SS41FKSOT [SECELECTRONICS]
Hall Latch Position Sensor;
| 型号： | SS41FKSOT |
| 厂家： | 
SEC Electronics Inc. |
| 描述： | Hall Latch Position Sensor |
| 文件： | 总6页 (文件大小：237K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SS41F
Hall Latch Position Sensor
Features and Benefits
Application Examples
–
–
–
–
–
–
–
–
–
4.5V to 24V Operation
-40°C to 150°C Superior temperature operation
Bipolar technology
Open-collector 25 mA output
Reverse battery protection
Small Size SOT23 3L or SIP 3L
Solid-state reliability
Resistant to physical stress
Activate with small, commercially available
permanent magnets
–
–
–
–
–
–
–
Brushless DC motor commutation
Automotive, Consumer and Industrial
Solid-state switch
Speed measurement
Revolution counting
Angular position detection
Proximity detection
3 pin SOT23 (suffix SO)
3 pin SIP (suffix UA)
Functional Block Diagram
SIP Package
Pin 1 – VDD
Pin 2 – GND
Pin 3 – OUT
SOT Package
Pin 1 – VDD
Pin 2 – OUT
Pin 3 – GND
1
V3.10 Nov 1, 2013
SS41F
Hall Latch Position Sensor
General Description
The SS41F is an integrated Hall effect latched sensor
designed for electronic commutation of brush-less
DC motor applications. The device integrates a
voltage regulator, reverse battery protection diode,
Hall sensor with dynamic offset cancellation system,
temperature compensation circuitry, small signal
amplifier, Schmitt trigger and an open-collector
output to sink up to 25 mA.
temperature and supply voltage changes. If a mag-
netic flux density larger than threshold Bop, Output
is turned on (low). The output state is held until a
magnetic flux density reversal falls below Brp,
causing Output to be turned off (high).
Thanks to its wide operating voltage range and ex-
tended choice of temperature range, it is quite suita-
ble for use in DC motor applications.
These Hall-effect switches are monolithic integrated
circuits with tighter magnetic specifications, de-
signed to operate continuously over extended tem-
peratures to +150°C,and are more stable with both
The device is delivered in a Small Outline Transistor
(SOT) or in a Plastic Single In Line (SIP 3L flat).
Both 3-lead packages are RoHS compliant.
Glossary of Terms
MilliTesla (mT), Gauss Units of magnetic flux density: 1mT = 10 Gauss
RoHS
Restriction of Hazardous Substances
Operating Point (BOP)
Magnetic flux density applied on the branded side of the package which turns the
output driver ON (VOUT = VDSon
)
Release Point (BRP)
Magnetic flux density applied on the branded side of the package which turns the
output driver OFF (VOUT = high)
2
V3.10 Nov 1, 2013
SS41F
Hall Latch Position Sensor
Pin Definitions and Descriptions
SOT Pin № SIP Pin №
Name
VDD
Type
Supply
Output
Ground
Function
1
2
3
1
3
2
Supply Voltage pin
Open Drain Output pin
Ground pin
OUT
GND
Absolute Maximum Ratings
Symbol
VDD
IDD
Parameter
Value
Units
V
Supply Voltage
Supply Current
28
50
28
50
mA
V
VOUT
IOUT
TS
Output Voltage
Output Current
mA
Storage Temperature Range
-65 to 170
°C
Symbol
TA
Operating Temperature Range
Temperature Suffix “E”
Temperature Suffix “K”
Temperature Suffix “L”
Value
Units
°C
-40 to 85
-40 to 125
-40 to 150
TA
°C
TA
°C
Exceeding the absolute maximum ratings may cause permanent damage. Exposure to absolute-maximum- rated conditions for ex-
tended periods may affect device reliability.
3
V3.10 Nov 1, 2013
SS41F
Hall Latch Position Sensor
General Electrical Specifications
DC Operating Parameters TA = 25°C, VDD= 4.5V to 24V (unless otherwise specified)
Typ
Parameter
Symbol Test Conditions
Min
Max
24
Units
V
VDD
IDD
V
Supply Voltage
Operating
4.5
B <
BRP
5
0.4
0.01
0.3
0.3
Supply Current
10
mA
V
IOUT = 20mA, B >
Output Saturation Voltage
Output Leakage Current
Output Rise Time
Output Fall Time
0.5
5
DSon
BOP
IOFF
B <
VOUT = 24V
BRP
µA
µs
t
1.5
1.5
r
RL = 1KΩ, CL = 20pF
RL =1KΩ, CL = 20pF
t
f
µs
Magnetic Specifications
DC Operating Parameters VDD = 4.5 to 24V (unless otherwise specified)
Package
Parameter
Symbol
BOP
Test Conditions
Min
Typ
Max
Units
G
Operating Point
Release Point
Hysteresis
5
45
-45
90
90
-5
UA
BRP
Ta=25°C,Vdd=12V DC
-90
G
BHYST
BOP
G
Operating Point
Release Point
Hysteresis
-90
5
-45
45
-5
G
SO
BRP
Ta=25°C,Vdd=12V DC
90
G
BHYST
90
G
Output Behavior versus Magnetic Pole
DC Operating Parameters TA = -40°C to 150°C, VDD = 4.5 to 24V (unless otherwise specified)
Test Conditions (UA) Test Conditions (SO)
OUT
High
Low
B < BRP
B > BOP
B > BRP
B < BOP
The SOT-23 device is reversed from the UA package. The SOT-23 output transistor will be turned on(drops low) in the presence of a
sufficiently strong North pole magnetic field applied to the marked face and turned off(hoists high) in the presence of a sufficiently
strong South pole magnetic field.
4
V3.10 Nov 1, 2013
SS41F
Hall Latch Position Sensor
Application Information
Package Information
Package TO, 3-Pin SIP:
2.13
3° ± 1°
1.00
1.20
45° ± 1°
4.0 ± 0.01
2
3
Sensor Location
0.84(Nom)
6° ± 1°
Active Area Depth:
3° ± 1°
0.44± 0.01
1
3
6° ± 1°
3° ± 1°
0.05 ± 0.05
0.39± 0.01
0.38 ± 0.01
Notes:
1). Controlling dimension : mm ;
2). Leads must be free of flash and plating voids ;
3). Do not bend leads within 1 mm of lead to package
interface ;
4). PINOUT: Pin 1 VDD
Pin 2 GND
Pin 3 Output
1.27
2.54
5
V3.10 Nov 1, 2013
SS41F
Hall Latch Position Sensor
Package SO, 3-Pin SOT-23：
Notes
1). PINOUT: Pin 1 VDD
Pin 2 Output
Top
3
Pin 3 GND
2). All dimensions are in millimeters;
2.60
3.00
1.50
1.80
1
2
1.70
2.10
Side Vie
End
2.70
3.10
0.10
0.25
1.00
1.30
0.70
0.90
0.20
Min
0.00
0.10
0.35
0.50
Ordering Information
Part No.
Pb-free
YES
YES
YES
YES
YES
YES
Temperature Code
-40°C to 85°C
Package Code
SOT-23
TO-92
Packing
SS41FESOT
SS41FEUA
SS41FKSOT
SS41FKUA
SS41FLSOT
SS41FLUA
7-in. reel, 3000 pieces/ reel
Bulk, 1000 pieces/ bag
7-in. reel, 3000 pieces/ reel
Bulk, 1000 pieces/ bag
7-in. reel, 3000 pieces/ reel
Bulk, 1000 pieces/ bag
-40°C to 85°C
-40°C to 125°C
-40°C to 125°C
-40°C to 150°C
-40°C to 150°C
SOT-23
TO-92
SOT-23
TO-92
6
V3.10 Nov 1, 2013
相关型号：
SS41G
Hall Effect Sensor, -25mT Min, 25mT Max, 20mA, Rectangular, Through Hole Mount, 3.0 X 4.0 MM, PLASTIC PACKAGE-3
HONEYWELL
©2020 ICPDF网 联系我们和版权申明