IPD1-23-S-R [SAMTEC]
Board Connector, 23 Contact(s), 1 Row(s), Female, 0.1 inch Pitch, Crimp Terminal, Latch, White Insulator;
| 型号： | IPD1-23-S-R |
| 厂家： | 
SAMTEC |
| 描述： | Board Connector, 23 Contact(s), 1 Row(s), Female, 0.1 inch Pitch, Crimp Terminal, Latch, White Insulator |
| 文件： | 总3页 (文件大小：225K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
REVISION N
IPD1-XX-S-X-X
C1
OPTION
-R: RETENTION LATCH
(SEE NOTE 16) (SEE SHEET 3)
.007
.003
DO NOT
SCALE FROM
THIS PRINT
No OF POSITIONS
((No OF POSITIONS x .100) + .055)
.078±.010
-02 THRU -25
(PER ROW)
[SEE FIG. 2 FOR -02 POSITION]
OPTION
-K: KEYED POLARIZATION
(SEE FIGURE 3, SHEET 2)
.050
.035±.010
.08
ROW SPECIFICATION
-S: SINGLE
NOTES:
C
1.
REPRESENTS A CRITICAL DIMENSION.
2. SAMTEC LOGO SHALL APPEAR AT ONE LOCATION ON SURFACE SHOWN,
APPROXIMATELY .150 x .094 (BOTH SIDES).
+.006
-.000
.505
3. ALL MULTIPLE CAVITY MOLDS SHALL IDENTIFY EACH CAVITY WITH A LETTER
DESIGNATION LOCATED WHERE SHOWN.
+.005
-.003
C2
.220
4. ALL IDENTIFICATION MARKS MUST NOT STAND GREATER THAN .002 OFF THE
SURFACE OF THE PART.
5. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE
FREE OF SCATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES.
6. MAX ALLOWABLE BOW: SEE TABLE 1. BOW TO BE MEASURED AT MIDLINE OF PART.
7. PART TO BE SYMMETRIC ABOUT THE CENTERLINE WITHIN +/-.002, UNLESS
OTHERWISE STATED.
8. NUMBER OF POSITIONS (PER ROW) TO BE SHOWN IN THIS AREA EXCLUDING
2, 3 AND 4 POSITIONS. SIZE AND DEPTH SIMILAR TO POSITION 1 INDICATOR.
9. GATE PADS MUST BE RECESSED .005. GATE LOCATION IS AT MOLDERS DISCRETION.
10. END CORES ARE POLARIZED. CONFIRM GEOMETRY RELATIVE TO POSITION 1
INDICATOR & GATE PADS.
11. POSITION 1 INDICATOR TO BE .0005 MAX DEPTH, NOT PRESENT ON 2-4 POSITION
OPTIONS.
SEE NOTE 11
C3
.050 (TYP)
.002
.003
((No OF POSITIONS -1) x .100)
(MEASURED AT BASE OF TOWER)
.0775
(4 PLCS)
'C'
C4
"A"
.300
.200±.002
12. SPECIFIED POSITIONS TO BE IDENTIFIED WHERE SHOWN (NOTE 4 APPLIES).
13. MOLD DESIGNER HAS DISCRETION OVER RIB LOCATION. STEEL PRINT SETUP
SHEET MUST SHOW RIB CONFIGURATION FOR EACH PART NUMBER.
14. PART MUST DRAFT INWARD FROM BOTTOM TO TOP OF STACK.
15. ALL DIMENSIONS TO BE SYMMETRIC ABOUT CENTERLINE WITHIN .0015
UNLESS OTHERWISE STATED.
FIG. 1
IPD1-06-S SHOWN
'B'
"A"
16. OPTION NOT FOR SALE. FOR RETENTION LATCH FEATURE , SEE IPD1-XX-S-M PRINT.
'A'
.0723
(SEE NOTE 14)
.0923
(SEE NOTE 14)
"B"
'H'
'F'
'E'
C5
SEE NOTE 8
.4800±.0020
PARTING LINE
.045
.255
.100±.005
"B"
SEE NOTE 2
SEE NOTE 3
'D'
.112
.082
+.002
-.001
C6
.059
SECTION "A"-"A"
SECTION "B"-"B"
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
.020 (2 PLCS)
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
.XX: .01 [.3]
2
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
.XXX: .003 [.08]
.XXXX: .0015 [.038]
'G'
SHEET SCALE: 2:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
.300
.100 SHROUDED CONTACT BODY
ZYTEL 101F, COLOR: WHITE
MAX REGRIND: 25%
MAX FLASH ALLOWED: .004
MAX GATE VESTIGE: .002
DWG. NO.
06 05 04 03 02 01
IPD1-XX-S-X-X
SEE NOTE 12
BY:
DEAN P
04/25/2005 SHEET 1 OF 3
F:\DWG\MISC\Mktg\IPD1-XX-S-X-X-MKT.SLDDRW
REVISION N
.0310 SQ (TYP)
15°+-24°° (TYP)
.060
+.0030
.0895
-.0000
C7
.0187
'N'
.100 REF
C8
.075±.002
(TYP)
C9
.145±.002
.100 (TYP)
C11
.035
+.003
-.002
.0400 (TYP)
.0850
R.025
(TYP)
+.003
-.000
DETAIL 'C'
.0750
SCALE 5 : 1
+5°
-2°
(TYP)
18° (TYP)
.225±.005
.085
.0200 (TYP)
.0800 (TYP)
C10
DETAIL 'G'
.145
SCALE 5 : 1
DETAIL 'D'
SCALE 5 : 1
DETAIL 'A'
DETAIL 'B'
SCALE 5 : 1
SCALE 3 : 1
.0110
.0108
.0030
C12
FIG. 2
+.002
-.001
.0690
-02 POSITION
(SAME AS FIG. 1, UNLESS OTHERWISE STATED)
34°
.005
.076
2° REF
30° (TYP)
+.000
-.003
.110
DETAIL 'N'
SCALE 10 : 1
.015
.0100
.0020
20°
.006 (TYP)
C13
.200
.1300
.250
+.001
-.003
.105
.020 (TYP)
.4550
.0159
30°
.0250
R.025
(TYP)
DETAIL 'H'
SCALE 12 : 1
.0100
.030
C14
.325
FIG. 3
.020
.0300
-K: KEYED POLARIZATION
.068
(IPD1-06-S-K SHOWN)
(SAME AS FIG. 1, UNLESS OTHERWISE STATED)
.0735
.041
15° (TYP)
MAX FLASH .006 THIS AREA ONLY
DETAIL 'E'
SCALE 8 : 1
DETAIL 'F'
SCALE 4 : 1
"N"
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
code: 55322
e-Mail: info@SAMTEC.com
DESCRIPTION:
DO NOT SCALE DRAWING
.100 SHROUDED CONTACT BODY
2°
SHEET SCALE: 2:1
DWG. NO.
IPD1-XX-S-X-X
SECTION "N"-"N"
SCALE 4 : 1
"N"
F:\DWG\MISC\Mktg\IPD1-XX-S-X-X-MKT.SLDDRW
BY:
DEAN P
04/25/2005 SHEET 2 OF 3
FIG. 5
( IPD1-02-S-R SHOWN)
(SAME AS FIG.2, UNLESS OTHERWISE STATED)
(SEE NOTE 16)
FIG. 4
( IPD1-06-S-R SHOWN)
(SAME AS FIG.1, UNLESS OTHERWISE STATED)
(SEE NOTE 16)
REVISION N
.0015
NOT RELEASED FOR PRODUCTION
NOT RELEASED FOR PRODUCTION
DETAIL 'M'
SCALE 6 : 1
.0400
'M'
"J"
C15
+.000
-.001
.041
.250
.126
.1700
"A"
(SEE TABLE 2)
.0327
R.055
"J"
.230
C16
.0170±.0010
SECTION "J"-"J"
SCALE 5 : 1
.355
"K"
"K"
C17
.1600±.0010
'L'
C18
.1700±.0010
.1800±.0010
C19
.0085 X 45°
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
R.005 (TYP)
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
code: 55322
.035
e-Mail: info@SAMTEC.com
.040
.065
.070
DESCRIPTION:
SECTION "K"-"K"
SCALE 6 : 1
DO NOT SCALE DRAWING
SHEET SCALE: 4:1
.100 SHROUDED CONTACT BODY
DWG. NO.
DETAIL 'L'
SCALE 8 : 1
IPD1-XX-S-X-X
F:\DWG\MISC\Mktg\IPD1-XX-S-X-X-MKT.SLDDRW
BY:
DEAN P
04/25/2005 SHEET 3 OF 3
相关型号：
IPD1-25-D-KCC79L-2024-01-S
Board Connector, 50 Contact(s), 2 Row(s), Female, IDC Terminal, ROHS COMPLIANT
SAMTEC
IPD1-25-D-KCC79L-2630-01-S
Board Connector, 50 Contact(s), 2 Row(s), Female, IDC Terminal, ROHS COMPLIANT
SAMTEC
IPD1-25-D-KCC79R-2024-01-S
Board Connector, 50 Contact(s), 2 Row(s), Female, IDC Terminal, ROHS COMPLIANT
SAMTEC
IPD1-25-D-KCC79R-2630-01-S
Board Connector, 50 Contact(s), 2 Row(s), Female, IDC Terminal, ROHS COMPLIANT
SAMTEC
IPD1-25-DCC79L2024-01-S
Board Connector, 50 Contact(s), 2 Row(s), Female, IDC Terminal, ROHS COMPLIANT
SAMTEC
©2020 ICPDF网 联系我们和版权申明