LQ057V3DG02 [SHARP]
Display,;
| 型号： | LQ057V3DG02 |
| 厂家： | 
SHARP ELECTRIONIC COMPONENTS |
| 描述： | Display, |
| 文件： | 总19页 (文件大小：1436K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
RECORDS OF REVISION
MODEL No : LQ057V3DG02
SPEC No : LD-20901A
NO. PAGE
SUMMARY
NOTE
2008.9.5
-A
－
1st Issue
LD-20901A-1
NOTICE
This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws,
no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for
any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is
also required before any use of this publication may be made by a third party.
The application circuit examples in this publication are provided to explain the representative applications of SHARP's
devices and are not intended to guarantee any circuit design or permit any industrial property right or other rights to be
executed. SHARP takes no responsibility for any problems related to any industrial property right or a third party
resulting from the use of SHARP's devices, except for those resulting directly from device manufacturing processes.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that
occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to
obtain the latest device specification sheets before using any SHARP's device.
SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and other
contents described herein at any time without notice in order to improve design or reliability. Contact SHARP in order
to obtain the latest specification sheets before using any SHARP's device. Manufacturing locations are also subject to
change without notice.
Observe the following points when using any device in this publication. SHARP takes no responsibility for damage
caused by improper use of the devices.
The devices in this publication are designed for general electronic equipment use.
The appropriate design measures should be taken to ensure reliability and safety when SHARP's devices are used for
equipment such as:
・Transportation control and safety equipment (i.e.,aircraft, trains, automobiles, etc.)
・Traffic signals・Gas leakage sensor breakers ・Alarm equipment・Various safety devices etc.
SHARP's devices shall not be used for equipment that requires extremely high level of reliability, such as:
・Military and space applications
・Nuclear power control equipment
・Medical equipment for life support
Contact a SHARP representative, in advance, when intending to use SHARP’s devices for any “specific” applications
other than those recommended by SHARP.
Contact and consult with a SHARP representative if there are any questions about the contents of this publication.
LD-20901A-2
1
2
Applicable TFT-LCD module
This specification applies to the color TFT-LCD module, LQ057V3DG02.
Overview
This module is a color active matrix transmissive LCD module incorporating amorphous silicon TFT (Thin
Film Transistor).
It is composed of a color TFT-LCD panel, driver ICs, control circuits and power supply circuitry and a
backlight unit. Graphics and texts can be displayed on a 640 x RGB x 480 dots panel with 262,144 colors by
feeding 18 bit data signal (6bit/each of R,G,B), 4(four) timing signals, +3.3V DC power supply for TFT-LCD
and AC power supply for backlight.
・
・
・
Fine images with stripe aligned 307,200 pixels on 5.7 inch diagonal screen
Color display capability of 262,144 colors with 18 bit data signal(6 bits for each RGB)
Adapting a wide viewing angle technology [best viewing angle: 12 o’clock direction]
（6 o’clock direction is also available by the function to flip the screen horizontally or vertically)
High contrast, thanks to active matrix drive system
・
・
・
・
・
・
・
AG(Anti Glare) polarizing filter
Light and slim compact module achieved by COG assemble technology
Natural coloring reproducibility by employing normally-white-mode, which has good nature in coloring
Image inversion both horizontally and vertically
LED drive circuit is built in this module to provide PWM Dimmer function.
This module has corresponded with the RoHS directive.
3
Mechanical Specifications
items
Display size (Diagonal)
Active display area
Pixel format
specifications
14.4 (5.7")
unit
cm
mm
dot
-
115.2 (H)×86.4(V)
640(H)×RGB×480(V)
(1 pixel=R+G+B dots)
Pixel pitch
0.18[H]×0.18[V]
R,G,B vertical stripe
Normally white
mm
Pixel configuration
LCD mode
-
-
Dimension
Mass
*
144 (W)×104.6 (H)×13.0(D)
250（max）
mm
g
* Protrusion such as backlight harness and positioning boss are not included.
Fig.1 shows dimensions of the module.
LD-20901A-3
4
Input Signal Assignment
4.1 TFT-LCD Panel driving section
Employed connector: IMSA-9637S-33Y902 (IRISO ELECTRONICS CO.,LTD.)
Terminal : 0.5mm pitch, bottom contact, Au plating
Pin No. Symbol
Function
Polarity
GND Ground
１
CK
Clock signal for sampling each data signal
２
Hsync Horizontal synchronous signal
Vsync Vertical synchronous signal
GND Ground
３
４
５
R0
R1
R2
R3
R4
R5
RED data signal(LSB)
RED data signal
６
７
RED data signal
８
RED data signal
９
RED data signal
１０
１１
１２
１３
１４
１５
１６
１７
１８
１９
２０
２１
２２
２３
２４
２５
２６
２７
２８
２９
RED data signal(MSB)
GND Ground
G0
G1
G2
G3
G4
G5
GREEN data signal(LSB)
GREEN data signal
GREEN data signal
GREEN data signal
GREEN data signal
GREEN data signal(MSB)
GND Ground
B0
B1
B2
B3
B4
B5
BLUE data signal(LSB)
BLUE data signal
BLUE data signal
BLUE data signal
BLUE data signal
BLUE data signal(MSB)
TEST1 TEST1(Please be sure to connect 26pin with ground)
ENAB Data enable signal (signal to settle the horizontal display position)
Vcc +3.3V power supply
【Note 1】
(Supply same voltage to 28 and 29 pin )
Vcc
R/L
Selection signal for horizontal scanning direction
(“L” : Normally , “H” : Right-and-Left reversal)
Selection signal for vertical scanning direction
(“H” : Normally , “L” : Up-and-Down reversal)
【Note 2】
【Note 2】
３０
３１
U/D
TEST2 TEST2(to be open, or connected to either GND or Vcc)
TEST3 TEST3(Please be sure to connect 33pin with ground)
３２
３３
The back shield case is internally grounded to GND of the module.
The front shield case is not certainly grounded to GND of the module.
【Note 1】
The horizontal display location is designated and controlled by rising timing of ENAB signal.
However if ENAB signal is fixed to “Low”, display location is designated by the default setting in the
module.
(Don’t use the module by fixing ENAB to “High”) …..See: Chapter 7-2
LD-20901A-4
【Note 2】
R/L = L，U/D = H
R/L = H，U/D = H
R/L = L，U/D = L
R/L = H，U/D = L
4.2 LED drive circuit section
Employed connector: SM06B-SRSS- TB(LS) (SN) (JST:1.0mm pitch)
Adapted connector: SHR-06V-S-B SHR-06V-S (JST)
・
CN2
Pin no. Symbol
Function
LED drive circuit power supply (12V)
LED drive circuit power supply (12V)
Ground
1
2
3
VLED
VLED
GND
4
5
6
GND
Ground
PWM
LEDO
PWM Dimmer
LED OPEN[ normal:High(5V), open error:Low(0V) ]
5
Absolute Maximum Ratings
Parameter
Symbol Condition
Vcc Ta=25℃
VLED Ta=25℃
Ratings
0 ~ +4.6
Unit
V
Remark
Supply voltage
-
LED drive circuit supply voltage
Input signal voltage
-0.3 ~ + 17
V
-
V
I
Ta=25℃ -0.3 ~ + Vcc+0.3
V
[Note 1]
PWM Dimmer signal voltage
Storage temperature
VPWM Ta=25℃
- 0.3 ~ +17
-30 ~ +80
-30 ~ +80
V
Tstg
-
-
[Note 2,3,4]
Operating temperature (Panel surface)
Topp
℃
[Note 1] CK, R0 ~ R5, G0 ~ G5, B0 ~ B5, Hsync, Vsync, ENAB, R/L, U/D
[Note 2] Humidity: Less than 95%RH at Ta ≤ 40°C and Maximum wet-bulb temperature must not exceed
39°C at Ta>40°C, with no condensation.
[Note 3] The operating temperature only guarantees operation of the circuit. As to contrast, speed response, and
other factors related to display quality, judgment is done using the ambient temperature Ta =＋25℃.
[Note 4]Under the environment between 65℃ and 80℃, it may cause display non-uniformity issue, etc.
[Note 5]Using condition must not exceed the rated value above at any place in the module.
LD-20901A-5
6
Electrical characteristics
6.1 TFT-LCD Panel driving section
Ta＝25℃
Remarks
Parameter
Symbol
Vcc
MIN
TYP
MAX
+3.6
-
Unit
V
Supply voltage
+3.0
+3.3
[Note1]
Current dissipation
Icc
-
220
mA
mV p-p
V
[Note2] VCC=3.3V
VCC=3.3V
V
Allowed input ripple voltage
Input voltage (“Low” state)
Input voltage (“High” state)
Input leakage current (low)
-
-
-
-
-
100
RF
V
0
0.7Vcc
-
0.3Vcc
Vcc
4.0
IL
V
V
[Note3]
VI=0V[Note4]
IH
IOL1
IOL2
IOH1
IOH2
μA
VI=0V[Note5]
-
-
-
-
-
-
μA
μA
μA
4.0
4.0
4.0
V =3.3V[Note4]
Input leakage current (High)
I
V =3.3V[Note5]
I
VCC
data
VCC
data
[Note1] Vcc turn-on/off conditions
1s < t0
0.3V
0.3V
time
t0
VCC
3.0V
Vcc-dip conditions
1) At 2.7V ≤ Vcc < 3.0V
td ≤ 10ms
2.７V
2) At Vcc < 2.7V
tｄ
Vcc dip conditions should also follow
the Vcc turn-on/off conditions
[Note2] Current dissipation (Typ.): When Black pattern is displayed.
[Note3] CK, R0~R5, G0~G5, B0~B5, Hsync, Vsync, ENAB, R/L, U/D
[Note4] R0~R5, G0~G5, B0~B5, Hsync, Vsync and ENAB
[Note5] R/L, U/D
LD-20901A-6
6-2 Vcc turn-on/off conditions
VCC:100%
VCC:100%
3.0V
0.3V
0.3V
t1
T3
t2
DCLK
Hsync,Vsync,
DATA
Signal Necessary Area
◎ Every Signal is CMOS Input, Hi-Z is prohibited when VCC is on level.
Please avoid the input of the signal voltage more than Supply voltage (VCC).
Min.
Typ.
Max.
10
50
unit
ms
ms
ms
t1
t2
t3
0
0
0
-
-
-
100
6-3 LED drive circuit section
Parameter
Symbol
MIN
TYP
MAX
12.6
-
Unit
V
Remarks
Input voltage
VLED
ILED
11.2
-
12.0
300
-
Current dissipation
Dimmer signal Low voltage
Dimmer signal High voltage
Dimmer frequency
mA
V
VLED = 12.0V
VPWM
VPWM
fPWM
L
-
0.2
12
-
H
1.4
-
5.0
120
-
V
Hz
μs
PWM Pulse width
TPWMH
10
4.6
0
-
High period
@ILEDOH = 1μA
@ILEDOL = 50μA
[Note]
LED OPEN voltage (normal)
LED OPEN voltage (error)
Life time
VLEDO
VLEDO
LL
H
5.0
-
5.4
0.3
-
V
L
V
-
50,000
Hour
PWM Dimmer function
・ PWM Dimmer function can be available by inputting PWM pulse into a PWM terminal and changing
the duty ratio of Hi/Lo.
( PWM = High : ON , PWM = Low : OFF )
・ Please do not make the PWM terminal in a floating state ( no input state).
Please be connected to the GND at the waiting time.
・ Please input PWM signal after VLED(12V) is supplied.
・ Please turn off VLED(12V) after PWM signal is stopped.
[Note]①Driving condition:
・The state of the LCD module installation: Landscape position and standing position
・Atmosphere temperature: 25℃
・VLED = 12.0V,PWM:H (Constant current drive／Continuous turning on)
②Definition of Life time:
Brightness becomes 50% of the original value .(under condition ①)
LD-20901A-7
7
Timing Characteristics of Input Signals
Timing diagrams of input signal are shown in Fig.2.
7.1 Timing Characteristics
Parameter
Frequency
“High” time
“Low” time
Setup time
Hold time
Symbol
1/Tc
Tch
Tcl
Tds
MIN.
24.3
10
TYP.
25.2
－
MAX.
26.54
－
Unit
MHz
ns
ns
ns
Note
Clock
10
－
－
5
Data
－
－
5
Tdh
ns
－
－
29.89
780
2
31.75
800
－
33.74
820
Hsync
Period
TH
μs
clock
clock
line
TH-10
530
Pulse width
Period
Pulse width
THp
TV
TVp
THd
THc
520
2
525
－
Vsync
60Hz
519
line
Horizontal display period
Phase difference between
Hsync and clock
640
－
clock
ns
－
5
－
Tc-10
Phase difference between
Hsync and Vsync
Vertical back porch
Vertical front porch
Vertical display period
TVh
0
50
clock
－
34(fixed)
480
TVs
TVf
TVd
※
6
－
16
－
line
Note) In case of lower frequency, the deterioration of display quality, flicker etc., may occur.
※TVf = TV – TVs(34) – TVd(480)
7.2 Display Position in horizontal direction
Display position in horizontal direction is designated by rising timing of ENAB signal.
Parameter
ENAB signal Setup time
Pulse width
Phase difference between Hsync and
ENAB signal
Symbol
Tes
MIN
5
TYP
－
MAX
Tc-10
Unit
ns
Note
Tep
640
－
ns
－
－
THe
44
104
clock
When ENAB is fixed to “Low”, the horizontal display will starts from the clock C104 (clock) as shown in Fig.2.
7.3 Display position in vertical direction
Display start position in vertical direction TVs is fixed to the 34th line.
8
Input Signals, Basic Display Colors and Gray Scale of Each Color.
Display position of input data
UP
D3,DH1
D640,DH1
D2,DH1
D1,DH1
D1,DH2 D2,DH2
D1,DH3
B G R
SHARP
D640,DH480
D1,DH480
TH
THp
Horizontal sync.
signal
0.7Vcc
0.3Vcc
0.3Vcc
Tc
0.3Vcc
（Hsync）
Tch
THc
Tcl
＊Only when ENAB is fixed “LOW”
0.7Vcc
Clock signal
0.3Vcc 0.3Vcc
0.3Vcc
（CK）
C104 (Number of clock)
C0＊ C1＊
Tdh
C2＊
Tds
Data (R0～5,
G0～5, B0～5）
Horizontal invalid data period
Horizontal invalid data period
D1
D2
Tes
D3
D638
D640
D639
D4 D5
THd
THe
0.7Vcc
Data Enable signal
Tep
（ENAB）
TVp
0.7Vcc
TV
Vertical Sync.
signal
0.3Vcc
0.3Vcc
TVh
（Vsync）
Horizontal sync.
signal (Hsync)
0.3Vcc
L1
L2
･･･
L33
L34
( Number of Hync )
DATA ENABLE
signal (ENAB)
TVf
TVs
TVd
Data (R0～5,
Vertical invalid
data period
Vertical invalid data period
DH1
DH2
DH3
DH479 DH480
G0～5,B0～5）
Fig 2. Input signal waveforms
LD-20901A-9
Colors &
Data signal
R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5
Gray
Scale
Gray scale
-
-
-
-
-
-
0
0
0
0
1
1
0
0
0
0
1
1
0
0
0
0
1
1
0
0
0
0
1
1
0
0
0
0
1
1
0
0
0
0
1
1
0
0
1
1
0
0
0
0
1
1
0
0
0
0
1
1
0
0
0
0
1
1
0
0
0
0
1
1
0
0
0
0
1
1
0
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Black
Blue
Green
Cyan
Red
Magenta
-
1
1
0
1
0
1
1
0
0
1
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
0
1
0
0
0
0
1
0
0
0
0
1
0
0
0
0
1
0
0
0
0
1
0
0
0
0
1
0
0
0
Yellow
White
Black
×
Darker
×
-
GS0
GS1
GS2
È
È
È
È
È
È
È
È
Ø
GS61
GS62
GS63
GS0
1
0
1
0
0
1
1
0
1
1
1
0
1
1
1
0
1
1
1
0
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Brighter
Ø
Red
Black
×
Darker
×
GS1
GS2
È
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
È
È
È
È
È
È
È
Ø
GS61
GS62
GS63
GS0
GS1
GS2
È
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
0
0
0
0
1
1
0
0
0
1
1
1
0
0
0
1
1
1
0
0
0
1
1
1
0
0
0
1
1
1
0
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Brighter
Ø
Green
Black
×
Darker
×
È
È
È
È
È
È
È
Ø
GS61
GS62
GS63
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Brighter
Ø
Blue
0: Low level voltage, 1: High level voltage
Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the
combination of total 18 bit data signals, the 262,144-color display can be achieved on the screen.
LD-20901A-10
9
Optical Specification
Parameter
Ta=25°C, Vcc=+3.3V, VLED=+12V
Symbol
Condition
Min.
-
Typ. Max.
Unit
Remark
80
Viewing angle Horizontal θ21,θ22
CR≥5
-
° (Deg.) [Note9-1,4]
° (Deg.)
-
-
80
-
Range
Vertical
θ11
θ12
70
-
° (Deg.)
Contrast ratio
CR max Best viewing
angle
200
600
-
-
[Note9-2]
[Note9-3]
[Note9-4]
Response time
Rise
Fall
Tr
Td
x
θ = 0°
-
8
20
40
-
ms
-
-
21
ms
Chromaticity of white
0.313
0.329
400
-
y
θ = 0
-
-
-
cd/m2
Luminance
Y
300
-
The optical specifications are measured 30 minute after turning on and in a dark room or equivalent
condition, according to the method shown in Fig.9-1, 2 below.
0mm~Focal distance
Sensor (BM-5A/BM-7/SR-1)
Sensor (EZ-CONTRAST)
400mm
Field=2°
Center of LCD screen
TFT LCD Module
Center of LCD screen
TFT LCD Module
Fig.9-2 Measuring setup for
Luminance, Chromaticity
Fig.9-1 Measuring setup for
Viewing angle and Contrast ratio
and Response time
(BM-5A is used for contrast.)
(BM-7 is used for Luminance, SR-1 is for response)
LD-20901A-11
[Note9-1] Definitions of viewing angle range:
The best viewing angle of this module is slightly leaned to 12 o’clock from normal line (θ11direction in the figure
above).
Where θ11＞θmax
,
gray scale is reversed partially.
Where θ11＜θmax, or in θ12 direction, gray scale isn’t reversed.
[Note9-2] Definition of contrast ratio:
The contrast ratio is defined as the following.
Central luminance(brightness) with all pixels white
Central luminance(brightness) with all pixels black
Contrast Ratio (CR) ＝
[Note9-3] Definition of response time:
The response time is defined as the following figure and shall be measured by
switching the input signal between "black" and "white" alternatively.
[Note9-4] This parameter should be measured at the center of the screen and 30 minutes after turn-on.
The characteristics are measured when the driver circuit is not powered (normally white).
LD-20901A-12
10 Display Qualities
Please refer to the Outgoing Inspection Standard.
11 Handling Instruction
a) Be sure to turn off the power supply when inserting or disconnecting the cable.
b)Our TFT-LCD module is designed to be fixed to the hardware with mounting holes on 4-corners on the
backside. Be sure to design the cabinet so that the module can be installed without any extra stress such
as warp or twist.
c) Since the front polarizer is easily damaged, pay attention not to scratch it.
Blow away dust on the polarizer with antistatic Ｎ2 blow. It is undesirable to wipe off because a polarizer
is sensitive. It is recommended to peel off softly using the adhesive tape when soil or finger oil is stuck to
the polarizer. When unavoidable, wipe off carefully with a cloth for wiping lenses.
d) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
Handle with care.
g) Since CMOS LSI is used in this module, take care of static electricity and ensure the human earth
when handling. Observe all other precautionary requirements in handling components.
h) Since there is a circuit board in the module back, stress shall not be impressed in designing and
assembling. If stress is impressed, there arises a possibility that circuit parts may be damaged.
i) Protection film is attached to the module surface to prevent it from being scratched .
Peel the film off slowly , just before the use, with strict attention to electrostatic charges.
Blow off 'dust' on the polarizer by using an ionized nitrogen.
j) The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching
protective board over the LCD, be careful about the optical interface fringe etc. which degrades display
quality.
k) Direct sunlight on LCD panel may cause degradation of panel quality. Do not expose the LCD panel to
direct sunlight. Lightproof shade etc. should be attached when LCD panel is used under such
environment.
l) Connect GND to 4 place of mounting holes to get stable against EMI and external noise.
m) When handling LCD modules and assembling them into cabinets, please be noted that long-term
storage in the environment of oxidization or deoxidization gas and the use of such materials as
reagent, solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and
discoloration of the LCD modules.
n) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets
inside your eye or mouth by mistake.
o) Notice: Never dismantle the module , because it will cause failure.
Please don't remove the fixed tape, insulating tape etc that was pasted on the original module.
(except for protection film of the panel and the crepe tape(yellow tape) temporarily adhered on the
module.)
p) Be careful when using it for long time with fixed pattern display as it may cause afterimage.
（Please use a screen saver etc., in order to avoid an afterimage.）
q) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.
If adjusted value is changed, the specification may not be satisfied.
LD-20901A-13
r) If a minute particle get into the module and adheres on an optical material, it may cause display
irregularity issue, etc. Therefore, fine-pitch filters have to be built into cooling and inhalation hole if you
intend to install a fan.
s) Liquid crystal can be damaged by ultraviolet light. Be sure not to operate or storage under direct sunlight
or strong ultraviolet light for a long time.
t) Please storage modules in ambient temperature if possible. Below the storage temperature, liquid crystal
can freeze and damage the LCD paenel. Above storage temperature, it can irreversibly turn into isotropic
state which cannot work as display.
LD-20901A-14
12 Reliability Test Items
No.
1
Test parameter
Conditions
Leaves the module at Ta=80℃ for 240h
Leaves the module at Ta=-30℃ for 240h
High temperature storage test
Low temperature storage test
High temperature
2
3
Operates the module at Ta=40°C; 90~95%RH for 240h
(No condensation)
& high humidity operation test
High temperature operation test
Low temperature operation test
Strength against ESD
4
5
6
7
Operates the module with 80℃ at panel surface for 240h
Operates the module at Ta=-30℃ for 240h
±200V・200pF [0Ω] one time for each terminal
Max. acceleration : 980m/s2
Shock test
(non- operating)
Pulse width : 6ms, half sine wave
Direction : ±X,±Y,±Z
once for each direction.
8
Vibration test
～
Frequency : 10 57Hz/Vibration width (one side):0.15mm
～
: 57 500Hz/ acceleration:19.6m/s2
(non- operating)
Sweep time : 6 minutes
Test period : 3 hours
(1 hour for each direction of X,Y,Z)
-30℃~ 80℃/50 cycle
[0.5h] [0.5h]
9
Thermal shock test
[Result Evaluation Criteria]
Under the display quality test conditions with normal operation state, these shall be no change which
may affect practical display function.
[Note] The directions of X, Y, Z are defined as below:
Z
LD-20901A-15
13 Packing Form
13.1 Fig.3 shows packaging form.
13.2 Carton stock conditions
a) Maximum number of Carton being stuck: Max. 12 cartons
b) Maximum number of product contained: 20 Unit
c) Carton size:
d) Total mass :
442 mm(W)×390 mm(H)×170 mm(D)
5.9 kg
e) Carton stock environment:
１) Temperature:
2) Humidity:
0 ~ 40°C
Up to 60%RH
3) Ambiance:
4) Period:
No gases bite into electronic components and wiring materials
Approximately 3month
5) Unpacking:
To prevent LCD module from damaging by ESD,
unpack the module with effective measure after controlling
humidity 50%RH or more.
14 Others
1. Serial No. indication
Serial No. is indicated by labeling. The location is given in Fig.1 Outline dimension.
Indicated contents:
LQ057V3DG02
7X000001X
Model name
Serial No.
Serial No. contents
1st digit:
2nd digit:
3rd ~ 8th digit:
9th digit:
last digit of produced year (ex. 2007 → “7”)
Produced month 1, 2, 3 ~ 9, X, Y, Z
Sequential number 000001 ~
Interoffice control code
(There is the case of the blank.)
2. Liquid crystal panel drive input FFC/FPC specification
・Refer to the recommended FPC/FFC dimensions of the input connector.
[IMSA-9637S-33Y902(IRISO ELECTRONICS CO.,LTD.), 33pin 1.0mm pitch]
・The terminal of FFC/FPC of input connector recommend gold or gold plating specification.
Because point of contact with its is gold plating specification.
LD-20901A-16
LD-20901A-17
L
相关型号：
©2020 ICPDF网 联系我们和版权申明