LB1967 [SANYO]
Fan Motor 2-Phase Half-Wave Driver; 风扇电机2相半波驱动型号: | LB1967 |
厂家: | SANYO SEMICON DEVICE |
描述: | Fan Motor 2-Phase Half-Wave Driver |
文件: | 总4页 (文件大小:37K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Ordering number : ENN6115
Monolithic Digital IC
LB1967M
Fan Motor 2-Phase Half-Wave Driver
Overview
Package Dimensions
unit: mm
The LB1967M is a brushless motor driver IC for 2-phase half-
wave drive well suited for compact fan motor for communica-
tion and office equipment, etc.
3086A-MFP10S
[LB1967M]
Features
10
6
• Dual power supply voltage design (5/12V) and wide voltage
handling range
• Built-in Hall amplifier with hysteresis (supports core
without auxiliary electrode)
• Built-in lockup protection and automatic recovery circuits
(External capacitor for rotation detection need only be 0.1
µF, allowing compact, cost-saving design)
1
5
0.15
5.1
• Built-in FG output (Vosat = 0.2Vtyp at I = 5 mA)
O
• Built-in output transistor with output withstand voltage
24Vmin/output current 500 mA (average), 1.2A (peak)
• Built-in thermal protection circuit
0.35
0.55
1.0
SANYO : MFP10S
• Compact, high-temperature resistant MFP-10 package
reduces external parts count and mounting space, therefore
making this IC support the motors with a wide range of
sizes and speeds.
Specification
Absolute Maximum Ratings at Ta = 25°C
Parameter
Maximum supply voltage
Output current
Symbol
Conditions
Ratings
Unit
V
max
18
500
V
CC
I
ave
mA
mA
V
OUT
I
peak t ≤ 1 ms
1200
Internal
10
OUT
Output withstand voltage
FG output current
V
max
OUT
IFG max
mA
V
FG output withstand voltage
Allowable power dissipation
Operating temperature
Storage temperature
VFG
max
18
OUT
Pd max
With specified substrate *
800
mW
°C
Topr
Tstg
–30 to +85
–55 to +150
°C
* Specified substrate (114.3 × 76.1 × 1.5 mm3, glass exposy)
Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft's
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
O2599RM(KI) No. 6115-1/4
LB1967M
Recommended Operating Ranges at Ta = 25°C
Parameter
Power supply voltage
Common mode input voltage range
Symbol
Conditions
Ratings
Unit
V
V
V
1
3.6 to 17
CC
0.2 to V –2.3
CC
V
COM
Electrical Characteristics at Ta = 25°C, V = 12V
CC
Ratings
Parameter
Circuit current
Symbol
Conditions
Unit
min
typ
max
I
In drive mode (CT = L)
In lockup protection mode (CT = H)
3
4
5
6
mA
mA
µA
µA
–
CC
CT capacitor charge current
Capacitor discharge current
Capacitor discharge current ratio
CT charge voltage
I
I
1
2
V
V
= 0.2V
= 8V
0.8
1.2
0.24
5.0
2.0
0.4
7.0
7.6
1.8
27.0
1.3
18
CT
CT
CT
CT
0.16
4.0
R
R
= I 1/I
2
CT
CT
CT CT
V
1
6.8
7.2
V
CT
CT
V
V
2
1.4
1.6
V
Output limiter withstand voltage
Output saturation voltage
Hall input sensitivity
I
= 10 mA
24.0
25.5
1.0
V
OLM
O
V
I
= 500 mA
V
OL
HN
FG
O
V
V
Including offset and hysteresis
2
10
mV
V
FG output saturation voltage
FG output leak current
I
= 5 mA
= 14V
FG
0.2
0.5
10
O
V
V
0.1
µA
°C
FL
+
Thermal protection trigger temperature
V
Assured design target *
150
180
210
TH
* Assured design target; Target value, not measured individually
Truth Table
–
+
IN
IN
L
CT
OUT1
OUT2
FG
L
Mode
H
L
–
L
H
H
L
L
Rotating
H
–
H
H
off
off
–
Lockup protection activated
Pin Assignment
Pd max – Ta
With specified substrate
1000
800
600
400
MFP-10
3
(114.3×76.1×1.5 mm , glass exposy)
FG
IN+
NC
IN–
1
2
3
4
5
10 V
CC
9
8
7
6
CT
LB1967M
NC
416
OUT2
GND
200
0
OUT1
Top view
–30
0
30
60
90
120
A12231
Ambient temperature, Ta – °C
No. 6115-2/4
LB1967M
Sample Application Circuit
5/12V power supply (3.8 to 17V)
10kΩ
0.01µF
10
V
CC
OUT1
OUT2
5
7
IN+
IN–
2
4
H
1
FG
9
CT
GND
6
On-board parts
A12232
Precautions
–
• Wiring layout for IN and OUT1 must be designed to prevent interference.
• If the wiring between the Hall element and the IC input is long, noise interference may lead to chattering in the FG
+
–
output waveform. In this case, insert a capacitor with 0.01 to 0.001 µF between IN and IN .
• If CT pin is connected to GND, the lockup protection and restart functions are disabled.
• In a circuit configuration as shown above, a current-GND reverse connection will cause a current to flow as follows:
GND -> OUT -> coil -> power supply. The magnitude of this current is limited by the coil resistance. If it is less
than 500 mA, the IC will not be destroyed. If required, insert a diode between V and the coil.
CC
No. 6115-3/4
LB1967M
Block Diagram and Sample Application Circuit
L1
L2
Thermal
protection
circuit
10
V
CC
5
OUT1
IN+
IN–
2
4
Control block
H
OUT2
7
1
FG
Constant
current
circuit
CT
9
C1
6
GND
A12233
Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer's
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer's products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products(including technical data,services) described or
contained herein are controlled under any of applicable local export control laws and regulations,
such products must not be exported without obtaining the export license from the authorities
concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification"
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.
This catalog provides information as of October, 1999. Specifications and information herein are subject to change
without notice.
No. 6115-4/4
PS
相关型号:
©2020 ICPDF网 联系我们和版权申明