
Table 43 – ECP Register Definitions..........................................................................................................................86
Table 44 – Mode Descriptions....................................................................................................................................86
Table 45a – Extended Control Register .....................................................................................................................90
Table 46 – Channel/Data Commands supported in ECP mode .................................................................................92
Table 47 – PC/AT and PS/2 Available Registers .......................................................................................................95
Table 48 – State of System Pins in Auto Powerdown ................................................................................................96
Table 49 – State of Floppy Disk Drive Interface Pins in Powerdown..........................................................................96
Table 50 – I/O Address Map ....................................................................................................................................103
Table 51 – Host Interface Flags ...............................................................................................................................103
Table 52 – Status Register.......................................................................................................................................105
Table 53 – Resets....................................................................................................................................................105
Table 54 – General Purpose I/O Port Assignments .................................................................................................111
Table 55 – GPIO Configuration Summary................................................................................................................112
Table 56 – GPIO Read/Write Behavior ....................................................................................................................113
Table 57 – Different Modes for Fan..........................................................................................................................118
Table 58 – Runtime Register Block Summary..........................................................................................................125
Table 59 – PME, SMI, GPIO, FAN Register Description..........................................................................................127
Table 60 – Game Port..............................................................................................................................................151
Table 61 – LPC47M14x Configuration Registers Summary.....................................................................................154
Table 62 – Chip Level Registers ..............................................................................................................................156
Table 63 – Logical Device Registers........................................................................................................................159
Table 64 – Logical Device Registers........................................................................................................................160
Table 65 – I/O Base Address Configuration Register Description............................................................................161
Table 66 – Interrupt Select Configuration Register Description ...............................................................................162
Table 67 – DMA Channel Select Configuration Register Description.......................................................................163
Table 68 – Floppy Disk Controller, Logical Device 0 [Logical Device Number = 0x00]............................................164
Table 69 – Parallel Port, Logical Device 3 [Logical Device Number = 0x03]............................................................165
Table 70 – Serial Port 1, Logical Device 4 [Logical Device Number = 0x04]............................................................166
Table 71 – Serial Port 2, Logical Device 5 [Logical Device Number = 0x05]............................................................166
Table 72 – KYBD, Logical Device 7 [Logical Device Number = 0x07] .....................................................................168
Table 73 – PME, Logical Device A [Logical Device Number = 0x0A].......................................................................168
Table 74 – MPU-401 [Logical Device Number = 0x0B]............................................................................................169
Table 75 – USB Hub, Logical Device C [Logical Device Number = 0x0C] ...............................................................169
Table 76 – HubControl_1 Register Definition...........................................................................................................171
Table 77 – Electrical Source Characteristics............................................................................................................178
SMSC DS – LPC47M14X
Page 6
Rev. 03/19/2001
FIGURES
FIGURE 1 – LPC47M14X BLOCK DIAGRAM...........................................................................................................16
FIGURE 2 – LPC47M14X CLOCK GENERATOR .....................................................................................................24
FIGURE 3 – MPU-401 MIDI INTERFACE..................................................................................................................73
FIGURE 4 – MPU-401 INTERRUPT..........................................................................................................................76
FIGURE 5 - MIDI DATA BYTE EXAMPLE...................................................................................................................77
FIGURE 6 – KEYBOARD LATCH............................................................................................................................108
FIGURE 7 – MOUSE LATCH...................................................................................................................................108
FIGURE 8 – GPIO FUNCTION ILLUSTRATION......................................................................................................112
FIGURE 9 – POWER-UP TIMING ...........................................................................................................................178
FIGURE 10 – DATA SIGNAL RISE AND FALL TIME..............................................................................................180
FIGURE 11 – FULL SPEED LOAD..........................................................................................................................180
FIGURE 12 – LOW-SPEED PORT LOADS.............................................................................................................180
FIGURE 13 – CABLE DELAY..................................................................................................................................180
FIGURE 14 – DIFFERENTIAL DATA JITTER..........................................................................................................181
FIGURE 15 – DIFFERENTIAL TO EOP TRANSITION SKEW AND EOP WIDTH...................................................181
FIGURE 16 – RECEIVER JITTER TOLERANCE ....................................................................................................181
FIGURE 17 – INPUT CLOCK TIMING.....................................................................................................................182
FIGURE 18 – PCI CLOCK TIMING..........................................................................................................................182
FIGURE 19 – RESET TIMING .................................................................................................................................182
FIGURE 20 – OUTPUT TIMING MEASUREMENT CONDITIONS, LPC SIGNALS.................................................183
FIGURE 21 – INPUT TIMING MEASUREMENT CONDITIONS, LPC SIGNALS.....................................................183
FIGURE 22 – I/O WRITE .........................................................................................................................................184
FIGURE 23 – I/O READ...........................................................................................................................................184
FIGURE 24 – DMA REQUEST ASSERTION THROUGH LDRQ#...........................................................................185
FIGURE 25 – DMA WRITE (FIRST BYTE)..............................................................................................................185
FIGURE 26 – DMA READ (FIRST BYTE)................................................................................................................185
FIGURE 27 – FLOPPY DISK DRIVE TIMING (AT MODE ONLY) ...........................................................................186
FIGURE 28 – EPP 1.9 DATA OR ADDRESS WRITE CYCLE.................................................................................187
FIGURE 29 – EPP 1.9 DATA OR ADDRESS READ CYCLE ..................................................................................188
FIGURE 30 – EPP 1.7 DATA OR ADDRESS WRITE CYCLE.................................................................................189
FIGURE 31 – EPP 1.7 DATA OR ADDRESS READ CYCLE ..................................................................................189
FIGURE 32 – PARALLEL PORT FIFO TIMING.......................................................................................................191
FIGURE 33 – ECP PARALLEL PORT FORWARD TIMING ....................................................................................191
FIGURE 34 – ECP PARALLEL PORT REVERSE TIMING......................................................................................192
FIGURE 35 – IRDA RECEIVE TIMING....................................................................................................................193
FIGURE 36 – IRDA TRANSMIT TIMING .................................................................................................................194
FIGURE 37 – AMPLITUDE SHIFT KEYED IR RECEIVE TIMING...........................................................................195
FIGURE 38 – AMPLITUDE SHIFT KEYED IR TRANSMIT TIMING ........................................................................196
FIGURE 39 – SETUP AND HOLD TIME..................................................................................................................197
FIGURE 40 – SERIAL PORT DATA ........................................................................................................................197
FIGURE 41 – JOYSTICK POSITION SIGNAL.........................................................................................................197
FIGURE 42 – JOYSTICK BUTTON SIGNAL ...........................................................................................................197
FIGURE 43 – KEYBOARD/MOUSE RECEIVE/SEND DATA TIMING.....................................................................198
FIGURE 44 – MIDI DATA BYTE..............................................................................................................................198
FIGURE 45 – FAN OUTPUT TIMING ......................................................................................................................199
FIGURE 46 – FAN TACHOMETER INTPUT TIMING..............................................................................................199
FIGURE 47 – LED OUTPUT TIMING ......................................................................................................................199
FIGURE 48 – 128 PIN QFP PACKAGE OUTLINE...................................................................................................200
FIGURE 49 – XNOR-CHAIN TEST STRUCTURE...................................................................................................201
SMSC DS – LPC47M14X
Page 7
Rev. 03/19/2001
1
PIN LAYOUT
1
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
VSS
GP40/DRVDEN0
2
VSS
GP41/DRVDEN1
3
GP57/nDTR2
GP56/nCTS2
GP55/nRTS2
GP54/nDSR2
GP53/TXD2 (IRTX)
GP52/RXD2 (IRRX)
GP51/nDCD2
VCC
nMTR0
4
nDSKCHG
5
nDS0
6
CLKI32
7
VSS
8
nDIR
9
nSTEP
10
nWDATA
11
GP50/nRI2
nDCD1
nRI1
nWGATE
12
nHDSEL
13
nINDEX
14
nDTR1
nCTS1
nRTS1
nDSR1
TXD1
nTRK0
15
nWRTPRT
16
nRDATA
17
GP42/nIO_PME
18
VTR
LPC47M14x
128 PIN QFP
19
RXD1
CLOCKI
20
nSTROBE
nALF
LAD0
21
LAD1
22
nERROR
nACK
LAD2
23
LAD3
24
BUSY
LFRAME#
25
PE
LDRQ#
26
SLCT
PCI_RESET#
27
VSS
LPCPD#
28
PD7
GP43/DDRC
29
PD6
PCI_CLK
30
PD5
SER_IRQ
31
PD4
VSS
32
PD3
GP10 /J1B1
33
PD2
GP11 /J1B2
34
PD1
GP12 /J2B1
35
PD0
GP13 /J2B2
36
nSLCTIN
nINIT
GP14 /J1X
37
GP15 /J1Y
38
VCC
GP16 /J2X
SMSC DS – LPC47M14X
Page 8
Rev. 03/19/2001
2
PIN CONFIGURATION
PIN #
NAME
PIN #
NAME
GP11 /J1B2
GP12 /J2B1
GP13 /J2B2
GP14 /J1X
PIN #
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
NAME
PIN #
97
NAME
GP54/nDSR2
GP55/nRTS2
GP56/nCTS2
GP57/nDTR2
VSS
1
GP40/DRVDEN0 33
GP41/DRVDEN1 34
VCC
2
nINIT
98
3
nMTR0
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
nSLCTIN
PD0
99
4
nDSKCHG
nDS0
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
5
GP15 /J1Y
PD1
6
CLKI32
GP16 /J2X
PD2
VSS
7
VSS
nDIR
GP17 /J2Y
PD3
USB +
8
AVSS
PD4
USB -
9
nSTEP
GP20/P17
PD5
PD1 +
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
nWDATA
nWGATE
nHDSEL
nINDEX
nTRK0
GP21/P16/nDS1
GP22/P12/nMTR1
VREF
PD6
PD1 -
PD7
PD2 +
VSS
PD2 -
GP24/SYSOPT
GP25/MIDI_IN
GP26/MIDI_OUT
GP60/LED1
GP61/LED2
GP27/nIO_SMI
SLCT
PD3 +
PE
PD3 -
nWRTPRT
nRDATA
GP42/nIO_PME
VTR
BUSY
nACK
PD4 +
PD4 -
nERROR
nALF
VTR
nPWREN1
nPWREN2
nPWREN3
nPWREN4
nUSBOC1
nUSBOC2
nUSBOC3
nUSBOC4
VTR
CLOCKI
LAD0
GP30/FAN_TACH2 83
GP31/FAN_TACH1 84
nSTROBE
RXD1
LAD1
VCC
85
86
87
88
89
90
91
92
93
94
95
TXD1
LAD2
GP32/FAN2
GP33/FAN1
KDAT
nDSR1
nRTS1
nCTS1
nDTR1
nRI1
LAD3
LFRAME#
LDRQ#
KCLK
PCI_RESET#
LPCPD#
GP43/DDRC
PCI_CLK
SER_IRQ
VSS
MDAT
MCLK
nDCD1
GP50/nRI2
VCC
GP51/nDCD2
GP52/RXD2
(IRRX)
GP53/TXD2
(IRTX)
ICLK
VSS
OCLK
IRRX2/GP34
IRTX2/GP35
GP36/nKBDRST
VCC
nStrp0
nStrp1
32
GP10 /J1B1
64
GP37/A20M
96
128
VSS
Note: The chip is part of a family of LPC chips (LPC47M13x, LPC47M14x, and LPC47M15x). The first 100 pins of
these chips are pin compatible, which adds more flexibility for the board designer. In addition, a board designed for
the LPC47M14x can also support the LPC47M13x with little or no changes made to the board design.
SMSC DS – LPC47M14X
Page 9
Rev. 03/19/2001
3
DESCRIPTION OF PIN FUNCTIONS
BUFFER
TYPE
BUFFER TYPE
PER FUNCTION
(NOTE 1)
QFP
NAME
TOTAL
SYMBOL
NOTES
PIN #
PROCESSOR/HOST LPC INTERFACE (10)
23:20
Multiplexed
Command,
4
LAD[3:0]
PCI_IO
PCI_IO
Address, Data [3:0]
Frame
PCI_I
PCI_O
PCI_I
PCI_I
PCI_ICLK
PCI_IO
24
25
26
27
29
30
1
1
1
1
1
1
LFRAME#
LDRQ#
PCI_RESET# PCI_I
LPCPD#
PCI_CLK
SER_IRQ
CLOCKS (4)
CLOCKI32
PCI_I
PCI_O
Encoded DMA Request
PCI Reset
Power Down
PCI Clock
2
3
PCI_I
PCI_ICLK
PCI_IO
Serial IRQ
IS
6
32.768KHz Trickle Clock
Input
1
IS
19
123
14.318MHz Clock Input
1
1
CLOCKI
ICLK
IS
IS
IS
IS
11, 14
14
24MHz Crystal (terminal 1)
/ 48MHz Clock Input
124
51
52
54
55
24MHz Crystal (terminal 2)
1
1
1
1
1
OCLK
FAN CONTROL (4)
IS
IS
(I/O8/OD8)/I
(I/O8/OD8)/I
General Purpose I/O
/Fan Tachometer 2
General Purpose I/O
/Fan Tachometer 1
General Purpose I/O
/Fan Speed Control 2
General Purpose I/O
/Fan Speed Control 1
GP30/
IO8
FAN_TACH2
GP31/
IO8
FAN_TACH1
(I/O12/OD12)/
(O12/OD12)
(I/O12/OD12)/
(O12/OD12)
4
4
GP32/FAN2
GP33/FAN1
IO12
IO12
INFRARED INTERFACE (2)
IS/(IS/O8/OD8)
61
62
Infrared Rx
1
IRRX2/GP34
IS/O8
/General Purpose I/O
Infrared Tx
O12/(I/O12/OD12)
5, 6
1
IRTX2/GP35
IO12
/General Purpose I/O
POWER PINS (16)
VCC
53,
Power
4
7
65,93,1
25
7, 31,
60,76,
101,
Ground
VSS
102,
128
40
44
18,
113,
122
Analog Ground
Reference Voltage
Trickle Voltage
1
1
3
AVSS
VREF
VTR
7
FDD INTERFACE (14)
IS
16
11
10
Read Disk Data
Write Gate
Write Disk Data
1
1
1
nRDATA
nWGATE
nWDATA
IS
O12
O12
(O12/OD12)
(O12/OD12)
SMSC DS – LPC47M14X
Page 10
Rev. 03/19/2001
BUFFER
TYPE
BUFFER TYPE
PER FUNCTION
(NOTE 1)
(O12/OD12)
(O12/OD12)
(O12/OD12)
IS
QFP
NAME
Head Select
Step Direction
Step Pulse
Disk Change
Drive Select 0
Motor On 0
Write Protected
Track 0
TOTAL
SYMBOL
nHDSEL
NOTES
PIN #
12
8
9
4
5
1
1
1
1
1
1
1
1
1
1
O12
nDIR
O12
O12
IS
O12
O12
IS
IS
IS
IO12
nSTEP
nDSKCHG
nDS0
nMTR0
nWRTPRT
nTRKO
nINDEX
(O12/OD12)
(O12/OD12)
3
IS
IS
IS
15
14
13
1
Index Pulse Input
(I/O12/OD12)/
General Purpose I/O/Drive
GP40/
(O12/OD12)
Density Select 0
DRVDEN0
(I/O12/OD12)/
(O12/OD12)
2
General Purpose I/O/Drive
Density Select 1
1
GP41/
IO12
DRVDEN1
SERIAL PORT 1 INTERFACE (8)
84
85
87
88
89
86
91
90
Receive Serial Data 1
Transmit Serial Data 1
Request to Send 1
Clear to Send 1
Data Terminal Ready 1
Data Set Ready 1
Data Carrier Detect 1
Ring Indicator 1
1
1
1
1
1
1
1
1
RXD1
TXD1
IS
O12
O8
I
IS
O12
O8
I
nRTS1
nCTS1
nDTR1
nDSR1
nDCD1
nRI1
O6
O6
I
I
I
I
I
I
SERIAL PORT 2 INTERFACE (8)
(IS/O8/OD8)/IS
95
96
General Purpose I/O
1
GP52/RXD2
IS/O8
(IRRX)
/Receive Serial Data
2
/Infrared Rx
General Purpose I/O
(I/O12/OD12)/O12
5
1
GP53/TXD2
(IRTX)
IO12
/Transmit Serial Data 2
/Infrared Tx
(I/O8/OD8)/O8
(I/O8/OD8)/I
(I/O8/OD8)/O8
(I/O8/OD8)/I
98
99
General Purpose I/O
/Request to Send 2
General Purpose I/O
/Clear to Send 2
General Purpose I/O
/Data Terminal Ready
General Purpose I/O
/Data Set Ready 2
1
1
1
1
GP55/nRTS2
GP56/nCTS2
GP57/nDTR2
GP54/nDSR2
IO8
IO8
IO8
IO8
100
97
94
92
General Purpose I/O/Data
1
1
GP51/nDCD2 IO8
GP50/nRI2 IO8
(I/O8/OD8)/I
(I/O8/OD8)/I
Carrier Detect 2
General Purpose I/O/Ring
Indicator 2
PARALLEL PORT INTERFACE (17)
66
67
68
69
70
71
72
73
74
Initiate Output
Printer Select Input
Port Data 0
Port Data 1
Port Data 2
Port Data 3
Port Data 4
Port Data 5
Port Data 6
nINIT
nSLCTIN
PD0
OP14
OP14
IOP14
IOP14
IOP14
IOP14
IOP14
IOP14
IOP14
(OD14/OP14)
(OD14/OP14)
IOP14
IOP14
IOP14
IOP14
IOP14
IOP14
IOP14
1
1
1
1
1
1
1
1
1
PD1
PD2
PD3
PD4
PD5
PD6
SMSC DS – LPC47M14X
Page 11
Rev. 03/19/2001
BUFFER
TYPE
BUFFER TYPE
PER FUNCTION
(NOTE 1)
QFP
NAME
Port Data 7
Printer Selected Status
Paper End
Busy
Acknowledge
Error
Autofeed Output
Strobe Output
TOTAL
SYMBOL
PD7
SLCT
PE
BUSY
nACK
nERROR
nALF
NOTES
PIN #
75
77
78
79
80
81
82
83
IOP14
IOP14
I
I
I
I
I
1
1
1
1
1
1
1
1
I
I
I
I
I
OP14
OP14
(OD14/OP14)
(OD14/OP14)
nSTROBE
KEYBOARD/MOUSE INTERFACE (6)
IOD16
IOD16
IOD16
IOD16
56
57
58
59
63
Keyboard Data
Keyboard Clock
Mouse Data
1
1
1
1
1
KDAT
KCLK
MDAT
MCLK
IOD16
IOD16
IOD16
IOD16
IO8
Mouse Clock
(I/O8/OD8)/O8
9
9
General Purpose I/O
/Keyboard Reset
General Purpose I/O
/Gate A20
GP36/
nKBDRST
(I/O8/OD8)/O8
64
1
GP37/A20M
IO8
USB HUB(18)
USB+
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
IOUSB
103
104
105
106
107
108
109
110
111
112
Serial Port Upstream Data
+
1
1
1
1
1
1
1
1
1
1
USB-
PD1+
PD 1-
PD 2+
PD 2-
PD 3+
PD 3-
PD 4+
PD 4-
Serial Port Upstream Data
-
Serial Port Downstream
Data +
Serial Port Downstream
Data -
Serial Port Downstream
Data +
Serial Port Downstream
Data -
Serial Port Downstream
Data +
Serial Port Downstream
Data -
Serial Port Downstream
Data +
Serial Port Downstream
Data -
nUSBOC1
nPWREN1
nUSBOC2
nPWREN2
nUSBOC3
nPWREN3
nUSBOC4
nPWREN4
nStrp0
IPU
O24
IPU
O24
IPU
O24
IPU
O24
IPU
13
13
13
13
13
13
13
13
118
114
119
115
120
116
121
117
126
USB Over-Current sense
USB Power Enable
USB Over-Current sense
USB Power Enable
USB Over-Current sense
USB Power Enable
1
1
1
1
1
1
1
1
1
IPU
O24
IPU
O24
IPU
O24
IPU
O24
IPU
USB Over-Current sense
USB Power Enable
Input with
30ua Pull
Up
Input with
30ua Pull
Up
Number of Down Stream
Ports select
nStrp1
IPU
127
Number of Down Stream
Ports select
1
IPU
SMSC DS – LPC47M14X
Page 12
Rev. 03/19/2001
BUFFER
TYPE
BUFFER TYPE
PER FUNCTION
(NOTE 1)
QFP
NAME
TOTAL
SYMBOL
NOTES
PIN #
GENERAL PURPOSE I/O (19)
General
Purpose
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
GP10 /J1B1
GP11 /J1B2
GP12 /J2B1
GP13 /J2B2
GP14 /J1X
GP15 /J1Y
GP16 /J2X
GP17 /J2Y
GP20 /P17
IS/O8
IS/O8
IS/O8
IS/O8
IO12
IO12
IO12
IO12
IO8
(IS/O8/OD8)/IS
32
33
34
35
36
37
38
39
1
1
1
1
1
1
1
1
/Joystick 1 Button 1
General
/Joystick 1 Button 2
General Purpose
/Joystick 2 Button 1
General Purpose
/Joystick 2 Button 2
General Purpose
Purpose
(IS/O8/OD8)/IS
(IS/O8/OD8)/IS
(IS/O8/OD8)/IS
(I/O12/OD12)/ IO12
(I/O12/OD12)/ IO12
(I/O12/OD12)/ IO12
(I/O12/OD12)/ IO12
(I/O8/OD8)/IO8
(I/O12/OD12)/
IO12/(O12/OD12)
(I/O12/OD12)/
IO12/(O12/OD12)
(I/O8/OD8)
/Joystick 1 X-Axis
General
Purpose
/Joystick 1 Y-Axis
General
Purpose
/Joystick 2 X-Axis
General
Purpose
/Joystick 2 Y-Axis
General Purpose I/O / P17
41
42
1
1
General Purpose I/O / P16
GP21 /P16/ IO12
/nDS1
nDS1
General Purpose I/O / P12
/nMTR1
GP22 /P12/ IO12
nMTR1
43
45
46
47
50
1
1
1
1
1
General Purpose I/O
System Option
/
GP24
IO8
8
/SYSOPT
GP25
General
Purpose
I/O
I/O
IO8
(I/O8/OD8)/I
/MIDI_IN
General
/MIDI_IN
GP26
Purpose
IO12
IO12
(I/O12/OD12)/O12
(I/O12/OD12)/ OD12
/MIDI_OUT
/MIDI_OUT
General Purpose I/O
/SMI Output
General Purpose I/O
GP27
/nIO_SMI
/
/
/
GP60 /LED1
IO12
IO12
IO12
(I/O12/OD12)/O12
(I/O12/OD12)/O12
(I/O12/OD12)/ OD12
10
10
48
49
17
1
1
1
LED
General Purpose I/O
LED
GP61 /LED2
General Purpose I/O
GP42
Power Management Event
General Purpose I/O
/nIO_PME
GP43/DDRC
IO8
(I/O8/OD8)/I
28
1
/Device
Disable
Reg.
Control
Note:
The "n" as the first letter of a signal name or the “#” as the suffix of a signal name indicates an "Active Low"
signal.
Note 1: Buffer types per function on multiplexed pins are separated by a slash “/”. Buffer types in parenthesis
represent multiple buffer types for a single pin function.
Note 2: The LPCPD# pin may be tied high. The LPC interface will function properly if the PCI_RESET# signal
follows the protocol defined for the LRESET# signal in the “Low Pin Count Interface Specification”.
Note 3: For USB Hub functionality, the 32 KHz input clock must always be connected. There is a bit in the
configuration register at 0xF0 in Logical Device A that indicates whether or not the 32KHz clock is
connected. This bit determines the clock source for the fan tachometer, LED and “wake on specific key”
logic. This bit must always be set to ‘0’ (‘0’=32 KHz clock connected; reset default=‘0’).
Note 4: The fan control pins (FAN1 and FAN2) come up as outputs and low following a VCC POR and Hard Reset.
These pins revert to their non-inverting GPIO input function when VCC is removed from the part.
Note 5: The IRTX pins (IRTX2/GP35 and GP53/TXD2 (IRTX)) are driven low when the part is powered by VTR
(VCC=0V with VTR=3.3V). These pins will remain low following a power-up (VCC POR) until serial port 2
is enabled by setting the activate bit, at which time the pin will reflect the state of the transmit output of the
Serial Port 2 block.
Note 6: The VCC power-up default for this pin is Logic “0” if the IRTX function is programmed on the GPIO.
Note 7: VTR must not be connected to VCC. The 32 KHz input clock must not be driven high whenVTR = 0v.
SMSC DS – LPC47M14X
Page 13
Rev. 03/19/2001
Note 8: The GP24 /SYSOPT pin requires an external pulldown resistor to put the base IO address for configuration
at 0x02E. An external pullup resistor is required to move the base IO address for configuration to 0x04E.
Note 9: External pullups must be placed on the nKBDRST and A20M pins. These pins are GPIOs that are inputs
after an initial power-up (VTR POR). If the nKBDRST and A20M functions are to be used the system must
ensure that these pins are high. See Section “Pins That Require External Pullup Resistor”.
Note 10: The LED pins are powered by VTR so that the LEDs can be controlled when the part is under VTR power.
Note 11: The 48MHz clock input must not be driven high when VTR = 0V.
Note 12: VTR is used to power the USB cable transceivers. VTR must not be connected to VCC.
Note 13: When the specified USB Down Stream Ports are disabled via the Strp0/Strp1 bit or nStrp1/nStrp0 Pins, the
associated Over-current sense pins (nUSBOC[x]) and Power Enable (nPWREN[4:1]) pins are also
disabled. The USB Down Stream Port nUSBOC[x] input pin can be a NC (No Connect) pin for existing
designs or tied High (1). For EMI and reduced Noise sensitivity, it is recommended that the pin be tied High
(1). The Power Enable (nPWREN[x]) pin will be forced low (0).
Note 14: When a 24MHz crystal oscillator is used, these pins need off-balance capacitive loading. It is suggested to
use a 22pf capacitor on ICLK and a 10pf capacitor on OCLK.
3.1 BUFFER TYPE DESCRIPTIONS
Note: The buffer type values are specified at VCC=3.3V
IO12
O12
Input/Output, 12mA sink, 6mA source.
Output, 12mA sink, 6mA source.
OD12
O6
Open Drain Output, 12mA sink.
Output, 6mA sink, 3mA source.
O8
Output, 8mA sink, 4mA source.
OD8
OD14
OP14
IOP14
IOD16
IO8
Open Drain Output, 8mA sink.
Open Drain Output, 14mA sink.
Output, 14mA sink, 14mA source.
Input/Output, 14mA sink, 14mA source. Back-drive protected.
Input/Output (Open Drain), 16mA sink.
Input/Output, 8mA sink, 4mA source.
O24
Output, 24mA sink, 12mA source.
I
Input TTL Compatible.
IPU
Input TTL Compatible. With 30ua internal Pull Up
Input with Schmitt Trigger.
IS
PCI_IO
PCI_O
PCI_I
PCI_ICLK
IOUSB
Input/Output. These pins must meet the PCI 3.3V AC and DC Characteristics. (Note 1)
Output. These pins must meet the PCI 3.3V AC and DC Characteristics. (Note 1)
Input. These pins must meet the PCI 3.3V AC and DC Characteristics. (Note 1)
Clock Input. These pins must meet the PCI 3.3V AC and DC Characteristics and timing. (Note 2)
Buffer Type for the USB differential data lines. Defined in the “Operational Description”
section according to the USB specification; V1.1
Note 1: See the “PCI Local Bus Specification,” Revision 2.1, Section 4.2.2.
Note 2: See the “PCI Local Bus Specification,” Revision 2.1, Section 4.2.2 and 4.2.3.
SMSC DS – LPC47M14X
Page 14
Rev. 03/19/2001
3.2 PINS THAT REQUIRE EXTERNAL PULLUP RESISTORS
The following pins require external pullup resistors:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
KDAT
KCLK
MDAT
MCLK
GP36/KBDRST if KBDRST function is used
GP37/A20M if A20M function is used
GP20/P17 If P17 function is used
GP21/P16 if P16 function is used
GP22/P12 if P12 function is used
GP27/nIO_SMI if nIO_SMI function is used as Open Collector output.
GP42/nIO_PME if nIO_PME function is used as Open Collector output.
SER_IRQ
GP40/DRVDEN0 if DRVDEN0 function is used as Open Collector.
GP41/DRVDEN1 if DRVDEN1 function is used as Open Collector.
nMTR0 if used as Open Collector Output
nDS0 if used as Open Collector Output
nDIR if used as Open Collector Output
nSTEP if used as Open Collector Output
nWDATA if used as Open Collector Output
nWGATE if used as Open Collector Output
nHDSEL if used as Open Collector Output
nINDEX
nTRK0
nWRTPRT
nRDATA
nDSKCHG
SMSC DS – LPC47M14X
Page 15
Rev. 03/19/2001
4
BLOCK DIAGRAM
2nd Infrared Port
Game Port
Fan Control
LEDs
CLK32
CLOCKI
CLOCK GEN
PD[7,0]
SER_IRQ
PCI_CLK
Multi-Mode
Parallel Port
with
SERIAL
IRQ
Busy, Slct, PE,
ERROR, ACK
ChiProtectTM/FDC
MUX
Internal Bus
STROBE, INIT, SLCTIN,
ALF
LAD[3:0]
LFrame
(Data, Address, and Control lines)
(see LPC47B27x)
LPC
Bus Interface
LDRQ
PCI_RESET
LPCPD
TXD1, RXD1
CTS1, RTS1
DSR1, DTR1
DCD1, RI1
High-Speed
16550A
LPC47M14x
(128 QFP)
UART
IO_PME*
IO_SMI*
GP1[0:7]*
GP2[0:2,4:7]*
PORT 1
Power Mgmt
General
Purpose
I/O
TXD2 (IRTX)*,
RXD2 (IRRX)*
GP3[0:7]*, GP4[0:3]*
GP5[0:7]*, GP6[0:1]*
High-Speed
16550A
CTS2*, RTS2 *
DSR2*, DTR2*
DCD2*, RI2*
UART
PORT 2
ICLK
OCLK
CLOCK GEN
WDATA
MIDI_IN*
PD1+
PD1-
WCLOCK
MPU-401
Serial Port
MIDI_OUT*
PD2+
PD2-
DIGITAL DATA
SEPARATOR
WITH WRITE
PRECOM-
SMC PROPRIETARY
82077 COMPATIBLE
VERTICAL
KCLK, MCLK
PD3+
PD3-
PD4+
PD4-
FLOPPYDISK
PENSATION
KDATA, MDATA
GateA20*
CONTROLLER CORE
USB HUB
Keyboard/Mouse
8042
controller
KRESET*
P12*, P16*, P17*
RCLOCK
RDATA
PWROK[3,0]
PWREN[3,0]
Note 1: This diagram does not show power and ground
connections.
Note 2: Functions with "*" are located on multifunctional
pins. This diagram is designed to show the various functions
available on the chip (not pin layout).
FIGURE 1 – LPC47M14X BLOCK DIAGRAM
SMSC DS – LPC47M14X
Page 16
Rev. 03/19/2001
5
POWER FUNCTIONALITY
The LPC47M14x has three power planes: VCC, VTR, and VREF.
5.1 VCC POWER
The LPC47M14x is a 3.3 Volt part. The VCC supply is 3.3 Volts (nominal). See the “Operational Description” Section
and the “Maximum Current Values” subsection.
5.1.1
3 Volt Operation / 5 Volt Tolerance
The LPC47M14x is a 3.3 Volt part. It is intended solely for 3.3V applications. All signal pins are 5V tolerant except
those that pertain to the LPC Bus and USB Hub interfaces; that is, the input voltage is 5.5V max, and the I/O buffer
output pads are backdrive protected.
The LPC interface pins are 3.3 V only. These signals meet PCI DC specifications for 3.3V signaling. These pins are:
ꢀ
ꢀ
ꢀ
ꢀ
LAD[3:0]
LFRAME#
LDRQ#
LPCPD#
The USB interface pins are 3.3V tolerant. The maximum input voltage tolerated on the downstream port pins is 3.6V
(See “Operational Description” for the IOUSB buffers). These pins are labeled:
ꢀ
ꢀ
PD+[1:4]
PD-[1:4]
The input voltage for all other pins is 5.5V max including the following pins:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
PCI_RESET#
PCI_CLK
SER_IRQ
nIO_PME
nUSBOC[1:4]
nPWREN[1:4]
5.2 USB POWER
The LPC47M14x requires that the USB Hub maintain power for wake-up events in the absence of VCC power. To
meet these requirements, the Hub Block and the transceiver pins are powered by VTR. CLKI32, which is also
powered by VTR, is used to monitor changes in the signaling on the USB ports. This will enable the Hub Block to
resume from a suspend state by receiving a signal on either its downstream ports or its upstream port.
5.3 VTR SUPPORT
The LPC47M14x requires a trickle supply (VTR) to provide sleep current for the programmable wake-up events in the
PME interface when VCC is removed. The VTR pin is connected to the VTR (standby) power supply, which is 3.3
Volts (nominal). See the “Operational Description” Section. The maximum VTR current that is required depends on
the functions that are used in the part. See “Trickle Power Functionality” subsection and “Maximum Current Values”
subsection. This voltage source is also used to power the USB Hub interface, the IR interface, the PME configuration
registers, and the PME interface. The VTR pin generates a VTR Power-on-Reset signal to initialize these components.
Note: If VTR is to be used for programmable wake-up events when VCC is removed, VTR must be at its full
minimum potential at least 10 µs before Vcc begins a power-on cycle. When VTR and Vcc are fully
powered, the potential difference between the two supplies must not exceed 500mV.
5.4 VREF PIN
The LPC47M14x has a reference voltage pin input on pin 44 of the part. This reference voltage can be connected to
either a 5V supply or a 3.3V supply. It is used for the game port. See the “GAME PORT LOGIC” section.
SMSC DS – LPC47M14X
Page 17
Rev. 03/19/2001
5.5 INTERNAL PWRGOOD
An internal PWRGOOD logical control is included to minimize the effects of pin-state uncertainty in the host interface
as Vcc cycles on and off. When the internal PWRGOOD signal is “1” (active), Vcc > 2.3V (nominal), and the
LPC47M14x host interface is active. When the internal PWRGOOD signal is “0” (inactive), Vcc ≤ 2.3V (nominal), and
the LPC47M14x host interface is inactive; that is, LPC bus reads and writes will not be decoded.
The LPC47M14x device pins nIO_PME, CLOCKI32, KDAT, MDAT, IRRX, nRI1, nRI2, RXD2, USB+, USB-, PD[4:1]+,
PD[4:1]- and most GPIOs (as input) are part of the PME interface and remain active when the internal PWRGOOD
signal has gone inactive, since VTR must always be powered. The IRTX2/GP35, GP53/TXD2(IRTX), GP60/LED1 and
GP61/LED2 pins also remain active when the internal PWRGOOD signal has gone inactive. See “Trickle Power
Functionality” section. The internal PWRGOOD signal is also used to disable the IR Half Duplex Timeout.
5.6 32.768 KHZ TRICKLE CLOCK INPUT
The LPC47M14x utilizes a 32.768 kHz trickle input to supply a clock signal for the fan tachometer logic, LED blink,
wake on specific key function, and to the USB Hub to support suspend and resume signaling.
5.7 TRICKLE POWER FUNCTIONALITY
When the LPC47M14x is running under VTR only (VCC removed), PME wakeup events are active and (if enabled)
able to assert the nIO_PME pin active low. The following lists the wakeup events:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
UART 1 Ring Indicator
UART 2 Ring Indicator
Keyboard data
Mouse data
“Wake on Specific Key” Logic
Fan Tachometers (Note)
GPIOs for wakeup. See below.
Event on USB Downstream/Upstream ports
Note: The Fan Tachometers can generate a PME when VCC=0. Clear the enable bits for the fan
tachometers before removing fan power.
The following requirements apply to all I/O pins that are specified to be 5 volt tolerant:
ꢀ
I/O buffers that are wake-up event compatible are powered by VCC. Under VTR power (VCC=0), these pins may
only be configured as inputs. These pins have input buffers into the wakeup logic that are powered by VTR.
ꢀ
I/O buffers that may be configured as either push-pull or open drain under VTR power (VCC=0), are powered by
VTR. This means, at a minimum, they will source their specified current from VTR even when VCC is present.
The GPIOs that are used for PME wakeup as input are GP10-GP17, GP20-GP22, GP24-GP27, GP30-GP33, GP41,
GP43, GP50-GP57, GP60, and GP61. These GPIOs function as follows (with the exception of GP53, GP60 and
GP61 - see below):
ꢀ
Buffers are powered by VCC, but in the absence of VCC they are backdrive protected (they do not impose a load
on any external VTR powered circuitry). They are wakeup compatible as inputs under VTR power. These pins
have input buffers into the wakeup logic that are powered by VTR.
All GPIOs listed above are for PME wakeup as a GPIO (or alternate function). Note that GP32 and GP33 cannot be
used for wakeup under VTR power (VCC=0) since these are the fan control pins which come up as outputs and low
following a VCC POR and Hard Reset. GP53 cannot be used for wakeup under VTR power since this is the IRTX pin
which comes up as output and low following a VTR POR, a VCC POR and Hard Reset. Also, GP32 and GP33 revert
to their non-inverting GPIO input function when VCC is removed from the part. GP43 reverts to the basic GPIO
function when VCC is removed from the part, but its programmed input/output, invert/non-invert and output buffer
type is retained.
The other GPIOs function as follows:
GP36, GP37 and GP40:
ꢀ
Buffers are powered by VCC. In the absence of VCC they are backdrive protected. These pins do not have input
buffers into the wakeup logic that are powered by VTR, and are not used for wakeup.
SMSC DS – LPC47M14X
Page 18
Rev. 03/19/2001
GP35, GP42, GP53, GP60 and GP61:
ꢀ
Buffers powered by VTR. GP35 and GP53 have IRTX as the alternate function and their output buffers are
powered by VTR so that the pins are always forced low when not used. GP42 is the nIO_PME pin, which is
active under VTR. GP60 and GP61 have LED as the alternate function and the logic is able to control the pin
under VTR.
The IRTX pins (IRTX2/GP35 and GP53/TXD2(IRTX)) are powered by VTR so that they are driven low when VCC =
0V with VTR = 3.3V. These pins will remain low following a VCC POR until serial port 2 is enabled by setting the
activate bit, at which time the pin will reflect the state of the transmit output of the Serial Port 2 block.
The following list summarizes the blocks, registers and pins that are powered by VTR.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
USB Hub
PME interface block
PME runtime register block (includes all PME, SMI, GPIO, Fan and other miscellaneous registers)
“Wake on Specific Key” logic
LED control logic
Fan Tachometers
Pins for PME Wakeup:
◊
◊
◊
◊
◊
◊
◊
GP42/nIO_PME (output, buffer powered by VTR)
nRI1 (input)
GP50/nRI2 (input)
GP52/RXD2(IRRX) (input)
KDAT (input)
MDAT (input)
GPIOs (GP10-GP17, GP20-GP22, GP24-GP27, GP30-GP33, GP41, GP43, GP50-GP57, GP60, and
GP61) – all input-only except GP53, GP60, and GP61. See below.
ꢀ
Other Pins
◊
◊
◊
◊
IRTX2/GP35 (output, buffer powered by VTR)
GP53/TXD2(IRTX) (output, buffer powered by VTR)
GP60/LED1 (output, buffer powered by VTR)
GP61/LED2 (output, buffer powered by VTR)
5.8 MAXIMUM CURRENT VALUES
See the “Operational Description” section for the maximum current values.
The maximum VTR current, ITR, is given with all outputs open (not loaded), and all inputs in a fixed state (i.e., 0V or
3.3V). The total maximum current for the part is the unloaded value PLUS the maximum current sourced by all pins
that are driven by VTR. The pins that are powered by VTR are as follows: GP42/nIO_PME, IRTX2/GP35,
GP53/TXD2(IRTX), GP60/LED1, GP61/LED2, and CLKI32. These pins, if configured as push-pull outputs, will
source a minimum of 6mA at 2.4V when driving.
ꢀ
The maximum VCC current, ICC, is given with all outputs open (not loaded) , and all inputs in a fixed state
(i.e., 0V or 3.3V).
ꢀ
The maximum VREF current, IREF, is given with all outputs open (not loaded) , and all inputs in a fixed state
(i.e., 0V or 3.3V).
5.9 POWER MANAGEMENT EVENTS (PME/SCI)
The LPC47M14x offers support for Power Management Events (PMEs), also referred to as System Control Interrupt
(SCI) events. The terms PME and SCI are used synonymously throughout this document to refer to the indication of
an event to the chipset via the assertion of the nIO_PME output signal on pin 17. See the “PME Support” section.
SMSC DS – LPC47M14X
Page 19
Rev. 03/19/2001
6
FUNCTIONAL DESCRIPTION
6.1
SUPER I/O REGISTERS
The address map, shown below in Table 1 shows the addresses of the different blocks of the Super I/O immediately
after power up. The base addresses of the FDC, serial and parallel ports, PME register block, Game port and
configuration register block can be moved via the configuration registers. Some addresses are used to access more
than one register.
6.2 HOST PROCESSOR INTERFACE (LPC)
The host processor communicates with the LPC47M14x through a series of read/write registers via the LPC interface.
The port addresses for these registers are shown in Table 1. Register access is accomplished through I/O cycles or
DMA transfers. All registers are 8 bits wide.
Table 1 – Super I/O Block Addresses
LOGICAL
ADDRESS
BLOCK NAME
NOTES
DEVICE
Base+(0-5) and +(7)
Base+(0-7)
Floppy Disk
Serial Port Com 1
Serial Port Com 2
0
4
5
Base1+(0-7)
Base2+(0-7)
Parallel Port
SPP
3
Base+(0-3)
Base+(0-7)
EPP
Base+(0-3), +(400-402)
Base+(0-7), +(400-402)
60, 64
ECP
ECP+EPP+SPP
KYBD
7
9
A
B
Base + 0
Game Port
Runtime Registers
MPU-401
Configuration
USB Hub
Base + (0-5F)
Base + (0-1)
Base + (0-1)
n/a
2
1
C
Note: Refer to the configuration register descriptions for setting the base address.
Note 1: No Addressable Registers in the Hub Block.
Note 2: Logical Device A is referred to as the Runtime Register block or PME Block and may be
used interchangeably throughout this document.
SMSC DS – LPC47M14X
Page 20
Rev. 03/19/2001
6.3 LPC INTERFACE
The following sub-sections specify the implementation of the LPC bus.
6.3.1
LPC Interface Signal Definition
The signals required for the LPC bus interface are described in the table below. LPC bus signals use PCI 33MHz
electrical signal characteristics.
SIGNAL
TYPE
DESCRIPTION
NAME
LAD[3:0]
I/O
Input
Input
Output
OD
LPC address/data bus. Multiplexed command, address and data bus.
Frame signal. Indicates start of new cycle and termination of broken cycle
PCI Reset. Used as LPC Interface Reset.
Encoded DMA/Bus Master request for the LPC interface.
Power Mgt Event signal. Allows the LPC47M14x to request wakeup.
Powerdown Signal. Indicates that the LPC47M14x should prepare for power to be shut
on the LPC interface.
LFRAME#
PCI_RESET#
LDRQ#
nIO_PME
LPCPD#
Input
SER_IRQ
PCI_CLK
I/O
Input
Serial IRQ.
PCI Clock.
Note: The CLKRUN# signal is not implemented in this part.
6.3.2
LPC Cycles
The following cycle types are supported by the LPC protocol.
CYCLE TYPE
I/O Write
TRANSFER SIZE
1 Byte
I/O Read
1 Byte
DMA Write
DMA Read
1 byte
1 byte
The LPC47M14x ignores cycles that it does not support.
6.3.3
Field Definitions
The data transfers are based on specific fields that are used in various combinations, depending on the cycle type.
These fields are driven onto the LAD[3:0] signal lines to communicate address, control and data information over the
LPC bus between the host and the LPC47M14x. See the “Low Pin Count (LPC) Interface Specification”, Revision
1.0, Section 4.2 for definition of these fields.
6.3.4
LFRAME# Usage
LFRAME# is used by the host to indicate the start of cycles and the termination of cycles due to an abort or time-out
condition. This signal is to be used by the LPC47M14x to know when to monitor the bus for a cycle.
This signal is used as a general notification that the LAD[3:0] lines contain information relative to the start or stop of a
cycle, and that the LPC47M14x monitors the bus to determine whether the cycle is intended for it. The use of
LFRAME# allows the LPC47M14x to enter a lower power state internally. There is no need for the LPC47M14x to
monitor the bus when it is inactive, so it can decouple its state machines from the bus, and internally gate its clocks.
When the LPC47M14x samples LFRAME# active, it immediately stops driving the LAD[3:0] signal lines on the next
clock and monitor the bus for new cycle information.
The LFRAME# signal functions as described in the Low Pin Count (LPC) Interface Specification, Revision 1.0.
SMSC DS – LPC47M14X
Page 21
Rev. 03/19/2001
6.3.5
I/O Read and Write Cycles
The LPC47M14x is the target for I/O cycles. I/O cycles are initiated by the host for register or FIFO accesses, and
will generally have minimal Sync times. The minimum number of wait-states between bytes is 1. EPP cycles will
depend on the speed of the external device, and may have much longer Sync times.
Data transfers are assumed to be exactly 1-byte. If the CPU requested a 16 or 32-bit transfer, the host will break it
up into 8-bit transfers.
See the “Low Pin Count (LPC) Interface Specification” Revision 1.0, Section 5.2, for the sequence of cycles for the
I/O Read and Write cycles.
6.3.6
DMA Read and Write Cycles
DMA read cycles involve the transfer of data from the host (main memory) to the LPC47M14x. DMA write cycles
involve the transfer of data from the LPC47M14x to the host (main memory). Data will be coming from or going to a
FIFO and will have minimal Sync times. Data transfers to/from the LPC47B10x are 1, 2 or 4 bytes.
See the “Low Pin Count (LPC) Interface Specification” Revision 1.0, Section 6.4, for the field definitions and the
sequence of the DMA Read and Write cycles.
6.3.7
DMA Protocol
DMA on the LPC bus is handled through the use of the LDRQ# lines from the LPC47M14x and special encodings on
LAD[3:0] from the host.
The DMA mechanism for the LPC bus is described in the “Low Pin Count (LPC) Interface Specification,” Revision
1.0.
6.3.8
Power Management
CLOCKRUN Protocol
The CLKRUN# pin is not implemented in the LPC47M14x.
See the “Low Pin Count (LPC) Interface Specification” Revision 1.0, Section 8.1.
LPCPD Protocol
See the “Low Pin Count (LPC) Interface Specification” Revision 1.0, Section 8.2.
6.3.9
SYNC Protocol
See the “Low Pin Count (LPC) Interface Specification” Revision 1.0, Section 4.2.1.8 for a table of valid SYNC values.
Typical Usage
The SYNC pattern is used to add wait states. For read cycles, the LPC47M14x immediately drives the SYNC pattern
upon recognizing the cycle. The host immediately drives the sync pattern for write cycles. If the LPC47M14x needs
to assert wait states, it does so by driving 0101 or 0110 on LAD[3:0] until it is ready, at which point it will drive 0000 or
1001. The LPC47M14x will choose to assert 0101 or 0110, but not switch between the two patterns.
The data (or wait state SYNC) will immediately follow the 0000 or 1001 value. The SYNC value of 0101 is intended
to be used for normal wait states, wherein the cycle will complete within a few clocks. The LPC47M14x uses a SYNC
of 0101 for all wait states in a DMA transfer.
The SYNC value of 0110 is intended to be used where the number of wait states is large. This is provided for EPP
cycles, where the number of wait states could be quite large (>1 microsecond). However, the LPC47M14x uses a
SYNC of 0110 for all wait states in an I/O transfer.
The SYNC value is driven within 3 clocks.
SYNC Timeout
The SYNC value is driven within 3 clocks. If the host observes 3 consecutive clocks without a valid SYNC pattern, it
will abort the cycle.
The LPC47M14x does not assume any particular timeout. When the host is driving SYNC, it may have to insert a
very large number of wait states, depending on PCI latencies and retries.
SMSC DS – LPC47M14X
Page 22
Rev. 03/19/2001
SYNC Patterns and Maximum Number of SYNCS
If the SYNC pattern is 0101, then the host assumes that the maximum number of SYNCs is 8.
If the SYNC pattern is 0110, then no maximum number of SYNCs is assumed. The LPC47M14x has protection
mechanisms to complete the cycle. This is used for EPP data transfers and should utilize the same timeout
protection that is in EPP.
SYNC Error Indication
The LPC47M14x reports errors via the LAD[3:0] = 1010 SYNC encoding.
If the host was reading data from the LPC47M14x, data will still be transferred in the next two nibbles. This data may
be invalid, but it will be transferred by the LPC47M14x. If the host was writing data to the LPC47M14x, the data had
already been transferred.
In the case of multiple byte cycles, such as DMA cycles, an error SYNC terminates the cycle. Therefore, if the host is
transferring 4 bytes from a device, if the device returns the error SYNC in the first byte, the other three bytes will not
be transferred.
I/O and DMA START Fields
I/O and DMA cycles use a START field of 0000.
Reset Policy
The following rules govern the reset policy:
ꢀ
When PCI_RESET# goes inactive (high), the clock is assumed to have been running for 100usec prior to the
removal of the reset signal, so that everything is stable. This is the same reset active time after clock is stable
that is used for the PCI bus.
ꢀ
ꢀ
ꢀ
When PCI_RESET# goes active (low):
The host drives the LFRAME# signal high, tristates the LAD[3:0] signals, and ignores the LDRQ# signal.
The LPC47M14x must ignore LFRAME#, tristate the LAD[3:0] pins and drive the LDRQ# signal inactive (high).
6.3.10 LPC Transfer
Wait State Requirements
I/O Transfers
The LPC47M14x inserts three wait states for an I/O read and two wait states for an I/O write cycle. A SYNC of 0110
is used for all I/O transfers. The exception to this is for transfers where IOCHRDY would normally be deasserted in
an ISA transfer (i.e., EPP or IrCC transfers) in which case the sync pattern of 0110 is used and a large number of
syncs may be inserted (up to 330 which corresponds to a timeout of 10us).
DMA Transfers
The LPC47M14x inserts three wait states for a DMA read and four wait states for a DMA write cycle. A SYNC of
0101 is used for all DMA transfers.
See the example timing for the LPC cycles in the “Timing Diagrams” section.
SMSC DS – LPC47M14X
Page 23
Rev. 03/19/2001
6.4 USB HUB FUNCTIONAL DESCRIPTION
The USB Hub Block implements one upstream port and up to four downstream ports. The internal
address/data/control connection is provided for programming by BIOS the USB Vendor ID, Product ID, Device
Revision Number and number of down stream ports by accessing the Hub Control register. USB cable data is not
transmitted or received via the internal connection.
The USB Hub Block implements the requirements defined in the USB Hub Device Class Specification Version 1.1
(USB Specification 1.1, Chapter 11), including Status Change Endpoint, Hub class specific descriptors and Hub class
specific requests. The USB Hub Block supports Suspend and Resume both as a USB device and in terms of
propagating Suspend and Resume signaling. It also supports remote wakeup by a device on downstream ports.
For wakeup requirements, the Hub Block is powered from VTR. VTR also powers the 24MHz OSC/PLL, 32 KHz clock
input buffer, 48MHz CLK/OSC MUX and all Logical Device and Global Configuration Registers as well as
programmable wakeup events in the PME interface.
The Hub Block clock requirements are derived from separate CLK/OSC pins (ICLK, OCLK). Clock pins ICLK and
OCLK provide implementation flexibility for the system designer (see FIGURE 2). When a 48MHz clock signal is
available, it may be connected directly to the ICLK pin. To reduce overall system EMI, a local 24MHz oscillator may
alternately be connected between the ICLK and OCLK pins. The OSC_CLK control bit in the Logical Device C
Configuration Register at 0xF0, selects between clock sources. The 32 KHz clock source is used to time certain port
change events. This will ensure the USB Hub will respond to port change events while the hub is in Suspend.
Clocks for IO
Blocks
To Hub Block
and SIO
48 Mhz. (to
Hub Block)
OSC_CLK
(from config.
registers)
CLK/OSC
MUX
PLL_EN
(control
PLL
Buffer
OSC/PLL
from hub)
OCLK
ICLK
CLOCKI
CLKI32
14.318 MHz. 32.768 KHz.
24 MHz.
Crystal
Clock
Clock
48 MHz.
Clock
FIGURE 2 – LPC47M14X CLOCK GENERATOR
For power conservation the USB Hub Block turns off internal hub clocks during Suspend, as follows:
ꢀ
The Hub Block responds to two types of Suspend. Selective (or Port) Suspend and Global Suspend.
Segments of the bus can be selectively suspended by sending the command SetPortFeature
(PORT_SUSPEND) to the hub port to which that segment is attached. The suspended port will block activity
to the suspended bus segment. Because other ports on the hub remain active, internal clocks are not turned
off.
ꢀ
Global Suspend is used when no communication is desired anywhere on the bus and the entire bus is
placed in the Suspend state. The host signals the start of global suspend by ceasing all its transmissions
(including the SOF token). As the hub block, and each device on the bus, recognizes that the bus is in the
idle state for the appropriate length of time, it goes into the Suspend state. Because all bus segments
attached to the hub are in the Suspend state, the hub will turn off the internal 24MHz driven PLL. In addition,
48MHz is stopped in the Hub Block. The 48MHz clock signal at the ICLK pin, if enabled, is not stopped.
Control logic external to the LPC47M14X should stop this clock, if desired.
ꢀ
The Hub Block will Resume from a Suspend state by receiving any non-idle signaling by a remote wakeup
enabled device on its downstream ports or Resume signaling on its upstream port. If the Hub has been
enabled as a remote wakeup source, it will also Resume from connects and disconnects on downstream
SMSC DS – LPC47M14X
Page 24
Rev. 03/19/2001
ports. The internal 24MHz driven PLL (and the 48MHz in the Hub Block) will be started to complete the
Resume.
6.4.1
USB Downstream Port Selection
The LPC47M14x USB Hub has the ability to program, via BIOS, control register access or through external PIN
strapping options, the number of Down Stream Ports that are available to the User. There is also a “Pin Strapping”
option that will allow the board designer the ability to define the number of down stream ports that will be active via
during USB_PWR POR.
The LPC47M120 USB Hub block will make the following changes to its external signals and device class response
parameters:
1) All related input and output signals such as the associated Over-current sense pins (nUSBOC[x]) and Power
Enable (nPWREN[x]) pin are also disabled.
2) The USB Down Stream Port nUSBOC[x] input pin can be a NC (No Connect) pin or tied High (1). For EMI and
reduced Noise sensitivity, it is recommended that the pin be tied High (1).
3) The Power Enable (nPWREN[x]) pin will be forced low (0). For EMI and reduced Noise sensitivity, it is
recommended that the pin be tied High (1).
4) The associated PDx+ and PDx- pins will not be active can be a NC (No Connect) pin). For EMI and reduced
Noise sensitivity, it is recommended that the pin be tied High (1).
5) All Hub Device Class return descriptor must respond with the appropriate information relating to the number of
ports that are currently selected by the Strap Pins or control bits in the register described in Table 76
–
HubControl_1 Register Definition, shown on page 171, below, describes what fields now need to be
programmed bas on the number of enabled ports.
Table 2 – Hub Descriptor to be Modified
OFFSET
FIELD
bDescLength
PROGRAMMABLE
SIZE
1
DESCRIPTION
Number of bytes in this descriptor, including
0
this byte.
1
2
bDescriptorType
bNbrPorts
1
1
Descriptor Type
X
Number of downstream ports that this hub
supports. Selected by the “Strp0 and nStrp1”
input pins or the HubControl_1 register defined
in
Table 76
–
HubControl_1 Register
Definition, shown on page 171, below.
D1..D0: Power Switching Mode
3
wHubCharacteristics
2
00 - Ganged power switching (all ports’ power
at once)
01 - Individual port power switching
1X - No power switching (ports always powered
on when hub is on and off when hub is off).
D2:Identifies a Compound Device
0 - Hub is not part of a compound device
1 - Hub is part of a compound device
D4..D3: Over-current Protection Mode
00 - Global Over-current Protection. The hub
reports over-current as a summation of all
ports’ current draw, without a breakdown of
individual port over-current status.
01 - Individual Port Over-current protection.
The hub reports over-current on a per-port
basis. Each port has an over-current indicator.
1X -No Over-Current Protection. This option is
only allowed for bus-powered hubs that do not
implement over-current protection.
D15..D5: Reserved
SMSC DS – LPC47M14X
Page 25
Rev. 03/19/2001
OFFSET
FIELD
bPwrOn2PwrGood
PROGRAMMABLE
SIZE
1
DESCRIPTION
5
Time (in 2 ms intervals) from the time power on
sequence begins on a port until power is good
on that port. System software uses this value
to determine how long to wait before accessing
a powered-on port.
6
7
bHubContrCurrent
DeviceRemovable
1
Maximum current requirements of the hub
controller electronics in mA.
X
Variable
depending
on number
of ports on
hub
Indicates if a port has a removable device
attached.
If a non-removable device is
attached to a port, that port will never receive
an insertion change notification. This field is
reported on byte-granularity. Within a byte, if
no port exists for a given location, the field
representing the port characteristics returns “0”.
Bit definition:
0 - Device is removable
1 - Device is not removable (permanently
attached)
This is a bitmap corresponding to the individual
ports on the hub:
Bit 0: Reserved for future use
Bit 1: Port 1
Bit 2: Port 2
Etc.
Bit n: Port n (implementation dependent, up to
a maximum of 255 ports).
Variable PortPwrCtrlMask
X
Variable
depending
on number
of ports on
hub
Indicates if a port is not affected by a gang-
mode power control request. Ports that have
this field set always require
a
manual
SetPortFeature(PORT_POWER) request to
control the port’s power state.
Bit definition:
0 - Port does not mask the gang-mode power
control capability.
1 - Port is not affected by gang-mode power
commands. Manual commands must be sent
to this port to turn power on and off. This is a
bitmap corresponding to the individual ports on
the hub:
Bit 0: Reserved for future use.
Bit 1: Port 1
Bit 2: Port 2
Etc.
Bit n: Port n (implementation dependent, up to
a maximum of 255 ports).
6.5 FLOPPY DISK CONTROLLER
The Floppy Disk controller (FDC) provides the interface between a host microprocessor and the floppy disk drives.
The FDC integrates the functions of the Formatter/Controller, Digital data Separator, Write Precompensation and
Data Rate Selection logic for an IBM XT/AT compatible FDC. The true CMOS 765B core guarantees 100% IBM PC
XT/AT compatibility in addition to providing data overflow and underflow protection.
The FDC is compatible to the 82077AA using SMSC's proprietary floppy disk controller core.
SMSC DS – LPC47M14X
Page 26
Rev. 03/19/2001
6.5.1
FDC Internal Registers
The Floppy Disk Controller contains eight internal registers, which facilitate the interfacing between the host
microprocessor and the disk drive. Table 3 shows the addresses required to access these registers. Registers other
than the ones shown are not supported. The rest of the description assumes that the primary addresses have been
selected.
Table 3 – Status, Data and Control Registers
(Shown with base addresses of 3F0 and 370)
PRIMARY
ADDRESS
SECONDARY
R/W
REGISTER
ADDRESS
3F0
3F1
3F2
3F3
3F4
3F4
3F5
3F6
3F7
3F7
370
371
372
373
374
374
375
376
377
377
R
R
Status Register A (SRA)
Status Register B (SRB)
Digital Output Register (DOR)
Tape Drive Register (TSR)
Main Status Register (MSR)
Data Rate Select Register (DSR)
Data (FIFO)
R/W
R/W
R
W
R/W
Reserved
R
Digital Input Register (DIR)
Configuration Control Register (CCR)
W
STATUS REGISTER A (SRA)
Address 3F0 READ ONLY
This register is read-only and monitors the state of the internal interrupt signal and several disk interface pins in
PS/2 and Model 30 modes. The SRA can be accessed at any time when in PS/2 mode. In the PC/AT mode the data
bus pins D0 - D7 are held in a high impedance state for a read of address 3F0.
PS/2 Mode
7
6
5
4
3
2
1
nWP
0
DIR
INT
PENDIN
G
nDRV2
STEP
nTRK0
HDSEL
nINDX
RESET
COND.
0
1
0
N/A
0
N/A
N/A
0
BIT 0 DIRECTION
Active high status indicating the direction of head movement. A logic "1" indicates inward direction; a logic "0"
indicates outward direction.
BIT 1 nWRITE PROTECT
Active low status of the WRITE PROTECT disk interface input. A logic "0" indicates that the disk is write protected.
BIT 2 nINDEX
Active low status of the INDEX disk interface input.
BIT 3 HEAD SELECT
Active high status of the HDSEL disk interface input. A logic "1" selects side 1 and a logic "0" selects side 0.
BIT 4 nTRACK 0
Active low status of the TRK0 disk interface input.
BIT 5 STEP
Active high status of the STEP output disk interface output pin.
BIT 6 nDRV2
This function is not supported. This bit is always read as “1”.
BIT 7 INTERRUPT PENDING
Active high bit indicating the state of the Floppy Disk Interrupt output.
SMSC DS – LPC47M14X
Page 27
Rev. 03/19/2001
PS/2 Model 30 Mode
7
6
5
4
3
2
1
0
INT
DRQ STEP TRK0 nHDSEL INDX
WP
nDIR
PENDING
F/F
RESET
COND.
0
0
0
N/A
1
N/A
N/A
1
BIT 0 DIRECTION
Active low status indicating the direction of head movement. A logic "0" indicates inward direction; a logic "1"
indicates outward direction.
BIT 1 WRITE PROTECT
Active high status of the WRITE PROTECT disk interface input. A logic "1" indicates that the disk is write protected.
BIT 2 INDEX
Active high status of the INDEX disk interface input.
BIT 3 HEAD SELECT
Active low status of the HDSEL disk interface input. A logic "0" selects side 1 and a logic "1" selects side 0.
BIT 4 TRACK 0
Active high status of the TRK0 disk interface input.
BIT 5 STEP
Active high status of the latched STEP disk interface output pin. This bit is latched with the STEP output going active,
and is cleared with a read from the DIR register, or with a hardware or software reset.
BIT 6 DMA REQUEST
Active high status of the DMA request pending.
BIT 7 INTERRUPT PENDING
Active high bit indicating the state of the Floppy Disk Interrupt.
STATUS REGISTER B (SRB)
Address 3F1 READ ONLY
This register is read-only and monitors the state of several disk interface pins in PS/2 and Model 30 modes. The
SRB can be accessed at any time when in PS/2 mode. In the PC/AT mode the data bus pins D0 - D7 are held in a
high impedance state for a read of address 3F1.
PS/2 Mode
7
1
6
1
5
4
3
2
1
0
DRIVE WDATA RDATA WGATE MOT
MOT
SEL0 TOGGLE TOGGLE
EN1
0
EN0
RESET
COND.
1
1
0
0
0
0
0
BIT 0 MOTOR ENABLE 0
Active high status of the MTR0 disk interface output pin. This bit is low after a hardware reset and unaffected by a
software reset.
BIT 1 MOTOR ENABLE 1
Active high status of the MTR1 disk interface output pin. This bit is low after a hardware reset and unaffected by a
software reset.
BIT 2 WRITE GATE
Active high status of the WGATE disk interface output.
SMSC DS – LPC47M14X
Page 28
Rev. 03/19/2001
BIT 3 READ DATA TOGGLE
Every inactive edge of the RDATA input causes this bit to change state.
BIT 4 WRITE DATA TOGGLE
Every inactive edge of the WDATA input causes this bit to change state.
BIT 5 DRIVE SELECT 0
Reflects the status of the Drive Select 0 bit of the DOR (address 3F2 bit 0). This bit is cleared after a hardware reset
and it is unaffected by a software reset.
BIT 6 RESERVED
Always read as a logic "1".
BIT 7 RESERVED
Always read as a logic "1".
PS/2 Model 30 Mode
7
6
5
4
3
2
1
0
nDRV2 nDS1
nDS0 WDATA RDATA WGATE nDS3
nDS2
F/F
0
F/F
0
F/F
0
RESET
COND.
N/A
1
1
1
1
BIT 0 nDRIVE SELECT 2
The DS2 disk interface is not supported.
BIT 1 nDRIVE SELECT 3
The DS3 disk interface is not supported.
BIT 2 WRITE GATE
Active high status of the latched WGATE output signal. This bit is latched by the active going edge of WGATE and is
cleared by the read of the DIR register.
BIT 3 READ DATA
Active high status of the latched RDATA output signal. This bit is latched by the inactive going edge of RDATA and is
cleared by the read of the DIR register.
BIT 4 WRITE DATA
Active high status of the latched WDATA output signal. This bit is latched by the inactive going edge of WDATA and
is cleared by the read of the DIR register. This bit is not gated with WGATE.
BIT 5 nDRIVE SELECT 0
Active low status of the DS0 disk interface output.
BIT 6 nDRIVE SELECT 1
Active low status of the DS1 disk interface output.
BIT 7 nDRV2
Active low status of the DRV2 disk interface input. Note: This function is not supported.
DIGITAL OUTPUT REGISTER (DOR)
Address 3F2 READ/WRITE
The DOR controls the drive select and motor enables of the disk interface outputs. It also contains the enable for the
DMA logic and a software reset bit. The contents of the DOR are unaffected by a software reset. The DOR can be
written to at any time.
7
6
5
4
3
2
1
0
MOT
MOT
MOT
MOT
DMAEN
nRESET
DRIVE
DRIVE
EN3
EN2
EN1
EN0
SEL1
SEL0
RESET
COND.
0
0
0
0
0
0
0
0
SMSC DS – LPC47M14X
Page 29
Rev. 03/19/2001
BIT 0 and 1 DRIVE SELECT
These two bits are binary encoded for the drive selects, thereby allowing only one drive to be selected at one time.
BIT 2 nRESET
A logic "0" written to this bit resets the Floppy disk controller. This reset will remain active until a logic "1" is written to
this bit. This software reset does not affect the DSR and CCR registers, nor does it affect the other bits of the DOR
register. The minimum reset duration required is 100ns, therefore toggling this bit by consecutive writes to this
register is a valid method of issuing a software reset.
BIT 3 DMAEN
PC/AT and Model 30 Mode:
Writing this bit to logic "1" will enable the DMA and interrupt functions. This bit being a logic "0" will disable the DMA
and interrupt functions. This bit is a logic "0" after a reset and in these modes.
PS/2 Mode: In this mode the DMA and interrupt functions are always enabled. During a reset, this bit will be cleared
to a logic "0".
BIT 4 MOTOR ENABLE 0
This bit controls the MTR0 disk interface output. A logic "1" in this bit will cause the output pin to go active.
BIT 5 MOTOR ENABLE 1
This bit controls the MTR1 disk interface output. A logic "1" in this bit will cause the output pin to go active.
DRIVE
DOR VALUE
1CH
0
1
2DH
BIT 6 MOTOR ENABLE 2
The MTR2 disk interface output is not supported in the LPC47M14x.
BIT 7 MOTOR ENABLE 3
The MTR3 disk interface output is not supported in the LPC47M14x.
TAPE DRIVE REGISTER (TDR)
Address 3F3 READ/WRITE
The Tape Drive Register (TDR) is included for 82077 software compatibility and allows the user to assign tape
support to a particular drive during initialization. Any future references to that drive automatically invokes tape
support. The TDR Tape Select bits TDR.[1:0] determine the tape drive number. Table 4 illustrates the Tape Select Bit
encoding. Note that drive 0 is the boot device and cannot be assigned tape support. The remaining Tape Drive
Register bits TDR.[7:2] are tristated when read. The TDR is unaffected by a software reset.
Table 4 – Tape Select Bits
TAPE SEL1
TAPE SEL0
DRIVE
(TDR.1)
(TDR.0)
SELECTED
0
0
1
1
0
1
0
1
None
1
2
3
Table 5 – Internal 2 Drive Decode - Normal
DRIVE SELECT OUTPUTS
MOTOR ON OUTPUTS
(ACTIVE LOW)
DIGITAL OUTPUT REGISTER
(ACTIVE LOW)
nDS1 nDS0
Bit 7 Bit 6 Bit 5 Bit 4 Bit1 Bit 0
nMTR1
nBIT 5
nBIT 5
nBIT 5
nBIT 5
nBIT 5
nMTR0
nBIT 4
nBIT 4
nBIT 4
nBIT 4
nBIT 4
X
X
X
1
X
X
1
X
1
X
X
0
1
X
X
X
0
0
0
1
1
X
0
1
0
1
X
1
0
1
1
1
0
1
1
1
1
X
0
0
SMSC DS – LPC47M14X
Page 30
Rev. 03/19/2001
Table 6 – Internal 2 Drive Decode - Drives 0 and 1 Swapped
MOTOR ON OUTPUTS
(ACTIVE LOW)
DRIVE SELECT OUTPUTS
(ACTIVE LOW)
DIGITAL OUTPUT REGISTER
Bit 7 Bit 6 Bit 5 Bit 4 Bit1 Bit 0
nDS1
nDS0
nMTR1
nMTR0
nBIT 5
nBIT 5
nBIT 5
nBIT 5
nBIT 5
X
X
X
1
X
X
1
X
1
X
X
0
1
X
X
X
0
0
0
1
1
X
0
1
0
1
X
0
1
1
1
1
1
0
1
1
1
nBIT 4
nBIT 4
nBIT 4
nBIT 4
nBIT 4
X
0
0
Normal Floppy Mode
Normal mode. Register 3F3 contains only bits 0 and 1. When this register is read, bits 2 - 7 are ‘0’.
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
REG 3F3
0
0
0
0
0
0
tape sel1 tape sel0
Enhanced Floppy Mode 2 (OS2)
Register 3F3 for Enhanced Floppy Mode 2 operation.
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
REG 3F3 Reserved Reserved
Drive Type ID
Floppy Boot Drive
tape sel1 tape sel0
Table 7 – Drive Type ID
DIGITAL OUTPUT REGISTER REGISTER 3F3 - DRIVE TYPE ID
Bit 1
Bit 0
Bit 5
Bit 4
0
0
1
1
0
1
0
1
L0-CRF2 - B1
L0-CRF2 - B3
L0-CRF2 - B5
L0-CRF2 - B7
L0-CRF2 - B0
L0-CRF2 - B2
L0-CRF2 - B4
L0-CRF2 - B6
Note: L0-CRF2-Bx = Logical Device 0, Configuration Register F2, Bit x.
SMSC DS – LPC47M14X
Page 31
Rev. 03/19/2001
DATA RATE SELECT REGISTER (DSR)
Address 3F4 WRITE ONLY
This register is write only. It is used to program the data rate, amount of write precompensation, power down status, and
software reset. The data rate is programmed using the Configuration Control Register (CCR) not the DSR, for PC/AT
and PS/2 Model 30.
7
6
5
0
4
3
2
1
0
S/W
POWER
PRE-
PRE-
PRE-
DRATE DRATE
RESET DOWN
COMP2 COMP1 COMP0 SEL1
SEL0
0
RESET
COND.
0
0
0
0
0
0
1
This register is write only. It is used to program the data rate, amount of write precompensation, power down status, and
software reset. The data rate is programmed using the Configuration Control Register (CCR) not the DSR, for PC/AT
and PS/2 Model 30.
Other applications can set the data rate in the DSR. The data rate of the floppy controller is the most recent write of
either the DSR or CCR. The DSR is unaffected by a software reset. A hardware reset will set the DSR to 02H, which
corresponds to the default precompensation setting and 250 Kbps.
BIT 0 and 1 DATA RATE SELECT
These bits control the data rate of the floppy controller. See Table 9 for the settings corresponding to the individual data
rates. The data rate select bits are unaffected by a software reset, and are set to 250 Kbps after a hardware reset.
BIT 2 through 4 PRECOMPENSATION SELECT
These three bits select the value of write precompensation that will be applied to the WDATA output signal. Table 8
shows the precompensation values for the combination of these bits settings. Track 0 is the default starting track
number to start precompensation. this starting track number can be changed by the configure command.
Table 8 – Precompensation Delays
PRECOMP
432
PRECOMPENSATION
DELAY (nsec)
<2Mbps
2Mbps
111
001
010
011
100
101
110
000
0.00
0
41.67
20.8
41.7
62.5
83.3
104.2
125
83.34
125.00
166.67
208.33
250.00
Default
Default
Default: See Table 11
BIT 5 UNDEFINED
Should be written as a logic "0".
BIT 6 LOW POWER
A logic "1" written to this bit will put the floppy controller into manual low power mode. The floppy controller clock and
data separator circuits will be turned off. The controller will come out of manual low power mode after a software reset
or access to the Data Register or Main Status Register.
BIT 7 SOFTWARE RESET
This active high bit has the same function as the DOR RESET (DOR bit 2) except that this bit is self clearing.
Note: The DSR is Shadowed in the Floppy Data Rate Select Shadow Register, located at the offset 0x1F in the
runtime register block Separator circuits will be turned off. The controller will come out of manual low power.
SMSC DS – LPC47M14X
Page 32
Rev. 03/19/2001
Table 9 – Data Rates
DATA RATE DATA RATE
DRIVE RATE
DRATE(1)
DENSEL
DRT1
DRT0
SEL1
SEL0
MFM
FM
1
0
0
0
0
0
0
0
0
0
1
0
0
1
1
0
1
0
1Meg
500
300
---
1
1
0
0
1
0
0
1
1
0
1
0
250
150
125
250
0
0
0
0
1
1
1
1
1
0
0
1
1
0
1
0
1Meg
500
500
---
1
1
0
0
1
0
0
1
1
0
1
0
250
250
125
250
1
1
1
1
0
0
0
0
1
0
0
1
1
0
1
0
1Meg
500
2Meg
250
---
250
---
1
1
0
0
1
0
0
1
1
0
1
0
125
Drive Rate Table (Recommended) 00 = 360K, 1.2M, 720K, 1.44M and 2.88M Vertical Format
01 = 3-Mode Drive
10 = 2 Meg Tape
Note 1: The DRATE and DENSEL values are mapped onto the DRVDEN pins.
Table 10 – DRVDEN Mapping
DT1
0
DT0
0
DRVDEN1 (1)
DRVDEN0 (1)
DRIVE TYPE
4/2/1 MB 3.5"
2/1 MB 5.25" FDDS
DRATE0
DENSEL
2/1.6/1 MB 3.5" (3-MODE)
1
0
1
0
1
1
DRATE0
DRATE0
DRATE1
DRATE1
nDENSEL
DRATE0
PS/2
Table 11 – Default Precompensation Delays
PRECOMPENSATION
DATA RATE
DELAYS
2 Mbps
1 Mbps
20.8 ns
41.67 ns
125 ns
125 ns
125 ns
500 Kbps
300 Kbps
250 Kbps
SMSC DS – LPC47M14X
Page 33
Rev. 03/19/2001
MAIN STATUS REGISTER
Address 3F4 READ ONLY
The Main Status Register is a read-only register and indicates the status of the disk controller. The Main Status Register
can be read at any time. The MSR indicates when the disk controller is ready to receive data via the Data Register. It
should be read before each byte transferring to or from the data register except in DMA mode. No delay is required
when reading the MSR after a data transfer.
7
6
5
4
3
2
1
0
NON
DMA
CMD
DRV1
BUSY
DRV0
BUSY
BUSY
RQM
DIO
Reserved Reserved
BIT 0 - 1 DRV x BUSY
These bits are set to 1s when a drive is in the seek portion of a command, including implied and overlapped seeks and
recalibrates.
BIT 4 COMMAND BUSY
This bit is set to a 1 when a command is in progress. This bit will go active after the command byte has been accepted
and goes inactive at the end of the results phase. If there is no result phase (Seek, Recalibrate commands), this bit is
returned to a 0 after the last command byte.
BIT 5 NON-DMA
Reserved, read ‘0’. This part does not support non-DMA mode.
BIT 6 DIO
Indicates the direction of a data transfer once a RQM is set. A 1 indicates a read and a 0 indicates a write is required.
BIT 7 RQM
Indicates that the host can transfer data if set to a 1. No access is permitted if set to a 0.
DATA REGISTER (FIFO)
Address 3F5 READ/WRITE
All command parameter information, disk data and result status are transferred between the host processor and the
floppy disk controller through the Data Register.
Data transfers are governed by the RQM and DIO bits in the Main Status Register.
The Data Register defaults to FIFO disabled mode after any form of reset. This maintains PC/AT hardware
compatibility. The default values can be changed through the Configure command (enable full FIFO operation with
threshold control). The advantage of the FIFO is that it allows the system a larger DMA latency without causing a disk
error. Table 12 gives several examples of the delays with a FIFO.
The data is based upon the following formula:
Threshold # x
1
x 8
-
1.5 µs
=
DATA
RATE
DELAY
At the start of a command, the FIFO action is always disabled and command parameters must be sent based upon the
RQM and DIO bit settings. As the command execution phase is entered, the FIFO is cleared of any data to ensure that
invalid data is not transferred.
SMSC DS – LPC47M14X
Page 34
Rev. 03/19/2001
An overrun or underrun will terminate the current command and the transfer of data. Disk writes will complete the current
sector by generating a 00 pattern and valid CRC. Reads require the host to remove the remaining data so that the result
phase may be entered.
Table 12 – FIFO Service Delay
FIFO THRESHOLD
EXAMPLES
MAXIMUM DELAY TO SERVICING AT
2 Mbps DATA RATE
1 byte
2 bytes
8 bytes
15 bytes
1 x 4 µs - 1.5 µs = 2.5 µs
2 x 4 µs - 1.5 µs = 6.5 µs
8 x 4 µs - 1.5 µs = 30.5 µs
15 x 4 µs - 1.5 µs = 58.5 µs
FIFO THRESHOLD
EXAMPLES
MAXIMUM DELAY TO SERVICING AT
1 Mbps DATA RATE
1 byte
2 bytes
8 bytes
15 bytes
1 x 8 µs - 1.5 µs = 6.5 µs
2 x 8 µs - 1.5 µs = 14.5 µs
8 x 8 µs - 1.5 µs = 62.5 µs
15 x 8 µs - 1.5 µs = 118.5 µs
FIFO THRESHOLD
EXAMPLES
MAXIMUM DELAY TO SERVICING AT
500 Kbps DATA RATE
1 byte
2 bytes
8 bytes
15 bytes
1 x 16 µs - 1.5 µs = 14.5 µs
2 x 16 µs - 1.5 µs = 30.5 µs
8 x 16 µs - 1.5 µs = 126.5 µs
15 x 16 µs - 1.5 µs = 238.5 µs
DIGITAL INPUT REGISTER (DIR)
Address 3F7 READ ONLY
This register is read-only in all modes.
PC-AT Mode
7
6
0
5
0
4
0
3
0
2
0
1
0
0
0
DSK
CHG
RESET
COND.
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
BIT 0 - 6 UNDEFINED
The data bus outputs D0 - 6 are read as ‘0’.
BIT 7 DSKCHG
This bit monitors the pin of the same name and reflects the opposite value seen on the disk cable or the value
programmed in the Force Disk Change Register (see Runtime Register at offset 0x1E).
PS/2 Mode
7
6
1
5
1
4
1
3
1
2
1
0
DSK
DRATE DRATE nHIGH
CHG
SEL1
N/A
SEL0 DENS
N/A
RESET
COND.
N/A
N/A
N/A
N/A
N/A
1
SMSC DS – LPC47M14X
Page 35
Rev. 03/19/2001
BIT 0 nHIGH DENS
This bit is low whenever the 500 Kbps or 1 Mbps data rates are selected, and high when 250 Kbps and 300 Kbps are
selected.
BITS 1 - 2 DATA RATE SELECT
These bits control the data rate of the floppy controller. See Table 9 for the settings corresponding to the individual
data rates. The data rate select bits are unaffected by a software reset, and are set to 250 Kbps after a
hardware reset.
BITS 3 - 6 UNDEFINED
Always read as a logic "1"
BIT 7 DSKCHG
This bit monitors the pin of the same name and reflects the opposite value seen on the disk cable or the value
programmed in the Force Disk Change Register (see Runtime Register at offset 0x1E).
Model 30 Mode
7
6
0
5
0
4
0
3
2
1
0
DSK
DMAEN NOPREC DRATE DRATE
CHG
N/A
SEL1
1
SEL0
0
RESET
COND.
0
0
0
0
0
BITS 0 - 1 DATA RATE SELECT
These bits control the data rate of the floppy controller. See Table 9 for the settings corresponding to the individual data
rates. The data rate select bits are unaffected by a software reset, and are set to 250 Kbps after a hardware reset.
BIT 2 NOPREC
This bit reflects the value of NOPREC bit set in the CCR register.
BIT 3 DMAEN
This bit reflects the value of DMAEN bit set in the DOR register bit 3.
BITS 4 - 6 UNDEFINED
Always read as a logic "0"
BIT 7 DSKCHG
This bit monitors the pin of the same name and reflects the opposite value seen on the disk cable or the value
programmed in the Force Disk Change Register (see Runtime Register at offset 0x1E).
CONFIGURATION CONTROL REGISTER (CCR)
Address 3F7 WRITE ONLY
PC/AT and PS/2 Modes
7
6
5
4
3
2
1
0
DRATE DRATE
SEL1
1
SEL0
0
RESET
COND.
N/A
N/A
N/A
N/A
N/A
N/A
BIT 0 and 1 DATA RATE SELECT 0 and 1
These bits determine the data rate of the floppy controller. See Table 9 for the appropriate values.
SMSC DS – LPC47M14X
Page 36
Rev. 03/19/2001
BIT 2 - 7 RESERVED
Should be set to a logical "0"
PS/2 Model 30 Mode
7
6
5
4
3
2
1
0
NOPREC DRATE DRATE
SEL1
1
SEL0
0
RESET
COND.
N/A
N/A
N/A
N/A
N/A
N/A
BIT 0 and 1 DATA RATE SELECT 0 and 1
These bits determine the data rate of the floppy controller. See Table 9 for the appropriate values.
BIT 2 NO PRECOMPENSATION
This bit can be set by software, but it has no functionality. It can be read by bit 2 of the DSR when in Model 30 register
mode. Unaffected by software reset.
BIT 3 - 7 RESERVED
Should be set to a logical "0"
Table 10 shows the state of the DENSEL pin. The DENSEL pin is set high after a hardware reset and is unaffected by
the DOR and the DSR resets.
6.5.2
STATUS REGISTER ENCODING
During the Result Phase of certain commands, the Data Register contains data bytes that give the status of the
command just executed.
Table 13 – Status Register 0
BIT NO.
SYMBOL
NAME
DESCRIPTION
7,6
IC
Interrupt Code 00 - Normal termination of command. The specified
command was properly executed and completed without
error.
01 - Abnormal termination of command. Command
execution was started, but was not successfully
completed.
10 - Invalid command. The requested command could
not be executed.
11 - Abnormal termination caused by Polling.
5
4
SE
EC
Seek End
The FDC completed a Seek, Relative Seek or
Recalibrate command (used during a Sense Interrupt
Command).
Equipment
Check
The TRK0 pin failed to become a "1" after:
1. 80 step pulses in the Recalibrate command.
2. The Relative Seek command caused the FDC to
step outward beyond Track 0.
3
2
1,0
Unused. This bit is always "0".
Head Address The current head address.
Drive Select The current selected drive.
H
DS1,0
SMSC DS – LPC47M14X
Page 37
Rev. 03/19/2001
Table 14 – Status Register 1
NAME DESCRIPTION
BIT NO.
SYMBOL
7
EN
End of
The FDC tried to access a sector beyond the final sector
of the track (255D). Will be set if TC is not issued after
Read or Write Data command.
Cylinder
6
5
Unused. This bit is always "0".
DE
OR
Data Error
The FDC detected a CRC error in either the ID field or
the data field of a sector.
4
Overrun/
Underrun
Becomes set if the FDC does not receive CPU or DMA
service within the required time interval, resulting in data
overrun or underrun.
3
2
Unused. This bit is always "0".
Any one of the following:
ND
No Data
1. Read Data, Read Deleted Data command - the FDC
did not find the specified sector.
2. Read ID command - the FDC cannot read the ID field
without an error.
3. Read A Track command - the FDC cannot find the
proper sector sequence.
Not Writeable WP pin became a "1" while the FDC is executing a Write
Data, Write Deleted Data, or Format A Track command.
1
0
NW
MA
Missing
Any one of the following:
Address Mark
1. The FDC did not detect an ID address mark at the
specified track after encountering the index pulse
from the nINDEX pin twice.
2. The FDC cannot detect a data address mark or a
deleted data address mark on the specified track.
Table 15 – Status Register 2
NAME
Unused. This bit is always "0".
Control Mark Any one of the following:
BIT NO.
SYMBOL
DESCRIPTION
7
6
CM
Read Data command - the FDC encountered a deleted
data address mark.
Read Deleted Data command - the FDC encountered a
data address mark.
Data Error in The FDC detected a CRC error in the data field.
Data Field
5
4
DD
WC
Wrong
The track address from the sector ID field is different
Cylinder
from the track address maintained inside the FDC.
3
2
1
Unused. This bit is always "0".
Unused. This bit is always "0".
Bad Cylinder The track address from the sector ID field is different
from the track address maintained inside the FDC and is
equal to FF hex, which indicates a bad track with a hard
error according to the IBM soft-sectored format.
BC
0
MD
Missing Data The FDC cannot detect a data address mark or a
Address Mark deleted data address mark.
SMSC DS – LPC47M14X
Page 38
Rev. 03/19/2001
Table 16 – Status Register 3
NAME
BIT NO.
SYMBOL
DESCRIPTION
7
6
Unused. This bit is always "0".
WP
Write
Indicates the status of the WP pin.
Protected
5
4
3
Unused. This bit is always "1".
Indicates the status of the TRK0 pin.
Unused. This bit is always "1".
T0
Track 0
2
1,0
HD
DS1,0
Head Address Indicates the status of the HDSEL pin.
Drive Select Indicates the status of the DS1, DS0 pins.
RESET
There are three sources of system reset on the FDC: the PCI_RESET# pin, a reset generated via a bit in the DOR, and
a reset generated via a bit in the DSR. At power on, a Power On Reset initializes the FDC. All resets take the FDC out
of the power down state.
All operations are terminated upon a PCI_RESET#, and the FDC enters an idle state. A reset while a disk write is in
progress will corrupt the data and CRC.
On exiting the reset state, various internal registers are cleared, including the Configure command information, and the
FDC waits for a new command. Drive polling will start unless disabled by a new Configure command.
PCI_RESET# Pin (Hardware Reset)
The PCI_RESET# pin is a global reset and clears all registers except those programmed by the Specify command. The
DOR reset bit is enabled and must be cleared by the host to exit the reset state.
DOR Reset vs. DSR Reset (Software Reset)
These two resets are functionally the same. Both will reset the FDC core, which affects drive status information and the
FIFO circuits. The DSR reset clears itself automatically while the DOR reset requires the host to manually clear it. DOR
reset has precedence over the DSR reset. The DOR reset is set automatically upon a pin reset. The user must
manually clear this reset bit in the DOR to exit the reset state.
MODES OF OPERATION
The FDC has three modes of operation, PC/AT mode, PS/2 mode and Model 30 mode. These are determined by the
state of the Interface Mode bits in LD0-CRF0[3,2].
PC/AT mode
The PC/AT register set is enabled, the DMA enable bit of the DOR becomes valid (controls the interrupt and DMA
functions), and DENSEL is an active high signal.
PS/2 mode
This mode supports the PS/2 models 50/60/80 configuration and register set. The DMA bit of the DOR becomes a
"don't care". The DMA and interrupt functions are always enabled, and DENSEL is active low.
Model 30 mode
This mode supports PS/2 Model 30 configuration and register set. The DMA enable bit of the DOR becomes valid
(controls the interrupt and DMA functions), and DENSEL is active low.
DMA TRANSFERS
DMA transfers are enabled with the Specify command and are initiated by the FDC by activating a DMA request cycle.
DMA read, write and verify cycles are supported. The FDC supports two DMA transfer modes: Single Transfer and
Burst Transfer. Burst mode is enabled via Logical Device 0-CRF0-Bit[1] (LD0-CRF0[1]).
CONTROLLER PHASES
For simplicity, command handling in the FDC can be divided into three phases: Command, Execution, and Result. Each
phase is described in the following sections.
Command Phase
After a reset, the FDC enters the command phase and is ready to accept a command from the host. For each of the
commands, a defined set of command code bytes and parameter bytes has to be written to the FDC before the
SMSC DS – LPC47M14X
Page 39
Rev. 03/19/2001
command phase is complete. (Please refer to Table 17 for the command set descriptions). These bytes of data must be
transferred in the order prescribed.
Before writing to the FDC, the host must examine the RQM and DIO bits of the Main Status Register. RQM and DIO
must be equal to "1" and "0" respectively before command bytes may be written. RQM is set false by the FDC after
each write cycle until the received byte is processed. The FDC asserts RQM again to request each parameter byte of
the command unless an illegal command condition is detected. After the last parameter byte is received, RQM remains
"0" and the FDC automatically enters the next phase as defined by the command definition.
The FIFO is disabled during the command phase to provide for the proper handling of the "Invalid Command" condition.
Execution Phase
All data transfers to or from the FDC occur during the execution phase, which can proceed in DMA mode as indicated in
the Specify command.
After a reset, the FIFO is disabled. Each data byte is transferred by a read/write or DMA cycle depending on the DMA
mode. The Configure command can enable the FIFO and set the FIFO threshold value.
The following paragraphs detail the operation of the FIFO flow control. In these descriptions, <threshold> is defined as
the number of bytes available to the FDC when service is requested from the host and ranges from 1 to 16. The
parameter FIFOTHR, which the user programs, is one less and ranges from 0 to 15.
A low threshold value (i.e. 2) results in longer periods of time between service requests, but requires faster servicing of
the request for both read and write cases. The host reads (writes) from (to) the FIFO until empty (full), then the transfer
request goes inactive. The host must be very responsive to the service request. This is the desired case for use with a
"fast" system.
A high value of threshold (i.e. 12) is used with a "sluggish" system by affording a long latency period after a service
request, but results in more frequent service requests.
Non-DMA Mode - Transfers from the FIFO to the Host
This part does not support non-DMA mode.
Non-DMA Mode - Transfers from the Host to the FIFO
This part does not support non-DMA mode.
DMA Mode - Transfers from the FIFO to the Host
The FDC generates a DMA request cycle when the FIFO contains (16 - <threshold>) bytes, or the last byte of a full
sector transfer has been placed in the FIFO. The DMA controller must respond to the request by reading data from the
FIFO. The FDC will deactivate the DMA request when the FIFO becomes empty by generating the proper sync for the
data transfer.
DMA Mode - Transfers from the Host to the FIFO
The FDC generates a DMA request cycle when entering the execution phase of the data transfer commands. The DMA
controller must respond by placing data in the FIFO. The DMA request remains active until the FIFO becomes full. The
DMA request cycle is reasserted when the FIFO has <threshold> bytes remaining in the FIFO. The FDC will terminate
the DMA cycle after a TC, indicating that no more data is required.
Data Transfer Termination
The FDC supports terminal count explicitly through the TC pin and implicitly through the underrun/overrun and end-of-
track (EOT) functions. For full sector transfers, the EOT parameter can define the last sector to be transferred in a
single or multi-sector transfer.
If the last sector to be transferred is a partial sector, the host can stop transferring the data in mid-sector, and the FDC
will continue to complete the sector as if a TC cycle was received. The only difference between these implicit functions
and TC cycle is that they return "abnormal termination" result status. Such status indications can be ignored if they were
expected.
Note that when the host is sending data to the FIFO of the FDC, the internal sector count will be complete when the FDC
reads the last byte from its side of the FIFO. There may be a delay in the removal of the transfer request signal of up to
the time taken for the FDC to read the last 16 bytes from the FIFO. The host must tolerate this delay.
Result Phase
The generation of the interrupt determines the beginning of the result phase. For each of the commands, a defined set
of result bytes has to be read from the FDC before the result phase is complete. These bytes of data must be read out
for another command to start.
SMSC DS – LPC47M14X
Page 40
Rev. 03/19/2001
RQM and DIO must both equal "1" before the result bytes may be read. After all the result bytes have been read, the
RQM and DIO bits switch to "1" and "0" respectively, and the CB bit is cleared, indicating that the FDC is ready to accept
the next command.
Command Set/Descriptions
Commands can be written whenever the FDC is in the command phase. Each command has a unique set of needed
parameters and status results. The FDC checks to see that the first byte is a valid command and, if valid, proceeds
with the command. If it is invalid, an interrupt is issued. The user sends a Sense Interrupt Status command, which
returns an invalid command error. Refer to Table 17 for explanations of the various symbols used. Table 18 lists the
required parameters and the results associated with each command that the FDC is capable of performing.
Table 17 – Description of Command Symbols
SYMBOL
NAME
DESCRIPTION
C
D
Cylinder Address The currently selected address; 0 to 255.
Data Pattern
The pattern to be written in each sector data field during formatting.
D0, D1
Drive Select 0-1 Designates which drives are perpendicular drives on the
Perpendicular Mode Command. A "1" indicates a perpendicular
drive.
DIR
Direction Control If this bit is 0, then the head will step out from the spindle during a
relative seek. If set to a 1, the head will step in toward the spindle.
DS0, DS1
Disk Drive Select
DS1
DS0
DRIVE
Drive 0
Drive 1
0
0
0
1
DTL
Special Sector
Size
By setting N to zero (00), DTL may be used to control the number of
bytes transferred in disk read/write commands. The sector size (N =
0) is set to 128. If the actual sector (on the diskette) is larger than
DTL, the remainder of the actual sector is read but is not passed to
the host during read commands; during write commands, the
remainder of the actual sector is written with all zero bytes. The CRC
check code is calculated with the actual sector. When N is not zero,
DTL has no meaning and should be set to FF HEX.
EC
EFIFO
EIS
Enable Count
Enable FIFO
When this bit is "1" the "DTL" parameter of the Verify command
becomes SC (number of sectors per track).
This active low bit when a 0, enables the FIFO. A "1" disables the
FIFO (default).
When set, a seek operation will be performed before executing any
read or write command that requires the C parameter in the
command phase. A "0" disables the implied seek.
Enable Implied
Seek
EOT
GAP
GPL
End of Track
The final sector number of the current track.
Alters Gap 2 length when using Perpendicular Mode.
Gap Length
The Gap 3 size. (Gap 3 is the space between sectors excluding the
VCO synchronization field).
H/HDS
HLT
Head Address
Selected head: 0 or 1 (disk side 0 or 1) as encoded in the sector ID
field.
Head Load Time The time interval that FDC waits after loading the head and before
initializing a read or write operation. Refer to the Specify command
for actual delays.
HUT
Head Unload
The time interval from the end of the execution phase (of a read or
write command) until the head is unloaded. Refer to the Specify
command for actual delays.
Time
LOCK
Lock defines whether EFIFO, FIFOTHR, and PRETRK parameters of
the CONFIGURE COMMAND can be reset to their default values by
a "software Reset". (A reset caused by writing to the appropriate bits
of either the DSR or DOR)
MFM
MFM/FM Mode
Selector
A one selects the double density (MFM) mode. A zero selects single
density (FM) mode.
SMSC DS – LPC47M14X
Page 41
Rev. 03/19/2001
Table 17 – Description of Command Symbols
SYMBOL
NAME
DESCRIPTION
MT
Multi-Track
When set, this flag selects the multi-track operating mode. In this
mode, the FDC treats a complete cylinder under head 0 and 1 as a
single track. The FDC operates as this expanded track started at the
first sector under head 0 and ended at the last sector under head 1.
With this flag set, a multitrack read or write operation will
automatically continue to the first sector under head 1 when the FDC
finishes operating on the last sector under head 0.
Selector
N
Sector Size Code This specifies the number of bytes in a sector. If this parameter is
"00", then the sector size is 128 bytes. The number of bytes
transferred is determined by the DTL parameter. Otherwise the
sector size is (2 raised to the "Nth" power) times 128. All values up
to "07" hex are allowable. "07"h would equal a sector size of 16k. It
is the user's responsibility to not select combinations that are not
possible with the drive.
N SECTOR SIZE
128 Bytes
256 Bytes
512 Bytes
1024 Bytes
…
…
07 16K Bytes
NCN
ND
New Cylinder
Number
The desired cylinder number.
Non-DMA Mode Write ‘0’. This part does not support non-DMA mode.
Flag
OW
Overwrite
The bits D0-D3 of the Perpendicular Mode Command can only be
modified if OW is set to 1. OW id defined in the Lock command.
PCN
Present Cylinder The current position of the head at the completion of Sense Interrupt
Number
Status command.
POLL
PRETRK
Polling Disable
When set, the internal polling routine is disabled. When clear, polling
is enabled.
Precompensation Programmable from track 00 to FFH.
Start Track
Number
R
Sector Address The sector number to be read or written. In multi-sector transfers,
this parameter specifies the sector number of the first sector to be
read or written.
RCN
SC
Relative Cylinder Relative cylinder offset from present cylinder as used by the Relative
Number
Seek command.
Number of
The number of sectors per track to be initialized by the Format
Sectors Per Track command. The number of sectors per track to be verified during a
Verify command when EC is set.
SK
Skip Flag
When set to 1, sectors containing a deleted data address mark will
automatically be skipped during the execution of Read Data. If Read
Deleted is executed, only sectors with a deleted address mark will be
accessed. When set to "0", the sector is read or written the same as
the read and write commands.
SRT
Step Rate Interval The time interval between step pulses issued by the FDC.
Programmable from 0.5 to 8 milliseconds in increments of 0.5 ms at
the 1 Mbit data rate. Refer to the SPECIFY command for actual
delays.
ST0
ST1
ST2
ST3
Status 0
Status 1
Status 2
Status 3
Registers within the FDC that store status information after a
command has been executed. This status information is available to
the host during the result phase after command execution.
SMSC DS – LPC47M14X
Page 42
Rev. 03/19/2001
Table 17 – Description of Command Symbols
SYMBOL
WGATE
NAME
Write Gate
DESCRIPTION
Alters timing of WE to allow for pre-erase loads in perpendicular
drives.
6.5.3
Instruction Set
Table 18 – Instruction Set
READ DATA
DATA BUS
D5 D4 D3 D2 D1 D0
PHASE
Command
R/W D7
D6
REMARKS
Command Codes
W
W
W
MT MFM SK
0
0
0
0
0
1
1
0
0
0
HDS DS1 DS0
C
Sector ID information prior to
Command execution.
W
W
W
W
W
W
H
R
N
EOT
GPL
DTL
Execution
Result
Data transfer between the
FDD and system.
R
ST0
Status information after Com-
mand execution.
R
R
R
ST1
ST2
C
Sector ID information after
Command execution.
R
R
R
H
R
N
SMSC DS – LPC47M14X
Page 43
Rev. 03/19/2001
READ DELETED DATA
DATA BUS
D5 D4 D3 D2 D1 D0
PHASE
Command
R/W D7
D6
REMARKS
Command Codes
W
W
W
MT MFM SK
0
0
1
0
1
0
0
0
0
0
HDS DS1 DS0
C
Sector ID information prior to
Command execution.
W
W
W
W
W
W
H
R
N
EOT
GPL
DTL
Execution
Result
Data transfer between the
FDD and system.
R
ST0
Status information after Com-
mand execution.
R
R
R
ST1
ST2
C
Sector ID information after
Command execution.
R
R
R
H
R
N
WRITE DATA
DATA BUS
D5 D4 D3 D2 D1 D0
PHASE
R/W D7
D6
REMARKS
Command
W
W
W
MT MFM
0
0
0
0
0
0
1
0
1
Command Codes
0
0
HDS DS1 DS0
C
Sector ID information prior to
Command execution.
W
W
W
W
W
W
H
R
N
EOT
GPL
DTL
Execution
Result
Data transfer between the
FDD and system.
R
ST0
Status information after Com-
mand execution.
R
R
R
ST1
ST2
C
Sector ID information after
Command execution.
R
R
R
H
R
N
SMSC DS – LPC47M14X
Page 44
Rev. 03/19/2001
WRITE DELETED DATA
DATA BUS
PHASE
R/W D7
D6
D5 D4 D3
D2
D1
D0
REMARKS
Command
W
W
W
MT MFM
0
0
0
0
1
0
0
0
1
Command Codes
0
0
HDS DS1 DS0
C
Sector ID information prior
to Command execution.
W
W
W
W
W
W
H
R
N
EOT
GPL
DTL
Execution
Result
Data transfer between the
FDD and system.
R
ST0
Status information after
Command execution.
R
R
R
ST1
ST2
C
Sector ID information after
Command execution.
R
R
R
H
R
N
READ A TRACK
DATA BUS
PHASE
Command
R/W D7
D6
MFM
0
D5 D4 D3
D2
0
D1
1
D0
0
REMARKS
Command Codes
W
W
W
0
0
0
0
0
0
0
0
HDS DS1 DS0
C
Sector ID information prior
to Command execution.
W
W
W
W
W
W
H
R
N
EOT
GPL
DTL
Execution
Result
Data transfer between the
FDD and system. FDC
reads all of cylinders'
contents from index hole
to EOT.
R
ST0
Status information after
Command execution.
R
R
R
ST1
ST2
C
Sector ID information after
Command execution.
R
R
R
H
R
N
SMSC DS – LPC47M14X
Page 45
Rev. 03/19/2001
VERIFY
DATA BUS
D5 D4 D3
PHASE
R/W D7
D6
D2
D1
D0
REMARKS
Command
W
W
W
MT MFM SK
1
0
0
0
1
1
0
Command Codes
EC
0
0
HDS DS1 DS0
C
Sector ID information
prior
to
Command
execution.
W
W
W
W
W
W
H
R
N
EOT
GPL
DTL/SC
Execution
Result
No data transfer takes
place.
R
ST0
Status information after
Command execution.
R
R
R
ST1
ST2
C
Sector ID information
after
Command
execution.
R
R
R
H
R
N
VERSION
DATA BUS
D5 D4 D3
PHASE
Command
Result
R/W D7
D6
0
0
D2
0
0
D1
0
0
D0
0
0
REMARKS
Command Code
Enhanced Controller
W
R
0
1
0
0
1
1
0
0
SMSC DS – LPC47M14X
Page 46
Rev. 03/19/2001
FORMAT A TRACK
DATA BUS
PHASE
Command
R/W D7
D6
MFM
0
D5 D4 D3
D2
1
D1
0
D0
1
REMARKS
Command Codes
W
W
W
W
W
W
0
0
0
0
0
0
1
0
HDS DS1 DS0
N
Bytes/Sector
Sectors/Cylinder
Gap 3
SC
GPL
D
Filler Byte
Execution for
Each Sector
Repeat:
W
C
Input Sector Parameters
W
W
W
H
R
N
FDC formats an entire
cylinder
Result
R
ST0
Status information after
Command execution
R
R
R
R
R
R
ST1
ST2
Undefined
Undefined
Undefined
Undefined
RECALIBRATE
DATA BUS
R/W D7 D6 D5 D4 D3 D2
PHASE
D1
D0
REMARKS
Command
W
W
0
0
0
0
0
0
0
0
0
0
1
0
1
1
Command Codes
DS1 DS0
Execution
Head retracted to Track 0
Interrupt.
SENSE INTERRUPT STATUS
DATA BUS
R/W D7 D6 D5 D4 D3 D2 D1 D0
PHASE
Command
Result
REMARKS
Command Codes
W
R
0
0
0
0
1
0
0
0
ST0
Status information at the end
of each seek operation.
R
PCN
SPECIFY
DATA BUS
PHASE
R/W D7 D6 D5 D4 D3 D2 D1 D0
REMARKS
Command
W
W
W
0
0
0
0
0
0
1
HUT
1
Command Codes
SRT
HLT
ND
SMSC DS – LPC47M14X
Page 47
Rev. 03/19/2001
SENSE DRIVE STATUS
DATA BUS
PHASE
R/W D7 D6 D5 D4 D3
D2
D1
D0
REMARKS
Command
W
W
R
0
0
0
0
0
0
0
0
0
0
ST3
1
0
0
Command Codes
HDS DS1 DS0
Result
Status information about
FDD
SEEK
DATA BUS
R/W D7 D6 D5 D4 D3
PHASE
Command
D2
1
D1
1
D0
1
REMARKS
Command Codes
W
W
W
0
0
0
0
0
0
0
0
1
0
NCN
HDS DS1 DS0
Execution
Head positioned over
proper
cylinder
on
diskette.
CONFIGURE
DATA BUS
PHASE
R/W D7 D6
D5
D4
D3
D2
D1
D0
REMARKS
Command
W
0
0
0
1
0
0
1
1
Configure
Information
W
W
W
0
0
0
0
0
0
0
0
0
EIS EFIFO POLL
FIFOTHR
Execution
PRETRK
RELATIVE SEEK
DATA BUS
PHASE
R/W D7 D6 D5 D4 D3
D2
D1
D0
REMARKS
Command
W
W
W
1
0
DIR
0
0
0
0
0
1
0
RCN
1
1
1
HDS DS1 DS0
DUMPREG
DATA BUS
PHASE
Command
R/W
W
REMARKS
D7
0
D6
0
D5
0
D4
0
D3 D2
D1
1
D0
0
1
1
*Note:
Registers
placed in
FIFO
Execution
Result
R
R
R
R
R
R
R
R
R
R
PCN-Drive 0
PCN-Drive 1
PCN-Drive 2
PCN-Drive 3
SRT
HUT
GAP
HLT
SC/EOT
D2 D1 D0
EIS EFIFO POLL
PRETRK
ND
LOCK
0
0
D3
WGATE
FIFOTHR
SMSC DS – LPC47M14X
Page 48
Rev. 03/19/2001
READ ID
DATA BUS
D5 D4 D3
PHASE
Command
R/W D7
D6
MFM
0
D2
0
D1
1
D0
0
REMARKS
Commands
W
W
0
0
0
0
0
0
1
0
HDS DS1 DS0
Execution
Result
The first correct ID
information
on
the
Cylinder is stored in
Data Register
R
ST0
Status information after
Command execution.
Disk status after the
Command has
completed
R
R
R
R
R
R
ST1
ST2
C
H
R
N
PERPENDICULAR MODE
DATA BUS
PHASE
Command
R/W
W
D7
0
OW
D6 D5 D4 D3 D2
D1
1
D0
0
WGATE
REMARKS
Command Codes
0
0
0
1
0
0
D3 D2 D1 D0
GAP
INVALID CODES
DATA BUS
R/W D7 D6 D5 D4 D3 D2 D1 D0
PHASE
REMARKS
Command
W
Invalid Codes
Invalid
Command
Codes
(NoOp - FDC goes into Stand-
by State)
Result
R
ST0
ST0 = 80H
LOCK
DATA BUS
PHASE
Command
Result
R/W
W
R
D7
LOCK
0
D6 D5
D4
1
LOCK
D3 D2 D1 D0
REMARKS
Command Codes
0
0
0
0
0
0
1
0
0
0
0
0
SC is returned if the last command that was issued was the Format command. EOT is returned if the last command was
a Read or Write.
Note: These bits are used internally only. They are not reflected in the Drive Select pins. It is the user's
responsibility to maintain correspondence between these bits and the Drive Select pins (DOR).
SMSC DS – LPC47M14X
Page 49
Rev. 03/19/2001
6.5.4
DATA TRANSFER COMMANDS
All of the Read Data, Write Data and Verify type commands use the same parameter bytes and return the same results
information, the only difference being the coding of bits 0-4 in the first byte.
An implied seek will be executed if the feature was enabled by the Configure command. This seek is completely
transparent to the user. The Drive Busy bit for the drive will go active in the Main Status Register during the seek portion
of the command. If the seek portion fails, it is reflected in the results status normally returned for a Read/Write Data
command. Status Register 0 (ST0) would contain the error code and C would contain the cylinder on which the seek
failed.
Read Data
A set of nine (9) bytes is required to place the FDC in the Read Data Mode. After the Read Data command has been
issued, the FDC loads the head (if it is in the unloaded state), waits the specified head settling time (defined in the
Specify command), and begins reading ID Address Marks and ID fields. When the sector address read off the diskette
matches with the sector address specified in the command, the FDC reads the sector's data field and transfers the data
to the FIFO.
After completion of the read operation from the current sector, the sector address is incremented by one and the data
from the next logical sector is read and output via the FIFO. This continuous read function is called "Multi-Sector Read
Operation". Upon receipt of the TC cycle, or an implied TC (FIFO overrun/underrun), the FDC stops sending data but
will continue to read data from the current sector, check the CRC bytes, and at the end of the sector, terminate the Read
Data Command.
N determines the number of bytes per sector (see Table 19 below). If N is set to zero, the sector size is set to 128. The
DTL value determines the number of bytes to be transferred. If DTL is less than 128, the FDC transfers the specified
number of bytes to the host. For reads, it continues to read the entire 128-byte sector and checks for CRC errors. For
writes, it completes the 128-byte sector by filling in zeros. If N is not set to 00 Hex, DTL should be set to FF Hex and
has no impact on the number of bytes transferred.
Table 19 – Sector Sizes
N
SECTOR SIZE
00
01
02
03
..
128 bytes
256 bytes
512 bytes
1024 bytes
...
07
16 Kbytes
The amount of data, which can be handled with a single command to the FDC, depends upon MT (multi-track) and N
(number of bytes/sector).
The Multi-Track function (MT) allows the FDC to read data from both sides of the diskette. For a particular cylinder, data
will be transferred starting at Sector 1, Side 0 and completing the last sector of the same track at Side 1.
If the host terminates a read or write operation in the FDC, the ID information in the result phase is dependent upon the
state of the MT bit and EOT byte. Refer to Table 20.
At the completion of the Read Data command, the head is not unloaded until after the Head Unload Time Interval
(specified in the Specify command) has elapsed. If the host issues another command before the head unloads, then
the head settling time may be saved between subsequent reads.
If the FDC detects a pulse on the nINDEX pin twice without finding the specified sector (meaning that the diskette's
index hole passes through index detect logic in the drive twice), the FDC sets the IC code in Status Register 0 to "01"
indicating abnormal termination, sets the ND bit in Status Register 1 to "1" indicating a sector not found, and terminates
the Read Data Command.
After reading the ID and Data Fields in each sector, the FDC checks the CRC bytes. If a CRC error occurs in the ID or
data field, the FDC sets the IC code in Status Register 0 to "01" indicating abnormal termination, sets the DE bit flag in
Status Register 1 to "1", sets the DD bit in Status Register 2 to "1" if CRC is incorrect in the ID field, and terminates the
Read Data Command. Table 21 describes the effect of the SK bit on the Read Data command execution and results.
Except where noted in Table 21, the C or R value of the sector address is automatically incremented (see Table 23).
SMSC DS – LPC47M14X
Page 50
Rev. 03/19/2001
Table 20 – Effects of MT and N Bits
MAXIMUM TRANSFER
CAPACITY
FINAL SECTOR READ
FROM DISK
26 at side 0 or 1
26 at side 1
15 at side 0 or 1
15 at side 1
8 at side 0 or 1
16 at side 1
MT
0
N
1
1
2
2
3
3
256 x 26 = 6,656
256 x 52 = 13,312
512 x 15 = 7,680
512 x 30 = 15,360
1024 x 8 = 8,192
1024 x 16 = 16,384
1
0
1
0
1
Table 21 – Skip Bit vs Read Data Command
DATA ADDRESS
MARK TYPE
RESULTS
SK BIT
SECTOR CM BIT OF DESCRIPTION OF
ENCOUNTERED
VALUE
READ?
ST2 SET?
RESULTS
0
Normal Data
Deleted Data
Yes
No
Normal
termination.
Address not
0
Yes
Yes
incremented. Next
sector not
searched for.
Normal
1
1
Normal Data
Deleted Data
Yes
No
No
termination.
Normal
Yes
termination.
Sector not read
("skipped").
Read Deleted Data
This command is the same as the Read Data command, only it operates on sectors that contain a Deleted Data Address
Mark at the beginning of a Data Field.
Table 22 describes the effect of the SK bit on the Read Deleted Data command execution and results. Except where
noted in Table 22, the C or R value of the sector address is automatically incremented (see
Table 23).
Table 22 – Skip Bit vs. Read Deleted Data Command
RESULTS
DATA ADDRESS
MARK TYPE
SK BIT
VALUE
SECTOR CM BIT OF DESCRIPTION OF
ENCOUNTERED
READ?
ST2 SET?
RESULTS
0
Normal Data
Yes
Yes
Address not
incremented. Next
sector not
searched for.
Normal
0
1
Deleted Data
Normal Data
Yes
No
No
termination.
Normal
Yes
termination.
Sector not read
("skipped").
Normal
termination.
1
Deleted Data
Yes
No
SMSC DS – LPC47M14X
Page 51
Rev. 03/19/2001
Read A Track
This command is similar to the Read Data command except that the entire data field is read continuously from each of
the sectors of a track. Immediately after encountering a pulse on the nINDEX pin, the FDC starts to read all data fields
on the track as continuous blocks of data without regard to logical sector numbers. If the FDC finds an error in the ID or
DATA CRC check bytes, it continues to read data from the track and sets the appropriate error bits at the end of the
command. The FDC compares the ID information read from each sector with the specified value in the command and
sets the ND flag of Status Register 1 to a “1” if there no comparison. Multi-track or skip operations are not allowed with
this command. The MT and SK bits (bits D7 and D5 of the first command byte respectively) should always be set to "0".
This command terminates when the EOT specified number of sectors has not been read. If the FDC does not find an ID
Address Mark on the diskette after the second occurrence of a pulse on the INDEX pin, then it sets the IC code in Status
Register 0 to "01" (abnormal termination), sets the MA bit in Status Register 1 to "1", and terminates the command.
Table 23 – Result Phase Table
FINAL SECTOR
ID INFORMATION AT RESULT PHASE
MT
HEAD
TRANSFERRED TO
HOST
C
H
R
N
Less than EOT
Equal to EOT
Less than EOT
Equal to EOT
Less than EOT
Equal to EOT
Less than EOT
Equal to EOT
NC
C + 1
NC
C + 1
NC
NC
NC
NC
NC
NC
NC
LSB
NC
LSB
R + 1
01
R + 1
01
R + 1
01
R + 1
01
NC
NC
NC
NC
NC
NC
NC
NC
0
0
1
0
1
1
NC
C + 1
NC: No Change, the same value as the one at the beginning of command execution.
LSB: Least Significant Bit, the LSB of H is complemented.
Write Data
After the Write Data command has been issued, the FDC loads the head (if it is in the unloaded state), waits the
specified head load time if unloaded (defined in the Specify command), and begins reading ID fields. When the sector
address read from the diskette matches the sector address specified in the command, the FDC reads the data from the
host via the FIFO and writes it to the sector's data field.
After writing data into the current sector, the FDC computes the CRC value and writes it into the CRC field at the end of
the sector transfer. The Sector Number stored in "R" is incremented by one, and the FDC continues writing to the next
data field. The FDC continues this "Multi-Sector Write Operation". Upon receipt of a terminal count signal or if a FIFO
over/under run occurs while a data field is being written, then the remainder of the data field is filled with zeros. The
FDC reads the ID field of each sector and checks the CRC bytes. If it detects a CRC error in one of the ID fields, it sets
the IC code in Status Register 0 to "01" (abnormal termination), sets the DE bit of Status Register 1 to "1", and
terminates the Write Data command.
The Write Data command operates in much the same manner as the Read Data command. The following items are the
same. Please refer to the Read Data Command for details:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Transfer Capacity
EN (End of Cylinder) bit
ND (No Data) bit
Head Load, Unload Time Interval
ID information when the host terminates the command
Definition of DTL when N = 0 and when N does not = 0
Write Deleted Data
This command is almost the same as the Write Data command except that a Deleted Data Address Mark is written at
the beginning of the Data Field instead of the normal Data Address Mark. This command is typically used to mark a bad
sector containing an error on the floppy disk.
SMSC DS – LPC47M14X
Page 52
Rev. 03/19/2001
Verify
The Verify command is used to verify the data stored on a disk. This command acts exactly like a Read Data command
except that no data is transferred to the host. Data is read from the disk and CRC is computed and checked against the
previously-stored value.
Because data is not transferred to the host, the TC cycle cannot be used to terminate this command. By setting the EC
bit to "1", an implicit TC will be issued to the FDC. This implicit TC will occur when the SC value has decremented
to 0 (an SC value of 0 will verify 256 sectors). This command can also be terminated by setting the EC bit to "0" and the
EOT value equal to the final sector to be checked. If EC is set to "0", DTL/SC should be programmed to 0FFH. Refer to
Table 23 and Table 24 for information concerning the values of MT and EC versus SC and EOT value.
Definitions:
# Sectors Per Side = Number of formatted sectors per each side of the disk.
# Sectors Remaining = Number of formatted sectors left which can be read, including side 1 of the disk if MT is set to
"1".
Table 24 – Verify Command Result Phase Table
MT
EC
SC/EOT VALUE
TERMINATION RESULT
Success Termination
Result Phase Valid
SC = DTL
0
0
EOT ≤ # Sectors Per Side
SC = DTL
EOT > # Sectors Per Side
SC ≤ # Sectors Remaining AND
EOT ≤ # Sectors Per Side
SC > # Sectors Remaining OR
EOT > # Sectors Per Side
SC = DTL
Unsuccessful Termination
Result Phase Invalid
Successful Termination
Result Phase Valid
Unsuccessful Termination
Result Phase Invalid
Successful Termination
Result Phase Valid
Unsuccessful Termination
Result Phase Invalid
Successful Termination
Result Phase Valid
Unsuccessful Termination
Result Phase Invalid
0
0
0
1
1
1
1
0
1
1
0
0
1
1
EOT ≤ # Sectors Per Side
SC = DTL
EOT > # Sectors Per Side
SC ≤ # Sectors Remaining AND
EOT ≤ # Sectors Per Side
SC > # Sectors Remaining OR
EOT > # Sectors Per Side
Note: If MT is set to "1" and the SC value is greater than the number of remaining formatted sectors
on Side 0, verifying will continue on Side 1 of the disk.
SMSC DS – LPC47M14X
Page 53
Rev. 05/02/2000
Format A Track
The Format command allows an entire track to be formatted. After a pulse from the nINDEX pin is detected, the FDC
starts writing data on the disk including gaps, address marks, ID fields, and data fields per the IBM System 34 or 3740
format (MFM or FM respectively). The particular values that will be written to the gap and data field are controlled by the
values programmed into N, SC, GPL, and D which are specified by the host during the command phase. The data field
of the sector is filled with the data byte specified by D. The ID field for each sector is supplied by the host; that is, four
data bytes per sector are needed by the FDC for C, H, R, and N (cylinder, head, sector number and sector size
respectively).
After formatting each sector, the host must send new values for C, H, R and N to the FDC for the next sector on the
track. The R value (sector number) is the only value that must be changed by the host after each sector is formatted.
This allows the disk to be formatted with nonsequential sector addresses (interleaving). This incrementing and
formatting continues for the whole track until the FDC encounters a pulse on the nINDEX pin again and it terminates the
command.
Table 25 contains typical values for gap fields that are dependent upon the size of the sector and the number of sectors
on each track. Actual values can vary due to drive electronics.
FORMAT FIELDS
SYSTEM 34 (DOUBLE DENSITY) FORMAT
DATA
GAP4a SYNC
IAM
GAP1 SYNC IDAM
C
Y
L
H
D
S
E
C
N
O
C
R
C
GAP2 SYNC
AM
C
R
C
80x
4E
12x
00
50x
4E
12x
00
22x
4E
12x
00
DATA
DATA
DATA
GAP3 GAP 4b
GAP3 GAP 4b
GAP3 GAP 4b
3x FC
C2
3x FE
A1
3x FB
A1 F8
SYSTEM 3740 (SINGLE DENSITY) FORMAT
DATA
GAP4a SYNC
IAM
FC
GAP1 SYNC IDAM
C
Y
L
H
D
S
E
C
N
O
C
R
C
GAP2 SYNC
AM
C
R
C
40x
FF
6x
00
26x
FF
6x
00
11x
FF
6x
00
FE
FB or
F8
PERPENDICULAR FORMAT
DATA
AM
GAP4a SYNC
IAM
GAP1 SYNC IDAM
C
Y
L
H
D
S
E
C
N
O
C
R
C
GAP2 SYNC
C
R
C
80x
4E
12x
00
50x
4E
12x
00
41x
4E
12x
00
3x FC
C2
3x FE
A1
3x FB
A1 F8
SMSC DS – LPC47M14X
Page 54
Rev. 05/02/2000
Table 25 – Typical Values for Formatting
FORMAT SECTOR SIZE
N
SC GPL1 GPL2
128
128
512
00 12
00 10
02 08
03 04
04 02
05 01
...
07
10
18
46
C8
C8
09
19
30
87
FF
FF
FM
1024
2048
4096
...
5.25" Drives
256
256
01 12
01 10
02 09
03 04
04 02
05 01
...
0A
20
2A
80
C8
C8
0C
32
50
F0
FF
FF
512*
1024
2048
4096
...
MFM
128
256
512
0
1
2
0F
09
05
07
0F
1B
1B
2A
3A
3.5" Drives
FM
256
512**
1024
1
2
3
0F
09
05
0E
1B
35
36
54
74
MFM
GPL1 = suggested GPL values in Read and Write commands to avoid splice point between data field and
ID field of contiguous sections.
GPL2 = suggested GPL value in Format A Track command.
*PC/AT values (typical)
**PS/2 values (typical). Applies with 1.0 MB and 2.0 MB drives.
Note: All values except sector size are in hex.
CONTROL COMMANDS
Control commands differ from the other commands in that no data transfer takes place. Three commands generate an
interrupt when complete: Read ID, Recalibrate, and Seek. The other control commands do not generate an interrupt.
Read ID
The Read ID command is used to find the present position of the recording heads. The FDC stores the values from the
first ID field it is able to read into its registers. If the FDC does not find an ID address mark on the diskette after the
second occurrence of a pulse on the nINDEX pin, it then sets the IC code in Status Register 0 to "01" (abnormal
termination), sets the MA bit in Status Register 1 to "1", and terminates the command.
The following commands will generate an interrupt upon completion. They do not return any result bytes. It is highly
recommended that control commands be followed by the Sense Interrupt Status command. Otherwise, valuable
interrupt status information will be lost.
Recalibrate
This command causes the read/write head within the FDC to retract to the track 0 position. The FDC clears the contents
of the PCN counter and checks the status of the nTRK0 pin from the FDD. As long as the nTRK0 pin is low, the DIR pin
remains 0 and step pulses are issued. When the nTRK0 pin goes high, the SE bit in Status Register 0 is set to "1" and
the command is terminated. If the nTRK0 pin is still low after 79 step pulses have been issued, the FDC sets the SE and
the EC bits of Status Register 0 to "1" and terminates the command. Disks capable of handling more than 80 tracks per
side may require more than one Recalibrate command to return the head back to physical Track 0.
The Recalibrate command does not have a result phase. The Sense Interrupt Status command must be issued after the
Recalibrate command to effectively terminate it and to provide verification of the head position (PCN). During the
command phase of the recalibrate operation, the FDC is in the BUSY state, but during the execution phase it is in a
NON-BUSY state. At this time, another Recalibrate command may be issued, and in this manner parallel Recalibrate
operations may be done on up to four drives at once. Upon power up, the software must issue a Recalibrate command
to properly initialize all drives and the controller.
SMSC DS – LPC47M14X
Page 55
Rev. 05/02/2000
Seek
The read/write head within the drive is moved from track to track under the control of the Seek command. The FDC
compares the PCN, which is the current head position, with the NCN and performs the following operation if there is a
difference:
PCN < NCN: Direction signal to drive set to "1" (step in) and issues step pulses.
PCN > NCN: Direction signal to drive set to "0" (step out) and issues step pulses.
The rate at which step pulses are issued is controlled by SRT (Stepping Rate Time) in the Specify command. After each
step pulse is issued, NCN is compared against PCN, and when NCN = PCN the SE bit in Status Register 0 is set to "1"
and the command is terminated. During the command phase of the seek or recalibrate operation, the FDC is in the
BUSY state, but during the execution phase it is in the NON-BUSY state. At this time, another Seek or Recalibrate
command may be issued, and in this manner, parallel seek operations may be done on up to four drives at once.
Note that if implied seek is not enabled, the read and write commands should be preceded by:
1) Seek command - Step to the proper track
2) Sense Interrupt Status command - Terminate the Seek command
3) Read ID - Verify head is on proper track
4) Issue Read/Write command.
The Seek command does not have a result phase. Therefore, it is highly recommended that the Sense Interrupt Status
command is issued after the Seek command to terminate it and to provide verification of the head position (PCN). The
H bit (Head Address) in ST0 will always return to a "0". When exiting POWERDOWN mode, the FDC clears the PCN
value and the status information to zero. Prior to issuing the POWERDOWN command, it is highly recommended that
the user service all pending interrupts through the Sense Interrupt Status command.
Sense Interrupt Status
An interrupt signal is generated by the FDC for one of the following reasons:
1) Upon entering the Result Phase of:
a. Read Data command
b. Read A Track command
c. Read ID command
d. Read Deleted Data command
e. Write Data command
f. Format A Track command
g. Write Deleted Data command
h. Verify command
2) End of Seek, Relative Seek, or Recalibrate command
The Sense Interrupt Status command resets the interrupt signal and, via the IC code and SE bit of Status Register 0,
identifies the cause of the interrupt.
Table 26 – Interrupt Identification
SE
IC
INTERRUPT DUE TO
Polling
0
11
1
00
Normal termination of Seek
or Recalibrate command
Abnormal termination of
Seek or Recalibrate
command
1
01
The Seek, Relative Seek, and Recalibrate commands have no result phase. The Sense Interrupt Status command must
be issued immediately after these commands to terminate them and to provide verification of the head position (PCN).
The H (Head Address) bit in ST0 will always return a "0". If a Sense Interrupt Status is not issued, the drive will continue
to be BUSY and may affect the operation of the next command.
Sense Drive Status
Sense Drive Status obtains drive status information. It has not execution phase and goes directly to the result phase
from the command phase. Status Register 3 contains the drive status information.
SMSC DS – LPC47M14X
Page 56
Rev. 05/02/2000
Specify
The Specify command sets the initial values for each of the three internal times. The HUT (Head Unload Time) defines
the time from the end of the execution phase of one of the read/write commands to the head unload state. The SRT
(Step Rate Time) defines the time interval between adjacent step pulses. Note that the spacing between the first and
second step pulses may be shorter than the remaining step pulses. The HLT (Head Load Time) defines the time
between when the Head Load signal goes high and the read/write operation starts. The values change with the data
rate speed selection and are documented in Table 27. The values are the same for MFM and FM.
A DMA operation is selected by the ND bit. When ND is "0", the DMA mode is selected. This part does not support non-
DMA mode. In DMA mode, data transfers are signaled by the DMA request cycles.
Configure
The Configure command is issued to select the special features of the FDC. A Configure command need not be issued
if the default values of the FDC meet the system requirements.
Table 27 – Drive Control Delays (ms)
HUT
SRT
2M
64
4
1M
128
8
500K 300K 250K
2M
4
3.75
..
0.5
0.25
1M
8
7.5
..
1
0.5
500K 300K 250K
0
1
..
E
F
256
16
426
26.7
..
512
32
16
15
..
26.7
25
32
30
..
..
..
..
..
..
56
60
112
120
224
240
373
400
448
480
2
3.33
1.67
4
1
2
HLT
2M
64
0.5
1
1M
128
1
500K
256
2
4
..
300K
426
3.3
250K
512
4
8
.
00
01
02
..
7F
7F
2
6.7
..
..
..
63
63.5
126
127
252
254
420
423
504
508
Configure Default Values:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
EIS - No Implied Seeks
EFIFO - FIFO Disabled
POLL - Polling Enabled
FIFOTHR - FIFO Threshold Set to 1 Byte
PRETRK - Pre-Compensation Set to Track 0
EIS - Enable Implied Seek. When set to "1", the FDC will perform a Seek operation before executing a read or write
command. Defaults to no implied seek.
EFIFO - A "1" disables the FIFO (default). This means data transfers are asked for on a byte-by-byte basis. Defaults to
"1", FIFO disabled. The threshold defaults to "1".
POLL - Disable polling of the drives. Defaults to "0", polling enabled. When enabled, a single interrupt is generated
after a reset. No polling is performed while the drive head is loaded and the head unload delay has not expired.
FIFOTHR - The FIFO threshold in the execution phase of read or write commands. This is programmable from 1 to 16
bytes. Defaults to one byte. A "00" selects one byte; "0F" selects 16 bytes.
PRETRK - Pre-Compensation Start Track Number. Programmable from track 0 to 255. Defaults to track 0. A "00"
selects track 0; "FF" selects track 255.
Version
The Version command checks to see if the controller is an enhanced type or the older type (765A). A value of 90 H is
returned as the result byte.
Relative Seek
The command is coded the same as for Seek, except for the MSB of the first byte and the DIR bit.
SMSC DS – LPC47M14X
Page 57
Rev. 05/02/2000
DIR
Head Step Direction Control
RCN Relative Cylinder Number that determines how many tracks to step the head in or out from the current track
number.
DIR
ACTION
0
Step Head Out
1
Step Head In
The Relative Seek command differs from the Seek command in that it steps the head the absolute number of tracks
specified in the command instead of making a comparison against an internal register. The Seek command is good for
drives that support a maximum of 256 tracks. Relative Seeks cannot be overlapped with other Relative Seeks. Only
one Relative Seek can be active at a time. Relative Seeks may be overlapped with Seeks and Recalibrates. Bit 4 of
Status Register 0 (EC) will be set if Relative Seek attempts to step outward beyond Track 0.
As an example, assume that a floppy drive has 300 useable tracks. The host needs to read track 300 and the head is
on any track (0-255). If a Seek command is issued, the head will stop at track 255. If a Relative Seek command is
issued, the FDC will move the head the specified number of tracks, regardless of the internal cylinder position register
(but will increment the register). If the head was on track 40 (d), the maximum track that the FDC could position the head
on using Relative Seek will be 295 (D), the initial track + 255 (D). The maximum count that the head can be moved with
a single Relative Seek command is 255 (D).
The internal register, PCN, will overflow as the cylinder number crosses track 255 and will contain 39 (D). The resulting
PCN value is thus (RCN + PCN) mod 256. Functionally, the FDC starts counting from 0 again as the track number goes
above 255 (D). It is the user's responsibility to compensate FDC functions (precompensation track number) when
accessing tracks greater than 255. The FDC does not keep track that it is working in an "extended track area" (greater
than 255). Any command issued will use the current PCN value except for the Recalibrate command, which only looks
for the TRACK0 signal. Recalibrate will return an error if the head is farther than 79 due to its limitation of issuing a
maximum of 80 step pulses. The user simply needs to issue a second Recalibrate command. The Seek command and
implied seeks will function correctly within the 44 (D) track (299-255) area of the "extended track area". It is the user's
responsibility not to issue a new track position that will exceed the maximum track that is present in the extended area.
To return to the standard floppy range (0-255) of tracks, a Relative Seek should be issued to cross the track 255
boundary.
A Relative Seek can be used instead of the normal Seek, but the host is required to calculate the difference between the
current head location and the new (target) head location. This may require the host to issue a Read ID command to
ensure that the head is physically on the track that software assumes it to be. Different FDC commands will return
different cylinder results, which may be difficult to keep track of with software without the Read ID command.
Perpendicular Mode
The Perpendicular Mode command should be issued prior to executing Read/Write/Format commands that access a
disk drive with perpendicular recording capability. With this command, the length of the Gap2 field and VCO enable
timing can be altered to accommodate the unique requirements of these drives.
Table 28 describes the effects of the WGATE and GAP bits for the Perpendicular Mode command. Upon a reset, the
FDC will default to the conventional mode (WGATE = 0, GAP = 0).
Selection of the 500 Kbps and 1 Mbps perpendicular modes is independent of the actual data rate selected in the Data
Rate Select Register. The user must ensure that these two data rates remain consistent.
The Gap2 and VCO timing requirements for perpendicular recording type drives are dictated by the design of the
read/write head. In the design of this head, a pre-erase head precedes the normal read/write head by a distance of 200
micrometers. This works out to about 38 bytes at a 1 Mbps recording density. Whenever the write head is enabled by
the Write Gate signal, the pre-erase head is also activated at the same time. Thus, when the write head is initially turned
on, flux transitions recorded on the media for the first 38 bytes will not be preconditioned with the pre-erase head since it
has not yet been activated. To accommodate this head activation and deactivation time, the Gap2 field is expanded to a
length of 41 bytes. The format field shown on Page 58 illustrates the change in the Gap2 field size for the
perpendicular format.
On the read back by the FDC, the controller must begin synchronization at the beginning of the sync field. For the
conventional mode, the internal PLL VCO is enabled (VCOEN) approximately 24 bytes from the start of the Gap2 field.
But, when the controller operates in the 1 Mbps perpendicular mode (WGATE = 1, GAP = 1), VCOEN goes active after
43 bytes to accommodate the increased Gap2 field size. For both cases, and approximate two-byte cushion is
maintained from the beginning of the sync field for the purposes of avoiding write splices in the presence of motor speed
variation.
For the Write Data case, the FDC activates Write Gate at the beginning of the sync field under the conventional mode.
The controller then writes a new sync field, data address mark, data field, and CRC. With the pre-erase head of the
perpendicular drive, the write head must be activated in the Gap2 field to insure a proper write of the new sync field. For
the 1 Mbps perpendicular mode (WGATE = 1, GAP = 1), 38 bytes will be written in the Gap2 space. Since the bit density
is proportional to the data rate, 19 bytes will be written in the Gap2 field for the 500 Kbps perpendicular mode (WGATE =
1, GAP =0).
It should be noted that none of the alterations in Gap2 size, VCO timing, or Write Gate timing affect normal program
flow. The information provided here is just for background purposes and is not needed for normal operation. Once the
Perpendicular Mode command is invoked, FDC software behavior from the user standpoint is unchanged.
The perpendicular mode command is enhanced to allow specific drives to be designated Perpendicular recording drives.
This enhancement allows data transfers between Conventional and Perpendicular drives without having to issue
Perpendicular mode commands between the accesses of the different drive types, nor having to change write pre-
compensation values.
When both GAP and WGATE bits of the PERPENDICULAR MODE COMMAND are both programmed to "0"
(Conventional mode), then D0, D1, D2, D3, and D4 can be programmed independently to "1" for that drive to be set
automatically to Perpendicular mode. In this mode the following set of conditions also apply:
1) The GAP2 written to a perpendicular drive during a write operation will depend upon the programmed data rate.
2) The write pre-compensation given to a perpendicular mode drive will be 0ns.
3) For D0-D3 programmed to "0" for conventional mode drives any data written will be at the currently programmed
write pre-compensation.
Note: Bits D0-D3 can only be overwritten when OW is programmed as a "1".If either GAP or WGATE is a "1" then D0-
D3 are ignored.
Software and hardware resets have the following effect on the PERPENDICULAR MODE COMMAND:
1) "Software" resets (via the DOR or DSR registers) will only clear GAP and WGATE bits to "0". D0-D3 are
unaffected and retain their previous value.
2) "Hardware" resets will clear all bits (GAP, WGATE and D0-D3) to "0", i.e. all conventional mode.
Table 28 – Effects of WGATE and GAP Bits
PORTION OF
GAP 2
LENGTH OF
GAP2 FORMAT
FIELD
WRITTEN BY
WRITE DATA
OPERATION
WGATE GAP
MODE
0
0
Conventional
Perpendicular
(500 Kbps)
22 Bytes
0 Bytes
0
1
22 Bytes
19 Bytes
1
1
0
1
Reserved
22 Bytes
41 Bytes
0 Bytes
(Conventional)
Perpendicular
(1 Mbps)
38 Bytes
LOCK
In order to protect systems with long DMA latencies against older application software that can disable the FIFO the
LOCK Command has been added. This command should only be used by the FDC routines, and application software
should refrain from using it. If an application calls for the FIFO to be disabled then the CONFIGURE command should
be used.
The LOCK command defines whether the EFIFO, FIFOTHR, and PRETRK parameters of the CONFIGURE command
can be RESET by the DOR and DSR registers. When the LOCK bit is set to logic "1" all subsequent "software RESETS
by the DOR and DSR registers will not change the previously set parameters to their default values. All "hardware"
RESET from the PCI_RESET# pin will set the LOCK bit to logic "0" and return the EFIFO, FIFOTHR, and PRETRK to
their default values. A status byte is returned immediately after issuing a LOCK command. This byte reflects the value
of the LOCK bit set by the command byte.
SMSC DS – LPC47M14X
Page 59
Rev. 05/02/2000
ENHANCED DUMPREG
The DUMPREG command is designed to support system run-time diagnostics and application software development
and debug. To accommodate the LOCK command and the enhanced PERPENDICULAR MODE command the eighth
byte of the DUMPREG command has been modified to contain the additional data from these two commands.
COMPATIBILITY
The LPC47M14x was designed with software compatibility in mind. It is a fully backwards- compatible solution with the
older generation 765A/B disk controllers. The FDC also implements on-board registers for compatibility with the PS/2, as
well as PC/AT and PC/XT, floppy disk controller subsystems. After a hardware reset of the FDC, all registers, functions
and enhancements default to a PC/AT, PS/2 or PS/2 Model 30 compatible operating mode, depending on how the
IDENT and MFM bits are configured by the system BIOS.
6.6 SERIAL PORT (UART)
The LPC47M14x incorporates two full function UARTs. They are compatible with the NS16450, the 16450 ACE
registers and the NS16C550A. The UARTs perform serial-to-parallel conversion on received characters and parallel-to-
serial conversion on transmit characters. The data rates are independently programmable from 460.8K baud down to
50 baud. The character options are programmable for 1 start; 1, 1.5 or 2 stop bits; even, odd, sticky or no parity; and
prioritized interrupts. The UARTs each contain a programmable baud rate generator that is capable of dividing the input
clock or crystal by a number from 1 to 65535. The UARTs are also capable of supporting the MIDI data rate. Refer to
the Configuration Registers for information on disabling, power down and changing the base address of the UARTs.
The interrupt from a UART is enabled by programming OUT2 of that UART to a logic "1". OUT2 being a logic "0"
disables that UARTs interrupt. The second UART also supports IrDA, HP-SIR and ASK-IR modes of operation.
Note: The UARTs 1 and 2 may be configured to share an interrupt. Refer to the Configuration section for more
information.
REGISTER DESCRIPTION
Addressing of the accessible registers of the Serial Port is shown below. The base addresses of the serial ports are
defined by the configuration registers (see “Configuration” section). The Serial Port registers are located at sequentially
increasing addresses above these base addresses. The LPC47M14x contains two serial ports, each of which contain a
register set as described below.
Table 29 – Addressing the Serial Port
DLAB*
A2
0
0
0
0
0
0
1
1
1
1
0
0
A1
0
0
0
1
1
1
0
0
1
1
0
0
A0
0
0
1
0
0
1
0
1
0
1
0
1
REGISTER NAME
Receive Buffer (read)
Transmit Buffer (write)
0
0
0
Interrupt Enable (read/write)
Interrupt Identification (read)
FIFO Control (write)
Line Control (read/write)
Modem Control (read/write)
Line Status (read/write)
Modem Status (read/write)
Scratchpad (read/write)
Divisor LSB (read/write)
Divisor MSB (read/write
X
X
X
X
X
X
X
1
1
*Note: DLAB is Bit 7 of the Line Control Register
SMSC DS – LPC47M14X
Page 60
Rev. 05/02/2000
The following section describes the operation of the registers.
RECEIVE BUFFER REGISTER (RB)
Address Offset = 0H, DLAB = 0, READ ONLY
This register holds the received incoming data byte. Bit 0 is the least significant bit, which is transmitted and received
first. Received data is double buffered; this uses an additional shift register to receive the serial data stream and convert
it to a parallel 8 bit word which is transferred to the Receive Buffer register. The shift register is not accessible.
TRANSMIT BUFFER REGISTER (TB)
Address Offset = 0H, DLAB = 0, WRITE ONLY
This register contains the data byte to be transmitted. The transmit buffer is double buffered, utilizing an additional shift
register (not accessible) to convert the 8 bit data word to a serial format. This shift register is loaded from the Transmit
Buffer when the transmission of the previous byte is complete.
INTERRUPT ENABLE REGISTER (IER)
Address Offset = 1H, DLAB = 0, READ/WRITE
The lower four bits of this register control the enables of the five interrupt sources of the Serial Port interrupt. It is
possible to totally disable the interrupt system by resetting bits 0 through 3 of this register. Similarly, setting the
appropriate bits of this register to a high, selected interrupts can be enabled. Disabling the interrupt system inhibits the
Interrupt Identification Register and disables any Serial Port interrupt out of the LPC47M14x. All other system functions
operate in their normal manner, including the Line Status and MODEM Status Registers. The contents of the Interrupt
Enable Register are described below.
Bit 0
This bit enables the Received Data Available Interrupt (and timeout interrupts in the FIFO mode) when set to logic "1".
Bit 1
This bit enables the Transmitter Holding Register Empty Interrupt when set to logic "1".
Bit 2
This bit enables the Received Line Status Interrupt when set to logic "1". The error sources causing the interrupt are
Overrun, Parity, Framing and Break. The Line Status Register must be read to determine the source.
Bit 3
This bit enables the MODEM Status Interrupt when set to logic "1". This is caused when one of the Modem Status
Register bits changes state.
Bits 4 through 7
These bits are always logic "0".
FIFO CONTROL REGISTER (FCR)
Address Offset = 2H, DLAB = X, WRITE
This is a write only register at the same location as the IIR. This register is used to enable and clear the FIFOs, set the
RCVR FIFO trigger level. Note: DMA is not supported. The UART1 and UART2 FCR’s are shadowed in the UART1
FIFO Control Shadow Register (runtime register at offset 0x20) and UART2 FIFO Control Shadow Register (runtime
register at offset 0x21).
Bit 0
Setting this bit to a logic "1" enables both the XMIT and RCVR FIFOs. Clearing this bit to a logic "0" disables both the
XMIT and RCVR FIFOs and clears all bytes from both FIFOs. When changing from FIFO Mode to non-FIFO (16450)
mode, data is automatically cleared from the FIFOs. This bit must be a 1 when other bits in this register are written to or
they will not be properly programmed.
Bit 1
Setting this bit to a logic "1" clears all bytes in the RCVR FIFO and resets its counter logic to 0. The shift register is not
cleared. This bit is self-clearing.
Bit 2
Setting this bit to a logic "1" clears all bytes in the XMIT FIFO and resets its counter logic to 0. The shift register is not
cleared. This bit is self-clearing.
Bit 3
Writing to this bit has no effect on the operation of the UART. The RXRDY and TXRDY pins are not available on this
chip.
SMSC DS – LPC47M14X
Page 61
Rev. 05/02/2000
Bit 4,5
Reserved
Bit 6,7
These bits are used to set the trigger level for the RCVR FIFO interrupt.
INTERRUPT IDENTIFICATION REGISTER (IIR)
Address Offset = 2H, DLAB = X, READ
By accessing this register, the host CPU can determine the highest priority interrupt and its source. Four levels of
priority interrupt exist. They are in descending order of priority:
1) Receiver Line Status (highest priority)
2) Received Data Ready
3) Transmitter Holding Register Empty
4) MODEM Status (lowest priority)
Information indicating that a prioritized interrupt is pending and the source of that interrupt is stored in the Interrupt
Identification Register (refer to Interrupt Control Table). When the CPU accesses the IIR, the Serial Port freezes all
interrupts and indicates the highest priority pending interrupt to the CPU. During this CPU access, even if the Serial Port
records new interrupts, the current indication does not change until access is completed. The contents of the IIR are
described below.
Bit 0
This bit can be used in either a hardwired prioritized or polled environment to indicate whether an interrupt is pending.
When bit 0 is a logic "0", an interrupt is pending and the contents of the IIR may be used as a pointer to the appropriate
internal service routine. When bit 0 is a logic "1", no interrupt is pending.
Bits 1 and 2
These two bits of the IIR are used to identify the highest priority interrupt pending as indicated by the Interrupt Control
Table.
Bit 3
In non-FIFO mode, this bit is a logic "0". In FIFO mode this bit is set along with bit 2 when a timeout interrupt is pending.
Bits 4 and 5
These bits of the IIR are always logic "0".
Bits 6 and 7
These two bits are set when the FIFO CONTROL Register bit 0 equals 1.
RCVR FIFO
Bit 7 Bit 6 Trigger Level (BYTES)
0
0
1
1
0
1
0
1
1
4
8
14
SMSC DS – LPC47M14X
Page 62
Rev. 05/02/2000
Table 30 – Interrupt Control Table
FIFO
MODE
ONLY
INTERRUPT
IDENTIFICATION
REGISTER
INTERRUPT SET AND RESET FUNCTIONS
INTERRUPT
PRIORITY INTERRUPT
INTERRUPT
SOURCE
RESET
LEVEL
TYPE
BIT 3
BIT 2 BIT 1 BIT 0
CONTROL
0
0
0
1
-
None
None
-
Overrun Error,
Receiver Line
Status
Parity Error,
Reading the Line
Status Register
0
1
1
0
Highest
Framing Error or
Break Interrupt
Read Receiver
Buffer or the FIFO
drops below the
trigger level.
Received Data
Available
Receiver Data
Available
0
1
1
0
0
0
0
Second
No Characters
Have Been
Removed From or
Input to the RCVR
FIFO during the
last 4 Char times
and there is at
Character
Timeout
Reading the
Receiver Buffer
Register
1
Second
Indication
least 1 char in it
during this time
Reading the IIR
Register (if Source
of Interrupt) or
Writing the
Transmitter
Holding
Transmitter
Holding Register
Empty
0
0
0
0
1
0
0
0
Third
Register Empty
Transmitter
Holding Register
Clear to Send or
Data Set Ready or
Ring Indicator or
Data Carrier
Reading the
MODEM Status
Register
MODEM
Status
Fourth
Detect
LINE CONTROL REGISTER (LCR)
Address Offset = 3H, DLAB = 0, READ/WRITE
Start LSB Data 5-8 bits MSB Parity Stop
Serial Data
This register contains the format information of the serial line. The bit definitions are:
Bits 0 and 1
These two bits specify the number of bits in each transmitted or received serial character. The encoding of bits 0 and 1
is as follows:
The Start, Stop and Parity bits are not included in the word length.
BIT 1
BIT 0 WORD LENGTH
0
0
1
1
0
1
0
1
5 Bits
6 Bits
7 Bits
8 Bits
SMSC DS – LPC47M14X
Page 63
Rev. 05/02/2000
Bit 2
This bit specifies the number of stop bits in each transmitted or received serial character. The following table
summarizes the information.
NUMBER OF
STOP BITS
BIT 2 WORD LENGTH
0
1
1
1
1
--
1
1.5
2
2
2
5 bits
6 bits
7 bits
8 bits
Note: The receiver will ignore all stop bits beyond the first, regardless of the number used in transmitting.
Bit 3
Parity Enable bit. When bit 3 is a logic "1", a parity bit is generated (transmit data) or checked (receive data) between
the last data word bit and the first stop bit of the serial data. (The parity bit is used to generate an even or odd number of
1s when the data word bits and the parity bit are summed).
Bit 4
Even Parity Select bit. When bit 3 is a logic "1" and bit 4 is a logic "0", an odd number of logic "1"'s is transmitted or
checked in the data word bits and the parity bit. When bit 3 is a logic "1" and bit 4 is a logic "1" an even number of bits is
transmitted and checked.
Bit 5
This bit is the Stick Parity bit. When parity is enabled it is used in conjunction with bit 4 to select Mark or Space Parity.
When LCR bits 3, 4 and 5 are 1 the Parity bit is transmitted and checked as a 0 (Space Parity). If bits 3 and 5 are 1 and
bit 4 is a 0, then the Parity bit is transmitted and checked as 1 (Mark Parity). If bit 5 is 0 Stick Parity is disabled.
Bit 6
Set Break Control bit. When bit 6 is a logic "1", the transmit data output (TXD) is forced to the Spacing or logic "0" state
and remains there (until reset by a low level bit 6) regardless of other transmitter activity. This feature enables the Serial
Port to alert a terminal in a communications system.
Bit 7
Divisor Latch Access bit (DLAB). It must be set high (logic "1") to access the Divisor Latches of the Baud Rate
Generator during read or write operations. It must be set low (logic "0") to access the Receiver Buffer Register, the
Transmitter Holding Register, or the Interrupt Enable Register.
MODEM CONTROL REGISTER (MCR)
Address Offset = 4H, DLAB = X, READ/WRITE
This 8 bit register controls the interface with the MODEM or data set (or device emulating a MODEM). The contents of
the MODEM control register are described below.
Bit 0
This bit controls the Data Terminal Ready (nDTR) output. When bit 0 is set to a logic "1", the nDTR output is forced to a
logic "0". When bit 0 is a logic "0", the nDTR output is forced to a logic "1".
Bit 1
This bit controls the Request To Send (nRTS) output. Bit 1 affects the nRTS output in a manner identical to that
described above for bit 0.
Bit 2
This bit controls the Output 1 (OUT1) bit. This bit does not have an output pin and can only be read or written by the
CPU.
Bit 3
Output 2 (OUT2). This bit is used to enable an UART interrupt. When OUT2 is a logic "0", the serial port interrupt
output is forced to a high impedance state - disabled. When OUT2 is a logic "1", the serial port interrupt outputs are
enabled.
SMSC DS – LPC47M14X
Page 64
Rev. 03/19/2001
Bit 4
This bit provides the loopback feature for diagnostic testing of the Serial Port. When bit 4 is set to logic "1", the following
occur:
1) The TXD is set to the Marking State(logic "1").
2) The receiver Serial Input (RXD) is disconnected.
3) The output of the Transmitter Shift Register is "looped back" into the Receiver Shift Register input.
4) All MODEM Control inputs (nCTS, nDSR, nRI and nDCD) are disconnected.
5) The four MODEM Control outputs (nDTR, nRTS, OUT1 and OUT2) are internally connected to the four MODEM
Control inputs (nDSR, nCTS, RI, DCD).
6) The Modem Control output pins are forced inactive high.
7) Data that is transmitted is immediately received.
This feature allows the processor to verify the transmit and receive data paths of the Serial Port. In the diagnostic mode,
the receiver and the transmitter interrupts are fully operational. The MODEM Control Interrupts are also operational but
the interrupts' sources are now the lower four bits of the MODEM Control Register instead of the MODEM Control
inputs. The interrupts are still controlled by the Interrupt Enable Register.
Bits 5 through 7
These bits are permanently set to logic zero.
LINE STATUS REGISTER (LSR)
Address Offset = 5H, DLAB = X, READ/WRITE
Bit 0
Data Ready (DR). It is set to a logic "1" whenever a complete incoming character has been received and transferred
into the Receiver Buffer Register or the FIFO. Bit 0 is reset to a logic "0" by reading all of the data in the Receive Buffer
Register or the FIFO.
Bit 1
Overrun Error (OE). Bit 1 indicates that data in the Receiver Buffer Register was not read before the next character was
transferred into the register, thereby destroying the previous character. In FIFO mode, an overrun error will occur only
when the FIFO is full and the next character has been completely received in the shift register, the character in the shift
register is overwritten but not transferred to the FIFO. The OE indicator is set to a logic "1" immediately upon detection of
an overrun condition, and reset whenever the Line Status Register is read.
Bit 2
Parity Error (PE). Bit 2 indicates that the received data character does not have the correct even or odd parity, as
selected by the even parity select bit. The PE is set to a logic "1" upon detection of a parity error and is reset to a logic
"0" whenever the Line Status Register is read. In the FIFO mode this error is associated with the particular character in
the FIFO it applies to. This error is indicated when the associated character is at the top of the FIFO.
Bit 3
Framing Error (FE). Bit 3 indicates that the received character did not have a valid stop bit. Bit 3 is set to a logic "1"
whenever the stop bit following the last data bit or parity bit is detected as a zero bit (Spacing level). The FE is reset to a
logic "0" whenever the Line Status Register is read. In the FIFO mode this error is associated with the particular
character in the FIFO it applies to. This error is indicated when the associated character is at the top of the FIFO. The
Serial Port will try to resynchronize after a framing error. To do this, it assumes that the framing error was due to the
next start bit, so it samples this 'start' bit twice and then takes in the 'data'.
Bit 4
Break Interrupt (BI). Bit 4 is set to a logic "1" whenever the received data input is held in the Spacing state (logic "0") for
longer than a full word transmission time (that is, the total time of the start bit + data bits + parity bits + stop bits). The BI
is reset after the CPU reads the contents of the Line Status Register. In the FIFO mode this error is associated with the
particular character in the FIFO it applies to. This error is indicated when the associated character is at the top of the
FIFO. When break occurs only one zero character is loaded into the FIFO. Restarting after a break is received,
requires the serial data (RXD) to be logic "1" for at least 1/2 bit time.
Note: Bits 1 through 4 are the error conditions that produce a Receiver Line Status Interrupt whenever any of the
corresponding conditions are detected and the interrupt is enabled.
Bit 5
Transmitter Holding Register Empty (THRE). Bit 5 indicates that the Serial Port is ready to accept a new character for
transmission. In addition, this bit causes the Serial Port to issue an interrupt when the Transmitter Holding Register
interrupt enable is set high. The THRE bit is set to a logic "1" when a character is transferred from the Transmitter
Holding Register into the Transmitter Shift Register. The bit is reset to logic "0" whenever the CPU loads the Transmitter
SMSC DS – LPC47M14X
Page 65
Rev. 03/19/2001
Holding Register. In the FIFO mode this bit is set when the XMIT FIFO is empty, it is cleared when at least 1 byte is
written to the XMIT FIFO. Bit 5 is a read only bit.
Bit 6
Transmitter Empty (TEMT). Bit 6 is set to a logic "1" whenever the Transmitter Holding Register (THR) and Transmitter
Shift Register (TSR) are both empty. It is reset to logic "0" whenever either the THR or TSR contains a data character.
Bit 6 is a read only bit. In the FIFO mode this bit is set whenever the THR and TSR are both empty,
Bit 7
This bit is permanently set to logic "0" in the 450 mode. In the FIFO mode, this bit is set to a logic "1" when there is at
least one parity error, framing error or break indication in the FIFO. This bit is cleared when the LSR is read if there are
no subsequent errors in the FIFO.
MODEM STATUS REGISTER (MSR)
Address Offset = 6H, DLAB = X, READ/WRITE
This 8 bit register provides the current state of the control lines from the MODEM (or peripheral device). In addition to
this current state information, four bits of the MODEM Status Register (MSR) provide change information. These bits are
set to logic "1" whenever a control input from the MODEM changes state. They are reset to logic "0" whenever the
MODEM Status Register is read.
Bit 0
Delta Clear To Send (DCTS). Bit 0 indicates that the nCTS input to the chip has changed state since the last time the
MSR was read.
Bit 1
Delta Data Set Ready (DDSR). Bit 1 indicates that the nDSR input has changed state since the last time the MSR was
read.
Bit 2
Trailing Edge of Ring Indicator (TERI). Bit 2 indicates that the nRI input has changed from logic "0" to logic "1".
Bit 3
Delta Data Carrier Detect (DDCD). Bit 3 indicates that the nDCD input to the chip has changed state.
Note: Whenever bit 0, 1, 2, or 3 is set to a logic "1", a MODEM Status Interrupt is generated.
Bit 4
This bit is the complement of the Clear To Send (nCTS) input. If bit 4 of the MCR is set to logic "1", this bit is equivalent
to nRTS in the MCR.
Bit 5
This bit is the complement of the Data Set Ready (nDSR) input. If bit 4 of the MCR is set to logic "1", this bit is
equivalent to DTR in the MCR.
Bit 6
This bit is the complement of the Ring Indicator (nRI) input. If bit 4 of the MCR is set to logic "1", this bit is equivalent to
OUT1 in the MCR.
Bit 7
This bit is the complement of the Data Carrier
Detect (nDCD) input. If bit 4 of the MCR is set to logic "1", this bit is equivalent to OUT2 in the MCR.
SCRATCHPAD REGISTER (SCR)
Address Offset =7H, DLAB =X, READ/WRITE
This 8 bit read/write register has no effect on the operation of the Serial Port. It is intended as a scratchpad register to
be used by the programmer to hold data temporarily.
PROGRAMMABLE BAUD RATE GENERATOR (AND DIVISOR LATCHES DLH, DLL)
The Serial Port contains a programmable Baud Rate Generator that is capable of dividing the internal PLL clock by any
divisor from 1 to 65535. The internal PLL clock is divided down to generate a 1.8462MHz frequency for Baud Rates less
than 38.4k, a 1.8432MHz frequency for 115.2k, a 3.6864MHz frequency for 230.4k and a 7.3728MHz frequency for
460.8k. This output frequency of the Baud Rate Generator is 16x the Baud rate. Two 8 bit latches store the divisor in 16
bit binary format. These Divisor Latches must be loaded during initialization in order to insure desired operation of the
Baud Rate Generator. Upon loading either of the Divisor Latches, a 16 bit Baud counter is immediately loaded. This
prevents long counts on initial load. If a 0 is loaded into the BRG registers the output divides the clock by the number 3.
If a 1 is loaded the output is the inverse of the input oscillator. If a two is loaded the output is a divide by 2 signal with a
SMSC DS – LPC47M14X
Page 66
Rev. 03/19/2001
50% duty cycle. If a 3 or greater is loaded the output is low for 2 bits and high for the remainder of the count. The input
clock to the BRG is a 1.8462 MHz clock.
Table 31 shows the baud rates possible.
Effect Of The Reset on Register File
The Reset Function (details the effect of the Reset input on each of the registers of the Serial Port.
FIFO INTERRUPT MODE OPERATION
When the RCVR FIFO and receiver interrupts are enabled (FCR bit 0 = "1", IER bit 0 = "1"), RCVR interrupts occur as
follows:
ꢀ The receive data available interrupt will be issued when the FIFO has reached its programmed trigger level; it is
cleared as soon as the FIFO drops below its programmed trigger level.
ꢀ The IIR receive data available indication also occurs when the FIFO trigger level is reached. It is cleared when
the FIFO drops below the trigger level.
ꢀ The receiver line status interrupt (IIR=06H), has higher priority than the received data available (IIR=04H)
interrupt.
ꢀ The data ready bit (LSR bit 0) is set as soon as a character is transferred from the shift register to the RCVR
FIFO. It is reset when the FIFO is empty.
When RCVR FIFO and receiver interrupts are enabled, RCVR FIFO timeout interrupts occur as follows:
1)
A FIFO timeout interrupt occurs if all the following conditions exist:
ꢀ
ꢀ
At least one character is in the FIFO.
The most recent serial character received was longer than 4 continuous character times ago. (If 2 stop bits
are programmed, the second one is included in this time delay).
ꢀ
The most recent CPU read of the FIFO was longer than 4 continuous character times ago.
This will cause a maximum character received to interrupt issued delay of 160 msec at 300 BAUD with a 12 bit
character.
ꢀ
ꢀ
ꢀ
Character times are calculated by using the RCLK input for a clock signal (this makes the delay proportional
to the baudrate).
When a timeout interrupt has occurred it is cleared and the timer reset when the CPU reads one character
from the RCVR FIFO.
When a timeout interrupt has not occurred the timeout timer is reset after a new character is received or after
the CPU reads the RCVR FIFO.
When the XMIT FIFO and transmitter interrupts are enabled (FCR bit 0 = "1", IER bit 1 = "1"), XMIT interrupts occur as
follows:
ꢀ
The transmitter holding register interrupt (02H) occurs when the XMIT FIFO is empty; it is cleared as soon as
the transmitter holding register is written to (1 of 16 characters may be written to the XMIT FIFO while
servicing this interrupt) or the IIR is read.
ꢀ
The transmitter FIFO empty indications will be delayed 1 character time minus the last stop bit time whenever
the following occurs: THRE=1 and there have not been at least two bytes at the same time in the transmitter
FIFO since the last THRE=1. The transmitter interrupt after changing FCR0 will be immediate, if it is enabled.
Character timeout and RCVR FIFO trigger level interrupts have the same priority as the current received data available
interrupt; XMIT FIFO empty has the same priority as the current transmitter holding register empty interrupt.
SMSC DS – LPC47M14X
Page 67
Rev. 03/19/2001
FIFO POLLED MODE OPERATION
With FCR bit 0 = "1" resetting IER bits 0, 1, 2 or 3 or all to zero puts the UART in the FIFO Polled Mode of operation.
Since the RCVR and XMITTER are controlled separately, either one or both can be in the polled mode of operation. In
this mode, the user's program will check RCVR and XMITTER status via the LSR. LSR definitions for the FIFO Polled
Mode are as follows:
ꢀ
ꢀ
Bit 0=1 as long as there is one byte in the RCVR FIFO.
Bits 1 to 4 specify which error(s) have occurred. Character error status is handled the same way as when
in the interrupt mode, the IIR is not affected since EIR bit 2=0.
Bit 5 indicates when the XMIT FIFO is empty.
ꢀ
ꢀ
ꢀ
Bit 6 indicates that both the XMIT FIFO and shift register are empty.
Bit 7 indicates whether there are any errors in the RCVR FIFO.
There is no trigger level reached or timeout condition indicated in the FIFO Polled Mode, however, the RCVR and XMIT
FIFOs are still fully capable of holding characters.
Table 31 – Baud Rates
DESIRED
BAUD RATE
50
DIVISOR USED TO
PERCENT ERROR DIFFERENCE
HIGH
GENERATE 16X CLOCK
BETWEEN DESIRED AND ACTUAL1
SPEED BIT2
2304
1536
1047
857
768
384
192
96
0.001
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
1
75
-
-
110
134.5
150
0.004
-
300
-
600
-
1200
-
1800
64
-
2000
58
0.005
2400
48
-
3600
32
-
-
4800
24
7200
16
-
9600
12
-
19200
38400
57600
115200
230400
460800
6
-
3
0.030
0.16
0.16
0.16
0.16
2
1
32770
32769
1
Note1: The percentage error for all baud rates, except where indicated otherwise, is 0.2%.
Note 2: The High Speed bit is located in the Device Configuration Space.
SMSC DS – LPC47M14X
Page 68
Rev. 03/19/2001
Table 32 – Reset Function Table
RESET CONTROL
REGISTER/SIGNAL
Interrupt Enable Register
Interrupt Identification Reg.
FIFO Control
RESET STATE
RESET
All bits low
RESET
Bit 0 is high; Bits 1 - 7 low
RESET
All bits low
Line Control Reg.
RESET
All bits low
MODEM Control Reg.
Line Status Reg.
RESET
RESET
All bits low
All bits low except 5, 6 high
MODEM Status Reg.
TXD1, TXD2
INTRPT (RCVR errs)
INTRPT (RCVR Data Ready) RESET/Read RBR
INTRPT (THRE)
OUT2B
RTSB
DTRB
OUT1B
RESET
RESET
RESET/Read LSR
Bits 0 - 3 low; Bits 4 - 7 input
High
Low
Low
Low
High
High
High
High
RESET/ReadIIR/Write THR
RESET
RESET
RESET
RESET
RESET/
RCVR FIFO
XMIT FIFO
All Bits Low
All Bits Low
FCR1*FCR0/_FCR0
RESET/
FCR1*FCR0/_FCR0
Table 33 – Register Summary for an Individual UART Channel
REGISTER
REGISTER
ADDRESS*
REGISTER NAME
SYMBOL
BIT 0
BIT 1
ADDR = 0
Receive Buffer Register (Read Only)
RBR
Data Bit 0 Data Bit 1
DLAB = 0
(Note 1)
ADDR = 0
DLAB = 0
ADDR = 1
DLAB = 0
Transmitter Holding Register (Write
Only)
Interrupt Enable Register
THR
IER
Data Bit 0
Data Bit 1
Enable
Enable
Received
Data
Transmitter
Holding
Available
Interrupt
(ERDAI)
Register
Empty
Interrupt
(ETHREI)
ADDR = 2
Interrupt Ident. Register (Read Only)
IIR
"0" if
Interrupt ID
Bit
Interrupt
Pending
ADDR = 2
ADDR = 3
FIFO Control Register (Write Only)
Line Control Register
FCR
FIFO Enable RCVR FIFO
Reset
(Note 7)
LCR
Word
Word
Length
Length
Select Bit 0 Select Bit 1
(WLS0)
(WLS1)
ADDR = 4
ADDR = 5
MODEM Control Register
MCR
LSR
Data
Request to
Send (RTS)
Terminal
Ready
(DTR)
Data Ready
Line Status Register
Overrun
(DR)
Error (OE)
SMSC DS – LPC47M14X
Page 69
Rev. 03/19/2001
REGISTER
ADDRESS*
REGISTER
SYMBOL
REGISTER NAME
BIT 0
BIT 1
Delta Clear
ADDR = 6
MODEM Status Register
MSR
Delta Data
Set Ready
(DDSR)
to Send
(DCTS)
ADDR = 7
Scratch Register (Note 4)
Divisor Latch (LS)
SCR
DDL
Bit 0
Bit 0
Bit 1
Bit 1
ADDR = 0
DLAB = 1
ADDR = 1
DLAB = 1
Divisor Latch (MS)
DLM
Bit 8
Bit 9
*DLAB is Bit 7 of the Line Control Register (ADDR = 3).
Note 1: Bit 0 is the least significant bit. It is the first bit serially transmitted or received.
Note 2: When operating in the XT mode, this bit will be set any time that the transmitter shift register is empty.
Table 33 – Register Summary for an Individual UART Channel (continued)
BIT 2
Data Bit 2
Data Bit 2
BIT 3
Data Bit 3
Data Bit 3
BIT 4
Data Bit 4
Data Bit 4
0
BIT 5
Data Bit 5
Data Bit 5
0
BIT 6
Data Bit 6
Data Bit 6
0
BIT 7
Data Bit 7
Data Bit 7
0
Enable
Enable
MODEM
Status
Receiver Line
Status
Interrupt
(ELSI)
Interrupt
(EMSI)
FIFOs
Interrupt ID Bit Interrupt ID Bit 0
(Note 5)
0
FIFOs
Enabled
(Note 5)
Enabled
(Note 5)
XMIT
Reset
FIFO DMA
Select (Note
6)
Mode Reserved
Reserved
RCVR Trigger RCVR Trigger
LSB
MSB
Divisor Latch
Number
Stop
of Parity Enable Even
Parity Stick Parity
Set Break
Access
(DLAB)
Bit
Bits (PEN)
Select (EPS)
(STB)
OUT1
OUT2
Loop
0
0
0
(Note 3)
(Note 3)
Parity
(PE)
Error Framing Error Break
(FE)
Transmitter
Transmitter
Error in RCVR
Interrupt (BI)
Holding
Register
(THRE)
Empty (TEMT) FIFO (Note 5)
(Note 2)
Data Carrier
Detect (DCD)
Trailing Edge Delta
Data Clear to Send Data
Set Ring Indicator
Ring Indicator Carrier Detect (CTS)
Ready (DSR) (RI)
(TERI)
Bit 2
(DDCD)
Bit 3
Bit 4
Bit 4
Bit 12
Bit 5
Bit 5
Bit 13
Bit 6
Bit 6
Bit 14
Bit 7
Bit 7
Bit 15
Bit 2
Bit 3
Bit 10
Bit 11
Note 3: This bit no longer has a pin associated with it.
Note 4: When operating in the XT mode, this register is not available.
Note 5: These bits are always zero in the non-FIFO mode.
Note 6: Writing a one to this bit has no effect. DMA modes are not supported in this chip.
Note 7: The UART1 and UART2 FCR’s are shadowed in the UART1 FIFO Control Shadow Register (runtime
register at offset 0x20) and UART2 FIFO Control Shadow Register (runtime register at offset 0x21).
SMSC DS – LPC47M14X
Page 70
Rev. 03/19/2001
NOTES ON SERIAL PORT OPERATION
FIFO MODE OPERATION:
GENERAL
The RCVR FIFO will hold up to 16 bytes regardless of which trigger level is selected.
TX AND RX FIFO OPERATION
The Tx portion of the UART transmits data through TXD as soon as the CPU loads a byte into the Tx FIFO. The UART
will prevent loads to the Tx FIFO if it currently holds 16 characters. Loading to the Tx FIFO will again be enabled
as soon as the next character is transferred to the Tx shift register. These capabilities account for the largely
autonomous operation of the Tx.
The UART starts the above operations typically with a Tx interrupt. The chip issues a Tx interrupt whenever the Tx FIFO
is empty and the Tx interrupt is enabled, except in the following instance. Assume that the Tx FIFO is empty and the
CPU starts to load it. When the first byte enters the FIFO the Tx FIFO empty interrupt will transition from active to
inactive. Depending on the execution speed of the service routine software, the UART may be able to transfer this byte
from the FIFO to the shift register before the CPU loads another byte. If this happens, the Tx FIFO will be empty again
and typically the UARTs interrupt line would transition to the active state. This could cause a system with an interrupt
control unit to record a Tx FIFO empty condition, even though the CPU is currently servicing that interrupt. Therefore,
after the first byte has been loaded into the FIFO the UART will wait one serial character transmission time
before issuing a new Tx FIFO empty interrupt. This one character Tx interrupt delay will remain active until at
least two bytes have the Tx FIFO empties after this condition, the Tx been loaded into the FIFO, concurrently.
When interrupt will be activated without a one character delay.
Rx support functions and operation are quite different from those described for the transmitter. The Rx FIFO receives
data until the number of bytes in the FIFO equals the selected interrupt trigger level. At that time if Rx interrupts are
enabled, the UART will issue an interrupt to the CPU. The Rx FIFO will continue to store bytes until it holds 16 of them.
It will not accept any more data when it is full. Any more data entering the Rx shift register will set the Overrun Error flag.
Normally, the FIFO depth and the programmable trigger levels will give the CPU ample time to empty the Rx FIFO
before an overrun occurs.
One side-effect of having a Rx FIFO is that the selected interrupt trigger level may be above the data level in the FIFO.
This could occur when data at the end of the block contains fewer bytes than the trigger level. No interrupt would be
issued to the CPU and the data would remain in the UART. To prevent the software from having to check for this
situation the chip incorporates a timeout interrupt.
The timeout interrupt is activated when there is a least one byte in the Rx FIFO, and neither the CPU nor the Rx shift
register has accessed the Rx FIFO within 4 character times of the last byte. The timeout interrupt is cleared or reset
when the CPU reads the Rx FIFO or another character enters it.
These FIFO related features allow optimization of CPU/UART transactions and are especially useful given the higher
baud rate capability (256 kbaud).
SMSC DS – LPC47M14X
Page 71
Rev. 03/19/2001
6.7 INFRARED INTERFACE
The infrared interface provides a two-way wireless communications port using infrared as a transmission medium. Two
IR implementations have been provided for the second UART in this chip (logical device 5), IrDA and Amplitude Shift
Keyed IR. The IR transmission can use the standard UART2 TXD2 and RXD2 pins or optional IRTX2 and IRRX2 pins.
These can be selected through the configuration registers.
IrDA 1.0 allows serial communication at baud rates up to 115.2 kbps. Each word is sent serially beginning with a zero
value start bit. A zero is signaled by sending a single IR pulse at the beginning of the serial bit time. A one is signaled
by sending no IR pulse during the bit time. Please refer to the AC timing for the parameters of these pulses and the
IrDA waveform.
The Amplitude Shift Keyed IR allows asynchronous serial communication at baud rates up to 19.2K Baud. Each word is
sent serially beginning with a zero value start bit. A zero is signaled by sending a 500KHz waveform for the duration of
the serial bit time. A one is signaled by sending no transmission during the bit time. Please refer to the AC timing for the
parameters of the ASK-IR waveform.
If the Half Duplex option is chosen, there is a time-out when the direction of the transmission is changed. This time-out
starts at the last bit transferred during a transmission and blocks the receiver input until the timeout expires. If the
transmit buffer is loaded with more data before the time-out expires, the timer is restarted after the new byte is
transmitted. If data is loaded into the transmit buffer while a character is being received, the transmission will not start
until the time-out expires after the last receive bit has been received. If the start bit of another character is received
during this time-out, the timer is restarted after the new character is received. The IR half duplex time-out is
programmable via CRF2 in Logical Device 5. This register allows the time-out to be programmed to any value between 0
and 10msec in 100usec increments.
IR Transmit Pins
The following description pertains to the IRTX and IRTX2 pins of the LPC47M14x.
Following a VTR POR, the IRTX and IRTX2 pins will be output and low. They will remain low until one of the
following conditions are met:IRTX2/GP35 Pin. This pin defaults to the IRTX2 function.
1)
This pin will remain low following a VCC POR until serial port 2 is enabled by setting the activate bit, at which
time the pin will reflect the state of the transmit output of the Serial Port 2 block.
2)
This pin will remain low following a VCC POR until the GPIO output function is selected for the pin, at which
time the pin will reflect the state of the GPIO data bit if it is configured as an output.
GP53/TXD2(IRTX) Pin. This pin defaults to the GPIO output function.
ꢀ
This pin will remain low following a VCC POR until the TXD2 function is selected for the pin AND serial port 2 is
enabled by setting the activate bit, at which time the pin will reflect the state of the transmit output of serial port 2.
Following a VCC POR, setting the TXD2_MODE bit (bit 5 in Serial Port 2 Mode Register, 0xF0 in Logical Device
5 Configuration Registers) to ‘1’ will change the state of the TXD2 pin from low to tristate, regardless of the
function selected on the pin (GPIO of TXD2), regardless of the state of the activate bit for serial port 2 and
regardless of the state of VCC. When VCC is removed from the part while the TXD2_MODE bit is set to ‘1’, the
TXD2 pin will remain tristate unless a VTR POR occurs, which will reset the TXD2_MODE bit.
ꢀ
This pin will remain low following a VCC POR until the corresponding GPIO data bit (GP5 register bit 3) is set or
the polarity bit in the GP53 control register is set.
The TXD2_MODE bit is implemented for modems that do not assert the ring indicator pin when TXD2 is sensed low.
If required, this bit should be used as follows:
ꢀ
ꢀ
ꢀ
When the activate bit for serial port 2 is cleared prior to entering a sleep state, set the TXD2_MODE bit.
When the activate bit for serial port 2 is set, upon exiting a sleep state clear the TXD2_MODE bit.
The IRTX2 pin is not affected by the TXD2_MODE bit.
SMSC DS – LPC47M14X
Page 72
Rev. 03/19/2001
6.8 MPU-401 MIDI UART
6.8.1
Overview
Serial Port 3 is used exclusively in the LPC47M14x as an MPU-401-compatible MIDI Interface. The LPC47M14x
MPU-401 hardware includes a Host Interface, an MPU-401 command controller, configuration registers, and a
compatible UART (FIGURE 3).
Each of these components are discussed in detail, below.
Only the MPU-401 UART (pass-through) mode is included in this implementation. MPU-401 UART mode is
supported on the Sound Blaster 16 Series-compatible MIDI hardware. The Sound Blaster 16 hardware is supported
by Microsoft Windows Operating Systems.
In MPU-401 UART mode, data is transferred without modification between the host and the MIDI device (UART).
Once UART mode is entered using the UART MODE command (3Fh), the only MPU-401 command that the interface
recognizes is RESET (FFh).
MPU-401
COMMAND
CONTROLLER
SA[15:0]
SD[7:0]
nIOW
nIOR
UART
TX
RX
MIDI_OUT
MIDI_IN
HOST
INTERFACE
CONFIGURATION
REGISTERS
IRQ
FIGURE 3 – MPU-401 MIDI INTERFACE
Note: This figure is for illustration purposes only and is not intended to suggest specific implementation
details.
6.8.2
Host Interface
Overview
The Host Interface includes two contiguous 8-bit run-time registers (the Status/Command Port and the Data Port),
and an interrupt. For illustration purposes, the Host Interface block shown in FIGURE 3 uses standard ISA signaling.
Address decoding and interrupt selection for the Host Interface are determined by device configuration registers (see
Section “MPU-401Configuration Registers”).
I/O Addresses
The Sound Blaster 16 MPU-401 UART mode MIDI interface requires two consecutive I/O addresses with possible
base I/O addresses of 300h and 330h. The default is 330h. The LPC47M14x MPU-401 I/O base address is
programmable on even-byte boundaries throughout the entire I/O address range (see Section “Activate and I/O Base
address”).
SMSC DS – LPC47M14X
Page 73
Rev. 03/19/2001
Registers (Ports)
The run-time registers in the MPU-401 Host Interface are shown below in Table 34.
Table 34 – MPU-401 Host Interface Registers
REGISTER NAME
ADDRESS
TYPE
DESCRIPTION
MIDI DATA
MPU-401 I/O Base Address
R/W
Used for MIDI transmit data, MIDI
receive data, and MPU-401 command
acknowledge.
STATUS
MPU-401 I/O Base Address + 1
MPU-401 I/O Base Address + 1
R
Used to indicate the send/receive status
of the MIDI Data port.
Used for MPU-401 Commands.
COMMAND
W
6.8.3
MIDI Data Port
The MIDI Data port exchanges MIDI transmit and MIDI receive data between the MPU-401 UART interface and the
host. The MIDI Data port is read/write (Table 35). The MIDI Data port is also used to return the command
acknowledge byte ‘FEh’ following host writes to the COMMAND port.
The MIDI Data port is full-duplex; i.e., the transmit and receive buffers can be used simultaneously.
An interrupt is generated when either MIDI receive data or a command acknowledge is available to the host in the
MIDI Data register. See Section “Bit 7 – MIDI Receive Buffer Empty” and “Interrupt”
Table 35 – MIDI Data Port
MPU-401 I/O BASE ADDRESS
D7
D6
D5
D4
D3
D2
D1
D0
DEFAULT
TYPE
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
n/a
NAME
MIDI DATA/COMMAND-ACKNOWLEDGE REGISTER
6.8.4
Status Port
The Status port is used to indicate the state of the transmit and receive buffers in the MIDI Data port. The Status port
is read-only (Table 36). Status port Bit 6 is MIDI Transmit Busy, Bit 7 is MIDI Receive Buffer Empty. The remaining
bits in the Status port are RESERVED.
Table 36 – MPU-401 Status Port
MPU-401 I/O BASE ADDRESS+1
D7
R
D6
R
D5
R
D4
R
D3
R
D2
R
D1
R
D0
R
DEFAULT
TYPE
BIT
0x80
MIDI RX MIDI TX
0
0
0
0
0
0
NAME
BUFFE
R
BUSY
EMPTY
Bit 7 – MIDI Receive Buffer Empty
Bit 7 MIDI Receive Buffer Empty indicates the read state of the MIDI Data port (Table 37). If the MRBE bit is ‘0’, MIDI
Read/Command Acknowledge data is available to the host. If the MRBE bit is ‘1’, MIDI Read/Command
Acknowledge data is NOT available to the host.
The MPU-401 Interrupt output is active ‘1’ when the MIDI Receive Buffer Empty bit is ‘0’. The MPU-401 Interrupt
output is inactive ‘0’ when the MIDI Receive Buffer Empty bit is ‘1’. See Section “Interrupt” for more information.
SMSC DS – LPC47M14X
Page 74
Rev. 03/19/2001
Table 37 – MIDI Receive Buffer Empty Status Bit
STATUS PORT
DESCRIPTION
D7
0
MIDI Read/Command Acknowledge data is
available to the host.
MIDI Read/Command Acknowledge data is
NOT available to the host.
1
Bit 6 – MIDI Transmit Busy
Bit 6 MIDI Transmit Busy indicates the send (write) state of the MIDI Data port and Command port (Table 38)
There are no interrupts associated with MIDI transmit (write) data.
Table 38 – MIDI Transmit Busy Status Bit
STATUS PORT
DESCRIPTION
D6
0
The MPU-401 interface is ready to accept a
data/command byte from the host.
The MPU-401 interface is NOT ready to
accept a data/command byte from the host.
1
Bits[5:0]
RESERVED (Reserved bits cannot be written and return ‘0’ when read).
Command Port
The Command port is used to transfer MPU-401 commands to the Command Controller. The Command port is write-
only (Table 39). See Section “MPU-401 Command controller” below.
Table 39 – MPU-401 Command Port
MPU-401 I/O BASE ADDRESS+1
D7
W
D6
W
D5
W
D4
W
D3
W
D2
W
D1
W
D0
W
DEFAULT
TYPE
n/a
NAME
COMMAND REGISTER
Interrupt
The MPU-401 IRQ is asserted (‘1’) when either MIDI receive data or a command acknowledge byte is available tot he
host in the MIDI data register (FIGURE 4). the IRQ is deasserted (‘0’) when the host reads the MIDI Data port.
Note: If, following a host read, data is still available in the 16C550A Receive FIFO, the IRQ will remain asserted (‘1’).
The IRQ is enabled when the ‘Activate’ bit in the MPU-401 configuration registers logical device block is asserted ‘1’.
If the Activate bit is deasserted ‘0’, the MPU-401 IRQ cannot be asserted (see Section “MPU-401 Configuration
Registers”).
The MPU-401 IRQ is not affected by MIDI write data, 16C550A transmit-related functions or Receiver Line Status
interrupts.
The factory default Sound Blaster 16 MPU-401 IRQ is 5.
SMSC DS – LPC47M14X
Page 75
Rev. 03/19/2001
NOTE: IRQ remains asserted
until read FIFO is empty
MIDI_IN
MIDI RX CLOCK4
DATA READY1
IRQ3
MIDI RX DATA BYTE N
MIDI RX DATA BYTE N+1
nREAD2
FIGURE 4 – MPU-401 INTERRUPT
Note1 DATA READY represents the Data Ready bit B0 in the 16C550A UART Line Status Register.
Note2 nREAD represents host read operations from the MIDI Data register.
Note3 IRQ is the MPU-401 Host Interface IRQ shown in FIGURE 3. The 16C550A UART Receive FIFO
Threshold=1.
Note4 MIDI RX CLOCK is the MIDI bit clock. The MIDI bit clock period is 32µs.
6.8.5 MPU-401 Command Controller
Overview
Commands are written by the host to the MPU-401 MIDI Interface through the Command register (Table 34) and are
immediately interpreted by the MPU-401 Command Controller shown in FIGURE 3. The MPU-401 Command
Controller in this implementation only responds to the MPU-401 RESET (FFh) and UART MODE (3Fh) commands.
All other commands are ignored.
Under certain conditions, the Command Controller acknowledges MPU-401 commands with a command
acknowledge byte (FEh).
RESET Command
The RESET command is FFh. The RESET command resets the MPU-401 MIDI Interface. Reset disables the MPU-
401 UART MODE command, disables the 16C550A UART, clears the receive FIFO. The command controller places
the command acknowledge byte ‘FEh’ in the MIDI Data port read buffer if the interface is not in the UART mode.
The RESET command is executed but not acknowledged when the command is received while the interface is in the
UART mode.
When the MPU-401 is reset, receive data from the MIDI_IN port as well as data written by the host to the MIDI Data
port is ignored.
The MPU-401 MIDI Interface is reset following the RESET command or POR.
UART MODE Command
The UART MODE command is 3Fh. The UART MODE command clears the 16C550A transmit and receive FIFOs,
places the command acknowledge byte (FEh) in the MIDI Data port receive buffer, and enables the 16C550A UART
for transmit and receive operations.
In UART mode, the MPU-401 Interface passes MIDI read and write data directly between the host (using the MIDI
Data port) and the 16C550A UART Transmit and Receive buffers.
The MPU-401 Command Controller ignores the UART MODE command when the MPU-401 Interface is already in
UART mode.
The MPU-401 RESET command is executed but not acknowledged by the MPU-401 Command Controller in UART
MODE (see Section “RESET Command”, above).
Command Acknowledge Byte
Under certain conditions, the command controller acknowledges the RESET and UART MODE commands with a
command acknowledge byte (FEh).
The command acknowledge byte appears as read-data in the MIDI Data port.
Note: The command acknowledge byte will appear as the next available data byte in the receive buffer of the MIDI
Data port. For example if the receive FIFO is not empty when an MPU-401 RESET command is received, the
SMSC DS – LPC47M14X
Page 76
Rev. 03/19/2001
command acknowledge will appear first, before any unread FIFO data. In the examples above, the receive FIFO is
cleared before the command acknowledge byte is placed in the MIDI Data port read buffer.
6.8.6
MIDI UART
Overview
The UART is used to transmit and receive MIDI protocol data from the MIDI Data port in the Host Interface (see
Section “Host Interface”).
The MIDI protocol requires 31.25k Baud (±1%) and 10 bits total per frame: 1 start bit, 8 data bits, no parity, and 1
stop bit. For example, there are 320 microseconds per serial MIDI data byte. MIDI data is transferred LSB first
(Figure 7).
The UART is configured in full-duplex mode for the MPU-401 MIDI Interface, with 16-byte send/receive FIFOs.
MIDI RX DATA BYTE (01H)
MIDI RX CLOCK1
MIDI_IN
FIGURE 5 - MIDI DATA BYTE EXAMPLE
Note1: MIDI RX CLOCK is the MIDI bit clock. The MIDI bit clock period is 32µs.
6.8.7
MPU-401 Configuration Registers
The LPC47M14x configuration registers are in Logical Device B (see “Configuration” section). The configuration
registers contain the MPU-401 Activate, Base Address and Interrupt select. The defaults for the Base Address and
Interrupt Select configuration registers match the MPU-401 factory defaults.
Activate and I/O Base Address
When the Activate bit D0 is ‘0’, the MPU-401 I/O base address decoder is disabled, the IRQ is always deasserted,
and the MPU-401 hardware is in a minimum power-consumption state. When the Activate bit is ‘1’, the MPU-401 I/O
base address decoder and the IRQ are enabled, and the MPU-401 hardware is fully powered.
Register 0x60 is the MPU-401 I/O Base Address High Byte, register 0x61 is the MPU-401 I/O Base Address Low
Byte. The MPU-401 I/O base address is programmable on even-byte boundaries. The valid MPU-401 I/O base
address range is 0x0100 – 0x0FFE. See Section “Host Interface”.
SMSC DS – LPC47M14X
Page 77
Rev. 03/19/2001
6.9 PARALLEL PORT
The LPC47M14x incorporates an IBM XT/AT compatible parallel port. This supports the optional PS/2 type bi-directional
parallel port (SPP), the Enhanced Parallel Port (EPP) and the Extended Capabilities Port (ECP) parallel port modes.
Refer to the Configuration Registers for information on disabling, power down, changing the base address of the parallel
port, and selecting the mode of operation.
The parallel port also incorporates SMSC's ChiProtect circuitry, which prevents possible damage to the parallel port due
to printer power-up.
The functionality of the Parallel Port is achieved through the use of eight addressable ports, with their associated
registers and control gating. The control and data port are read/write by the CPU, the status port is read/write in the EPP
mode. The address map of the Parallel Port is shown below:
DATA PORT
BASE ADDRESS + 00H
BASE ADDRESS + 01H
BASE ADDRESS + 02H
BASE ADDRESS + 03H
EPP DATA PORT 0
EPP DATA PORT 1
EPP DATA PORT 2
EPP DATA PORT 3
BASE ADDRESS + 04H
BASE ADDRESS + 05H
BASE ADDRESS + 06H
BASE ADDRESS + 07H
STATUS PORT
CONTROL PORT
EPP ADDR PORT
The bit map of these registers is:
D0
PD0
TMOUT
D1
PD1
0
D2
PD2
0
D3
PD3
nERR
D4
PD4
SLCT
D5
PD5
PE
D6
PD6
nACK nBUSY
D7
PD7
NOTE
1
1
DATA PORT
STATUS
PORT
CONTROL
PORT
STROBE AUTOFD nINIT
SLC
PD3
PD3
PD3
PD3
PD3
IRQE
PD4
PD4
PD4
PD4
PD4
PCD
PD5
PD5
PD5
PD5
PD5
0
0
1
2
2
2
2
2
EPP ADDR
PD0
PD0
PD0
PD0
PD0
PD1
PD1
PD1
PD1
PD1
PD2
PD2
PD2
PD2
PD2
PD6
PD6
PD6
PD6
PD6
PD7
PD7
PD7
PD7
PD7
PORT
EPP DATA
PORT 0
EPP DATA
PORT 1
EPP DATA
PORT 2
EPP DATA
PORT 3
Note 1: These registers are available in all modes.
Note 2: These registers are only available in EPP mode.
SMSC DS – LPC47M14X
Page 78
Rev. 03/19/2001
Table 40 – Parallel Port Connector
HOST
CONNECTOR
PIN NUMBER
STANDARD
nStrobe
PData<0:7>
nAck
Busy
PE
EPP
ECP
1
83
68-75
80
79
78
nWrite
nStrobe
2-9
10
11
12
PData<0:7>
Intr
PData<0:7>
nAck
Busy, PeriphAck(3)
nWait
(User Defined)
PError,
nAckReverse (3)
13
14
77
82
Select
nAutoFd
(User Defined)
nDatastb
Select
nAutoFd,
HostAck(3)
15
16
17
81
66
67
nError
nInit
(User Defined)
nRESET
nFault (1)
nPeriphRequest (3)
nInit(1)
nReverseRqst(3)
nSelectIn
nAddrstrb
nSelectIn(1,3)
(1) = Compatible Mode
(3) = High Speed Mode
Note: For the cable interconnection required for ECP support and the Slave Connector pin numbers, refer to the
IEEE 1284 Extended Capabilities Port Protocol and ISA Standard, Rev. 1.14, July 14, 1993. This document is
available from Microsoft.
6.9.1
IBM XT/AT Compatible, Bi-Directional and EPP Modes
DATA PORT
ADDRESS OFFSET = 00H
The Data Port is located at an offset of '00H' from the base address. The data register is cleared at initialization by
RESET. During a WRITE operation, the Data Register latches the contents of the internal data bus. The contents of
this register are buffered (non inverting) and output onto the PD0 - PD7 ports. During a READ operation in SPP mode,
PD0 - PD7 ports are buffered (not latched) and output to the host CPU.
STATUS PORT
ADDRESS OFFSET = 01H
The Status Port is located at an offset of '01H' from the base address. The contents of this register are latched for the
duration of a read cycle. The bits of the Status Port are defined as follows:
BIT 0 TMOUT - TIME OUT
This bit is valid in EPP mode only and indicates that a 10 usec time out has occurred on the EPP bus. A logic O means
that no time out error has occurred; a logic 1 means that a time out error has been detected. This bit is cleared by a
RESET. If the TIMEOUT_SELECT bit (bit 4 of the Parallel Port Mode Register 2, 0xF1 in Logical Device 3 Configuration
Registers) is ‘0’, writing a one to this bit clears the TMOUT status bit. Writing a zero to this bit has no effect. If the
TIMEOUT_SELECT bit (bit 4 of the Parallel Port Mode Register 2, 0xF1 in Logical Device 3 Configuration Registers) is
‘1’, the TMOUT bit is cleared on the trailing edge of a read of the EPP Status Register.
BITS 1, 2 - are not implemented as register bits, during a read of the Printer Status Register these bits are a low level.
BIT 3 nERR – nERROR
The level on the nERROR input is read by the CPU as bit 3 of the Printer Status Register. A logic 0 means an error has
been detected; a logic 1 means no error has been detected.
BIT 4 SLCT - PRINTER SELECTED STATUS
The level on the SLCT input is read by the CPU as bit 4 of the Printer Status Register. A logic 1 means the printer is on
line; a logic 0 means it is not selected.
SMSC DS – LPC47M14X
Page 79
Rev. 03/19/2001
BIT 5 PE - PAPER END
The level on the PE input is read by the CPU as bit 5 of the Printer Status Register. A logic 1 indicates a paper end; a
logic 0 indicates the presence of paper.
BIT 6 nACK - ACKNOWLEDGE
The level on the nACK input is read by the CPU as bit 6 of the Printer Status Register. A logic 0 means that the printer
has received a character and can now accept another. A logic 1 means that it is still processing the last character or has
not received the data.
BIT 7 nBUSY - nBUSY
The complement of the level on the BUSY input is read by the CPU as bit 7 of the Printer Status Register. A logic 0 in
this bit means that the printer is busy and cannot accept a new character. A logic 1 means that it is ready to accept the
next character.
CONTROL PORT
ADDRESS OFFSET = 02H
The Control Port is located at an offset of '02H' from the base address. The Control Register is initialized by the RESET
input, bits 0 to 5 only being affected; bits 6 and 7 are hard wired low.
BIT 0 STROBE - STROBE
This bit is inverted and output onto the nSTROBE output.
BIT 1 AUTOFD - AUTOFEED
This bit is inverted and output onto the nAutoFd output. A logic 1 causes the printer to generate a line feed after each
line is printed. A logic 0 means no autofeed.
BIT 2 nINIT - INITIATE OUTPUT
This bit is output onto the nINIT output without inversion.
BIT 3 SLCTIN - PRINTER SELECT INPUT
This bit is inverted and output onto the nSLCTIN output. A logic 1 on this bit selects the printer; a logic 0 means the
printer is not selected.
BIT 4 IRQE - INTERRUPT REQUEST ENABLE
The interrupt request enable bit when set to a high level may be used to enable interrupt requests from the Parallel Port
to the CPU. An interrupt request is generated on the IRQ port by a positive going nACK input. When the IRQE bit is
programmed low the IRQ is disabled.
BIT 5 PCD - PARALLEL CONTROL DIRECTION
Parallel Control Direction is not valid in printer mode. In printer mode, the direction is always out regardless of the state
of this bit. In bi-directional, EPP or ECP mode, a logic 0 means that the printer port is in output mode (write); a logic 1
means that the printer port is in input mode (read).
Bits 6 and 7 during a read are a low level, and cannot be written.
EPP ADDRESS PORT
ADDRESS OFFSET = 03H
The EPP Address Port is located at an offset of '03H' from the base address. The address register is cleared at
initialization by RESET. During a WRITE operation, the contents of the internal data bus DB0-DB7 are buffered (non
inverting) and output onto the PD0 - PD7 ports. An LPC I/O write cycle causes an EPP ADDRESS WRITE cycle to be
performed, during which the data is latched for the duration of the EPP write cycle. During a READ operation, PD0 -
PD7 ports are read. An LPC I/O read cycle causes an EPP ADDRESS READ cycle to be performed and the data
output to the host CPU, the deassertion of ADDRSTB latches the PData for the duration of the read cycle. This register
is only available in EPP mode.
EPP DATA PORT 0
ADDRESS OFFSET = 04H
The EPP Data Port 0 is located at an offset of '04H' from the base address. The data register is cleared at initialization
by RESET. During a WRITE operation, the contents of the internal data bus DB0-DB7 are buffered (non inverting) and
output onto the PD0 - PD7 ports. An LPC I/O write cycle causes an EPP DATA WRITE cycle to be performed, during
which the data is latched for the duration of the EPP write cycle. During a READ operation, PD0 - PD7 ports are read.
An LPC I/O read cycle causes an EPP READ cycle to be performed and the data output to the host CPU, the
deassertion of DATASTB latches the PData for the duration of the read cycle. This register is only available in EPP
mode.
SMSC DS – LPC47M14X
Page 80
Rev. 03/19/2001
EPP DATA PORT 1
ADDRESS OFFSET = 05H
The EPP Data Port 1 is located at an offset of '05H' from the base address. Refer to EPP DATA PORT 0 for a
description of operation. This register is only available in EPP mode.
EPP DATA PORT 2
ADDRESS OFFSET = 06H
The EPP Data Port 2 is located at an offset of '06H' from the base address. Refer to EPP DATA PORT 0 for a
description of operation. This register is only available in EPP mode.
EPP DATA PORT 3
ADDRESS OFFSET = 07H
The EPP Data Port 3 is located at an offset of '07H' from the base address. Refer to EPP DATA PORT 0 for a
description of operation. This register is only available in EPP mode.
EPP 1.9 OPERATION
When the EPP mode is selected in the configuration register, the standard and bi-directional modes are also available. If
no EPP Read, Write or Address cycle is currently executing, then the PDx bus is in the standard or bi-directional mode,
and all output signals (STROBE, AUTOFD, INIT) are as set by the SPP Control Port and direction is controlled by PCD
of the Control port.
In EPP mode, the system timing is closely coupled to the EPP timing. For this reason, a watchdog timer is required to
prevent system lockup. The timer indicates if more than 10usec have elapsed from the start of the EPP cycle to nWAIT
being deasserted (after command). If a time-out occurs, the current EPP cycle is aborted and the time-out condition is
indicated in Status bit 0.
During an EPP cycle, if STROBE is active, it overrides the EPP write signal forcing the PDx bus to always be in a write
mode and the nWRITE signal to always be asserted.
Software Constraints
Before an EPP cycle is executed, the software must ensure that the control register bit PCD is a logic "0" (i.e., a 04H or
05H should be written to the Control port). If the user leaves PCD as a logic "1", and attempts to perform an EPP write,
the chip is unable to perform the write (because PCD is a logic "1") and will appear to perform an EPP read on the
parallel bus, no error is indicated.
EPP 1.9 Write
The timing for a write operation (address or data) is shown in timing diagram EPP Write Data or Address cycle. The
chip inserts wait states into the LPC I/O write cycle until it has been determined that the write cycle can complete. The
write cycle can complete under the following circumstances:
1)
If the EPP bus is not ready (nWAIT is active low) when nDATASTB or nADDRSTB goes active then the
write can complete when nWAIT goes inactive high.
2)
If the EPP bus is ready (nWAIT is inactive high) then the chip must wait for it to go active low before
changing the state of nDATASTB, nWRITE or nADDRSTB. The write can complete once nWAIT is
determined inactive.
Write Sequence of Operation
1) The host initiates an I/O write cycle to the selected EPP register.
2) If WAIT is not asserted, the chip must wait until WAIT is asserted.
3) The chip places address or data on PData bus, clears PDIR, and asserts nWRITE.
4) Chip asserts nDATASTB or nADDRSTRB indicating that PData bus contains valid information, and the WRITE
signal is valid.
5) Peripheral deasserts nWAIT, indicating that any setup requirements have been satisfied and the chip may
begin the termination phase of the cycle.
6) a) The chip deasserts nDATASTB or nADDRSTRB, this marks the beginning of the termination phase. If it
has not already done so, the peripheral should latch the information byte now.
b) The chip latches the data from the internal data bus for the PData bus and drives the sync that indicates
that no more wait states are required followed by the TAR to complete the write cycle.
7) Peripheral asserts nWAIT, indicating to the host that any hold time requirements have been satisfied and
acknowledging the termination of the cycle.
8) Chip may modify nWRITE and nPDATA in preparation for the next cycle.
SMSC DS – LPC47M14X
Page 81
Rev. 03/19/2001
EPP 1.9 Read
The timing for a read operation (data) is shown in timing diagram EPP Read Data cycle. The chip inserts wait states into
the LPC I/O read cycle until it has been determined that the read cycle can complete. The read cycle can complete
under the following circumstances:
1) If the EPP bus is not ready (nWAIT is active low) when nDATASTB goes active then the read can complete
when nWAIT goes inactive high.
2) If the EPP bus is ready (nWAIT is inactive high) then the chip must wait for it to go active low before changing
the state of nWRITE or before nDATASTB goes active. The read can complete once nWAIT is determined
inactive.
Read Sequence of Operation
1) The host initiates an I/O read cycle to the selected EPP register.
2) If WAIT is not asserted, the chip must wait until WAIT is asserted.
3) The chip tri-states the PData bus and deasserts nWRITE.
4) Chip asserts nDATASTB or nADDRSTRB indicating that PData bus is tri-stated, PDIR is set and the nWRITE
signal is valid.
5) Peripheral drives PData bus valid.
6) Peripheral deasserts nWAIT, indicating that PData is valid and the chip may begin the termination phase of the
cycle.
7) a) The chip latches the data from the PData bus for the internal data bus and deasserts nDATASTB or
nADDRSTRB. This marks the beginning of the termination phase.
b) The chip drives the sync that indicates that no more wait states are required and drives the valid data onto
the LAD[3:0] signals, followed by the TAR to complete the read cycle.
8) Peripheral tri-states the PData bus and asserts nWAIT, indicating to the host that the PData bus is tri-stated.
9) Chip may modify nWRITE, PDIR and nPDATA in preparation for the next cycle.
EPP 1.7 OPERATION
When the EPP 1.7 mode is selected in the configuration register, the standard and bi-directional modes are also
available. If no EPP Read, Write or Address cycle is currently executing, then the PDx bus is in the standard or bi-
directional mode, and all output signals (STROBE, AUTOFD, INIT) are as set by the SPP Control Port and direction is
controlled by PCD of the Control port.
In EPP mode, the system timing is closely coupled to the EPP timing. For this reason, a watchdog timer is required to
prevent system lockup. The timer indicates if more than 10usec have elapsed from the start of the EPP cycle to the end
of the cycle. If a time-out occurs, the current EPP cycle is aborted and the time-out condition is indicated in Status bit 0.
Software Constraints
Before an EPP cycle is executed, the software must ensure that the control register bits D0, D1 and D3 are set to zero.
Also, bit D5 (PCD) is a logic "0" for an EPP write or a logic "1" for and EPP read.
EPP 1.7 Write
The timing for a write operation (address or data) is shown in timing diagram EPP 1.7 Write Data or Address cycle. The
chip inserts wait states into the I/O write cycle when nWAIT is active low during the EPP cycle. This can be used to
extend the cycle time. The write cycle can complete when nWAIT is inactive high.
Write Sequence of Operation
1) The host sets PDIR bit in the control register to a logic "0". This asserts nWRITE.
2) The host initiates an I/O write cycle to the selected EPP register.
3) The chip places address or data on PData bus.
4) Chip asserts nDATASTB or nADDRSTRB indicating that PData bus contains valid information, and the WRITE
signal is valid.
5) If nWAIT is asserted, the chip inserts wait states into I/O write cycle until the peripheral deasserts nWAIT or a
time-out occurs.
6) The chip drives the final sync, deasserts nDATASTB or nADDRSTRB and latches the data from the internal
data bus for the PData bus.
7) Chip may modify nWRITE, PDIR and nPDATA in preparation of the next cycle.
SMSC DS – LPC47M14X
Page 82
Rev. 03/19/2001
EPP 1.7 Read
The timing for a read operation (data) is shown in timing diagram EPP 1.7 Read Data cycle. The chip inserts wait states
into the I/O read cycle when nWAIT is active low during the EPP cycle. This can be used to extend the cycle time. The
read cycle can complete when nWAIT is inactive high.
Read Sequence of Operation
1) The host sets PDIR bit in the control register to a logic "1". This deasserts nWRITE and tri-states the PData
bus.
2) The host initiates an I/O read cycle to the selected EPP register.
3) Chip asserts nDATASTB or nADDRSTRB indicating that PData bus is tri-stated, PDIR is set and the nWRITE
signal is valid.
4) If nWAIT is asserted, the chip inserts wait states into the I/O read cycle until the peripheral deasserts nWAIT or
a time-out occurs.
5) The Peripheral drives PData bus valid.
6) The Peripheral deasserts nWAIT, indicating that PData is valid and the chip may begin the termination phase
of the cycle.
7) The chip drives the final sync and deasserts nDATASTB or nADDRSTRB.
8) Peripheral tri-states the PData bus.
9) Chip may modify nWRITE, PDIR and nPDATA in preparation of the next cycle.
Table 41 – EPP Pin Descriptions
EPP
SIGNAL
nWRITE
PD<0:7>
INTR
EPP NAME
nWrite
Address/Data
Interrupt
TYPE
EPP DESCRIPTION
This signal is active low. It denotes a write operation.
Bi-directional EPP byte wide address and data bus.
This signal is active high and positive edge triggered. (Pass
through with no inversion, Same as SPP).
O
I/O
I
nWAIT
nWait
I
This signal is active low. It is driven inactive as a positive
acknowledgement from the device that the transfer of data is
completed. It is driven active as an indication that the device is
ready for the next transfer.
nDATASTB nData Strobe
nRESET nReset
O
O
O
This signal is active low. It is used to denote data read or write
operation.
This signal is active low. When driven active, the EPP device
is reset to its initial operational mode.
This signal is active low. It is used to denote address read or
write operation.
nADDRSTB Address
Strobe
PE
SLCT
Paper End
I
I
Same as SPP mode.
Same as SPP mode.
Printer
Selected
Status
nERR
Error
I
Same as SPP mode.
Note 1: SPP and EPP can use 1 common register.
Note 2: nWrite is the only EPP output that can be over-ridden by SPP control port during an EPP cycle. For correct
EPP read cycles, PCD is required to be a low.
SMSC DS – LPC47M14X
Page 83
Rev. 03/19/2001
6.9.2
Extended Capabilities Parallel Port
ECP provides a number of advantages, some of which are listed below. The individual features are explained in greater
detail in the remainder of this section.
High performance half-duplex forward and reverse channel Interlocked handshake, for fast reliable transfer Optional
single byte RLE compression for improved throughput (64:1) Channel addressing for low-cost peripherals Maintains link
and data layer separation Permits the use of active output drivers permits the use of adaptive signal timing Peer-to-peer
capability.
Vocabulary
The following terms are used in this document:
assert:
When a signal asserts it transitions to a "true" state, when a signal deasserts it transitions to a "false"
state.
forward: Host to Peripheral communication.
reverse: Peripheral to Host communication
Pword:
A port word; equal in size to the width of the LPC interface. For this implementation, PWord is always
8 bits.
1
0
A high level.
A low level.
These terms may be considered synonymous:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
PeriphClk, nAck
HostAck, nAutoFd
PeriphAck, Busy
nPeriphRequest, nFault
nReverseRequest, nInit
nAckReverse, PError
Xflag, Select
ECPMode, nSelectln
HostClk, nStrobe
Reference Document: IEEE 1284 Extended Capabilities Port Protocol and ISA Interface Standard, Rev 1.14, July 14,
1993. This document is available from Microsoft.
The bit map of the Extended Parallel Port registers is:
D7
PD7
D6
PD6
D5
PD5
D4
PD4
D3
PD3
D2
PD2
D1
PD1
D0
PD0
NOTE
data
ecpAFifo
dsr
dcr
Addr/RLE
nBusy
0
Address or RLE field
Select nFault
Direction ackIntEn SelectI
n
2
1
1
nAck
0
PError
0
nInit
0
0
autofd strobe
cFifo
ecpDFifo
tFifo
Parallel Port Data FIFO
ECP Data FIFO
Test FIFO
2
2
2
cnfgA
cnfgB
ecr
0
0
0
1
0
0
0
0
compress
intrValue
MODE
Parallel Port IRQ
Parallel Port DMA
nErrIntrEn dmaEn serviceIntr
full
empty
Note 1: These registers are available in all modes.
Note 2: All FIFOs use one common 16 byte FIFO.
Note 3: The ECP Parallel Port Config Reg B reflects the IRQ and DMA channel selected by the Configuration
Registers.
SMSC DS – LPC47M14X
Page 84
Rev. 03/19/2001
ECP IMPLEMENTATION STANDARD
This specification describes the standard interface to the Extended Capabilities Port (ECP). All LPC devices supporting
ECP must meet the requirements contained in this section or the port will not be supported by Microsoft. For a
description of the ECP Protocol, please refer to the IEEE 1284 Extended Capabilities Port Protocol and ISA Interface
Standard, Rev. 1.14, July 14, 1993. This document is available from Microsoft.
Description
The port is software and hardware compatible with existing parallel ports so that it may be used as a standard LPT port if
ECP is not required. The port is designed to be simple and requires a small number of gates to implement. It does not
do any "protocol" negotiation, rather it provides an automatic high burst-bandwidth channel that supports DMA for ECP
in both the forward and reverse directions.
Small FIFOs are employed in both forward and reverse directions to smooth data flow and improve the maximum
bandwidth requirement. The size of the FIFO is 16 bytes deep. The port supports an automatic handshake for the
standard parallel port to improve compatibility mode transfer speed.
The port also supports run length encoded (RLE) decompression (required) in hardware. Compression is
accomplished by counting identical bytes and transmitting an RLE byte that indicates how many times the next byte is
to be repeated. Decompression simply intercepts the RLE byte and repeats the following byte the specified number of
times. Hardware support for compression is optional.
Table 42 – ECP Pin Descriptions
NAME
nStrobe
TYPE
DESCRIPTION
O
During write operations nStrobe registers data or address into the slave on
the asserting edge (handshakes with Busy).
PData 7:0
nAck
I/O
I
Contains address or data or RLE data.
Indicates valid data driven by the peripheral when asserted. This signal
handshakes with nAutoFd in reverse.
PeriphAck (Busy)
I
I
This signal deasserts to indicate that the peripheral can accept data. This
signal handshakes with nStrobe in the forward direction. In the reverse
direction this signal indicates whether the data lines contain ECP
command information or data. The peripheral uses this signal to flow
control in the forward direction. It is an "interlocked" handshake with
nStrobe. PeriphAck also provides command information in the reverse
direction.
PError
Used to acknowledge a change in the direction the transfer (asserted =
(nAckReverse)
forward).
The peripheral drives this signal low to acknowledge
nReverseRequest. It is an "interlocked" handshake with nReverseRequest.
The host relies upon nAckReverse to determine when it is permitted to
drive the data bus.
Select
nAutoFd
(HostAck)
I
O
Indicates printer on line.
Requests a byte of data from the peripheral when asserted, handshaking
with nAck in the reverse direction. In the forward direction this signal
indicates whether the data lines contain ECP address or data. The host
drives this signal to flow control in the reverse direction. It is an
"interlocked" handshake with nAck. HostAck also provides command
information in the forward phase.
Generates an error interrupt when asserted. This signal provides a
mechanism for peer-to-peer communication. This signal is valid only in the
forward direction. During ECP Mode the peripheral is permitted (but not
required) to drive this pin low to request a reverse transfer. The request is
merely a "hint" to the host; the host has ultimate control over the transfer
direction. This signal would be typically used to generate an interrupt to
the host CPU.
nFault
I
(nPeriphRequest)
nInit
O
O
Sets the transfer direction (asserted = reverse, deasserted = forward).
This pin is driven low to place the channel in the reverse direction. The
peripheral is only allowed to drive the bi-directional data bus while in ECP
Mode and HostAck is low and nSelectIn is high.
nSelectIn
Always deasserted in ECP mode.
SMSC DS – LPC47M14X
Page 85
Rev. 03/19/2001
Register Definitions
The register definitions are based on the standard IBM addresses for LPT. All of the standard printer ports are
supported. The additional registers attach to an upper bit decode of the standard LPT port definition to avoid conflict
with standard ISA devices. The port is equivalent to a generic parallel port interface and may be operated in that mode.
The port registers vary depending on the mode field in the ecr. The table below lists these dependencies. Operation of
the devices in modes other that those specified is undefined.
Table 43 – ECP Register Definitions
NAME
ADDRESS (Note 1)
+000h R/W
+000h R/W
+001h R/W
+002h R/W
+400h R/W
+400h R/W
+400h R/W
+400h R
ECP MODES
FUNCTION
Data Register
ECP FIFO (Address)
Status Register
data
000-001
011
All
ecpAFifo
dsr
dcr
All
Control Register
cFifo
ecpDFifo
tFifo
cnfgA
cnfgB
ecr
010
011
110
111
111
All
Parallel Port Data FIFO
ECP FIFO (DATA)
Test FIFO
Configuration Register A
Configuration Register B
Extended Control Register
+401h R/W
+402h R/W
Note 1: These addresses are added to the parallel port base address as selected by configuration register or jumpers.
Note 2: All addresses are qualified with AEN. Refer to the AEN pin definition.
Table 44 – Mode Descriptions
MODE
000
001
010
011
100
101
110
111
DESCRIPTION*
SPP mode
PS/2 Parallel Port mode
Parallel Port Data FIFO mode
ECP Parallel Port mode
EPP mode (If this option is enabled in the configuration registers)
Reserved
Test mode
Configuration mode
*Refer to ECR Register Description
SMSC DS – LPC47M14X
Page 86
Rev. 03/19/2001
DATA and ECPAFIFO PORT
ADDRESS OFFSET = 00H
Modes 000 and 001 (Data Port)
The Data Port is located at an offset of '00H' from the base address. The data register is cleared at initialization by
RESET. During a WRITE operation, the Data Register latches the contents of the data bus. The contents of this
register are buffered (non inverting) and output onto the PD0 - PD7 ports. During a READ operation, PD0 - PD7 ports
are read and output to the host CPU.
Mode 011 (ECP FIFO - Address/RLE)
A data byte written to this address is placed in the FIFO and tagged as an ECP Address/RLE. The hardware at the ECP
port transmits this byte to the peripheral automatically. The operation of this register is only defined for the forward
direction (direction is 0). Refer to the ECP Parallel Port Forward Timing Diagram, located in the Timing Diagrams
section of this data sheet .
DEVICE STATUS REGISTER (DSR)
ADDRESS OFFSET = 01H
The Status Port is located at an offset of '01H' from the base address. Bits 0 - 2 are not implemented as register bits,
during a read of the Printer Status Register these bits are a low level. The bits of the Status Port are defined as follows:
BIT 3 nFault
The level on the nFault input is read by the CPU as bit 3 of the Device Status Register.
BIT 4 Select
The level on the Select input is read by the CPU as bit 4 of the Device Status Register.
BIT 5 PError
The level on the PError input is read by the CPU as bit 5 of the Device Status Register. Printer Status Register.
BIT 6 nAck
The level on the nAck input is read by the CPU as bit 6 of the Device Status Register.
BIT 7 nBusy
The complement of the level on the BUSY input is read by the CPU as bit 7 of the Device Status Register.
DEVICE CONTROL REGISTER (DCR)
ADDRESS OFFSET = 02H
The Control Register is located at an offset of '02H' from the base address. The Control Register is initialized to zero by
the RESET input, bits 0 to 5 only being affected; bits 6 and 7 are hard wired low.
BIT 0 STROBE - STROBE
This bit is inverted and output onto the nSTROBE output.
BIT 1 AUTOFD - AUTOFEED
This bit is inverted and output onto the nAutoFd output. A logic 1 causes the printer to generate a line feed after each
line is printed. A logic 0 means no autofeed.
BIT 2 nINIT - INITIATE OUTPUT
This bit is output onto the nINIT output without inversion.
BIT 3 SELECTIN
This bit is inverted and output onto the nSLCTIN output. A logic 1 on this bit selects the printer; a logic 0 means the
printer is not selected.
BIT 4 ACKINTEN - INTERRUPT REQUEST ENABLE
The interrupt request enable bit when set to a high level may be used to enable interrupt requests from the Parallel
Port to the CPU due to a low to high transition on the nACK input. Refer to the description of the interrupt under
Operation, Interrupts.
BIT 5 DIRECTION
If mode=000 or mode=010, this bit has no effect and the direction is always out regardless of the state of this bit. In all
other modes, Direction is valid and a logic 0 means that the printer port is in output mode (write); a logic 1 means that
the printer port is in input mode (read).
SMSC DS – LPC47M14X
Page 87
Rev. 03/19/2001
BITS 6 and 7 during a read are a low level, and cannot be written.
CFIFO (Parallel Port Data FIFO)
ADDRESS OFFSET = 400h
Mode = 010
Bytes written or DMAed from the system to this FIFO are transmitted by a hardware handshake to the peripheral using
the standard parallel port protocol. Transfers to the FIFO are byte aligned. This mode is only defined for the forward
direction.
ECPDFIFO (ECP Data FIFO)
ADDRESS OFFSET = 400H
Mode = 011
Bytes written or DMAed from the system to this FIFO, when the direction bit is 0, are transmitted by a hardware
handshake to the peripheral using the ECP parallel port protocol. Transfers to the FIFO are byte aligned.
Data bytes from the peripheral are read under automatic hardware handshake from ECP into this FIFO when the
direction bit is 1. Reads or DMAs from the FIFO will return bytes of ECP data to the system.
TFIFO (Test FIFO Mode)
ADDRESS OFFSET = 400H
Mode = 110
Data bytes may be read, written or DMAed to or from the system to this FIFO in any direction. Data in the tFIFO will not
be transmitted to the to the parallel port lines using a hardware protocol handshake. However, data in the tFIFO may be
displayed on the parallel port data lines.
The tFIFO will not stall when overwritten or underrun. If an attempt is made to write data to a full tFIFO, the new data is
not accepted into the tFIFO. If an attempt is made to read data from an empty tFIFO, the last data byte is re-read again.
The full and empty bits must always keep track of the correct FIFO state. The tFIFO will transfer data at the maximum
ISA rate so that software may generate performance metrics.
The FIFO size and interrupt threshold can be determined by writing bytes to the FIFO and checking the full and
serviceIntr bits.
The writeIntrThreshold can be determined by starting with a full tFIFO, setting the direction bit to 0 and emptying it a byte
at a time until serviceIntr is set. This may generate a spurious interrupt, but will indicate that the threshold has been
reached.
The readIntrThreshold can be determined by setting the direction bit to 1 and filling the empty tFIFO a byte at a time until
serviceIntr is set. This may generate a spurious interrupt, but will indicate that the threshold has been reached.
Data bytes are always read from the head of tFIFO regardless of the value of the direction bit. For example if 44h, 33h,
22h is written to the FIFO, then reading the tFIFO will return 44h, 33h, 22h in the same order as was written.
CNFGA (Configuration Register A)
ADDRESS OFFSET = 400H
Mode = 111
This register is a read only register. When read, 10H is returned. This indicates to the system that this is an 8-bit
implementation. (PWord = 1 byte)
CNFGB (Configuration Register B)
ADDRESS OFFSET = 401H
Mode = 111
BIT 7 Compress
This bit is read only. During a read it is a low level. This means that this chip does not support hardware RLE
compression. It does support hardware de-compression.
SMSC DS – LPC47M14X
Page 88
Rev. 03/19/2001
BIT 6 intrValue
Returns the value of the interrupt to determine possible conflicts.
BIT [5:3] Parallel Port IRQ (read-only)
to Table 45B
BITS [2:0] Parallel Port DMA (read-only)
to Table 45C
ECR (Extended Control Register)
ADDRESS OFFSET = 402H
Mode = all
This register controls the extended ECP parallel port functions.
BITS 7,6,5
These bits are Read/Write and select the Mode.
BIT 4 nErrIntrEn
Read/Write (Valid only in ECP Mode)
1: Disables the interrupt generated on the asserting edge of nFault.
0: Enables an interrupt pulse on the high to low edge of nFault. Note that an interrupt will be generated if nFault is
asserted (interrupting) and this bit is written from a 1 to a 0. This prevents interrupts from being lost in the time
between the read of the ecr and the write of the ecr.
BIT 3 dmaEn
Read/Write
1: Enables DMA (DMA starts when serviceIntr is 0).
0: Disables DMA unconditionally.
BIT 2 serviceIntr
Read/Write
1: Disables DMA and all of the service interrupts.
0: Enables one of the following 3 cases of interrupts. Once one of the 3 service interrupts has occurred serviceIntr bit
shall be set to a 1 by hardware. It must be reset to 0 to re-enable the interrupts. Writing this bit to a 1 will not cause
an interrupt.
case dmaEn=1:
During DMA (this bit is set to a 1 when terminal count is reached).
case dmaEn=0 direction=0:
This bit shall be set to 1 whenever there are writeIntrThreshold or more bytes free in the FIFO.
case dmaEn=0 direction=1:
This bit shall be set to 1 whenever there are readIntrThreshold or more valid bytes to be read from the FIFO.
BIT 1 full
Read only
1: The FIFO cannot accept another byte or the FIFO is completely full.
0: The FIFO has at least 1 free byte.
BIT 0 empty
Read only
1: The FIFO is completely empty.
0: The FIFO contains at least 1 byte of data.
SMSC DS – LPC47M14X
Page 89
Rev. 03/19/2001
Table 45a – Extended Control Register
MODE
R/W
000: Standard Parallel Port Mode . In this mode the FIFO is reset and common collector drivers are
used on the control lines (nStrobe, nAutoFd, nInit and nSelectIn). Setting the direction bit will
not tri-state the output drivers in this mode.
001: PS/2 Parallel Port Mode. Same as above except that direction may be used to tri-state the
data lines and reading the data register returns the value on the data lines and not the value in
the data register. All drivers have active pull-ups (push-pull).
010: Parallel Port FIFO Mode. This is the same as 000 except that bytes are written or DMAed to the
FIFO. FIFO data is automatically transmitted using the standard parallel port protocol. Note that
this mode is only useful when direction is 0. All drivers have active pull-ups (push-pull).
011: ECP Parallel Port Mode. In the forward direction (direction is 0) bytes placed into the ecpDFifo
and bytes written to the ecpAFifo are placed in a single FIFO and transmitted automatically to
the peripheral using ECP Protocol. In the reverse direction (direction is 1) bytes are moved
from the ECP parallel port and packed into bytes in the ecpDFifo. All drivers have active
pull-ups (push-pull).
100: Selects EPP Mode: In this mode, EPP is selected if the EPP supported option is selected in
configuration register L3-CRF0. All drivers have active pull-ups (push-pull).
101: Reserved
110: Test Mode. In this mode the FIFO may be written and read, but the data will not be transmitted
on the parallel port. All drivers have active pull-ups (push-pull).
111: Configuration Mode. In this mode the confgA, confgB registers are accessible at 0x400 and
0x401. All drivers have active pull-ups (push-pull).
Table 45B
Table 45C
CONFIG REG B
CONFIG REG B
DMA
BITS 2:0
IRQ SELECTED
BITS 5:3
SELECTED
15
14
11
10
9
7
5
110
101
100
011
010
001
111
000
3
2
1
011
010
001
000
All Others
All Others
SMSC DS – LPC47M14X
Page 90
Rev. 03/19/2001
OPERATION
Mode Switching/Software Control
Software will execute P1284 negotiation and all operation prior to a data transfer phase under programmed I/O control
(mode 000 or 001). Hardware provides an automatic control line handshake, moving data between the FIFO and the
ECP port only in the data transfer phase (modes 011 or 010).
Setting the mode to 011 or 010 will cause the hardware to initiate data transfer.
If the port is in mode 000 or 001 it may switch to any other mode. If the port is not in mode 000 or 001 it can only be
switched into mode 000 or 001. The direction can only be changed in mode 001.
Once in an extended forward mode the software should wait for the FIFO to be empty before switching back to mode
000 or 001. In this case all control signals will be deasserted before the mode switch. In an ecp reverse mode the
software waits for all the data to be read from the FIFO before changing back to mode 000 or 001. Since the automatic
hardware ecp reverse handshake only cares about the state of the FIFO it may have acquired extra data which will be
discarded. It may in fact be in the middle of a transfer when the mode is changed back to 000 or 001. In this case the
port will deassert nAutoFd independent of the state of the transfer. The design shall not cause glitches on the
handshake signals if the software meets the constraints above.
ECP Operation
Prior to ECP operation the Host must negotiate on the parallel port to determine if the peripheral supports the ECP
protocol. This is a somewhat complex negotiation carried out under program control in mode 000.
After negotiation, it is necessary to initialize some of the port bits. The following are required:
Set Direction = 0, enabling the drivers.
Set strobe = 0, causing the nStrobe signal to default to the deasserted state.
Set autoFd = 0, causing the nAutoFd signal to default to the deasserted state.
Set mode = 011 (ECP Mode)
ECP address/RLE bytes or data bytes may be sent automatically by writing the ecpAFifo or ecpDFifo respectively.
Note that all FIFO data transfers are byte wide and byte aligned. Address/RLE transfers are byte-wide and only allowed
in the forward direction.
The host may switch directions by first switching to mode = 001, negotiating for the forward or reverse channel, setting
direction to 1 or 0, then setting mode = 011. When direction is 1 the hardware shall handshake for each ECP read data
byte and attempt to fill the FIFO. Bytes may then be read from the ecpDFifo as long as it is not empty.
ECP transfers may also be accomplished (albeit slowly) by handshaking individual bytes under program control in mode
= 001, or 000.
Termination from ECP Mode
Termination from ECP Mode is similar to the termination from Nibble/Byte Modes. The host is permitted to terminate
from ECP Mode only in specific well-defined states. The termination can only be executed while the bus is in the forward
direction. To terminate while the channel is in the reverse direction, it must first be transitioned into the forward direction.
Command/Data
ECP Mode supports two advanced features to improve the effectiveness of the protocol for some applications. The
features are implemented by allowing the transfer of normal 8 bit data or 8 bit commands.
When in the forward direction, normal data is transferred when HostAck is high and an 8 bit command is transferred
when HostAck is low.
The most significant bit of the command indicates whether it is a run-length count (for compression) or a channel
address.
When in the reverse direction, normal data is transferred when PeriphAck is high and an 8 bit command is transferred
when PeriphAck is low. The most significant bit of the command is always zero. Reverse channel addresses are seldom
used and may not be supported in hardware.
SMSC DS – LPC47M14X
Page 91
Rev. 03/19/2001
Table 46 – Channel/Data Commands supported in ECP mode
Forward Channel Commands (HostAck Low)
Reverse Channel Commands (PeripAck Low)
D7
D[6:0]
0
Run-Length Count (0-127)
(mode 0011 0X00 only)
1
Channel Address (0-127)
Data Compression
The ECP port supports run length encoded (RLE) decompression in hardware and can transfer compressed data to a
peripheral. Run length encoded (RLE) compression in hardware is not supported. To transfer compressed data in ECP
mode, the compression count is written to the ecpAFifo and the data byte is written to the ecpDFifo.
Compression is accomplished by counting identical bytes and transmitting an RLE byte that indicates how many times
the next byte is to be repeated. Decompression simply intercepts the RLE byte and repeats the following byte the
specified number of times. When a run-length count is received from a peripheral, the subsequent data byte is replicated
the specified number of times. A run-length count of zero specifies that only one byte of data is represented by the next
data byte, whereas a run-length count of 127 indicates that the next byte should be expanded to 128 bytes. To prevent
data expansion, however, run-length counts of zero should be avoided.
Pin Definition
The drivers for nStrobe, nAutoFd, nInit and nSelectIn are open-collector in mode 000 and are push-pull in all other
modes.
LPC Connections
The interface can never stall causing the host to hang. The width of data transfers is strictly controlled on an I/O address
basis per this specification. All FIFO-DMA transfers are byte wide, byte aligned and end on a byte boundary. (The
PWord value can be obtained by reading Configuration Register A, cnfgA, described in the next section). Single byte
wide transfers are always possible with standard or PS/2 mode using program control of the control signals.
Interrupts
The interrupts are enabled by serviceIntr in the ecr register.
serviceIntr = 1
Disables the DMA and all of the service interrupts.
serviceIntr = 0 Enables the selected interrupt condition. If the interrupting condition is valid, then the interrupt is
generated immediately when this bit is changed from a 1 to a 0. This can occur during Programmed
I/O if the number of bytes removed or added from/to the FIFO does not cross the threshold.
An interrupt is generated when:
1) For DMA transfers: When serviceIntr is 0, dmaEn is 1 and the DMA TC cycle is received.
2) For Programmed I/O:
a) When serviceIntr is 0, dmaEn is 0, direction is 0 and there are writeIntrThreshold or more free bytes in the
FIFO. Also, an interrupt is generated when serviceIntr is cleared to 0 whenever there are writeIntrThreshold or
more free bytes in the FIFO.
b) When serviceIntr is 0, dmaEn is 0, direction is 1 and there are readIntrThreshold or more bytes in the FIFO.
Also, an interrupt is generated when serviceIntr is cleared to 0 whenever there are readIntrThreshold or more
bytes in the FIFO.
3) When nErrIntrEn is 0 and nFault transitions from high to low or when nErrIntrEn is set from 1 to 0 and nFault is
asserted.
4) When ackIntEn is 1 and the nAck signal transitions from a low to a high.
SMSC DS – LPC47M14X
Page 92
Rev. 03/19/2001
FIFO Operation
The FIFO threshold is set in the chip configuration registers. All data transfers to or from the parallel port can proceed in
DMA or Programmed I/O (non-DMA) mode as indicated by the selected mode. The FIFO is used by selecting the
Parallel Port FIFO mode or ECP Parallel Port Mode. (FIFO test mode will be addressed separately.) After a reset, the
FIFO is disabled. Each data byte is transferred by a Programmed I/O cycle or DMA cycle depending on the selection of
DMA or Programmed I/O mode.
The following paragraphs detail the operation of the FIFO flow control. In these descriptions, <threshold> ranges from 1
to 16. The parameter FIFOTHR, which the user programs, is one less and ranges from 0 to 15.
A low threshold value (i.e. 2) results in longer periods of time between service requests, but requires faster servicing of
the request for both read and write cases. The host must be very responsive to the service request. This is the desired
case for use with a "fast" system. A high value of threshold (i.e. 12) is used with a "sluggish" system by affording a long
latency period after a service request, but results in more frequent service requests.
DMA TRANSFERS
DMA transfers are always to or from the ecpDFifo, tFifo or CFifo. DMA utilizes the standard PC DMA services. To use
the DMA transfers, the host first sets up the direction and state as in the programmed I/O case. Then it programs the
DMA controller in the host with the desired count and memory address. Lastly it sets dmaEn to 1 and serviceIntr to 0.
The ECP requests DMA transfers from the host by encoding the LDRQ# pin. The DMA will empty or fill the FIFO using
the appropriate direction and mode. When the terminal count in the DMA controller is reached, an interrupt is generated
and serviceIntr is asserted, disabling DMA. In order to prevent possible blocking of refresh requests a DMA cycle shall
not be requested for more than 32 DMA cycles in a row. The FIFO is enabled directly by the host initiating a DMA cycle
for the requested channel, and addresses need not be valid. An interrupt is generated when a TC cycle is received.
(Note: The only way to properly terminate DMA transfers is with a TC cycle.)
DMA may be disabled in the middle of a transfer by first disabling the host DMA controller. Then setting serviceIntr to 1,
followed by setting dmaEn to 0, and waiting for the FIFO to become empty or full. Restarting the DMA is accomplished
by enabling DMA in the host, setting dmaEn to 1, followed by setting serviceIntr to 0.
DMA Mode - Transfers from the FIFO to the Host
(Note: In the reverse mode, the peripheral may not continue to fill the FIFO if it runs out of data to transfer, even if the
chip continues to request more data from the peripheral.)
The ECP requests a DMA cycle whenever there is data in the FIFO. The DMA controller must respond to the request by
reading data from the FIFO. The ECP stops requesting DMA cycles when the FIFO becomes empty or when a TC cycle
is received, indicating that no more data is required. If the ECP stops requesting DMA cycles due to the FIFO going
empty, then a DMA cycle is requested again as soon as there is one byte in the FIFO. If the ECP stops requesting DMA
cycles due to the TC cycle, then a DMA cycle is requested again when there is one byte in the FIFO, and serviceIntr has
been re-enabled.
Programmed I/O Mode or Non-DMA Mode
The ECP or parallel port FIFOs may also be operated using interrupt driven programmed I/O. Software can determine
the writeIntrThreshold, readIntrThreshold, and FIFO depth by accessing the FIFO in Test Mode.
Programmed I/O transfers are to the ecpDFifo at 400H and ecpAFifo at 000H or from the ecpDFifo located at 400H, or
to/from the tFifo at 400H. To use the programmed I/O transfers, the host first sets up the direction and state, sets
dmaEn to 0 and serviceIntr to 0.
The ECP requests programmed I/O transfers from the host by activating the interrupt. The programmed I/O will empty or
fill the FIFO using the appropriate direction and mode.
Note: A threshold of 16 is equivalent to a threshold of 15. These two cases are treated the same.
Programmed I/O - Transfers from the FIFO to the Host
In the reverse direction an interrupt occurs when serviceIntr is 0 and readIntrThreshold bytes are available in the FIFO.
If at this time the FIFO is full it can be emptied completely in a single burst, otherwise readIntrThreshold bytes may be
read from the FIFO in a single burst.
readIntrThreshold =(16-<threshold>) data bytes in FIFO
An interrupt is generated when serviceIntr is 0 and the number of bytes in the FIFO is greater than or equal to (16-
<threshold>). (If the threshold = 12, then the interrupt is set whenever there are 4-16 bytes in the FIFO). The host must
respond to the request by reading data from the FIFO. This process is repeated until the last byte is transferred out of
SMSC DS – LPC47M14X
Page 93
Rev. 03/19/2001
the FIFO. If at this time the FIFO is full, it can be completely emptied in a single burst, otherwise a minimum of (16-
<threshold>) bytes may be read from the FIFO in a single burst.
Programmed I/O - Transfers from the Host to the FIFO
In the forward direction an interrupt occurs when serviceIntr is 0 and there are writeIntrThreshold or more bytes free in
the FIFO. At this time if the FIFO is empty it can be filled with a single burst before the empty bit needs to be re-read.
Otherwise it may be filled with writeIntrThreshold bytes.
writeIntrThreshold
=
(16-<threshold>) free bytes in FIFO
An interrupt is generated when serviceIntr is 0 and the number of bytes in the FIFO is less than or equal to <threshold>.
(If the threshold = 12, then the interrupt is set whenever there are 12 or less bytes of data in the FIFO.) The host must
respond to the request by writing data to the FIFO. If at this time the FIFO is empty, it can be completely filled in a single
burst, otherwise a minimum of (16-<threshold>) bytes may be written to the FIFO in a single burst. This process is
repeated until the last byte is transferred into the FIFO.
6.10 POWER MANAGEMENT
Power management capabilities are provided for the following logical devices: floppy disk, UART 1, UART 2 and the
parallel port. For each logical device, two types of power management are provided: direct powerdown and auto
powerdown.
FDC Power Management
Direct power management is controlled by CR22. Refer to CR22 for more information.
Auto Power Management is enabled by CR23-B0. When set, this bit allows FDC to enter powerdown when all of the
following conditions have been met:
1) The motor enable pins of register 3F2H are inactive (zero).
2) The part must be idle; MSR=80H and INT = 0 (INT may be high even if MSR = 80H due to polling interrupts).
3) The head unload timer must have expired.
4) The Auto powerdown timer (10msec) must have timed out.
An internal timer is initiated as soon as the auto powerdown command is enabled. The part is then powered down when
all the conditions are met.
Disabling the auto powerdown mode cancels the timer and holds the FDC block out of auto powerdown.
Note: At least 8us delay should be added when exiting FDC Auto Powerdown mode. If the operating environment is
such that this delay cannot be guaranteed, the auto powerdown mode should not be used and Direct powerdown
mode should be used instead. The Direct powerdown mode requires at least 8us delay at 250K bits/sec
configuration and 4us delay at 500K bits/sec. The delay should be added so that the internal microcontroller can
prepare itself to accept commands.
DSR From Powerdown
If DSR powerdown is used when the part is in auto powerdown, the DSR powerdown will override the auto powerdown.
However, when the part is awakened from DSR powerdown, the auto powerdown will once again become effective.
Wake Up From Auto Powerdown
If the part enters the powerdown state through the auto powerdown mode, then the part can be awakened by reset or by
appropriate access to certain registers.
If a hardware or software reset is used then the part will go through the normal reset sequence. If the access is through
the selected registers, then the FDC resumes operation as though it was never in powerdown. Besides activating the
PCI_RESET# pin or one of the software reset bits in the DOR or DSR, the following register accesses will wake up the
part:
1) Enabling any one of the motor enable bits in the DOR register (reading the DOR does not awaken the part).
2) A read from the MSR register.
3) A read or write to the Data register.
Once awake, the FDC will reinitiate the auto powerdown timer for 10 ms. The part will powerdown again when all
the powerdown conditions are satisfied.
SMSC DS – LPC47M14X
Page 94
Rev. 03/19/2001
Register Behavior
Table 47 illustrates the AT and PS/2 (including Model 30) configuration registers available and the type of access
permitted. In order to maintain software transparency, access to all the registers must be maintained. As Table 47
shows, two sets of registers are distinguished based on whether their access results in the part remaining in powerdown
state or exiting it.
Access to all other registers is possible without awakening the part. These registers can be accessed during
powerdown without changing the status of the part. A read from these registers will reflect the true status as shown in
the register description in the FDC description. A write to the part will result in the part retaining the data and
subsequently reflecting it when the part awakens. Accessing the part during powerdown may cause an increase in the
power consumption by the part. The part will revert back to its low power mode when the access has been completed.
Pin Behavior
The LPC47M14x is specifically designed for systems in which power conservation is a primary concern. This makes the
behavior of the pins during powerdown very important.
The pins of the LPC47M14x can be divided into two major categories: system interface and floppy disk drive interface.
The floppy disk drive pins are disabled so that no power will be drawn through the part as a result of any voltage applied
to the pin within the part's power supply range. Most of the system interface pins are left active to monitor system
accesses that may wake up the part.
Table 47 – PC/AT and PS/2 Available Registers
AVAILABLE REGISTERS
BASE + ADDRESS
PC-AT
PS/2 (MODEL 30)
ACCESS PERMITTED
Access to these registers DOES NOT wake up the part
00H
01H
02H
03H
04H
06H
07H
07H
----
----
DOR (1)
---
DSR (1)
---
DIR
SRA
SRB
DOR (1)
---
DSR (1)
---
R
R
R/W
---
W
---
R
W
DIR
CCR
CCR
Access to these registers wakes up the part
04H
05H
MSR
Data
MSR
Data
R
R/W
Note 1: Writing to the DOR or DSR does not wake up the part, however, writing any of the motor enable bits or doing a
software reset (via DOR or DSR reset bits) will wake up the part.
SMSC DS – LPC47M14X
Page 95
Rev. 03/19/2001
System Interface Pins
Table 48 gives the state of the interface pins in the powerdown state. Pins unaffected by the powerdown are labeled
“Unchanged.”
Table 48 – State of System Pins in Auto Powerdown
SYSTEM PINS
LAD[3:0]
STATE IN AUTO POWERDOWN
Unchanged
LDRQ#
Unchanged
LPCPD#
Unchanged
LFRAME#
PCI_RESET#
PCI_CLK
Unchanged
Unchanged
Unchanged
SER_IRQ
Unchanged
FDD Interface Pins
All pins in the FDD interface, which can be connected directly to the floppy disk drive itself, are either DISABLED or
TRISTATED. Pins used for local logic control or part programming are unaffected.
Table 49 depicts the state of the floppy disk drive interface pins in the powerdown state.
Table 49 – State of Floppy Disk Drive Interface Pins in Powerdown
FDD PINS
STATE IN AUTO POWERDOWN
INPUT PINS
Input
nRDATA
nWRTPRT
nTRK0
Input
Input
nINDEX
Input
nDSKCHG
Input
OUTPUT PINS
Tristated
Tristated
Active
nMTR0
nDS0
nDIR
nSTEP
Active
nWDATA
nWGATE
nHDSEL
DRVDEN[0:1]
Tristated
Tristated
Active
Active
SMSC DS – LPC47M14X
Page 96
Rev. 03/19/2001
UART Power Management
Direct power management is controlled by CR22. Refer to CR22 for more information.
Auto Power Management is enabled by CR23-B4 and B5. When set, these bits allow the following auto power
management operations:
1) The transmitter enters auto powerdown when the transmit buffer and shift register are empty.
2) The receiver enters powerdown when the following conditions are all met:
a) Receive FIFO is empty
b) The receiver is waiting for a start bit.
Note: While in powerdown the Ring Indicator interrupt is still valid and transitions when the RI input changes.
Exit Auto Powerdown
The transmitter exits powerdown on a write to the XMIT buffer. The receiver exits auto powerdown when RXDx
changes state.
Parallel Port
Direct power management is controlled by CR22. Refer to CR22 for more information.
Auto Power Management is enabled by CR23-B3. When set, this bit allows the ECP or EPP logical parallel port blocks
to be placed into powerdown when not being used.
The EPP logic is in powerdown under any of the following conditions:
1) EPP is not enabled in the configuration registers.
2) EPP is not selected through ecr while in ECP mode.
The ECP logic is in powerdown under any of the following conditions:
1) ECP is not enabled in the configuration registers.
2) SPP, PS/2 Parallel port or EPP mode is selected through ecr while in ECP mode.
Exit Auto Powerdown
The parallel port logic can change powerdown modes when the ECP mode is changed through the ecr register or when
the parallel port mode is changed through the configuration registers.
SMSC DS – LPC47M14X
Page 97
Rev. 03/19/2001
6.11 SERIAL IRQ
The LPC47M14x supports the serial interrupt to transmit interrupt information to the host system. The serial interrupt
scheme adheres to the Serial IRQ Specification for PCI Systems, Version 6.0.
Timing Diagrams For SER_IRQ Cycle
A) Start Frame timing with source sampled a low pulse on IRQ1
START FRAME
IRQ0 FRAME IRQ1 FRAME IRQ2 FRAME
SL
or
H
R
T
S
R
T
S
R
T
S
R
T
H
PCI_CLK
1
START
SER_IRQ
Drive Source
IRQ1
Host Controller
None
IRQ1
None
Note: H=Host Control; R=Recovery; T=Turn-Around; SL=Slave Control; S=Sample
Note 1: Start Frame pulse can be 4-8 clocks wide depending on the location of the device in the PCI bridge
hierarchy in a synchronous bridge design.
B) Stop Frame Timing with Host using 17 SER_IRQ sampling period
IRQ14
IRQ15
IOCHCK#
FRAME
STOP FRAME
NEXT CYCLE
FRAME
FRAME
I 2
S
R
T
S
R
T
S
R
T
H
R
T
PCI_CLK
SER_IRQ
1
3
STOP
START
None
IRQ15
None
Host Controller
Driver
Note: H=Host Control; R=Recovery; T=Turn-Around; S=Sample; I=Idle
Note 1: The next SER_IRQ cycle’s Start Frame pulse may or may not start immediately after the turn-around clock
of the Stop Frame.
Note 2: There may be none, one or more Idle states during the Stop Frame.
Note 3: Stop pulse is 2 clocks wide for Quiet mode, 3 clocks wide for Continuous mode.
SMSC DS – LPC47M14X
Page 98
Rev. 03/19/2001
SER_IRQ Cycle Control
There are two modes of operation for the SER_IRQ Start Frame.
1)
Quiet (Active) Mode: Any device may initiate a Start Frame by driving the SER_IRQ low for one clock, while
the SER_IRQ is Idle. After driving low for one clock the SER_IRQ must immediately be tri-stated without at
any time driving high. A Start Frame may not be initiated while the SER_IRQ is Active. The SER_IRQ is Idle
between Stop and Start Frames. The SER_IRQ is Active between Start and Stop Frames. This mode of
operation allows the SER_IRQ to be Idle when there are no IRQ/Data transitions which should be most of the
time.
Once a Start Frame has been initiated the Host Controller will take over driving the SER_IRQ low in the next
clock and will continue driving the SER_IRQ low for a programmable period of three to seven clocks. This
makes a total low pulse width of four to eight clocks. Finally, the Host Controller will drive the SER_IRQ back
high for one clock, then tri-state. Any SER_IRQ Device (i.e., The LPC47M14x) which detects any transition
on an IRQ/Data line for which it is responsible must initiate a Start Frame in order to update the Host
Controller unless the SER_IRQ is already in an SER_IRQ Cycle and the IRQ/Data transition can be delivered
in that SER_IRQ Cycle.
2)
Continuous (Idle) Mode: Only the Host controller can initiate a Start Frame to update IRQ/Data line
information. All other SER_IRQ agents become passive and may not initiate a Start Frame. SER_IRQ will be
driven low for four to eight clocks by Host Controller. This mode has two functions. It can be used to stop or
idle the SER_IRQ or the Host Controller can operate SER_IRQ in a continuous mode by initiating a Start
Frame at the end of every Stop Frame.
An SER_IRQ mode transition can only occur during the Stop Frame. Upon reset, SER_IRQ bus is defaulted to
Continuous mode, therefore only the Host controller can initiate the first Start Frame. Slaves must
continuously sample the Stop Frames pulse width to determine the next SER_IRQ Cycle’s mode.
SER_IRQ Data Frame
Once a Start Frame has been initiated, the LPC47M14x will watch for the rising edge of the Start Pulse and start
counting IRQ/Data Frames from there. Each IRQ/Data Frame is three clocks: Sample phase, Recovery phase, and
Turn-around phase. During the Sample phase the LPC47M14x must drive the SER_IRQ low, if and only if, its last
detected IRQ/Data value was low. If its detected IRQ/Data value is high, SER_IRQ must be left tri-stated. During the
Recovery phase the LPC47M14x must drive the SER_IRQ high, if and only if, it had driven the SER_IRQ low during
the previous Sample Phase. During the Turn-around Phase the LPC47M14x must tri-state the SER_IRQ. The
LPC47M14x will drive the SER_IRQ line low at the appropriate sample point if its associated IRQ/Data line is low,
regardless of which device initiated the Start Frame.
The Sample Phase for each IRQ/Data follows the low to high transition of the Start Frame pulse by a number of
clocks equal to the IRQ/Data Frame times three, minus one. (e.g. The IRQ5 Sample clock is the sixth IRQ/Data
Frame, (6 x 3) - 1 = 17th clock after the rising edge of the Start Pulse).
SER_IRQ Sampling Periods
SER_IRQ PERIOD
SIGNAL SAMPLED
Not Used
IRQ1
# OF CLOCKS PAST START
1
2
2
5
3
4
5
6
7
8
9
10
11
12
13
14
15
16
nIO_SMI/IRQ2
IRQ3
8
11
14
17
20
23
26
29
32
35
38
41
44
47
IRQ4
IRQ5
IRQ6
IRQ7
IRQ8
IRQ9
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
SMSC DS – LPC47M14X
Page 99
Rev. 03/19/2001
The SER_IRQ data frame will now support IRQ2 from a logical device, previously SER_IRQ Period 3 was reserved
for use by the System Management Interrupt (nSMI). When using Period 3 for IRQ2 the user should mask off the
SMI via the SMI Enable Register. Likewise, when using Period 3 for nSMI the user should not configure any logical
devices as using IRQ2.
SER_IRQ Period 14 is used to transfer IRQ13. Logical devices 0 (FDC), 3 (Par Port), 4 (Ser Port 1), 5 (Ser Port 2),
and 7 (KBD) shall have IRQ13 as a choice for their primary interrupt.
The SMI is enabled onto the SMI frame of the Serial IRQ via bit 6 of SMI Enable Register 2 and onto the SMI pin via
bit 7 of the SMI Enable Register 2.
Stop Cycle Control
Once all IRQ/Data Frames have completed the Host Controller will terminate SER_IRQ activity by initiating a Stop
Frame. Only the Host Controller can initiate the Stop Frame. A Stop Frame is indicated when the SER_IRQ is low
for two or three clocks. If the Stop Frame’s low time is two clocks then the next SER_IRQ Cycle’s sampled mode is
the Quiet mode; and any SER_IRQ device may initiate a Start Frame in the second clock or more after the rising
edge of the Stop Frame’s pulse. If the Stop Frame’s low time is three clocks then the next SER_IRQ Cycle’s sampled
mode is the Continuos mode; and only the Host Controller may initiate a Start Frame in the second clock or more
after the rising edge of the Stop Frame’s pulse.
Latency
Latency for IRQ/Data updates over the SER_IRQ bus in bridge-less systems with the minimum Host supported
IRQ/Data Frames of seventeen, will range up to 96 clocks (3.84µS with a 25MHz PCI Bus or 2.88uS with a 33MHz
PCI Bus). If one or more PCI to PCI Bridge is added to a system, the latency for IRQ/Data updates from the
secondary or tertiary buses will be a few clocks longer for synchronous buses, and approximately double for
asynchronous buses.
EOI/ISR Read Latency
Any serialized IRQ scheme has a potential implementation issue related to IRQ latency. IRQ latency could cause an
EOI or ISR Read to precede an IRQ transition that it should have followed. This could cause a system fault. The host
interrupt controller is responsible for ensuring that these latency issues are mitigated. The recommended solution is
to delay EOIs and ISR Reads to the interrupt controller by the same amount as the SER_IRQ Cycle latency in order
to ensure that these events do not occur out of order.
AC/DC Specification Issue
All SER_IRQ agents must drive / sample SER_IRQ synchronously related to the rising edge of PCI bus clock. The
SER_IRQ pin uses the electrical specification of PCI bus. Electrical parameters will follow PCI spec. section 4,
sustained tri-state.
Reset and Initialization
The SER_IRQ bus uses nPCI_RESET as its reset signal. The SER_IRQ pin is tri-stated by all agents while
nPCI_RESET is active. With reset, SER_IRQ Slaves are put into the (continuous) IDLE mode. The Host Controller is
responsible for starting the initial SER_IRQ Cycle to collect system’s IRQ/Data default values. The system then
follows with the Continuous/Quiet mode protocol (Stop Frame pulse width) for subsequent SER_IRQ Cycles. It is
Host Controller’s responsibility to provide the default values to 8259’s and other system logic before the first
SER_IRQ Cycle is performed. For SER_IRQ system suspend, insertion, or removal application, the Host controller
should be programmed into Continuous (IDLE) mode first. This is to guarantee SER_IRQ bus is in IDLE state before
the system configuration changes.
SMSC DS – LPC47M14X
Page 100
Rev. 03/19/2001
6.12 INTERRUPT GENERATING REGISTERS
The LPC47M14x contains on-chip Interrupt Generating Registers to enable external software to generate IRQ1
through IRQ15 on the Serial IRQ Interface. These registers, INT_GEN1 and INT_GEN2 as shown below, are located
in the Logical Device A Runtime Block, at offsets 54h and 55h, respectively, from the Runtime Block base address
setting (set at Index 0x60 and 0x61, Logical Device A Configuration Registers).
Registers INT_GEN1 and INT_GEN2 are enabled to output to the Serial IRQ stream by setting Logical Device A
Configuration Register, at Index 0xF1, Bit [0] to ‘1’. When Bit [0] is set to ‘0’, INT_GEN1 and INT_GEN2 are
prevented from outputting to the Serial IRQ stream.
Writing Bits 0 through 8 to ‘0’ in registers INT_GEN1 and INT_GEN2 enable the corresponding interrupt (INT1
through INT15) to be asserted (made active) in the Serial IRQ stream. Producing an interrupt in the Serial IRQ stream
by writing these bits to ‘0’ overrides other interrupt sources for the Serial IRQ stream. No other functional logic in the
LPC47M14x sets bits in these registers. The asserted interrupt in the Serial IRQ stream from registers INT_GEN1
and INT_GEN2 is removed by writing the corresponding bit to ‘1’.
INT_GEN1 Register
NAME
LOCATION
DEFAULT VALUE
ATTRIBUTE
SIZE
INT_GEN1
Runtime Block Offset 54h
0xFF
Read/Write
8 bits
Bit 7
nINT 7
Bit 6
nINT 6
Bit 5
nINT 5
Bit 4
nINT 4
Bit 3
nINT 3
Bit 2
nINT2
Bit 1
nINT1
Bit 0
Reserved
INT_GEN2 Register
INT_GEN2
NAME
LOCATION
DEFAULT VALUE
ATTRIBUTE
SIZE
Runtime Block Offset 55h
0xFF
Read/Write
8 bits
Bit 7
nINT 15
Bit 6
nINT 14
Bit 5
nINT 13
Bit 4
nINT 12
Bit 3
nINT 11
Bit 2
nINT 10
Bit 1
nINT 9
Bit 0
nINT 8
SMSC DS – LPC47M14X
Page 101
Rev. 03/19/2001
6.13 8042 KEYBOARD CONTROLLER DESCRIPTION
The LPC47M14x is a Super I/O and Universal Keyboard Controller that is designed for intelligent keyboard management
in desktop computer applications. The Universal Keyboard Controller uses an 8042 microcontroller CPU core. This
section concentrates on the LPC47M14x enhancements to the 8042. For general information about the 8042, refer to
the "Hardware Description of the 8042" in the 8-Bit Embedded Controller Handbook.
8042A
LS05
P27
KDAT
KCLK
MCLK
MDAT
P10
P26
TST0
P23
TST1
P22
P11
Keyboard and Mouse Interface
KIRQ is the Keyboard IRQ
MIRQ is the Mouse IRQ
Port 21 is used to create a GATEA20 signal from the LPC47M14x.
SMSC DS – LPC47M14X
Page 102
Rev. 03/19/2001
6.13.1 Keyboard Interface
The LPC47M14x LPC interface is functionally compatible with the 8042 style host interface. It consists of the D0-7 data
signals; the read and write signals and the Status register, Input Data register, and Output Data register. Table 50
shows how the interface decodes the control signals. In addition to the above signals, the host interface includes
keyboard and mouse IRQs.
Table 50 – I/O Address Map
ADDRESS
COMMAND
Write
BLOCK
KDATA
KDATA
KDCTL
KDCTL
FUNCTION (NOTE 1)
Keyboard Data Write (C/D=0)
Keyboard Data Read
Keyboard Command Write (C/D=1)
Keyboard Status Read
0x60
Read
Write
Read
0x64
Note 1: These registers consist of three separate 8 bit registers. Status, Data/Command Write and Data Read.
Keyboard Data Write
This is an 8 bit write only register. When written, the C/D status bit of the status register is cleared to zero and the IBF
bit is set.
Keyboard Data Read
This is an 8 bit read only register. If enabled by "ENABLE FLAGS", when read, the KIRQ output is cleared and the OBF
flag in the status register is cleared. If not enabled, the KIRQ and/or AUXOBF1 must be cleared in software.
Keyboard Command Write
This is an 8 bit write only register. When written, the C/D status bit of the status register is set to one and the IBF bit is
set.
Keyboard Status Read
This is an 8 bit read only register. Refer to the description of the Status Register for more information.
CPU-to-Host Communication
The LPC47M14x CPU can write to the Output Data register via register DBB. A write to this register automatically sets
Bit 0 (OBF) in the Status register. See Table 51.
Table 51 – Host Interface Flags
8042 INSTRUCTION
OUT DBB
FLAG
Set OBF, and, if enabled, the KIRQ output signal goes high
Host-to-CPU Communication
The host system can send both commands and data to the Input Data register. The CPU differentiates between
commands and data by reading the value of Bit 3 of the Status register. When bit 3 is "1", the CPU interprets the register
contents as a command. When bit 3 is "0", the CPU interprets the register contents as data. During a host write
operation, bit 3 is set to "1" if SA2 = 1 or reset to "0" if SA2 = 0.
KIRQ
If "EN FLAGS" has been executed and P24 is set to a one: the OBF flag is gated onto KIRQ. The KIRQ signal can be
connected to system interrupt to signify that the LPC47M14x CPU has written to the output data register via "OUT
DBB,A". If P24 is set to a zero, KIRQ is forced low. On power-up, after a valid RST pulse has been delivered to the
device, KIRQ is reset to 0. KIRQ will normally reflects the status of writes "DBB". (KIRQ is normally selected as IRQ1 for
keyboard support.)
If "EN FLAGS” has not been executed: KIRQ can be controlled by writing to P24. Writing a zero to P24 forces KIRQ
low; a high forces KIRQ high.
MIRQ
If "EN FLAGS" has been executed and P25 is set to a one:; IBF is inverted and gated onto MIRQ. The MIRQ signal can
be connected to system interrupt to signify that the LPC47M14x CPU has read the DBB register. If "EN FLAGS” has not
been executed, MIRQ is controlled by P25, Writing a zero to P25 forces MIRQ low, a high forces MIRQ high. (MIRQ is
normally selected as IRQ12 for mouse support).
SMSC DS – LPC47M14X
Page 103
Rev. 03/19/2001
Gate A20
A general purpose P21 is used as a software controlled Gate A20 or user defined output.
8042 PINS
The 8042 functions P17, P16 and P12 are implemented as in a true 8042 part. Reference the 8042 spec for all timing.
A port signal of 0 drives the output to 0. A port signal of 1 causes the port enable signal to drive the output to 1 within 20-
30nsec. After 500nsec (six 8042 clocks) the port enable goes away and the external pull-up maintains the output signal
as 1.
In 8042 mode, the pins can be programmed as open drain. When programmed in open drain mode, the port enables
do not come into play. If the port signal is 0 the output will be 0. If the port signal is 1, the output tristates: an external
pull-up can pull the pin high, and the pin can be shared. In 8042 mode, the pins cannot be programmed as input nor
inverted through the GP configuration registers.
6.13.2 External Keyboard and Mouse Interface
Industry-standard PC-AT-compatible keyboards employ a two-wire, bi-directional TTL interface for data transmission.
Several sources also supply PS/2 mouse products that employ the same type of interface. To facilitate system
expansion, the LPC47M14x provides four signal pins that may be used to implement this interface directly for an
external keyboard and mouse.
The LPC47M14x has four high-drive, open-drain output, bi-directional port pins that can be used for external serial
interfaces, such as external keyboard and PS/2-type mouse interfaces. They are KCLK, KDAT, MCLK, and MDAT. P26
is inverted and output as KCLK. The KCLK pin is connected to TEST0. P27 is inverted and output as KDAT. The
KDAT pin is connected to P10. P23 is inverted and output as MCLK. The MCLK pin is connected to TEST1. P22 is
inverted and output as MDAT. The MDAT pin is connected to P11.
Note: External pull-ups may be required.
6.13.3 Keyboard Power Management
The keyboard provides support for two power-saving modes: soft powerdown mode and hard powerdown mode. In soft
powerdown mode, the clock to the ALU is stopped but the timer/counter and interrupts are still active. In hard power
down mode the clock to the 8042 is stopped.
Soft Power Down Mode
This mode is entered by executing a HALT instruction. The execution of program code is halted until either RESET is
driven active or a data byte is written to the DBBIN register by a master CPU. If this mode is exited using the interrupt,
and the IBF interrupt is enabled, then program execution resumes with a CALL to the interrupt routine, otherwise the
next instruction is executed. If it is exited using RESET then a normal reset sequence is initiated and program execution
starts from program memory location 0.
Hard Power Down Mode
This mode is entered by executing a STOP instruction. The oscillator is stopped by disabling the oscillator driver
cell. When either RESET is driven active or a data byte is written to the DBBIN register by a master CPU, this mode will
be exited (as above). However, as the oscillator cell will require an initialization time, either RESET must be held active
for sufficient time to allow the oscillator to stabilize. Program execution will resume as above.
6.13.4 Interrupts
The LPC47M14x provides the two 8042 interrupts: IBF and the Timer/Counter Overflow.
6.13.5 Memory Configurations
The LPC47M14x provides 2K of on-chip ROM and 256 bytes of on-chip RAM.
SMSC DS – LPC47M14X
Page 104
Rev. 03/19/2001
6.13.6 Register Definitions
Host I/F Data Register
The Input Data register and Output Data register are each 8 bits wide. A write to this 8 bit register will load the Keyboard
Data Read Buffer, set the OBF flag and set the KIRQ output if enabled. A read of this register will read the data from the
Keyboard Data or Command Write Buffer and clear the IBF flag. Refer to the KIRQ and Status register descriptions for
more information.
Host I/F Status Register
The Status register is 8 bits wide.
Table 52 shows the contents of the Status register.
Table 52 – Status Register
D7
D6
D5
D4
D3
D2
D1
D0
UD
UD
UD
UD
C/D
UD
IBF
OBF
Status Register
This register is cleared on a reset. This register is read-only for the Host and read/write by the LPC47M14x CPU.
UD
Writable by LPC47M14x CPU. These bits are user-definable.
C/D
(Command Data)-This bit specifies whether the input data register contains data or a command (0 = data, 1 =
command). During a host data/command write operation, this bit is set to "1" if SA2 = 1 or reset to "0" if SA2 =
0.
IBF
(Input Buffer Full)- This flag is set to 1 whenever the host system writes data into the input data register.
Setting this flag activates the LPC47M14x CPU's nIBF (MIRQ) interrupt if enabled. When the LPC47M14x CPU
reads the input data register (DBB), this bit is automatically reset and the interrupt is cleared. There is no
output pin associated with this internal signal.
OBF
(Output Buffer Full) - This flag is set to whenever the LPC47M14x CPU write to the output data register (DBB).
When the host system reads the output data register, this bit is automatically reset.
6.13.7 External Clock Signal
The LPC47M14x Keyboard Controller clock source is a 12 MHz clock generated from a 14.318 MHz clock. The reset
pulse must last for at least 24 16 MHz clock periods. The pulse-width requirement applies to both internally (Vcc POR)
and externally generated reset signals. In powerdown mode, the external clock signal is not loaded by the chip.
6.13.8 Default Reset Conditions
The LPC47M14x has one source of hardware reset: an external reset via the PCI_RESET# pin. Refer to Table 53 for
the effect of each type of reset on the internal registers.
Table 53 – Resets
HARDWARE RESET
(PCI_RESET#)
DESCRIPTION
KCLK
Low
Low
Low
Low
N/A
00H
KDAT
MCLK
MDAT
Host I/F Data Reg
Host I/F Status Reg
N/A: Not Applicable
GATEA20 AND KEYBOARD RESET
The LPC47M14x provides two options for GateA20 and Keyboard Reset: 8042 Software Generated GateA20 and
KRESET and Port 92 Fast GateA20 and KRESET.
SMSC DS – LPC47M14X
Page 105
Rev. 03/19/2001
PORT 92 FAST GATEA20 AND KEYBOARD RESET
Port 92 Register
This port can only be read or written if Port 92 has been enabled via bit 2 of the KRST_GA20 Register (Logical
Device 7, 0xF0) set to 1.
This register is used to support the alternate reset (nALT_RST) and alternate A20 (ALT_A20) functions.
NAME
LOCATION
DEFAULT VALUE
ATTRIBUTE
SIZE
Port 92
92h
24h
Read/Write
8 bits
Port 92 Register
Bit
7:6
5
Function
Reserved. Returns 00 when read
Reserved. Returns a 1 when read
Reserved. Returns a 0 when read
Reserved. Returns a 0 when read
Reserved. Returns a 1 when read
ALT_A20 Signal control. Writing a 0 to this bit causes the ALT_A20 signal to be
driven low. Writing a 1 to this bit causes the ALT_A20 signal to be driven high.
Alternate System Reset. This read/write bit provides an alternate system reset
function. This function provides an alternate means to reset the system CPU to
effect a mode switch from Protected Virtual Address Mode to the Real Address
Mode. This provides a faster means of reset than is provided by the Keyboard
controller. This bit is set to a 0 by a system reset. Writing a 1 to this bit will cause
the nALT_RST signal to pulse active (low) for a minimum of 1 µs after a delay of
500 ns. Before another nALT_RST pulse can be generated, this bit must be written
back to a 0.
4
3
2
1
0
nGATEA20
8042
P21
0
0
1
SYSTEM
ALT_A20
nA20M
0
1
0
1
0
1
1
1
1
Bit 0 of Port 92, which generates the nALT_RST signal, is used to reset the CPU under program control. This signal
is AND’ed together externally with the reset signal (nKBDRST) from the keyboard controller to provide a software
means of resetting the CPU. This provides a faster means of reset than is provided by the keyboard controller.
Writing a 1 to bit 0 in the Port 92 Register causes this signal to pulse low for a minimum of 6µs, after a delay of a
minimum of 14µs. Before another nALT_RST pulse can be generated, bit 0 must be set to 0 either by a system reset
of a write to Port 92. Upon reset, this signal is driven inactive high (bit 0 in the Port 92 Register is set to 0).
If Port 92 is enabled, i.e., bit 2 of KRST_GA20 is set to 1, then a pulse is generated by writing a 1 to bit 0 of the Port
92 Register and this pulse is AND’ed with the pulse generated from the 8042. This pulse is output on pin KRESET
and its polarity is controlled by the GPI/O polarity configuration.
SMSC DS – LPC47M14X
Page 106
Rev. 03/19/2001
14us
~~
6us
8042
P20
KRST
KBDRS
KRST_GA2
Bit 2
P92
nALT_RST
6us
Bit 0
Pulse
Gen
14us
Note: When Port 92 is
writes are ignored and
return undefined
~
~
Bit 1 of Port 92, the ALT_A20 signal, is used to force nA20M to the CPU low for support of real mode compatible
software. This signal is externally OR’ed with the A20GATE signal from the keyboard controller and CPURST to
control the nA20M input of the CPU. Writing a 0 to bit 1 of the Port 92 Register forces ALT_A20 low. ALT_A20 low
drives nA20M to the CPU low, if A20GATE from the keyboard controller is also low. Writing a 1 to bit 1 of the Port 92
Register forces ALT_A20 high. ALT_A20 high drives nA20M to the CPU high, regardless of the state of A20GATE
from the keyboard controller. Upon reset, this signal is driven low.
SMSC DS – LPC47M14X
Page 107
Rev. 03/19/2001
6.13.9 Latches On Keyboard and Mouse IRQs
The implementation of the latches on the keyboard and mouse interrupts is shown below.
KLATCH Bit
VCC
D
KINT
new
Q
KINT
CLR
8042
RD 60
FIGURE 6 – KEYBOARD LATCH
MLATCH Bit
VCC
MINT
new
D
Q
MINT
CLR
8042
RD 60
FIGURE 7 – MOUSE LATCH
The KLATCH and MLATCH bits are located in the KRST_GA20 register, in Logical Device 7 at 0xF0.
These bits are defined as follows:
Bit[4]: MLATCH – Mouse Interrupt latch control bit. 0=MINT is the 8042 MINT ANDed with Latched MINT
(default), 1=MINT is the latched 8042 MINT.
Bit[3]: KLATCH – Keyboard Interrupt latch control bit. 0=KINT is the 8042 KINT ANDed with Latched
KINT (default), 1=KINT is the latched 8042 KINT.
See the “Configuration” section for a description of this register.
SMSC DS – LPC47M14X
Page 108
Rev. 03/19/2001
6.13.10 Keyboard and Mouse PME Generation
The LPC47M14x sets the associated PME Status bits when the following conditions occur:
ꢀ
ꢀ
•
•
Keyboard Interrupt
Mouse Interrupt
Active Edge on Keyboard Data Signal (KDAT)
Active Edge on Mouse Data Signal (MDAT)
These events can cause a PME to be generated if the associated PME Wake Enable register bit and the global
PME_EN bit are set. Refer to the PME Support section for more details on the PME interface logic and refer to the
“Runtime Registers” section for details on the PME Status and Enable registers.
The keyboard interrupt and mouse interrupt PMEs can be generated when the part is powered by VCC. The
keyboard data and mouse data PMEs can be generated both when the part is powered by VCC, and when the part is
powered by VTR (VCC=0).
When using the keyboard and mouse data signals for wakeup, it may be necessary to isolate the keyboard signals
(KCLK, KDAT, MCLK, MDAT) from the 8042 prior to entering certain system sleep states. This is due to the fact that
the normal operation of the 8042 can prevent the system from entering a sleep state or trigger false PME events.
The LPC47M14x has “isolation” bits for the keyboard and mouse signals, which allow the keyboard and mouse data
signals to go into the wakeup logic but block the clock and data signals from the 8042. These bits may be used
anytime it is necessary to isolate the 8042 keyboard and mouse signals from the 8042 before entering a system sleep
state.
See the SMSC Application Note titled “Keyboard and Mouse Wakeup Functionality” for more information.
The bits used to isolate the keyboard and mouse signals from the 8042 are located in Logical Device 7, Register
0xF0 (KRST_GA20) and are defined as follows:
Bit[6]
Bit[5]
M_ISO. Enables/disables isolation of mouse signals into 8042. Does not affect the MDAT signal to
the mouse wakeup (PME) logic.
1=block mouse clock and data signals into 8042
0= do not block mouse clock and data signals into 8042
K_ISO. Enables/disables isolation of keyboard signals into 8042. Does not affect the KDAT signal
to the keyboard wakeup (PME) logic.
1=block keyboard clock and data signals into 8042
0= do not block keyboard clock and data signals into 8042
When the keyboard and/or mouse isolation bits are used, it may be necessary to reset the 8042 upon exiting the
sleep state. If either of the isolation bits is set prior to entering a sleep state where VCC goes inactive (S3-S5), then
the 8042 must be reset upon exiting the sleep mode. Write 0x40 to global configuration register 0x2C to reset the
8042. The 8042 must then be taken out of reset by writing 0x00 to register 0x2C since the bit that resets the 8042 is
not self-clearing. Caution: Bit 6 of configuration register 0x2C is used to put the 8042 into reset - do not set any of the
other bits in register 0x2C, as this may produce undesired results.
It is not necessary to reset the 8042 if the isolation bits are used for a sleep state where VCC does not go inactive
(S1, S2).
SMSC DS – LPC47M14X
Page 109
Rev. 03/19/2001
6.14 GENERAL PURPOSE I/O
The LPC47M14x provides a set of flexible Input/Output control functions to the system designer through the 37
dedicated independently programmable General Purpose I/O pins (GPIO). The GPIO pins can perform basic I/O and
many of them can be individually enabled to generate an SMI and a PME.
6.14.1 GPIO Pins
The following pins include GPIO functionality. These pins are defined in the table below. All GPIOs default to the
GPIO function except for GP34 and GP35 which default to IRRX2 and IRTX2.
PIN
1
2
NAME
GP40 /DRVDEN0
GP41 /DRVDEN1 /EETI
GP42 /nIO_PME
GP43/DDRC/EETI
GP10 /J1B1
GP11 /J1B2
GP12 /J2B1
GP13 /J2B2
GP14 /J1X
GP15 /J1Y
GP16 /J2X
GP17 /J2Y
GP20 /P17
GP21 /P16 /EETI
GP22 /P12 /EETI
GP24 (SYSOPT)
GP25 /MIDI_IN
GP26 /MIDI_OUT
GP60 /LED1 /EETI
GP61 /LED2 /EETI
GP27/nIO_SMI
GP30 /FAN_TACH2
GP31 /FAN_TACH1
GP32 /FAN2
GP33 /FAN1
IRRX2/GP34
IRTX2/GP35
GP36 /nKBDRST
GP37 /A20M
GP50 /nRI2
GP51 /nDCD2
GP52 /RXD2
17
28
32
33
34
35
36
37
38
39
41
42
43
45
46
47
48
49
50
51
52
54
55
61
62
63
64
92
94
95
96
97
98
99
100
GP53 /TXD2
GP54 /nDSR2
GP55 /nRTS2
GP56 /nCTS2
GP57 /nDTR2
SMSC DS – LPC47M14X
Page 110
Rev. 03/19/2001
6.14.2 Description
Each GPIO port has a 1-bit data register and an 8-bit configuration control register. The data register for each GPIO
port is represented as a bit in one of the 8-bit GPIO DATA Registers, GP1 to GP6. The bits in these registers reflect
the value of the associated GPIO pin as follows. Pin is an input: The bit is the value of the GPIO pin. Pin is an
output: The value written to the bit goes to the GPIO pin. Latched on read and write. All of the GPIO registers are
located in the PME block see “Run Time Register” section. The GPIO ports with their alternate functions and
configuration state register addresses are listed in Table 54.
Table 54 – General Purpose I/O Port Assignments
ALT.
ALT.
FUNCTION
2
DATA
REGISTER
BIT NO.
REGISTER
OFFSET
(HEX)
PIN #
QFP
DEFAULT
DATA
FUNCTION
ALT. FUNC. 1
FUNCTION
REGISTER1
3
32
33
34
35
36
37
38
39
41
42
43
N/A
45
46
47
50
51
52
54
55
61
62
63
64
1
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
Reserved
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
Infrared Rx
Infrared Tx
GPIO
GPIO
GPIO
GPIO
GPIO
Joystick 1 Button 1
Joystick 1 Button 2
Joystick 2 Button 1
Joystick 2 Button 2
Joystick 1 X-Axis
Joystick 1 Y-Axis
Joystick 2 X-Axis
Joystick 2 Y-Axis
P17
GP1
GP2
GP3
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
4B
4C
4D
P16
P12
EETI
EETI
System Option
MIDI_IN
MIDI_OUT
SMI Output
Fan Tachometer 2
Fan Tachometer 1
Fan Speed Control 2
Fan Speed Control 1
GPIO
GPIO
Keyboard Reset
Gate A20
Drive Density Select 0
Drive Density Select 1
GP4
GP5
4E
4F
2
17
EETI
Power Management
Event
28
GPIO
Device Disable Reg.
Control
EETI
3
N/A
92
94
95
96
97
98
99
100
48
Reserved
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
7:4
0
1
2
3
4
5
6
7
Ring Indicator 2
Data Carrier Detect 2
Receive Serial Data 2
Transmit Serial Data 2
Data Set Ready 2
Request to Send 2
Clear to Send 2
Date Terminal Ready
LED
97
98
99
100
50
GPIO
GPIO
EETI
EETI
GP6
0
1
49
LED
N/A
Reserved
7:2
Note 1:
The GPIO Data and Configuration Registers are located in PME block at the offset shown
from the PME_BLK address.
SMSC DS – LPC47M14X
Page 111
Rev. 03/19/2001
6.14.3 GPIO Control
Each GPIO port has an 8-bit control register that controls the behavior of the pin. These registers are defined in the
“Runtime Registers” section of this specification.
Each GPIO port may be configured as either an input or an output. If the pin is configured as an output, it can be
programmed as open-drain or push-pull. Inputs and outputs can be configured as non-inverting or inverting. Bit[0] of
each GPIO Configuration Register determines the port direction, bit[1] determines the signal polarity, and bit[7]
determines the output driver type select. The GPIO configuration register Output Type select bit[7] applies to GPIO
functions and the nSMI Alternate functions.
The Polarity Bit (bit 1) of the GPIO control registers control the GPIO pin when the pin is configured for the GPIO
function and when the pin is configured for the alternate function for all pins, with the exception of the DDRC function
on GP43, the analog game port pins (J1X, J1Y, J2X, J2Y) and the either edge triggered interrupts. When the
alternate function is selected for the analog joystick pins (GP14, GP15, GP16 and GP17), these pins become open
drain, non-inverted outputs.
The basic GPIO configuration options are summarized in Table 55.
Table 55 – GPIO Configuration Summary
SELECTED
FUNCTION
DIRECTION
BIT
POLARITY
BIT
DESCRIPTION
B0
0
0
1
1
B1
0
1
0
1
Pin is a non-inverted output.
Pin is an inverted output.
Pin is a non-inverted input.
Pin is an inverted input.
GPIO
6.14.4 GPIO Operation
GPIO
GPIO
Configuration
Register bit-1
(Polarity)
Configuration
Register bit-0
(Input/Output)
D-TYPE
SD-bit
D
Q
GPx_nIOW
GPx_nIOR
GPIO
PIN
0
1
Transparent
Q
D
GPIO
Data Register
Bit-n
FIGURE 8 – GPIO FUNCTION ILLUSTRATION
SMSC DS – LPC47M14X
Page 112
Rev. 03/19/2001
The operation of the GPIO ports is illustrated in FIGURE 8.
Note: FIGURE 8 is for illustration purposes only and is not intended to suggest specific implementation details.
Note: When the following functions are selected, the associated GPIO pins have bi-directional
functionality:
P12, P16, P17 and game port x-axis and y-axis inputs (J1X, J1Y, J2X, J2Y).
When a GPIO port is programmed as an input, reading it through the GPIO data register latches either the inverted or
non-inverted logic value present at the GPIO pin. Writing to a GPIO port that is programmed as an input has no
effect (Table 56)
When a GPIO port is programmed as an output, the logic value or the inverted logic value that has been written into
the GPIO data register is output to the GPIO pin. Reading from a GPIO port that is programmed as an output returns
the last value written to the data register (Table 56). When the GPIO is programmed as an output, the pin is
excluded from the PME and SMI logic.
Table 56 – GPIO Read/Write Behavior
HOST OPERATION
READ
GPIO INPUT PORT
LATCHED VALUE OF GPIO PIN
NO EFFECT
GPIO OUTPUT PORT
LAST WRITE TO GPIO DATA REGISTER
BIT PLACED IN GPIO DATA REGISTER
WRITE
The LPC47M14x provides 31 GPIOs that can directly generate a PME. See the table in the next section. The
polarity bit in the GPIO control registers select the edge on these GPIO pins that will set the associated status bit in
the PME_STS 2 register. The default is the low-to-high edge. If the corresponding enable bit in the PME_EN 2
register and the PME_EN bit in the PME_EN register is set, a PME will be generated. These registers are located in
the PME_BLK of runtime registers which are located at the address contained in the configuration registers 0x60 and
0x61 in Logical Device A. The PME status bits for the GPIOs are cleared on a write of ‘1’. In addition, the
LPC47M14x provides 19 GPIOs that can directly generate an SMI. See the table in the next section.
6.14.5 GPIO PME and SMI Functionality
The following GPIOs are dedicated wakeup GPIOs with a status and enable bit in the PME status and enable
registers:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
GP10-GP17
GP20-GP22, GP24-GP27
GP30-GP33
GP41, GP43
GP50-GP57
GP60, GP61
The following PME status and enable registers for these GPIOs:
ꢀ
ꢀ
ꢀ
ꢀ
PME_STS2 and PME_EN2 for GP10-GP17
PME_STS3 and PME_EN3 for GP20-GP22, GP24-GP27
PME_STS4 and PME_EN4 for GP30-GP33, GP41, GP43, GP60 and GP61
PME_STS5 and PME_EN5 for GP50-GP57
The following GPIOs can directly generate an SMI and have a status and enable bit in the SMI status and enable
registers.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
GP20-GP22, GP24-GP26
GP30-GP33
GP41, GP42, GP43
GP54-GP57
GP60, GP61
The following SMI status and enable registers for these GPIOs:
ꢀ
ꢀ
ꢀ
SMI_STS3 and SMI_EN3 for GP20-GP22, GP24-GP26 and GP60
SMI_STS4 and SMI_EN4 for GP30-GP33, GP41, GP42, GP43 and GP61
SMI_STS5 and SMI_EN5 for GP54-GP57, FAN_TACH1 and FAN_TACH2
SMSC DS – LPC47M14X
Page 113
Rev. 03/19/2001
The following GPIOs have “either edge triggered interrupt” (EETI) input capability. These GPIOs can generate a
PME and an SMI on both a high-to-low and a low-to-high edge on the GPIO pin. These GPIOs have a status bit in
the MSC_STS status register that is set on both edges. The corresponding bits in the PME and SMI status registers
are also set on both edges.
ꢀ
ꢀ
ꢀ
GP21, GP22
GP41, GP43
GP60, GP61
The following table summarizes the PME and SMI functionality for each GPIO. It also shows the Either Edge
Triggered Interrupt (EETI) input capability for the GPIOs and the power source for the buffer on the I/O pads.
GPIO
PME
SMI
EETI
BUFFER
POWER
NOTES
GP10-GP17
GP20-GP22, GP24-GP26
GP27
GP30, GP31
GP32, GP33
GP35
GP36, GP37
GP40
GP41
GP42
GP43
GP50-GP52
GP53
Yes
Yes
Yes
Yes
Yes
No
No
No
No
Yes
nIO_SMI
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
GP21, GP22
No
VCC
VCC
VCC
VCC
VCC
VTR
VCC
VCC
VCC
VTR
VCC
VCC
VTR
VCC
VTR
4
4
4
4
5
1
2
2
4
No
No
No
No
No
Yes
No
Yes
No
No
Yes
nIO_PME
Yes
Yes
Yes
4, 6
4
1, 5
4
No
Yes
Yes
GP54-GP57
GP60, GP61
Yes
Yes
No
Yes
3, 4
Note 1: GP35 and GP53 have the IRTX function and their output buffers are powered by VTR so that the
pins are always forced low when not used.
Note 2: GP36-GP37 and GP40 should not be connected to any VTR powered external circuitry. These
pins are not used for wakeup.
Note 3: GP60 and GP61 have LED functionality which must be active under VTR so its buffer is
powered by VTR.
Note 4: These pins can be used for wakeup events to generate a PME while the part is under VTR power
(VCC=0).
Note 5: These pins cannot be used for wakeup events to generate a PME while the part is under VTR power
(VCC=0). The GP32, GP33 and GP53 pins come up as output and low on a VCC POR and hard reset.
Also, GP32 and GP33 pins revert to their non-inverting GPIO input function when VCC is removed from the
part.
Note 6: GP43 defaults to the GPIO function on VCC POR and Hard Reset.
6.14.6 Either Edge Triggered Interrupts
Six GPIO pins are implemented such that they allow an interrupt (PME or SMI) to be generated on both a high-to-low
and a low-to-high edge transition, instead of one or the other as selected by the polarity bit.
The either edge triggered interrupts (EETI) function as follows: If the EETI function is selected for the GPIO pin, then
the bits that control input/output, polarity and open collector/push-pull have no effect on the function of the pin.
However, the polarity bit does affect the value of the GP bit (i.e., register GP2, bit 2 for GP22).
A PME or SMI interrupt occurs if the PME or SMI enable bit is set for the corresponding GPIO and the EETI function
is selected on the GPIO. The PME or SMI status bits are set when the EETI pin transitions (on either edge) and are
cleared on a write of ‘1’. There are also status bits for the EETIs located in the MSC_STS register, which are also
cleared on a write of ‘1’. The MSC_STS register provides the status of all of the EETI interrupts within one register.
The PME, SMI or MSC status is valid whether or not the interrupt is enabled and whether or not the EETI function is
selected for the pin.
SMSC DS – LPC47M14X
Page 114
Rev. 03/19/2001
Miscellaneous Status Register (MSC_STS) is for the either edge triggered interrupt status bits. If the EETI function is
selected for a GPIO then both a high-to-low and a low-to-high edge will set the corresponding MSC status bits.
Status bits are cleared on a write of ‘1’. See the “Runtime Registers” section for more information.
The configuration register for the either edge triggered interrupt status bits is defined in the “Runtime Registers”
section.
6.14.7 LED Functionality
The LPC47M14x provides LED functionality on two GPIOs, GP60 and GP61. These pins can be configured to turn
the LED on and off and blink independent of each other through the LED1 and LED2 runtime registers at offset 0x5D
and 0x5E from the base address located in the primary base I/O address in Logical Device A.
The LED pins (GP60 and GP61) are able to control the LED while the part is under VTR power with VCC removed.
In order to control an LED while the part is under VTR power, the GPIO pin must be configured for the LED function
and either open drain or push-pull buffer type. In the case of open-drain buffer type, the pin is capable of sinking
current to control the LED. In the case of push-pull buffer type, the part will source current. The part is also able to
blink the LED under VTR power, since the external 32kHz clock is always connected.
The LED pins can drive an LED when the buffer type is configured to be push-pull and the part is powered by either
VCC or VTR, since the buffers for these pins are powered by VTR. This means they will source their specified current
from VTR even when VCC is present.
The LED control registers are defined in the “Runtime Registers” section.
6.15 SYSTEM MANAGEMENT INTERRUPT (SMI)
The LPC47M14x implements a “group” nIO_SMI output pin. The System Management Interrupt is a non-maskable
interrupt with the highest priority level used for OS transparent power management. The nSMI group interrupt output
consists of the enabled interrupts from each of the functional blocks in the chip and many of the GPIOs and the Fan
tachometer pins. The GP27/nIO_SMI pin, when selected for the nIO_SMI function, can be programmed to be active
high or active low via the polarity bit in the GP27 register. The output buffer type of the pin can be programmed to be
open-drain or push-pull via bit 7 of the GP27 register. The nIO_SMI pin function defaults to active low, open-drain
output.
The interrupts are enabled onto the group nSMI output via the SMI Enable Registers 1 to 5. The nSMI output is then
enabled onto the group nIO_SMI output pin via bit[7] in the SMI Enable Register 2. The SMI output can also be
enabled onto the serial IRQ stream (IRQ2) via Bit[6] in the SMI Enable Register 2. The internal SMI can also be
enabled onto the nIO_PME pin. Bit[5] of the SMI Enable Register 2 is used to enable the SMI output onto the
nIO_PME pin (GP42). This bit will enable the internal SMI output into the PME logic through the DEVINT_STS bit in
PME_STS3. See PME section for more details.
An example logic equation for the nSMI output for SMI registers 1 and 2 is as follows:
nSMI = (EN_PINT and IRQ_PINT) or (EN_U2INT and IRQ_U2INT) or (EN_U1INT and IRQ_U1INT) or (EN_FINT and
IRQ_FINT) or (EN_MINT and IRQ_MINT) or (EN_KINT and IRQ_KINT) or (EN_IRINT and IRQ_IRINT)
6.15.1 SMI Registers
The SMI event bits for the GPIOs and the Fan tachometer events are located in the SMI status and Enable registers
3-5. The polarity of the edge used to set the status bit and generate an SMI is controlled by the polarity bit of the
control registers. For non-inverted polarity (default) the status bit is set on the low-to-high edge. If the EETI function
is selected for a GPIO then both a high-to-low and a low-to-high edge will set the corresponding SMI status bit.
Status bits for the GPIOs are cleared on a write of ‘1’.
The SMI logic for these events is implemented such that the output of the status bit for each event is combined with
the corresponding enable bit in order to generate an SMI.
The SMI registers are accessed at an offset from PME_BLK (see “Runtime Registers” section for more information).
The SMI event bits for the super I/O devices are located in the SMI status and enable register 1 and 2. All of these
status bits are cleared at the source except for IRINT, which is cleared by a read of the SMI_STS2 register; these
status bits are not cleared by a write of ‘1’. The SMI logic for these events is implemented such that each event is
directly combined with the corresponding enable bit in order to generate an SMI.
See the “Runtime Registers” section for the definition of these registers.
SMSC DS – LPC47M14X
Page 115
Rev. 03/19/2001
6.16 PME SUPPORT
The LPC47M14x offers support for power management events (PMEs), also referred to as a System Control Interrupt
(SCI) events in an ACPI system. A power management event is indicated to the chipset via the assertion of the
nIO_PME signal. In the LPC47M14x, the nIO_PME is asserted by active transitions on the ring indicator inputs nRI1
and nRI2, valid NEC infrared remote control frames, active keyboard-data edges, active mouse-data edges,
programmable edges on GPIO pins and fan tachometer event. The GP42/nIO_PME pin, when selected for the
nIO_PME function, can be programmed to be active high or active low via the polarity bit in the GP42 register. The
output buffer type of the pin can be programmed to be open-drain or push-pull via bit 7 of the GP42 register. The
nIO_PME pin function defaults to active low, open-drain output.
The PME functionality is controlled by the PME status and enable registers in the runtime registers block, which is
located at the address programmed in configuration registers 0x60 and 0x61 in Logical Device A. The PME Enable
bit, PME_EN, globally controls PME Wake-up events. When PME_EN is inactive, the nIO_PME signal can not be
asserted. When PME_EN is asserted, any wake source whose individual PME Wake Enable register bit, is asserted
can cause nIO_PME to become asserted.
The PME Wake Status register indicates that an enabled wake source has occurred, and if the PME_EN bit is set,
asserted the nIO_PME signal. The PME Status bit is asserted by active transitions of PME Wake sources.
PME_Status will become asserted independent of the state of the global PME enable bit, PME_En.
The following pertains to the PME status bits for each event:
ꢀ
ꢀ
The output of the status bit for each event is combined with the corresponding enable bit to set the PME
status bit.
The status bit for any pending events must be cleared in order to clear the PME_STS bit.
For the GPIO events, the polarity of the edge used to set the status bit and generate a PME is controlled by the
polarity bit of the GPIO control register. For non-inverted polarity (default) the status bit is set on the low-to-high
edge. If the EETI function is selected for a GPIO then both a high-to-low and a low-to-high edge will set the
corresponding PME status bits. Status bits are cleared on a write of ‘1’.
The PME Wake registers also include status and enable bits for the fan tachometer input.
See the “Keyboard and Mouse PME Generation” section for information about using the keyboard and mouse signals
to generate a PME.
In the LPC47M14x the nIO_PME pin can be programmed to be an open drain, active low, driver. The LPC47M14x
nIO_PME pin is fully isolated from other external devices that might pull the nIO_PME signal low; i.e., the nIO_PME
signal is capable of being driven high externally by another active device or pullup even when the LPC47M14x VCC
is grounded, providing VTR power is active. The LPC47M14x nIO_PME driver sinks 6mA at .55V max (see section
4.2.1.1 DC Specifications, page 122, in the “PCI Local Bus Specification,” revision 2.1).
ꢀ
The PME registers are run-time registers as follows. These registers are located in system I/O space at an offset
from PME_BLK, the address programmed in Logical Device A at registers 0x60 and 0x61.
The following registers are for GPIO wakeup events:
ꢀ
ꢀ
ꢀ
ꢀ
PME Wake Status 2 (PME_STS2), PME Wake Enable 2 (PME_EN2)
PME Wake Status 3 (PME_STS3), PME Wake Enable 3 (PME_EN3)
PME Wake Status 4 (PME_STS4), PME Wake Enable 4 (PME_EN4)
PME Wake Status 5 (PME_STS5), PME Wake Enable 5 (PME_EN5)
See PME register description in the “Runtime Registers” Section.
SMSC DS – LPC47M14X
Page 116
Rev. 03/19/2001
Enabling SMI Events onto the PME Pin
There is a bit in the PME Status Register 3 to show the status of the internal “group” SMI signal in the PME logic (if bit
5 of the SMI_EN2 register is set). This bit, DEVINT_STS, is at bit 3 of the PME_STS3 register. This bit is defined as
follows:
0=The group SMI output is inactive.
1=The group SMI output is active.
Note: Bit 5 of the SMI_EN2 register must also be set. This bit is cleared on a write of ‘1’.
There is a bit in the PME Enable Register 3 to enable the SMI onto the nIO_PME pin (if the nIO_PME function is
selected for GP42). This bit, DEVINT_EN, is at bit 3 of the PME_EN3 register. This bit will enable the internal “group”
SMI signal (if bit 5 of the SMI_EN2 register is set) into the PME logic through the DEVINT_STS bit as follows: If the
DEVINT_EN bit is ‘1’ and the DEVINT_STS bit is ‘1’ then the nIO_PME pin will be active. This pin has its polarity
controlled by the polarity bit in the GP42 register.
This bit is defined as follows:
0=Disable group SMI output from the nIO_PME pin.
1=Enable group SMI output onto the nIO_PME pin. That is, if this bit is set and the DEVINT_STS bit is set
then a nPME is generated.
Note: Bit 5 of the SMI_EN2 register must also be set.
6.16.1 ‘Wake on Specific Key’ Option
The LPC47M14x has logic to detect a single keyboard scan code for wakeup (PME generation). The scan code is
programmed onto the Keyboard Scan Code Register, a runtime register at offset 0x5F from the base address located
in the primary base I/O address in Logical Device A. This register is powered by VTR and reset on VTR POR.
The PME status bit for this event is located in the PME_STS1 register at bit 5 and the PME enable bit for this event is
located in the PME_EN1 register at bit 5. See the “Runtime Registers” section for a definition of these registers.
Data transmissions from the keyboard consist of an 11-bit serial data stream. A logic 1 is sent at an active high level.
The following table shows the functions of the bits.
BIT
1
2
FUNCTION
Start bit (always 0)
Data bit 0 (least significant bit)
Data bit 1
3
4
5
Data bit 2
Data bit 3
6
7
Data bit 4
Data bit 5
8
9
10
11
Data bit 6
Data bit 7 (most significant bit)
Parity bit (odd parity)
Stop Bit (always 1)
The timing for the keyboard clock and data signals are shown in the “Timing Diagrams” section.
The process to find a match for the scan code stored in the Keyboard Scan Code register is as follows:
Begin sampling the data at the first falling edge of the keyboard clock following a period where the clock line has
been high for 115-145usec. The data at this first clock edge is the start bit. The first data bit follows the start bit (clock
2). Sample the data on each falling edge of the clock. Store the eight bits following the stop bit to compare with the
scan code stored in the Keyboard Scan Code register. Sample the comparator within 100usec of the falling edge of
clock 9 (for example, at clock 10).
Sample the parity bit and check that the 8 data bits plus the parity bit always have an odd number of 1’s (odd parity).
Repeat until a match is found. If the 8 data bits match the scan code stored in the Keyboard Scan Code register and
the parity is correct, then it is considered a match. When a match is found and if the stop bit is 1, set the event status
bit (bit 5 of the PME_STS1 register) to ‘1’ within 100usec of the falling edge of clock 10.
SMSC DS – LPC47M14X
Page 117
Rev. 03/19/2001
The state machine will reset after 11 clocks and the process will restart. The process will continue until it is shut off by
setting the SPEKEY_EN bit (see following sub-section).
The state machine will reset if there is a period where the clock remains high for more than one keyboard clock
period (115-145usec) in the middle of the transmission (i.e., before clock 11). This is to prevent the generation of a
false PME.
The SPEKEY_EN bit at bit 1 of the CLOCKI32 register at 0xF0 in Logical Device A is used to control the “wake-on-
specific feature. This bit is used to turn the logic for this feature on and off. It will disable the 32kHz clock input to the
logic. The logic will draw no power when disabled. The bit is defined as follows:
0= “Wake on specific key” logic is on (default)
1= “Wake on specific key” logic is off
Note: The generation of a PME for this event is controlled by the PME enable bit (located in the PME_EN1 register
at bit 5) when the logic for feature is turned on.
6.17 FAN SPEED CONTROL AND MONITORING
The LPC47M14x implements fan speed control outputs and fan tachometer inputs. The implementation of these
features are described in the sections below.
6.17.1 Fan Speed Control
The fan speed control for the LPC47M14x is implemented as pulse width modulators with fan clock speed selection.
Pins 54 and 55 are the fan speed control outputs, FAN2 and FAN1, respectively, muxed with GPIOs. These fan
control pins come up as outputs and are low following a VCC POR and Hard Reset. These pins may not be used for
wakeup events under VTR power (VCC=0).
The configuration registers are defined in the “Runtime Registers” section.
Fan Speed Control Summary
The following table illustrates the different modes for the fans.
Table 57 – Different Modes for Fan
FANX CLOCK
CONTROL
BIT
FANX
FANX
CLOCK
SOURCE
SELECT
BIT
FANX
CLOCK
SELECT
BIT (NOTE
4)
6-BIT DUTY
CYCLE
CLOCK
MULTIPLIER
BIT
FOUT
DUTY CYCLE
(%)
CONTROL
(NOTE 1)
BITS[6:1]
(DCC)
(NOTE 2)
(NOTE 3)
0
0
0
0
0
0
0
0
0
1
X
0
0
0
0
1
1
1
1
X
X
0
0
1
1
0
0
1
1
X
X
0
1
0
1
0
1
0
1
X
0Hz – LOW
15.625kHz
23.438kHz
40Hz
0
1-63
-
(DCC/64)
• 100
60Hz
31.25kHz
46.876kHz
80Hz
120Hz
0Hz – HIGH
-
-
Note 1: This is FANx Register Bit 0
Note 2: This is Fan Control Register Bit 2 or 3
Note 3: This is Fan Control Register Bit 0 or 1
Note 4: This is FANx Register Bit 7
SMSC DS – LPC47M14X
Page 118
Rev. 03/19/2001
FANx Registers
The FAN1 and FAN2 Registers are located at 0x56 and 0x57 from base I/O in Logical Device A. The bits are defined
below. See the register description in the “Runtime Registers” section.
Fan x Clock Select Bit, D7
The Fan x Clock select bit in the FANx registers is used with the Fan x Clock Source Select and the Fan x Clock
Multiplier bits in the Fan Control register to determine the fan speed FOUT. See Table 57 above.
Duty Cycle Control for Fan x, Bits D6 – D1
The Duty Cycle Control (DCC) bits determine the fan duty cycle. The LPC47M14x has ≈1.56% duty cycle resolution.
When DCC = “000000” (min. value), FOUT is always low. When DCC is “111111” (max. value), FOUT is almost always
high; i.e., high for 63/64th and low for 1/64th of the FOUT period.
Generally, the FOUT duty cycle (%) is (DCC ÷ 64) × 100.
Fan x Clock Control, Bit D0
The Fan x Clock Control bit D0 is used to override the Duty Cycle Control for Fan x bits and force FOUT always high.
When D0 = “0”, the DCC bits determine the FOUT duty cycle. When D0 = 1, FOUT is always high, regardless of the
state of the DCC bits.
Fan Control Register
The Fan Control Register is located at 0x58 from base I/O in Logical Device A. The bits are defined below. See the
register description in the “Runtime Registers” section.
Fan x Count Divisor, Bits D7-D6 / D5-D4
Fan x Count Divisor bit in Fan Control Register is used to determine fan tachometer count. The choices for the
divisor are 1, 2, 4 and 8. See “Fan Tachometer Input” section.
Fan x Clock Multiplier, Bits D3 / D2
The Fan x Clock Multiplier bit is used with the Fan x Clock Source Select bit in the Fan Control Register and the Fan
x Clock Select bit in Fan register to determine the FOUT
.
When the Fan x Clock Multiplier bit = “0”, no clock multiplier is used. When the Fan x Clock Multiplier bit = “1”, the
clock speed determined by the Fan x Clock Source Select bit is doubled.
Fan x Clock Source Select, Bits D1 / D0
The Fan x Clock Source Select and the Fan x Clock Multiplier bits in the Fan Control register is used with the Fan x
Clock Select bit in the Fan x registers to determine the fan speed FOUT. See Table 57 above.
6.17.2 Fan Tachometer Inputs
The LPC47M14x implements fan tachometer inputs for signals from fans equipped with tachometer outputs. The part
can generate both a PME and an SMI when the fan speed drops below a predetermined value. See description
below.
The clock source for the tachometer count is the 32.768kHz oscillator. The Fan Tachometer Inputs gate a divided
down version of the 32.768kHz oscillator for one period of the Fan signal into an 8-bit counter (maximum count is
255).
SMSC DS – LPC47M14X
Page 119
Rev. 03/19/2001
The fan tachometer input signal and clock source is shown below.
TR
Fan
Tachometer
Input
TP
TR = Revolution Time = 60/RPM (sec)
TP = Pulse Time = TR/2
(Two Pulses Per Revolution)
Clock Source
for Counter
F = 32.786kHz ÷ Divisor
The counter is reset by the rising edge of each pulse (and by writing the preload register). The counter does not
wrap; if it reaches 0xFF, it remains at 0xFF until it is reset by the next pulse.
The 2 MSBs of the count are sampled and a PME or SMI is generated (if enabled through the PME_EN1 enable
register or the SMI_EN5 enable register - see the “Runtime Registers” section) when these two bits are set. This
corresponds to a count value of 192.
The fan count is determined according to the following equation:
Count =
1
2
x
1.966 x 106
+ Preload (Equation 1)
RPM x Divisor
(Term 1)
Term 1 in the equation above is determined by multiplying the clock source of 32.768kHz by 60sec/min and dividing
by the product of the revolutions per minute times the divisor. The default divisor, located in the Fan Control
Register, is 2. This results in a value for Term 1 in Equation 1 of 111 for a 4400 RPM.
The divisor for each fan is programmable via the Fan Control Register, which is located in the Runtime Register block
at offset 0xFA. The choices for the divisor are 1, 2, 4 and 8. The default value is 2. The factor of ½ in Term 1
corresponds to two pulses per revolution.
The preload value is programmable via the FAN1 Preload Register and FAN2 Preload Register. The preload is the
initial value for the fan count which is used to adjust the count such that the value of 192 corresponds to the “lower
limit” of the RPM. By setting the preload value and divisor properly, the PME or SMI will be generated when the RPM
reaches the desired percentage of the nominal RPM to indicate a fan failure.
A PME or SMI is generated, if enabled through the PME or SMI enable register, at a count of 192, which corresponds
to the “upper limit” for the fan count. This value is made to correspond to the “lower limit” of the RPM for the fan by
programming the divisor and preload value accordingly. Typical practice is to consider 70% of normal RPM a fan
failure, at which point Term 1 in Equation 1 for the example above will be 160. Therefore, the preload value is
chosen to be 32 so that when the count reaches 192, this will correspond to 70% of the normal RPM for the
generation of a PME or SMI.
SMSC DS – LPC47M14X
Page 120
Rev. 03/19/2001
A representation of the logic for the fan tachometer implementation is shown below.
Preload
Programmable
Divider
32 kHz
Counter
1, 2, 4, 8
MSB
To nPME
Logic
Sync
Latch on Read
The following tables show examples of the desired functionality. Counts are based on 2 pulses per revolution
tachometer outputs with a default divisor of 2.
TERM 1 FOR “DIVIDE
BY 2” (DEFAULT) IN
DECIMAL
COUNT =
TIME PER
(TERM 1) +
REVOLUTION
PRELOAD
RPM
4400
3080
2640
2204
PRELOAD
COMMENTS
Typical RPM
70% RPM
60% RPM
50% RPM
13.64 ms
19.48 ms
22.73 ms
27.22 ms
112 counts
160 counts
186 counts
223 counts
32
32
32
32
144
192
218
255
(maximum count)
COUNTS FOR
THE GIVEN
SPEED IN
DECIMAL
TIME PER
REVOLUTION
FOR 70% RPM
MODE
NOMINAL
RPM
TIME PER
SELECT
REVOLUTION
PRELOAD
70% RPM
6160
Divide by 1
Divide by 2
Divide by 4
Divide by 8
8800
4400
2200
1100
6.82 ms
13.64 ms
27.27 ms
54.54 ms
32
32
32
32
144
144
144
144
9.74 ms
19.48 ms
38.96 ms
77.92 ms
3080
1540
770
Pins 51 and 52 are the fan tachometer inputs, FAN_TACH2 and FAN_TACH1, respectively.
The configuration registers for the fan tachometer inputs are defined in the “Runtime Registers” section.
SMSC DS – LPC47M14X
Page 121
Rev. 03/19/2001
6.18 SECURITY FEATURE
The following register describes the functionality to support security in the LPC47M14x.
6.18.1 GPIO Device Disable Register Control
The GPIO pin GP43 is used for the Device Disable Register Control (DDRC) function. Setting bits[3:2] of the GP43
configuration register to ‘01’, selects the DDRC function for the GP43 pin. When bits[3:2]=01 the GP43 pin is an
input, with non-inverted polarity. Bits[3:2] cannot be cleared by writing to these bits; they are cleared by VTR POR,
VCC POR and Hard Reset. That is, when the DDRC function is selected for this pin, it cannot be changed, except by a
VCC POR, hard reset or VTR POR.
When the DDRC function is selected for GP43, the Device Disable register is controlled by the value of the GP43 pin
as follows:
ꢀ
ꢀ
If the GP43 pin is high, the Device Disable Register is Read-Only.
If the GP43 pin is low, the Device Disable Register is Read/Write.
6.18.2 Device Disable Register
The Device Disable Register is located in the PME register block at offset 0x22 from the PME_BLK base I/O address
in logical device A. Writes to this register are blocked when the GP43 pin is configured for the Device Disable
Register Control function (GP43 configuration register bit 2 =1) and the GP43 pin is high.
The configuration register for the device disable register is defined in the “Runtime Registers” section.
6.19 GAME PORT LOGIC
The LPC47M14x implements logic to support a dual game port. This logic includes the following for each game port:
two 555 timers, two game port RC constant inputs (x-axis and y-axis), two game port button inputs and game port
interface logic. The implementation of the Game Port uses a simple A/D converter constructed from a 555 timer to
digitize the analog value of a potentiometer for the x-axis and y-axis of the joystick.
The figure below illustrates the implementation of the game port logic in the LPC47M14x.
Internal To Joysticks
Internal To LPC47M14x
Vcc = 5V
Joystick 1
Vcc = 5V
556
J1X
J1Y
X-Axis
Y-Axis
TIM1A
OUT1A
OUT1B
TIM1B
JOYW
TRIG1A
TRIG1B
D0
D1
D2
D3
Vcc = 5V
Joystick 2
556
J2X
J2Y
X-Axis
TIM2A
OUT2A
OUT2B
Vcc = 5V
Y-Axis
JOYR
Game Port
Register
TIM2B
Vcc = 5V
TRIG2A
TRIG2B
J1B1
J1B2
J2B1
J2B2
Joystick 1 Button 1
Joystick 1 Button 2
Joystick 2 Button 1
Joystick 2 Button 2
D4
D5
D6
D7
Game software will write a byte to the game port to reset it, and then poll (read) the port until the x and y-axis RC time
constant pins (TIMA,B) time out (return to zero). The elapsed time indicates the resistance value of the potentiometer
and in turn, the position of the joystick.
SMSC DS – LPC47M14X
Page 122
Rev. 03/19/2001
The figure below illustrates the timing of the game port signals. The 556 timers will reset the outputs (OUTA,B) to
zero and the RC constant (TIMA,B) pins to zero when the RC constant (TIMA,B) inputs reach 2/3 of VREF as shown.
VREF is the voltage on pin 44, which is either 5V or 3.3V. See the “VREF Pin “ section.
JOYW
VREF
2
3
VREF
TIMA,B
t1
OUTA,B
JOYR
The game port register is defined below. It is a runtime register located at the address programmed into the base I/O
address (GAME_PORT) in Logical Device 9.
Note: Register 0x60 is the high byte; 0x61 is the low byte. For example, to set the primary base address to
1234h, write 12h into 0x60, and 34h into 0x61.
When the activate bit in Logical Device 9 is cleared, it prevents the base I/O address for the game port from being
decoded.
SMSC DS – LPC47M14X
Page 123
Rev. 03/19/2001
Game Port Register
Register Location:
Default Value:
Attribute:
<GAME_PORT>+0h
00h
System I/O Space
on
VTR POR
Read-Only
8-bits
Size:
D7
D6
D5
D4
D3
D2
D1
D0
Button #2 Button #1 Button #2 Button #1
Y-Axis
X-Axis
Y-Axis
X-Axis
Joystick 2 Joystick 2 Joystick 1 Joystick 1 Joystick 2 Joystick 2 Joystick 1 Joystick 1
(J2B2)
(J2B1)
(J1B2)
(J1B1)
(OUT2B)
(OUT2A)
(OUT1B)
(OUT1A)
The game port register is a read-only register. However, writing to the game port resets the RC time constant pins
(TIMA,B) to zero. The reset of the time constant pins occur on the “back” edge of the write signal (when the write
signal goes from its active state to its inactive state).
The game port read (JOYR) will be an IO read to the address programmed into the base IO address in Logical
Device 9.
The game port write (JOYW) will be an IO write to the address programmed into the base IO address in Logical
Device 9.
Minimum Rise Time
The fastest rise time on the RC constant pins (minimum RC time constant) for the game port is 20usec.
6.19.1 Power Control Register
Bit 2 in the Power Control Register (CR22) is the power control bit for the game port. This bit has the same function
as the activate bit for logical device 9 and shadows the activate bit. The activate bit also shadows the power control
bit 2.
6.19.2 VREF Pin
The LPC47M14x has a reference voltage pin input on pin 44 of the part. This reference voltage can be connected to
either a 5V supply or a 3.3V supply. It is used for the game port.
The reference voltage is used in the game port logic so that the joystick trigger voltage is 2/3 VREF where VREF is
either 5V or 3.3V. This is to preserve joystick compatibility by maintaining the RC time constant reset trigger voltage
of 3.3V (nominal) with VREF=5V (nominal), if required.
SMSC DS – LPC47M14X
Page 124
Rev. 03/19/2001
7
RUNTIME REGISTERS
The following registers are runtime registers in the LPC47M14x. They are located at the address programmed in the
Base I/O Address in Logical Device A (also referred to as the PME register) at the offset shown. These registers are
powered by VTR.
Table 58 – Runtime Register Block Summary
REGISTER
OFFSET
HARD
SOFT
(hex)
RESET
RESET
TYPE
R/W
R
R/W
R
R/W
R/W
R/W
R/W
R/W
R
R/W
R/W
R/W
R/W
R/W
R
R/W
R/W
R/W
R/W
R/W
R
R/W
R/W
R/W
R/W
R/W
R
VCC POR
VTR POR
REGISTER
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0x00
-
0x00
-
0x00
0x00
0x00
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
PME_STS
Reserved – reads return 0
PME_EN
Reserved – reads return 0
PME_STS1
PME_STS2
PME_STS3
PME_STS4
PME_STS5
Reserved – reads return 0
0x00 (Note 5)
0x00 (Note 5)
-
0x00
0x00
0x00
0x00
0x00
-
PME_EN1
PME_EN2
PME_EN3
PME_EN4
PME_EN5
Reserved – reads return 0
SMI_STS 1
Note 4
Note 4
0x02 (Note 4)
(Note 4)
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0x00
0x00
0x00 (Note 5)
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
SMI_STS 2
SMI_STS3
SMI_STS4
SMI_STS5
0x00
-
0x00
0x00
0x00
0x00
0x00
-
0x00
-
-
-
-
-
Reserved – reads return 0
SMI_EN1
SMI_EN2
SMI_EN3
SMI_EN4
SMI_EN5
Reserved – reads return 0
MSC_STS
R/W
R
R/W
R
R
-
-
Reserved – reads return 0
Force Disk Change
Floppy Data Rate Select Shadow
UART1 FIFO Control Shadow
UART2 FIFO Control Shadow
Device Disable Register
0x01
0x01
-
-
-
-
-
-
-
-
R
R/W
0x00
(Note 1)
23
24
25
26
27
28
R/W
R/W
R/W
R/W
R/W
R/W
-
-
-
-
-
-
-
-
-
-
-
-
0x01
0x01
0x01
0x01
0x01
0x01
-
-
-
-
-
-
GP10
GP11
GP12
GP13
GP14
GP15
SMSC DS – LPC47M14X
Page 125
Rev. 03/19/2001
REGISTER
OFFSET
HARD
SOFT
(hex)
RESET
RESET
TYPE
R/W
R/W
R/W
R/W
R/W
R
VCC POR
VTR POR
0x01
0x01
0x01
0x01
0x01
-
REGISTER
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
GP16
GP17
GP20
GP21
GP22
Reserved – reads return 0
GP24
GP25
GP26
GP27
GP30
GP31
GP32
GP33
GP34
GP35
GP36
GP37
GP40
GP41
GP42
GP43
GP50
GP51
GP52
GP53
GP54
GP55
GP56
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
0x01
0x01
0x01
0x01
0x01
0x01
0x01
0x01
0x05
0x04
0x01
0x01
0x01
0x01
0x01
0x01
0x01
0x01
0x01
0x00
0x01
0x01
0x01
0x01
0x01
0x01
-
0x00
0x00
-
0x04
-
-
-
0x00
0x00
-
0x04
-
-
-
-
-
-
-
(Note 2)
(Note 2)
-
-
-
-
-
-
0x00
-
-
-
-
-
-
-
0x00
-
-
-
-
-
-
-
GP57
GP60
GP61
Reserved – reads return 0
Reserved – reads return 0
GP1
GP2
GP3
GP4
GP5
GP6
Reserved – reads return 0
Reserved – reads return 0
Reserved – reads return 0
Interrupt Generating Register 1
Interrupt Generating Register 2
FAN1
FAN2
Fan Control
Fan1 Tachometer Register
R
-
-
-
-
-
-
-
R/W
R/W
R/W
R/W
R/W
R/W
R
0x00
0x00
0x00
0x00
0x00
0x00
-
-
-
-
-
(Note 2)
(Note 2)
-
-
(Note 3)
(Note 3)
-
-
-
-
-
-
-
-
R
R
R/W
R/W
R/W
R/W
R/W
R
0XFF
0XFF
-
-
-
-
0XFF
0XFF
-
-
-
-
0x00
0x00
0x50
0x00
SMSC DS – LPC47M14X
Page 126
Rev. 03/19/2001
REGISTER
OFFSET
HARD
SOFT
(hex)
5A
5B
5C
5D
5E
5F
60-7F
RESET
RESET
TYPE
R
VCC POR
VTR POR
0x00
0x00
0x00
0x00
0x00
0x00
-
REGISTER
Fan2 Tachometer Register
Fan1 Preload Register
Fan2 Preload Register
LED1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
R/W
R/W
R/W
R/W
R/W
R
LED2
Keyboard Scan Code
Reserved – reads return 0
Note 1: This register is read-only when GP43 register bit [3:2] = 01 and the GP43 pin is high.
Note 2: Bits [3:2] of this register are reset (cleared) on VCC POR and Hard Reset (and VTR POR).
Note 3: Bit 3 of this register is reset (cleared) on VCC POR and Hard Reset (and VTR POR).
Note 4: The parallel port interrupt defaults to 1 when the parallel port activate bit is cleared.
Note 5: Bits 2 and 3 of the PME_STS4 and SMI_STS4 registers, and bit 3 of the PME_STS5 register may be set on a
VCC POR. If GP32, GP33 and GP53 are configured as input, then their corresponding PME and SMI status bits will be
set on a VCC POR Also, GP32 and GP33 pins revert to their non-inverting GPIO input function when VCC is removed
from the part. These GPIOs cannot be used for PME wakeup when the part is under VTR power (VCC=0).
The following registers are located at an offset from (PME_BLK) the address programmed into the base I/O address
register for Logical Device A.
Table 59 – PME, SMI, GPIO, FAN Register Description
REG OFFSET
(hex)
NAME
PME_STS
DESCRIPTION
00
Bit[0] PME_Status
= 0 (default)
Default = 0x00
on VTR POR
(R/W)
= 1 Set when LPC47M14x would normally assert the
nIO_PME signal, independent of the state of the
PME_En bit.
Bit[7:1] Reserved
PME_Status is not affected by Vcc POR, SOFT RESET
or HARD RESET.
Writing a “1” to PME_Status will clear it and cause the
LPC47M14x to stop asserting nIO_PME, in enabled.
Writing a “0” to PME_Status has no effect.
N/A
01
(R)
02
Reserved – reads return 0
PME_EN
Bit[0] PME_En
= 0 nIO_PME signal assertion is disabled (default)
= 1 Enables LPC47M14x to assert nIO_PME signal
Bit[7:1] Reserved
Default = 0x00
on VTR POR
(R/W)
PME_En is not affected by Vcc POR, SOFT RESET or
HARD RESET
Reserved – reads return 0
N/A
03
(R)
SMSC DS – LPC47M14X
Page 127
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
PME_STS1
DESCRIPTION
PME Wake Status Register 1
04
This register indicates the state of the individual PME
wake sources, independent of the individual source
enables or the PME_En bit.
Default = 0x00
on VTR POR
(R/W)
If the wake source has asserted a wake event, the
associated PME Wake Status bit will be a “1”.
Bit[0] Reserved (Note 7)
Bit[1] RI2
Bit[2] RI1
Bit[3] KBD
Bit[4] MOUSE
Bit[5] SPEKEY (Wake on specific key)
Bit[6] FAN_TACH1
Bit[7] FAN_TACH2
The PME Wake Status register is not affected by Vcc
POR, SOFT RESET or HARD RESET.
Writing a “1” to Bit[7:0] will clear it. Writing a “0” to any
bit in PME Wake Status Register has no effect.
PME Wake Status Register 2
PME_STS2
05
This register indicates the state of the individual PME
wake sources, independent of the individual source
enables or the PME_En bit.
Default = 0x00
on VTR POR
(R/W)
If the wake source has asserted a wake event, the
associated PME Wake Status bit will be a “1”.
Bit[0] GP10
Bit[1] GP11
Bit[2] GP12
Bit[3] GP13
Bit[4] GP14
Bit[5] GP15
Bit[6] GP16
Bit[7] GP17
The PME Wake Status register is not affected by Vcc
POR, SOFT RESET or HARD RESET.
Writing a “1” to Bit[7:0] will clear it. Writing a “0” to any
bit in PME Wake Status Register has no effect.
PME Wake Status Register 3
PME_STS3
06
This register indicates the state of the individual PME
wake sources, independent of the individual source
enables or the PME_En bit.
Default = 0x00
on VTR POR
(R/W)
If the wake source has asserted a wake event, the
associated PME Wake Status bit will be a “1”.
Bit[0] GP20
Bit[1] GP21
Bit[2] GP22
Bit[3] DEVINT_STS (status of group SMI signal for PME)
Bit[4] GP24
Bit[5] GP25
Bit[6] GP26
Bit[7] GP27
The PME Wake Status register is not affected by Vcc
POR, SOFT RESET or HARD RESET.
Writing a “1” to Bit[7:0] will clear it. Writing a “0” to any
bit in PME Wake Status Register has no effect.
SMSC DS – LPC47M14X
Page 128
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
PME_STS4
DESCRIPTION
PME Wake Status Register 4
07
This register indicates the state of the individual PME
wake sources, independent of the individual source
enables or the PME_En bit.
Default = 0x00
on VTR POR
(Note 6)
(R/W)
If the wake source has asserted a wake event, the
associated PME Wake Status bit will be a “1”.
Bit[0] GP30
Bit[1] GP31
Bit[2] GP32
Bit[3] GP33
Bit[4] GP41
Bit[5] GP43
Bit[6] GP60
Bit[7] GP61
The PME Wake Status register is not affected by Vcc
POR, SOFT RESET or HARD RESET.
Writing a “1” to Bit[7:0] will clear it. Writing a “0” to any
bit in PME Wake Status Register has no effect.
PME Wake Status Register 5
PME_STS5
08
This register indicates the state of the individual PME
wake sources, independent of the individual source
enables or the PME_En bit.
Default = 0x00
on VTR POR
(Note 6)
(R/W)
If the wake source has asserted a wake event, the
associated PME Wake Status bit will be a “1”.
Bit[0] GP50
Bit[1] GP51
Bit[2] GP52
Bit[3] GP53
Bit[4] GP54
Bit[5] GP55
Bit[6] GP56
Bit[7] GP57
The PME Wake Status register is not affected by Vcc
POR, SOFT RESET or HARD RESET.
Writing a “1” to Bit[7:0] will clear it. Writing a “0” to any
bit in PME Wake Status Register has no effect.
Reserved – reads return 0
N/A
09
(R)
SMSC DS – LPC47M14X
Page 129
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
PME_EN1
DESCRIPTION
PME Wake Enable Register 1
0A
This register is used to enable individual LPC47M14x
PME wake sources onto the nIO_PME wake bus.
Default = 0x00
on VTR POR
(R/W)
When the PME Wake Enable register bit for a wake
source is active (“1”), if the source asserts a wake event
so that the associated status bit is “1” and the PME_En
bit is “1”, the source will assert the nIO_PME signal.
When the PME Wake Enable register bit for a wake
source is inactive (“0”), the PME Wake Status register
will indicate the state of the wake source but will not
assert the nIO_PME signal.
Bit[0] Reserved (Note 7)
Bit[1] RI2
Bit[2] RI1
Bit[3] KBD
Bit[4] MOUSE
Bit[5] SPEKEY (Wake on specific key)
Bit[6] FAN_TACH1
Bit[7] FAN_TACH2
The PME Wake Enable register is not affected by Vcc
POR, SOFT RESET or HARD RESET.
PME Wake Enable Register 2
PME_EN2
0B
This register is used to enable individual LPC47M14x
PME wake sources onto the nIO_PME wake bus.
Default = 0x00
on VTR POR
(R/W)
When the PME Wake Enable register bit for a wake
source is active (“1”), if the source asserts a wake event
so that the associated status bit is “1” and the PME_En
bit is “1”, the source will assert the nIO_PME signal.
When the PME Wake Enable register bit for a wake
source is inactive (“0”), the PME Wake Status register
will indicate the state of the wake source but will not
assert the nIO_PME signal.
Bit[0] GP10
Bit[1] GP11
Bit[2] GP12
Bit[3] GP13
Bit[4] GP14
Bit[5] GP15
Bit[6] GP16
Bit[7] GP17
The PME Wake Enable register is not affected by Vcc
POR, SOFT RESET or HARD RESET.
SMSC DS – LPC47M14X
Page 130
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
PME_EN3
DESCRIPTION
PME Wake Status Register 3
0C
This register is used to enable individual LPC47M14x
PME wake sources onto the nIO_PME wake bus.
Default = 0x00
on VTR POR
(R/W)
When the PME Wake Enable register bit for a wake
source is active (“1”), if the source asserts a wake event
so that the associated status bit is “1” and the PME_En
bit is “1”, the source will assert the nIO_PME signal.
When the PME Wake Enable register bit for a wake
source is inactive (“0”), the PME Wake Status register
will indicate the state of the wake source but will not
assert the nIO_PME signal.
Bit[0] GP20
Bit[1] GP21
Bit[2] GP22
Bit[3] DEVINT_EN (Enable bit for group SMI signal for
PME)
Bit[4] GP24
Bit[5] GP25
Bit[6] GP26
Bit[7] GP27
The PME Wake Enable register is not affected by Vcc
POR, SOFT RESET or HARD RESET.
PME Wake Enable Register 4
PME_EN4
0D
This register is used to enable individual LPC47M14x
PME wake sources onto the nIO_PME wake bus.
Default = 0x00
on VTR POR
(R/W)
When the PME Wake Enable register bit for a wake
source is active (“1”), if the source asserts a wake event
so that the associated status bit is “1” and the PME_En
bit is “1”, the source will assert the nIO_PME signal.
When the PME Wake Enable register bit for a wake
source is inactive (“0”), the PME Wake Status register
will indicate the state of the wake source but will not
assert the nIO_PME signal.
Bit[0] GP30
Bit[1] GP31
Bit[2] GP32
Bit[3] GP33
Bit[4] GP41
Bit[5] GP43
Bit[6] GP60
Bit[7] GP61
The PME Wake Enable register is not affected by Vcc
POR, SOFT RESET or HARD RESET.
SMSC DS – LPC47M14X
Page 131
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
PME_EN5
DESCRIPTION
PME Wake Enable Register 5
0E
This register is used to enable individual LPC47M14x
PME wake sources onto the nIO_PME wake bus.
Default = 0x00
on VTR POR
(R/W)
When the PME Wake Enable register bit for a wake
source is active (“1”), if the source asserts a wake event
so that the associated status bit is “1” and the PME_En
bit is “1”, the source will assert the nIO_PME signal.
When the PME Wake Enable register bit for a wake
source is inactive (“0”), the PME Wake Status register
will indicate the state of the wake source but will not
assert the nIO_PME signal.
Bit[0] GP50
Bit[1] GP51
Bit[2] GP52
Bit[3] GP53
Bit[4] GP54
Bit[5] GP55
Bit[6] GP56
Bit[7] GP57
The PME Wake Enable register is not affected by Vcc
POR, SOFT RESET or HARD RESET.
Reserved – reads return 0
N/A
0F
(R)
10
SMI_STS1
SMI Status Register 1
This register is used to read the status of the SMI inputs.
The following bits must be cleared at their source.
Bit[0] Reserved
Default = 0x02
on VTR POR
(R/W)
Bit[1] PINT. The parallel port interrupt defaults to ‘1’ when
the parallel port activate bit is cleared. When the parallel
port is activated, PINT follows the nACK input.
Bit 1 is set to ‘1’ on
VCC POR,
Bit[2] U2INT
VTR POR,
Bit[3] U1INT
Bit[4] FINT
Bit[5] MPU-401 INT
Bit[6] Reserved
HARD RESET and
SOFT RESET
Bit[7] Reserved (Note 7)
SMI Status Register 2
This register is used to read the status of the SMI inputs.
Bit[0] MINT. Cleared at source.
Bit[1] KINT. Cleared at source.
SMI_STS2
11
Default = 0x00
on VTR POR
(R/W)
Bit[2] IRINT. This bit is set by a transition on the IR pin
(IRRX or IRRX2 as selected in CR L5-F1-B6 i.e., after the
MUX). Cleared by a read of this register.
Bit[3] Reserved
Bit[4] P12. Cleared at source.
Bit[7:5] Reserved
SMSC DS – LPC47M14X
Page 132
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
SMI_STS3
DESCRIPTION
SMI Status Register 3
12
This register is used to read the status of the SMI inputs.
Default = 0x00
on VTR POR
(R/W)
The following bits are cleared on a write of ‘1’.
Bit[0] GP20
Bit[1] GP21
Bit[2] GP22
Bit[3] Reserved
Bit[4] GP24
Bit[5] GP25
Bit[6] GP26
Bit[7] GP60
SMI_STS4
13
SMI Status Register 4
This register is used to read the status of the SMI inputs.
Default = 0x00
on VTR POR
(Note 6)
(R/W)
The following bits are cleared on a write of ‘1’.
Bit[0] GP30
Bit[1] GP31
Bit[2] GP32
Bit[3] GP33
Bit[4] GP41
Bit[5] GP42
Bit[6] GP43
Bit[7] GP61
SMI_STS5
14
SMI Status Register 5
This register is used to read the status of the SMI inputs.
The following bits are cleared on a write of ‘1’.
Bit[0] GP54
Default = 0x00
on VTR POR
(R/W)
Bit[1] GP55
Bit[2] GP56
Bit[3] GP57
Bit[4] Reserved
Bit[5] Reserved
Bit[6] FAN_TACH1
Bit[7] FAN_TACH2
Reserved – reads return 0
N/A
15
(R)
16
SMI_EN1
SMI Enable Register 1
This register is used to enable the different interrupt
sources onto the group nSMI output.
Default = 0x00
on VTR POR
(R/W)
1=Enable
0=Disable
Bit[0] Reserved
Bit[1] EN_PINT
Bit[2] EN_U2INT
Bit[3] EN_U1INT
Bit[4] EN_FINT
Bit[5] EN_MPU-401 INT
Bit[6] Reserved
Bit[7] Reserved (Note 7)
SMSC DS – LPC47M14X
Page 133
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
SMI_EN2
DESCRIPTION
SMI Enable Register 2
17
This register is used to enable the different interrupt
sources onto the group nSMI output, and the group nSMI
output onto the nIO_SMI GPI/O pin, the serial IRQ stream
or into the PME Logic.
Default = 0x00
on VTR POR
(R/W)
Unless otherwise noted,
1=Enable
0=Disable
Bit[0] EN_MINT
Bit[1] EN_KINT
Bit[2] EN_IRINT
Bit[3] Reserved
Bit[4] EN_P12
Bit[5] EN_SMI_PME (Enable group SMI into PME logic)
Bit[6] EN_SMI_S (Enable group SMI onto serial IRQ)
Bit[7] EN_SMI (Enable group SMI onto nIO_SMI pin)
SMI Enable Register 3
SMI_EN3
18
This register is used to enable the different interrupt
sources onto the group nSMI output.
1=Enable
0=Disable
Default = 0x00
on VTR POR
(R/W)
Bit[0] GP20
Bit[1] GP21
Bit[2] GP22
Bit[3] Reserved
Bit[4] GP24
Bit[5] GP25
Bit[6] GP26
Bit[7] GP60
SMI Enable Register 4
SMI_EN4
19
This register is used to enable the different interrupt
sources onto the group nSMI output.
Default = 0x00
on VTR POR
(R/W)
1=Enable
0=Disable
Bit[0] GP30
Bit[1] GP31
Bit[2] GP32
Bit[3] GP33
Bit[4] GP41
Bit[5] GP42
Bit[6] GP43
Bit[7] GP61
SMSC DS – LPC47M14X
Page 134
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
SMI_EN5
DESCRIPTION
SMI Enable Register 5
1A
This register is used to enable the different interrupt
sources onto the group nSMI output.
Default = 0x00
on VTR POR
(R/W)
1=Enable
0=Disable
Bit[0] GP54
Bit[1] GP55
Bit[2] GP56
Bit[3] GP57
Bit[4] Reserved
Bit[5] Reserved
Bit[6] FAN_TACH1
Bit[7] FAN_TACH2
Reserved – reads return 0
N/A
1B
(R)
1C
MSC_STS
Miscellaneous Status Register
Bits[5:0] can be cleared by writing a 1 to their position
(writing a 0 has no effect).
Default = 0x00
on VTR POR
(R/W)
Bit[0] Either Edge Triggered Interrupt Input 0 Status. This
bit is set when an edge occurs on the GP21 pin.
Bit[1] Either Edge Triggered Interrupt Input 1 Status. This
bit is set when an edge occurs on the GP22 pin.
Bit[2] Either Edge Triggered Interrupt Input 2 Status. This
bit is set when an edge occurs on the GP41 pin.
Bit[3] Either Edge Triggered Interrupt Input 3 Status. This
bit is set when an edge occurs on the GP43 pin.
Bit[4] Either Edge Triggered Interrupt Input 4 Status. This
bit is set when an edge occurs on the GP60 pin.
Bit[5] Either Edge Triggered Interrupt Input 5 Status. This
bit is set when an edge occurs on the GP61 pin.
Bit[7:6] Reserved. This bit always returns zero.
Reserved – reads return 0
N/A
1D
(R)
1E
Force Disk Change
Force Disk Change
Bit[0] Force Disk Change for FDC0
0=Inactive
Default = 0x01 on
VCC POR
(R/W)
1=Active
Bit[1] Force Disk Change for FDC1
0=Inactive
1=Active
Force Change 0 and 1 can be written to 1 but are not
clearable by software.
Force Change 0 is cleared on nSTEP and nDS0
Force Change 1 is cleared on nSTEP and nDS1
DSKCHG (FDC DIR Register, Bit 7) = (nDS0 AND Force
Change 0) OR (nDS1 AND Force Change 1) OR
nDSKCHG
Setting either of the Force Disk Change bits active ‘1’
forces the FDD nDSKCHG input active when the
appropriate drive has been selected.
Bit[7:2] Reserved
SMSC DS – LPC47M14X
Page 135
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
DESCRIPTION
Floppy Data Rate Select Shadow
Bit[0] Data Rate Select 0
Bit[1] Data Rate Select 1
Bit[2] PRECOMP 0
Floppy Data Rate
1F
Select Shadow
(R)
Bit[3] PRECOMP 1
Bit[4] PRECOMP 2
Bit[5] Reserved
Bit[6] Power Down
Bit[7] Soft Reset
UART1 FIFO
20
UART FIFO Control Shadow 1
Control Shadow
Bit[0] FIFO Enable
(R)
Bit[1] RCVR FIFO Reset
Bit[2] XMIT FIFO Reset
Bit[3] DMA Mode Select
Bit[5:4] Reserved
Bit[6] RCVR Trigger (LSB)
Bit[7] RCVR Trigger (MSB)
UART FIFO Control Shadow 2
Bit[0] FIFO Enable
Bit[1] RCVR FIFO Reset
Bit[2] XMIT FIFO Reset
Bit[3] DMA Mode Select
Bit[5:4] Reserved
UART2 FIFO Control
Shadow
21
(R)
Bit[6] RCVR Trigger (LSB)
Bit[7] RCVR Trigger (MSB)
SMSC DS – LPC47M14X
Page 136
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
DESCRIPTION
Device Disable
22
If “0” (enabled), bits[7:3] have no effect on the devices;
devices are controlled by their respective activate bits. If
“1” (disabled), bits[7:3] override the activate bits in the
configuration registers for each logical block.
Register
Read/Write when
GP43 register
bits[3:2] = 01
AND
GP43 pin = 0
OR
Default = 0x00
VTR POR
Bit[0]: Floppy Write Protect.
0= no effect: floppy write protection is controlled by the
write protect pin or the forced write protect bit (bit 0 of
register 0xF1 in Logical Device 0);
1= Write Protected.
GP43 register
bits[3:2] ≠ 01
If set to 1, this bit overrides the write protect pin on the
part and the forced write protect bit.
nWRTPRT (to the FDC Core) = (nDS0 AND Force Write
Protect) OR (nDS1 AND Force Write Protect)OR
nWRTPRT (from the FDD Interface) OR Floppy Write
Protect
READ-ONLY
When GP43
register bits[3:2]
=01 AND GP43
pin = 1
Note: The Force Write Protect bit is in the FDD Option
configuration register.
Bits[2:1]: Reserved. Return 0 on read.
Bit[3]: Floppy Enable.
0=No effect: FDC controlled by its activate bit;
1=Floppy Disabled
Bit[4]: MPU-401 Serial Port Enable.
0=No effect: MPU-401 UART controlled by its activate
bit;
1=MPU-401 UART Disabled
Bit[5]: Serial Port 2 Enable.
0=No effect: UART2 controlled by its activate bit;
1=UART2 Disabled
Bit[6]: Serial Port 1 Enable.
0=No effect: UART1 controlled by its activate bit;
1=UART1 Disabled
Bit[7]: Parallel Port Enable.
0=No effect: PP controlled by its activate bit;
1=PP Disabled
GP10
23
General Purpose I/0 bit 1.0
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1=J1B1 (Joystick 1, Button 1)
0=GPIO
Default = 0x01
on VTR POR
(R/W)
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
SMSC DS – LPC47M14X
Page 137
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
DESCRIPTION
General Purpose I/0 bit 1.1
GP11
Default = 0x01
on VTR POR
24
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1= J1B2 (Joystick 1, Button 2)
0=GPIO
(R/W)
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP12
25
General Purpose I/0 bit 1.2
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity :=1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1= J2B1 (Joystick 2, Button 1)
0=GPIO
Default = 0x01
on VTR POR
(R/W)
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP13
26
General Purpose I/0 bit 1.3
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1= J2B2 (Joystick 2, Button 2)
0=GPIO
Default = 0x01
on VTR POR
(R/W)
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP14
27
General Purpose I/0 bit 1.4
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1= J1X (Joystick 1, X-Axis RC Constant)
0=GPIO
Default = 0x01
on VTR POR
(R/W)
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP15
28
General Purpose I/0 bit 1.5
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1= J1Y (Joystick 1, Y-Axis RC Constant)
0=GPIO
Default = 0x01
on VTR POR
(R/W)
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
SMSC DS – LPC47M14X
Page 138
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
DESCRIPTION
General Purpose I/0 bit 1.6
GP16
29
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1= J2X (Joystick 2, X-Axis RC Constant)
0=GPIO
Default = 0x01
on VTR POR
(R/W)
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP17
2A
General Purpose I/0 bit 1.7
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1= J2Y (Joystick 2, Y-Axis RC Constant)
0=GPIO
Default = 0x01
on VTR POR
(R/W)
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP20
2B
General Purpose I/0 bit 2.0
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1=8042 P17 function (Note 10)
0=Basic GPIO function
Default = 0x01
on VTR POR
(R/W)
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP21
2C
General Purpose I/0 bit 2.1
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[3:2] Alternate Function Select
11= nDS1 – Floppy Drive Select 1 (Note 4)
10=Either Edge Triggered Interrupt Input 0 (Note 1)
01=8042 P16 function (Note 10)
00=Basic GPIO function
Bits[6:4] Reserved
Default =0x01
on VTR POR
(R/W)
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
SMSC DS – LPC47M14X
Page 139
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
DESCRIPTION
General Purpose I/0 bit 2.2
GP22
2D
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[3:2] Alternate Function Select
11= nMTR1 – Floppy Motor Select 1 (Note 4)
10=Either Edge Triggered Interrupt Input 1 (Note 1)
01=8042 P12 function (Note 10)
00=Basic GPIO function
Default =0x01
on VTR POR
(R/W)
Bits[6:4] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
N/A
2E
(R)
2F
Reserved – reads return 0
GP24
General Purpose I/0 bit 2.4
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Reserved
Default = 0x01
on VTR POR
(R/W)
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP25
30
(R/W)
General Purpose I/0 bit 2.5
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1=MIDI_IN
0=GPIO
Bits[6:3] Reserved
Default = 0x01
on VTR POR
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP26
31
General Purpose I/0 bit 2.6
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1=MIDI_OUT
0=GPIO
Bits[6:3] Reserved
Default = 0x01
on VTR POR
(R/W)
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP27
32
General Purpose I/0 bit 2.7
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1=nIO_SMI (Note 5)
0=GPIO
Default = 0x01
on VTR POR
(R/W)
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
SMSC DS – LPC47M14X
Page 140
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
DESCRIPTION
General Purpose I/0 bit 3.0
GP30
33
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity :=1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1=FAN_TACH2
Default = 0x01
on VTR POR
(R/W)
0=GPIO
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP31
34
General Purpose I/0 bit 3.1
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1=FAN_TACH1
Default = 0x01
on VTR POR
(R/W)
0=GPIO
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP32
35
General Purpose I/0 bit 3.2
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1=FAN2
0=GPIO
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
Default = 0x01
on VTR POR
Default = 0x00
on VCC POR
and Hard Reset
(Note 3)
(R/W)
GP33
36
General Purpose I/0 bit 3.3
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1=FAN1
Default = 0x01
on VTR POR
Default = 0x00
on VCC POR
and Hard Reset
(Note 3)
(R/W)
0=GPIO
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP34
37
General Purpose I/0 bit 3.4
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1=IRRX2
Default = 0x05
on VTR POR
(R/W)
0=GPIO
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
SMSC DS – LPC47M14X
Page 141
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
DESCRIPTION
General Purpose I/0 bit 3.5
GP35
38
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1=IRTX2 (Note 2)
Default = 0x04
(R/W)
on VTR POR, VCC
POR and Hard
Reset
0=GPIO
Bits[6:3] Reserved
(Note 3)
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP36
39
General Purpose I/0 bit 3.6
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1= nKBDRST
Default = 0x01
on VTR POR
(R/W)
0=Basic GPIO function
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP37
3A
General Purpose I/0 bit 3.7
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1=A20M
Default = 0x01
on VTR POR
(R/W)
0=Basic GPIO function
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP40
3B
General Purpose I/0 bit 4.0
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1=DRVDEN0 (Note 4)
0=Basic GPIO function
Bits[6:3] Reserved
Default =0x01
on VTR POR
(R/W)
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP41
3C
General Purpose I/0 bit 4.1
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[3:2] Alternate Function Select
11=Reserved
Default =0x01
on VTR POR
(R/W)
10=Either Edge Triggered Interrupt Input 2 (Note 1)
01=DRVDEN1 (Note 4)
00=Basic GPIO function
Bits[6:4] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
SMSC DS – LPC47M14X
Page 142
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
DESCRIPTION
General Purpose I/0 bit 4.2
GP42
3D
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[2] Alternate Function Select
1=nIO_PME
Default =0x01
on VTR POR
(R/W)
Note: configuring this pin function as output with non-
inverted polarity will give an active low output signal. The
output type can be either open drain or push-pull.
0=Basic GPIO function
Bits[6:3] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP43
3E
General Purpose I/0 bit 4.3
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[3:2] Alternate Function Select
11=Either Edge Triggered Interrupt Input 3 (Note 1)
Default = 0x01
on VTR POR
Bits[3:2] are reset
(cleared) on VCC
POR, VTR POR and
Hard Reset
(R/W)
10=Reserved01=Device Disable Register Control. The
GP43 pin is an input, with non-inverted polarity. When
bits[3:2]=01, they cannot be changed by writing to these
bits; they are cleared by VCC POR, Hard Reset and VTR
POR. That is, when the DDRC function is selected for this
pin, it cannot be changed, except by a VCC POR, Hard
Reset or VTR POR.
The Device Disable register is controlled by the value of
the GP43 pin as follows:
If the GP43 pin is high, the Device Disable Register is
Read-Only.
If the GP43 pin is low, the Device Disable Register is
Read/Write.
00=Basic GPIO function
Bits[6:4] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP50
3F
General Purpose I/0 bit 5.0
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[3:2] Alternate Function Select
11=Reserved
Default = 0x01
on VTR POR
(R/W)
10=Reserved
01=nRI2 (Note 9)
00=GPIO
Bits[6:4] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
SMSC DS – LPC47M14X
Page 143
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
DESCRIPTION
General Purpose I/0 bit 5.1
GP51
40
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[3:2] Alternate Function Select
11=Reserved
Default = 0x01
on VTR POR
(R/W)
10=Reserved
01=nDCD2
00=GPIO
Bits[6:4] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP52
41
General Purpose I/0 bit 5.2
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[3:2] Alternate Function Select
11=Reserved
Default = 0x01
on VTR POR
(R/W)
10=Reserved
01=RXD2
00=GPIO
Bits[6:4] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP53
42
General Purpose I/0 bit 5.3
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[3:2] Alternate Function Select
11=Reserved
Default = 0x00
(R/W)
on VTR POR, VCC
POR and Hard
Reset
10=Reserved
(Note 3)
01=TXD2
00=GPIO
Bits[6:4] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP54
43
General Purpose I/0 bit 5.4
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[3:2] Alternate Function Select
11=Reserved
Default = 0x01
on VTR POR
(R/W)
10=Reserved
01=nDSR2
00=GPIO
Bits[6:4] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
SMSC DS – LPC47M14X
Page 144
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
DESCRIPTION
General Purpose I/0 bit 5.5
GP55
44
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[3:2] Alternate Function Select
11=Reserved
Default = 0x01
on VTR POR
(R/W)
10=Reserved
01=nRTS2
00=GPIO
Bits[6:4] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP56
45
General Purpose I/0 bit 5.6
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[3:2] Alternate Function Select
11=Reserved
Default = 0x01
on VTR POR
(R/W)
10=Reserved
01=nCTS2
00=GPIO
Bits[6:4] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP57
46
General Purpose I/0 bit 5.7
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[3:2] Alternate Function Select
11=Reserved
Default = 0x01
on VTR POR
(R/W)
10=Reserved
01=nDTR2
00=GPIO
Bits[6:4] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
GP60
47
General Purpose I/0 bit 6.0
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[3:2] Alternate Function Select
11=Reserved
Default = 0x01
on VTR POR
(R/W)
10=Either Edge Triggered Interrupt Input 4 (Note 1)
01=LED1
00=GPIO
Bits[6:4] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
SMSC DS – LPC47M14X
Page 145
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
DESCRIPTION
General Purpose I/0 bit 6.1
GP61
48
Bit[0] In/Out : =1 Input, =0 Output
Bit[1] Polarity : =1 Invert, =0 No Invert
Bit[3:2] Alternate Function Select
11=Reserved
Default = 0x01
on VTR POR
(R/W)
10=Either Edge Triggered Interrupt Input 5 (Note 1)
01=LED2
00=GPIO
Bits[6:4] Reserved
Bit[7] Output Type Select
1=Open Drain
0=Push Pull
Reserved – reads return 0
N/A
N/A
GP1
49
(R)
4A
(R)
4B
Reserved – reads return 0
General Purpose I/0 Data Register 1
Bit[0] GP10
Default = 0x00
on VTR POR
(R/W)
Bit[1] GP11
Bit[2] GP12
Bit[3] GP13
Bit[4] GP14
Bit[5] GP15
Bit[6] GP16
Bit[7] GP17
GP2
Default = 0x00
on VTR POR
4C
General Purpose I/0 Data Register 2
Bit[0] GP20
(R/W)
Bit[1] GP21
Bit[2] GP22
Bit[3] Reserved
Bit[4] GP24
Bit[5] GP25
Bit[6] GP26
Bit[7] GP27
GP3
4D
General Purpose I/0 Data Register 3
Bit[0] GP30
Default = 0x00
on VTR POR
(R/W)
Bit[1] GP31
Bit[2] GP32
Bits
2
and
3
are
Bit[3] GP33
reset on VCC POR,
Hard Reset and VTR
POR
Bit[4] GP34
Bit[5] GP35
Bit[6] GP36
Bit[7] GP37
GP4
4E
General Purpose I/0 Data Register 4
Bit[0] GP40
Default = 0x00
on VTR POR
(R/W)
Bit[1] GP41
Bit[2] GP42
Bit[3] GP43
Bit[7:4] Reserved
SMSC DS – LPC47M14X
Page 146
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
DESCRIPTION
General Purpose I/0 Data Register 5
Bit[0] GP50
GP5
4F
Default = 0x00
on VTR POR
Bit 3 is reset on VCC
POR, Hard Reset
and VTR POR
(R/W)
Bit[1] GP51
Bit[2] GP52
Bit[3] GP53
Bit[4] GP54
Bit[5] GP55
Bit[6] GP56
Bit[7] GP57
GP6
50
General Purpose I/0 Data Register 6
Bit[0] GP60
Default = 0x00
on VTR POR
N/A
(R/W)
Bit[1] GP61
Bit[7:2] Reserved
Reserved – reads return 0
51
(R)
52
N/A
Reserved – reads return 0
(R)
53
N/A
Reserved – reads return 0
(R)
54
INT_GEN1
Default = 0xFF
Interrupt Generating Register 1 (Note 8)
0=Corresponding Interrupt frame driven low in the SER
IRQ stream. This must be enabled through the INT_G
Configuration Register.
(R/W)
on VCC POR and
Bit[0] Reserved
Bit[1] nINT1
Bit[2] nINT2
Bit[3] nINT3
Bit[4] nINT4
Bit[5] nINT5
Bit[6] nINT6
Bit[7] nINT7
HARD RESET
Note: To enable/disable this register see Logical
Device A (0xF1)
Interrupt Generating Register 2 (Note 8)
INT_GEN2
55
0=Corresponding Interrupt frame driven low in the SER
IRQ stream. This must be enabled through the INT_G
Configuration Register.
Default = 0xFF
(R/W)
on VCC POR and
Bit[0] nINT8
Bit[1] nINT9
Bit[2] nINT10
Bit[3] nINT11
Bit[4] nINT12
Bit[5] nINT13
Bit[6] nINT14
Bit[7] nINT15
HARD RESET
Note: To enable/disable this register see Logical
Device A (0xF1)
SMSC DS – LPC47M14X
Page 147
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
DESCRIPTION
FAN1
56
FAN Register 1
Bit[0] Fan Control
Default = 0x00
on VTR POR
(R/W)
1=FAN1 pin is high
0=bits[6:1] control the duty cycle of the
FAN1 pin.
Bit[6:1] Duty Cycle Control for FAN1
Control the duty cycle of the FAN1 pin
000000 = pin is low
100000 = 50% duty cycle
111111 = pin is high for 63, low for 1
Bit[7] Fan 1 Clock Select
This bit is used with the Fan 1 Clock Source Select and
the Fan 1 Clock Multiplier bits in the Fan Control register
(0x58) to determine the fan speed FOUT
.
See Table 57
–
Different Modes for Fan in “Fan Speed Control and
Monitoring” section.
The fan speed may be doubled through bit 2 of Fan
Control Register at 0x58.
FAN Register 2
FAN2
57
Bit[0] Fan Control
1=FAN2 pin is high
Default = 0x00
on VTR POR
(R/W)
0=bits[6:1] control the duty cycle of the
FAN2 pin.
Bit[6:1] Duty Cycle Control for FAN2
Control the duty cycle of the FAN2 pin
000000 = pin is low
100000 = 50% duty cycle
111111 = pin is high for 63, low for 1
Bit[7] Fan 2 Clock Select
This bit is used with the Fan 2 Clock Source Select and
the Fan 2 Clock Multiplier bits in the Fan Control register
(0x58) to determine the fan speed FOUT
.
See Table 57
–
Different Modes for Fan in “Fan Speed Control and
Monitoring” section.
The fan speed may be doubled through bit 3 of Fan
Control Register at 0x58.
SMSC DS – LPC47M14X
Page 148
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
Fan Control
DESCRIPTION
58
Fan Control Register
Bit[0] Fan 1 Clock Source Select
Default = 0x50
on VTR POR
(R/W)
This bit and the Fan 1 Clock Multiplier bit is used with
The Fan 1 Clock Select bit in the Fan 1 register (0x56) to
determine the fan speed FOUT
.
See Table 57
–
Different Modes for Fan in “Fan Speed Control and
Monitoring” section.
Bit[1] Fan 2 Clock Source Select
This bit and the Fan 2 Clock Multiplier bit is used with
The Fan 2 Clock Select bit in the Fan 2 register (0x57) to
determine the fan speed FOUT
.
See Table 57
–
Different Modes for Fan in “Fan Speed Control and
Monitoring” section.
Bit[2] Fan 1 Clock multiplier
0=No multiplier used
1=Double the fan speed selected by bit 0 of this
register and bit 7 of the FAN1
register
Bit[3] Fan 2 Clock multiplier
0=No multiplier used
1=Double the fan speed selected by bit 1 of this
register and bit 7 of the FAN2 register
Bit[5:4] The FAN1 count divisor. Clock scalar for
adjusting the tachometer count. Default = 2.
00: divisor = 1
01: divisor = 2
10: divisor = 4
11: divisor = 8
Bit[7:6] The FAN2 count divisor. Clock scalar for
adjusting the tachometer count. Default = 2.
00: divisor = 1
01: divisor = 2
10: divisor = 4
11: divisor = 8
Fan Tachometer Register 1
Fan1 Tachometer
Register
59
Bit]7:0] The 8-bit FAN1 tachometer count. The number
of counts of the internal clock per pulse of the fan. The
count value is computed from Equation 1. This value is
the final (maximum) count of the previous pulse
(latched). The value in this register may not be valid for
up to 2 pulses following a write to the preload register.
(R)
Default = 0x00
on VTR POR
Fan2 Tachometer
Register
5A
Fan Tachometer Register 2
Bit[7:0] The 8-bit FAN2 tachometer count. The number
of counts of the internal clock per pulse of the fan. The
count value is computed from Equation 1. This value is
the final (maximum) count of the previous pulse
(latched). The value in this register may not be valid for
up to 2 pulses following a write to the preload register.
(R)
Default = 0x00
on VTR POR
Fan1 Preload
Register
5B
Fan Preload Register 1
Bit[7:0] The FAN1 tachometer preload. This is the initial
value used in the computation of the FAN1 count.
Writing this register resets the tachometer count.
(R/W)
Default = 0x00
on VTR POR
SMSC DS – LPC47M14X
Page 149
Rev. 03/19/2001
REG OFFSET
(hex)
NAME
DESCRIPTION
Fan Preload Register 2
Bit[7:0] The FAN2 tachometer preload. This is the initial
value used in the computation of the FAN2 count.
Writing this register resets the tachometer count.
Fan2 Preload
5C
Register
(R/W)
Default = 0x00
on VTR POR
LED1
5D
LED1
Bit[1:0] LED1 Control
00=off
Default = 0x00
on VTR POR
(R/W)
01=blink at 1Hz rate with a 50% duty cycle (0.5 sec on,
0.5 sec off)
10=Blink at ½ HZ rate with a 25% duty cycle (0.5 sec on,
1.5 sec off)
11=on
Bits[7:2] Reserved
LED2
LED2
5E
Bit[1:0] LED2 Control
00=off
Default = 0x00
on VTR POR
(R/W)
01=blink at 1Hz rate with a 50% duty cycle (0.5 sec on,
0.5 sec off)
10=Blink at ½ HZ rate with a 25% duty cycle (0.5 sec on,
1.5 sec off)
11=on
Bits[7:2] Reserved
Keyboard Scan Code
Bit[0] LSB of Scan Code
. . .
Keyboard Scan
Code
5F
(R/W)
Default = 0x00
on VTR POR
. . .
. . .
Bit[7] MSB of Scan Code
Reserved – reads return 0
N/A
60-7F
(R)
Note 1: If the EETI function is selected for this GPIO then both a high-to-low and a low-to-high edge will set the PME,
SMI and MSC status bits.
Note 2: The IRTX2 function can be used on this pin if the IR Location Mux bit in the Serial Port 2 IR Option register is
set.
Note 3: These pins default to an output and LOW on VCC POR and Hard Reset.
Note 4: If the FDC function is selected on this pin (nMTR1, nDS1, DRVDEN0, DRVDEN1) then bit 6 of the FDD
Mode Register (Configuration Register 0xF0 in Logical Device 0) will override bit 7 in the GPIO Control Register. Bit
7 of the FDD Mode Register will also affect the pin if the FDC function is selected.
Note 5: The nIO_SMI pin is inactive when the internal group SMI signal is inactive and when the SMI enable bit
(EN_SMI, bit 7 of the SMI_EN2 register) is ‘0’. When the output buffer type is OD, nIO_SMI pin is floating when
inactive; when the output buffer type is push-pull, the nIO_SMI pin is high when inactive.
Note 6: Bits 2 and 3 of the PME_STS4 and SMI_STS4 registers, and bit 3 of the PME_STS5 register may be set on
a VCC POR. If GP32, GP33 and GP53 are configured as input, then their corresponding PME and SMI status bits
will be set on a VCC POR. Also, GP32 and GP33 pins revert to their non-inverting GPIO input function when VCC is
removed from the part. These GPIOs cannot be used for PME wakeup when the part is under VTR power (VCC=0).
Note 7: These bits are R/W but have no effect on circuit operation.
Note 8: These bits when read indicate the current bit status. These bits are set to “0” by writing “0” to individual bit
locations in this register. Producing an interrupt in the SER IRQ stream by setting these bits to “0” overrides other
interrupt sources for the SER IRQ stream. No other functional logic in the LPC47M14X sets bits in this register.
These bits are only cleared by writing a ‘1’ to the bit location.
SMSC DS – LPC47M14X
Page 150
Rev. 03/19/2001
Note 9: If this pin is used for Ring Indicator wakeup, either the nRI2 event can be enabled via bit 1 in the PME_EN1
register or the GP50 PME event can be enabled via bit 0 in the PME_EN5 register.
Note 10: In order to use the P12, P16 and P17 functions, the corresponding GPIO must be programmed for output,
non-invert, and push-pull output type.
The P17 function should not be selected on GP20 and GP 62 simultaneously. If P17 is selected on GP20 and GP62,
simultaneously, then P17 on GP62 will function and P17 on GP20 will not.
The following register is located at an offset of zero from (GAME_PORT) the address into the base I/O address
register for Logical Device 9.
Table 60 – Game Port
NAME
REG OFFSET
(hex)
DESCRIPTION
Game Port Register
00
Game Port Register
Bit[0]
Bit[1]
Bit[2]
Bit[3]
Bit[4]
Bit[5]
Bit[6]
Bit[7]
X-Axis Joystick 1 (OUT1A)
Y-Axis Joystick 1 (OUT1B)
X-Axis Joystick 2 (OUT2A)
Y-axis Joystick 2 (OUT2B)
Button Joystick 1 (J1B1)
Button Joystick 1 (J1B2)
Button Joystick 2 (J2B1)
Button Joystick 2 (J2B2)
Default = 0x00
on VTR POR
(R)
SMSC DS – LPC47M14X
Page 151
Rev. 03/19/2001
8
CONFIGURATION
The Configuration of the LPC47M14x is very flexible and is based on the configuration architecture implemented in
typical Plug-and-Play components. The LPC47M14x is designed for motherboard applications in which the resources
required by their components are known. With its flexible resource allocation architecture, the LPC47M14x allows the
BIOS to assign resources at POST.
SYSTEM ELEMENTS
Primary Configuration Address Decoder
After a hard reset (PCI_RESET# pin asserted) or Vcc Power On Reset the LPC47M14x is in the Run Mode with all
logical devices disabled. The logical devices may be configured through two standard Configuration I/O Ports (INDEX
and DATA) by placing the LPC47M14x into Configuration Mode.
The BIOS uses these configuration ports to initialize the logical devices at POST. The INDEX and DATA ports are only
valid when the LPC47M14x is in Configuration Mode.
The SYSOPT pin is latched on the falling edge of the PCI_RESET# or on Vcc Power On Reset to determine the
configuration register's base address. The SYSOPT pin is used to select the CONFIG PORT's I/O address at power-up.
Once powered up the configuration port base address can be changed through configuration registers CR26 and CR27.
The SYSOPT pin is a hardware configuration pin which is shared with the GP24 signal on pin 45.
Note: An external pull-down resistor is required for the base IO address to be 0x02E for configuration. An
external pull-up resistor is required to move the base IO address for configuration to 0x04E.
The INDEX and DATA ports are effective only when the chip is in the Configuration State.
SYSOPT= 0
10k PULL-DOWN
RESISTOR
SYSOPT= 1
10K PULL-UP
RESISTOR
PORT NAME
TYPE
CONFIG PORT (Note)
0x02E
0x02E
0x04E
0x04E
Write
INDEX PORT (Note)
DATA PORT
Read/Write
Read/Write
INDEX PORT + 1
Note : The configuration port base address can be relocated through CR26 and CR27.
Entering the Configuration State
The device enters the Configuration State when the following Config Key is successfully written to the CONFIG PORT.
Config Key = <0x55>
Exiting the Configuration State
The device exits the Configuration State when the following Config Key is successfully written to the CONFIG PORT.
Config Key = <0xAA>
SMSC DS – LPC47M14X
Page 152
Rev. 03/19/2001
CONFIGURATION SEQUENCE
To program the configuration registers, the following sequence must be followed:
1) Enter Configuration Mode
2) Configure the Configuration Registers
3) Exit Configuration Mode.
Enter Configuration Mode
To place the chip into the Configuration State the Config Key is sent to the chip's CONFIG PORT. The config key
consists of 0x55 written to the CONFIG PORT. Once the configuration key is received correctly the chip enters into the
Configuration State (The auto Config ports are enabled).
Configuration Mode
The system sets the logical device information and activates desired logical devices through the INDEX and DATA ports.
In configuration mode, the INDEX PORT is located at the CONFIG PORT address and the DATA PORT is at INDEX
PORT address + 1.
The desired configuration registers are accessed in two steps:
a) Write the index of the Logical Device Number Configuration Register (i.e., 0x07) to the INDEX PORT and then write
the number of the desired logical device to the DATA PORT
b) Write the address of the desired configuration register within the logical device to the INDEX PORT and then write or
read the configuration register through the DATA PORT.
Note: If accessing the Global Configuration Registers, step (a) is not required.
Exit Configuration Mode
To exit the Configuration State the system writes 0xAA to the CONFIG PORT. The chip returns to the RUN State.
Note: Only two states are defined (Run and Configuration). In the Run State the chip will always be ready to enter the
Configuration State.
Programming Example
The following is an example of a configuration program in Intel 8086 assembly language.
;----------------------------.
; ENTER CONFIGURATION MODE |
;----------------------------'
MOV
MOV
OUT
DX,02EH
AX,055H
DX,AL
;----------------------------.
; CONFIGURE REGISTER CRE0, |
; LOGICAL DEVICE 8
;----------------------------'
|
MOV
MOV
OUT
MOV
MOV
OUT
;
DX,02EH
AL,07H
DX,AL ;Point to LD# Config Reg
DX,02FH
AL, 08H
DX,AL;Point to Logical Device 8
MOV
MOV
OUT
MOV
MOV
OUT
DX,02EH
AL,E0H
DX,AL ; Point to CRE0
DX,02fH
AL,02H
DX,AL ; Update CRE0
;-----------------------------.
; EXIT CONFIGURATION MODE
;-----------------------------'
|
MOV
MOV
OUT
DX,02EH
AX,0AAH
DX,AL
SMSC DS – LPC47M14X
Page 153
Rev. 03/19/2001
Notes: HARD RESET: PCI_RESET# pin asserted
SOFT RESET: Bit 0 of Configuration Control register set to one
All host accesses are blocked for 500µs after Vcc POR (see Power-up Timing Diagram)
Table 61 – LPC47M14x Configuration Registers Summary
INDEX
TYPE
HARD
VCC POR
VTR POR
SOFT
CONFIGURATION REGISTER
RESET
RESET
GLOBAL CONFIGURATION REGISTERS
0x02
0x03
0x07
0x20
0x21
0x22
W
R
R/W
R
R
0x00
-
0x00
-
0x00
-
-
Config Control
-
0x00
0x5F
0x00
0x00
(Note 1)
-
Reserved – reads return 0
Logical Device Number
Device ID - hard wired
Device Rev - hard wired
Power Control
0x00
0x5F
0x00
0x00
(Note 1)
0x00
0x44
0x00
0x5F
0x00
0x00
(Note 1)
0x00
0x44
0x00
0x5F
0x00
0x00
(Note 1)
0x00
0x44
-
R/W
0x23
0x24
0x26
R/W
R/W
R/W
Power Mgmt
OSC
Configuration Port Address Byte 0
(Low Byte)
-
-
Sysopt=0:
Sysopt=0:
0x2E
0x2E
Sysopt=1:
0x4E
Sysopt=1:
0x4E
0x27
R/W
Sysopt=0:
Sysopt=0:
-
-
Configuration Port Address Byte 1
(High Byte)
0x00
0x00
Sysopt=1:
0x00
Sysopt=1:
0x00
0x28
0x2A
0x2B
0x2C
0x2D
0x2E
0x2F
R
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Reserved
TEST 6
TEST 4
TEST 5
TEST 1
TEST 2
TEST 3
R/W
R/W
R/W
R/W
R/W
R/W
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
LOGICAL DEVICE 0 CONFIGURATION REGISTERS (FDD)
0x30
0x60,
0x61
0x70
0x74
0xF0
0xF1
0xF2
0xF4
0xF5
R/W
R/W
0x00
0x03,
0xF0
0x06
0x02
0x0E
0x00
0xFF
0x00
0x00
0x00
0x03,
0xF0
0x06
0x02
0x0E
0x00
0xFF
0x00
0x00
0x00
0x03,
0xF0
0x06
0x02
0x0E
0x00
0xFF
0x00
0x00
0x00
0x03,
0xF0
0x06
0x02
-
-
-
-
-
Activate
Primary Base I/O Address
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Primary Interrupt Select
DMA Channel Select
FDD Mode Register
FDD Option Register
FDD Type Register
FDD0
FDD1
LOGICAL DEVICE 1 CONFIGURATION REGISTERS (Reserved)
LOGICAL DEVICE 2 CONFIGURATION REGISTERS (Reserved)
LOGICAL DEVICE 3 CONFIGURATION REGISTERS (Parallel Port)
0x30
0x60,
0x61
0x70
0x74
0xF0
0xF1
R/W
R/W
0x00
0x00,
0x00
0x00
0x04
0x3C
0x00
0x00
0x00,
0x00
0x00
0x04
0x3C
0x00
0x00
0x00,
0x00
0x00
0x04
0x3C
0x00
0x00
0x00,
0x00
0x00
0x04
-
Activate
Primary Base I/O Address
R/W
R/W
R/W
R/W
Primary Interrupt Select
DMA Channel Select
Parallel Port Mode Register
-
Parallel Port Mode Register 2
SMSC DS – LPC47M14X
Page 154
Rev. 03/19/2001
INDEX
TYPE
HARD
VCC POR
VTR POR
SOFT
CONFIGURATION REGISTER
RESET
RESET
LOGICAL DEVICE 4 CONFIGURATION REGISTERS (Serial Port 1)
0x30
0x60,
0x61
0x70
0xF0
R/W
R/W
0x00
0x00,
0x00
0x00
0x00
0x00
0x00,
0x00
0x00
0x00
0x00
0x00,
0x00
0x00
0x00
0x00
0x00,
0x00
0x00
-
Activate
Primary Base I/O Address
R/W
R/W
Primary Interrupt Select
Serial Port 1 Mode Register
LOGICAL DEVICE 5 CONFIGURATION REGISTERS (Serial Port 2)
0x30
0x60,
0x61
0x62,
0x63
0x70
0x74
0xF0
0xF1
0xF2
R/W
R/W
-
-
0x00
0x00,
0x00
-
-
Activate
Primary Base I/O Address
0x00,
0x00
-
0x00,
0x00
-
0x00,
0x00
-
R
Reserved – reads return 0
R/W
R
R/W
R/W
R/W
0x00
-
0x00
0x02
0x03
0x00
-
0x00
0x02
0x03
0x00
-
0x00
0x02
0x03
0x00
Primary Interrupt Select
Reserved – reads return 0
Serial Port 2 Mode Register
IR Options Register
-
-
-
-
IR Half Duplex Timeout
LOGICAL DEVICE 6 CONFIGURATION REGISTERS (Reserved)
0x30
0x70
0x72
0xF0
R/W
R/W
R/W
R/W
LOGICAL DEVICE 8 CONFIGURATION REGISTERS (Reserved)
0x30
0x60,
0x61
R/W
R/W
LOGICAL DEVICE A CONFIGURATION REGISTERS (PME)
0x30
R/W
R/W
0x00
0x00,
0x00
-
0x00
0x00,
0x00
-
0x00
0x00,
0x00
0X00
0x00
0x00
0x00,
0x00
-
Activate
Primary Base I/O Address
0x60,
0x61
0XF0
0xF1
R/W
R/W
CLOCKI32
INT_G Register
0x00
0x00
0x00
0x30
0x60,
R/W
R/W
0x61
R/W
0x30
0x30
0x30
0x30
MPU-401 Primary Base I/O
Address Low Byte
0x70
0xF0
R/W
-
0x05
-
0x05
-
0x05
-
0x05
-
Primary Interrupt Select
Reserved
SMSC DS – LPC47M14X
Page 155
Rev. 03/19/2001
LOGICAL DEVICE C CONFIGURATION REGISTERS (USB Hub)
0x30
R/W
0x00
0x00
0x00
0x00
Activate (see Table 75)
(Note 2)
0xF0
0xF1
0xF2
0xF3
0xF4
0xF5
0xF6
0xF7
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0x00
0x24
0x04
0x40
0x01
0x00
0x00
0x00
-
-
-
-
-
-
-
-
OSC_CLK (Note 2)
IdVendor_Low (Notes 1 & 2 )
IdVendor_High (Notes 1 & 2 )
IdProduct_Low (Notes 1 & 2 )
IdProduct_High (Notes 1 & 2 )
BcdDevice_Low (Notes 1 & 2 )
BcdDevice_High (Notes 1 & 2 )
HubControl_1
(Notes 1 & 2 )
Note 1: CR22 bit 5 is reset on VTR only.
Note 2: The registers for the USB Hub are powered by VTR.
Note: Reserved registers are read-only, reads return 0.
Chip Level (Global) Control/Configuration Registers[0x00-0x2F]
The chip-level (global) registers lie in the address range [0x00-0x2F]. The design MUST use all 8 bits of the
ADDRESS Port for register selection. All unimplemented registers and bits ignore writes and return zero when read.
The INDEX PORT is used to select a configuration register in the chip. The DATA PORT is then used to access the
selected register. These registers are accessible only in the Configuration Mode.
Table 62 – Chip Level Registers
REGISTER
ADDRESS
DESCRIPTION
Chip (Global) Control Registers
STATE
0x00 -
0x01
0x02 W
Reserved - Writes are ignored, reads return 0.
Config Control
The hardware automatically clears this bit after the
write, there is no need for software to clear the bits.
C
Bit 0 = 1: Soft Reset. Refer to the "Configuration
Registers" table for the soft reset value for each
register.
Default = 0x00
on VCC POR,
VTR POR and
HARD RESET
0x03 - 0x06 Reserved - Writes are ignored, reads return 0.
Logical Device #
0x07 R/W A write to this register selects the current logical
device. This allows access to the control and
configuration registers for each logical device. Note:
The Activate command operates only on the selected
logical device.
C
Default = 0x00
on VCC POR,
VTR POR,
SOFT RESET and
HARD RESET
Card Level Reserved 0x08 - 0x1F Reserved - Writes are ignored, reads return 0.
SMSC DS – LPC47M14X
Page 156
Rev. 03/19/2001
REGISTER
ADDRESS
DESCRIPTION
Chip Level, SMSC Defined
STATE
Device ID -
Hard wired
0x20 R
A
read only register which provides device
C
identification. Bits[7:0] = 0x5F when read.
Default = 0x5F
on VCC POR,
VTR POR,
SOFT RESET and
HARD RESET
Device Rev
0x21 R
A read only register which provides device revision
information. Bits[7:0] = current revision when read.
C
C
Hard wired
= Current Revision
PowerControl
0x22 R/W Bit[0] FDC Power
Bit[1] Reserved
Default = 0x00
on VCC POR,
VTR POR,
Bit[2] Game Port Power
Bit[3] Parallel Port Power
Bit[4] Serial Port 1 Power
Bit[5] Serial Port 2 Power (Note 1)
Bit[6] Serial Port 3 Power
Bit[7] Reserved
SOFT RESET and
HARD RESET
0: Power Off or Disabled
1: Power On or Enabled
Power Mgmt
0x23 R/W Bit[0] FDC (see Note in the “FDC Power
C
Management” section.)
Bit[1] Reserved
Bit[2] Reserved
Default = 0x00
on VCC POR,
VTR POR and
HARD RESET
Bit[3] Parallel Port
Bit[4] Serial Port 1
Bit[5] Serial Port 2
Bit[6] Serial Port 3
Bit[7] Reserved (read as 0)
For each bit above (except Reserved)
= 0
= 1
Intelligent Pwr Mgmt off
Intelligent Pwr Mgmt on
OSC
0x24 R/W Bit[0] Reserved
C
Bit [1] PLL Control
Default = 0x44, on
VCC POR,
VTR POR and
HARD RESET
= 0
= 1
PLL is on (backward Compatible)
PLL is off
Bits[3:2] OSC
= 01
= 10
= 00
= 11
Osc is on, BRG clock is on.
Same as above (01) case.
Osc is on, BRG Clock Enabled.
Osc is off, BRG clock is disabled.
Bit [5:4] Reserved, set to zero
Bit [6] 16-Bit Address Qualification
= 0
= 1
12-Bit Address Qualification
16-Bit Address Qualification
Note: For normal operation, bit 6 should be set.
Bit[7] Reserved
SMSC DS – LPC47M14X
Page 157
Rev. 03/19/2001
REGISTER
Chip Level
Vendor Defined
ADDRESS
DESCRIPTION
Reserved - Writes are ignored, reads return 0.
STATE
0x25
Configuration
0x26
Bit[7:1] Configuration Address Bits [7:1]
C
Address Byte 0
Bit[0] = 0
See Note 2
Default
=0x2E (Sysopt=0)
=0x4E (Sysopt=1)
on VCC POR and
HARD RESET
Configuration
0x27
Bit[7:0] Configuration Address Bits [15:8]
See Note 2
C
Address Byte 1
Default = 0x00
on VCC POR and
HARD RESET
Default = 0x00
on VCC POR,
SOFT RESET and
HARD RESET
Chip Level
0x28
0x29
Bits[7:0] Reserved - Writes are ignored, reads return
0.
Reserved - Writes are ignored, reads return 0.
Vendor Defined
TEST 6
0x2A R/W Test Modes: Reserved for SMSC. Users should not
write to this register, may produce undesired results.
Default = 0x00, on
VCC POR and
VTR POR
TEST 4
0x2B R/W Test Modes: Reserved for SMSC. Users should not
write to this register, may produce undesired results.
C
C
Default = 0x00, on
VCC POR and
VTR POR
TEST 5
0x2C R/W Bit[7] Test Mode: Reserved for SMSC. Users
should not write to this bit, may produce undesired
results.
Default = 0x00, on
VCC POR and
VTR POR
Bit[6] 8042 Reset:
1 = put the 8042 into reset
0 = take the 8042 out of reset
Bits[5:0] Test Mode: Reserved for SMSC. Users
should not write to this bit, may produce undesired
results.
TEST 1
0x2D R/W Test Modes: Reserved for SMSC. Users should not
C
C
write to this register, may produce undesired results.
Default = 0x00, on
VCC POR and
VTR POR
TEST 2
0x2E R/W Test Modes: Reserved for SMSC. Users should not
write to this register, may produce undesired results.
Default = 0x00, on
VCC POR and
VTR POR
SMSC DS – LPC47M14X
Page 158
Rev. 03/19/2001
REGISTER
TEST 3
ADDRESS
DESCRIPTION
STATE
0x2F R/W Test Modes: Reserved for SMSC. Users should not
C
write to this register, may produce undesired results.
Default = 0x00, on
VCC POR and
VTR POR
Note 1: CR22 Bit 5 is reset by VTR POR only.
Note 2:
To allow the selection of the configuration address to a user defined location, these Configuration Address
Bytes are used. There is no restriction on the address chosen, except that A0 is 0, that is, the address must be on an
even byte boundary. As soon as both bytes are changed, the configuration space is moved to the specified location with
no delay (Note: Write byte 0, then byte 1; writing CR27 changes the base address).
The configuration address is only reset to its default address upon a Hard Reset or Vcc POR.
Note: The default configuration address is either 02E or 04E, as specified by the SYSOPT pin.
Logical Device Configuration/Control Registers [0x30-0xFF]
Used to access the registers that are assigned to each logical unit. This chip supports nine logical units and has nine
sets of logical device registers. The nine logical devices are Floppy, Parallel, Serial 1, Serial 2, Keyboard Controller,
game port, PME, MPU-401, and USB Hub. A separate set (bank) of control and configuration registers exists for each
logical device and is selected with the Logical Device # Register (0x07).
The INDEX PORT is used to select a specific logical device register. These registers are then accessed through the
DATA PORT.
The Logical Device registers are accessible only when the device is in the Configuration State. The logical register
addresses are shown in the table below.
Table 63 – Logical Device Registers
LOGICAL DEVICE
REGISTER
ADDRESS
DESCRIPTION
Bits[7:1] Reserved, set to zero.
Bit[0]
STATE
Activate (Note 1)
(0x30)
C
Default = 0x00
= 1
Activates the logical device currently
selected through the Logical Device #
register.
on VCC POR, VTR POR,
HARD RESET and
= 0
Logical device currently selected is
SOFT RESET
inactive
Logical Device Control
Logical Device Control
(0x31-0x37) Reserved – Writes are ignored, reads return 0.
C
C
(0x38-0x3F) Vendor Defined - Reserved - Writes are
ignored, reads return 0.
Memory Base Address
I/O Base Address (Note 2) (0x60-0x6F) Registers 0x60 and 0x61 set the base address
(0x40-0x5F) Reserved – Writes are ignored, reads return 0.
C
C
for the device. If more than one base address
is required, the second base address is set by
(see Device Base I/O
Address Table)
0x60,2,... =
addr[15:8]
registers 0x62 and 0x63.
Refer to Table 65 for the number of base
address registers used by each device.
Default = 0x00
0x61,3,... =
addr[7:0]
Unused registers will ignore writes and return
zero when read.
on VCC POR, VTR POR,
HARD RESET and
SOFT RESET
SMSC DS – LPC47M14X
Page 159
Rev. 03/19/2001
Table 64 – Logical Device Registers
ADDRESS DESCRIPTION
(0x70,0x72) 0x70 is implemented for each logical device.
Refer to Interrupt Configuration Register
description. Only the keyboard controller uses
Interrupt Select register 0x72. Unused register
(0x72) will ignore writes and return zero when
read. Interrupts default to edge high (ISA
compatible).
LOGICAL DEVICE
REGISTER
Interrupt Select
STATE
C
Defaults :
0x70 = 0x00 or 0x06
(Note 3)
on VCC POR, VTR POR,
HARD RESET and
SOFT RESET
0x72 = 0x00,
on VCC POR, VTR POR,
HARD RESET and
SOFT RESET
(0x71,0x73) Reserved - not implemented. These register
locations ignore writes and return zero when
read.
(0x74,0x75) Only 0x74 is implemented for FDC and Parallel
port. 0x75 is not implemented and ignores
writes and returns zero when read. Refer to
DMA Channel Configuration.
DMA Channel Select
C
Default = 0x02 or 0x04
(Note 4)
on VCC POR, VTR POR,
HARD RESET and
SOFT RESET
32-Bit Memory Space (0x76-0xA8) Reserved - not implemented. These register
Configuration
locations ignore writes and return zero when
read.
Logical Device
(0xA9-0xDF) Reserved - not implemented. These register
locations ignore writes and return zero when
read.
C
C
C
Logical
Device (0xE0-0xFE) Reserved
–
Vendor Defined (see SMSC
Configuration
defined
Logical Device Configuration
Registers).
Reserved
0xFF
Reserved
Note 1: A logical device will be active and powered up according to the following equation unless otherwise specified:
DEVICE ON (ACTIVE) = (Activate Bit SET or Pwr/Control Bit SET).
The Logical device's Activate Bit and its Pwr/Control Bit are linked such that setting or clearing one sets or
clears the other.
Note 2: If the I/O Base Addr of the logical device is not within the Base I/O range as shown in the Logical Device I/O
map, then read or write is not valid and is ignored.
Note 3: The default value of the Primary Interrupt Select register for logical device 0 is 0x06.
Note 4: The default value of the DMA Channel Select register for logical device 0 (FDD) is 0x02 and for logical device
3 and 5 is 0x04.
SMSC DS – LPC47M14X
Page 160
Rev. 03/19/2001
Table 65 – I/O Base Address Configuration Register Description
BASE I/O
LOGICAL
DEVICE
NUMBER
0x00
LOGICAL
DEVICE
FDC
REGISTER
RANGE
FIXED
INDEX
0x60,0x61
(NOTE 1)
[0x0100:0x0FF8]
BASE OFFSETS
+0 : SRA
+1 : SRB
ON 8 BYTE BOUNDARIES +2 : DOR
+3 : TSR
+4 : MSR/DSR
+5 : FIFO
+7 : DIR/CCR
n/a
n/a
0x01
0x02
0x03
Reserved
Reserved
Parallel
Port
n/a
n/a
0x60,0x61
n/a
n/a
[0x0100:0x0FFC]
+0 : Data/ecpAfifo
ON 4 BYTE BOUNDARIES +1 : Status
(EPP Not supported)
or
[0x0100:0x0FF8]
+2 : Control
+400h : cfifo/ecpDfifo/tfifo/cnfgA
+401h : cnfgB
ON 8 BYTE BOUNDARIES +402h : ecr
(all modes supported,
+3 : EPP Address
EPP is only available when +4 : EPP Data 0
the base address is on an 8-
byte boundary)
+5 : EPP Data 1
+6 : EPP Data 2
+7 : EPP Data 3
+0 : RB/TB/LSB div
+1 : IER/MSB div
0x04
0x05
Serial Port 1
Serial Port 2
0x60,0x61
0x60,0x61
[0x0100:0x0FF8]
ON 8 BYTE BOUNDARIES +2 : IIR/FCR
+3 : LCR
+4 : MSR
+5 : LSR
+6 : MSR
+7 : SCR
+0 : RB/TB/LSB div
+1 : IER/MSB div
[0x0100:0x0FF8]
ON 8 BYTE BOUNDARIES +2 : IIR/FCR
+3 : LCR
+4 : MSR
+5 : LSR
+6 : MSR
+7 : SCR
0x06
0x07
Reserved
KYBD
n/a
n/a
n/a
n/a
Not Relocatable
+0 : Data Register
Fixed Base Address: 60,64 +4 : Command/Status Reg.
0x08
0x09
Reserved
Game Port
n/a
0x60,0x61
n/a
n/a
[0x0100:0x0FFF]
on 1 byte boundaries
[0x0000:0x0F7F]
on 128-byte boundaries
+00: Game Port Register
0x0A
Runtime
Register
Block
0x60,0x61
+00 : PME Status
.
.
.
+5F : Keyboard Scan Code
(See Table in “Runtime Registers”
section for Full List)
SMSC DS – LPC47M14X
Page 161
Rev. 03/19/2001
Table 65 – I/O Base Address Configuration Register Description
BASE I/O
LOGICAL
DEVICE
NUMBER
0x0B
LOGICAL
REGISTER
RANGE
FIXED
INDEX
DEVICE
(NOTE 1)
BASE OFFSETS
MPU-401
0x60,0x61
[0x0100:0x0FFE]
on 2-byte boundaries
0x0100:0x0FFE
On 2 byte boundaries
+0: MIDI DATA
+1: STATUS/COMMAND
Config.
Port
Config. Port
USB Hub
0x26, 0x27
(Note 2)
See Configuration Register in Table
61. Accessed through the index and
DATA ports located at the
Configuration Port address and the
Configuration Port address +1
respectively.
0x0C
n/a
No Base I/O Address Range n/a
allocated to the Hub Block
Note 1: This chip uses address bits [A11:A0] to decode the base address of each of its logical devices. Bit 6 of the
OSC Global Configuration Register (CR24) must be set to ‘1’ and Address Bits [A15:A12] must be ‘0’ for 16 bit
address qualification.
Note 2: The Configuration Port is at either 0x02E or 0x04E (for SYSOPT=0 or SYSOPT=1) at power up and can be
replaced via the global configuration registers at 0x26 and 0x27.
Table 66 – Interrupt Select Configuration Register Description
NAME
REG INDEX
DEFINITION
STATE
Primary Interrupt 0x70 (R/W)
Select
Bits[3:0] selects which interrupt is used for the primary
C
Interrupt.
0x00= no interrupt selected
0x01= IRQ1
0x02= IRQ2/nSMI
0x03= IRQ3
Default=0x00 or
0x06 (Note 1)
on VCC POR,
VTR POR,
0x04= IRQ4
HARD RESET
and
0x05= IRQ5
0x06= IRQ6
SOFT RESET
0x07= IRQ7
0x08= IRQ8
0x09= IRQ9
0x0A= IRQ10
0x0B= IRQ11
0x0C= IRQ12
0x0D= IRQ13
0x0E= IRQ14
0x0F= IRQ15
Note: All interrupts are edge high (except ECP/EPP)
Note: nSMI is active low
Note:
An Interrupt is activated by setting the Interrupt Request Level Select 0 register to a non-zero value AND :
For the FDC logical device by setting DMAEN, bit D3 of the Digital Output Register.
For the PP logical device by setting IRQE, bit D4 of the Control Port and in addition
For the PP logical device in ECP mode by clearing serviceIntr, bit D2 of the ecr.
For the Serial Port logical device by setting any combination of bits D0-D3 in the IER
And by setting the OUT2 bit in the UART's Modem Control (MCR) Register.
For the KYBD by (refer to the KYBD controller section of this spec).
Note: IRQs are disabled if not used/selected by any Logical Device. Refer to Note A.
Note: nSMI must be disabled to use IRQ2.
Note: All IRQ’s are available in Serial IRQ mode.
Note 1: The default value of the Primary Interrupt Select register for logical device 0 is 0x06.
SMSC DS – LPC47M14X
Page 162
Rev. 03/19/2001
Table 67 – DMA Channel Select Configuration Register Description
NAME
REG INDEX
0x74 (R/W)
DEFINITION
Bits[2:0] select the DMA Channel.
0x00= Reserved
STATE
DMA Channel
C
Select
0x01= DMA1
Default=0x02 or
0x04 (Note 1)
0x02= DMA2
0x03= DMA3
0x04-0x07= No DMA active
on VCC POR,
VTR POR,
HARD RESET
and
SOFT RESET
Note: A DMA channel is activated by setting the DMA Channel Select register to [0x01-0x03] AND :
For the FDC logical device by setting DMAEN, bit D3 of the Digital Output Register.
For the PP logical device in ECP mode by setting dmaEn, bit D3 of the ecr.
Note: The DMA channel must be disabled if not used/selected by any Logical Device. Refer to Note A.
Note 1: The default value of the DMA Channel Select register for logical device 0 (FDD) is 0x02 and for logical
device 3 and 5 is 0x04.
Note A. Logical Device IRQ and DMA Operation
1)
IRQ and DMA Enable and Disable: Any time the IRQ or DMA channel for a logical block is disabled by a
register bit in that logical block, the IRQ and/or DMA channel must be disabled. This is in addition to the IRQ
and DMA channel disabled by the Configuration Registers (active bit or address not valid).
a)
FDC: For the following cases, the IRQ and DMA channel used by the FDC are disabled. Will not
respond to the DMA request.
Digital Output Register (Base+2) bit D3 (DMAEN) set to "0".
The FDC is in power down (disabled).
b)
c)
Serial Ports:
Modem Control Register (MCR) Bit D2 (OUT2) - When OUT2 is a logic "0", the serial port interrupt
is disabled.
Parallel Port:
ꢀ
ꢀ
SPP and EPP modes: Control Port (Base+2) bit D4 (IRQE) set to "0", IRQ is disabled.
ECP Mode:
(1)
(2)
(DMA) dmaEn from ecr register. See table.
IRQ - See table.
MODE
(FROM ECR REGISTER)
IRQ PIN
PDREQ PIN
CONTROLLED BY CONTROLLED BY
000
001
010
011
100
101
110
111
PRINTER
SPP
FIFO
ECP
EPP
RES
TEST
CONFIG
IRQE
IRQE
(on)
dmaEn
dmaEn
dmaEn
dmaEn
dmaEn
dmaEn
dmaEn
dmaEn
(on)
IRQE
IRQE
(on)
IRQE
d)
Keyboard Controller: Refer to the KBD section of this spec.
SMSC DS – LPC47M14X
Page 163
Rev. 03/19/2001
SMSC Defined Logical Device Configuration Registers
The SMSC Specific Logical Device Configuration Registers reset to their default values only on hard resets
generated by Vcc or VTR POR (as shown) or the PCI_RESET# signal. These registers are not affected by soft
resets.
Table 68 – Floppy Disk Controller, Logical Device 0 [Logical Device Number = 0x00]
NAME
FDD Mode Register
REG INDEX
0xF0 R/W Bit[0] Floppy Mode
DEFINITION
STATE
C
= 0
= 1
Normal Floppy Mode (default)
Enhanced Floppy Mode 2 (OS2)
Default = 0x0E
on VCC POR,
VTR POR and
HARD RESET
Bit[1] FDC DMA Mode
= 0
= 1
Burst Mode is enabled
Non-Burst Mode (default)
Bit[3:2] Interface Mode
= 11
= 10
= 01
= 00
AT Mode (default)
(Reserved)
PS/2
Model 30
Bit[4] Reserved
Bit[5] Reserved, set to zero
Bit[6] FDC Output Type Control
= 0
= 1
FDC outputs are OD12 open drain (default)
FDC outputs are O12 push-pull
Bit[7] FDC Output Control
= 0
= 1
FDC outputs active (default)
FDC outputs tri-stated
FDD Option Register
0xF1 R/W Bit[0] Forced Write Protect
= 0 Inactive (default)
C
Default = 0x00
on VCC POR,
VTR POR and
HARD RESET
= 1
FDD nWRTPRT input is forced active when
either of the drives has been selected.
nWRTPRT (to the FDC Core) = WP (FDC SRA
register, bit 1) = (nDS0 AND Forced Write Protect)
OR (nDS1 AND Forced Write Protect) OR nWRTPRT
(from the FDD Interface) OR Floppy Write Protect
Note: The Floppy Write Protect bit is in the Device
Disable register.
Note: Boot floppy is always drive 0.
Bit[1] Reserved
Bits[3:2] Density Select
= 00
= 01
= 10
= 11
Normal (default)
Normal (reserved for users)
1 (forced to logic "1")
0 (forced to logic "0")
Bit [7:4] Reserved.
0xF2 R/W Bits[1:0] Floppy Drive A Type
Bits[3:2] Floppy Drive B Type
FDD Type Register
C
C
Default = 0xFF
on VCC POR,
VTR POR and
HARD RESET
Bits[5:4] Reserved (could be used to store Floppy
Drive C type)
Bits[7:6] Reserved (could be used to store Floppy
Drive D type)
Note: The LPC47M14x supports two floppy drives
Reserved, Read as 0 (read only)
0xF3 R
SMSC DS – LPC47M14X
Page 164
Rev. 03/19/2001
Table 68 – Floppy Disk Controller, Logical Device 0 [Logical Device Number = 0x00]
NAME
REG INDEX
DEFINITION
STATE
FDD0
0xF4 R/W Bits[1:0] Drive Type Select: DT1, DT0
Bits[2] Read as 0 (read only)
C
Default = 0x00
on VCC POR,
VTR POR and
HARD RESET
Bits[4:3] Data Rate Table Select: DRT1, DRT0
Bits[5] Read as 0 (read only)
Bits[6] Precompensation Disable PTS
=0 Use Precompensation
=1 No Precompensation
Bits[7] Read as 0 (read only)
FDD1
0xF5 R/W Refer to definition and default for 0xF4
C
Table 69 – Parallel Port, Logical Device 3 [Logical Device Number = 0x03]
NAME
REG INDEX
DEFINITION
STATE
PP Mode Register
0xF0 R/W Bits[2:0] Parallel Port Mode
C
= 100
= 000
= 001
= 101
= 010
= 011
= 111
Printer Mode (default)
Default = 0x3C
on VCC POR,
VTR POR and
HARD RESET
Standard and Bi-directional (SPP) Mode
EPP-1.9 and SPP Mode
EPP-1.7 and SPP Mode
ECP Mode
ECP and EPP-1.9 Mode
ECP and EPP-1.7 Mode
Bit[6:3] ECP FIFO Threshold
0111b (default)
Bit[7] PP Interrupt Type
Not valid when the parallel port is in the Printer
Mode (100) or the Standard & Bi-directional Mode
(000).
= 1
= 0
Pulsed Low, released to high-Z.
IRQ follows nACK when parallel port in EPP
Mode or [Printer, SPP, EPP] under ECP.
IRQ level type when the parallel port is in ECP, TEST,
or Centronics FIFO Mode.
PP Mode Register 2
0xF1 R/W Bits[3:0] Reserved. Set to zero
Bit [4] TIMEOUT_SELECT
Default = 0x00
on VCC POR,
VTR POR and
HARD RESET
= 0
= 1
TMOUT (EPP Status Reg.) cleared on write of
‘1’ to TMOUT.
TMOUT cleared on trailing edge of read of
EPP Status Reg.
Bits[7:5] Reserved. Set to zero.
SMSC DS – LPC47M14X
Page 165
Rev. 03/19/2001
Table 70 – Serial Port 1, Logical Device 4 [Logical Device Number = 0x04]
NAME
Serial Port 1
REG INDEX
0xF0 R/W Bit[0] MIDI Mode
DEFINITION
STATE
C
Mode Register
= 0
= 1
MIDI support disabled (default)
MIDI support enabled
Default = 0x00
on VCC POR,
VTR POR and
HARD RESET
Bit[1] High Speed
= 0
= 1
High Speed Disabled(default)
High Speed Enabled
Bit[6:2] Reserved, set to zero
Bit[7]: Share IRQ
=0 UARTs use different IRQs
=1 UARTs share a common IRQ
See Note 1 below.
Note 1: To properly share and IRQ,
1. Configure UART1 (or UART2) to use the desired IRQ.
2. Configure UART2 (or UART1) to use No IRQ selected.
3. Set the share IRQ bit.
Note: If both UARTs are configured to use different IRQs and the share IRQ bit is set, then both of the UART IRQs
will assert when either UART generates an interrupt.
UART Interrupt Operation Table
Table 71 – Serial Port 2, Logical Device 5 [Logical Device Number = 0x05]
NAME
Serial Port 2
REG INDEX
0xF0 R/W Bit[0] MIDI Mode
DEFINITION
STATE
C
Mode Register
= 0
= 1
MIDI support disabled (default)
MIDI support enabled
Default = 0x00
on VCC POR,
VTR POR and
HARD RESET
Bit[1] High Speed
= 0
= 1
High Speed disabled(default)
High Speed enabled
Bit[4:2] Reserved, set to zero
Bit[5] TXD2_MODE (Note 1)
=0
=1
The inactive state of the TXD2 pin is low.
The inactive state of the TXD2 pin is tristate.
Bits[7:6] Reserved. Set to zero.
SMSC DS – LPC47M14X
Page 166
Rev. 03/19/2001
Table 71 – Serial Port 2, Logical Device 5 [Logical Device Number = 0x05]
NAME
REG INDEX
DEFINITION
STATE
IR Option Register
0xF1 R/W Bit[0] Receive Polarity
C
= 0
= 1
Active High (Default)
Active Low
Default = 0x02
on VCC POR,
VTR POR and
HARD RESET
Bit[1] Transmit Polarity
= 0
= 1
Active High
Active Low (Default)
Bit[2] Duplex Select
= 0
= 1
Full Duplex (Default)
Half Duplex
Bits[5:3] IR Mode
= 000
= 001
= 010
= 011
= 1xx
Standard COM Functionality (Default)
IrDA
ASK-IR
Reserved
Reserved
Bit[6] IR Location Mux
= 0
= 1
Use Serial port TXD2 and RXD2 (Default)
Use alternate IRRX2 (pin 61) and IRTX2 (pin
62).
Bit[7] Reserved, write 0.
Bits [7:0]
IR
Half
Duplex
0xF2
Timeout
These bits set the half duplex time-out for the IR port.
This value is 0 to 10msec in 100usec increments.
Default = 0x03
on VCC POR,
VTR POR and
HARD RESET
0= blank during transmit/receive
1= blank during transmit/receive + 100usec
Note 1: The TXD2_MODE bit is a VTR powered bit that is reset on VTR POR only.
SMSC DS – LPC47M14X
Page 167
Rev. 03/19/2001
Table 72 – KYBD, Logical Device 7 [Logical Device Number = 0x07]
NAME
KRST_GA20
REG INDEX
0xF0
DEFINITION
KRESET and GateA20 Select
Bit[7] Polarity Select for P12
= 0 P12 active low (default)
= 1 P12 active high
STATE
R/W
Default = 0x00
on VCC POR,
VTR POR and
HARD RESET
Bit[6] M_ISO. Enables/disables isolation of mouse
signals into 8042. Does not affect MDAT signal to
mouse wakeup (PME) logic.
1=block mouse clock and data signals into 8042
Bits[6:5] reset on
VTR POR only
0= do not block mouse clock and data signals into
8042
Bit[5] K_ISO. Enables/disables isolation of keyboard
signals into 8042. Does not affect KDAT signal to
keyboard wakeup (PME) logic.
1=block keyboard clock and data signals into 8042
0= do not block keyboard clock and data signals into
8042
Bit[4] MLATCH
= 0 MINT is the 8042 MINT ANDed with Latched
MINT (default)
= 1 MINT is the latched 8042 MINT
Bit[3] KLATCH
= 0 KINT is the 8042 KINT ANDed with Latched
KINT (default)
= 1 KINT is the latched 8042 KINT
Bit[2] Port 92 Select
= 0 Port 92 Disabled
= 1 Port 92 Enabled
Bit[1] Reserved
Bit[0] Reserved
Reserved - read as ‘0’
0xF1 -
0xFF
Table 73 – PME, Logical Device A [Logical Device Number = 0x0A]
NAME
CLKI32
REG INDEX
0xF0
DEFINITION
NOTES
Bit[7:2] Reserved
R/W
Bit [1] SPEKEY_EN. This bit is used to turn the logic
Eng.
Note 2
Default = 0x00
on VTR POR
for the “wake on specific key” feature on and
off. It will disable the 32kHz clock input to the
logic when turned off. The logic will draw no
power when disabled.
0 = “Wake on specific key” logic is on
(default)
Eng.
Note 3
1 = “Wake on specific key” logic is off
SMSC Reserved (default = 0)
Note 1
Bit [0]
Note: Bit [0] should always be zero. If this is
changed, the Fan Tachometer, the Wake on Specific
Key, and the LED blink will not function if the 14MHz
clock is removed.
SMSC DS – LPC47M14X
Page 168
Rev. 03/19/2001
NAME
REG INDEX
DEFINITION
NOTES
Bit[7:1] Reserved
Bit[0]
INT_G Enable
INT_G
0 = Disable Interrupt Generating Registers
from affecting the serial IRQ stream.
Default = 0x00
1 = Enable Interrupt Generating Registers to
drive one or more frames low in the
SER IRQ stream
0xF1
R/W
Eng.
Note 1
on VCC POR, VTR
POR,
HARD
RESET and SOFT
RESET
Note:
See runtime registers at offset 0x54 and
0x55 for configuring Interrupt Generating
Registers.
0xF2-
0xFF
Reserved – read as ‘0’
Note: The registers located in Logical Device A are runtime registers.
Note 1: SMSC Reserved registers have read/write capability. The default values set for these registers should be
maintained unless otherwise specified.
Table 74 – MPU-401 [Logical Device Number = 0x0B]
NAME
REG INDEX
DEFINITION
STATE
MPU-401
Primary 0x60 R/W Bit[0] A8
C
Base I/O Address
High Byte
Bit[1] A9
Bit[2] A10
Bit[3] A11
Bit[4] “0”
Bit[5] “0”
Bit[6] “0”
Bit[7] “0”
Default = 0x03
on HARD RESET,
SOFT RESET, VCC
POR and VTR POR
MPU-401
Primary 0x61 R/W Bit[0] “0”
C
Base I/O Address
Low Byte
Bit[1] A1
Bit[2] A2
Bit[3] A3
Bit[4] A4
Bit[5] A5
Bit[6] A6
Bit[7] A7
Default = 0x30
on HARD RESET,
SOFT RESET, VCC
POR and VTR POR
Note: Bit[0] must be “0”.
Table 75 – USB Hub, Logical Device C [Logical Device Number = 0x0C]
NAME
Activate
REG INDEX
DEFINITION
This bit has read/write capability.
Bits[7:1] Reserved (Writes are ignored and Reads
NOTES
Note 1
0x30
Bit [0]
return 0)
Note: This register has no dedicated function. The
user may use this register at their own
discretion.
Bit [0] Reserved
OSC_CLK
Bit [1] OSC_CLK
0xF0
R/W
0=48MHz clock is connected to the ICLK pin (default)
Default = 0x00
on VTR POR
1=24MHz crystal is connected to the ICLK and OCLK
pins
Bits [7:2] Reserved
SMSC DS – LPC47M14X
Page 169
Rev. 03/19/2001
NAME
REG INDEX
DEFINITION
NOTES
IdVendor_Low
Default=0x24
on VTR POR
0xF1
R/W
Bit[7:0] USB Vendor ID (assigned by USB), low byte
Default reset to SMSC ID
System
Note 1
IdVendor_High
Default=0x04
on VTR POR
IdProduct_Low
Default=40
on VTR POR
IdProduct_High
Default=01
on VTR POR
BcdDevice_Low
Default=0x00
on VTR POR
BcdDevice_High
Default=0x00
on VTR POR
0xF2
R/W
Bit[7:0] USB Vendor ID (assigned by USB), high byte
Default reset to SMSC ID
System
Note 1
Bit[7:0] USB Product ID (assigned by manufacturer), low
byte
Default reset to SMSC silicon ID
0xF3
R/W
System
Note 1
Bit[7:0] USB Product ID (assigned by manufacturer),
0xF4
R/W
System
Note 1
high byte
Default reset to SMSC silicon ID
Bit[7:0] USB Device Release Number (in binary coded
0xF5
R/W
System
Note 1
decimal), low byte
Default set to SMSC silicon revision
Bit[7:0] USB Device Release Number (in binary coded
0xF6
R/W
System
Note 1
decimal), high byte
Default set to SMSC silicon revision
Bit[0] GangedPWR
Bit[1:4] Reserved
Bit[5:6] Strp[0:1]
Bit[7] NhubReset
HubControl_1
Default=0x00
on VTR POR
0xF7
R/W
Note: For a detailed description of HubControl_1 bits
see Table 76 below.
0xF8-
0xFF
Reserved – read as ‘0’
Note 1: This activate function is satisfied by NHubReset in the HubControl 1 Register defined below.
System Note 1: Current Root Hub device identification is being implemented by using the Vendor ID (VID)
and Product ID (PID) from the hub vendor. Although this is not currently a Windows 2000 or 98 logo
requirement, Microsoft WHQL encourages system vendors to change the VID/PID combination for each of
their motherboards and USB hubs. Using the hub vendor's VID/PID (Default Value of the registers defined
above) combination becomes an issue if, in a future operating system release, WHQL finds a broken
implementation in the industry that must be disallowed. As result, all hubs using the same VID/PID
combination would be disallowed by the operating system. However, if each system vendor creates a
unique VID/PID combination, then only the disallowed implementation would be turned off.
Therefore, it is recommended that each OEM modify / change the following register values, through BIOS,
for each motherboard design by modifying the following registers defined above:
1)
2)
IdVendor_Low Default=0x24
IdVendor_High Default=0x04
3)
4)
IdProduct_Low Default=0x40
IdProduct_High Default=0x01
SMSC DS – LPC47M14X
Page 170
Rev. 03/19/2001
Table 76 – HubControl_1 Register Definition
HubControl_1
RESET=0x00
INDEX=0xF7
NAME
HUB CONTROL REGISTER 1
DESCRIPTION
NHubReset – When this bit is asserted (0), the hub controller is in a reset
state. The hub will not respond to any enumeration or device requests.
When this bit is de-asserted (1), the hub controller is ready to receive
packets from the Root Host Controller. Each Port will then be enabled via a
control packet from the Host
BIT
7
R/W
R/W
NHubReset
6
5
Strp1
Strp0
R/W
R/W
Strap Select – The two bits define the number of USB Down Stream Ports
that will be enabled. The Default value which is sampled during VT POR, is
defined by the Input Pins nStrp1 and nStrp0. The state of the input pins are
the logical invert of the associated Strp1 and Strp0 bits. The number of
ports enabled is defined in the following table:
Strp1 Strp0
Ports Enabled
Reserved – This selection is for future use
PD1+/-,PD2+/-
PD1+/-,PD2+/-,PD3+/-
PD1+/-,PD2+/-,PD3+/-,PD4+/- (Default)
1
1
0
0
1
0
1
0
Note: For backward compatibility with existing older revision
devices, the default for Strp1 and Strp0 is 00. This implies that the
input pins nStrp1 and nStrp0, are required to not be connected.
See Note 1:
4:1
0
Reserved
R
R/W
Reserved – Reads return 0
Ganged
Ganged Power Sense Enable – When this bit is set (1), the Power Control
block of the USB HUB device will internally OR the Power OK sense pins
(nUSBOC[3:0]) and Power Enable (nPWREN[3:0]) pins. This will allow the
system designer the ability to reduce implementation costs by reducing the
external current hardware. In this mode, since only one Sense and Enable
PIN is required, the unused input pins must be tied to VDD (1) and the
unused output pins may be left unconnected.
PWR
See Note 1:
Note 1: When the specified USB Down Stream Ports are disabled via the Strp0/Strp1 bit or nStrp1/nStrp0 Pins, the
associated Over-current sense pins (nUSBOC[x]) and Power Enable (nPWREN[x]) pins are also disabled. The USB
Down Stream Port nUSBOC[x] input pin can be a NC (No Connect) pin or tied High (1) and the Power Enable
(nPWREN[x]) pin will be forced low (0).
SMSC DS – LPC47M14X
Page 171
Rev. 03/19/2001
9
OPERATIONAL DESCRIPTION
9.1 MAXIMUM GUARANTEED RATINGS
Operating Temperature Range........................................................................................................................... 0oC to +70oC
Storage Temperature Range............................................................................................................................-55o to +150oC
Lead Temperature Range ............................................................................................... Refer to JEDEC Spec. J-STD-020
Positive Voltage on any pin, with respect to Ground.................................................................................................Vcc+0.3V
Negative Voltage on any pin, with respect to Ground.....................................................................................................-0.3V
Maximum Vcc...................................................................................................................................................................+5.5V
Note: Stresses above those listed above could cause permanent damage to the device. This is a stress rating only and
functional operation of the device at any other condition above those indicated in the operation sections of this
specification is not implied.
Note: When powering this device from laboratory or system power supplies, it is important that the Absolute Maximum
Ratings not be exceeded or device failure can result. Some power supplies exhibit voltage spikes on their outputs when
the AC power is switched on or off. In addition, voltage transients on the AC power line may appear on the DC output.
If this possibility exists, it is suggested that a clamp circuit be used.
9.2 DC ELECTRICAL CHARACTERISTICS
(TA = 0°C - 70°C, Vcc = +3.3 V ± 10%)
PARAMETER
SYMBOL
MIN
2.0
TYP
MAX
UNITS
COMMENTS
I Type Input Buffer
Low Input Level
VILI
VIHI
0.8
V
V
TTL Levels
High Input Level
IS Type Input Buffer
Low Input Level
VILIS
VIHIS
VHYS
0.8
V
V
Schmitt Trigger
Schmitt Trigger
High Input Level
2.2
Schmitt Trigger Hysteresis
100
mV
Input Leakage, I and IS
Buffers
Low Input Leakage
IIL
-10
-10
+10
+10
µA
µA
VIN = 0
High Input Leakage
IIH
VIN = VCC
O6 Type Buffer
Low Output Level
High Output Level
VOL
VOH
0.4
V
V
IOL = 6mA
IOH = -3mA
2.4
SMSC DS – LPC47M14X
Page 172
Rev. 03/19/2001
PARAMETER
IO8 Type Buffer
SYMBOL
MIN
TYP
MAX
UNITS
COMMENTS
Low Output Level
High Output Level
Leakage Current
O8 Type Buffer
Low Output Level
High Output Level
OD8 Type Buffer
Low Output Level
VOL
VOH
ILEAK
0.4
V
V
IOL = 8mA
IOH = -4mA
2.4
µA
VIN = 0 to VCC
(Note 1)
±10
VOL
VOH
0.4
V
V
IOL = 8mA
IOH = -4mA
2.4
VOL
0.4
V
IOL = 8mA
Leakage Current
ILEAK
+10
µA
VIN = 0 to VCC
O12 Type Buffer
Low Output Level
High Output Level
IO12 Type Buffer
Low Output Level
High Output Level
Leakage Current
OD12 Type Buffer
Low Output Level
VOL
VOH
0.4
V
V
IOL = 12mA
IOH = -6mA
2.4
2.4
VOL
VOH
ILEAK
0.4
V
V
IOL = 12mA
IOH = -6mA
µA
VIN = 0 to VCC
(Note 1)
±10
VOL
0.4
V
IOL = 12mA
Leakage Current
ILEAK
+10
µA
VIN = 0 to VCC
OD14 Type Buffer
Low Output Level
VOL
0.4
V
IOL = 14mA
Leakage Current
ILEAK
+10
µA
VIN = 0 to VCC
OP14 Type Buffer
Low Output Level
High Output Level
VOL
VOH
0.4
V
V
IOL = 14mA
IOH = -14mA
2.4
SMSC DS – LPC47M14X
Page 173
Rev. 03/19/2001
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
COMMENTS
IOP14 Type Buffer
Low Output Level
High Output Level
Leakage Current
IOD16 Type Buffer
Low Output Level
Leakage Current
O24 Type Buffer
Low Output Level
High Output Level
VOL
VOH
ILEAK
0.4
V
V
IOL = 14mA
IOH = -14mA
2.4
µA
VIN = 0 to VCC
(Note 1)
±10
VOL
0.4
V
IOL = 16mA
ILEAK
µA
VIN = 0 to VCC
(Note 1)
±10
VOL
0.4
V
IOL = 24 mA @ VCC
VOH
IIL
2.4
V
µA
IOH = -12 mA @ VCC
VCC = 0V
VIN = 5.5V Max
Backdrive
± 10
Protect/ChiProtect
(All signal pins excluding
LAD[3:0], LDRQ#, LPCPD#,
LFRAME#,
USB+,
USB-,
PD+[1:4], PD-[1:4])
5V Tolerant Pins
IIL
± 10
± 10
µA
µA
VCC = 3.3V
(All signal pins excluding
VIN = 5.5V Max
LAD[3:0], LDRQ#, LPCPD#,
LFRAME#,
USB+,
USB-,
PD+[1:4], PD-[1:4])
Inputs and Outputs in High
Impedance State
LPC Bus Pins
IIL
VCC = 0V and
VCC = 3.3V
VIN = 3.6V Max
(LAD[3:0], LDRQ#, LPCPD#,
LFRAME#)
IOUSB Input Levels:
Differential Input Sensitivity
VDI
VCM
VSE
0.2
0.8
V
V
V
|(PD+) - (PD-)|
(Notes 3 & 6)
Differential Common Mode
Range
(Note 3)
2.5
Includes VDI range
Single-Ended Receiver
Threshold
(Note 3)
0.8
Note 4
2.0
Note 5
SMSC DS – LPC47M14X
Page 174
Rev. 03/19/2001
PARAMETER
IOUSB Output Levels:
Static Output Low
(Note 3)
SYMBOL
VOL
MIN
0.0
TYP
MAX
0.3
UNITS
COMMENTS
RL of 15 KΩ to
V
V
GND
Static Output High
(Note 3)
VOH
2.8
3.6
RL of 1.5 KΩ to
3.6V
Output Signal Crossover
Voltage
VCRS
ICCI
1.3
2.0
V
(Note 3)
VCC Supply Current Active
20
mA
All outputs open,
all inputs at a fixed
state (i.e., 0V or
3.3V.
Trickle Supply Voltage
VTR
VCC
min
-.5V
VCC
V
VCC must not be
greater than .5V
above VTR
max
VTR Supply Current Active
ITRI
4
20
mA
All outputs ,
all inputs at a fixed
state (i.e., 0V or
3.3V.
Reference Voltage
VREF
5.5
V
VREF can be either
3.3V (nominal) or
5V (nominal)
VREF Supply Current Active
IRFI
8
mA
All outputs open,
all inputs at a fixed
state (i.e., 0V or
3.3V.
Note 1: All output leakage’s are measured with the current pins in high impedance
Note 2: Output leakage is measured with the low driving output off, either for a high level output or a high impedance
state.
Note 3: Voltages are measured from the local ground potential, unless otherwise specified.
Note 4: This minimum value is referred to as VIL in the USB Spec 1.1
Note 5: This maximum value is referred to as VIH in the USB Spec 1.1
Note 6: This input sensitivity is valid when both differential data inputs are in the differential common
mode range.
SMSC DS – LPC47M14X
Page 175
Rev. 03/19/2001
Capacitance values for Signal Pins
CAPACITANCE TA = 25°C; fc = 1MHz; VCC = 3.3V ±10%
LIMITS
TYP
PARAMETER
Clock Input Capacitance
SYMBOL
MIN
MAX
20
UNIT
pF
TEST CONDITION
All pins except pin
under test tied to AC
ground
CIN
Input Capacitance
Output Capacitance
CIN
COUT
10
20
pF
pF
Input Capacitance for the USB HUB Interface Pins (Note 1)
Downstream Port
CIND
CINUB
150
100
pF
pF
Upstream Port (w/o cable)
Note 1: The input capacitance of a port is measured at the connector pins
SMSC DS – LPC47M14X
Page 176
Rev. 03/19/2001
10 TIMING DIAGRAMS
For the Timing Diagrams shown, the following capacitive loads are used on outputs.
CAPACITANCE
TOTAL (pF)
NAME
SER_IRQ
LAD# [3:0]
LDRQ#
50
50
50
nDIR
nSTEP
240
240
nDS0
nDS1
240
240
PD[0:7]
nSTROBE
nALF
240
240
240
J1X-Y
J2X-Y
50
50
KDAT
240
KCLK
MDAT
240
240
MCLK
240
MIDI_Tx
FANx
50
50
LEDx
50
TXD1
TXD2
50
50
PD+[1:4] (Full-Speed)
PD-[1:4] (Full-Speed)
USB+ (Full-Speed)
USB− (Full-Speed)
PD+[1:4] (Low-Speed)
PD-[1:4] (Low-Speed)
USB+ (Low-Speed)
USB− (Low-Speed)
50
50
50
50
200-450 (Note 1)
200-450 (Note 1)
50-150
50-150
Note 1: Total capacitance of load with cable.
SMSC DS – LPC47M14X
Page 177
Rev. 03/19/2001
t 1
t 2
V c c
t 3
A ll H o s t
A c c e s s e s
FIGURE 9 – POWER-UP TIMING
NAME
DESCRIPTION
MIN
300
100
125
TYP
MAX
UNITS
µs
t1
t2
t3
Vcc Slew from 2.7V to 0V
Vcc Slew from 0V to 2.7V
µs
All Host Accesses After Powerup (Note 1)
500
µs
Note 1: Internal write-protection period after Vcc passes 2.7 volts on power-up
USB Hub Interface Timing
The USB Hub uses a differential output driver to drive the USB data signal onto the USB cable. The output rise time
and fall times are measured between 10% and 90% of the signal (see FIGURE 10). Rise and fall time requirements
apply to differential transitions as well as to transitions between differential and single-ended signaling.
The rise and fall times for full-speed buffers are much more stringent than that of low speed buffers. These values,
listed in Table 77, are measured with a load of 50pF and are matched to within ±10% to minimize RFI emissions and
signal skew.
The rise and fall times for low-speed buffers are measure with the loads shown in FIGURE 12. A downstream port is
allowed 150pF of input/output capacitance (CIND). A low-speed device (including cable) may have a capacitance of
as little as 200pF and as much as 450pF. This gives a range of 200pF to 600pF as the capacitive load that the
downstream low-speed buffer must support. Upstream buffers on low-speed devices must be designed to drive the
capacitance of the attached cable plus an additional 150pF. In all cases, the edges must be matched to within ±20%
to minimize RFI emissions and signal skew.
Table 77 – Electrical Source Characteristics
The values listed below satisfy speeds up to 12Mbps (Full Speed)
CONDITIONS
PARAMETER
DRIVER
CHARACTERISTICS:
SYM
(NOTES 1, 2, 3)
MIN
MAX
UNIT
DRIVER CHARACTERISTICS (Full-Speed)
Transition Time:
Note 4,5 and FIGURE 10
& FIGURE 11
CL = 50 pF
CL = 50 pF
Rise Time
Fall Time
TR
TF
4
4
20
20
ns
ns
SMSC DS – LPC47M14X
Page 178
Rev. 03/19/2001
CONDITIONS
(NOTES 1, 2, 3)
(TR/TF)
PARAMETER
SYM
TRFM
MIN
90
MAX
111.11
UNIT
%
Differential Rise/Fall Time
Matching
Note 9
Drive Output Impedance
ZDRV
Steady State Drive
28
44
Ω
DRIVER CHARACTERISTICS (Low-Speed)
Transition Time:
Note 4,5 and FIGURE 10
Rise Time
TR
FIGURE 12
75
300
ns
Fall Time
TF
TRFM
FIGURE 12
(TR/TF)
75
80
300
125
ns
%
Differential Rise/Fall Time
Matching
Note 9
DATA TRANSFER TIMINGS
Full Speed Data Rate
Frame Interval
11.9700
0.9995
80
12.0300
1.0005
86
TDRATE
TFRAME
TPERIOD
Notes 8, 10, & 12
Note 8
Mbs
ms
ns
Clock Period
Note 10
Source
Jitter
Total
Note 6, 7, & 9
(including
tolerance):
frequency
FIGURE 14
To next Transition
TDJ1
TDJ2
TDEOP
-3.5
-4.0
-2
3.5
4.0
5
ns
ns
ns
For Paired Transitions
Source
Jitter
for
Note 7 and FIGURE 15
Note 7 and FIGURE 16
Differential Transition to
SEO Transition
Receiver Jitter:
To next Transition
TJR1
TJR2
TEOPT
-18.5
-9
160
18.5
9.0
175
ns
ns
ns
For Paired Transitions
Source SEO interval of
Note 7 and FIGURE 15
Note 7 and FIGURE 15
Note 11
EOP
Receiver SEO interval of
EOP
TEOPR
TFST
82
ns
ns
Width of SEO interval
14
during
differential
transition
Note 1: All voltages are measured from the local ground potential, unless otherwise specified.
Note 2: All timing use a capacitive load (CL) to ground of 50pF, unless otherwise specified.
Note 3: Full speed timings have a 1.5KΩ pull-up to a voltage of 3.0V - 3.6V on the D+ data line.
Note 4: Measured from 10% to 90% of the data signals.
Note 5: The rising and falling edges should be smoothly transitioning (monotonic).
Note 6: Timing differences between the differential data signals.
Note 7: Measured at crossover point of differential data signals.
Note 8: For a more detailed description of the Data Signaling Rate and the Frame Interval see sections 7.1.11 and
7.1.12 in the USB Spec 1.1.
Note 9: Excluding the first transition from the idle state.
Note 10: The accuracy of the host controller’s data rate must be known and controlled to better than
±0.05%
Note 11: During differential signal transitions both PD+ and PD- may temporarily be less that
VIH(min). This period can be up to 14ns.
Note 12: The data-rate tolerance for host, hub, and full-speed functions is ±0.25%
SMSC DS – LPC47M14X
Page 179
Rev. 03/19/2001
Rise Time
Fall Time
90%
90%
Differential
Data Lines
VCRS
10%
10%
tR
tF
FIGURE 10 – DATA SIGNAL RISE AND FALL TIME
Full-Speed Buffer
Rs
TxD+
CL
Rs
TxD-
CL
Full Speed: 4 to 20ns at C = 50pF
L
The output impedance of the buffer with a series resistance
(Rs) is 28 to 44 .
Note:
Ω
Ω
FIGURE 11 – FULL SPEED LOAD
Low-Speed Buffer
Rs
Low-Speed Buffer
Rs
TxD+
TxD-
TxD+
3.6V
15K
CL
CL
CL
CL
1.5K
Rs
Rs
TxD-
15K
CL = 200pF to 600pF
CL = 50pF to 150pF
Low-Speed upstream port load
Low-Speed Downstream port load
FIGURE 12 – LOW-SPEED PORT LOADS
Round Trip
Cable Delay
80ns (max)
Driver End
of Cable
50%Point of
Initial Swing
VSS
One Way
Cable
Delay
30ns
Data Line
Crossover
Point
Receiver
End of Cable
(max)
VSS
FIGURE 13 – CABLE DELAY
SMSC DS – LPC47M14X
Page 180
Rev. 03/19/2001
TPERIOD
Crossover
Points
Differential
Data Lines
Consecutive
Transitions
N * TPERIOD + TxDJ1
Paired
Transitions
N * TPERIOD + TxDJ2
FIGURE 14 – DIFFERENTIAL DATA JITTER
Crossover
TPERIOD
Points Extended
Crossover
Points
Differential
Data Lines
Diff. Data-to-
SEO Skew
Source EOP Width:
Receiver EOP Width:
TEOPT
TEOPR
N * TPERIOD + TxDEOP
FIGURE 15 – DIFFERENTIAL TO EOP TRANSITION SKEW AND EOP WIDTH
TPERIOD
Differential
Data Lines
TJR
TJR1
TJR2
Consecutive
Transitions
N * TPERIOD + TJR1
Paired
Transitions
N * TPERIOD + TJR2
FIGURE 16 – RECEIVER JITTER TOLERANCE
SMSC DS – LPC47M14X
Page 181
Rev. 03/19/2001
t1
CLOCKI
t2
t2
FIGURE 17 – INPUT CLOCK TIMING
DESCRIPTION MIN
20
NAME
TYP
69.84
35
31.25
16.53
MAX
UNITS
ns
ns
µs
µs
t1
t2
t1
t2
Clock Cycle Time for 14.318MHZ
Clock High Time/Low Time for 14.318MHz
Clock Cycle Time for 32KHZ
Clock High Time/Low Time for 32KHz
Clock Rise Time/Fall Time (not shown)
5
ns
t1
t4
t2
t5
t3
P C I_C LK
FIGURE 18 – PCI CLOCK TIMING
NAME
DESCRIPTION
MIN
30
12
TYP
MAX
33.3
UNITS
nsec
nsec
nsec
nsec
nsec
t1
t2
t3
t4
Period
High Time
Low Time
Rise Time
12
3
3
t5 ꢀ
Fall Time
t4
PCI RESET#
FIGURE 19 – RESET TIMING
NAME
t4
DESCRIPTION
PCI_RESET# width (Note 1)
MIN
TYP MAX
UNITS
µs
Note 1: The PCI_RESET# width is dependent upon the processor clock. The PCI_RESET# must be active while
the clock is running and stable.
SMSC DS – LPC47M14X
Page 182
Rev. 03/19/2001
CLK
t1
Output Delay
t2
t3
Tri-State Output
FIGURE 20 – OUTPUT TIMING MEASUREMENT CONDITIONS, LPC SIGNALS
NAME
DESCRIPTION
CLK to Signal Valid Delay – Bused Signals
Float to Active Delay
MIN
2
2
TYP
MAX
11
11
UNITS
ns
ns
t1
t2
t3
Active to Float Delay
28
ns
t1
t2
CLK
Inputs Valid
Input
FIGURE 21 – INPUT TIMING MEASUREMENT CONDITIONS, LPC SIGNALS
NAME
t1
t2
DESCRIPTION
Input Set Up Time to CLK – Bused Signals
Input Hold Time from CLK
MIN
7
0
TYP
MAX
UNITS
ns
ns
SMSC DS – LPC47M14X
Page 183
Rev. 03/19/2001
PCI_CLK
LFRAME#
LAD[3:0]
L1
L2
Address
Data
TAR
Sync=0110
L3
TAR
FIGURE 22 – I/O WRITE
Note: L1=Start; L2=CYCTYP+DIR; L3=Sync of 0000
PCI_CLK
LFRAME#
L1
L2
Address
TAR
Sync=0110
L3
Data
TAR
LAD[3:0]
FIGURE 23 – I/O READ
Note: L1=Start; L2=CYCTYP+DIR; L3=Sync of 0000
SMSC DS – LPC47M14X
Page 184
Rev. 03/19/2001
PCI_CLK
LDRQ#
Start
MSB
LSB
ACT
FIGURE 24 – DMA REQUEST ASSERTION THROUGH LDRQ#
PCI_CLK
LFRAME#
LAD[3:0]
Start C+D CHL Size
TAR
Sync=0101
L1
Data
TAR
FIGURE 25 – DMA WRITE (FIRST BYTE)
Note: L1=Sync of 0000
PCI_CLK
LFRAME#
LAD[3:0]
Start C+D CHL Size
Data
TAR
Sync=0101
L1
TAR
FIGURE 26 – DMA READ (FIRST BYTE)
Note: L1=Sync of 0000
SMSC DS – LPC47M14X
Page 185
Rev. 03/19/2001
nDIR
t3
t4
nSTEP
t1
t2
t9
t5
nDS0-1
nINDEX
t6
t7
t8
nRDATA
nWDATA
FIGURE 27 – FLOPPY DISK DRIVE TIMING (AT MODE ONLY)
NAME
t1
DESCRIPTION
nDIR Set Up to STEP Low
MIN
TYP
4
MAX
UNITS
X*
t2
t3
t4
t5
nSTEP Active Time Low
nDIR Hold Time after STEP#
nSTEP Cycle Time
nDS0 & nDS1 Hold Time from nSTEP Low (Note)
nINDEX Pulse Width
24
96
132
20
2
X*
X*
X*
X*
t6
X*
t7
nRDATA Active Time Low
40
ns
t8
t9
nWDATA Write Data Width Low
nDS0 & nDS1, Setup Time nDIR Low (Note)
.5
Y*
ns
0
*X specifies one MCLK period and Y specifies one WCLK period.
MCLK = 16 x Data Rate (at 500 kb/s MCLK = 8 MHz)
WCLK = 2 x Data Rate (at 500 kb/s WCLK = 1 MHz)
Note: The DS0 &DS1 setup and hold times must be met by software.
SMSC DS – LPC47M14X
Page 186
Rev. 03/19/2001
t1
t2
t3
nWRITE
PD<7:0>
t4
t5
t6
t7
nDATASTB
nADDRSTB
t8
t9
nWAIT
FIGURE 28 – EPP 1.9 DATA OR ADDRESS WRITE CYCLE
NAME
DESCRIPTION
MIN
60
60
0
10
5
TYP
MAX
185
185
UNITS
ns
ns
ns
ns
ns
ns
ns
t1
t2
t3
t4
t5
t6
t7
nWAIT Asserted to nWRITE Asserted (Note 1)
nWAIT Asserted to nWRITE Change (Note 1)
nWAIT Asserted to PDATA Invalid (Note 1)
PDATA Valid to Command Asserted
nWRITE to Command Asserted
nWAIT Asserted to Command Asserted (Note 1)
nWAIT Deasserted to Command Deasserted
(Note 1)
35
210
190
60
60
t8
t9
Command Asserted to nWAIT Deasserted
Command Deasserted to nWAIT Asserted
0
0
10
s
ns
Note 1: nWAIT must be filtered to compensate for ringing on the parallel bus cable. nWAIT is considered
to have settled after it does not transition for a minimum of 50 nsec.
SMSC DS – LPC47M14X
Page 187
Rev. 03/19/2001
t1
t3
t2
nWRITE
PD<7:0>
t4
t5
t6
t7
t8
t9
t10
DATASTB
ADDRSTB
t11
t12
nWAIT
FIGURE 29 – EPP 1.9 DATA OR ADDRESS READ CYCLE
NAME
t1
t2
t3
t4
t5
t6
t7
t8
t9
t10
DESCRIPTION
MIN
0
60
60
0
0
60
0
TYP
MAX
UNITS
nWAIT Asserted to nWRITE Deasserted
nWAIT Asserted to nWRITE Modified (Notes 1,2)
nWAIT Asserted to PDATA Hi-Z (Note 1)
Command Asserted to PDATA Valid
Command Deasserted to PDATA Hi-Z
nWAIT Asserted to PDATA Driven (Note 1)
PDATA Hi-Z to Command Asserted
nWRITE Deasserted to Command
nWAIT Asserted to Command Asserted
nWAIT Deasserted to Command Deasserted
(Note 1)
185
190
180
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
190
30
1
0
60
195
180
t11
t12
PDATA Valid to nWAIT Deasserted
PDATA Hi-Z to nWAIT Asserted
0
0
ns
µs
Note 1: nWAIT is considered to have settled after it does not transition for a minimum of 50 ns.
Note 2: When not executing a write cycle, EPP nWRITE is inactive high.
SMSC DS – LPC47M14X
Page 188
Rev. 03/19/2001
t1
t2
nWRITE
PD<7:0>
t3
t4
nDATASTB
nADDRSTB
t5
nWAIT
FIGURE 30 – EPP 1.7 DATA OR ADDRESS WRITE CYCLE
NAME
DESCRIPTION
MIN
0
50
10
5
TYP
MAX
40
UNITS
ns
ns
ns
ns
t1
t2
t3
t4
t5
Command Deasserted to nWRITE Change
Command Deasserted to PDATA Invalid
PDATA Valid to Command Asserted
nWRITE to Command
35
35
Command Deasserted to nWAIT Deasserted
0
ns
nWRITE
t1
t2
PD<7:0>
nDATASTB
nADDRSTB
t3
nWAIT
FIGURE 31 – EPP 1.7 DATA OR ADDRESS READ CYCLE
NAME
DESCRIPTION
MIN
0
0
TYP
MAX
UNITS
ns
ns
t1
t2
t3
Command Asserted to PDATA Valid
Command Deasserted to PDATA Hi-Z
Command Deasserted to nWAIT Deasserted
0
ns
SMSC DS – LPC47M14X
Page 189
Rev. 03/19/2001
ECP PARALLEL PORT TIMING
Parallel Port FIFO (Mode 101)
The standard parallel port is run at or near the peak 500KBytes/sec allowed in the forward direction using DMA. The
state machine does not examine nACK and begins the next transfer based on Busy. Refer to FIGURE 32.
ECP Parallel Port Timing
The timing is designed to allow operation at approximately 2.0 Mbytes/sec over a 15ft cable. If a shorter cable is used
then the bandwidth will increase.
Forward-Idle
When the host has no data to send it keeps HostClk (nStrobe) high and the peripheral will leave PeriphClk (Busy) low.
Forward Data Transfer Phase
The interface transfers data and commands from the host to the peripheral using an interlocked PeriphAck and HostClk.
The peripheral may indicate its desire to send data to the host by asserting nPeriphRequest.
The Forward Data Transfer Phase may be entered from the Forward-Idle Phase. While in the Forward Phase the
peripheral may asynchronously assert the nPeriphRequest (nFault) to request that the channel be reversed. When the
peripheral is not busy it sets PeriphAck (Busy) low. The host then sets HostClk (nStrobe) low when it is prepared to send
data. The data must be stable for the specified setup time prior to the falling edge of HostClk. The peripheral then sets
PeriphAck (Busy) high to acknowledge the handshake. The host then sets HostClk (nStrobe) high. The peripheral then
accepts the data and sets PeriphAck (Busy) low, completing the transfer. This sequence is shown in FIGURE 33.
The timing is designed to provide 3 cable round-trip times for data setup if Data is driven simultaneously with HostClk
(nStrobe).
Reverse-Idle Phase
The peripheral has no data to send and keeps PeriphClk high. The host is idle and keeps HostAck low.
Reverse Data Transfer Phase
The interface transfers data and commands from the peripheral to the host using an interlocked HostAck and PeriphClk.
The Reverse Data Transfer Phase may be entered from the Reverse-Idle Phase. After the previous byte has been
accepted the host sets HostAck (nALF) low. The peripheral then sets PeriphClk (nACK) low when it has data to send.
The data must be stable for the specified setup time prior to the falling edge of PeriphClk. When the host is ready to
accept a byte it sets HostAck (nALF) high to acknowledge the handshake. The peripheral then sets PeriphClk (nACK)
high. After the host has accepted the data it sets HostAck (nALF) low, completing the transfer. This sequence is shown
in FIGURE 34.
Output Drivers
To facilitate higher performance data transfer, the use of balanced CMOS active drivers for critical signals (Data,
HostAck, HostClk, PeriphAck, PeriphClk) are used in ECP Mode. Because the use of active drivers can present
compatibility problems in Compatible Mode (the control signals, by tradition, are specified as open-collector), the
drivers are dynamically changed from open-collector to totem-pole. The timing for the dynamic driver change is
specified in then IEEE 1284 Extended Capabilities Port Protocol and ISA Interface Standard, Rev. 1.14, July 14,
1993, available from Microsoft. The dynamic driver change must be implemented properly to prevent glitching the
outputs.
SMSC DS – LPC47M14X
Page 190
Rev. 03/19/2001
t6
t3
PD<7:0>
t1
t2
t5
nSTROBE
t4
BUSY
FIGURE 32 – PARALLEL PORT FIFO TIMING
NAME
DESCRIPTION
PDATA Valid to nSTROBE Active
nSTROBE Active Pulse Width
PDATA Hold from nSTROBE Inactive (Note 1)
nSTROBE Active to BUSY Active
BUSY Inactive to nSTROBE Active
BUSY Inactive to PDATA Invalid (Note 1)
MIN
600
600
450
TYP
MAX
UNITS
ns
ns
ns
ns
t1
t2
t3
t4
t5
t6
500
680
80
ns
ns
Note 1: The data is held until BUSY goes inactive or for time t3, whichever is longer. This only applies if another data
transfer is pending. If no other data transfer is pending, the data is held indefinitely.
t3
nALF
t4
PD<7:0>
t2
t1
t7
t8
nSTROBE
BUSY
t6
t5
t6
FIGURE 33 – ECP PARALLEL PORT FORWARD TIMING
NAME
DESCRIPTION
nALF Valid to nSTROBE Asserted
PDATA Valid to nSTROBE Asserted
BUSY Deasserted to nALF Changed
(Notes 1,2)
MIN
0
0
TYP
MAX
60
60
UNITS
ns
ns
t1
t2
t3
80
180
ns
t4
t5
t6
t7
t8
BUSY Deasserted to PDATA Changed (Notes 1,2)
nSTROBE Asserted to Busy Asserted
nSTROBE Deasserted to Busy Deasserted
BUSY Deasserted to nSTROBE Asserted (Notes 1,2)
BUSY Asserted to nSTROBE Deasserted (Note 2)
80
0
0
80
80
180
ns
ns
ns
ns
ns
200
180
Note 1: Maximum value only applies if there is data in the FIFO waiting to be written out.
Note 2: BUSY is not considered asserted or deasserted until it is stable for a minimum of 75 to 130 ns.
SMSC DS – LPC47M14X
Page 191
Rev. 03/19/2001
t2
PD<7:0>
t1
t5
t6
nACK
nALF
t4
t3
t4
FIGURE 34 – ECP PARALLEL PORT REVERSE TIMING
NAME
DESCRIPTION
PDATA Valid to nACK Asserted
nALF Deasserted to PDATA Changed
nACK Asserted to nALF Deasserted
(Notes 1,2)
nACK Deasserted to nALF Asserted (Note 2)
nALF Asserted to nACK Asserted
nALF Deasserted to nACK Deasserted
MIN
0
0
TYP
MAX
UNITS
ns
ns
t1
t2
t3
80
200
200
ns
t4
t5
t6
80
0
0
ns
ns
ns
Note 1: Maximum value only applies if there is room in the FIFO and terminal count has not been received. ECP can
stall by keeping nALF low.
Note 2: nACK is not considered asserted or deasserted until it is stable for a minimum of 75 to 130 ns.
SMSC DS – LPC47M14X
Page 192
Rev. 03/19/2001
DATA
0
1
0
1
0
0
1
1
0
1
1
t2
t1
t2
t1
IRRX
n IRRX
Parameter
min
typ
max
units
t1 Pulse Width at 1 15kba ud
t1 Pulse Wid th at 57.6kba ud
t1 Pulse Wid th at 38.4kba ud
t1 Pulse Wid th at 19.2kba ud
t1 Pu lse Width a t 9.6kba ud
t1 Pu lse Width a t 4.8kba ud
t1 Pu lse Width a t 2.4kba ud
t2 Bit Time at 1 15kba ud
t2 Bit Time at 57.6kba ud
t2 Bit Time at 38.4kba ud
t2 Bit Time at 19.2kba ud
t2 Bi t Time a t 9.6kba ud
t2 Bi t Time a t 4.8kba ud
t2 Bi t Time a t 2.4kba ud
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.6
3.22
4.8
9.7
19.5
39
2.71
3.69
5.53
11.07
22.13
44.27
88.55
µs
µs
µs
µs
µs
µs
µs
µs
µs
µs
µs
µs
µs
µs
78
8.68
17.4
26
52
104
208
416
No te s:
1. Receive Pu lse Detection C rite ria: A re ceived p ulse is considered d etecte d if the
receivedpulse is a minimum of 1.41µs.
2. IR RX: L5, CRF 1 Bit 0 = 1
nIRCRF1 Bit 0 = 0 default
FIGURE 35 – IRDA RECEIVE TIMING
SMSC DS – LPC47M14X
Page 193
Rev. 03/19/2001
DATA
IRTX
1
0
1
0
0
1
1
1
1
0
0
t2
t1
t2
t1
n I RT X
mi n
Parameter
typ
max
units
1.41
1.41
1.41
1.41
1.41
1.41
1.41
t1
Pulse Width at 115kbaud
Pulse Width at 57.6kbaud
Pulse Width at 38.4kbaud
Pulse Width at 19.2kbaud
Pulse Width at 9.6kbaud
Pulse Width at 4.8kbaud
Pulse Width at 2.4kbaud
Bit Time at 115kbaud
Bit Time at 57.6kbaud
Bit Time at 38.4kbaud
Bit Time at 19.2kbaud
Bit Time at 9.6kbaud
1.6
3.22
4.8
2.71
3.69
µ s
µ s
µ s
µ s
µ s
µ s
µ s
µ s
µ s
µ s
µ s
µ s
µ s
µ s
t1
t1
t1
t1
t1
t1
t2
t2
t2
t2
t2
t2
t2
5.53
9.7
11.07
22.13
44.27
88.55
19.5
39
78
8.68
17.4
26
52
104
208
416
Bit Time at 4.8kbaud
Bit Time at 2.4kbaud
Notes:
1. IrDA @ 115k is HPSIR compatible.
IrDA @ 2400 willallow compatibility with HP95LX
and 48SX.
2. IRT X: L5, CRF 1 B it 1 = 1 (def ault)
nIRTX: L5, CRF1 Bit 1 =0
FIGURE 36 – IRDA TRANSMIT TIMING
SMSC DS – LPC47M14X
Page 194
Rev. 03/19/2001
DATA
0
1
0
1
0
0
1
1
0
1
1
t1
t2
IRRX
n IRRX
t3
t5
t4
MIRRX
t6
nM IRRX
Parameter
min
typ
max
units
t1
t2
t3
t4
t5
t6
M odu lated Out put Bit T ime
Off Bit Time
µ s
µ s
µ s
µ s
µ s
µ s
M odu lated Outp ut " On"
M odu lated Out put " Off"
M odu lated Outp ut " On"
M odu lated Out put " Off"
0.8
0.8
0.8
0.8
1
1
1
1
1.2
1.2
1.2
1.2
Notes:
1 . IRRX: L 5, CRF1 Bit 0 = 1
n IRRX: L5 , CRF 1 Bit 0 = 0 (de fault)
M IRRX, nMI RRX are the mod ulate d ou tpu ts
FIGURE 37 – AMPLITUDE SHIFT KEYED IR RECEIVE TIMING
SMSC DS – LPC47M14X
Page 195
Rev. 03/19/2001
DATA
0
1
0
1
0
0
1
1
0
1
1
t1
t2
IRTX
n IRT X
t3
t5
t4
t6
MIRT X
nMIRTX
Parameter
min
typ
max
units
t1
t2
t3
t4
t5
t6
Modu lated Out put Bit Time
Off Bit Time
Modu lated Outp ut "On"
Modu lated Outp ut "Off"
Modu lated Outp ut "On"
Modu lated Outp ut "Off"
µ s
µ s
µ s
µ s
µ s
µ s
0.8
0.8
0.8
0.8
1
1
1
1
1.2
1.2
1.2
1.2
Note s:
1 . IRTX: L5 , CRF1 Bit 1 =1 (def ault)
nI RTX: L 5, CRF1 Bit 1 = 0
MIRTX, nMIRTXa re the mod ulate d ou tpu ts
FIGURE 38 – AMPLITUDE SHIFT KEYED IR TRANSMIT TIMING
SMSC DS – LPC47M14X
Page 196
Rev. 03/19/2001
PCI_CLK
SER_IRQ
t1
t2
FIGURE 39 – SETUP AND HOLD TIME
NAME
t1
t2
DESCRIPTION
SER_IRQ Setup Time to PCI_CLK Rising
SER_IRQ Hold Time to PCI_CLK Rising
MIN
7
0
TYP
MAX
UNITS
nsec
nsec
Data
Stop (1-2 Bits)
Data (5-8 Bits)
Start
Parity
t1
TXD1, 2
FIGURE 40 – SERIAL PORT DATA
NAME
t1
DESCRIPTION
Serial Port Data Bit Time
MIN
TYP
tBR
MAX
UNITS
nsec
1
Note 1: tBR is 1/Baud Rate. The Baud Rate is programmed through the divisor latch registers. Baud Rates have
percentage errors indicated in the “Baud Rate” table in the “Serial Port” section.
VREF
2
3
VREF +/- 5%
J1X, J1Y,
J2X, J2Y
t1
FIGURE 41 – JOYSTICK POSITION SIGNAL
NAME
t1
DESCRIPTION
Rise Time to 2/3 VREF
MIN
20
TYP
MAX
UNITS
µsec
90%
10%
90%
10%
J1B1, J1B2,
J2B1, J2B2
t1
FIGURE 42 – JOYSTICK BUTTON SIGNAL
DESCRIPTION MIN
t2
NAME
TYP
MAX
10
UNITS
µsec
t1, t2 Button Fall/Rise Time
SMSC DS – LPC47M14X
Page 197
Rev. 03/19/2001
CLK
1
t3 t4
CLK
2
CLK
9
CLK
10
CLK
11
KCLK/
MCLK
t5
t2
t6
t1
KDAT/ Start Bit
Bit 0
Bit 7
Parity Bit Stop Bit
MDAT
FIGURE 43 – KEYBOARD/MOUSE RECEIVE/SEND DATA TIMING
NAME
t1
DESCRIPTION
Time from DATA transition to falling edge of CLOCK
MIN
5
TYP
MAX
25
UNITS
µsec
(Receive)
t2
Time from rising edge of CLOCK to DATA transition
(Receive)
5
T4-5
µsec
t3
t4
t5
Duration of CLOCK inactive (Receive/Send)
Duration of CLOCK active (Receive/Send)
30
30
>0
50
50
50
µsec
µsec
µsec
Time to keyboard inhibit after clock 11 to ensure the
keyboard does not start another transmission (Receive)
t6
Time from inactive to active CLOCK transition, used to
time when the auxiliary device samples DATA (Send)
5
25
µsec
Idle (No Data)
Data
Idle (No Data)
Stop Bit
Start Bit
t1
Data
MIDI_Tx
FIGURE 44 – MIDI DATA BYTE
DESCRIPTION
NAME
t1
MIN
31.7
TYP
32
MAX
32.3
UNITS
µsec
MIDI Data Bit Time
Note: The MIDI bit clock is 31.25kHz +/- 1%
SMSC DS – LPC47M14X
Page 198
Rev. 03/19/2001
t1
t2
FANx
FIGURE 45 – FAN OUTPUT TIMING
NAME
t1
t2
DESCRIPTION
PWM Period (Note 1)
PWM High Time (Note 2)
MIN
0.021
0.00033
TYP
MAX
25.5
25.1
UNITS
msec
msec
Note 1: The period is 1/fout,where fout is programmed through the FANx and Fan Control registers. The tolerance on
fout is +/- 2%.
Note 2: When Bit 0 of the FANx registers is 0, then the duty cycle is programmed through Bits[6:1] of these
registers. If Bits[6:1] = “000000” then the FANx pin is low. The duty cycle is programmable through
Bits[6:1] to be between 1.56% and 98.44%. When Bit 0 is 1, the FANx pin is high.
t1
t2
t3
FAN_TACHx
FIGURE 46 – FAN TACHOMETER INTPUT TIMING
NAME
DESCRIPTION
Pulse Time (1/2 Revolution Time=30/RPM)
Pulse High Time
MIN
4tTACH
3tTACH
tTACH
TYP
MAX
UNITS
µsec
µsec
1
1
t1
t2
t3
Pulse Low Time
µsec
Note 1: tTACH is the clock used for the tachometer counter. It is 30.52 * DVSR, where the divisor (DVSR) is
programmed in the Fan Control register.
t1
t2
LEDx
FIGURE 47 – LED OUTPUT TIMING
NAME
t1
t2
DESCRIPTION
MIN
1
0
TYP
MAX
2
UNITS
sec
sec
Period
Blink ON Time
0.51
Note 1: The blink rate is programmed through Bits[1:0] in LEDx register. When Bits[1:0]=00, LED is OFF.
Bits[1:0]=01 indicates LED blink at 1Hz rate with a 50% duty cycle (0.5 sec ON, 0.5 sec OFF). Bits[1:0]=10
indicates LED blink at ½ Hz rate with a 25% duty cycle (0.5 sec ON, 1.5 sec OFF). When Bits[1:0]=11, LED
is ON.
SMSC DS – LPC47M14X
Page 199
Rev. 03/19/2001
11 PACKAGE OUTLINE
Note: The following package information is preliminary. Contact SMSC for the latest information.
FIGURE 48 – 128 PIN QFP PACKAGE OUTLINE
MIN
~
NOMINAL
MAX
3.4
REMARKS
Overall Package Height
Standoff
A
A1
A2
D
~
~
0.05
2.55
23.70
11.85
19.90
17.70
8.85
13.90
~
0.5
~
3.05
24.10
12.05
20.10
18.10
9.05
14.10
~
Body Thickness
23.90
11.95
20.0
17.90
8.95
14.00
~
X Span
D/2
D1
E
1/2 X Span Measured from Centerline
X body Size
Y Span
E/2
E1
H
1/2 Y Span Measured from Centerline
Y body Size
Lead Frame Thickness
Lead Foot Length
Lead Length
L
0.73
~
0.88
1.95
0.5 Basic
~
1.03
~
L1
e
Lead Pitch
0o
0.10
0.13
7o
0.30
~
Lead Foot Angle
Lead Width
W
~
~
R1
Lead Shoulder Radius
R2
ccc
ccc
0.13
~
~
~
~
~
0.30
0.0762
0.08
Lead Foot Radius
Coplanarity (Assemblers)
Coplanarity (Test House)
Notes:
1 Controlling Unit: millimeter
2 Tolerance on the position of the leads is + 0.04 mm maximum.
3 Package body dimensions D1 and E1 do not include the mold protrusion.
Maximum mold protrusion is 0.25 mm.
4 Dimension for foot length L measured at the gauge plane 0.25 mm above the seating plane.
5 Details of pin 1 identifier are optional but must be located within the zone indicated
SMSC DS – LPC47M14X
Page 200
Rev. 03/19/2001
12 APPENDIX - TEST MODE
12.1 BOARD TEST MODE
Board test mode can be entered as follows:
On the rising (deasserting) edge of PCI_RESET#, drive LFRAME# low and drive LAD[0] low.
Exit board test mode as follows:
On the rising (deasserting) edge of PCI_RESET#, drive either LFRAME# or LAD[0] high.
See the “XNOR-Chain Test Mode” section below for a description of this board test mode.
12.1.1 XNOR-Chain Test Mode
XNOR-Chain test structure allows users to confirm that all pins are in contact with the motherboard during assembly
and test operations. See FIGURE 49 below.
The XNOR-Chain test structure must be activated to perform these tests. When the XNOR-Chain is activated, the
LPC47M14x pin functions are disconnected from the device pins, which all become input pins except for one output
pin at the end of XNOR-Chain.
The tests that are performed when the XNOR-Chain test structure is activated require the board-level test hardware
to control the device pins and observe the results at the XNOR-Chain output pin.
The PCI_RESET# pin is not included in the XNOR-Chain. The XNOR-Chain output pin# is 85, GP31/FAN_TACH.
See the following subsections for more details.
I/O#1
I/O#2
I/O#3
I/O#n
XNor
Out
FIGURE 49 – XNOR-CHAIN TEST STRUCTURE
SMSC DS – LPC47M14X
Page 201
Rev. 03/19/2001
Introduction
The LPC47M14x provides board test capability through the XNOR chain. When the chip is in the XNOR chain test
mode, setting the state of any of the input pins to the opposite of its current state will cause the output of the chain to
toggle.
All pins on the chip are inputs to the XNOR chain, with the exception of the following:
1)
2)
3)
4)
5)
VCC (pins 53, 65, 93, & 125), VTR (pins 18, 113, & 122), and VREF (pin 44).
VSS (pins 7, 31, 60, 76, 101, 102, & 128) and AVSS (pin 40).
TXD1 (pin 85) This is the chain output.
nPCI_RESET (pin 26).
OCLK (pin 124)
To put the chip in the XNOR chain test mode, tie LAD0 (pin 20) and LFRAME# (pin 24) low. Then toggle
PCI_RESET# (pin 26) from a low to a high state. Once the chip is put into XNOR chain test mode, LAD0 (pin 20) and
LFRAME# (pin 24) become part of the chain.
To exit the XNOR chain test mode tie LAD0 (pin 20) or LFRAME# (pin 24) high. Then toggle PCI_RESET# (pin 26)
from a low to a high state. A VCC POR will also cause the XNOR chain test mode to be exited. To verify the test
mode has been exited, observe the output at TXD1 (pin 85). Toggling any of the input pins should not cause its state
to change.
Setup
Warning: Ensure power supply is off during setup.
1)
2)
3)
4)
Connect VSS (pins 7, 31, 60, 76, 101, 102, & 128) and AVSS (pin 40) to ground.
Connect VCC (pins 53, 65, 93, & 125), VTR (pins 18, 113, & 122), and VREF (pin 44)to VCC (3.3V).
Connect an oscilloscope or voltmeter to TXD1 (pin 85).
All other pins should be tied to ground.
Testing
1)
Turn power on.
2)
With LAD0 (pin 20) and LFRAME# (pin 24), low, bring PCI_RESET# (pin 26) high. The chip is now in XNOR
chain test mode. At this point, all inputs to the XNOR chain are low. The output, on TXD1 (pin 85), should
also be low. Refer to INITIAL CONFIG on Truth Table 1.
3)
4)
Bring pin 127 high. The output on TXD1 (pin 85) should go high. Refer to STEP ONE on Truth Table 1.
In descending pin order, bring each input high. The output should switch states each time an input is toggled.
Continue until all inputs are high. The output on TXD1 should now be low. Refer to END CONFIG on Truth
Table 1.
5)
6)
The current state of the chip is now represented by INITIAL CONFIG in Truth Table 2.
Each input should now be brought low, starting at pin one and continuing in ascending order. Continue until
all inputs are low. The output on TXD1 should now be low. Refer to Truth Table 2.
To exit test mode, tie LAD0 (pin 20) OR LFRAME# (pin 24) high, and toggle PCI_RESET# from a low to a
high state.
7)
SMSC DS – LPC47M14X
Page 202
Rev. 03/19/2001
TRUTH TABLE 1 - Toggling Inputs in Descending Order
PIN
PIN
PIN
PIN
PIN
OUTPUT
PIN 85
L
127
126
125
124
123
PIN ...
PIN 1
INITIAL CONFIG
L
L
L
L
L
L
L
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
…
H
H
H
H
H
…
H
L
H
H
H
H
…
H
L
L
H
H
H
…
H
L
L
L
H
H
…
H
L
L
L
L
L
L
L
L
L
L
L
L
L
H
L
H
L
H
…
H
L
H
…
H
…
H
…
L
STEP N
END CONFIG
H
H
H
H
H
H
H
L
TRUTH TABLE 2 - Toggling Inputs in Ascending Order
OUTPUT
PIN 85
L
PIN 1 PIN 2 PIN 3 PIN 4 PIN 5
PIN ...
H
PIN 127
INITIAL CONFIG
H
H
H
H
H
H
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
L
L
L
L
L
…
L
H
L
L
L
L
…
L
H
H
L
L
L
…
L
H
H
H
L
L
…
H
H
H
H
L
…
L
H
H
H
H
H
…
L
H
H
H
H
H
…
H
H
L
H
L
H
…
L
STEP N
L
END CONFIG
L
L
L
L
L
L
L
L
SMSC DS – LPC47M14X
Page 203
Rev. 03/19/2001
13 REFERENCE DOCUMENTS
1)
2)
3)
4)
5)
6)
7)
SMSC Consumer Infrared Communications Controller (CIrCC) V1.X
IEEE 1284 Extended Capabilities Port Protocol and ISA Standard, Rev. 1.14, July 14, 1993.
Hardware Description of the 8042, Intel 8 bit Embedded Controller Handbook.
PCI Bus Power Management Interface Specification, Rev. 1.0, Draft, March 18, 1997.
Low Pin Count (LPC) Interface Specification, Revision 1.0, September 29, 1997, Intel Document.
Universal Serial Bus (USB) Specification, Revision 1.1, September 23, 1998
Advanced Configuration and Power interface Specification, Revision 1.0
SMSC DS – LPC47M14X
Page 204
Rev. 03/19/2001
14 LPC47M14X REVISIONS
DATE
PAGE(S)
SECTION/FIGURE/ENTRY
CORRECTION
See italicized text
See italicized text
REVISED
03/19/01
03/19/01
03/19/01
1
3
10
Features
General Description
DESCRIPTION OF PIN FUNCTIONS
Changes to Note 4 (see
italicized text)
21
22
Field Definitions
See italicized text
03/19/01
03/19/01
I/O Read and Write Cycles, DMA Read and See the “Low Pin Count
Write Cycles, CLOCKRUN Protocol, LPCPD (LPC) Interface
Protocol, SYNC Protocol
Specification” Revision
1.0 (See italicized text)
23
34
I/O Transfers
Bit 5 Non-DMA
See italicized text
03/19/01
03/19/01
Reserved, read ‘0’.
This part does not
support non-DMA
mode.
40
41
Non-DMA Mode - Transfers from the FIFO to This part does not
03/19/01
03/19/01
the Host, Non-DMA Mode - Transfers from the support non-DMA
Host to the FIFO
mode.
Table 17
–
Description of Command Non-DMA Mode Flag -
Write ‘0’. This part does
not support non-DMA
Symbols
mode.
94
POWER MANAGEMENT
Note added (see
03/19/01
italicized text)
113
119
Note 5 under table
(see italicized text)
03/19/01
03/19/01
Fan Tachometer Inputs, second paragraph The divisor for each fan
under fan count equation
is programmable via
the Fan Control
Register, which is
located in the Runtime
Register block at offset
0xFA.
125
127
156
Table 58
Summary
–
Runtime Register Block Changes to Note 5 (see
03/19/01
03/19/01
03/19/01
italicized text)
Table 59 – PME, SMI, GPIO, FAN Register Changes to Note 6 (see
Description
italicized text)
Table 62 – Chip Level Registers
0x22 R/W Address - 0:
Power Off or Disabled
1: Power On or
Enabled
0x23 R/W Address -
(see Note in the “FDC
Power Management”
section.)
168
172
Table 72 – KYBD, Logical Device 7 [Logical KRST_GA20 - Bits[6:5]
03/19/01
03/19/01
Device Number = 0x07]
DC Electrical Characteristics
reset on VTR POR only
Values added to:
V
CC Supply Current
Active, VTR Supply
Current Active and VREF
Supply Current Active
200
PACKAGE OUTLINE
Note added (see
italicized text)
03/19/01
SMSC DS – LPC47M14X
Page 205
Rev. 03/19/2001
相关型号:
©2020 ICPDF网 联系我们和版权申明