IPD1-09-D-G-R [SAMTEC]

Rectangular Power Connector, 18 Contact(s), Female;


型号：	IPD1-09-D-G-R
厂家：	SAMTEC
描述：	Rectangular Power Connector, 18 Contact(s), Female
文件：	总4页 (文件大小：554K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

IPD1-XX-D-X-X

REVISION U

FIG. 1

OPTION

No OF POSITIONS

IPD1-06-D SHOWN

+.007

-.003

-R: RETENTION LATCH (SEE NOTE 16)

-02 THRU -25

(PER ROW)

((No OF POSITIONS x .100) + .058)

(SEE SHEET 3, FIG. 6)

[SEE FIG. 2 FOR -02 POSITION]

.078±.010

.035±.010

POLARIZATION OPTION

-P: POLARIZED

.050

(NOT AVAILABLE WITH -K OR-G OPTIONS)

(LEAVE BLANK FOR

ROW SPECIFICATION

-D: DOUBLE

NO POLARIZATION)(SEE FIG. 3)

-K: KEYED POLARIZATION

(NOT AVAILABLE WITH

-P OR -G OPTIONS)(SEE SHEET 2, FIGS. 4 & 5)

**-G: GUIDE POSTS

+.005

-.000

.08

.505

(NOT AVAILABLE WITH -P OR -K OPTIONS)

(SEE SHEET 4, FIG.8)

NOTES:

.220

** NOT RELEASED FOR RPODUCTION

REPRESENTS A CRITICAL DIMENSION.

2. SAMTEC LOGO SHALL APPEAR AT ONE LOCATION ON SURFACE SHOWN,

APPROXIMATELY .060 x .090 ON SIDE WITH LATCH AND .120 X .180 ON SIDE OPPOSITE OF LATCH.

3. ALL MULTIPLE CAVITY MOLDS SHALL IDENTIFY EACH CAVITY WITH A LETTER

DESIGNATION LOCATED WHERE SHOWN.

SEE NOTE 11

4. ALL IDENTIFICATION MARKS MUST NOT STAND GREATER THAN .002 OFF THE

SURFACE OF THE PART.

5. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE FREE

OF SCRATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES.

6. MAX ALLOWABLE BOW: SEE TABLE 1. BOW TO BE MEASURED AT MIDLINE OF PART.

7. PART TO BE SYMMETRIC ABOUT THE CENTERLINE WITHIN +/-.0015, UNLESS OTHERWISE

STATED.

8. NUMBER OF POSITIONS (PER ROW) TO BE SHOWN IN THIS AREA EXCLUDING 2, 3 AND 4

POSITIONS. SIZE AND DEPTH SIMILAR TO POSITION 1 INDICATOR.

9. GATE PADS MUST BE RECESSED .005.

.050 (TYP)

+.005

-.003

((No OF POSITIONS -1) x .100)

'C'

.0775

(4 PLCS)

DO NOT

SCALE FROM

THIS PRINT

10. END CORES ARE POLARIZED. CONFIRM GEOMETRY RELATIVE TO POSITION 1

INDICATOR & GATE PADS.

11. POSITION 1 INDICATOR TO BE RAISED .005 MAX, NOT PRESENT ON 2 POSITION OPTION.

12. SPECIFIED POSITIONS TO BE IDENTIFIED WHERE SHOWN (NOTE 4 APPLIES).

13. MOLD DESIGNER HAS DISCRETION OVER RIB LOCATION. STEEL PRINT SETUP SHEET MUST

SHOW RIB CONFIGURATION FOR EACH PART NUMBER.

14. PART MUST DRAFT INWARD FROM BOTTOM TO TOP OF STACK.

15. NOTE DELETED.

16. FOR RETENTION LATCH FEATURE, SEE IPD1-XX-D-X-M PRINT.

.250±.002

"A"

.353 .100

"A"

'B'

'A'

.0741

(SEE NOTE 14)

.0929

(SEE NOTE 14)

"B"

'H'

'F'

'E'

SEE NOTE 8

PARTING LINE

.4800±.0020

.045

FIG. 2

-02 POSITION

(SAME AS FIG. 1, UNLESS OTHERWISE STATED)

.100±.005

"B"

.255

'D'

SEE NOTE 2

SEE NOTE 3

.112

.082

+.002

-.001

.059

SECTION "A"-"A"

SECTION "B"-"B"

PROPRIETARY NOTE

UNLESS OTHERWISE SPECIFIED,

DIMENSIONS ARE IN INCHES.

TOLERANCES ARE:

THIS DOCUMENT CONTAINS INFORMATION

CONFIDENTIAL AND PROPRIETARY TO

.020 (2 PLCS)

'G'

SEE NOTE 12

SAMTEC, INC. AND SHALL NOT BE REPRODUCED

OR TRANSFERRED TO OTHER DOCUMENTS OR

DISCLOSED TO OTHERS OR USED FOR ANY

PURPOSE OTHER THAN THAT WHICH IT WAS

OBTAINED WITHOUT THE EXPRESSED WRITTEN

CONSENT OF SAMTEC, INC.

DECIMALS

ANGLES

.XX: .01 [.3]

520 PARK EAST BLVD, NEW ALBANY, IN 47150

PHONE: 812-944-6733 FAX: 812-948-5047

e-Mail: info@SAMTEC.com code: 55322

.050 (TYP)

.XXX: .003 [.08]

.XXXX: .0015 [.038]

SHEET SCALE: 2:1

MATERIAL:

DO NOT SCALE DRAWING

^DESCRIPTION:.100 SHROUDED CONTACT BODY

ZYTEL 103FHS, COLOR: WHITE

.096

DWG. NO.

MAX REGRIND: 25%

IPD1-XX-D-X-X

MAX FLASH ALLOWED: .005

MAX GATE VESTIGE: .004

.325

BY:

CHAD F

03/05/2002 SHEET 1 OF 4

C:\EnterpriseVault\DWG\MISC\MKTG\IPD1-XX-D-X-X-MKT.SLDDRW

REVISION U

.0187

15°

(TYP)

.0400 (TYP)

'T'

.070

+.0030

-.0000

.0895

.075±.002

.145±.002

.035

+.003

-.000

.0850

(TYP)

18°

(TYP)

.100

REF

.0305 (TYP)

+.003

-.000

.0750

(TYP)

.0297

(TYP)

.0200

R.025

DETAIL 'G'

SCALE 5 : 1

DETAIL 'D'

SCALE 5 : 1

.225±.005

.030

.0395±.0030 (TYP)

.0310 SQ (TYP)

.0800

(TYP)

.145

.085

DETAIL 'C'

SCALE 5 : 1

DETAIL 'B'

SCALE 5 : 1

DETAIL 'A'

SCALE 3 : 1

+.002

-.001

.069

34°

.0030

.005

.076

.0110

FIG. 3

IPD1-06-D-P SHOWN

30° (TYP)

.0100

+.000

-.003

(SAME AS FIG. 1, EXCEPT AS SHOWN)

.106

.0108

2° REF

"J"

.015

20°

.200

DETAIL 'T'

SCALE 10 : 1

.250

+.001

-.003

.0020

.143

.105

.1300

"J"

.4550

.006 (TYP)

.0159

R.025

30°

(TYP)

.030

.020 (TYP)

.0250±.005

.0100

15°

.255

DETAIL 'H'

.068

.041

SCALE 12 : 1

SECTION "J"-"J"

FIG. 4

(TYP)

.0735

DETAIL 'F'

SCALE 4 : 1

FIG. 5

DETAIL 'E'

SCALE 8 : 1

-K: KEYED POLARIZATION (2 POS)

( IPD1-02-D-K SHOWN)

-K: KEYED POLARIZATION

( IPD1-06-D-K SHOWN)

(SAME AS FIG. 4, UNLESS OTHERWISE STATED)

(SAME AS FIG. 1, UNLESS OTHERWISE STATED)

.015

(TYP)

.015

.0300

(TYP)

GATE PADS

(SEE NOTE 9)

"T"

"N"

02 01

PROPRIETARY NOTE

THIS DOCUMENT CONTAINS INFORMATION

CONFIDENTIAL AND PROPRIETARY TO

SAMTEC, INC. AND SHALL NOT BE REPRODUCED

OR TRANSFERRED TO OTHER DOCUMENTS OR

DISCLOSED TO OTHERS OR USED FOR ANY

PURPOSE OTHER THAN THAT WHICH IT WAS

OBTAINED WITHOUT THE EXPRESSED WRITTEN

CONSENT OF SAMTEC, INC.

520 PARK EAST BLVD, NEW ALBANY, IN 47150

PHONE: 812-944-6733

FAX: 812-948-5047

e-Mail: info@SAMTEC.com

code: 55322

DESCRIPTION:

DWG. NO.

.100 SHROUDED CONTACT BODY

"N"

2°

"T"

DO NOT SCALE DRAWING

SHEET SCALE: 2:1

2°

(TYP)

IPD1-XX-D-X-X

SECTION "N"-"N"

SCALE 4 : 1

SECTION "T"-"T"

C:\EnterpriseVault\DWG\MISC\MKTG\IPD1-XX-D-X-X-MKT.SLDDRW

BY:

CHAD F

03/05/2002 SHEET 2 OF 4

FIG. 6

(IPD1-06-D-R SHOWN)

(SAME AS FIG. 1, UNLESS OTHERWISE STATED)

(SEE NOTE 16)

.0018

REVISION U

FIG. 7

(IPD1-02-D-R SHOWN)

(SAME AS FIG. 5, UNLESS OTHERWISE STATED)

(SEE NOTE 16)

DETAIL 'S'

SCALE 8 : 1

'S'

.0400

"P"

+.000

-.001

.041

.126±.001

.325

"P"

R.055

.170

.230

.0170±.0010

SECTION "P"-"P"

SCALE 6:1

"A"

(SEE TABLE 2)

'R'

"Q"

.1600±.0010

.1700±.0010

.1800±.0010

.0085 X 45°

PROPRIETARY NOTE

THIS DOCUMENT CONTAINS INFORMATION

CONFIDENTIAL AND PROPRIETARY TO

R.005 (TYP)

SAMTEC, INC. AND SHALL NOT BE REPRODUCED

OR TRANSFERRED TO OTHER DOCUMENTS OR

DISCLOSED TO OTHERS OR USED FOR ANY

PURPOSE OTHER THAN THAT WHICH IT WAS

OBTAINED WITHOUT THE EXPRESSED WRITTEN

CONSENT OF SAMTEC, INC.

520 PARK EAST BLVD, NEW ALBANY, IN 47150

PHONE: 812-944-6733

FAX: 812-948-5047

code: 55322

.035

.040

e-Mail: info@SAMTEC.com

DESCRIPTION:

SECTION "Q"-"Q"

SCALE 6:1

DO NOT SCALE DRAWING

SHEET SCALE: 4:1

.100 SHROUDED CONTACT BODY

.065

DWG. NO.

.070

DETAIL 'R'

SCALE 20 : 1

IPD1-XX-D-X-X

C:\EnterpriseVault\DWG\MISC\MKTG\IPD1-XX-D-X-X-MKT.SLDDRW

BY:

CHAD F

03/05/2002 SHEET 3 OF 4

+.005

-.003

((No OF POSITIONS -1) x .100)

FIG. 8

REVISION U

(IPD1-06-D-G SHOWN)

(SAME AS FIG. 1, UNLESS OTHERWISE STATED)

"U"

"V"

R.01

(TYP)

"V"

.110

.060

2° (TYP)

"U"

45°

.50

SECTION "U"-"U"

SECTION "V"-"V"

SCALE 3 : 1

.310

"X"

FIG. 9

FIG. 10

(IPD1-06-D-G-R SHOWN)

(IPD1-02-D-G SHOWN)

(SAME AS FIG. 2, UNLESS OTHERWISE STATED)

(REFER TO FIG. 8 FOR -G)

(REFER TO FIG. 6 FOR -R AND FIG. 8 FOR -G)

02 01

'W'

02 01

.1000

.058

SECTION "X"-"X"

SCALE 6 : 1

.041

.068

.085

PROPRIETARY NOTE

THIS DOCUMENT CONTAINS INFORMATION

CONFIDENTIAL AND PROPRIETARY TO

SAMTEC, INC. AND SHALL NOT BE REPRODUCED

OR TRANSFERRED TO OTHER DOCUMENTS OR

DISCLOSED TO OTHERS OR USED FOR ANY

PURPOSE OTHER THAN THAT WHICH IT WAS

OBTAINED WITHOUT THE EXPRESSED WRITTEN

CONSENT OF SAMTEC, INC.

520 PARK EAST BLVD, NEW ALBANY, IN 47150

PHONE: 812-944-6733

e-Mail: info@SAMTEC.com

DESCRIPTION:

FAX: 812-948-5047

code: 55322

.0800

DO NOT SCALE DRAWING

SHEET SCALE: 3:1

.100 SHROUDED CONTACT BODY

DWG. NO.

DETAIL 'W'

SCALE 6 : 1

IPD1-XX-D-X-X

C:\EnterpriseVault\DWG\MISC\MKTG\IPD1-XX-D-X-X-MKT.SLDDRW

BY:

CHAD F

03/05/2002 SHEET 4 OF 4

IPD1-09-D-G-R [SAMTEC]

相关型号：

IPD1-09-D-P-R

IPD1-09-S

IPD1-09-S-K-R

IPD1-10-D

IPD1-10-D-K

IPD1-10-D-K-M

IPD1-10-D-KCC79L-2024-01-S

IPD1-10-D-KCC79L-2630-01-S

IPD1-10-D-KCC79R-2024-01-S

IPD1-10-D-KCC79R-2630-01-S

IPD1-10-DCC79L2024-01-S

IPD1-10-DCC79L2630-01-S