K4H281638L-LCCD [SAMSUNG]
128Mb L-die DDR SDRAM Specification; 128MB L-死DDR SDRAM规格
| 型号： | K4H281638L-LCCD |
| 厂家： | 
SAMSUNG |
| 描述： | 128Mb L-die DDR SDRAM Specification |
| 文件： | 总32页 (文件大小：485K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DDR SDRAM
K4H281638L
128Mb L-die DDR SDRAM Specification
66 TSOP-II
with Lead-Free and Halogen-Free
(RoHS compliant)
INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO SAMSUNG PRODUCTS,
AND IS SUBJECT TO CHANGE WITHOUT NOTICE. NOTHING IN THIS DOCUMENT SHALL BE
CONSTRUED AS GRANTING ANY LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHER-
WISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IN SAMSUNG PRODUCTS OR TECHNOL-
OGY. ALL INFORMATION IN THIS DOCUMENT IS PROVIDED ON AS "AS IS" BASIS WITHOUT
GUARANTEE OR WARRANTY OF ANY KIND.
1. For updates or additional information about Samsung products, contact your nearest Samsung office.
2. Samsung products are not intended for use in life support, critical care, medical, safety equipment, or similar
applications where Product failure could result in loss of life or personal or physical harm, or any military or
* Samsung Electronics reserves the right to change products or specification without notice.
Rev. 1.2 Feburary 2009
1 of 32
DDR SDRAM
K4H281638L
Table of Contents
1.0 Key Features ...............................................................................................................................4
2.0 Ordering Information ..................................................................................................................4
3.0 Operating Frequencies ...............................................................................................................4
4.0 Pin / Ball Description ..................................................................................................................5
5.0 Package Physical Dimension ....................................................................................................7
6.0 Block Diagram (2Mb x 16 I/O x4 Banks) ....................................................................................9
7.0 FUNCTIONAL DESCRIPTION ....................................................................................................10
7.1 Power-up & Initialization Sequence .............................................................................................10
7.2 Mode Register Definition ............................................................................................................11
7.3 Extended Mode Register Set(EMRS) ............................................................................................13
8.0 Input/Output Function Description .........................................................................................14
9.0 Command Truth Table ..............................................................................................................15
10.0 General Description ................................................................................................................16
11.0 Absolute Maximum Rating .....................................................................................................16
12.0 DC Operating Conditions .......................................................................................................16
13.0 DDR SDRAM Spec Items & Test Conditions ........................................................................17
14.0 Input/Output Capacitance ......................................................................................................17
15.0 Detailed test condition for DDR SDRAM IDD1 & IDD7A ......................................................18
16.0 DDR SDRAM IDD spec table ..................................................................................................19
17.0 AC Operating Conditions .......................................................................................................20
18.0 AC Overshoot/Undershoot specification for Address and Control Pins ...........................20
19.0 Overshoot/Undershoot specification for Data, Strobe and Mask Pins ..............................21
20.0 AC Timming Parameters & Specifications ...........................................................................22
21.0 System Characteristics for DDR SDRAM .............................................................................23
22.0 Component Notes ...................................................................................................................24
23.0 System Notes ..........................................................................................................................26
24.0 IBIS : I/V Characteristics for Input and Output Buffers .......................................................27
Rev. 1.2 Feburary 2009
2 of 32
DDR SDRAM
K4H281638L
Revision History
Revision
Month
Year
History
- Release rev.1.0 SPEC
- Corrected max tCK complying JEDEC
1.0
September
2008
- Changed tCK max of 400/333Mbps to 10ns from 12ns
- Corrected IDD1 current measurement condition
- Added FBGA package SPEC
- Corrected matched drive strength SPEC.
1.1
1.2
October
2008
2009
February
Rev. 1.2 Feburary 2009
3 of 32
DDR SDRAM
K4H281638L
1.0 Key Features
• VDD : 2.5V ± 0.2V, VDDQ : 2.5V ± 0.2V for DDR333, 400
• VDD : 2.5V ± 5%, VDDQ : 2.5V ± 5% for DDR500
• Double-data-rate architecture; two data transfers per clock cycle
• Bidirectional data strobe [L(U)DQS] (x16)
• Four banks operation
• Differential clock inputs(CK and CK)
• DLL aligns DQ and DQS transition with CK transition
• MRS cycle with address key programs
-. Read latency : DDR333(2.5 Clock), DDR400(3 Clock), DDR500(3 Clock)
-. Burst length (2, 4, 8)
-. Burst type (sequential & interleave)
• All inputs except data & DM are sampled at the positive going edge of the system clock(CK)
• Data I/O transactions on both edges of data strobe
• Edge aligned data output, center aligned data input
• LDM,UDM for write masking only (x16)
• Auto & Self refresh
• 15.6us refresh interval(4K/64ms refresh)
• Maximum burst refresh cycle : 8
• 66pin TSOP II Lead-Free and Halogen-Free package
• RoHS compliant
2.0 Ordering Information
Part No.
Org.
Max Freq.
Interface
Package
Note
K4H281638L-LCCD
K4H281638L-LCCC
K4H281638L-LCB3
CD(DDR500@CL=3)
CC(DDR400@CL=3)
B3(DDR333@CL=2.5)
66pin TSOP II
Lead-Free & Halogen-Free
8M x 16
SSTL2
3.0 Operating Frequencies
CD(DDR500@CL=3)
CC(DDR400@CL=3)
B3(DDR333@CL=2.5)
Speed @CL2
Speed @CL2.5
Speed @CL3
CL-tRCD-tRP
N/A
N/A
N/A
166MHz
-
166MHz
250MHz
3-4-4
166MHz
200MHz
3-3-3
2.5-3-3
Rev. 1.2 Feburary 2009
4 of 32
DDR SDRAM
K4H281638L
4.0 Pin / Ball Description
66pin TSOP - II
8Mb x 16
V
SS
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
1
V
DD
DQ15
2
DQ
0
VSSQ
3
VDDQ
DQ14
DQ13
4
DQ
1
2
5
DQ
VDDQ
6
VSSQ
DQ12
DQ11
7
DQ
3
4
8
DQ
VSSQ
9
VDDQ
DQ10
10
11
12
13
14
15
16
17
18
19
20
21
22
23
DQ
5
6
66Pin TSOPII
(400mil x 875mil)
(0.65mm Pin Pitch)
DQ
9
DQ
VDDQ
VSSQ
DQ
8
DQ
7
NC
NC
Bank Address
BA0~BA1
VSSQ
VDDQ
UDQS
NC
LDQS
NC
Auto Precharge
A10
VREF
VDD
VSS
NC
LDM
WE
UDM
CK
CK
CAS
RAS
CS
CKE
NC
24
25
26
27
28
29
30
31
32
33
NC
NC
A
A
A
A
A
A
A
11
BA
0
9
BA
1
8
AP/A10
7
A
A
A
A
0
1
2
3
6
5
4
VSS
VDD
128Mb TSOP-II Package Pinout
Organization
Row Address
Column Address
8Mx16
A0~A11
A0-A8
DM is internally loaded to match DQ and DQS identically.
Row & Column address configuration
Rev. 1.2 Feburary 2009
5 of 32
DDR SDRAM
K4H281638L
60ball FBGA (Top View)
4M x 16
9
8
7
VDDQ
DQ1
VSSQ
DQ2
B
DQ3
VDDQ
DQ4
C
DQ5
VSSQ
DQ6
DQ7
VDDQ
LDQS
E
NC
VDD
LDM
F
DQ0
VDD
CAS
WE
CS
BA0 A10/AP
A1
A2
A3
RAS
BA1
A0
VDD
A
D
G
H
J
K
L
M
3
2
1
VSS
DQ13 DQ11
DQ9
UDQS UDM
CK
CKE
A9
A7
A5
VSS
DQ15 VDDQ
VSSQ
VSSQ
VDDQ
VSSQ
DQ8
VSS
CK
NC
A11
A8
A6
A4
DQ14 DQ12 DQ10
VREF
64Mb FBGA Package ballout
Organization
4Mx16
Row Address
Column Address
A0~A11
A0-A7
DM is internally loaded to match DQ and DQS identically.
Row & Column address configuration
Rev. 1.2 Feburary 2009
6 of 32
DDR SDRAM
K4H281638L
5.0 Package Physical Dimension
Unit : mm
#66
#34
#1
#33
(1.50)
+0.075
- 0.035
0.125
22.22 ± 0.10
(10°)
0.10 MAX
[
(10°)
0.65TYP
0.075 MAX
[
(0.71)
[0.65 ± 0.08]
Detail A
Detail B
Detail B
0.25TYP
NOTE
1. ( ) IS REFERENCE
2. [ ] IS ASS’Y OUT QUALITY
Detail A
(0° ∼ 8°)
± 0.08
± 0.08
0.30
0.25
66Pin TSOP(II) Package Dimension
Rev. 1.2 Feburary 2009
7 of 32
DDR SDRAM
K4H281638L
Units : Millimeters
8.00 ± 0.10
A
#A1 MARK
0.80 x 8 = 6.40
0.80
8.0 0 ± 0.10
1.60
#A1
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
(Datum B)
G
H
J
K
L
M
0.32 ± 0.05
1.10 ± 0.10
60 - ∅ 0.45 SOLDER BALL
(Datum A)
(Post Reflow 0.50 ± 0.05)
M
A B
∅0.20
TOP VIEW
BOTTOM VIEW
60Ball FBGA 64Mb Package Dimension
Rev. 1.2 Feburary 2009
8 of 32
DDR SDRAM
K4H281638L
6.0 Block Diagram (2Mb x 16 I/O x4 Banks)
LWE
x4/8/16
CK, CK
Data Input Register
Serial to parallel
LUDM (x16)
Bank Select
x8/16/32
1Mx32
1Mx32
1Mx32
1Mx32
32
16
16
DQi
CK, CK
ADD
Column Decoder
Latency & Burst Length
Data Strobe
Programming Register
LWCBR
LCKE
LRAS LCBR
LWE
LUDM (x16)
LCAS
CK, CK
DM Input Register
LUDM (x16)
Timing Register
CK, CK
CKE
CS
RAS
CAS
WE
Rev. 1.2 Feburary 2009
9 of 32
DDR SDRAM
K4H281638L
7.0 FUNCTIONAL DESCRIPTION
7.1 Power-up & Initialization Sequence
DDR SDRAMs must be powered up and initialized in a predefined manner. Operational procedures other than those specified may
result in undefined operation. No power sequencing is specified during power up and power down given the following
•
•
•
•
•
•
•
VDD and VDDQ are driven from a single power converter output, AND
VTT is limited to 1.35 V, AND
VREF tracks VDDQ/2 OR, the following relationships must be followed:
VDDQ is driven after or with VDD such that
VDDQ < VDD + 0.3 V AND
VTT is driven after or with VDDQ such that VTT < VDDQ + 0.3 V, AND
VREF is driven after or with VDDQ such that VREF < VDDQ + 0.3 V.
At least one of these two conditions must be met.
Except for CKE, inputs are not recognized as valid until after VREF is applied. CKE is an SSTL_2 input, but will detect an LVCMOS LOW
level after VDD is applied. Maintaining an LVCMOS LOW level on CKE during power up is required to guarantee that the DQ and DQS
outputs will be in the High–Z state, where they will remain until driven in normal operation (by a read access). After all power supply and
reference voltages are stable, and the clock is stable, the DDR SDRAM requires a 200 µs delay prior to applying an executable com-
mand. Once the 200 µs delay has been satisfied, a DESELECT or NOP command should be applied, and CKE should be brought
HIGH. Following the NOP command, a PRECHARGE ALL command should be applied. Next a MODE REGISTER SET command
should be issued for the Extended Mode Register, to enable the DLL, then a MODE REGISTER SET command should be issued for the
Mode Register, to reset the DLL, and to program the operating parameters. 200 clock cycles are required between the DLL reset and
any read command. A PRECHARGE ALL command should be applied, placing the device in the ”all banks idle” state.
Once in the idle state, two AUTO refresh cycles must be performed. Additionally, a MODE REGISTER SET command for the Mode Reg-
ister, with the reset DLL bit deactivated (i.e., to program operating parameters without resetting the DLL) must be performed. Following
these cycles, the DDR SDRAM is ready for normal operation.
Rev. 1.2 Feburary 2009
10 of 32
DDR SDRAM
K4H281638L
7.2 Mode Register Definition
Mode Register Set(MRS)
The mode register stores the data for controlling the various operating modes of DDR SDRAM. It programs CAS latency, addressing
mode, burst length, test mode, DLL reset and various vendor specific options to make DDR SDRAM useful for variety of different appli-
cations. The default value of the mode register is not defined, therefore the mode register must be written after EMRS setting for proper
DDR SDRAM operation. The mode register is written by asserting low on CS, RAS, CAS, WE and BA0(The DDR SDRAM should be in
all bank precharge with CKE already high prior to writing into the mode register). The states of address pins A0 ~ A11 in the same cycle
as CS, RAS, CAS, WE and BA0 going low are written in the mode register. Two clock cycles are requested to complete the write opera-
tion in the mode register. The mode register contents can be changed using the same command and clock cycle requirements during
operation as long as all banks are in the idle state. The mode register is divided into various fields depending on functionality. The burst
length uses A0 ~ A2, addressing mode uses A3, CAS latency(read latency from column address) uses A4 ~ A6. A7 is used for test
mode. A8 is used for DLL reset. A7 must be set to low for normal MRS operation. Refer to the table for specific codes for various burst
lengths, addressing modes and CAS latencies.
BA1
BA0
0
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
Address Bus
Mode Register
RFU
RFU
DLL
TM
CAS Latency
BT
Burst Length
A8
0
1
DLL Reset
No
A7
0
1
mode
Normal
Test
A3
0
1
Burst Type
Sequential
Interleave
Yes
CAS Latency
Burst Length
BA0
0
1
An ~ A0
(Existing)MRS Cycle
Extended Funtions(EMRS)
A6
0
0
0
0
1
1
1
1
A5
0
0
1
1
0
0
1
1
A4
0
1
0
1
0
1
0
1
Latency
Reserve
Reserve
Reserve
3
Reserve
Reserve
2.5
Burst Length
A2
A1
A0
Sequential
Reserve
2
Interleave
Reserve
2
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
4
8
4
8
* RFU(Reserved for future use)
must stay "0" during MRS cycle.
Reserve
Reserve
Reserve
Reserve
Reserve
Reserve
Reserve
Reserve
Reserve
Note : *1 A12 is used for 256Mb only. That is 128Mb uses A0~A11
Rev. 1.2 Feburary 2009
11 of 32
DDR SDRAM
K4H281638L
Burst Address Ordering for Burst Length
Burst
Starting Address(A2,
Sequential Mode
Interleave Mode
Length
A1, A0)
xx0
0, 1
1, 0
0, 1
1, 0
2
xx1
x00
x01
x10
x11
000
001
010
011
100
101
110
111
0, 1, 2, 3
1, 2, 3, 0
2, 3, 0, 1
3, 0, 1, 2
0, 1, 2, 3
1, 0, 3, 2
2, 3, 0, 1
3, 2, 1, 0
4
8
0, 1, 2, 3, 4, 5, 6, 7
1, 2, 3, 4, 5, 6, 7, 0
2, 3, 4, 5, 6, 7, 0, 1
3, 4, 5, 6, 7, 0, 1, 2
4, 5, 6, 7, 0, 1, 2, 3
5, 6, 7, 0, 1, 2, 3, 4
6, 7, 0, 1, 2, 3, 4, 5
7, 0, 1, 2, 3, 4, 5, 6
0, 1, 2, 3, 4, 5, 6, 7
1, 0, 3, 2, 5, 4, 7, 6
2, 3, 0, 1, 6, 7, 4, 5
3, 2, 1, 0, 7, 6, 5, 4
4, 5, 6, 7, 0, 1, 2, 3
5, 4, 7, 6, 1, 0, 3, 2
6, 7, 4, 5, 2, 3, 0, 1
7, 6, 5, 4, 3, 2, 1, 0
Mode Register Set
0
1
2
3
4
5
6
7
8
CK
CK
*1
Mode
Register Set
Precharge
All Banks
Any
Command
Command
*2
tCK
tRP
2 Clock min.
*1 : MRS can be issued only at all bank precharge state.
*2 : Minimum tRP is required to issue MRS command.
Rev. 1.2 Feburary 2009
12 of 32
DDR SDRAM
K4H281638L
7.3 Extended Mode Register Set(EMRS)
The extended mode register stores the data for enabling or disabling DLL, and selecting output driver size. The default value of the
extended mode register is not defined, therefore the extened mode register must be written after power up for enabling or disabling DLL.
The extended mode register is written by asserting low on CS, RAS, CAS, WE and high on BA0(The DDR SDRAM should be in all bank
precharge with CKE already high prior to writing into the extended mode register). The state of address pins A0 ~ A11 and BA1 in the
same cycle as CS, RAS, CAS and WE going low are written in the extended mode register. Two clock cycles are required to complete
the write operation in the extended mode register. The mode register contents can be changed using the same command and clock
cycle requirements during operation as long as all banks are in the idle state. A0 is used for DLL enable or disable. "High" on BA0 is
used for EMRS. All the other address pins except A0, A1, A6, A11 and BA0 must be set to low for proper EMRS operation. Refer to the
table for specific codes.
Address Bus
BA1
BA0
1
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
Extended
DLL
*RFU
D.I.C
*RFU
D.I.C
*RFU
D.I.C
Mode Register
BA0
0
1
An ~ A0
MRS
EMRS
Vendor ID & Die Status Identi-
fication
A0
0
1
DLL Enable
Enable
Disable
Output Driver
A11
A6 A1
Impedence Contol
0
1
off
on
0
0
1
0
1
1
Full
Weak
Matced
*RFU : Should stay " 0" during EMRS cycle.
Figure 7. Extend Mode Register set
DLL Enable/Disable
The DLL must be enabled for normal operation. DLL enable is required during powerup initialization, and upon returning to normal
operation after having disabled the DLL for the purpose of debug or evaluation (upon exiting Self Refresh Mode, the DLL is enabled
automatically). Any time the DLL is enabled, 200 clock cycles must occur before a READ command can be issued.
Output Drive Strength
The normal drive strength for all outputs is specified to be SSTL_2, Class II. Samsung supports a weak driver strength option, intended
for lighter load and/or point-to-point environments. I-V curves for the normal drive strength and weak drive strength are included in
11.1~2 of this document.
MANUFACTURERS VENDOR CODE AND DIE STATUS IDENTIFICATION
The Manufacturers Vendor Code, V, is selected by issuing a EXTENDED MODE REGISTER SET command with bits A11 set to one,
and bits A0-A10 set to the desired values. When the V function is enabled the 128Mb DDR SDRAM will provide its manufacturers vendor
code and die status identification on DQ[1:0].
DQ[1:0]
00
Vendor ID/DSI
Samsung / Pass
Samsung / Fail
Reserved / Pass
Reserved / Fail
01
10
11
Rev. 1.2 Feburary 2009
13 of 32
DDR SDRAM
K4H281638L
8.0 Input/Output Function Description
SYMBOL
TYPE
DESCRIPTION
Clock : CK and CK are differential clock inputs. All address and control input signals are sam-
pled on the positive edge of CK and negative edge of CK. Output (read) data is referenced to
both edges of CK. Internal clock signals are derived from CK/CK.
CK, CK
Input
Clock Enable : CKE HIGH activates, and CKE LOW deactivates internal clock signals, and
device input buffers and output drivers. Taking CKE Low provides PRECHARGE POWER-
DOWN and SELF REFRESH operation (all banks idle), or ACTIVE POWER DOWN (row
ACTIVE in any bank). CKE is synchronous for POWER DOWN entry and exit, and for SELF
REFRESH entry. CKE is asynchronous for SELF REFRESH exit, and for output disable. CKE
must be maintained high throughput READ and WRITE accesses. Input buffers, excluding CK,
CK and CKE are disabled during POWER DOWN. Input buffers, excluding CKE are disabled
during SELF REFRESH. CKE is an SSTL_2 input, but will detect an LVCMOS Low level after
VDD is applied upon 1st power up, After VREF has become stable during the power on and ini-
CKE
Input
tialization sequence, it must be maintained for proper operation of the CKE receiver. For
proper SELF REFRESH entry and exit, VREF must be maintained to this input.
Chip Select : CS enables(registered LOW) and disables(registered HIGH) the command
decoder. All commands are masked when CS is registered HIGH. CS provides for external
bank selection on systems with multiple banks. CS is considered part of the command code.
CS
Input
Input
RAS, CAS, WE
Command Inputs : RAS, CAS and WE (along with CS) define the command being entered.
Input Data Mask : DM is an input mask signal for write data. Input data is masked when DM is
sampled HIGH along with that input data during a WRITE access. DM is sampled on both
edges of DQS. Although DM pins are input only, the DM loading matches the DQ and DQS
loading. For the x16, LDM corresponds to the data on DQ0~D7 ; UDM corresponds to the data
on DQ8~DQ15. DM may be driven high, low, or floating during READs.
LDM,(UDM)
BA0, BA1
Input
Input
Bank Addres Inputs : BA0 and BA1 define to which bank an ACTIVE, READ, WRITE or PRE-
CHARGE command is being applied.
Address Inputs : Provide the row address for ACTIVE commands, and the column address and
AUTO PRECHARGE bit for READ/WRITE commands, to select one location out of the mem-
ory array in the respective bank. A10 is sampled during a PRECHARGE command to deter-
mine whether the PRECHARGE applies to one bank (A10 LOW) or all banks (A10 HIGH). If
only one bank is to be precharged, the bank is selected by BA0, BA1. The address inputs also
provide the op code during a MODE REGISTER SET command. BA0 and BA1 define which
mode register is loaded during the MODE REGISTER SET command (MRS or EMRS).
A [0 : 11]
Input
DQ
I/O
I/O
Data Input/Output : Data bus
Data Strobe : Output with read data, input with write data. Edge-aligned with read data, cen-
tered in write data. Used to capture write data. For the x16, LDQS corresponds to the data on
DQ0~D7 ; UDQS corresponds to the data on DQ8~DQ15.
LDQS,(U)DQS
NC
-
No Connect : No internal electrical connection is present.
DQ Power Supply : +2.5V ± 0.2V.
DQ Ground.
VDDQ
Supply
Supply
Supply
Supply
Input
VSSQ
VDD
Power Supply : +2.5V ± 0.2V.
Ground.
VSS
VREF
SSTL_2 reference voltage.
Rev. 1.2 Feburary 2009
14 of 32
DDR SDRAM
K4H281638L
(V=Valid, X=Don′t Care, H=Logic High, L=Logic Low)
9.0 Command Truth Table
A0 ~ A9,
COMMAND
CKEn-1 CKEn CS RAS CAS
WE BA0,1 A10/AP
Note
A11
Register
Register
Extended MRS
Mode Register Set
Auto Refresh
H
H
X
X
H
L
L
L
L
L
L
L
L
L
OP CODE
OP CODE
1, 2
1, 2
3
3
3
H
L
L
L
H
X
Entry
Refresh
Self
Refresh
L
H
L
H
X
L
H
X
H
H
X
H
Exit
L
H
H
H
X
X
X
3
Bank Active & Row Addr.
Read &
Column Address
V
V
Row Address
Auto Precharge Disable
Auto Precharge Enable
Auto Precharge Disable
Auto Precharge Enable
L
H
L
4
4
4
4, 6
7
Column
Address
L
H
L
H
Write &
Column Address
Column
Address
H
H
H
X
X
X
L
L
L
H
H
L
L
H
H
L
L
L
V
H
Burst Stop
Precharge
X
Bank Selection
All Banks
V
X
L
H
X
5
H
L
X
H
L
X
V
X
X
H
X
V
X
X
H
X
V
X
X
H
X
V
X
V
X
X
H
X
V
Entry
Exit
H
L
L
H
L
Active Power Down
X
X
Entry
H
Precharge Power Down Mode
H
L
Exit
L
H
H
H
X
UDM/LDM for x16
No operation (NOP) : Not defined
Note :
X
X
8
9
9
H
L
X
H
X
H
1. OP Code : Operand Code. A0 ~ A11& BA0 ~ BA1 : Program keys. (@EMRS/MRS)
2. EMRS/MRS can be issued only at all banks precharge state.
A new command can be issued 2 clock cycles after EMRS or MRS.
3. Auto refresh functions are same as the CBR refresh of DRAM.
The automatical precharge without row precharge command is meant by "Auto".
Auto/self refresh can be issued only at all banks precharge state.
4. BA0 ~ BA1 : Bank select addresses.
If both BA0 and BA1 are "Low" at read, write, row active and precharge, bank A is selected.
If BA0 is "High" and BA1 is "Low" at read, write, row active and precharge, bank B is selected.
If BA0 is "Low" and BA1 is "High" at read, write, row active and precharge, bank C is selected.
If both BA0 and BA1 are "High" at read, write, row active and precharge, bank D is selected.
5. If A10/AP is "High" at row precharge, BA0 and BA1 are ignored and all banks are selected.
6. During burst write with auto precharge, new read/write command can not be issued.
Another bank read/write command can be issued after the end of burst.
New row active of the associated bank can be issued at tRP after the end of burst.
7. Burst stop command is valid at every burst length.
8. UDM/LDM(x16 only) sampled at the rising and falling edges of the UDQS/LDQS and Data-in are masked at the both edges
(Write UDM/LDM latency is 0).
9. This combination is not defined for any function, which means "No Operation(NOP)" in DDR SDRAM.
Rev. 1.2 Feburary 2009
15 of 32
DDR SDRAM
K4H281638L
2M x 16Bit x 4 Banks Double Data Rate SDRAM
10.0 General Description
The K4H281638L is 134,217,728 bits of double data rate synchronous DRAM organized as 4x 2,097,152 words by 16bits, fabricated
with SAMSUNG′s high performance CMOS technology. Synchronous features with Data Strobe allow extremely high performance up to
500Mb/s per pin. I/O transactions are possible on both edges of DQS. Range of operating frequencies, programmable burst length and
programmable latencies allow the device to be useful for a variety of high performance memory system applications.
11.0 Absolute Maximum Rating
Parameter
Symbol
Value
Unit
Voltage on any pin relative to VSS
VIN, VOUT
-0.5 ~ 3.6
V
Voltage on VDD & VDDQ supply relative to VSS
Storage temperature
VDD, VDDQ
TSTG
PD
1.0 ~ 3.6
V
°C
W
-55 ~ +150
Power dissipation
1
Short circuit current
IOS
50
mA
Note : Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded.
Functional operation should be restricted to recommend operation condition.
Exposure to higher than recommended voltage for extended periods of time could affect device reliability.
12.0 DC Operating Conditions
Recommended operating conditions(Voltage referenced to VSS=0V, TA=0 to 70°C)
Parameter
Symbol
VDD
Min
2.3
Max
2.7
Unit Note
Supply voltage (for device with a nominal VDD of 2.5V for DDR333, 400)
V
V
V
V
Supply voltage (for device with a nominal VDD of 2.5V for DDR500)
I/O Supply voltage (for device with a nominal VDD of 2.5V for DDR333, 400)
I/O Supply voltage (for device with a nominal VDD of 2.5V for DDR500)
VDD
VDDQ
VDDQ
VREF
VTT
2.375
2.625
2.3
2.7
2.375
2.625
0.49*VDDQ
VREF-0.04
VREF+0.15
0.51*VDDQ
VREF+0.04
VDDQ+0.3
VREF-0.15
VDDQ+0.3
VDDQ+0.6
I/O Reference voltage
V
V
1
2
I/O Termination voltage(system)
VIH(DC)
VIL(DC)
VIN(DC)
VID(DC)
VI(Ratio)
II
Input logic high voltage
V
Input logic low voltage
-0.3
-0.3
0.36
0.71
-2
V
Input Voltage Level, CK and CK inputs
Input Differential Voltage, CK and CK inputs
V-I Matching: Pullup to Pulldown Current Ratio
Input leakage current
V
V
3
4
1.4
2
-
uA
uA
mA
mA
mA
mA
mA
mA
Output leakage current
IOZ
-5
5
Output High Current(Full strengh driver) ; VOUT=VDDQ-0.388V
Output LowCurrent(Full strengh driver) ; VOUT=0.388V
Output High Current(Week strengh driver) ; VOUT=VDDQ-0.538V
Output Low Current(Week strengh driver) ; VOUT=0.538V
Output High Current(Mached strengh driver) ; VOUT=VDDQ-0.6505V
Output Low Current(Mached strengh driver) ; VOUT=0.6505V
Note :
IOH
-13.8
16.5
-18.2
20.2
-15.5
17
-16.1
19.2
-21.8
24.5
-18.9
21.3
IOL
IOH
IOL
IOH
IOL
1. VREF is expected to be equal to 0.5*VDDQ of the transmitting device, and to track variations in the dc level of same. Peak-to peak noise on VREF may
not exceed +/-2% of the dc value.
2. VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to VREF, and must track vari-
ations in the DC level of VREF
3. VID is the magnitude of the difference between the input level on CK and the input level on CK.
4. The ratio of the pullup current to the pulldown current is specified for the same temperature and voltage, over the entire temperature and voltage range,
for device drain to source voltages from 0.25V to 1.0V. For a given output, it represents the maximum difference between pullup and pulldown drivers
due to process variation. The full variation in the ratio of the maximum to minimum pullup and pulldown current will not exceed 1.7 for device drain to
source voltages from 0.1 to 1.0.
Rev. 1.2 Feburary 2009
16 of 32
DDR SDRAM
K4H281638L
13.0 DDR SDRAM Spec Items & Test Conditions
Conditions
Symbol
IDD0
Operating current - One bank Active-Precharge;
tRC=tRCmin; tCK= 6ns for DDR333, 5ns for DDR400, 4ns for DDR500;
DQ,DM and DQS inputs changing once per clock cycle;
address and control inputs changing once every two clock cycles.
Operating current - One bank operation ; One bank open, BL=4, Reads
IDD1
- Refer to the following page for detailed test condition
Precharge power-down standby current; All banks idle; power - down mode;
CKE = <VIL(max); tCK=6ns for DDR333, 5ns for DDR400, 4ns for DDR500;
IDD2P
VIN = VREF for DQ,DQS and DM.
Precharge Floating standby current; CS > =VIH(min);All banks idle; CKE > = VIH(min); tCK=6ns for DDR333, 5ns
for DDR400, 4ns for DDR500; Address and other control inputs changing once per clock cycle; VIN = VREF for
DQ,DQS and DM
Precharge Quiet standby current; CS > = VIH(min); All banks idle;
CKE > = VIH(min); tCK=6ns for DDR333, 5ns for DDR400, 4ns for DDR500; Address and other control inputs stable
at >= VIH(min) or =<VIL(max); VIN = VREF for DQ ,DQS and DM
IDD2F
IDD2Q
IDD3P
Active power - down standby current ; one bank active; power-down mode;
CKE=< VIL (max); tCK=6ns for DDR333, 5ns for DDR400, 4ns for DDR500;
VIN = VREF for DQ,DQS and DM
Active standby current; CS >= VIH(min); CKE>=VIH(min);
IDD3N
IDD4R
one bank active; active - precharge;tCK=6ns for DDR333, 5ns for DDR400, 4ns for DDR500; DQ, DQS and DM
inputs changing twice per clock cycle; address and other control inputs changing once per clock cycle
Operating current - burst read; Burst length = 2; reads; continguous burst; One bank active; address and control
inputs changing once per clock cycle; CL=2.5 at tCK=6ns for DDR333, CL=3 at tCK=5ns for DDR400, tCK=4ns for
DDR500; 50% of data changing on every transfer; lout = 0 m A
Operating current - burst write; Burst length = 2; writes; continuous burst;
One bank active address and control inputs changing once per clock cycle; CL=2.5 at tCK=6ns for DDR333, 5ns for
DDR400, tCK=4ns for DDR500; DQ, DM and DQS inputs changing twice per clock cycle, 50% of input data chang-
ing at every burst
IDD4W
Auto refresh current; tRC = tRFC(min) which is 12*tCK for DDR333 at tCK=6ns, 14*tCK for DDR400 at tCK=5ns,
IDD5
IDD6
15*tCK for DDR500 at tCK=4ns; distributed refresh
Self refresh current; CKE =< 0.2V; External clock on; tCK=6ns for DDR333, 5ns for DDR400, 4ns for DDR500.
Operating current - Four bank operation ; Four bank interleaving with BL=4
IDD7A
-Refer to the following page for detailed test condition
( TA= 25°C, f=100MHz)
14.0 Input/Output Capacitance
Parameter
Symbol
Min
Max
DeltaCap(max)
Unit
Note
Input capacitance
(A0 ~ A11, BA0 ~ BA1, CKE, CS, RAS,CAS, WE)
CIN1
1
4
0.5
pF
4
CIN2
COUT
CIN3
Input capacitance( CK, CK )
Data & DQS input/output capacitance
Input capacitance(UDM/LDM for x16)
Note :
1
1
1
5
0.25
pF
pF
pF
4
6.5
6.5
1,2,3,4
1,2,3,4
0.5
1. These values are guaranteed by design and are tested on a sample basis only.
2. Although DM is an input -only pin, the input capacitance of this pin must model the input capacitance of the DQ and DQS pins.
This is required to match signal propagation times of DQ, DQS, and DM in the system.
3. Unused pins are tied to ground.
4. This parameteer is sampled. VDDQ = +2.5V +0.2V, VDD = +2.5V+0.2V. For all devices, f=100MHz, tA=25°C, VOUT(DC) = VDDQ/2,
VOUT(peak to peak) = 0.2V. DM inputs are grouped with I/O pins - reflecting the fact that they are matched in loading (to facilitate trace matching at the
board level)
Rev. 1.2 Feburary 2009
17 of 32
DDR SDRAM
K4H281638L
15.0 Detailed test condition for DDR SDRAM IDD1 & IDD7A
IDD1 : Operating current: One bank operation
1. Typical Case: VDD = 2.5V, T=25°C
Worst Case : VDD = 2.7V, T= 10°C
2. Only one bank is accessed with tRC(min), Burst Mode, Address and Control inputs on NOP edge are changing once
per clock cycle. lout = 0mA
3. Timing patterns
- B3(166Mhz, CL=2.5) : tCK=6ns, CL=2.5, BL=4, tRCD=3*tCK, tRC = 10*tCK, tRAS=7*tCK
Read : A0 N N R0 N N N P0 N N - repeat the same timing with random address changing
*50% of data changing at every burst
- CC(200Mhz,CL = 3) : tCK = 5ns, CL = 3, BL = 4, tRCD = 3*tCK , tRC = 11*tCK, tRAS = 8*tCK
Read : A0 N N R0 N N N N P0 N N - repeat the same timing with random address changing
*50% of data changing at every transfer
- CD(250Mhz,CL = 3) : tCK = 4ns, CL = 3, BL = 4, tRCD = 4*tCK , tRC = 13*tCK, tRAS = 10*tCK
Read : A0 N N N R0 N N N N N P0 N N - repeat the same timing with random address changing
*50% of data changing at every transfer
Legend : A=Activate, R=Read, W=Write, P=Precharge, N=DESELECT
IDD7A : Operating current: Four bank operation
1. Typical Case: VDD = 2.5V, T=25°C
Worst Case : VDD = 2.7V, T= 10°C
2. Four banks are being interleaved with tRC(min), Burst Mode, Address and Control inputs on NOP edge are not
changing. lout = 0mA
4. Timing patterns
- B3(166Mhz,CL=2.5) : tCK=6ns, BL=4, tRRD=2*tCK, tRCD=3*tCK, tRAS=5*tCK
Read : A0 N A1 RA0 A2 RA1 A3 RA2 N RA3 - repeat the same timing with random address changing
*50% of data changing at every burst
- CC(200Mhz,CL = 3) : tCK = 5ns, BL = 4, tRRD=2*tCK, tRCD = 3*tCK , tRAS = 8*tCK
Read : A0 N A1 RA0 A2 RA1 A3 RA2 N RA3 - repeat the same timing with random address changing
*50% of data changing at every transfer
- CD(250Mhz,CL = 3) : tCK = 4ns, CL = 3, BL = 4, tRCD = 4*tCK , tRAS = 10*tCK
Read : A0 N N A1 RA0 A2 RA1 A3 RA2 N RA3 - repeat the same timing with random address changing
*50% of data changing at every transfer
Legend : A=Activate, R=Read, W=Write, P=Precharge, N=DESELECT
Rev. 1.2 Feburary 2009
18 of 32
DDR SDRAM
K4H281638L
16.0 DDR SDRAM IDD spec table
(VDD=2.7V, T = 10°C)
8Mx16 (K4H281638L)
Symbol
Unit
CD(DDR500@CL=3)
CC(DDR400@CL=3)
B3(DDR333@CL=2.5)
IDD0
IDD1
120
110
120
8
100
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
130
120
IDD2P
IDD2F
IDD2Q
IDD3P
IDD3N
IDD4R
IDD4W
IDD5
40
40
40
40
40
40
40
35
35
55
55
55
200
200
200
3
180
180
180
3
160
160
160
3
IDD6
Normal
IDD7A
300
300
280
Rev. 1.2 Feburary 2009
19 of 32
DDR SDRAM
K4H281638L
17.0 AC Operating Conditions
Parameter/Condition
Symbol
VIH(AC)
Min
VREF + 0.31
Max
Unit
V
Note
Input High (Logic 1) Voltage, DQ, DQS and DM signals
Input Low (Logic 0) Voltage, DQ, DQS and DM signals.
Input Differential Voltage, CK and CK inputs
Input Crossing Point Voltage, CK and CK inputs
I/O Reference Voltage
VIL(AC)
VID(AC)
VIX(AC)
VREF - 0.31
VDDQ+0.6
V
0.7
V
1
2
3
0.5*VDDQ-0.2
0.45 x VDDQ
0.5*VDDQ+0.2
0.55 x VDDQ
V
VREF(AC)
V
Note :
1. VID is the magnitude of the difference between the input level on CK and the input level on CK.
2. The value of VIX is expected to equal 0.5*VDDQ of the transmitting device and must track variations in the dc level of the same.
3. VREF is expected to equal VDDQ/2 of the transmitting device and to track variations in the DC level of the same.
Peak-to-peak noise (non-common mode) on VREF may not exceed ±2 percent of the DC value. Thus, from VDDQ/2, VREF is allowed ± 25mV for
DC error and an additional ± 25mV for AC noise. This measurement is to be taken at the nearest VREF by-pass capacitor.
18.0 AC Overshoot/Undershoot specification for Address and Control Pins
Specification
Parameter
DDR400
1.5 V
DDR333
1.5 V
Maximum peak amplitude allowed for overshoot
Maximum peak amplitude allowed for undershoot
1.5 V
1.5 V
The area between the overshoot signal and VDD must be less than or equal to
4.5 V-ns
4.5 V-ns
4.5 V-ns
4.5 V-ns
The area between the undershoot signal and GND must be less than or equal to
V
DD
Overshoot
Area
5
4
Maximum Amplitude = 1.5V
3
2
1
0
-1
-2
-3
-4
-5
Maximum Amplitude = 1.5V
GND
0
0.6875
0.5 1.0
1.5
2.5
3.5
4.5
5.5
6.3125
6.0 6.5
undershoot
7.0
2.0
3.0
4.0
5.0
Tims(ns)
AC overshoot/Undershoot Definition
Rev. 1.2 Feburary 2009
20 of 32
DDR SDRAM
K4H281638L
19.0 Overshoot/Undershoot specification for Data, Strobe and Mask Pins
Specification
Parameter
DDR400
1.2 V
DDR333
1.2 V
Maximum peak amplitude allowed for overshoot
Maximum peak amplitude allowed for undershoot
1.2 V
1.2 V
The area between the overshoot signal and VDD must be less than or equal to
2.4 V-ns
2.4 V-ns
2.4 V-ns
2.4 V-ns
The area between the undershoot signal and GND must be less than or equal to
V
DDQ
Overshoot
5
4
Maximum Amplitude = 1.2V
3
2
Area
1
0
-1
-2
-3
-4
-5
Maximum Amplitude = 1.2V
GND
0
0.5 1.0 1.42 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 5.68 6.0 6.5 7.0
Tims(ns)
undershoot
DQ/DM/DQS AC overshoot/Undershoot Definition
Rev. 1.2 Feburary 2009
21 of 32
DDR SDRAM
K4H281638L
20.0 AC Timming Parameters & Specifications
CD
CC
B3
(DDR333@CL=2.5)
(DDR500@CL=3.0)
(DDR400@CL=3.0)
Parameter
Symbol
Unit
Note
Min
52
Max
-
Min
55
Max
-
Min
60
Max
-
Row cycle time
tRC
tRFC
tRAS
tRCD
tRP
ns
ns
ns
ns
ns
ns
ns
tCK
ns
Refresh row cycle time
Row active time
60
-
70
-
72
-
36
70K
40
70K
42
70K
RAS to CAS delay
16
-
15
-
18
-
Row precharge time
Row active to Row active delay
Write recovery time
16
-
15
-
18
-
tRRD
tWR
12
-
10
-
12
-
12
-
15
-
15
-
Last data in to Read command
Clock cycle time
tWTR
tCK
2
-
2
-
1
-
CL=2.5
CL=3.0
6
10
6
10
6
10
4
8
5
8
-
-
Clock high level width
tCH
tCL
0.45
0.45
-0.6
-0.6
-
0.55
0.45
0.45
-0.6
-0.7
-
0.55
0.45
0.45
-0.6
-0.7
-
0.55
tCK
tCK
ns
Clock low level width
0.55
0.55
0.55
DQS-out access time from CK/CK
Output data access time from CK/CK
Data strobe edge to ouput data edge
Read Preamble
tDQSCK
tAC
+0.6
+0.6
+0.6
+0.6
+0.7
+0.7
ns
TSOP
tDQSQ
tRPRE
tRPST
tDQSS
tWPRES
tWPREH
tDSS
tDSH
tDQSH
tDQSL
tIS
0.4
0.4
0.45
ns
22
13
0.9
0.4
0.85
0
1.1
0.9
0.4
0.72
0
1.1
0.9
0.4
0.75
0
1.1
tCK
tCK
tCK
ns
Read Postamble
0.6
0.6
0.6
CK to valid DQS-in
1.15
1.28
1.25
DQS-in setup time
-
-
-
DQS-in hold time
0.35
0.2
0.2
0.4
0.4
0.9
0.9
0.9
0.9
-0.7
-0.7
8
-
0.25
0.2
0.2
0.35
0.35
0.6
0.6
0.7
0.7
-0.65
-0.65
10
-
0.25
0.2
0.2
0.35
0.35
0.75
0.75
0.8
0.8
-0.7
-0.7
12
-
tCK
tCK
tCK
tCK
tCK
ns
DQS falling edge to CK rising-setup time
-
-
-
DQS falling edge from CK rising-hold time
DQS-in high level width
-
-
-
-
-
-
DQS-in low level width
-
-
-
15, 17~19
15, 17~19
16~19
16~19
11
Address and Control Input setup time(fast)
Address and Control Input hold time(fast)
-
-
-
tIH
-
-
-
ns
Address and Control Input setup time(slow)
Address and Control Input hold time(slow)
Data-out high impedence time from CK/CK
Data-out low impedence time from CK /CK
Mode register set cycle time
tIS
-
-
-
ns
tIH
-
+0.7
+0.7
-
-
-
+0.7
+0.7
-
ns
tHZ
+0.65
ns
tLZ
+0.65
ns
11
tMRD
tDS
-
-
ns
DQ & DM setup time to DQS
0.4
-
0.4
0.45
-
ns
j, k
j, k
ns
DQ & DM hold time to DQS
tDH
0.4
-
0.4
-
0.45
-
Control & Address input pulse width
DQ & DM input pulse width
tIPW
tDIPW
tXSNR
tXSRD
tREFI
2.2
1.75
75
-
2.2
1.75
75
-
2.2
1.75
75
-
ns
ns
18
18
-
-
-
Exit self refresh to non-Read command
Exit self refresh to read command
Refresh interval time
-
-
-
-
-
-
ns
200
200
200
tCK
us
15.6
15.6
15.6
14
21
tHP
-tQHS
tHP
-tQHS
tHP
-tQHS
Output DQS valid window
Clock half period
tQH
tHP
-
-
-
-
-
-
ns
ns
tCLmin
or tCHmin
tCLmin
or tCHmin
tCLmin
or tCHmin
20, 21
Data hold skew factor
TSOP
tQHS
0.4
0.6
0.5
0.6
0.55
0.6
ns
21
12
DQS write postamble time
tWPST
0.4
16
0.4
15
0.4
18
tCK
Active to Read with Auto precharge
command
tRAP
-
-
-
(tWR/tCK)
+
(tRP/tCK)
(tWR/tCK)
+
(tRP/tCK)
(tWR/tCK)
+
(tRP/tCK)
Autoprecharge write recovery +
Precharge time
tDAL
-
-
-
-
-
-
tCK
tCK
23
Power Down Exit
tPDEX
1
1
1
Rev. 1.2 Feburary 2009
22 of 32
DDR SDRAM
K4H281638L
21.0 System Characteristics for DDR SDRAM
The following specification parameters are required in systems using DDR400 and DDR333 devices to ensure proper system perfor-
mance. these characteristics are for system simulation purposes and are guaranteed by design.
Table 1 : Input Slew Rate for DQ, DQS, and DM
AC CHARACTERISTICS
DDR400
DDR333
SYMBOL
Units
Notes
PARAMETER
MIN
MAX
MIN
MAX
DQ/DM/DQS input slew rate measured between
VIH(DC), VIL(DC) and VIL(DC), VIH(DC)
DCSLEW
0.5
4.0
0.5
4.0
V/ns
a, l
Table 2 : Input Setup & Hold Time Derating for Slew Rate
Input Slew Rate
∆tIS
∆tIH
Units
Notes
0.5 V/ns
0
0
0
0
ps
i
i
i
0.4 V/ns
+50
+100
ps
0.3 V/ns
ps
Table 3 : Input/Output Setup & Hold Time Derating for Slew Rate
Input Slew Rate
∆tDS
∆tDH
Units
Notes
0.5 V/ns
0
0
ps
k
k
k
0.4 V/ns
+75
+150
+75
+150
ps
0.3 V/ns
ps
Table 4 : Input/Output Setup & Hold Derating for Rise/Fall Delta Slew Rate
Delta Slew Rate
∆tDS
∆tDH
Units
Notes
+/- 0.0 V/ns
0
0
ps
j
j
j
+/- 0.25 V/ns
+/- 0.5 V/ns
+50
+100
+50
+100
ps
ps
Table 5 : Output Slew Rate Characteristice (X4, X8 Devices only)
Typical Range
Minimum
Maximum
Slew Rate Characteristic
Notes
(V/ns)
(V/ns)
(V/ns)
Pullup Slew Rate
Pulldown slew
1.2 ~ 2.5
1.2 ~ 2.5
1.0
1.0
4.5
4.5
a,c,d,f,g,h
b,c,d,f,g,h
Table 6 : Output Slew Rate Characteristice (X16 Devices only)
Typical Range
Minimum
Maximum
Slew Rate Characteristic
Notes
(V/ns)
(V/ns)
(V/ns)
Pullup Slew Rate
Pulldown slew
1.2 ~ 2.5
1.2 ~ 2.5
0.7
0.7
5.0
5.0
a,c,d,f,g,h
b,c,d,f,g,h
Table 7 : Output Slew Rate Matching Ratio Characteristics
AC CHARACTERISTICS
PARAMETER
Output Slew Rate Matching Ratio (Pullup to Pulldown)
DDR400
DDR333
Notes
e, l
MIN
0.67
MAX
1.5
MIN
0.67
MAX
1.5
Rev. 1.2 Feburary 2009
23 of 32
DDR SDRAM
K4H281638L
22.0 Component Notes
1. All voltages referenced to VSS
.
2. Tests for ac timing, IDD, and electrical, ac and dc characteristics, may be conducted at nominal reference/supply voltage levels,
but the related specifications and device operation are guaranteed for the full voltage range specified.
3. Figure 1 represents the timing reference load used in defining the relevant timing parameters of the part. It is not intended to be
either a precise representation of the typical system environment nor a depiction of the actual load presented by a production
tester. System designers will use IBIS or other simulation tools to correlate the timing reference load to a system environment.
Manufacturers will correlate to their production test conditions (generally a coaxial transmission line terminated at the tester elec-
tronics).
VTT
50Ω
Output
(Vout)
30pF
Figure 1 : Timing Reference Load
4. AC timing and IDD tests may use a VIL to VIH swing of up to 1.5 V in the test environment, but input timing is still referenced to
VREF (or to the crossing point for CK/CK), and parameter specifications are guaranteed for the specified ac input levels under nor-
mal use conditions. The minimum slew rate for the input signals is 1 V/ns in the range between VIL(AC) and VIH(AC).
5. The ac and dc input level specifications are as defined in the SSTL_2 Standard (i.e., the receiver will effectively switch as a result
of the signal crossing the ac input level and will remain in that state as long as the signal does not ring back above (below) the dc
input LOW (HIGH) level.
6. Inputs are not recognized as valid until VREF stabilizes. Exception: during the period before VREF stabilizes, CKE ≤ 0.2VDDQ is
recognized as LOW.
7. Enables on.chip refresh and address counters.
8. IDD specifications are tested after the device is properly initialized.
9. The CK/CK input reference level (for timing referenced to CK/CK) is the point at which CK and CK cross; the input reference level
for signals other than CK/CK, is VREF
.
10. The output timing reference voltage level is VTT.
11. tHZ and tLZ transitions occur in the same access time windows as valid data transitions. These parameters are not referenced to
a specific voltage level but specify when the device output is no longer driving (HZ), or begins driving (LZ).
12. The maximum limit for this parameter is not a device limit. The device will operate with a greater value for this parameter, but sys
tem performance (bus turnaround) will degrade accordingly.
13. The specific requirement is that DQS be valid (HIGH, LOW, or at some point on a valid transition) on or before this CK edge. A
valid transition is defined as monotonic and meeting the input slew rate specifications of the device. when no writes were previ
ously in progress on the bus, DQS will be transitioning from High- Z to logic LOW. If a previous write was in progress, DQS could
be HIGH, LOW, or transitioning from HIGH to LOW at this time, depending on tDQSS.
14. A maximum of eight AUTO REFRESH commands can be posted to any given DDR SDRAM device.
15. For command/address input slew rate ≥ 1.0 V/ns
16. For command/address input slew rate ≥ 0.5 V/ns and < 1.0 V/ns
Rev. 1.2 Feburary 2009
24 of 32
DDR SDRAM
K4H281638L
Component Notes
17. For CK & CK slew rate ≥ 1.0 V/ns
18. These parameters guarantee device timing, but they are not necessarily tested on each device. They may be guaranteed by
device design or tester correlation.
19. Slew Rate is measured between VOH(AC) and VOL(AC).
20. Min (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this
value can be greater than the minimum specification limits for tCL and tCH).....For example, tCL and tCH are = 50% of the
period, less the half period jitter (tJIT(HP)) of the clock source, and less the half period jitter due to crosstalk (tJIT(crosstalk)) into
the clock traces.
21. tQH = tHP - tQHS, where:
tHP = minimum half clock period for any given cycle and is defined by clock high or clock low (tCH, tCL). tQHS accounts for 1) The
pulse duration distortion of on-chip clock circuits; and 2) The worst case push-out of DQS on one tansition followed by the worst
case pull-in of DQ on the next transition, both of which are, separately, due to data pin skew and output pattern effects, and p-
channel to n-channel variation of the output drivers.
22. tDQSQ
Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers for any given cycle.
23. tDAL = (tWR/tCK) + (tRP/tCK)
For each of the terms above, if not already an integer, round to the next highest integer. Example: For DDR400 at CL=3 and
tCK=5ns tDAL = (15 ns / 5 ns) + (15 ns/ 5 ns) = (3) + (3)
tDAL = 6 clocks
Rev. 1.2 Feburary 2009
25 of 32
DDR SDRAM
K4H281638L
23.0 System Notes
a. Pullup slew rate is characteristized under the test conditions as shown in Figure 2.
Test point
Output
50Ω
VSSQ
Figure 2 : Pullup slew rate test load
b. Pulldown slew rate is measured under the test conditions shown in Figure 3.
VDDQ
50Ω
Output
Test point
Figure 3 : Pulldown slew rate test load
c. Pullup slew rate is measured between (VDDQ/2 - 320 mV +/- 250 mV)
Pulldown slew rate is measured between (VDDQ/2 + 320 mV +/- 250 mV)
Pullup and Pulldown slew rate conditions are to be met for any pattern of data, including all outputs switching and only one output
switching.
Example : For typical slew rate, DQ0 is switching
For minmum slew rate, all DQ bits are switching from either high to low, or low to high.
The remaining DQ bits remain the same as for previous state.
d. Evaluation conditions
Typical : 25 °C (T Ambient), VDDQ = 2.5V, typical process
Minimum : 70 °C (T Ambient), VDDQ = 2.3V, slow - slow process
Maximum : 0 °C (T Ambient), VDDQ = 2.7V, fast - fast process
e. The ratio of pullup slew rate to pulldown slew rate is specified for the same temperature and voltage, over the entire temperature and
voltage range. For a given output, it represents the maximum difference between pullup and pulldown drivers due to process variation.
f. Verified under typical conditions for qualification purposes.
g. TSOPII package divices only.
h. Only intended for operation up to 500 Mbps per pin.
i. A derating factor will be used to increase tIS and tIH in the case where the input slew rate is below 0.5V/ns
as shown in Table 2. The Input slew rate is based on the lesser of the slew rates detemined by either VIH(AC) to VIL(AC) or
VIH(DC) to VIL(DC), similarly for rising transitions.
j. A derating factor will be used to increase tDS and tDH in the case where DQ, DM, and DQS slew rates differ, as shown in Tables 3 & 4.
Input slew rate is based on the larger of AC-AC delta rise, fall rate and DC-DC delta rise, Input slew rate is based on the lesser of the
slew rates determined by either VIH(AC) to VIL(AC) or VIH(DC) to VIL(DC), similarly for rising transitions.
The delta rise/fall rate is calculated as:
{1/(Slew Rate1)} - {1/(Slew Rate2)}
For example : If Slew Rate 1 is 0.5 V/ns and slew Rate 2 is 0.4 V/ns, then the delta rise, fall rate is - 0.5ns/V . Using the table given, this
would result in the need for an increase in tDS and tDH of 100 ps.
k. Table 3 is used to increase tDS and tDH in the case where the I/O slew rate is below 0.5 V/ns. The I/O slew rate is based on the lesser
on the lesser of the AC - AC slew rate and the DC- DC slew rate. The inut slew rate is based on the lesser of the slew rates deter
mined by either VIH(AC) to VIL(AC) or VIH(DC) to VIL(DC), and similarly for rising transitions.
l. DQS, DM, and DQ input slew rate is specified to prevent double clocking of data and preserve setup and hold times. Signal transi
tions through the DC region must be monotonic.
Rev. 1.2 Feburary 2009
26 of 32
DDR SDRAM
K4H281638L
24.0 IBIS : I/V Characteristics for Input and Output Buffers
DDR SDRAM Output Driver V-I Characteristics
DDR SDRAM Output driver characteristics are defined for full and half strength operation as selected by the EMRS bit A1.
Figures 4, 5 and 6 show the driver characteristics graphically, and tables 8, 9 and 10 show the same data in tabular format suitable for
input into simulation tools. The driver characteristcs evaluation conditions are:
Typical
Minimum
Maximum
25×C
70×C
0×C
VDD/VDDQ = 2.5V, typical process
VDD DDQ
/V
= 2.3V, slow-slow process
= 2.7V, fast-fast process
VDD/VDDQ
Output Driver Characteristic Curves Notes:
1. The full variation in driver current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines
the of the V-I curve of Figures 4, 5 and 6.
2. It is recommended that the "typical" IBIS V-I curve lie within the inner bounding lines of the V-I curves of Figures 4, 5 and 6.
3. The full variation in the ratio of the "typical" IBIS pullup to "typical" IBIS pulldown current should be unity +/- 10%, for device drain to
source voltages from 0.1 to1.0. This specification is a design objective only. It is not guaranteed.
160
Maximum
140
120
100
80
Typical High
Typical Low
Minimum
60
40
20
0
0.0
0.5
1.0
1.5
2.0
2.5
Vout(V)
Pull-down Characteristics for Full Strength Output Driver
0.0
1.0
2.0
0
-20
-40
Minumum
-60
-80
Typical Low
-100
-120
-140
-160
-180
-200
-220
Typical High
Maximum
Vout(V)
Pull-up Characteristics for Full Strength Output Driver
Figure 4. I/V characteristics for input/output buffers:Pulldown(above) and pullup(below)
Rev. 1.2 Feburary 2009
27 of 32
DDR SDRAM
K4H281638L
Pull-down Current (mA)
Pull-up Current (mA)
Voltage
(V)
Typical
Low
Typical
Minimum
High
Typical
Low
Typical
High
Maximum
Minimum
Maximum
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
6.0
6.8
13.5
20.1
26.6
33.0
39.1
44.2
49.8
55.2
60.3
65.2
69.9
74.2
78.4
82.3
85.9
89.1
92.2
95.3
97.2
99.1
100.9
101.9
102.8
103.8
104.6
105.4
4.6
9.2
9.6
18.2
26.0
33.9
41.8
49.4
56.8
63.2
69.9
76.3
82.5
88.3
93.8
99.1
103.8
108.4
112.1
115.9
119.6
123.3
126.5
129.5
132.4
135.0
137.3
139.2
140.8
-6.1
-7.6
-14.5
-21.2
-27.7
-34.1
-40.5
-46.9
-53.1
-59.4
-65.5
-71.6
-77.6
-83.6
-89.7
-95.5
-101.3
-107.1
-112.4
-118.7
-124.0
-129.3
-134.6
-139.9
-145.2
-150.5
-155.3
-160.1
-4.6
-9.2
-10.0
-20.0
-29.8
-38.8
-46.8
-54.4
-61.8
-69.5
-77.3
12.2
18.1
24.1
29.8
34.6
39.4
43.7
47.5
51.3
54.1
56.2
57.9
59.3
60.1
60.5
61.0
61.5
62.0
62.5
62.9
63.3
63.8
64.1
64.6
64.8
65.0
-12.2
-18.1
-24.0
-29.8
-34.3
-38.1
-41.1
-41.8
-46.0
-47.8
-49.2
-50.0
-50.5
-50.7
-51.0
-51.1
-51.3
-51.5
-51.6
-51.8
-52.0
-52.2
-52.3
-52.5
-52.7
-52.8
13.8
18.4
23.0
27.7
32.2
36.8
39.6
42.6
44.8
46.2
47.1
47.4
47.7
48.0
48.4
48.9
49.1
49.4
49.6
49.8
49.9
50.0
50.2
50.4
50.5
-13.8
-18.4
-23.0
-27.7
-32.2
-36.0
-38.2
-38.7
-39.0
-39.2
-39.4
-39.6
-39.9
-40.1
-40.2
-40.3
-40.4
-40.5
-40.6
-40.7
-40.8
-40.9
-41.0
-41.1
-41.2
-85.2
-93.0
-100.6
-108.1
-115.5
-123.0
-130.4
-136.7
-144.2
-150.5
-156.9
-163.2
-169.6
-176.0
-181.3
-187.6
-192.9
-198.2
Table 8. Full Strength Driver Characteristics
Rev. 1.2 Feburary 2009
28 of 32
DDR SDRAM
K4H281638L
90
80
70
60
50
40
30
20
10
Maximum
Typical High
Typical Low
Minimum
0
0.0
1.0
2.0
Vout(V)
Pull-down Characteristics for Weak Output Driver
0.0
1.0
2.0
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
Minumum
Typical Low
Typical High
Maximum
Vout(V)
Pull-up Characteristics for Weak Output Driver
Figure 5. I/V characteristics for input/output buffers:Pulldown(above) and pullup(below)
Rev. 1.2 Feburary 2009
29 of 32
DDR SDRAM
K4H281638L
Pull-down Current (mA)
Pull-up Current (mA)
Voltage
(V)
Typical
Low
Typical
Minimum
High
Typical
Low
Typical
High
Maximum
Minimum
Maximum
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
3.4
6.9
3.8
7.6
2.6
5.2
7.8
5.0
9.9
-3.5
-6.9
-4.3
-8.2
-2.6
-5.2
-7.8
-5.0
-9.9
10.3
13.6
16.9
19.6
22.3
24.7
26.9
29.0
30.6
31.8
32.8
33.5
34.0
34.3
34.5
34.8
35.1
35.4
35.6
35.8
36.1
36.3
36.5
36.7
36.8
11.4
15.1
18.7
22.1
25.0
28.2
31.3
34.1
36.9
39.5
42.0
44.4
46.6
48.6
50.5
52.2
53.9
55.0
56.1
57.1
57.7
58.2
58.7
59.2
59.6
14.6
19.2
23.6
28.0
32.2
35.8
39.5
43.2
46.7
50.0
53.1
56.1
58.7
61.4
63.5
65.6
67.7
69.8
71.6
73.3
74.9
76.4
77.7
78.8
79.7
-10.3
-13.6
-16.9
-19.4
-21.5
-23.3
-24.8
-26.0
-27.1
-27.8
-28.3
-28.6
-28.7
-28.9
-28.9
-29.0
-29.2
-29.2
-29.3
-29.5
-29.5
-29.6
-29.7
-29.8
-29.9
-12.0
-15.7
-19.3
-22.9
-26.5
-30.1
-33.6
-37.1
-40.3
-43.1
-45.8
-48.4
-50.7
-52.9
-55.0
-56.8
-58.7
-60.0
-61.2
-62.4
-63.1
-63.8
-64.4
-65.1
-65.8
-14.6
-19.2
-23.6
-28.0
-32.2
-35.8
-39.5
-43.2
-46.7
-50.0
-53.1
-56.1
-58.7
-61.4
-63.5
-65.6
-67.7
-69.8
-71.6
-73.3
-74.9
-76.4
-77.7
-78.8
-79.7
10.4
13.0
15.7
18.2
20.8
22.4
24.1
25.4
26.2
26.6
26.8
27.0
27.2
27.4
27.7
27.8
28.0
28.1
28.2
28.3
28.3
28.4
28.5
28.6
-10.4
-13.0
-15.7
-18.2
-20.4
-21.6
-21.9
-22.1
-22.2
-22.3
-22.4
-22.6
-22.7
-22.7
-22.8
-22.9
-22.9
-23.0
-23.0
-23.1
-23.2
-23.2
-23.3
-23.3
Table 9. Weak Driver Characteristics
Rev. 1.2 Feburary 2009
30 of 32
DDR SDRAM
K4H281638L
70
60
50
40
30
20
10
Maximum
Minimum
0
0.0
1.0
2.0
Vout(V)
Pull-down Characteristics for Matched Output Driver
0.0
0
1.0
2.0
-10
-20
-30
-40
-50
-60
-70
Minumum
Maximum
Vout(V)
Pull-up Characteristics for Matched Output Driver
Figure 6. I/V characteristics for input/output buffers:Pulldown(above) and pullup(below)
Rev. 1.2 Feburary 2009
31 of 32
DDR SDRAM
K4H281638L
Pull-down Current(mA)
Minimum Maximum
pull-up Current (mA)
Voltage
Minimum
Maximum
(V)
0
0.0
3.6
0.0
7.8
0.0
-4.4
-8.8
0.0
-8.8
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
2.2
7.3
15.8
23.1
29.4
35.5
41.0
46.1
50.5
53.8
57.3
60.1
-15.7
-23.0
-29.4
-35.4
-41.0
-46.0
-50.3
-53.8
-57.2
-60.1
11.0
14.6
16.8
18.3
18.8
19.0
19.6
19.7
19.8
-13.3
-17.3
-18.6
-18.9
-19.0
-19.3
-19.5
-19.6
-19.7
Table 10. Matched Driver Characteristics
Rev. 1.2 Feburary 2009
32 of 32
相关型号：
K4H281638L-LCCD0
DDR DRAM, 8MX16, 0.6ns, CMOS, PDSO66, 0.400 X 0.875 INCH, 0.65 MM PITCH, HALOGEN FREE AND ROHS COMPLIANT, TSOP2-66
SAMSUNG
©2020 ICPDF网 联系我们和版权申明