GP1A05A2J00F [SHARP]
Gap : 5mm, Slit : 0.5mm OPIC Output Transmissive Photointerrupter with Connector; 差距：5毫米，缝： 0.5毫米OPIC输出透射光斩波器与连接器
| 型号： | GP1A05A2J00F |
| 厂家： | 
SHARP ELECTRIONIC COMPONENTS |
| 描述： | Gap : 5mm, Slit : 0.5mm OPIC Output Transmissive Photointerrupter with Connector |
| 文件： | 总12页 (文件大小：151K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
GP1A05AJ000F Series
Gap : 5mm, Slit : 0.5mm
OPIC Output
Transmissive Photointerrupter
with Connector
GP1A05AJ000F
Series
*
Description
Agency approvals/Compliance
■
■
GP1A05AJ000F Series are standard, OPIC output,
1. Compliant with RoHS directive
transmissive photointerrupters with opposing emitter and
detector in a case, providing non-contact sensing. For
this family of devices, the emitter and detector are insert-
ed in a case, and a 3-pin connector is included to allow
remote-mount or off-board designs.
Applications
■
1. General purpose detection of object presence or mo-
tion.
2. Example: PPC, FAX, Printer
Features
■
1. Transmissive with OPIC output
2. Highlights :
• Includes additional screw fixing holes
• Positioning Pin to prevent misalignment
3. Key Parameters:
• Gap Width : 5mm
• Slit Width (detector side) : 0.5mm
• Package : 34 18 11mm (without connector and
×
×
positloning pin)
• Connector : GP1A05AJ000F ; Tyco Electronics
AMP K.K. (PN : 171825-3)
GP1A05A2J00F ; J.S.T. Mfg Co., Ltd.
(PN : B3P-SHF-IAA (LF))
GP1A05A5J00F ; Molex-Japan Co.,
Ltd. (PN : 5267-03A)
• Output Type : High when the object is present with
Pullup Resistor
4. Lead free and RoHS directive compliant
* "OPIC"(Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and a signal-
processing
Notice The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
Sheet No.: D3-A04501EN
Date Oct. 3. 2005
© SHARP Corporation
1
GP1A05AJ000F Series
Internal Connection Diagram
■
1
2
3
Voltage regulator
Amp.
1
2
3
VCC
GND
VOUT
(In case of external addition pull-up resistance to VOUT terminal)
Truth table
Condition
Output
Light beam interrupted
High
Low
Light beam uninterrupted
(Unit : mm)
Outline Dimensions
GP1A05AJ000F
φ3±0.1 Depth2
■
GP1A05A2J00F
φ3±0.1 Depth 2
2
2
Model No.
Model No.
1
2
3
1
2
3
7
7
3.5
3.5
Slit width0.5±0.1
15
5
15
Slit width 0.5±0.1
5
5
5
Protrusion of connector
from holder : Max.1
Connector : 171825-3
(Tyco Electronics AMP K.K.)
Connector
B3P-SHF-1AA (LF)
:
C0.5
C0.5
(J.S.T. MFG. CO., LTD.)
34
10.4±1
34
9.2±1
Model
Date code
indicator (Year)
Model
Date code
indicator (Year)
Z
0
5
6
Z
0
5
6
11±0.1
12±0.1
11±0.1
12±0.1
Date code indicator (month)
Date code indicator (month)
• Unspecified tolerance shall be as
follows ;
• Unspecified tolerance shall be as
follows ;
Dimensions(d)
less than 4
Tolerance
Dimensions(d)
less than 4
Tolerance
0.2
±
0.3
±
0.5
±
0.2
0.3
0.5
±
±
±
4 or more less than 16
16 or more
4 or more less than 16
16 or more
Product mass : approx. 3.0g
Connector terminal plating material : Sn
Product mass : approx. 3.0g
Connector terminal plating material : Sn
Sheet No.: D3-A04501EN
2
GP1A05AJ000F Series
(Unit : mm)
GP1A05A5J00F
φ3±0.1 Depth 2
2
Model No.
7
3.5
15
5
Slit width 0.5±0.1
5
C0.5
3
2 1
Connector : 5267-03A
(MOLEX-JAPAN CO., LTD.)
34
Model
indicator (Year)
Date code
5.9±1
Z
0
5
6
11±0.1
12±0.1
Date code indicator (month)
• Unspecified tolerance shall be as
follows ;
Dimensions(d)
less than 4
Tolerance
0.2
0.3
0.5
±
±
±
4 or more less than 16
16 or more
Product mass : approx. 3.0g
Connector terminal plating material : Sn
Sheet No.: D3-A04501EN
3
GP1A05AJ000F Series
Date code
Year of production
Month of production
Month
Mark
1
2
1
2
3
3
4
4
5
5
Last two digits of
Christian year.
6
6
7
7
8
8
9
9
10
11
12
X
Y
Z
Country of origin
Japan or Philippines
(Indicated on the packing case)
Sheet No.: D3-A04501EN
4
GP1A05AJ000F Series
Absolute Maximum Ratings
■
(T 25˚C)
=
a
Parameter
Symbol
VCC
Rating
Unit
Supply
voltage
0.5 to 10
GP1A05AJ000F
−
+
V
0.5 to 8
GP1A05A2J00F/GP1A05A5J00F
−
+
*1 Output voltage
VOUT
IOL
0.5 to 28
V
mA
˚C
−
+
*2 Low level output current
*3 Operating temperature
*3 Storage temperature
50
Topr
Tstg
20 to 75
−
+
40 to 85
˚C
−
+
∗1 Collector-emitter voltage of output transistor.
∗2 Collector current of output transistor, refer to Fig.1.
∗3 The connector should be plugged in/out at normal temperature.
Electro-optical Characteristics
■
(VCC 5V, T 25˚C)
=
=
a
Parameter
Symbol
ICCL
VOL
ICCH
VOH
f
Conditions
Light beam uninterrupted
MIN.
TYP. MAX.
Unit
Low level supply current
Low level output voltage
High level supply current
High level output voltage
30
0.35
30
mA
V
−
−
−
−
−
Light beam uninterrupted, IOL=16mA
Light beam interrupted
mA
V
−
Light beam interrupted, R 47k
VCC 0.9
=
Ω
×
−
−
L
*4 Response frequency
R
47k
3 000
5.5
0.5
0.5
Hz
V
=
L
Ω
−
4.5
−
−
Operating supply voltage
VCC
tr
−
−
Rise time
Fall time
0.1
0.05
s
s
μ
μ
*5 Response time
R
L
280
=
Ω
tf
−
∗4 Response frequency is measured with the disk shown below being rotated.
∗5 Refer to Fig.7.
(Unit : mm)
Disk
Sheet No.: D3-A04501EN
5
GP1A05AJ000F Series
Fig.1 Low Level Output Current vs.
Fig.2 Low Level Output Voltage vs.
Ambient Temperature
Low Level Output Current
60
1.0
VCC=5V
Ta=25˚C
50
40
30
0.1
20
16.6
10
0
0.01
1
10
Low level output current IOL (mA)
100
−20
0
25
50
75
100
Ambient temperature Ta (˚C)
Fig.3 Low Level Output Voltage vs.
Fig.4 Supply Current vs. Supply Voltage
Ambient Temperature
30
0.6
VCC=5V
0.5
20
0.4
Ta=−20˚C
+25˚C
I
OL=30mA
0.3
0.2
0.1
0
ICCL
+75˚C
10
ICCH
Ta=−20˚C, +25˚C, +75˚C
16mA
5mA
0
4.5
5.0
5.5
−25
0
25
50
75
100
Supply voltage VCC (V)
Ambient temperature Ta (˚C)
Fig.5 Detecting Position Characteristics (1)
Fig.6 Detecting Position Characteristics (2)
(Detecting position : d=3.5±0.3
)
(Detecting position :h=3
)
−1.5
+2
V
CC=5V
VCC=5V
Ta=25˚C
Output "High"
Output "High"
Ta=25˚C
RL=47kΩ
RL=47kΩ
Shield
0
Shield
d
Sensor
Sensor
Output "Low"
Output "Low"
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
Shield moving distance d (mm)
Shield moving distance h (mm)
Sheet No.: D3-A04501EN
6
GP1A05AJ000F Series
Fig.7 Test Circuit for Response Time
Input
Output
td
VCC
RL
RD
Input
Output
10%
90%
ts
tr
tf
Remarks : Please be aware that all data in the graph are just for reference and not for guarantee.
Sheet No.: D3-A04501EN
7
GP1A05AJ000F Series
Design Considerations
■
●
Design guide
1) Prevention of detection error
To prevent photointerrupter from faulty operation caused by external light, do not set the detecting face to
the external light.
2) In order to stabilize power supply line, connect a by-pass capacitor of more than 0.01 F between VCC and
μ
GND near the device.
3) When the sensor is connected with long wire, noise might be on the signal from the sensor while it is
going through the wire. To avoid this problem, please evaluate the sensor under actual usage condition to
make sure that the system works fine.
4) Position of opaque board
Opaque board shall be installed at place 5mm or more from the top of elements.
(Example)
5mm or more
5) Screw tightening torque
The tightening torque for screwing should be 0.6N m or less.
⋅
This product is not designed against irradiation and incorporates non-coherent IRED.
●
Parts
This product is assembled using the below parts.
[Using a silicon photodiode as light detecting portion, and a bipolar IC as signal processing circuit]
• Photodetector (qty. : 1)
Maximum Sensitivity
wavelength (nm)
Sensitivity
wavelength (nm)
Category
Response time (μs)
Photodiode
900
400 to 1 200
3
• Photo emitter (qty. : 1)
Maximum light emitting
Category
Material
I/O Frequency (MHz)
0.3
wavelength (nm)
Infrared emitting diode
(non-coherent)
Gallium arsenide (GaAs)
950
Sheet No.: D3-A04501EN
8
GP1A05AJ000F Series
• Material
Case
Connector terminal finish
Black Polcarbonate resin
(UL94 HB)
Sn plating
• Others
Laser generator is not used.
Sheet No.: D3-A04501EN
9
GP1A05AJ000F Series
Manufacturing Guidelines
■
●
Notes of cleaning
Please carry out neither the immersion cleaning nor the ultrasonic cleaning to avoid the solvent residue in-
side the case.
When necessary, dust and stain shall clean by air-blow or wipe off by soft cloth soaked in cleaning agent.
The cleaning agent used to wipe off must use only the following kind. Ethyl alcohol, Methyl alcohol and Iso-
propyl alcohol.
●
Presence of ODC
This product shall not contain the following materials.
And they are not used in the production process for this product.
Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform)
Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all.
This product shall not contain the following materials banned in the RoHS Directive (2002/95/EC).
•Lead, Mercury, Cadmium, Hexavalent chromium, Polybrominated biphenyls (PBB), Polybrominated
diphenyl ethers (PBDE).
Sheet No.: D3-A04501EN
10
GP1A05AJ000F Series
Package specification
■
●
Case package
Package materials
Anti-static plastic bag : Polyethtylene
Moltopren : Urethane
Partition : Corrugated fiberboard
Packing case : Corrugated fiberboard
Package method
75 pcs of products shall be packaged in a plastic bag, Ends shall be sealed by stapler. The bottom ot the
packing case is covered with moltopren, and the partition is set in the packing case. Each partition should
have 1 plastic bag.
Moltopren should be located after all product are settled (1 packing conteains 150 pcs).
Packing composition
Moltopren
Plastic bag
Packing case
Sheet No.: D3-A04501EN
11
GP1A05AJ000F Series
Important Notices
■
· The circuit application examples in this publication
are provided to explain representative applications of
SHARP devices and are not intended to guarantee any
circuit design or license any intellectual property rights.
SHARP takes no responsibility for any problems related
to any intellectual property right of a third party resulting
from the use of SHARP's devices.
with equipment that requires higher reliability such as:
--- Transportation control and safety equipment (i.e.,
aircraft, trains, automobiles, etc.)
--- Traffic signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii) SHARP devices shall not be used for or in
connection with equipment that requires an extremely
high level of reliability and safety such as:
--- Space applications
· Contact SHARP in order to obtain the latest device
specification sheets before using any SHARP device.
SHARP reserves the right to make changes in the
specifications, characteristics, data, materials, structure,
and other contents described herein at any time
without notice in order to improve design or reliability.
Manufacturing locations are also subject to change
without notice.
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment (e.g.,
scuba).
· If the SHARP devices listed in this publication fall
within the scope of strategic products described in the
Foreign Exchange and Foreign Trade Law of Japan, it
is necessary to obtain approval to export such SHARP
devices.
· Observe the following points when using any devices
in this publication. SHARP takes no responsibility for
damage caused by improper use of the devices which
does not meet the conditions and absolute maximum
ratings to be used specified in the relevant specification
sheet nor meet the following conditions:
· This publication is the proprietary product of SHARP
and is copyrighted, with all rights reserved. Under
the copyright laws, no part of this publication may be
reproduced or transmitted in any form or by any means,
electronic or mechanical, for any purpose, in whole or in
part, without the express written permission of SHARP.
Express written permission is also required before any
use of this publication may be made by a third party.
(i) The devices in this publication are designed for use
in general electronic equipment designs such as:
--- Personal computers
--- Office automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
--- Consumer electronics
· Contact and consult with a SHARP representative
if there are any questions about the contents of this
publication.
(ii) Measures such as fail-safe function and redundant
design should be taken to ensure reliability and safety
when SHARP devices are used for or in connection
Sheet No.: D3-A04501EN
[H170]
12
相关型号：
GP1A073LCS
Gap : 5mm Slit : 0.5mm OPIC Output, Snap-in type Transmissive Photointerrupter with Connector
SHARP
©2020 ICPDF网 联系我们和版权申明