LE150S-CD [SLPOWER]
150W Single Output LED Driver Series;
| 型号： | LE150S-CD |
| 厂家： | 
SL Power Electronics |
| 描述： | 150W Single Output LED Driver Series |
| 文件： | 总4页 (文件大小：943K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LE150S-CD
150W Single Output
LED Driver Series
Features
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
High Efficiency (up to 93%)
Wide Range Universal Input 90-305 VAC
Active Power Factor Correction (0.99 typical)
Constant Current Output
Dimming Function
Lightning Protection
Waterproof (IP67)
Overcurrent, Overvoltage, Overtemperature
Protection
ꢀ
ꢀ
Meets UL8750 & EN61347 Safety
3 Year Warranty
Description
The LE150S-CD Series operate from a 90 ~ 305Vac input range. These units will provide up to a 1.4 A of
output current and a maximum output voltage of 214Vdc for 150 W maximum output power. They are designed
to be highly efficient and highly reliable. The standard features include dimming control, lightning protection,
over voltage protection, short circuit protection, and over temperature protection.
Model Selection
Model
Number
Output
Current
Output
Voltage
Efficiency*
Ripple &
Noise**
Regulation
Line
Overvoltage
Trip Level
110Vac
220Vac
Load
LE150S140CD
1330mA-1470mA
53V – 107V
89%-90%
91%-92%
3.2V pk-pk max.
128V – 161V
1%
3%
3%
LE150S70CD
665mA-735mA
107V – 214V
90%-91%
92%-93%
6.5V pk-pk max.
257V – 321V
1%
Notes:
1. Efficiency measured at full load, at input voltage noted.
2. Measured at 20MHz bandwidth, with noise probe directly across output terminals, and load terminated with 0.1µF ceramic and 10µF low ESR electrolytic
capacitors.
General Specifications
2.0 seconds, max.
AC Input 90-305Vac, 47-63Hz, 1∅
Turn On Time
1-10Vdc source or External Resistor can be
used for dimming control. See below.
Dimming
Function
100Vac: 1.8A, 220Vac: 0.9A
230Vac, cold start: will not exceed 65A
XA, 250VAC fuses provided on all models
<0.75mA@277Vac, 50Hz
Input Current
Inrush Current
Input Fuses
Constant Current
Overload
Protection
Provided - no damage to unit, self-recovery.
Short Circuit
Protection
Latch mode. AC input will need to be reset to
return to normal operation after an OVP
condition. See chart for trip range.
Earth Leakage
Current
Overvoltage
Protection
Latch mode. AC input will need to be reset
To return to normal operation after an OTP
condition. Trip Temperature = 110°C typical.
Overtemperature
Protection
See Models chart.
Efficiency
150W continuous
Output Power
www.slpower.com
LE150S-CD REV 2.0, 11-FEB-13
1
LE150S-CD
150W Single Output
LED Driver Series
General Specifications (continued)
Operating
Temperature
Operating: -35°C to +70°C
Non-operating: -40°C to +85°C
See chart
Ripple and Noise
Output Voltage
Total Regulation
Dimensions
10% to 100% operating
5% to 100%, non-operating
See chart
Relative Humidity
Safety Standards
MTBF
UL8750, UL935, UL1012, CSA-C22.2 No. 107.1,
EN61347-1, EN61347-2-13
+/- 3%. See chart
W: 3.13” x L: 9.37” x H: 1.81”
1500g
340,000 hours (1400mA model, 110Vac input,
80% load, 25°C ambient, per MIL-HDBK-217F).
58,000 hours (1400mA model, at 110Vac input,
80% load, 45°C ambient temperature).
Weight
Lifetime
EMI/EMC Compliance
EN55015, Radiated & Conducted with 6db of margin
Emissions
EN61547
EMI for Lighting Equipment
Static Discharge Immunity
Radiated RF Immunity
EFT/Burst Immunity
EN61000-4-2, 4kV Contact Discharge, 8kV air discharge
EN61000-4-3
EN61000-4-4
EN61000-4-5, 2kV line-line, 4kV line-earth
EN61000-4-6
Line Surge Immunity
Conducted RF Immunity
Power Frequency Magnetic Field Immunity
Voltage Dip Immunity
EN61000-4-8
EN61000-4-11
EN61000-3-2
Line Harmonic Emissions
Flicker Test
EN61000-3-3
Derating Curves
Mechanical Drawing
www.slpower.com
LE150S-CD REV 2.0, 11-FEB-13
2
LE150S-CD
150W Single Output
LED Driver Series
Dimming Control
The dimming function shown below uses an internal pull-up resistor, with the output at full load when the dimming leads are not connected (floated).
Parameters:
Parameter
Min.
9.8V
Typ.
10V
Max.
Notes
10V Output Voltage
10.2V
10V Output Source Current
0mA
-2V
-
-
-
10mA
12V
Absolute Max. Voltage on the 1-10V input
Source Current on the 1-10V input
0mA
1mA
Value of Rin (resistor inside the LED Driver, which is located
between the 1-10V input and 10V output
19.8K
20K
20.2K
3
LE150S-CD
150W Single Output
LED Driver Series
LE150SXXXCD
Dimming Configuration using External Voltage
LE150SXXXCD
Dimming Configuration using External Resistance
Dimming Control Notes:
1. Io is actual output current and Ir is rated current without dimming control.
2. For the driver to operate properly, the load voltage must be maintained above the minimum voltage threshold (approx. 50% of the max. output voltage for any
given model).
3. If the output voltage is maintained above 50% of the maximum output voltage, the dimming control may be operated over the entire 1-10V range with output
current varying from 100% down to practically 10%.
4. The dimming signal is allowed to be less than 1V, however, when it for 0-1V, the output current is 10% Io.
5. The internal resistor Rin is 20K, and Vcc is about 15V.
6. Do not connect the GND of dimming to the output; otherwise, the LED driver cannot work normally.
Data Sheet © 2012 SL Power Electronics Corp. The information and specifications contained herein are believed to be correct at the time of publication. However, SL Power accepts no responsibility for
consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice.
www.slpower.com
LE150S-CD REV 2.0, 11-FEB-13
4
相关型号：
©2020 ICPDF网 联系我们和版权申明