SI5321-H-ZL4 [SILICON]
Support Circuit, 1-Func, PBGA63, 9 X 9 MM, ROHS COMPLIANT, PLASTIC, MO-192AAB-1, BGA-63;型号: | SI5321-H-ZL4 |
厂家: | SILICON |
描述: | Support Circuit, 1-Func, PBGA63, 9 X 9 MM, ROHS COMPLIANT, PLASTIC, MO-192AAB-1, BGA-63 ATM 异步传输模式 电信 电信集成电路 |
文件: | 总34页 (文件大小:1515K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Si5321
SONET/SDH PRECISION CLOCK MULTIPLIER IC
Features
Ultra-low jitter clock output with jitter
generation as low as 0.3 psRMS
Digital hold for loss-of-input clock
Support for 255/238 (15/14),
255/237 (85/79), and 66/64 FEC scaling
(ITU-T G.709 and IEEE 802.3ae)
Selectable loop bandwidth
Loss-of-signal alarm output
Low power
No external components (other than a
resistor and bypassing)
Input clock ranges at 19, 39, 78, 155,
311, or 622 MHz
Output clock ranges at 19, 39, 78, 155,
311, 622, 1244, or 2488 MHz
Maximum range includes 693 MHz for
10 GbE FEC support
321
Small size (9 x 9 mm)
Backwards compatible with Si5320
Ordering Information:
Applications
See page 30.
SONET/SDH line/port cards
Terabit routers
Core switches
Digital cross connects
Description
The Si5321 is a precision clock multiplier that exceeds the requirements of high-speed
communication systems, including OC-192/OC-48 and 10 Gigabit Ethernet. This device
phase locks to an input clock in the 19, 39, 78, 155, 311 or 622 MHz frequency range
and generates a frequency-multiplied clock output that can be configured for operation
in the 19, 39, 78, 155, 622, 1244, or 2488 MHz frequency range. Silicon Laboratories
DSPLL® technology provides PLL functionality with unparalleled performance. It
eliminates external loop filter components, provides programmable loop parameters,
and simplifies design. FEC rates are supported by selectable forward and reverse 255/
238 (15/14), 255/237 (85/79), and 66/64 (33/32) conversion factors. The ITU-T G.709
255/237 rate and the IEEE 802.3ae 66/64 rate are supported when using a 155 MHz or
higher rate input clock. The performance and integration of Silicon Laboratories’ Si5321
clock IC provides high-level support of the latest specifications and systems. It operates
from a single 3.3 V supply.
Functional Block Diagram
REXT
VSEL33
VDD
GND
Biasing & Supply Regulation
FXDDELAY
CAL_ACTV
DH_ACTV
CLKIN+
CLKIN–
2
DSPLL®
÷
CLKOUT+
CLKOUT–
÷
2
VALTIME
LOS
FRQSEL[2:0]
Signal
Detect
3
2
2
Calibration
RSTN/CAL
BWBOOST
FEC[2:0]
BWSEL[1:0]
INFRQSEL[2:0]
Rev. 2.5 8/08
Copyright © 2008 by Silicon Laboratories
Si5321
Si5321
2
Rev. 2.5
Si5321
TABLE OF CONTENTS
SECTION
PAGE
1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.1. DSPLL
2.2. Clock Input and Output Rate Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.3. PLL Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
2.4. Loss-of-Signal Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
2.5. Digital Hold of the PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
2.6. Hitless Recovery from Digital Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
2.7. Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
2.8. PLL Self-Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
2.9. Bias Generation Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
2.10. Differential Input Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
2.11. Differential Output Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
2.12. Power Supply Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
2.13. Design and Layout Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
3. Pin Descriptions: Si5321 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
4. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
5. Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
6. 9x9 mm PBGA Card Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Rev. 2.5
3
Si5321
1. Electrical Specifications
Table 1. Recommended Operating Conditions
1
1
Parameter
Symbol
Test Condition
Typ
Unit
Min
Max
2
Ambient Temperature
T
–20
3.135
25
85
°C
V
A
3
Si5321 Supply Voltage , 3.3 V Supply
V
3.3
3.465
DD33
Notes:
1. All minimum and maximum specifications are guaranteed and apply across the recommended operating conditions.
Typical values apply at nominal supply voltages and an operating temperature of 25 °C unless otherwise stated.
2. The Si5321 is guaranteed by design to operate at –40° C. All electrical specifications are guaranteed for an ambient
temperature of –20 to 85° C.
3. The Si5321 specifications are guaranteed when using the recommended application circuit (including component
tolerance) of Figure 5 on page 16.
4
Rev. 2.5
Si5321
CLKIN+
CLKIN–
VIS
A. Operation with Single-Ended Clock Input*
Note: W hen using single-ended clock sources, the unused clock
input on the Si5321 must be ac-coupled to ground.
CLKIN+
0.5 VID
CLKIN–
(CLKIN+) – (CLKIN–)
VID
B. Operation with Differential Clock Input
Note: Transmission line termination, when required, must be provided
externally.
Figure 1. CLKIN Voltage Characteristics
80%
20%
tF
tR
Figure 2. Rise/Fall Time Measurement
(C LK IN+ ) - (C LK IN - )
0 V
tL O S
Figure 3. Transitionless Period on CLKIN for Detecting a LOS Condition
Rev. 2.5
5
Si5321
Table 2. DC Characteristics, VDD = 3.3 V
(VDD33 = 3.3 V ±5%, TA = –20 to 85 °C)
Parameter
Symbol
IDD
Test Condition
Min
Typ
Max
Unit
622.08 MHz In,
19.44 MHz Out
—
141
155
mA
Supply Current 1
IDD
19.44 MHz In,
622.08 MHz Out
—
—
135
145
mA
Supply Current 2
Power Dissipation Using 3.3 V Supply
Clock Output
Common Mode Input Voltage1,2,3
(CLKIN)
Single-Ended Input Voltage2,3,4
(CLKIN)
Differential Input Voltage Swing2,3,4
(CLKIN)
PD
19.44 MHz In,
622.08 MHz Out
445
1.5
479
2.0
mW
V
VICM
VIS
1.0
200
200
—
See Figure 1A
See Figure 1B
—
—
5004
5004
—
mVPP
mVPP
k
VID
RIN
VOD
Input Impedance
(CLKIN+, CLKIN–)
80
Differential Output Voltage Swing
(CLKOUT)
100 Load
Line-to-Line,
750
825
1100
mVPP
FRQSEL[0:2] = 011
Output Common Mode Voltage
(CLKOUT)
VOCM
100 Load
Line-to-Line
1.4
1.8
2.2
V
Output Short to GND (CLKOUT)
Output Short to VDD25 (CLKOUT)
Input Voltage Low (LVTTL Inputs)
Input Voltage High (LVTTL Inputs)
Input Low Current (LVTTL Inputs)
Input High Current (LVTTL Inputs)
Internal Pulldowns (LVTTL Inputs)
Input Impedance (LVTTL Inputs)
Output Voltage Low (LVTTL Outputs)
Output Voltage High (LVTTL Outputs)
Notes:
ISC(–)
ISC(+)
VIL
–60
—
—
15
—
—
—
—
—
—
—
—
—
—
mA
mA
V
—
0.8
—
VIH
IIL
2.0
—
V
50
50
50
—
A
A
A
k
V
IIH
—
Ipd
—
RIN
VOL
VOH
50
—
IO = 0.5 mA
IO = 0.5 mA
0.4
—
2.0
V
1. The Si5321 device provides weak 1.5 V internal biasing that enables ac-coupled operation.
2. Clock inputs may be driven differentially or single-endedly. When driven single-endedly, the unused input should be ac-
coupled to ground.
3. Transmission line termination, when required, must be provided externally.
4. Although the Si5321 device can operate with input clock swings as high as 1500 mV , Silicon Laboratories recommends
PP
maintaining the input clock amplitude below 500 mV for optimal performance.
PP
6
Rev. 2.5
Si5321
Table 3. AC Characteristics
(VDD33 = 3.3 V ±5%, TA = –20 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Input Clock Frequency (CLKIN)
FEC[2:0] = 000 (non FEC)
INFRQSEL[2:0] = 001
INFRQSEL[2:0] = 010
INFRQSEL[2:0] = 011
INFRQSEL[2:0] = 100
INFRQSEL[2:0] = 101
INFRQSEL[2:0] = 110
fCLKIN
No FEC Scaling,
FXDDELAY = 1
19.436
38.872
77.744
155.48
310.97
621.95
—
—
—
—
—
—
21.685
43.369 MHz
86.738
173.48
346.95
693.90
Input Clock Frequency (CLKIN)
FEC[2:0] = 001 (forward FEC)
INFRQSEL[2:0] = 001
INFRQSEL[2:0] = 010
INFRQSEL[2:0] = 011
INFRQSEL[2:0] = 100
INFRQSEL[2:0] = 101
INFRQSEL[2:0] = 110
fCLKIN
fCLKIN
fCLKIN
fCLKIN
255/238 FEC Scaling,
FXDDELAY = 1
18.142
36.284
72.568
145.13
290.27
580.54
—
—
—
—
—
—
20.239
40.478 MHz
80.955
161.91
323.82
647.64
Input Clock Frequency (CLKIN)
FEC[2:0] = 010 (reverse FEC)
INFRQSEL[2:0] = 001
INFRQSEL[2:0] = 010
INFRQSEL[2:0] = 011
INFRQSEL[2:0] = 100
INFRQSEL[2:0] = 101
INFRQSEL[2:0] = 110
238/255 FEC Scaling,
FXDDELAY = 1
20.826
41.652
83.305
166.61
333.22
666.44
—
—
—
—
—
—
23.234
46.465 MHz
92.934
185.87
371.74
743.47
Input Clock Frequency (CLKIN)
FEC[2:0] = 100 (forward FEC)
INFRQSEL[2:0] = 001
INFRQSEL[2:0] = 010
INFRQSEL[2:0] = 011
INFRQSEL[2:0] = 100
INFRQSEL[2:0] = 101
INFRQSEL[2:0] = 110
255/237 FEC Scaling
Minimum input frequency is
in the 155 MHz range,
FXDDELAY = 1
N/A
N/A
N/A
144.52
289.05
578.11
N/A
N/A
N/A
—
—
—
N/A
N/A
N/A
161.23
322.46
644.92
MHz
Input Clock Frequency (CLKIN)
FEC[2:0] = 101 (reverse FEC)
INFRQSEL[2:0] = 001
INFRQSEL[2:0] = 010
INFRQSEL[2:0] = 011
INFRQSEL[2:0] = 100
INFRQSEL[2:0] = 101
INFRQSEL[2:0] = 110
237/255 FEC Scaling
Minimum input frequency is
in the 155 MHz range,
FXDDELAY = 1
N/A
N/A
N/A
167.31
334.62
669.25
N/A
N/A
N/A
—
—
—
N/A
N/A
N/A
186.66
373.31
746.61
MHz
Note: The Si5321 provides a 1/32x, 1/16x, 1/8x, 1/4x, 1/2x, 1x, 2x, 4x, 8x, 16x, 32x, 64x, or 128x clock multiplication function
with an option for additional frequency scaling by a factor of 255/238, 238/255, 255/237, 237/255, 66/64, or 64/66 for
FEC rate conversion.
Rev. 2.5
7
Si5321
Table 3. AC Characteristics (Continued)
(VDD33 = 3.3 V ±5%, TA = –20 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Input Clock Frequency (CLKIN)
FEC[2:0] = 110 (forward FEC)
INFRQSEL[2:0] = 001
INFRQSEL[2:0] = 010
INFRQSEL[2:0] = 011
INFRQSEL[2:0] = 100
INFRQSEL[2:0] = 101
INFRQSEL[2:0] = 110
fCLKIN
66/64 FEC Scaling
Minimum input frequency is
in the 155 MHz range,
FXDDELAY = 1
N/A
N/A
N/A
150.79
301.58
603.16
N/A
N/A
N/A
—
—
—
N/A
N/A
N/A
168.22
336.44
672.88
MHz
Input Clock Frequency (CLKIN)
FEC[2:0] = 111 (reverse FEC)
INFRQSEL[2:0] = 001
INFRQSEL[2:0] = 010
INFRQSEL[2:0] = 011
INFRQSEL[2:0] = 100
INFRQSEL[2:0] = 101
INFRQSEL[2:0] = 110
fCLKIN
64/66 FEC Scaling
Minimum input frequency is
in the 155 MHz range,
FXDDELAY = 1
N/A
N/A
N/A
160.36
320.72
641.46
N/A
N/A
N/A
—
—
—
N/A
N/A
N/A
178.90
357.80
715.59
MHz
Input Clock Rise Time (CLKIN)
Input Clock Fall Time (CLKIN)
Input Clock Duty Cycle
tR
tF
Figure 2
Figure 2
—
—
40
—
—
50
11
11
60
ns
ns
%
CDUTY_IN
CLKOUT Frequency Range
FRQSEL[2:0] = 001
FRQSEL[2:0] = 000
FRQSEL[2:0] = 100
FRQSEL[2:0] = 010
FRQSEL[2:0] = 101
FRQSEL[2:0] = 011
FRQSEL[2:0] = 110
FRQSEL[2:0] = 111
fO_19
fO_39
fO_78
fO_155
fO_311
fO_622
fO_1250
fO_2500
19.436
38.872
77.744
155.48
310.97
621.95
1243.9
2487.8
—
—
—
—
—
—
—
—
21.685
43.369
86.738
173.48
346.95
693.90
1387.8
2775.6
MHz
CLKOUT Rise Time
tR
Figure 2; differential; after
3 cm of 50 FR4 stripline,
FRQSEL[0:2] = 011
—
—
48
20
190
190
—
220
220
52
ps
ps
%
CLKOUT Fall Time
tF
Figure 2; differential; after
3 cm of 50 FR4 stripline,
FRQSEL[0:2] = 011
Output Clock Duty Cycle
RSTN/CAL Pulse Width
CDUTY_OUT
Differential:
(CLKOUT+) – (CLKOUT–),
FRQSEL[0:2] = 011
tRSTN
—
—
ns
Note: The Si5321 provides a 1/32x, 1/16x, 1/8x, 1/4x, 1/2x, 1x, 2x, 4x, 8x, 16x, 32x, 64x, or 128x clock multiplication function
with an option for additional frequency scaling by a factor of 255/238, 238/255, 255/237, 237/255, 66/64, or 64/66 for
FEC rate conversion.
8
Rev. 2.5
Si5321
Table 3. AC Characteristics (Continued)
(VDD33 = 3.3 V ±5%, TA = –20 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Transitionless Period Required
on CLKIN for Detecting a LOS
Condition.
INFRQSEL[2:0] = 001
INFRQSEL[2:0] = 010
INFRQSEL[2:0] = 011
INFRQSEL[2:0] = 100
INFRQSEL[2:0] = 101
INFRQSEL[2:0] = 110
tLOS
Figure 3
24
16
12
10
9
32
/
/
/
/
/
/
—
—
—
—
—
—
/
/
/
/
/
/
fo_622
fo_622
fo_622
fo_622
fo_622
fo_622
fo_622
fo_622
fo_622
fo_622
fo_622
fo_622
32
32
32
32
32
s
8
Recovery Time for Clearing an
LOS Condition
VALTIME = 0
tVAL
Measured from when a
valid reference clock is
applied until the LOS flag
clears
1.6
90
—
—
3.2
220
ms
VALTIME = 1
Note: The Si5321 provides a 1/32x, 1/16x, 1/8x, 1/4x, 1/2x, 1x, 2x, 4x, 8x, 16x, 32x, 64x, or 128x clock multiplication function
with an option for additional frequency scaling by a factor of 255/238, 238/255, 255/237, 237/255, 66/64, or 64/66 for
FEC rate conversion.
Rev. 2.5
9
Si5321
Table 4. AC Characteristics (PLL Performance Characteristics)
(VDD33 = 3.3 V ±5%, TA = –20 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ Max Unit
Wander/Jitter at 800 Hz Bandwidth
(BWSEL[1:0] = 10 and BWBOOST = 0; FXDDELAY = 1)
Jitter Tolerance (see Figure 7)
JTOL(PP)
f = 8 Hz
1000
100
10
—
—
—
—
—
ns
ns
ns
ps
f = 80 Hz
f = 800 Hz
—
—
CLKOUT RMS Jitter Generation
FEC[2:0] = 000
JGEN(RMS)
JGEN(RMS)
JGEN(PP)
JGEN(PP)
12 kHz to 20 MHz
50 kHz to 80 MHz
12 kHz to 20 MHz
50 kHz to 80 MHz
12 kHz to 20 MHz
50 kHz to 80 MHz
12 kHz to 20 MHz
50 kHz to 80 MHz
BW = 800 Hz
0.9
1.2
—
0.27 0.35 ps
0.9 1.2 ps
0.27 0.35 ps
CLKOUT RMS Jitter Generation
FEC[2:0] = 001, 010, 100, 101, 110, 111
—
—
CLKOUT Peak-Peak Jitter Generation
FEC[2:0] = 000
—
7.6
3.6
6.7
3.0
800
0.0
11
10.0 ps
9.2 ps
10.0 ps
Hz
0.05 dB
ps
—
CLKOUT Peak-Peak Jitter Generation
FEC[2:0] = 001, 010, 100, 101, 110, 111
—
—
Jitter Transfer Bandwidth (see Figure 6)
Wander/Jitter Transfer Peaking
FBW
JP
—
—
< 800 Hz
—
Wander/Jitter at 1600 Hz Bandwidth
(BWSEL[1:0] = 10 and BWBOOST = 1; FXDDELAY = 1)
Jitter Tolerance (see Figure 7)
f = 16 Hz
f = 160 Hz
500
50
5
—
—
—
—
ns
ns
ns
ps
ps
f = 1600 Hz
—
—
CLKOUT RMS Jitter Generation
FEC[2:0] = 000
JGEN(RMS)
12 kHz to 20 MHz
50 kHz to 80 MHz
12 kHz to 20 MHz
50 kHz to 80 MHz
BW = 1600 Hz
< 1600 Hz
—
—
—
—
—
—
.80
.25
6.4
3.0
1600
0.0
1.0
.30
CLKOUT Peak-Peak Jitter Generation
FEC[2:0] = 000
JGEN(PP)
10.0 ps
5.0
—
ps
Jitter Transfer Bandwidth (see Figure 6)
Wander/Jitter Transfer Peaking
Notes:
FBW
JP
Hz
0.05 dB
1. Higher PLL bandwidth settings provide smaller clock output wander with temperature gradient.
2. For reliable device operation, temperature gradients should be limited to 10 °C/min.
3. Telcordia GR-1244-CORE requirements specify maximum phase transient slope during clock rearrangement in terms
of nanoseconds per millisecond. The equivalent ps/s unit is used here since the maximum phase transient magnitude
for the Si5321 (tPT_MTIE) never reaches one nanosecond.
10
Rev. 2.5
Si5321
Table 4. AC Characteristics (PLL Performance Characteristics) (Continued)
(VDD33 = 3.3 V ±5%, TA = –20 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ Max Unit
Wander/Jitter at 1600 Hz Bandwidth
(BWSEL[1:0] = 01 and BWBOOST = 0; FXDDELAY = 1)
Jitter Tolerance (see Figure 9)
JTOL(PP)
f = 16 Hz
1000
100
10
—
—
—
—
—
ns
ns
ns
ps
f = 160 Hz
f = 1600 Hz
—
—
CLKOUT RMS Jitter Generation
FEC[2:0] = 000
JGEN(RMS)
JGEN(RMS)
JGEN(PP)
JGEN(PP)
12 kHz to 20 MHz
50 kHz to 80 MHz
12 kHz to 20 MHz,
50 kHz to 80 MHz,
12 kHz to 20 MHz,
50 kHz to 80 MHz,
12 kHz to 20 MHz,
50 kHz to 80 MHz,
BW = 1600 Hz
< 1600 Hz
0.8
1.2
—
0.27 0.35 ps
0.9 1.2 ps
0.27 0.35 ps
CLKOUT RMS Jitter Generation
FEC[2:0] = 001, 010, 100, 101, 110, 111
—
—
CLKOUT Peak-Peak Jitter Generation
FEC[2:0] = 000
—
6.7
3.0
10.0 ps
5.0 ps
10.0 ps
—
CLKOUT Peak-Peak Jitter Generation
FEC[2:0] = 001, 010, 100, 101, 110, 111
—
6.5
—
3.0
5.0
—
ps
Hz
dB
Jitter Transfer Bandwidth (see Figure 6)
Wander/Jitter Transfer Peaking
FBW
JP
—
1600
0.0
—
0.1
Wander/Jitter at 3200 Hz Bandwidth
(BWSEL[1:0] = 01 and BWBOOST = 1; FXDDELAY = 1)
Jitter Tolerance (see figure 7)
f = 32 Hz
500
50
5
—
—
—
—
ns
ns
ns
ps
ps
f = 320 Hz
f = 3200 Hz
—
—
CLKOUT RMS Jitter Generation
FEC[2:0] = 000
JGEN(RMS)
JGEN(PP)
FBW
12 kHz to 20 MHz,
50 kHz to 80 MHz,
12 kHz to 20 MHz,
50 kHz to 80 MHz,
BW = 3200 Hz
—
—
—
—
—
0.8
0.25
6.1
3.0
3200
1.0
0.3
CLKOUT Peak-Peak Jitter Generation
FEC[2:0] = 000
10.0 ps
5.0
—
ps
Jitter Transfer Bandwidth (see Figure 6)
Hz
Notes:
1. Higher PLL bandwidth settings provide smaller clock output wander with temperature gradient.
2. For reliable device operation, temperature gradients should be limited to 10 °C/min.
3. Telcordia GR-1244-CORE requirements specify maximum phase transient slope during clock rearrangement in terms
of nanoseconds per millisecond. The equivalent ps/s unit is used here since the maximum phase transient magnitude
for the Si5321 (tPT_MTIE) never reaches one nanosecond.
Rev. 2.5
11
Si5321
Table 4. AC Characteristics (PLL Performance Characteristics) (Continued)
(VDD33 = 3.3 V ±5%, TA = –20 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ Max Unit
Wander/Jitter Transfer Peaking
Wander/Jitter at 3200 Hz Bandwidth
JP
< 3200 Hz
—
0.05
0.1
dB
(BWSEL[1:0] = 00 and BWBOOST= 0; FXDDELAY = 1)
Jitter Tolerance (see Figure 7)
JTOL(PP)
f = 32 Hz
1000
100
10
—
—
—
—
—
ns
ns
ns
ps
ps
ps
f = 320 Hz
f = 3200 Hz
—
—
CLKOUT RMS Jitter Generation
FEC[2:0] = 000
JGEN(RMS)
JGEN(RMS)
JGEN(PP)
JGEN(PP)
12 kHz to 20 MHz
50 kHz to 80 MHz
12 kHz to 20 MHz
50 kHz to 80 MHz
12 kHz to 20 MHz
50 kHz to 80 MHz
12 kHz to 20 MHz
50 kHz to 80 MHz
BW = 3200 Hz
< 3200 Hz
0.9
0.3
0.85
0.3
7.1
3.2
6.6
3.2
3200
0.05
1.1
0.4
1.1
—
CLKOUT RMS Jitter Generation
FEC[2:0] = 001, 010, 100,101, 110, 111
—
—
0.49 ps
10.0 ps
CLKOUT Peak-Peak Jitter Generation
FEC[2:0] = 000
—
—
5.0
ps
CLKOUT Peak-Peak Jitter Generation
FEC[2:0] = 001, 010, 100,101, 110, 111
—
11.0 ps
—
5.5
—
ps
Hz
dB
Jitter Transfer Bandwidth (see Figure 6)
Wander/Jitter Transfer Peaking
FBW
JP
—
—
0.1
Wander/Jitter at 6400 Hz Bandwidth
(BWSEL[1:0] = 00 and BWBOOST = 1; FXDDELAY = 1)
Jitter Tolerance (see Figure 7)
f = 64 Hz
f = 640 Hz
500
50
5
—
—
—
—
—
—
ns
ns
ns
f = 6400 Hz
CLKOUT RMS Jitter Generation
FEC[2:0] = 000
JGEN(RMS)
12 kHz to 20 MHz
50 kHz to 80 MHz
12 kHz to 20 MHz
50 kHz to 80 MHz
BW = 6400 Hz
< 6400 Hz
—
—
—
—
—
—
0.75 0.95 ps
0.27 0.35 ps
CLKOUT Peak-Peak Jitter Generation
FEC[2:0] = 000
JGEN(PP)
6.1
3.1
10.0 ps
5.0
—
ps
Hz
dB
Jitter Transfer Bandwidth (see Figure 6)
Wander/Jitter Transfer Peaking
Notes:
FBW
JP
6400
0.05
0.1
1. Higher PLL bandwidth settings provide smaller clock output wander with temperature gradient.
2. For reliable device operation, temperature gradients should be limited to 10 °C/min.
3. Telcordia GR-1244-CORE requirements specify maximum phase transient slope during clock rearrangement in terms
of nanoseconds per millisecond. The equivalent ps/s unit is used here since the maximum phase transient magnitude
for the Si5321 (tPT_MTIE) never reaches one nanosecond.
12
Rev. 2.5
Si5321
Table 4. AC Characteristics (PLL Performance Characteristics) (Continued)
(VDD33 = 3.3 V ±5%, TA = –20 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ Max Unit
Wander/Jitter at 6400 Hz Bandwidth
(BWSEL[1:0] = 11 and BWBOOST = 0; FXDDELAY = 1)
Jitter Tolerance (see Figure 7)
JTOL(PP)
f = 64 Hz
1000
100
10
—
—
—
—
ns
ns
ns
ps
ps
ps
ps
f = 640 Hz
f = 6400 Hz
—
—
CLKOUT RMS Jitter Generation
FEC[2:0] = 000
JGEN(RMS)
12 kHz to 20 MHz
50 kHz to 80 MHz
12 kHz to 20 MHz
50 kHz to 80 MHz
—
1.0
0.4
1.0
.45
1.3
.55
1.5
0.7
—
CLKOUT RMS Jitter Generation
FEC[2:0] = 001, 010, 100,101, 110, 111
JGEN(RMS)
—
—
CLKOUT Peak-Peak Jitter Generation
FEC[2:0] = 000
JGEN(PP)
12 kHz to 20 MHz
50 kHz to 80 MHz
12 kHz to 20 MHz
50 kHz to 80 MHz
BW = 6400 Hz
—
—
—
—
—
—
9.3
4.1
13.0 ps
6.0 ps
20.0 ps
CLKOUT Peak-Peak Jitter Generation
FEC[2:0] = 001, 010, 100,101, 110, 111
JGEN(PP)
8.0
4.0
7.5
—
ps
Hz
dB
Jitter Transfer Bandwidth (see Figure 6)
Wander/Jitter Transfer Peaking
FBW
JP
6400
0.05
< 6400 Hz
0.1
Wander/Jitter at 12800 Hz Bandwidth
(BWSEL[1:0] = 11 and BWBOOST = 1; FXDDELAY = 1)
Jitter Tolerance (see Figure 7)
f = 128 Hz
f = 1280 Hz
500
50
5
—
—
—
—
ns
ns
ns
ps
ps
f = 12800 Hz
—
—
CLKOUT RMS Jitter Generation
FEC[2:0] = 000
JGEN(RMS)
12 kHz to 20 MHz
50 kHz to 80 MHz
12 kHz to 20 MHz
50 kHz to 80 MHz
BW = 12,800 Hz
< 12,800 Hz
—
—
—
—
—
—
—
.85
1.2
.55
.35
CLKOUT Peak-Peak Jitter Generation
FEC[2:0] = 000
JGEN(PP)
6.8
11.0 ps
3.4
5.5
—
.1
ps
Hz
dB
Jitter Transfer Bandwidth (see Figure 6)
Wander/Jitter Transfer Peaking
Acquisition Time
FBW
JP
12800
0.05
300
TAQ
RSTN/CAL high to
350 ms
CAL_ACTV low, with valid
clock input and VALTIME = 0
Notes:
1. Higher PLL bandwidth settings provide smaller clock output wander with temperature gradient.
2. For reliable device operation, temperature gradients should be limited to 10 °C/min.
3. Telcordia GR-1244-CORE requirements specify maximum phase transient slope during clock rearrangement in terms
of nanoseconds per millisecond. The equivalent ps/s unit is used here since the maximum phase transient magnitude
for the Si5321 (tPT_MTIE) never reaches one nanosecond.
Rev. 2.5
13
Si5321
Table 4. AC Characteristics (PLL Performance Characteristics) (Continued)
(VDD33 = 3.3 V ±5%, TA = –20 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ Max Unit
Clock Output Wander with
Temperature Gradient 1,2
CCO_TG
Stable Input Clock;
Temperature
Gradient <10 C/min;
800 Hz Loop BW
—
—
45
ps/
C/
min
Initial Frequency Accuracy in Digital Hold CDH_FA
Mode (first 100 ms with voltage and
temperature held constant)
Stable Input Clock
Selected until entering
Digital Hold
—
—
5.5 ppm
Clock Output Frequency Accuracy Over
Temperature in Digital Hold Mode
CDH_T
Constant Supply Voltage
—
—
17.2
—
30 ppm
/C
Clock Output Frequency Accuracy Over CDH_V33
Supply Voltage in Digital Hold Mode
Constant Temperature
600 ppm
/V
Clock Output Phase Step3(See Figure 8) tPT_MTIE
When hitlessly recovering
from Digital Hold mode
–200
0
200 ps
Clock Output Phase Step Slope3
(See Figure 8)
mPT
When hitlessly recovering
from Digital Hold mode
BWSEL[1:0] = 11, BWBOOST = 0
BWSEL[1:0] = 00, BWBOOST = 0
BWSEL[1:0] = 01, BWBOOST = 0
BWSEL[1:0] = 10, BWBOOST = 0
—
—
—
—
—
—
—
—
10
5
2.5
1.25
ps/
µs
6400 Hz, No Scaling
3200 Hz, No Scaling
1600 Hz, No Scaling
800 Hz, No Scaling
Notes:
1. Higher PLL bandwidth settings provide smaller clock output wander with temperature gradient.
2. For reliable device operation, temperature gradients should be limited to 10 °C/min.
3. Telcordia GR-1244-CORE requirements specify maximum phase transient slope during clock rearrangement in terms
of nanoseconds per millisecond. The equivalent ps/s unit is used here since the maximum phase transient magnitude
for the Si5321 (tPT_MTIE) never reaches one nanosecond.
14
Rev. 2.5
Si5321
Table 5. Absolute Maximum Ratings
Parameter
Symbol
VDD33
VDIG
Value
–0.5 to 3.6
–0.3 to (VDD33 + 0.3)
±50
Unit
V
3.3 V DC Supply Voltage
LVTTL Input Voltage
V
Maximum Current any output PIN
Operating Junction Temperature
Storage Temperature Range
ESD HBM Tolerance (100 pf, 1.5 k)
mA
°C
°C
kV
TJCT
TSTG
–55 to 150
–55 to 150
1.0
Note: Permanent device damage may occur if the Absolute Maximum Ratings are exceeded. Functional operation should be
restricted to the conditions as specified in the operational sections of this data sheet. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
Table 6. Thermal Characteristics
Parameter
Symbol
Test Condition
Value
Unit
Thermal Resistance Junction to Ambient
Still Air
34.7
°C/W
JA
0
-20
-40
-60
-80
-100
-120
-140
-160
101
103
104
105
106
107
108
102
Offset Frequency
Figure 4. Typical Si5321 Phase Noise (CLKIN = 155.52 MHz, CLKOUT = 622.08 MHz, and
Loop BW = 800 Hz)
Rev. 2.5
15
Si5321
3.3 V Supply
Ferrite Bead
0.1F
2200 pF
22 pF
10 k1%
33 F
Calibration Active
Status Output
0.1F
100
CAL_ACTV
CLKIN+
0.1 F
Input Clock Source
CLKOUT+
CLKOUT–
CLKIN–
Clock Output
0.1 F
Input Clock Frequency Select
0.1 F
INFRQSEL[2:0]
Clock Output
FRQSEL[2:0]
Frequency Select
Si5321
FEC Scaling Select
PLL Bandwidth Select
FEC[2:0]
BWSEL[1:0]
BWBOOST
PLL Bandwidth Multiplier
LOS Validation Time
VALTIME
Loss of Signal (LOS)
Digital Hold Active
LOS
PWRDN/CAL
FXDDELAY
Powerdown Control
DH_ACTV
Fixed Delay Mode Control
Figure 5. Si5321 Typical Application Circuit (3.3 V Supply)
16
Rev. 2.5
Si5321
controlled oscillator (VCO). The technology produces
low phase noise clocks with less jitter than is generated
2. Functional Description
The Si5321 is a high-performance precision clock using traditional methods. See Figure 4 for an example
multiplication and clock generation device. This device phase noise plot. In addition, because external loop
accepts a clock input in the 19, 39, 78, 155, 311, or filter components are not required, sensitive noise entry
622 MHz range, attenuates significant amounts of jitter, points are eliminated thus making the DSPLL less
and multiplies the input clock frequency to generate a susceptible to board-level noise sources. This digital
clock output in the 19, 39, 78, 155, 311, 622, 1250, or technology also provides highly-stable and consistent
2500 MHz range. Additional forward or reverse clock operation over all process, temperature, and voltage
rate scaling by a factor of 255/238, 255/237, or 66/64 is variations. The benefits are smaller, lower power,
provided. This allows systems to easily provide clocks cleaner, reliable, and easy-to-use clock circuits.
that are scaled for forward error correction (FEC) rates.
2.1.1. Selectable Loop Filter Bandwidth
The 255/238 and 255/237 factors support the ITU-T
The digital characteristics of the DSPLL loop filter allow
G.709 requirements for optical transport unit (OTU) OC-
control of the loop filter parameters without the need to
48 and OC-192 rates. The 66/64 factor allows
change external components. The Si5321 provides the
conversion between XSBI and 10 GbE Base R rates.
user with up to eight user-selectable loop bandwidth
Typical applications for the Si5321 in SONET/SDH
settings for different system requirements. The base
systems are generation and/or cleaning of 19.44, 38.88,
loop bandwidth is selected using the BWSEL[1:0] pins
77.76, 155.52, 311.04, 622.08, 1244.16, or
along with BWBOOST = 0 pins. When the BWBOOST
2488.32 MHz clocks from 19.44, 38.88, 77.76, 155.52,
is driven high, the bandwidth selected on the
311.04, or 622.08 MHz clock sources.
The Si5321 employs Silicon Laboratories DSPLL®
BWSEL[1:0] pins is doubled. (See Table 7.)
When the BWBOOST pin is asserted, the Si5321 shows
technology to provide excellent jitter performance while
improved jitter generation performance. The BWBOOST
minimizing the external component count and
function is defined only when hitless recovery and FEC
maximizing flexibility and ease of use. The Si5321
scaling are disabled. Therefore, when BWBOOST is
DSPLL phase locks to the input clock signal, attenuates
high, the user must also drive FXDDELAY high and
jitter, and multiplies the clock frequency to generate the
FEC[1:0] to 000 for proper operation.
device’s SONET/SDH-compliant clock output. The
2.2. Clock Input and Output Rate Selection
DSPLL loop bandwidth is user selectable, allowing
Si5321 jitter performance optimization for different
applications. The Si5321 can produce a clock output
with jitter generation as low as 0.3 psRMS (see Table 4
on page 10), making the device an ideal solution for
clock multiplication in SONET/SDH (including OC-48,
OC-192, and OC768), Gigabit Ethernet, and 10 GbE
systems.
The Si5321 provides a 1/32x, 1/16x, 1/8x, 1/4x, 1/2x,
1x, 2x, 4x, 8x, 16x, 32x, 64x, or 128x clock frequency
multiplication function with an option for additional
frequency scaling by a factor of 255/238, 238/255, 255/
237, 237/255, 66/64, or 64/66 for FEC rate compatibility.
Output rates vary in accordance with the input clock
rate. The multiplication factor is configured by selecting
The Si5321 monitors the clock input signal for loss-of- the input and output clock frequency ranges for the
signal and provides a loss-of-signal (LOS) alarm when it device.
detects missing pulses. The Si5321 provides a digital
The Si5321 accepts an input clock in the 19, 38, 77,
hold capability that allows the device to continue
155, 311, or 622 MHz frequency range. The input
generation of a stable output clock when the input
frequency range is selected using the INFRQSEL[2:0]
reference is lost.
pins. The INFRQSEL[2:0] settings and associated
output clock rates are listed in Table 8.
®
2.1. DSPLL
The Si5321’s DSPLL phase locks to the clock input
signal to generate an internal VCO frequency that is a
multiple of the input clock frequency. The internal VCO
frequency is divided down to produce a clock output in
the 19, 39, 78, 155, 311, 622, 1250, or 2500 MHz
frequency range. The clock output range is selected
using the frequency select (FRQSEL[2:0]) pins. The
FRQSEL[2:0] settings and associated output clock rates
are given in Table 9.
The Si5321’s phase-locked loop (PLL) uses Silicon
Laboratories' DSPLL technology to eliminate jitter,
noise, and the need for external loop filter components
found in traditional PLL implementations. This is
achieved by using a digital signal processing (DSP)
algorithm to replace the loop filter commonly found in
analog PLL designs. This algorithm processes the
phase detector error term and generates a digital
control value to adjust the frequency of the voltage-
Rev. 2.5
17
Si5321
The Si5321 clock input frequencies are variable within
the range specified in Table 3 on page 7. The output
rates are scaled accordingly. If a 19.44 MHz input clock
is used, the clock output frequency is 19.44, 38.88,
77.76, 155.52 MHz, etc.
Table 8. Nominal Clock Input Frequencies
INFRQSEL2 INFRQSEL1 INFRQSEL0
Input Clock
Frequency
Range
Reserved
622 MHz
311 MHz
155 MHz
77 MHz
1
1
1
1
0
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
Table 7. Loop Bandwidth and FEC Settings
External Inputs
BWSEL
Effective
FEC
Conversion Bandwidth
Effective
PLL
FEC
[2:0]
BWBOOST
[1:0]
Rate
(Hz)
3200
3200
3200
—
38 MHz
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
00
00
00
00
00
00
00
00
10
10
10
10
10
10
10
10
11
11
11
11
11
11
11
11
00
10
11
01
01
01
01
01
01
01
01
01
000
001
010
011
100
101
110
111
000
001
010
011
100
101
110
111
000
001
010
011
100
101
110
111
0xx
0xx
0xx
0xx
000
001
010
011
100
101
110
111
1/1
19 MHz
255/238
238/255
Reserved
255/237
237/255
66/64
Reserved
3200
3200
3200
3200
800
Table 9. Nominal Clock Output Frequencies
FRQSEL2
FRQSEL1
FRQSEL0
Output Clock
Frequency
Range
64/66
1/1
2,488.32 MHz
1244.16 MHz
622.08 MHz
311.04 MHz
155.52 MHz
77.76 MHz
1
1
0
1
0
1
0
0
1
1
1
0
1
0
0
0
1
0
1
1
0
0
0
1
255/238
238/255
Reserved
255/237
237/255
66/64
800
800
—
800
800
800
64/66
800
38.88 MHz
1/1
6400
6400
6400
—
19.44 MHz
255/238
238/255
Reserved
255/237
237/255
66/64
2.2.1. FEC Rate Conversion
The Si5321 provides a 1/32x, 1/16x, 1/8x, 1/4x, 1/2x,
1x, 2x, 4x, 8x, 16x, 32x, 64x, or 128x clock frequency
multiplication function with an option for additional
forward or reverse frequency scaling by a factor of 255/
238 (15/14), 255/237 (85/79), or 66/64 (33/32) for FEC
rate conversion applications. The 255/237 and the 66/
64 rate conversions requires the input clock rate to be in
the 155 MHz or higher ranges. The multiplication factor
is configured by selecting the input and output clock
frequency ranges for the device. The additional
frequency scaling for FEC rate conversion is selected
using the FEC[2:0] control inputs.
6400
6400
6400
6400
6400
1600
12800
3200
1600
1600
1600
—
64/66
1/1
1/1
1/1
1/1
1/1
255/238
238/255
Reserved
255/237
237/255
66/64
For example, a 622.08 MHz output clock (a non-FEC
rate) can be generated from a 19.44 MHz input clock (a
non-FEC rate) by setting INFRQSEL[2:0] = 001
(19.44 MHz range), setting FRQSEL[2:0] = 011 (32x
multiplication) and setting FEC[2:0] = 000 (no FEC
scaling). A 666.51 MHz output clock (an FEC rate) can
be generated from a 19.44 MHz input clock (a non-FEC
rate) by setting INFRQSEL[2:0] = 001 (19.44 MHz
range), setting FRQSEL[2:0] = 011 (32x multiplication)
1600
1600
1600
1600
64/66
18
Rev. 2.5
Si5321
.
and setting FEC[2:0] = 001 (255/238 FEC scaling).
Jitter
Transfer
Finally, a 622.08 MHz output clock (a non-FEC rate) can
be generated from a 20.83 MHz input clock (an FEC
rate) by setting INFRQSEL[2:0] = 001 (19.44 MHz
range), setting FRQSEL[2:0] = 011 (32x multiplication)
and setting FEC[2:0] = 010 (238/255 FEC scaling).
Jitter Out
Jitter In
(s)
0 dB
Peaking
Jp
–20 dB/dec.
2.3. PLL Performance
The Si5321 PLL provides extremely low jitter
generation, high jitter tolerance, and a well-controlled
jitter transfer function with low peaking and a high
degree of jitter attenuation.
fJitter
FBW
Figure 6. PLL Jitter Transfer Mask/Template
2.3.1. Jitter Generation
2.3.3. Jitter Tolerance
Jitter generation is defined as the amount of jitter
produced at the output of the device with a jitter free
input clock. Generated jitter arises from sources within
the VCO and other PLL components. Jitter generation is
a function of the PLL bandwidth setting. Higher loop
bandwidth settings may result in lower jitter generation
but may also result in less attenuation of jitter than
might be present on the input clock signal.
Jitter tolerance for the Si5321 is defined as the
maximum peak-to-peak sinusoidal jitter that can be
present on the incoming clock. The tolerance is a
function of the jitter frequency because tolerance
improves for lower input jitter frequency.
Input
Jitter
Amplitude
2.3.2. Jitter Transfer
Excessive Input Jitter Range
–20 dB/dec.
Jitter transfer is defined as the ratio of output signal jitter
to input signal jitter for a specified jitter frequency. The
jitter transfer characteristic determines the amount of
input clock jitter that passes to the outputs. The DSPLL
technology used in the Si5321 provides tightly-
controlled jitter transfer curves because the PLL gain
parameters are determined by digital circuits that do not
vary over supply voltage, process, and temperature. In
a system application, a well-controlled transfer curve
minimizes the output clock jitter variation from board to
board and provides more consistent system level jitter
performance.
10 ns
FBW
fJitter In
Figure 7. Jitter Tolerance Mask/Template
2.4. Loss-of-Signal Alarm
The Si5321 has loss-of-signal (LOS) circuitry that
constantly monitors the CLKIN input clock for missing
pulses. The LOS circuitry sets a LOS output alarm
signal when missing pulses are detected.
The jitter transfer characteristic is a function of the
BWSEL[1:0] setting. Lower bandwidth settings result in
more jitter attenuation of the incoming clock but may
result in higher jitter generation. Table 4 on page 10
gives the 3 dB bandwidth and peaking values for
specified BWSEL settings. Figure 6 shows the jitter
transfer curve mask.
The LOS circuitry operates as follows. Regardless of
the selected input clock frequency range, the LOS
circuitry divides down the input clock into the 19 MHz
range. The LOS circuitry then over-samples this divided
down input clock to search for extended periods of time
without input clock transitions. If the LOS circuitry
detects four consecutive samples of the divided down
input clock that are the same state (i.e., 1111 or 0000), a
LOS condition is declared; the Si5321 goes into digital
hold mode, and the LOS output alarm signal is set high.
The LOS sampling circuitry runs at a frequency of fO_78
,
where fO_78 is the output clock frequency when the
FRQSEL[2:0] pins are set to 100. Figure 3 on page 5
and Table 3 on page 7 list the minimum and maximum
transitionless time periods required for declaring a LOS
on the input clock (tLOS).
Rev. 2.5
19
Si5321
Once the LOS alarm is asserted, it is held high until the
input clock is validated over a time period designated by
the VALTIME pin. When VALTIME is low, the validation
time period is about 1 ms. When VALTIME is high, the
validation time period is about 100 ms. If another LOS
condition is detected on the input clock during the
validation time (i.e., if another set of 1111 or 0000
samples are detected), the LOS alarm remains asserted
and the validation time starts over. When the LOS alarm
is finally released, the Si5321 exits digital hold mode
and locks to the input clock. The LOS alarm is
automatically set high at power-on and at every low-to-
high transition of the RSTN/CAL pin. In these cases, the
Si5321 undergoes a self-calibration before releasing the
LOS alarm and locking to the input clock.
mPT
tPT_MTIE
Recovery from digital hold
Figure 8. Recovery from Digital Hold
2.7. Reset
The Si5321 provides a Reset/Calibration pin (RSTN/
CAL) that resets the device and disables all of the
device outputs. When the RSTN/CAL pin is driven low,
the internal circuitry enters reset mode and all LVTTL
outputs are forced into a high-impedance state. Also,
the CLKOUT+ and CLKOUT– pins are connected to
VDD25 through 100 on-chip resistors. This feature is
useful for applications that employ redundant clock
sources and for in-circuit test applications. A low-to-high
transition on RSTN/CAL initializes all digital logic to a
known condition and initiates self-calibration of the
DSPLL. At the completion of self-calibration, the DSPLL
begins to lock to the clock input signal.
The Si5321 also provides an output indicating the digital
hold status of the device, DH_ACTV. The Si5321 only
enters the digital hold mode upon the loss of the input
clock. When this occurs, the LOS alarm will also be
active. Therefore, applications that require monitoring of
the status of the Si5321 need only monitor the
CAL_ACTV and either the LOS or DH_ACTV outputs to
know the state of the device.
2.5. Digital Hold of the PLL
When no valid input clock is available, the Si5321
digitally holds the internal oscillator to its last frequency
value. This provides a stable clock to the system until an
input clock is valid again. This clock maintains stable
operation in the presence of constant voltage and
temperature. The frequency accuracy specifications for
digital hold mode are given in Table 4 on page 10.
2.8. PLL Self-Calibration
The Si5321 achieves optimal jitter performance by
using self-calibration circuitry to set the VCO center
frequency and loop gain parameters within the DSPLL.
Internal circuitry generates self calibration automatically
on powerup or after a loss-of-power condition. Self-
calibration also can be manually initiated by a low-to-
high transition on the RSTN/CAL input.
2.6. Hitless Recovery from Digital Hold
When the Si5321 device is locked to a valid input clock,
a loss of the input clock switches the device to digital
hold mode. When the input clock signal returns, the
device performs a hitless transition from digital hold
mode back to the selected input clock. That is, the
device executes “phase build-out” to absorb the phase
difference between the internal VCO clock operating in
digital hold mode and the new/returned input clock. The
maximum phase step seen at the clock output during
this transition, and the maximum slope of this step, is
specified in Table 4 on page 10.
A self-calibration should be initiated after changing the
state of the FEC[2:0] inputs. Whether manually initiated
or automatically initiated at powerup, the self-calibration
process requires the presence of a valid input clock.
If the self-calibration is initiated without a valid input
clock, the device waits for a valid input clock before
executing the self-calibration. The Si5321 does not
provide an output clock while waiting for a valid input
clock or while executing its self-calibration. When the
input clock is validated, the calibration procedure
executes to completion; the device locks to the input
clock, and the output clock turns on. Subsequent losses
of the input clock do not require self-calibration. If the
input clock is lost following self-calibration, the device
enters digital hold mode with the output clock frequency
held to its last value before the LOS condition was
Asserting the Fixed Delay (FXDDELAY) pin disables
this feature and the output clock phase and frequency
locks with a known phase relationship to the input clock.
Consequently, abrupt phase change on the input clock
propagates through the device and the output slews at
the loop bandwidth until the phase relationship is
restored.
20
Rev. 2.5
Si5321
detected. When the input clock returns and is validated,
the device exits digital hold mode by re-locking to the
input clock without executing another self-calibration.
2.12. Power Supply Connections
The Si5321 incorporates an on-chip voltage regulator to
power the device from a 3.3 V supply. The voltage
regulator requires an external compensation circuit of
one resistor and one capacitor to ensure stability over
all operating conditions.
2.9. Bias Generation Circuitry
The Si5321 makes use of an external resistor to set
internal bias currents. The external resistor allows
precise generation of bias currents, which significantly
reduces power consumption and variation as compared
with traditional implementations that use an internal
resistor. The bias generation circuitry requires a 10 k
(1%) resistor connected between REXT and GND.
Internally, the Si5321 VDD33 pins are connected to the
on-chip voltage regulator input and to the device’s
LVTTL I/O circuitry. The VDD25 pins supply power to the
core DSPLL circuitry, and are also used for connection
of the external compensation circuit.
The regulator’s compensation circuit is a resistor and a
capacitor in series between the VDD25 node and ground.
2.10. Differential Input Circuitry
The Si5321 provides a differential input for the clock Typically, the resistor is incorporated into the capacitor’s
input, CLKIN. This input is internally-biased to a voltage equivalent series resistance (ESR). The target RC time
of VICM (see Table 2 on page 6) and may be driven by a constant for this combination is 15 to 50 s. The
differential or single-ended driver circuit. For capacitor used in the Si5321 evaluation board is a 33 f
transmission line termination, the termination resistor is tantalum capacitor with an ESR of 0.8 . This gives an
connected externally as shown.
RC time constant of 26.4 s. The Venkel part number
TA6R3TCR336KBR is an example of a capacitor that
meets these specifications. (See Figure 5.)
2.11. Differential Output Circuitry
The Si5321 utilizes a current mode logic (CML)
architecture to drive the differential clock output,
CLKOUT.
To get optimal performance from the Si5321 device, the
power supply noise spectrum must comply with the plot
in Figure 9. This plot shows the power supply noise
For single-ended output operation simply connect to tolerance mask for the Si5321. The customer should
either CLKOUT+ or CLKOUT– and leave the unused provide a 3.3 V supply that does not have noise density
signal unconnected.
in excess of the amount shown in the diagram.
However, the diagram cannot be used as spur criteria
for a power supply that contains single tone noise.
( /
Vn V Hz
)
2100
42
f
100 Mhz
10 kHz
500 kHz
Figure 9. Power Supply Noise Tolerance Mask
Rev. 2.5
21
Si5321
2.13. Design and Layout Guidelines
Precision clock circuits are susceptible to board noise
and EMI. To take precautions against unacceptable
levels of board noise and EMI affecting performance of
the Si5321, consider the following:
Power the device from 3.3 V since the internal
regulator provides >40 dB of isolation to the VDD25
pins (which power the PLL circuitry).
When powering the device from 3.3 V, use an
isolated, local plane to connect the VDD25 pins.
Avoid running signal traces over or below this plane
without a ground plane in between.
Route all I/O traces between ground planes as much
as possible
Maintain an input clock amplitude in the 200 mVPP to
500 mVPP differential range.
Excessive high-frequency harmonics of the input
clock should be minimized. The use of filters on the
input clock signal can be used to remove high-
frequency harmonics.
22
Rev. 2.5
Si5321
3. Pin Descriptions: Si5321
8
7
6
5
4
3
2
1
Rsvd_NC
Rsvd_NC
Rsvd_NC
Rsvd_NC
Rsvd_NC
FEC[0]
FEC[1]
A
B
C
D
E
F
Rsvd_NC
Rsvd_GND
Rsvd_GND
Rsvd_NC
GND
FXDDELAY
FRQSEL[2]
FEC[2]
BWSEL[0]
BWSEL[1]
Rsvd_GND
GND
GND
GND
GND
VSEL33
DH_ACTV
CAL_ACTV
LOS
VDD25
VDD25
VDD25
VDD25
VDD25
VDD25
VDD33
VDD33
VDD25
VDD33
VDD33
VDD25
VDD33
VDD33
VDD25
BWBOOST
CLKIN+
CLKIN–
GND
GND
INFRQSEL[0]
G
H
GND
GND
GND
GND
GND
GND
GND
INFRQSEL[1]
INFRQSEL[2]
REXT
FRQSEL[1]
CLKOUT–
CLKOUT+
FRQSEL[0]
VALTIME
RSTN/CAL
Bottom View
Figure 10. Si5321 Pin Configuration (Bottom View)
Rev. 2.5
23
Si5321
1
2
3
4
5
6
7
8
FEC[1]
FEC[0]
Rsvd_NC
Rsvd_NC
Rsvd_NC
Rsvd_NC
Rsvd_NC
A
B
C
D
E
F
BWSEL[0]
BWSEL[1]
FEC[2]
FRQSEL[2]
FXDDELAY
Rsvd_NC
GND
Rsvd_GND
Rsvd_GND
Rsvd_NC
VSEL33
GND
GND
GND
GND
Rsvd_GND
CLKIN+
CLKIN–
BWBOOST
VDD33
VDD33
VDD25
VDD33
VDD33
VDD25
VDD33
VDD33
VDD25
VDD25
VDD25
VDD25
VDD25
VDD25
VDD25
DH_ACTV
CAL_ACTV
LOS
GND
INFRQSEL[0]
GND
G
H
INFRQSEL[1]
INFRQSEL[2]
GND
GND
GND
GND
GND
GND
GND
REXT
RSTN/CAL
VALTIME
FRQSEL[0]
CLKOUT+
CLKOUT–
FRQSEL[1]
Top View
Figure 11. Si5321 Pin Configuration (Transparent Top View)
24
Rev. 2.5
Si5321
Table 10. Si5321 Pin Descriptions
Pin #
Pin Name
I/O
Signal Level
Description
System Clock Input.
D1
E1
CLKIN+
CLKIN–
I
AC Coupled
200–500 mVPPD
(See Table 2)
Clock input to the DSPLL circuitry. The frequency of
the CLKIN signal is multiplied by the DSPLL to gen-
erate the CLKOUT clock output. The input-to-output
frequency multiplication factor is set by selecting the
clock input range and the clock output range. The
frequency of the CLKIN clock input can be in the 19,
38, 77, 155, 311, or 622 MHz range (nominally
19.44, 38.88, 77.76, 155.52, 311.04, or
622.08 MHz) as indicated in Table 3 on page 7. The
clock input frequency is selected using the INFRQ-
SEL[2:0] pins. The clock output frequency is
selected using the FRQSEL[1:0] pins. An additional
scaling factor may be selected for FEC operation
using the FEC[2:0] control pins.
F1
G1
H1
INFRQSEL[0]
INFRQSEL[1]
INFRQSEL[2]
I*
LVTTL*
Input Frequency Range Select.
Pins(INFRQSEL[2:0]) select the frequency range for
the input clock, CLKIN. (See Table 3 on page 7.)
000 = Reserved.
001 = 19 MHz range.
010 = 38 MHz range.
011 = 77 MHz range.
100 = 155 MHz range.
101 = 311 MHz range.
110 = 622 MHz range.
111 = Reserved.
H6
H7
CLKOUT+
CLKOUT–
O
CML
Differential Clock Output.
High-frequency clock output. The frequency of the
CLKOUT output is a multiple of the frequency of the
CLKIN input. The input-to-output frequency multipli-
cation factor is set by selecting the clock input range
and the clock output range. The frequency of the
CLKOUT clock output can be in the 19, 38, 77, 155,
311, 622, 1244 or 2488 MHz range as indicated in
Table 3 on page 7. The clock output frequency is
selected using the FRQSEL[2:0] pins. The clock
input frequency is selected using the INFRQ-
SEL[2:0] pins. An additional scaling factor may be
selected for FEC operation using the FEC[2:0] con-
trol pins.
*Note: The LVTTL inputs on the Si5321 device have an internal pulldown mechanism that causes the input to default to a
logic low state if the input is not driven from an external source.
Rev. 2.5
25
Si5321
Table 10. Si5321 Pin Descriptions (Continued)
Pin #
Pin Name
I/O
Signal Level
Description
H5
H8
B3
FRQSEL[0]
FRQSEL[1]
FRQSEL[2]
I*
LVTTL*
Clock Output Frequency Range Select.
Select the frequency range of the clock output, CLK-
OUT. (See Table 3 on page 7.)
001 = 19 MHz Frequency Range.
000 = 39 MHz Frequency Range.
100 = 78 MHz Frequency Range.
010 = 155 MHz Frequency Range.
101 = 311 MHz Frequency Range.
011 = 622 MHz Frequency Range.
110 = 1.25 GHz Frequency Range.
111 = 2.5 GHz Frequency Range.
A3
A2
B2
FEC[0]
FEC[1]
FEC[2]
I*
LVTTL*
FEC Selection.
Enables or disables scaling of the input-to-output
frequency multiplication factor for FEC clock rate
compatibility.
The frequency of the CLKOUT output is a multiple of
the frequency of the CLKIN input. Selecting the
clock input range, the clock output range, and the
FEC scaling factor sets the input-to-output fre-
quency multiplication factor. The clock output fre-
quency is selected using the FRQSEL[2:0] pins. The
clock input frequency is selected using the INFRQ-
SEL[2:0] pins. Scaling factors of 255/238, 238/255,
255/237, 237/255, 66/64, or 64/66 may be selected
for FEC operation using the FEC[2:0] control pins as
indicated below. Scaling factors of 255/237, 237/
255, 66/64, or 64/66 require that the input clock rate
be in the 155 MHz or higher range.
000 = No FEC scaling.
001 = 255/238 FEC scaling.
010 = 238/255 FEC scaling.
011 = Reserved.
100 = 255/237 FEC scaling (155 MHz or higher
input clock range required).
101 = 237/255 FEC scaling (155 MHz or higher
input clock range required).
110 = 66/64 FEC scaling (155 MHz or higher input
clock range required).
111 = 64/66 FEC scaling (155 MHz or higher input
clock range required).
*Note: The LVTTL inputs on the Si5321 device have an internal pulldown mechanism that causes the input to default to a
logic low state if the input is not driven from an external source.
26
Rev. 2.5
Si5321
Table 10. Si5321 Pin Descriptions (Continued)
Pin #
Pin Name
I/O
Signal Level
Description
B1
C1
BWSEL[0]
BWSEL[1]
I*
LVTTL*
Bandwidth Select.
BWSEL[1:0] pins set the bandwidth of the loop filter
within the DSPLL to 6400, 3200, 1600, or 800 Hz as
indicated below.
00 = 3200 Hz
01 = 1600 Hz
10 = 800 Hz
11 = 6400 Hz
Note: The loop filter bandwidth is twice the value
indicated here when BWBOOST is set high.
D2
B4
BWBOOST
FXDDELAY
I*
I*
LVTTL*
LVTTL*
Bandwidth Boost.
Active high input to boost the selected bandwidth
2x. When this pin is high the loop filter bandwidth
selected on BWSEL[1:0] is doubled. When this pin
is high, FXDDELAY must also be high and FEC[2:0]
must be 000.
Fixed Delay Mode.
Set high to disable hitless recovery from digital hold
mode. This configuration is useful in applications
that require a known or constant input-to-output
phase relationship.
When this pin is high, hitless switching from digital
hold mode back to a valid clock input is disabled.
When switching from digital hold mode to a valid
clock input with FXDDELAY high, the clock output
changes as necessary to re-establish the initial/
default input-to-output phase relationship that is
established after powerup or reset. The rate of
change is determined by the setting of BWSEL[1:0].
When this pin is low, hitless switching from Digital
Hold mode back to a valid clock input is enabled.
When switching from digital hold mode to a valid
clock input with FXDDELAY low, the device enables
“phase build out” to absorb the phase difference
between the clock output and the clock input so that
the phase change at the clock output is minimized.
In this case, the input-to-output phase relationship
following the transition out of digital hold mode is
determined by the phase relationship at the time
that switching occurs.
Note: FXDDELAY should remain at a static high or static
low level during normal operation. Transitions on
this pin are allowed only when the RSTN/CAL pin
is low. FXDDELAY must be set high when
BWBOOST is set high.
*Note: The LVTTL inputs on the Si5321 device have an internal pulldown mechanism that causes the input to default to a
logic low state if the input is not driven from an external source.
Rev. 2.5
27
Si5321
Table 10. Si5321 Pin Descriptions (Continued)
Pin #
Pin Name
I/O
Signal Level
Description
H4
VALTIME
I*
LVTTL*
Clock Validation Time for LOS.
VALTIME sets the clock validation times for recovery
from an LOS alarm condition. When VALTIME is
high, the validation time is approximately 100 ms.
When VALTIME is low, the validation time is approx-
imately 2 ms.
H3
RSTN/CAL
I*
LVTTL*
Reset/Calibrate.
When low, all LVTTL outputs are forced into a high
impedance state, the DSPLL is forced out-of-lock,
and the device control logic is reset.
A low-to-high transition on RSTN/CAL initializes all
digital logic to a known condition and initiates self-
calibration of the DSPLL. At the completion of self-
calibration, the DSPLL begins to lock to the selected
clock input signal and begins to drive out the output
clock signal onto the CLKOUT pins.
F8
D8
LOS
O
O
LVTTL
LVTTL
Loss-of-Signal (LOS) Alarm for CLKIN.
Active high output indicates that the Si5321 has
detected missing pulses on the input clock signal.
The LOS alarm is cleared after either 100 ms or 13 s
of a valid CLKIN clock input, depending on the set-
ting of the VALTIME input.
DH_ACTV
Digital Hold Mode Active.
Active high output indicates that the DSPLL is in
digital hold mode. Digital hold mode locks the
current state of the DSPLL and forces the DSPLL to
continue generation of the output clock with no
additional phase or frequency information from the
input clock.
E8
C2
CAL_ACTV
O
LVTTL
Calibration Mode Active.
This output is driven high during the DSPLL self-cal-
ibration and the subsequent initial lock acquisition
period.
Reserved.
VSEL33
VDD33
I*
LVTTL*
Supply
This pin must be tied to VDD33 directly for normal
operation.
3.3 V Supply.
D3–D5,
E3–E5
VDD
3.3 V power is applied to the VDD33 pins. Typical
supply bypassing/decoupling for this configuration is
indicated in the typical application diagram for 3.3 V
supply operation.
*Note: The LVTTL inputs on the Si5321 device have an internal pulldown mechanism that causes the input to default to a
logic low state if the input is not driven from an external source.
28
Rev. 2.5
Si5321
Table 10. Si5321 Pin Descriptions (Continued)
Pin #
Pin Name
I/O
Signal Level
Description
2.5 V Compensation Network.
D6, D7, E6,
E7, F3–F7
VDD25
VDD
Supply
These pins provide a means of connecting the
compensation network for the on-chip regulator.
C3–C7, E2,
F2, G2–G8
GND
GND
Supply
Analog
Ground.
Must be connected to system ground. Minimize the
ground path impedance for optimal performance of
the device.
H2
REXT
I
External Biasing Resistor.
Used by on-chip circuitry to establish bias currents
within the device. This pin must be connected to
GND through a 10 k (1%) resistor.
A4–8, B5, B8
B6, B7, C8
RSVD_NC
LVTTL
LVTTL
Reserved—No Connect.
This pin must be left unconnected for normal
operation.
RSVD_GND
Reserved—GND.
This pin must be tied to GND for normal operation.
*Note: The LVTTL inputs on the Si5321 device have an internal pulldown mechanism that causes the input to default to a
logic low state if the input is not driven from an external source.
Rev. 2.5
29
Si5321
4. Ordering Guide
Part Number
Package
Temperature Range
Si5321-G-BC
Si5321-H-BL
Si5321-H-GL
63-Ball CBGA
(Prior Revision) RoHS-5
–20 to 85 °C
63-Ball PBGA
(Current Revision) RoHS-5
–20 to 85 °C
–20 to 85 °C
63-Ball PBGA
(Current Revision) RoHS-6
30
Rev. 2.5
Si5321
5. Package Outline
Figure 12 illustrates the package details for the Si5321. Table 11 lists the values for the dimensions shown in the
illustration.
Figure 12. 63-Ball Plastic Ball Grid Array (PBGA)
Table 11. Package Diagram Dimensions (mm)
Symbol
Min
1.24
0.40
0.34
0.50
0.50
Nom
1.41
Max
1.58
0.60
0.42
0.56
0.70
Symbol
E1
Min
Nom
7.00 BSC
1.00 BSC
0.50 BSC
0.10
Max
A
A1
0.50
e
A2
0.38
S
A3
0.53
aaa
bbb
ccc
ddd
eee
b
0.60
0.10
D
9.00 BSC
9.00 BSC
7.00 BSC
0.12
E
0.15
D1
Notes:
0.08
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to JEDEC outline MO-192, variation AAB-1.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020C specification for Small Body Components.
Rev. 2.5
31
Si5321
6. 9x9 mm PBGA Card Layout
Symbol
X
Min
Nom
0.45
7.00
7.00
1.00
1.00
Max
0.40
0.50
C1
C2
E1
E2
Notes:
General
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing is per the ANSI Y14.5M-1994 specification.
3. This Land Pattern Design is based on the IPC-7351 guidelines.
Solder Mask Design
1. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to
be 60 µm minimum, all the way around the pad.
Stencil Design
1. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder
paste release.
2. The stencil thickness should be 0.125 mm (5 mils).
3. The ratio of stencil aperture to land pad size should be 1:1.
Card Assembly
1. A No-Clean, Type-3 solder paste is recommended.
2. The recommended card reflow profile is per the JEDEC/IPC J-STD-020C specification for Small Body Components.
32
Rev. 2.5
Si5321
DOCUMENT CHANGE LIST
Revision 2.0 to Revision 2.1
Updated Table 3, “AC Characteristics,” on page 7.
Updated Figure 8, “Recovery from Digital Hold,” on
page 20.
Updated Figure 12, “63-Ball Plastic Ball Grid Array
(PBGA),” on page 31.
Updated Table 11, “Package Diagram Dimensions
(mm),” on page 31.
Added Figure 4, “Typical Si5321 Phase Noise
(CLKIN = 155.52 MHz, CLKOUT = 622.08 MHz, and
Loop BW = 800 Hz),” on page 15.
Revision 2.1 to Revision 2.2
Updated Table 3, “AC Characteristics,” on page 7.
Updated Table 11, “Package Diagram Dimensions
(mm),” on page 31.
Revision 2.2 to Revision 2.3
Updated "5. Package Outline" on page 31.
Revision 2.3 to Revision 2.4
Device Revision G to H Transition.
Updated test condition for differential output voltage
swing, input clock frequency, clock output rise/fall
time, and jitter specifications.
Updated “3. Pin Descriptions: Si5321”.
Updated "4. Ordering Guide" on page 30.
Updated "5. Package Outline" on page 31.
Updated "6. 9x9 mm PBGA Card Layout" on page
32.
Revision 2.4 to Revision 2.5
Updated Table 6, “Thermal Characteristics,” on
page 15.
Rev. 2.5
33
ClockBuilder Pro
One-click access to Timing tools,
documentation, software, source
code libraries & more. Available for
Windows and iOS (CBGo only).
www.silabs.com/CBPro
Timing Portfolio
www.silabs.com/timing
SW/HW
www.silabs.com/CBPro
Quality
www.silabs.com/quality
Support and Community
community.silabs.com
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers
using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific
device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories
reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply
or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific
written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected
to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations
thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®,
USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of
ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
http://www.silabs.com
相关型号:
SI5321-H-ZL5
Support Circuit, 1-Func, PBGA63, 9 X 9 MM, ROHS COMPLIANT, PLASTIC, MO-192AAB-1, BGA-63
SILICON
©2020 ICPDF网 联系我们和版权申明