K4B1G1646E-HCH9 [SAMSUNG]
DDR DRAM, 64MX16, 0.125ns, CMOS, PBGA96,;型号: | K4B1G1646E-HCH9 |
厂家: | SAMSUNG |
描述: | DDR DRAM, 64MX16, 0.125ns, CMOS, PBGA96, 时钟 动态存储器 双倍数据速率 内存集成电路 |
文件: | 总61页 (文件大小:1129K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
1Gb E-die DDR3 SDRAM Specification
78 / 96 FBGA with Lead-Free & Halogen-Free
(RoHS Compliant)
INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO SAMSUNG PRODUCTS,
AND IS SUBJECT TO CHANGE WITHOUT NOTICE. NOTHING IN THIS DOCUMENT SHALL BE
CONSTRUED AS GRANTING ANY LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHER-
WISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IN SAMSUNG PRODUCTS OR TECHNOL-
OGY. ALL INFORMATION IN THIS DOCUMENT IS PROVIDED ON AS "AS IS" BASIS WITHOUT
GUARANTEE OR WARRANTY OF ANY KIND.
1. For updates or additional information about Samsung products, contact your nearest Samsung office.
2. Samsung products are not intended for use in life support, critical care, medical, safety equipment, or similar
applications where Product failure could result in loss of life or personal or physical harm, or any military or
defense application, or any governmental procurement to which special terms or provisions may apply.
* Samsung Electronics reserves the right to change products or specification without notice.
Rev. 1.0 February 2009
Page 1 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
Revision History
Revision
Month
Year
History
1.0
February
2009
- First release
Rev. 1.0 February 2009
Page 2 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
Table Contents
1.0 Ordering Information .................................................................................................................. 5
2.0 Key Features ................................................................................................................................ 5
3.0 Package pinout/Mechanical Dimension & Addressing ............................................................ 6
3.1 x4 Package Pinout (Top view) : 78ball FBGA Package ...................................................................... 6
3.2 x8 Package Pinout (Top view) : 78ball FBGA Package ...................................................................... 7
3.3 x16 Package Pinout (Top view) : 96ball FBGA Package .................................................................... 8
3.4 FBGA Package Dimension (x4/x8) ................................................................................................. 9
3.5 FBGA Package Dimension (x16) .................................................................................................. 10
4.0 Input/Output Functional Description ....................................................................................... 11
5.0 DDR3 SDRAM Addressing ........................................................................................................ 12
6.0 Absolute Maximum Ratings ...................................................................................................... 13
6.1 Absolute Maximum DC Ratings ................................................................................................... 13
6.2 DRAM Component Operating Temperature Range ......................................................................... 13
7.0 AC & DC Operating Conditions ................................................................................................ 13
7.1 Recommended DC operating Conditions (SSTL_1.5) ..................................................................... 13
8.0 AC & DC Input Measurement Levels ........................................................................................ 14
8.1 AC & DC Logic input levels for single-ended signals ..................................................................... 14
8.2 V
Tolerances ........................................................................................................................ 15
REF
8.3 AC & DC Logic Input Levels for Differential Signals ...................................................................... 16
8.3.1 Differential signals definition ............................................................................................... 16
8.3.2 Differential swing requirement for clock (CK - CK) and strobe (DQS - DQS) ............................... 16
8.3.3 Single-ended requirements for differential signals .................................................................. 17
8.4 Differential Input Cross Point Voltage .......................................................................................... 18
8.5 Slew rate definition for Differential Input Signals ........................................................................... 18
8.6 Slew rate definition for Differential Input Signals ........................................................................... 18
9.0 AC & DC Output Measurement Levels ..................................................................................... 19
9.1 Single-ended AC & DC Output Levels .......................................................................................... 19
9.2 Differential AC & DC Output Levels ............................................................................................. 19
9.3 Single-ended Output Slew Rate ................................................................................................... 19
9.4 Differential Output Slew Rate ...................................................................................................... 20
9.5 Reference Load for AC Timing and Output Slew Rate .................................................................... 20
9.6 Overshoot/Undershoot Specification ........................................................................................... 21
9.6.1 Address and Control Overshoot and Undershoot specifications .............................................. 21
9.6.2 Clock, Data, Strobe and Mask Overshoot and Undershoot Specifications ................................. 21
9.7 34ohm Output Driver DC Electrical Characteristics ....................................................................... 22
9.7.1 Output Drive Temperature and Voltage Sensitivity .................................................................. 23
9.8 On-Die Termination (ODT) Levels and I-V Characteristics ............................................................... 23
9.8.1 ODT DC Electrical Characteristics ........................................................................................ 24
9.8.2 ODT Temperature and Voltage sensitivity .............................................................................. 25
9.9 ODT Timing Definitions .............................................................................................................. 26
9.9.1 Test Load for ODT Timings .................................................................................................. 26
9.9.2 ODT Timing Definitions ....................................................................................................... 26
10.0 IDD Specification Parameters and Test Conditions ............................................................. 29
10.1 IDD Measurement Conditions .................................................................................................... 29
Rev. 1.0 February 2009
Page 3 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
11.0 1Gb DDR3 SDRAM E-die IDD Specification Table ................................................................ 38
12.0 Input/Output Capacitance ....................................................................................................... 40
13.0 Electrical Characteristics and AC timing for DDR3-800 to DDR3-1600 .............................. 41
13.1 Clock Specification .................................................................................................................. 41
13.1.1 Definition for tCK(avg) ....................................................................................................... 41
13.1.2 Definition for tCK(abs) ....................................................................................................... 41
13.1.3 Definition for tCH(avg) and tCL(avg) .................................................................................... 41
13.1.4 Definition for note for tJIT(per), tJIT(per, Ick) ........................................................................ 41
13.1.5 Definition for tJIT(cc), tJIT(cc, Ick) ...................................................................................... 41
13.1.6 Definition for tERR(nper) ................................................................................................... 41
13.2 Refresh Parameters by Device Density ....................................................................................... 42
13.3 Speed Bins and CL, tRCD, tRP, tRC and tRAS for corresponding Bin ............................................. 42
13.3.1 Speed Bin Table Notes ...................................................................................................... 45
14.0 Timing Parameters by Speed Grade ...................................................................................... 46
14.1 Jitter Notes ............................................................................................................................. 49
14.2 Timing Parameter Notes ........................................................................................................... 50
14.3 Address/Command Setup, Hold and Derating : ............................................................................ 51
14.4 Data Setup, Hold and Slew Rate Derating : ................................................................................. 57
Rev. 1.0 February 2009
Page 4 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
1.0 Ordering Information
[ Table 1 ] Samsung 1Gb DDR3 E-die ordering information table
Organization
256Mx4
DDR3-800 (6-6-6)
K4B1G0446E-HCF7
K4B1G0846E-HCF7
K4B1G1646E-HCF7
DDR3-1066 (7-7-7)
K4B1G0446E-HCF8
K4B1G0846E-HCF8
K4B1G1646E-HCF8
DDR3-1333 (9-9-9)
K4B1G0446E-HCH9
K4B1G0846E-HCH9
K4B1G1646E-HCH9
DDR3-1600 (11-11-11)
K4B1G0446E-HCK0
K4B1G0846E-HCK0
K4B1G1646E-HCK0
Package
78 FBGA
78 FBGA
96 FBGA
128Mx8
64Mx16
Note :
1. Speed bin is in order of CL-tRCD-tRP.
2.0 Key Features
[ Table 2 ] 1Gb DDR3 E-die Speed bins
DDR3-800
6-6-6
DDR3-1066
7-7-7
DDR3-1333
9-9-9
1.5
DDR3-1600
11-11-11
1.25
Speed
Unit
tCK(min)
CAS Latency
tRCD(min)
tRP(min)
2.5
6
1.875
7
ns
nCK
ns
9
11
15
13.125
13.125
37.5
13.5
13.5
36
13.75
13.75
35
15
ns
tRAS(min)
tRC(min)
37.5
52.5
ns
50.625
49.5
48.75
ns
•
•
JEDEC standard 1.5V ± 0.075V Power Supply
VDDQ = 1.5V ± 0.075V
The 1Gb DDR3 SDRAM E-die is organized as a 32Mbit x 4 I/Os x 8banks,
16Mbit x 8 I/Os x 8banks or 8Mbit x 16 I/Os x 8 banks device. This syn-
chronous device achieves high speed double-data-rate transfer rates of up
to 1600Mb/sec/pin (DDR3-1600) for general applications.
•
400 MHz fCK for 800Mb/sec/pin, 533MHz fCK for 1066Mb/sec/pin,
667MHz fCK for 1333Mb/sec/pin, 800MHz fCK for 1600Mb/sec/pin
The chip is designed to comply with the following key DDR3 SDRAM fea-
tures such as posted CAS, Programmable CWL, Internal (Self) Calibra-
tion, On Die Termination using ODT pin and Asynchronous Reset .
All of the control and address inputs are synchronized with a pair of exter-
nally supplied differential clocks. Inputs are latched at the crosspoint of dif-
ferential clocks (CK rising and CK falling). All I/Os are synchronized with a
pair of bidirectional strobes (DQS and DQS) in a source synchronous fash-
ion. The address bus is used to convey row, column, and bank address
information in a RAS/CAS multiplexing style. The DDR3 device operates
•
•
•
•
•
8 Banks
Posted CAS
Programmable CAS Latency(posted CAS): 6, 7, 8, 9, 10, 11
Programmable Additive Latency: 0, CL-2 or CL-1 clock
Programmable CAS Write Latency (CWL) = 5 (DDR3-800),
(DDR3-1066), 7 (DDR3-1333) and 8 (DDR3-1600)
6
•
•
8-bit pre-fetch
with a single 1.5V ± 0.075V power supply and 1.5V ± 0.075V VDDQ
.
Burst Length: 8 (Interleave without any limit, sequential with starting
address “000” only), 4 with tCCD = 4 which does not allow seamless
read or write [either On the fly using A12 or MRS]
The 1Gb DDR3 E-die device is available in 78ball FBGAs(x4/x8) and
96ball FBGA(x16)
•
•
Bi-directional Differential Data-Strobe
Internal(self) calibration : Internal self calibration through ZQ pin
(RZQ : 240 ohm ± 1%)
Note : 1. The functionality described and the timing specifications included
in this data sheet are for the DLL Enabled mode of operation.
•
•
On Die Termination using ODT pin
Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at
85°C < TCASE < 95 °C
•
•
Asynchronous Reset
Package : 78 balls FBGA - x4/x8
96 balls FBGA - x16
•
•
All of Lead-Free products are compliant for RoHS
All of products are Halogen-free
Note : This data sheet is an abstract of full DDR3 specification and does not cover the common features which are described in “DDR3 SDRAM Device
Operation & Timing Diagram”.
Rev. 1.0 February 2009
Page 5 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
3.0 Package pinout/Mechanical Dimension & Addressing
3.1 x4 Package Pinout (Top view) : 78ball FBGA Package
1
2
3
4
5
6
7
8
9
VSS
VSS
VDD
VSS
VDD
VDDQ
VSSQ
VSSQ
VDDQ
NC
A
B
C
D
E
F
NC
DQ0
DQS
DQS
NC
NC
DM
A
B
C
D
E
F
VSSQ
VSSQ
VDDQ
VSSQ
VREFDQ
NC
DQ2
NC
VDDQ
VSS
VDD
CS
DQ1
VDD
DQ3
VSS
NC
CK
NC
VSS
VDD
RAS
CAS
WE
BA2
A0
G
H
J
ODT
NC
VSS
CK
A10/AP
NC
CKE
NC
VSS
G
H
J
ZQ
VREFCA
BA0
A3
VDD
VSS
VDD
VSS
VDD
VSS
VDD
VSS
K
L
A12/BC
A1
BA1
A4
K
L
A5
A2
M
N
A7
A9
A11
A6
M
N
RESET
A13
NC
A8
1
2
3
4
5
6
7
8
9
Ball Locations (x4)
A
B
C
D
E
F
Populated ball
Ball not populated
G
H
J
K
L
Top view
(See the balls through the package)
M
N
Rev. 1.0 February 2009
Page 6 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
3.2 x8 Package Pinout (Top view) : 78ball FBGA Package
1
2
3
4
5
6
7
8
9
VSS
VSS
VDD
VSS
VDD
VDDQ
VSSQ
VSSQ
VDDQ
NC
A
B
C
D
E
F
NC
DQ0
DQS
DQS
DQ4
RAS
CAS
WE
NU/TDOS
DM/TDQS
DQ1
A
B
C
D
E
F
VSSQ
VSSQ
VDDQ
VSSQ
VREFDQ
NC
DQ2
DQ6
VDDQ
VSS
DQ3
VSS
VDD
DQ7
CK
DQ5
VSS
VDD
VDD
CS
BA0
A3
G
H
J
ODT
NC
VSS
CK
A10/AP
NC
CKE
NC
VSS
G
H
J
ZQ
VREFCA
BA2
A0
VDD
VSS
VDD
VSS
VDD
VSS
VDD
VSS
K
L
A12/BC
A1
BA1
A4
K
L
A5
A2
M
N
A7
A9
A11
A6
M
N
RESET
A13
NC
A8
1
2
3
4
5
6
7
8
9
Ball Locations (x8)
A
B
C
D
E
F
Populated ball
Ball not populated
G
H
J
K
L
Top view
(See the balls through the package)
M
N
Rev. 1.0 February 2009
Page 7 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
3.3 x16 Package Pinout (Top view) : 96ball FBGA Package
1
2
3
4
5
6
7
8
9
VDDQ
VSSQ
VDDQ
VSSQ
VSS
VDDQ
VSS
A
B
C
D
E
F
DQU5
VDD
DQU7
VSS
DQU4
DQSU
DQSU
DQU0
DML
A
B
C
D
E
F
VSSQ
VDDQ
VDD
DQU6
DQU2
VSSQ
VSSQ
DQU3
VDDQ
VSSQ
DQU1
DMU
DQL0
DQSL
DQSL
DQL4
RAS
CAS
WE
VDDQ
VSSQ
VSSQ
VDDQ
NC
VDDQ
VSSQ
VREFDQ
NC
DQL2
DQL6
VDDQ
VSS
DQL1
VDD
DQL3
VSS
G
H
J
G
H
J
DQL7
CK
DQL5
VSS
VDD
VDD
K
L
ODT
NC
VSS
CK
A10/AP
NC
CKE
NC
VSS
K
L
CS
BA0
A3
ZQ
VREFCA
M
N
P
R
T
BA2
A0
M
N
P
R
T
VDD
VSS
VDD
VSS
VDD
VSS
VDD
VSS
A12/BC
A1
BA1
A4
A5
A2
A7
A9
A11
A6
RESET
A13
NC
A8
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
G
H
J
Ball Locations (x16)
Populated ball
Ball not populated
K
L
Top view
(See the balls through the package)
M
N
P
R
T
Rev. 1.0 February 2009
Page 8 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
3.4 FBGA Package Dimension (x4/x8)
Units : Millimeters
7.50 ± 0.10
A
#A1 INDEX MARK
B
0.80
(Datum A)
(Datum B)
1.60
6
3.20
9
8
7
5
4
3
2 1
A
B
C
D
E
F
G
H
J
K
L
M
N
(0.95)
78 - ∅0.45 Solder ball
(Post Reflow ∅0.50 ± 0.05)
MOLDING AREA
(1.90)
0.2
M
A B
BOTTOM VIEW
7.50 ± 0.10
#A1
0.35 ± 0.05
1.10 ± 0.10
TOP VIEW
Rev. 1.0 February 2009
Page 9 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
3.5 FBGA Package Dimension (x16)
Units : Millimeters
7.50 ± 0.10
A
#A1 INDEX MARK
B
0.80
1.60
6
3.20
3
9
8
7
5
4
2 1
A
B
C
D
E
F
(Datum A)
(Datum B)
G
H
J
K
L
M
N
P
R
T
(0.95)
96 - ∅0.45 Solder ball
(Post Reflow ∅0.50 ± 0.05)
0.2 A B
MOLDING AREA
(1.90)
M
BOTTOM VIEW
7.50 ± 0.10
#A1
0.35 ± 0.05
1.10 ± 0.10
TOP VIEW
Rev. 1.0 February 2009
Page 10 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
4.0 Input/Output Functional Description
[ Table 3 ] Input/Output function description
Symbol
Type
Function
Clock: CK and CK are differential clock inputs. All address and control input signals are sampled on the crossing of
the positive edge of CK and negative edge of CK. Output (read) data is referenced to the crossings of CK and CK
CK, CK
Input
Clock Enable: CKE HIGH activates, and CKE Low deactivates, internal clock signals and device input buffers and
output drivers. Taking CKE Low provides Precharge Power-Down and Self Refresh operation (all banks idle), or
Active Power-Down (Row Active in any bank). CKE is asynchronous for self refresh exit. After VREFCA has become
stable during the power on and initialization sequence, it must be maintained during all operations (including Self-
Refresh). CKE must be maintained high throughout read and write accesses. Input buffers, excluding CK, CK, ODT
and CKE are disabled during power-down. Input buffers, excluding CKE, are disabled during Self -Refresh.
CKE
CS
Input
Chip Select: All commands are masked when CS is registered HIGH. CS provides for external Rank selection on
systems with multiple Ranks. CS is considered part of the command code.
Input
Input
On Die Termination: ODT (registered HIGH) enables termination resistance internal to the DDR3 SDRAM. When
enabled, ODT is only applied to each DQ, DQS, DQS and DM/TDQS, NU/TDQS (When TDQS is enabled via Mode
Register A11=1 in MR1) signal for x8 configurations. The ODT pin will be ignored if the Mode Register (MR1) is pro-
grammed to disable ODT.
ODT
RAS, CAS, WE
Input
Input
Command Inputs: RAS, CAS and WE (along with CS) define the command being entered.
Input Data Mask: DM is an input mask signal for write data. Input data is masked when DM is sampled HIGH coinci-
dent with that input data during a Write access. DM is sampled on both edges of DQS. For x8 device, the function of
DM or TDQS/TDQS is enabled by Mode Register A11 setting in MR1.
DM
(DMU), (DML)
Bank Address Inputs: BA0 - BA2 define to which bank an Active, Read, Write or Precharge command is being
applied. Bank address also determines if the mode register or extended mode register is to be accessed during a
MRS cycle.
BA0 - BA2
A0 - A13
Input
Input
Address Inputs: Provided the row address for Active commands and the column address for Read/Write commands
to select one location out of the memory array in the respective bank. (A10/AP and A12/BC have additional functions,
see below)
The address inputs also provide the op-code during Mode Register Set commands.
Autoprecharge: A10 is sampled during Read/Write commands to determine whether Autoprecharge should be per-
formed to the accessed bank after the Read/Write operation. (HIGH:Autoprecharge; LOW: No Autoprecharge)
A10 is sampled during a Precharge command to determine whether the Precharge applies to one bank (A10 LOW) or
all banks (A10 HIGH). if only one bank is to be precharged, the bank is selected by bank addresses.
A10 / AP
A12 / BC
Input
Burst Chop:A12 is sampled during Read and Write commands to determine if burst chop(on-the-fly) will be per-
formed. (HIGH : no burst chop, LOW : burst chopped). See command truth table for details
Input
Input
Active Low Asynchronous Reset: Reset is active when RESET is LOW, and inactive when RESET is HIGH.
RESET must be HIGH during normal operation. RESET is a CMOS rail to rail signal with DC high and low at 80% and
20% of VDD, i.e. 1.20V for DC high and 0.30V for DC low.
RESET
DQ
Input/Output Data Input/ Output: Bi-directional data bus.
Data Strobe: Output with read data, input with write data. Edge-aligned with read data, centered in write data. For the
x16, DQSL: corresponds to the data on DQL0-DQL7; DQSU corresponds to the data on DQU0-DQU7. The data
Input/Output strobe DQS, DQSL and DQSU are paired with differential signals DQS, DQSL and DQSU, respectively, to provide dif-
ferential pair signaling to the system during reads and writes. DDR3 SDRAM supports differential data strobe only and
does not support single-ended.
DQS, (DQS)
Termination Data Strobe: TDQS/TDQS is applicable for X8 DRAMs only. When enabled via Mode Register A11=1 in
MR1, DRAM will enable the same termination resistance function on TDQS/TDQS that is applied to DQS/DQS. When
TDQS, (TDQS)
Output
disabled via mode register A11=0 in MR1, DM/TDQS will provide the data mask function and TDQS is not used. x4/
x16 DRAMs must disable the TDQS function via mode register A11=0 in MR1.
NC
No Connect: No internal electrical connection is present.
VDDQ
Supply
Supply
Supply
Supply
Supply
Supply
Supply
DQ Power Supply: 1.5V +/- 0.075V
DQ Ground
VSSQ
VDD
Power Supply: 1.5V +/- 0.075V
Ground
VSS
VREFDQ
VREFCA
ZQ
Reference voltage for DQ
Reference voltage for CA
Reference Pin for ZQ calibration
Note : Input only pins (BA0-BA2, A0-A12, RAS, CAS, WE, CS, CKE, ODT and RESET) do not supply termination.
Rev. 1.0 February 2009
Page 11 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
5.0 DDR3 SDRAM Addressing
1Gb
Configuration
# of Bank
256Mb x 4
8
128Mb x 8
8
64Mb x 16
8
Bank Address
Auto precharge
Row Address
BA0 - BA2
A10/AP
A0 - A13
A0 - A9,A11
A12/BC
1 KB
BA0 - BA2
A10/AP
A0 - A13
A0 - A9
A12/BC
1 KB
BA0 - BA2
A10/AP
A0 - A12
A0 - A9
A12/BC
2 KB
Column Address
BC switch on the fly
Page size *1
2Gb
Configuration
# of Bank
512Mb x 4
8
256Mb x 8
8
128Mb x 16
8
Bank Address
Auto precharge
Row Address
BA0 - BA2
A10/AP
A0 - A14
A0 - A9,A11
A12/BC
1 KB
BA0 - BA2
A10/AP
A0 - A14
A0 - A9
A12/BC
1 KB
BA0 - BA2
A10/AP
A0 - A13
A0 - A9
A12/BC
2 KB
Column Address
BC switch on the fly
Page size *1
4Gb
Configuration
# of Bank
1Gb x 4
8
512Mb x 8
8
256Mb x 16
8
Bank Address
Auto precharge
Row Address
BA0 - BA2
A10/AP
A0 - A15
A0 - A9,A11
A12/BC
1 KB
BA0 - BA2
A10/AP
A0 - A15
A0 - A9
A12/BC
1 KB
BA0 - BA2
A10/AP
A0 - A14
A0 - A9
A12/BC
2 KB
Column Address
BC switch on the fly
Page size *1
8Gb
Configuration
# of Bank
2Gb x 4
8
1Gb x 8
8
512Mb x 16
8
Bank Address
Auto precharge
Row Address
BA0 - BA2
A10/AP
BA0 - BA2
A10/AP
A0 - A15
A0 - A9,A11
A12/BC
2 KB
BA0 - BA2
A10/AP
A0 - A15
A0 - A9
A12/BC
2 KB
A0 - A15
A0 - A9,A11,A13
A12/BC
Column Address
BC switch on the fly
Page size *1
2 KB
Note 1 : Page size is the number of bytes of data delivered from the array to the internal sense amplifiers when an ACTIVE command is registered.
Page size is per bank, calculated as follows:
page size = 2 COLBITS * ORG÷8
where, COLBITS = the number of column address bits, ORG = the number of I/O (DQ) bits
Rev. 1.0 February 2009
Page 12 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
6.0 Absolute Maximum Ratings
6.1 Absolute Maximum DC Ratings
[ Table 4 ] Absolute Maximum DC Ratings
Symbol
Parameter
Rating
Units
Notes
VDD
Voltage on VDD pin relative to Vss
-0.4 V ~ 1.975 V
V
1,3
VDDQ
Voltage on VDDQ pin relative to Vss
Voltage on any pin relative to Vss
Storage Temperature
-0.4 V ~ 1.975 V
-0.4 V ~ 1.975 V
-55 to +100
V
V
1,3
1
V
IN, VOUT
TSTG
Note :
°C
1, 2
1. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect reliability.
2. Storage Temperature is the case surface temperature on the center/top side of the DRAM. For the measurement conditions, please refer to JESD51-2
standard.
3. VDD and VDDQ must be within 300mV of each other at all times;and VREF must be not greater than 0.6 x VDDQ, When VDD and VDDQ are less than
500mV; VREF may be equal to or less than 300mV.
6.2 DRAM Component Operating Temperature Range
[ Table 5 ] Temperature Range
Symbol
Parameter
rating
Unit
Notes
TOPER
Operating Temperature Range
0 to 95
°C
1, 2, 3
Note :
1. Operating Temperature TOPER is the case surface temperature on the center/top side of the DRAM. For measurement conditions, please refer to the
JEDEC document JESD51-2.
2. The Normal Temperature Range specifies the temperatures where all DRAM specifications will be supported. During operation, the DRAM case tem-
perature must be maintained between 0-85°C under all operating conditions
3. Some applications require operation of the Extended Temperature Range between 85°C and 95°C case temperature. Full specifications are guaran-
teed in this range, but the following additional conditions apply:
a) Refresh commands must be doubled in frequency, therefore reducing the refresh interval tREFI to 3.9us. It is also possible to specify a component
with 1X refresh (tREFI to 7.8us) in the Extended Temperature Range.
b) If Self-Refresh operation is required in the Extended Temperature Range, then it is mandatory to either use the Manual Self-Refresh mode with
Extended Temperature Range capability (MR2 A6 = 0b and MR2 A7 = 1b) or enable the optional Auto Self-Refresh mode (MR2 A6 = 1b and MR2 A7 =
0b)
7.0 AC & DC Operating Conditions
7.1 Recommended DC operating Conditions (SSTL_1.5)
[ Table 6 ] Recommended DC Operating Conditions
Rating
Symbol
Parameter
Units
Notes
Min.
1.425
1.425
Typ.
1.5
Max.
1.575
1.575
VDD
Supply Voltage
Supply Voltage for Output
V
V
1,2
1,2
VDDQ
1.5
Note :
1. Under all conditions VDDQ must be less than or equal to VDD
2. VDDQ tracks with VDD. AC parameters are measured with VDD and VDDQ tied together.
.
Rev. 1.0 February 2009
Page 13 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
8.0 AC & DC Input Measurement Levels
8.1 AC & DC Logic input levels for single-ended signals
[ Table 7 ] Single-ended AC & DC input levels for Command and Address
DDR3-800/1066
DDR3-1333/1600
Min.
Symbol
Parameter
Unit Notes
Min.
Max.
Max.
VIH.CA(DC)
VREF + 100
VDD
VREF + 100
VDD
DC input logic high
DC input logic low
AC input logic high
AC input logic low
AC input logic high
AC input logic lowM
mV
mV
mV
mV
mV
mV
1
V
IL.CA(DC)
IH.CA(AC)
IL.CA(AC)
IH.CA(AC150)
IL.CA(AC150)
VSS
VREF - 100
VSS
VREF - 100
1
V
VREF + 175
VREF + 175
-
-
1,2
1,2
1,2
1,2
V
VREF - 175
VREF - 175
-
-
-
-
V
VREF+150
-
-
-
V
VREF-150
-
Reference Voltage for ADD,
CMD inputs
V
REFCA(DC)
0.49*VDD
0.51*VDD
0.49*VDD
0.51*VDD
V
3,4
Note :
1. For input only pins except RESET, VREF = VREFCA(DC)
2. See 9.6 "Overshoot and Undershoot specifications"
3. The AC peak noise on VREF may not allow VREF to deviate from VREF(DC) by more than ± 1% VDD (for reference : approx. ± 15mV)
4. For reference : approx. VDD/2 ± 15mV
[ Table 8 ] Single-ended AC & DC input levels for DQ and DM
DDR3-800/1066
DDR3-1333/1600
Min.
Symbol
Parameter
Unit Notes
Min.
Max.
Max.
VIH.DQ(DC)
VREF + 100
VSS
VDD
VREF + 100
VSS
VDD
DC input logic high
DC input logic low
mV
mV
mV
mV
V
1
V
IL.DQ(DC)
IH.DQ(AC)
IL.DQ(AC)
VREFDQ(DC)
Note :
VREF - 100
VREF - 100
1
V
VREF + 175
VREF + 150
AC input logic high
AC input logic low
-
-
1,2,5
1,2,5
3,4
V
VREF - 175
0.51*VDD
VREF - 150
0.51*VDD
-
-
0.49*VDD
0.49*VDD
I/O Reference Voltage(DQ)
1. For input only pins except RESET, VREF = VREFDQ(DC)
2. See "Overshoot and Undershoot specifications"
3. The AC peak noise on VREF may not allow VREF to deviate from VREF(DC) by more than ± 1% VDD (for reference : approx. ± 15mV)
4. For reference : approx. VDD/2 ± 15mV
5. Single ended swing requirement for DQS - DQS is 350mV (peak to peak). Differential swing for DQS - DQS is 700mV (peak to peak).
Rev. 1.0 February 2009
Page 14 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
8.2 V
Tolerances
REF
The dc-tolerance limits and ac-noise limits for the reference voltages VREFCA and VREFDQ are illustrate in Figure 1. It shows a valid reference voltage
REF(t) as a function of time. (VREF stands for VREFCA and VREFDQ likewise).
REF(DC) is the linear average of VREF(t) over a very long period of time (e.g. 1 sec). This average has to meet the min/max requirements in table 7.
V
V
Furthermore VREF(t) may temporarily deviate from VREF(DC) by no more than ± 1% VDD
.
voltage
VDD
VSS
time
Figure 1. Illustration of VREF(DC) tolerance and VREF ac-noise limits
The voltage levels for setup and hold time measurements VIH(AC), VIH(DC), VIL(AC) and VIL(DC) are dependent on VREF
.
"VREF" shall be understood as VREF(DC), as defined in Figure 1.
This clarifies, that dc-variations of VREF affect the absolute voltage a signal has to reach to achieve a valid high or low level and therefore the time to
which setup and hold is measured. System timing and voltage budgets need to account for VREF(DC) deviations from the optimum position within the
data-eye of the input signals.
This also clarifies that the DRAM setup/hold specification and derating values need to include time and voltage associated with VREF ac-noise. Timing
and voltage effects due to ac-noise on VREF up to the specified limit (+/-1% of VDD) are included in DRAM timings and their associated deratings.
Rev. 1.0 February 2009
Page 15 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
8.3 AC & DC Logic Input Levels for Differential Signals
8.3.1 Differential signals definition
tDVAC
VIH.DIFF.AC.MIN
VIH.DIFF.MIN
0.0
half cycle
VIL.DIFF.MAX
VIL.DIFF.AC.MAX
tDVAC
time
Figure 2 : Definition of differential ac-swing and "time above ac level" tDVAC
8.3.2 Differential swing requirement for clock (CK - CK) and strobe (DQS - DQS)
[ Table 9 ] Differential AC & DC Input Levels
DDR3-800/1066/1333/1600
Symbol
Parameter
unit
Note
min
+0.2
max
VIHdiff
VILdiff
differential input high
differential input low
note 3
-0.2
V
V
V
V
1
1
2
2
note 3
VIHdiff(AC)
2 x (VIH(AC)-VREF)
differential input high ac
differential input low ac
note 3
V
ILdiff(AC)
2 x (VREF - VIL(AC))
note 3
Notes:
1. Used to define a differential signal slew-rate.
2. for CK - CK use VIH/VIL(AC) of ADD/CMD and VREFCA; for DQS - DQS, DQSL - DQSL, DQSU - DQSU use VIH/VIL(AC) of DQs and VREFDQ; if a
reduced ac-high or ac-low level is used for a signal group, then the reduced level applies also here.
3. These values are not defined, however they single-ended signals CK, CK, DQS, DQS, DQSL, DQSL, DQSU, DQSU need to be within the respective
limits (VIH(DC) max, VIL(DC)min) for single-ended signals as well as the limitations for overshoot and undershoot. Refer to "overshoot and Undershoot
Specification "
[ Table 10 ] Allowed time before ringback (tDVAC) for CLK - CLK and DQS - DQS
tDVAC [ps] @ |VIH/Ldiff(AC)| = 350mV
tDVAC [ps] @ |VIH/Ldiff(AC)| = 300mV
Slew Rate [V/ns]
min
75
57
50
38
34
29
22
13
0
max
min
175
170
167
163
162
161
159
155
150
150
max
> 4.0
4.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3.0
2.0
1.8
1.6
1.4
1.2
1.0
< 1.0
0
Rev. 1.0 February 2009
Page 16 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
8.3.3 Single-ended requirements for differential signals
Each individual component of a differential signal (CK, DQS, DQSL, DQSU, CK, DQS, DQSL, or DQSU) has also to comply with certain requirements for
single-ended signals.
CK and CK have to approximately reach VSEHmin / VSELmax [approximately equal to the ac-levels { VIH(AC) / VIL(AC)} for ADD/CMD signals] in every
half-cycle.
DQS, DQSL, DQSU, DQS, DQSL have to reach VSEHmin / VSELmax [approximately the ac-levels { VIH(AC) / VIL(AC)} for DQ signals] in every half-cycle
proceeding and following a valid transition.
Note that the applicable ac-levels for ADD/CMD and DQ’s might be different per speed-bin etc. E.g. if VIH150(AC)/VIL150(AC) is used for ADD/CMD sig-
nals, then these ac-levels apply also for the single-ended signals CK and CK .
VDD or VDDQ
VSEH min
VSEH
VDD/2 or VDDQ/2
CK or DQS
VSEL max
VSEL
VSS or VSSQ
time
Figure 3 : Single-ended requirement for differential signals.
Note that while ADD/CMD and DQ signal requirements are with respect to VREF, the single-ended components of differential signals have a requirement
with respect to VDD/2; this is nominally the same. The transition of single-ended signals through the ac-levels is used to measure setup time. For single-
ended components of differential signals the requirement to reach VSELmax, VSEHmin has no bearing on timing, but adds a restriction on the common
mode characteristics of these signals.
[ Table 11 ] Single-ended levels for CK, DQS, DQSL, DQSU, CK, DQS, DQSL, or DQSU
DDR3-800/1066/1333/1600
Symbol
Parameter
Unit
Notes
Min
Max
Note3
Note3
(VDD/2)+0.175
(VDD/2)+0.175
Note3
Single-ended high-level for strobes
Single-ended high-level for CK, CK
Single-ended low-level for strobes
Single-ended low-level for CK, CK
V
V
V
V
1, 2
1, 2
1, 2
1, 2
VSEH
(VDD/2)-0.175
(VDD/2)-0.175
VSEL
Note3
Notes:
1. For CK, CK use VIH/VIL(AC) of ADD/CMD; for strobes (DQS, DQS, DQSL, DQSL, DQSU, DQSU) use VIH/VIL(AC) of DQs.
2. VIH(AC)/VIL(AC) for DQs is based on VREFDQ; VIH(AC)/VIL(AC) for ADD/CMD is based on VREFCA; if a reduced ac-high or ac-low level is used for a
signal group, then the reduced level applies also here
3. These values are not defined, however they single-ended signals CK, CK, DQS, DQS, DQSL, DQSL, DQSU, DQSU need to be within the respective
limits (VIH(DC) max, VIL(DC)min) for single-ended signals as well as the limitations for overshoot and undershoot. Refer to "Overshoot and Undershoot
Specification"
Rev. 1.0 February 2009
Page 17 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
8.4 Differential Input Cross Point Voltage
To guarantee tight setup and hold times as well as output skew parameters with respect to clock and strobe, each cross point voltage of differential input
signals (CK, CK and DQS, DQS) must meet the requirements in below table. The differential input cross point voltage VIX is measured from the actual
cross point of true and complement signal to the mid level between of VDD and VSS
.
VDD
CK, DQS
VIX
VDD/2
VIX
VIX
CK, DQS
VSS
Figure 4. VIX Definition
[ Table 12 ] Cross point voltage for differential input signals (CK, DQS)
DDR3-800/1066/1333/1600
Symbol
Parameter
Unit
Notes
Min
-150
-175
-150
Max
150
175
150
mV
mV
mV
VIX
VIX
Differential Input Cross Point Voltage relative to VDD/2 for CK,CK
Differential Input Cross Point Voltage relative to VDD/2 for DQS,DQS
1
Note :
1. Extended range for VIX is only allowed for clock and if single-ended clock input signals CKand CK are monotonic, have a single-ended swing VSEL
SEH of at least VDD/2 =/-250 mV, and the differential slew rate of CK-CK is larger than 3 V/ ns. Refer to table 11 on page 17 for VSEL and VSEH stan-
/
V
dard values.
8.5 Slew rate definition for Differential Input Signals
See 14.3 "Address / Command Setup, Hold and Derating" for single-ended slew rate definitions for address and command signals.
See 14.4 "Data Setup, Hold and Slew Rate Derating" for single-ended slew rate definitions for data signals.tDH nominal slew rate for a falling signal is
defined as the slew rate between the last crossing of VIH(DC)min and the first crossing of VREF
8.6 Slew rate definition for Differential Input Signals
Input slew rate for differential signals (CK, CK and DQS, DQS) are defined and measured as shown in Table 13 and Figure 5.
[ Table 13 ] Differential input slew rate definition
Measured
Description
Defined by
From
To
VIHdiffmin - VILdiffmax
Delta TRdiff
VIHdiffmin - VILdiffmax
VILdiffmax
VIHdiffmin
Differential input slew rate for rising edge (CK-CK and DQS-DQS)
Differential input slew rate for falling edge (CK-CK and DQS-DQS)
VIHdiffmin
VILdiffmax
Delta TFdiff
V
IHdiffmin
0
V
ILdiffmax
delta TFdiff
delta TRdiff
Figure 5. Differential Input Slew Rate definition for DQS, DQS and CK, CK
Rev. 1.0 February 2009
Page 18 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
9.0 AC & DC Output Measurement Levels
9.1 Single-ended AC & DC Output Levels
[ Table 14 ] Single-ended AC & DC output levels
Symbol
Parameter
DDR3-800/1066/1333/1600
Units
Notes
VOH(DC)
DC output high measurement level (for IV curve linearity)
0.8 x VDDQ
V
V
OM(DC)
OL(DC)
OH(AC)
OL(AC)
DC output mid measurement level (for IV curve linearity)
DC output low measurement level (for IV curve linearity)
AC output high measurement level (for output SR)
AC output low measurement level (for output SR)
0.5 x VDDQ
0.2 x VDDQ
V
V
V
V
V
V
VTT + 0.1 x VDDQ
VTT - 0.1 x VDDQ
1
1
V
Note : 1. The swing of +/-0.1 x VDDQ is based on approximately 50% of the static single ended output high or low swing with a driver impedance of 40Ω
and an effective test load of 25Ω to VTT=VDDQ/2.
9.2 Differential AC & DC Output Levels
[ Table 15 ] Differential AC & DC output levels
Symbol
Parameter
DDR3-800/1066/1333/1600
Units
Notes
V
OHdiff(AC)
AC differential output high measurement level (for output SR)
+0.2 x VDDQ
V
1
V
OLdiff(DC)
AC differential output low measurement level (for output SR)
-0.2 x VDDQ
V
1
Note : 1. The swing of +/-0.2xVDDQ is based on approximately 50% of the static single ended output high or low swing with a driver impedance of 40Ω
and an effective test load of 25Ω to VTT=VDDQ/2 at each of the differential outputs.
9.3 Single-ended Output Slew Rate
With the reference load for timing measurements, output slew rate for falling and rising edges is defined and measured between VOL(AC) and VOH(AC)
for single ended signals as shown in Table 16 and figure 6.
[ Table 16 ] Single-ended output slew rate definition
Measured
Description
Defined by
From
To
VOH(AC)-VOL(AC)
Delta TRse
V
OL(AC)
VOH(AC)
Single ended output slew rate for rising edge
Single ended output slew rate for falling edge
VOH(AC)-VOL(AC)
Delta TFse
V
OH(AC)
VOL(AC)
Note : Output slew rate is verified by design and characterization, and may not be subject to production test.
[ Table 17 ] Single-ended output slew rate
DDR3-800
DDR3-1066
DDR3-1333
DDR3-1600
Parameter
Symbol
Units
Min
2.5
Max
5
Min
2.5
Max
5
Min
2.5
Max
5
Min
Max
Single ended output slew rate
Description : SR : Slew Rate
SRQse
TBD
5
V/ns
Q : Query Output (like in DQ, which stands for Data-in, Query-Output
se : Singe-ended Signals
For Ron = RZQ/7 setting
V
OH(AC)
V
V
TT
OL(AC)
delta TFse
delta TRse
Figure 6. Single-ended Output Slew Rate Definition
Rev. 1.0 February 2009
Page 19 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
9.4 Differential Output Slew Rate
With the reference load for timing measurements, output slew rate for falling and rising edges is defined and measured between VOLdiff(AC) and
V
OHdiff(AC) for differential signals as shown in Table 18 and figure 7.
[ Table 18 ] Differential output slew rate definition
Description
Measured
Defined by
From
To
VOHdiff(AC)-VOLdiff(AC)
Delta TRdiff
V
OLdiff(AC)
VOHdiff(AC)
VOLdiff(AC)
Differential output slew rate for rising edge
Differential output slew rate for falling edge
VOHdiff(AC)-VOLdiff(AC)
Delta TFdiff
V
OHdiff(AC)
Note : Output slew rate is verified by design and characterization, and may not be subject to production test.
[ Table 19 ] Differential output slew rate
DDR3-800
DDR3-1066
DDR3-1333
DDR3-1600
Parameter
Symbol
Units
Min
Max
Min
Max
Min
Max
Min
TBD
Max
10
Differential output slew rate
Description : SR : Slew Rate
SRQse
5
10
5
10
5
10
V/ns
Q : Query Output (like in DQ, which stands for Data-in, Query-Output
diff : Singe-ended Signals
For Ron = RZQ/7 setting
V
(AC)
(AC)
OHdiff
V
V
TT
OLdiff
delta TFdiff
delta TRdiff
Figure 7. Differential Output Slew Rate Definition
9.5 Reference Load for AC Timing and Output Slew Rate
Figure 8 represents the effective reference load of 25 ohms used in defining the relevant AC timing parameters of the device as well as output slew rate
measurements.
It is not intended as a precise representation of any particular system environment of a depiction of the actual load presented by a production tester. Sys-
tem designers should use IBIS or other simulation tools to correlate the timing reference load to a system environment. Manufacturers correlate to their
production test conditions, generally one or more coaxial transmission lines terminated at the tester electronics.
VDDQ
DQ
CK/CK
DQS
DUT
VTT = VDDQ/2
DQS
25Ω
Reference
Point
Figure 8. Reference Load for AC Timing and Output Slew Rate
Rev. 1.0 February 2009
Page 20 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
9.6 Overshoot/Undershoot Specification
9.6.1 Address and Control Overshoot and Undershoot specifications
[ Table 20 ] AC overshoot/undershoot specification for Address and Control pins (A0-A12, BA0-BA2. CS. RAS. CAS. WE. CKE, ODT)
Specification
Parameter
Unit
DDR3-800
0.4V
DDR3-1066
0.4V
DDR3-1333
0.4V
DDR3-1600
0.4V
Maximum peak amplitude allowed for overshoot area (See Figure 9)
Maximum peak amplitude allowed for undershoot area (See Figure 9)
Maximum overshoot area above VDD (See Figure 9)
V
V
0.4V
0.4V
0.4V
0.4V
0.67V-ns
0.5V-ns
0.4V-ns
0.33V-ns
V-ns
Maximum undershoot area below VSS (See Figure 9)
0.67V-ns
0.5V-ns
0.4V-ns
0.33V-ns
V-ns
Maximum Amplitude
Overshoot Area
VDD
VSS
Volts
(V)
Undershoot Area
Maximum Amplitude
Time (ns)
Figure 9. Address and Control Overshoot and Undershoot Definition
9.6.2 Clock, Data, Strobe and Mask Overshoot and Undershoot Specifications
[ Table 21 ] AC overshoot/undershoot specification for Clock, Data, Strobe and Mask (DQ, DQS, DQS, DM, CK, CK)
Specification
Parameter
Unit
DDR3-800
0.4V
DDR3-1066
0.4V
DDR3-1333
0.4V
DDR3-1600
0.4V
Maximum peak amplitude allowed for overshoot area (See Figure 11)
Maximum peak amplitude allowed for undershoot area (See Figure 11)
Maximum overshoot area above VDDQ (See Figure 11)
V
V
0.4V
0.4V
0.4V
0.4V
0.25V-ns
0.19V-ns
0.15V-ns
0.13V-ns
V-ns
Maximum undershoot area below VSSQ (See Figure 11)
0.25V-ns
0.19V-ns
0.15V-ns
0.13V-ns
V-ns
Maximum Amplitude
Overshoot Area
Undershoot Area
VDDQ
VSSQ
Volts
(V)
Maximum Amplitude
Time (ns)
Figure 10. Clock, Data, Strobe and Mask Overshoot and Undershoot Definition
Rev. 1.0 February 2009
Page 21 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
9.7 34ohm Output Driver DC Electrical Characteristics
A functional representation of the output buffer is shown below. Output driver impedance RON is defined by the value of external reference resistor RZQ
as follows:
RON34 = RZQ/7 (Nominal 34ohms +/- 10% with nominal RZQ=240ohm)
RON40 = RZQ/6 (Nominal 40ohms +/- 10% with nominal RZQ=240ohm)
The individual Pull-up and Pull-down resistors (RONpu and RONpd) are defined as follows
VDDQ-VOUT
under the condition that RONpd is turned off
RONpu =
l Iout l
VOUT
l Iout l
under the condition that RONpu is turned off
Output Driver : Definition of Voltages and Currents
Output Driver
RONpd =
VDDQ
Ipu
To
RON
other
circuity
Pu
DQ
Iout
RON
Pd
Vout
VSSQ
Ipd
Figure 11. Output Driver : Definition of Voltages and Currents
[ Table 22 ] Output Driver DC Electrical Characteristics, assuming RZQ=240ohms ;
entire operating temperature range ; after proper ZQ calibration
RONnom
Resistor
Vout
OLdc = 0.2 x VDDQ
Min
0.6
0.9
0.9
0.9
0.9
0.6
0.6
0.9
0.9
0.9
0.9
0.6
Nom
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
Max
1.1
1.1
1.4
1.4
1.1
1.1
1.1
1.1
1.4
1.4
1.1
1.1
Units
Notes
1,2,3
1,2,3
1,2,3
1,2,3
1,2,3
1,2,3
1,2,3
1,2,3
1,2,3
1,2,3
1,2,3
1,2,3
V
V
OMdc = 0.5 x VDDQ
RON34pd
VOHdc = 0.8 x VDDQ
VOLdc = 0.2 x VDDQ
34Ohms
RZQ/7
V
OMdc = 0.5 x VDDQ
OHdc = 0.8 x VDDQ
OLdc = 0.2 x VDDQ
OMdc = 0.5 x VDDQ
OHdc = 0.8 x VDDQ
OLdc = 0.2 x VDDQ
OMdc = 0.5 x VDDQ
OHdc = 0.8 x VDDQ
RON34pu
RON40pd
RON40pu
V
V
V
V
40Ohms
RZQ/6
%
V
V
V
Mismatch between Pull-up and Pull-down,
MMpupd
V
OMdc = 0.5 x VDDQ
-10
10
1,2,4
Note :
1. The tolerance limits are specified after calibration with stable voltage and temperature. For the behavior of the tolerance limits if temperature or voltage changes after calibra-
tion, see following section on voltage and temperature sensitivity
2. The tolerance limits are specified under the condition that V
= V and that V
= V
SSQ SS
DDQ
DD
3. Pull-down and pull-up output driver impedance are recommended to be calibrated at 0.5 X V
. Other calibration schemes may be used to achieve the linearity spec
DDQ
shown above, e.g. calibration at 0.2 X V
and 0.8 X V
DDQ
DDQ
4. Measurement definition for mismatch between pull-up and pull-down, MMpupd: Measure RONpu and RONpd. both at 0.5 X V
:
DDQ
RONpu - RONpd
x 100
MMpupd
=
RONnom
Rev. 1.0 February 2009
Page 22 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
9.7.1 Output Drive Temperature and Voltage Sensitivity
If temperature and/or voltage change after calibration, the tolerance limits widen according to table 23 and 24.
∆T = T - T(@calibration); ∆V = VDDQ - VDDQ (@calibration); VDD = VDDQ
*dRONdT and dRONdV are not subject to production test but are verified by design and characterization
[ Table 23 ] Output Driver Sensitivity Definition
Min
Max
Units
RONPU@VOHDC
RON@VOMDC
0.6 - dRONdTH * |∆T| - dR dVH * |∆V|
1.1 + dRONdTH * |∆T| + dR dVH * |∆V|
RZQ/7
RZQ/7
RZQ/7
ON
ON
0.9 - dRONdTM * |∆T| - dR dVM * |∆V|
1.1 + dRONdTM * |∆T| + dR dVM * |∆V|
ON
ON
RONPD@VOLDC
0.6 - dRONdTL * |∆T| - dR dVL * |∆V|
1.1 + dRONdTL * |∆T| + dR dVL * |∆V|
ON
ON
[ Table 24 ] Output Driver Voltage and Temperature Sensitivity
Speed Bin
800/1066/1333
1600
Units
Min
0
Max
1.5
Min
0
Max
1.5
dRONdTM
dRONdVM
dRONdTL
dRONdVL
dRONdTH
dRONdVH
%/°C
%/mV
%/°C
0
0.15
1.5
0
0.13
1.5
0
0
0
0.15
1.5
0
0.13
1.5
%/mV
%/°C
0
0
0
0.15
0
0.13
%/mV
9.8 On-Die Termination (ODT) Levels and I-V Characteristics
On-Die Termination effective resistance RTT is defined by bits A9, A6 and A2 of MR1 register.
ODT is applied to the DQ,DM, DQS/DQS and TDQS,TDQS (x8 devices only) pins.
A functional representation of the on-die termination is shown below. The individual pull-up and pull-down resistors (RTTpu and RTTpd) are defined as
follows :
V
DDQ-VOUT
under the condition that RTTpd is turned off
under the condition that RTTpu is turned off
RTTpu =
RTTpd =
l Iout l
VOUT
l Iout l
On-Die Termination : Definition of Voltages and Currents
Chip in Termination Mode
ODT
VDDQ
Ipu
Iout=Ipd-Ipu
To
RTTPu
other
circuitry
DQ
like
RCV,
...
Iout
RTTPd
Ipd
VOUT
VSSQ
Figure 12. On-Die Termination : Definition of Voltages and Currents
Rev. 1.0 February 2009
Page 23 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
9.8.1 ODT DC Electrical Characteristics
Table 26 provides and overview of the ODT DC electrical characteristics. They values for RTT60pd120, RTT60pu120, RTT120pd240, RTT120pu240, RTT40pd80,
RTT40pu80, RTT30pd60, RTT30pu60, RTT20pd40, RTT20pu40 are not specification requirements, but can be used as design guide lines:
[ Table 25 ] ODT DC Electrical Characteristics, assuming RZQ=240ohm +/- 1% entire operating temperature range; after proper ZQ calibration
MR1 (A9,A6,A2)
RTT
RESISTOR
Vout
Min
Nom
Max
Unit
RZQ
Notes
VOL(DC) 0.2XVDDQ
0.5XVDDQ
0.6
0.9
0.9
0.9
0.9
0.6
0.9
0.6
0.9
0.9
0.9
0.9
0.6
0.9
0.6
0.9
0.9
0.9
0.9
0.6
0.9
0.6
0.9
0.9
0.9
0.9
0.6
0.9
0.6
0.9
0.9
0.9
0.9
0.6
0.9
-5
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.1
1.1
1.4
1.4
1.1
1.1
1.6
1.1
1.1
1.4
1.4
1.1
1.1
1.6
1.1
1.1
1.4
1.4
1.1
1.1
1.6
1.1
1.1
1.4
1.4
1.1
1.1
1.6
1.1
1.1
1.4
1.4
1.1
1.1
1.6
5
1,2,3,4
1,2,3,4
1,2,3,4
1,2,3,4
1,2,3,4
1,2,3,4
1,2,5
RTT120pd240
RZQ
V
OH(DC) 0.8XVDDQ
RZQ
VOL(DC) 0.2XVDDQ
0.5XVDDQ
RZQ
(0,1,0)
120 ohm
RTT120pu240
RZQ
VOH(DC) 0.8XVDDQ
VIL(AC) to VIH(AC)
VOL(DC) 0.2XVDDQ
0.5XVDDQ
RZQ
RTT120
RZQ/2
RZQ/2
RZQ/2
1,2,3,4
1,2,3,4
1,2,3,4
1,2,3,4
1,2,3,4
1,2,3,4
1,2,5
RTT60pd240
V
OH(DC) 0.8XVDDQ
RZQ/2
VOL(DC) 0.2XVDDQ
0.5XVDDQ
RZQ/2
RZQ/2
RZQ/2
RZQ/4
RZQ/3
RZQ/3
RZQ/3
RZQ/3
RZQ/3
RZQ/3
RZQ/6
RZQ/4
RZQ/4
RZQ/4
RZQ/4
RZQ/4
RZQ/4
RZQ/8
RZQ/6
RZQ/6
RZQ/6
RZQ/6
RZQ/6
RZQ/6
RZQ/12
(0,0,1)
(0,1,1)
(1,0,1)
(1,0,0)
60 ohm
40 ohm
30 ohm
20 ohm
RTT60pu240
RTT60
V
OH(DC) 0.8XVDDQ
VIL(AC) to VIH(AC)
VOL(DC) 0.2XVDDQ
0.5XVDDQ
1,2,3,4
1,2,3,4
1,2,3,4
1,2,3,4
1,2,3,4
1,2,3,4
1,2,5
RTT40pd240
V
OH(DC) 0.8XVDDQ
VOL(DC) 0.2XVDDQ
0.5XVDDQ
RTT40pu240
RTT40
V
OH(DC) 0.8XVDDQ
VIL(AC) to VIH(AC)
VOL(DC) 0.2XVDDQ
0.5XVDDQ
1,2,3,4
1,2,3,4
1,2,3,4
1,2,3,4
1,2,3,4
1,2,3,4
1,2,5
RTT60pd240
V
OH(DC) 0.8XVDDQ
VOL(DC) 0.2XVDDQ
0.5XVDDQ
RTT60pu240
RTT60
V
OH(DC) 0.8XVDDQ
VIL(AC) to VIH(AC)
VOL(DC) 0.2XVDDQ
0.5XVDDQ
1,2,3,4
1,2,3,4
1,2,3,4
1,2,3,4
1,2,3,4
1,2,3,4
1,2,5
RTT60pd240
V
OH(DC) 0.8XVDDQ
VOL(DC) 0.2XVDDQ
0.5XVDDQ
RTT60pu240
RTT60
V
OH(DC) 0.8XVDDQ
VIL(AC) to VIH(AC)
Deviation of VM w.r.t VDDQ/2, ∆VM
%
1,2,5,6
Rev. 1.0 February 2009
Page 24 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
Note :
1. The tolerance limits are specified after calibration with stable voltage and temperature. For the behavior of the tolerance limits if temperature or voltage
changes after calibration, see following section on voltage and temperature sensitivity
2. The tolerance limits are specified under the condition that VDDQ = VDD and that VSSQ = VSS
3. Pull-down and pull-up ODT resistors are recommended to be calibrated at 0.5XVDDQ. Other calibration schemes may be used to achieve the linearity
spec shown above, e.g. calibration at 0.2XVDDQ and 0.8XVDDQ
.
4. Not a specification requirement, but a design guide line
5. Measurement definition for RTT:
Apply VIH(AC) to pin under test and measure current I(VIH(AC)), then apply VIL(AC) to pin under test and measure current I(VIL(AC)) perspectively
VIH(AC) - VIL(AC)
RTT
=
I(VIH(AC)) - I(VIL(AC))
6. Measurement definition for VM and ∆VM : Measure voltage (VM) at test pin (midpoint) with no load
2 x VM
- 1
x 100
∆ VM
=
VDDQ
9.8.2 ODT Temperature and Voltage sensitivity
If temperature and/or voltage change after calibration, the tolerance limits widen according to table below
∆T = T - T(@calibration); ∆V = VDDQ - VDDQ (@calibration); VDD = VDDQ
[ Table 26 ] ODT Sensitivity Definition
Min
Max
Units
0.9 - dRTTdT * |∆T| - dR dV * |∆V|
1.6 + dRTTdT * |∆T| + dR dV * |∆V|
RTT
RZQ/2,4,6,8,12
TT
TT
[ Table 27 ] ODT Voltage and Temperature Sensitivity
Min
Max
1.5
Units
%/°C
dRTTdT
0
0
dRTTdV
0.15
%/mV
These parameters may not be subject to production test. They are verified by design and characterization.
Rev. 1.0 February 2009
Page 25 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
9.9 ODT Timing Definitions
9.9.1 Test Load for ODT Timings
Different than for timing measurements, the reference load for ODT timings is defined in Figure 13.
VDDQ
DUT
DQ, DM
CK,CK
VTT
=
DQS , DQS
VSSQ
RTT
=25 ohm
TDQS , TDQS
VSSQ
Timing Reference Points
Figure 13. ODT Timing Reference Load
9.9.2 ODT Timing Definitions
Definitions for tAON, tAONPD, tAOF, tAOFPD and tADC are provided in Table 28 and subsequent figures. Measurement reference settings are provided
in Table 29.
[ Table 28 ] ODT Timing Definitions
Symbol
tAON
Begin Point Definition
End Point Definition
Extrapolated point at VSSQ
Figure
Rising edge of CK - CK defined by the end point of ODTLon
Rising edge of CK - CK with ODT being first registered high
Rising edge of CK - CK defined by the end point of ODTLoff
Rising edge of CK - CK with ODT being first registered low
Figure 14
Figure 15
Figure 16
Figure 17
tAONPD
tAOF
Extrapolated point at VSSQ
End point: Extrapolated point at VRTT_Nom
End point: Extrapolated point at VRTT_Nom
tAOFPD
Rising edge of CK - CK defined by the end point of ODTLcnw,
ODTLcwn4 of ODTLcwn8
End point: Extrapolated point at VRTT_Wr and VRTT_Nom
respectively
tADC
Figure 18
[ Table 29 ] Reference Settings for ODT Timing Measurements
Measured
RTT_Nom Setting
RTT_Wr Setting
VSW1[V]
VSW2[V]
Note
Parameter
RZQ/4
RZQ/12
RZQ/4
NA
NA
0.05
0.10
0.05
0.10
0.05
0.10
0.05
0.10
0.20
0.10
0.20
0.10
0.20
0.10
0.20
0.10
0.20
0.30
tAON
NA
tAONPD
tAOF
RZQ/12
RZQ/4
NA
NA
RZQ/12
RZQ/4
NA
NA
tAOFPD
tADC
RZQ/12
RZQ/12
NA
RZQ/2
Rev. 1.0 February 2009
Page 26 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
Begin point : Rising edge of CK - CK
defined by the end point of ODTLon
CK
CK
V
TT
t
AON
T
SW2
T
SW1
DQ, DM
DQS , DQS
TDQS , TDQS
V
SW2
V
SW1
VSSQ
VSSQ
End point Extrapolated point at VSSQ
Figure 14. Definition of tAON
Begin point : Rising edge of CK - CK
with ODT being first registered high
CK
CK
V
TT
t
AONPD
T
SW2
T
SW1
DQ, DM
DQS , DQS
TDQS , TDQS
V
SW2
V
SW1
VSSQ
VSSQ
End point Extrapolated point at VSSQ
Figure 15. Definition of tAONPD
Begin point : Rising edge of CK - CK
defined by the end point of ODTLoff
CK
CK
V
TT
t
AOF
End point Extrapolated point at VRTT_Nom
VRTT_Nom
T
SW2
T
DQ, DM
SW1
DQS , DQS
V
SW2
V
TDQS , TDQS
SW1
VSSQ
TD_TAON_DEF
Figure 16. Definition of tAOF
Rev. 1.0 February 2009
Page 27 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
Begin point : Rising edge of CK - CK
with ODT being first registered low
CK
CK
V
TT
t
AOFPD
End point Extrapolated point at VRTT_Nom
VRTT_Nom
T
SW2
T
DQ, DM
SW1
DQS , DQS
V
SW2
V
TDQS , TDQS
SW1
VSSQ
Figure 17. Definition of tAOFPD
Begin point : Rising edge of CK - CK
defined by the end point of ODTLcnw
Begin point : Rising edge of CK - CK defined by
the end point of ODTLcwn4 or ODTLcwn8
CK
CK
V
TT
t
t
ADC
ADC
End point Extrapolated point at VRTT_Nom
VRTT_Nom
VRTT_Nom
T
SW21
T
End point
T
DQ, DM
DQS , DQS
TDQS , TDQS
SW22
Extrapolated point
at VRTT_Nom
V
SW2
SW11
T
SW12
V
SW1
End point Extrapolated point at VRTT_Wr
VRTT_Wr
V
SSQ
Figure 18. Definition of tADC
Rev. 1.0 February 2009
Page 28 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
10.0 IDD Specification Parameters and Test Conditions
10.1 IDD Measurement Conditions
In this chapter, IDD and IDDQ measurement conditions such as test load and patterns are defined. Figure 19 shows the setup and test load for IDD and
IDDQ measurements.
- IDD currents (such as IDD0, IDD1, IDD2N, IDD2NT, IDD2P0, IDD2P1, IDD2Q, IDD3N, IDD3P, IDD4R, IDD4W, IDD5B, IDD6, IDD6ET, IDD6TC and
IDD7) are measured as time-averaged currents with all VDD balls of the DDR3 SDRAM under test tied together. Any IDDQ current is not included in
IDD currents.
- IDDQ currents (such as IDDQ2NT and IDDQ4R) are measured as time-averaged currents with all VDDQ balls of the DDR3 SDRAM under test tied
together. Any IDD current is not included in IDDQ currents.
Attention : IDDQ values cannot be directly used to calculate IO power of the DDR3 SDRAM. They can be used to support correlation of simulated IO
power to actual IO power as outlined in Figure 20. In DRAM module application, IDDQ cannot be measured separately since VDD and VDDQ
are using one merged-power layer in Module PCB.
For IDD and IDDQ measurements, the following definitions apply :
- "0" and "LOW" is defined as VIN <= VILAC(max).
- "1" and "HIGH" is defined as VIN >= VIHAC(min).
- "FLOATING" is defined as inputs are VREF = VDD / 2.
- Timings used for IDD and IDDQ Measurement-Loop Patterns are provided in Table 30.
- Basic IDD and IDDQ Measurement Conditions are described in Table 31.
- Detailed IDD and IDDQ Measurement-Loop Patterns are described in Table 32 on page 33 through Table 39.
- IDD Measurements are done after properly initializing the DDR3 SDRAM. This includes but is not limited to setting
RON = RZQ/7 (34 Ohm in MR1);
Qoff = 0B (Output Buffer enabled in MR1);
RTT_Nom = RZQ/6 (40 Ohm in MR1);
RTT_Wr = RZQ/2 (120 Ohm in MR2);
TDQS Feature disabled in MR1
- Attention : The IDD and IDDQ Measurement-Loop Patterns need to be executed at least one time before actual IDD or IDDQ measurement is started.
- Define D = {CS, RAS, CAS, WE} := {HIGH, LOW, LOW, LOW}
- Define D = {CS, RAS, CAS, WE} := {HIGH, HIGH, HIGH, HIGH}
[ Table 30 ] Timing used for IDD and IDDQ Measured - Loop Patterns
DDR3-800
DDR3-1066
DDR3-1333
DDR3-1600
Parameter Bin
Unit
5-5-5 6-6-6 6-6-6 7-7-7 8-8-8 7-7-7 8-8-8 9-9-9 10-10-10 8-8-8 9-9-9 10-10-10 11-11-11
tCKmin(IDD)
2.5
1.875
7
1.5
1.25
10
ns
CL(IDD)
5
5
6
6
6
6
8
8
7
7
8
8
9
9
10
10
34
8
8
9
9
11
11
39
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
tRCDmin(IDD)
tRCmin(IDD)
tRASmin(IDD)
tRPmin(IDD)
7
10
38
20
21
26
27
20
7
28
31
32
33
36
37
15
24
28
5
6
6
8
7
8
9
10
8
9
10
11
x4/x8
x16
16
20
4
20
27
4
20
30
4
24
32
5
tFAW(IDD)
tRRD(IDD)
x4/x8
x16
4
6
5
6
tRFC(IDD) - 512Mb
tRFC(IDD) - 1Gb
tRFC(IDD) - 2Gb
tRFC(IDD) - 4Gb
tRFC(IDD) - 8Gb
36
44
64
120
140
48
59
86
160
187
60
74
72
88
107
200
234
128
240
280
Rev. 1.0 February 2009
Page 29 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
(optional)
I
I
DDQ
DD
V
V
DDQ
DD
RESET
CK/CK
CKE
CS
RAS, CAS, WE
DQS, DQS
DQ, DM,
TDQS, TDQS
R
= 25 Ohm
V
TT
/2
DDQ
A, BA
ODT
ZQ
V
V
SSQ
SS
[Note: DIMM level Output test load condition may be different from above]
Figure 19. Measurement Setup and Test Load for IDD and IDDQ (optional) Measurements
Application specific
memory channel
environment
IDDQ
Test Load
Channel
IO Power
Simulation
IDDQ
Measurement
IDDQ
Simulation
Correlation
Correction
Channel IO Power
Number
Figure 20. Correlation from simulated Channel IO Power to actual Channel IO Power supported by IDDQ Measurement.
Rev. 1.0 February 2009
Page 30 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
[ Table 31 ] Basic IDD and IDDQ Measurement Conditions
Symbol
Description
Operating One Bank Active-Precharge Current
CKE: High; External clock: On; tCK, nRC, nRAS, CL: see Table 30 ; BL: 8 ; AL: 0; CS: High between ACT and PRE; Command, Address, Bank Address
Inputs: partially toggling according to Table 32 ; Data IO: MID-LEVEL; DM:stable at 0; Bank Activity: Cycling with one bank active at a time: 0,0,1,1,2,2,...
a)
IDD0
b)
(see Table32); Output Buffer and RTT: Enabled in Mode Registers ; ODT Signal: stable at 0; Pattern Details: see Table 32
Operating One Bank Active-Read-Precharge Current
CKE: High; External clock: On; tCK, nRC, nRAS, nRCD, CL: see Table 30 ; BL: 8 ; AL: 0; CS: High between ACT, RD and PRE; Command, Address,
Bank Address Inputs, Data IO: partially toggling according to Table 33 ; DM:stable at 0; Bank Activity: Cycling with one bank active at a time: 0,0,1,1,2,2,...
a)
IDD1
b)
(see Table33); Output Buffer and RTT: Enabled in Mode Registers ; ODT Signal: stable at 0; Pattern Details: see Table 33
Precharge Standby Current
a)
CKE: High; External clock: On; tCK, CL: see Table 30 ; BL: 8 ; AL: 0; CS: stable at 1; Command, Address, Bank Address Inputs: partially toggling
according to Table 34 ; Data IO: MID-LEVEL; DM:stable at 0; Bank Activity: all banks closed; Output Buffer and RTT: Enabled in Mode Registers ; ODT
Signal: stable at 0; Pattern Details: see Table 34
IDD2N
DD2NT
b)
Precharge Standby ODT Current
a)
CKE: High; External clock: On; tCK, CL: see Table 30 ; BL: 8 ; AL: 0; CS: stable at 1; Command, Address, Bank Address Inputs: partially toggling
according to Table 35 ; Data IO: MID-LEVEL;DM:stable at 0; Bank Activity: all banks closed; Output Buffer and RTT: Enabled in Mode Registers ; ODT
Signal: toggling according to Table 35 ; Pattern Details: see Table 35
b)
DDQ2NT
(optional)
Precharge Standby ODT IDDQ Current
Same definition like for IDD2NT, however measuring IDDQ current instead of IDD current
Precharge Power-Down Current Slow Exit
CKE: Low; External clock: On; tCK, CL: see Table 30 ; BL: 8 ; AL: 0; CS: stable at 1; Command, Address, Bank Address Inputs: stable at 0; Data IO:
a)
IDD2P0
b)
MID-LEVEL; DM:stable at 0; Bank Activity: all banks closed; Output Buffer and RTT: Enabled in Mode Registers ; ODT Signal: stable at 0; Precharge
c)
Power Down Mode: Slow Exi
Precharge Power-Down Current Fast Exit
CKE: Low; External clock: On; tCK, CL: see Table 30 ; BL: 8 ; AL: 0; CS: stable at 1; Command, Address, Bank Address Inputs: stable at 0; Data IO:
a)
IDD2P1
IDD2Q
IDD3N
IDD3P
b)
MID-LEVEL; DM:stable at 0; Bank Activity: all banks closed; Output Buffer and RTT: Enabled in Mode Registers ; ODT Signal: stable at 0; Precharge
c)
Power Down Mode: Fast Exit
Precharge Quiet Standby Current
a)
CKE: High; External clock: On; tCK, CL: see Table 30 ; BL: 8 ; AL: 0; CS: stable at 1; Command, Address, Bank Address Inputs: stable at 0; Data IO:
MID-LEVEL; DM:stable at 0;Bank Activity: all banks closed; Output Buffer and RTT: Enabled in Mode Registers ; ODT Signal: stable at 0
b)
Active Standby Current
a)
CKE: High; External clock: On; tCK, CL: see Table 30 ; BL: 8 ; AL: 0; CS: stable at 1; Command, Address, Bank Address Inputs: partially toggling
according to Table 34 ; Data IO: MID-LEVEL; DM:stable at 0;Bank Activity: all banks open; Output Buffer and RTT: Enabled in Mode Registers ; ODT Sig-
nal: stable at 0; Pattern Details: see Table 34
b)
Active Power-Down Current
a)
CKE: Low; External clock: On; tCK, CL: see Table 30 ; BL: 8 ; AL: 0; CS: stable at 1; Command, Address, Bank Address Inputs: stable at 0; Data IO:
MID-LEVEL;DM:stable at 0; Bank Activity: all banks open; Output Buffer and RTT: Enabled in Mode Registers ; ODT Signal: stable at 0
b)
Operating Burst Read Current
a)
CKE: High; External clock: On; tCK, CL: see Table 30 ; BL: 8 ; AL: 0; CS: High between RD; Command, Address, Bank Address Inputs: partially toggling
IDD4R
according to Table 36 ; Data IO: seamless read data burst with different data between one burst and the next one according to Table 36 ; DM:stable at 0; Bank
Activity: all banks open, RD commands cycling through banks: 0,0,1,1,2,2,... (see Table 7 on page 10); Output Buffer and RTT: Enabled in Mode Regis-
b)
ters ; ODT Signal: stable at 0; Pattern Details: see Table 36
IDDQ4R
(optional)
Operating Burst Read IDDQ Current
Same definition like for IDD4R, however measuring IDDQ current instead of IDD current
Operating Burst Write Current
a)
CKE: High; External clock: On; tCK, CL: see Table 30 ; BL: 8 ; AL: 0; CS: High between WR; Command, Address, Bank Address Inputs: partially tog-
gling according to Table 37 ; Data IO: seamless write data burst with different data between one burst and the next one according to Table 37; DM: stable at 0;
Bank Activity: all banks open, WR commands cycling through banks: 0,0,1,1,2,2,... (see Table 37); Output Buffer and RTT: Enabled in Mode Registers
ODT Signal: stable at HIGH; Pattern Details: see Table 37
IDD4W
b)
;
Burst Refresh Current
a)
CKE: High; External clock: On; tCK, CL, nRFC: see Table 30 ; BL: 8 ; AL: 0; CS: High between REF; Command, Address, Bank Address Inputs: partially
toggling according to Table 38 ; Data IO: MID-LEVEL;DM:stable at 0; Bank Activity: REF command every nRFC (see Table 38); Output Buffer and RTT:
Enabled in Mode Registers ; ODT Signal: stable at 0; Pattern Details: see Table 38
IDD5B
IDD6
b)
Self Refresh Current: Normal Temperature Range
d)
e)
TCASE: 0 - 85°C; Auto Self-Refresh (ASR): Disabled ; Self-Refresh Temperature Range (SRT): Normal ; CKE: Low; External clock: Off; CK and CK:
a)
LOW; CL: see Table 30 ; BL: 8 ; AL: 0; CS, Command, Address, Bank Address, Data IO: MID-LEVEL;DM:stable at 0; Bank Activity: Self-Refresh operation;
b)
Output Buffer and RTT: Enabled in Mode Registers ; ODT Signal: MID-LEVEL
Rev. 1.0 February 2009
Page 31 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
[ Table 31 ] Basic IDD and IDDQ Measurement Conditions
Symbol
Description
f
Self-Refresh Current: Extended Temperature Range (optional) )
d)
e)
TCASE: 0 - 95°C; Auto Self-Refresh (ASR): Disabled ; Self-Refresh Temperature Range (SRT): Extended ; CKE: Low; External clock: Off; CK and CK:
IDD6ET
a)
LOW; CL: see Table 30 ; BL: 8 ; AL: 0; CS, Command, Address, Bank Address, Data IO: MID-LEVEL;DM:stable at 0; Bank Activity: Extended Temperature
b)
Self-Refresh operation; Output Buffer and RTT: Enabled in Mode Registers ; ODT Signal: MID-LEVEL
f
Auto Self-Refresh Current (optional) )
d)
e)
TCASE: 0 - 95°C; Auto Self-Refresh (ASR): Enabled ; Self-Refresh Temperature Range (SRT): Normal ; CKE: Low; External clock: Off; CK and CK:
IDD6TC
IDD7
a)
LOW; CL: see Table 30 ; BL: 8 ; AL: 0; CS, Command, Address, Bank Address, Data IO: MID-LEVEL; DM:stable at 0; Bank Activity: Auto
b)
Self-Refresh operation; Output Buffer and RTT: Enabled in Mode Registers ; ODT Signal: MID-LEVEL
Operating Bank Interleave Read Current
a)
CKE: High; External clock: On; tCK, nRC, nRAS, nRCD, nRRD, nFAW, CL: see Table 30 ; BL: 8 ; AL: CL-1; CS: High between ACT and RDA; Command,
Address, Bank Address Inputs: partially toggling according to Table 39 ; Data IO: read data bursts with different data between one burst and the next one
according to Table 39 ; DM:stable at 0; Bank Activity: two times interleaved cycling through banks (0, 1, ...7) with different addressing, see Table 39 ; Output
b)
Buffer and RTT: Enabled in Mode Registers ; ODT Signal: stable at 0; Pattern Details: see Table 39
a) Burst Length: BL8 fixed by MRS: set MR0 A[1,0]=00B
b) Output Buffer Enable: set MR1 A[12] = 0B; set MR1 A[5,1] = 01B; RTT_Nom enable: set MR1 A[9,6,2] = 011B; RTT_Wr enable: set MR2 A[10,9] = 10B
c) Precharge Power Down Mode: set MR0 A12=0B for Slow Exit or MR0 A12=1B for Fast Exit
d) Auto Self-Refresh (ASR): set MR2 A6 = 0B to disable or 1B to enable feature
e) Self-Refresh Temperature Range (SRT): set MR2 A7=0B for normal or 1B for extended temperature range
f) Refer to DRAM supplier data sheet and/or DIMM SPD to determine if optional features or requirements are supported by DDR3 SDRAM device
g) Read Burst type : Nibble Sequential, set MR0 A[3]=0B
Rev. 1.0 February 2009
Page 32 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
[ Table 32 ] IDD0 Measurement - Loop Pattern1
0
0
1,2
ACT
D, D
D, D
0
1
1
0
0
1
1
0
1
1
0
1
0
0
0
0
0
0
00
00
00
0
0
0
0
0
0
0
0
0
0
0
0
-
-
-
3,4
...
repeat pattern 1...4 until nRAS - 1, truncate if necessary
PRE
repeat pattern 1...4 until nRC - 1, truncate if necessary
nRAS
0
0
1
0
0
0
00
0
0
0
0
-
...
1*nRC + 0
1*nRC + 1, 2
1*nRC + 3, 4
...
ACT
D, D
D, D
0
1
1
0
0
1
1
0
1
1
0
1
0
0
0
0
0
0
00
00
00
0
0
0
0
0
0
F
F
F
0
0
0
-
-
-
repeat pattern 1...4 until 1*nRC + nRAS - 1, truncate if necessary
PRE 00
1*nRC + nRAS
...
0
0
1
0
0
0
0
0
F
0
repeat 1...4 until 2*nRC - 1, truncate if necessary
repeat Sub-Loop 0, use BA[2:0] = 1 instead
repeat Sub-Loop 0, use BA[2:0] = 2 instead
repeat Sub-Loop 0, use BA[2:0] = 3 instead
repeat Sub-Loop 0, use BA[2:0] = 4 instead
repeat Sub-Loop 0, use BA[2:0] = 5 instead
repeat Sub-Loop 0, use BA[2:0] = 6 instead
repeat Sub-Loop 0, use BA[2:0] = 7 instead
1
2
3
4
5
6
7
2*nRC
4*nRC
6*nRC
8*nRC
10*nRC
12*nRC
14*nRC
Note :
1. DM must be driven LOW all the time. DQS, DQS are MID-LEVEL.
2. DQ signals are MID-LEVEL.
Rev. 1.0 February 2009
Page 33 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
[ Table 33 ] IDD1 Measurement - Loop Pattern1
0
0
1,2
ACT
D, D
D, D
0
1
1
0
0
1
1
0
1
1
0
1
0
0
0
0
0
0
00
00
00
0
0
0
0
0
0
0
0
0
0
0
0
-
-
-
3,4
...
repeat pattern 1...4 until nRCD- 1, truncate if necessary
RD
repeat pattern 1...4 until nRAS - 1, truncate if necessary
PRE
repeat pattern 1...4 until nRC - 1, truncate if necessary
nRCD
...
0
1
0
1
0
0
00
00
0
0
0
0
0
0
0
0
00000000
-
nRAS
0
0
1
0
0
0
...
1*nRC+0
1*nRC + 1, 2
1*nRC + 3, 4
...
ACT
D, D
D, D
0
1
1
0
0
1
1
0
1
1
0
1
0
0
0
0
0
0
00
00
00
0
0
0
0
0
0
F
F
F
0
0
0
-
-
-
repeat pattern nRC + 1,..., 4 until nRC + nRCD - 1, truncate if necessary
RD 00
repeat pattern nRC + 1,..., 4 until nRC +nRAS - 1, truncate if necessary
PRE 00 0
1*nRC + nRCD
...
0
1
0
1
0
0
0
0
F
F
0
0
00110011
-
1*nRC + nRAS
...
0
0
1
0
0
0
0
repeat pattern nRC + 1,..., 4 until 2 * nRC - 1, truncate if necessary
repeat Sub-Loop 0, use BA[2:0] = 1 instead
repeat Sub-Loop 0, use BA[2:0] = 2 instead
repeat Sub-Loop 0, use BA[2:0] = 3 instead
repeat Sub-Loop 0, use BA[2:0] = 4 instead
repeat Sub-Loop 0, use BA[2:0] = 5 instead
repeat Sub-Loop 0, use BA[2:0] = 6 instead
repeat Sub-Loop 0, use BA[2:0] = 7 instead
1
2
3
4
5
6
7
2*nRC
4*nRC
6*nRC
8*nRC
10*nRC
12*nRC
14*nRC
Note :
1. DM must be driven LOW all the time. DQS, DQS are used according to RD Commands, otherwise MID-LEVEL.
2. Burst Sequence driven on each DQ signal by Read Command. Outside burst operation, DQ signals are MID-LEVEL.
[ Table 34 ] IDD2 and IDD3N Measurement - Loop Pattern1
0
0
D
D
D
D
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
0
0
0
0
0
0
00
00
00
00
0
0
0
0
0
0
0
0
0
0
F
F
0
0
0
0
-
-
-
-
1
2
3
1
2
3
4
5
6
7
4-7
repeat Sub-Loop 0, use BA[2:0] = 1 instead
repeat Sub-Loop 0, use BA[2:0] = 2 instead
repeat Sub-Loop 0, use BA[2:0] = 3 instead
repeat Sub-Loop 0, use BA[2:0] = 4 instead
repeat Sub-Loop 0, use BA[2:0] = 5 instead
repeat Sub-Loop 0, use BA[2:0] = 6 instead
repeat Sub-Loop 0, use BA[2:0] = 7 instead
8-11
12-15
16-19
20-23
24-27
28-31
Note :
1. DM must be driven Low all the time. DQS, DQS are MID-LEVEL.
2. DQ signals are MID-LEVEL.
Rev. 1.0 February 2009
Page 34 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
[ Table 35 ] IDD2NT and IDDQ2NT Measurement - Loop Pattern1
0
0
D
D
D
D
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
0
0
0
0
0
0
00
00
00
00
0
0
0
0
0
0
0
0
0
0
F
F
0
0
0
0
-
1
2
3
1
2
3
4
5
6
7
4-7
repeat Sub-Loop 0, but ODT = 0 and BA[2:0] = 1
repeat Sub-Loop 0, but ODT = 1 and BA[2:0] = 2
repeat Sub-Loop 0, but ODT = 1 and BA[2:0] = 3
repeat Sub-Loop 0, but ODT = 0 and BA[2:0] = 4
repeat Sub-Loop 0, but ODT = 0 and BA[2:0] = 5
repeat Sub-Loop 0, but ODT = 1 and BA[2:0] = 6
repeat Sub-Loop 0, but ODT = 1 and BA[2:0] = 7
8-11
12-15
16-19
20-23
24-27
28-31
Note :
1. DM must be driven Low all the time. DQS, DQS are MID-LEVEL.
2. DQ signals are MID-LEVEL.
[ Table 36 ] IDD4R and IDDQ4R Measurement - Loop Pattern1
0
0
RD
D
0
1
1
0
1
1
1
0
1
1
0
1
0
0
1
0
0
1
1
0
1
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
00
00
00
00
00
00
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
F
F
F
0
0
0
0
0
0
00000000
1
-
2,3
D,D
RD
D
-
4
00110011
5
-
-
6,7
D,D
1
2
3
4
5
6
7
8-15
16-23
24-31
32-39
40-47
48-55
56-63
repeat Sub-Loop 0, but BA[2:0] = 1
repeat Sub-Loop 0, but BA[2:0] = 2
repeat Sub-Loop 0, but BA[2:0] = 3
repeat Sub-Loop 0, but BA[2:0] = 4
repeat Sub-Loop 0, but BA[2:0] = 5
repeat Sub-Loop 0, but BA[2:0] = 6
repeat Sub-Loop 0, but BA[2:0] = 7
Note :
1. DM must be driven LOW all the time. DQS, DQS are used according to WR Commands, otherwise MID-LEVEL.
2. Burst Sequence driven on each DQ signal by Write Command. Outside burst operation, DQ signals are MID-LEVEL.
Rev. 1.0 February 2009
Page 35 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
[ Table 37 ] IDD4W Measurement - Loop Pattern1
0
0
WR
D
0
1
1
0
1
1
1
0
1
1
0
1
0
0
1
0
0
1
0
0
1
0
0
1
1
1
1
1
1
1
0
0
0
0
0
0
00
00
00
00
00
00
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
F
F
F
0
0
0
0
0
0
00000000
1
-
2,3
D,D
WR
D
-
4
00110011
5
-
-
6,7
D,D
1
2
3
4
5
6
7
8-15
16-23
24-31
32-39
40-47
48-55
56-63
repeat Sub-Loop 0, but BA[2:0] = 1
repeat Sub-Loop 0, but BA[2:0] = 2
repeat Sub-Loop 0, but BA[2:0] = 3
repeat Sub-Loop 0, but BA[2:0] = 4
repeat Sub-Loop 0, but BA[2:0] = 5
repeat Sub-Loop 0, but BA[2:0] = 6
repeat Sub-Loop 0, but BA[2:0] = 7
Note :
1. DM must be driven LOW all the time. DQS, DQS are used according to WR Commands, otherwise MID-LEVEL.
2. Burst Sequence driven on each DQ signal by Write Command. Outside burst operation, DQ signals are MID-LEVEL.
[ Table 38 ] IDD5B Measurement - Loop Pattern1
0
1
0
1,2
REF
D
0
1
1
0
0
1
0
0
1
1
0
1
0
0
0
0
0
0
00
00
00
0
0
0
0
0
0
0
0
F
0
0
0
-
-
-
3,4
D,D
5...8
repeat cycles 1...4, but BA[2:0] = 1
repeat cycles 1...4, but BA[2:0] = 2
repeat cycles 1...4, but BA[2:0] = 3
repeat cycles 1...4, but BA[2:0] = 4
repeat cycles 1...4, but BA[2:0] = 5
repeat cycles 1...4, but BA[2:0] = 6
repeat cycles 1...4, but BA[2:0] = 7
9...12
13...16
17...20
21...24
25...28
29...32
33...nRFC - 1
2
repeat Sub-Loop 1, until nRFC - 1. Truncate, if necessary.
Note :
1. DM must be driven LOW all the time. DQS, DQS are MID-LEVEL.
2. DQ signals are MID-LEVEL.
Rev. 1.0 February 2009
Page 36 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
[ Table 39 ] IDD7 Measurement - Loop Pattern1
0
1
ACT
RDA
D
0
0
1
0
1
0
1
0
0
1
1
0
0
0
0
0
0
0
00
00
00
0
1
0
0
0
0
0
0
0
0
0
0
-
00000000
-
0
1
2
...
repeat above D Command until nRRD - 1
nRRD
nRRD + 1
nRRD + 2
...
ACT
RDA
D
0
0
1
0
1
0
1
0
0
1
1
0
0
0
0
1
1
1
00
00
00
0
1
0
0
0
0
F
F
F
0
0
0
-
00110011
-
repeat above D Command until 2*nRRD-1
repeat Sub-Loop 0, but BA[2:0] = 2
repeat Sub-Loop 1, but BA[2:0] = 3
2
3
2 * nRRD
3 * nRRD
D
1
0
0
0
0
3
00
0
0
F
F
0
0
-
-
4
4 * nRRD
Assert and repeat above D Command until nFAW - 1, if necessary
repeat Sub-Loop 0, but BA[2:0] = 4
repeat Sub-Loop 1, but BA[2:0] = 5
repeat Sub-Loop 0, but BA[2:0] = 6
repeat Sub-Loop 1, but BA[2:0] = 7
5
6
7
8
nFAW
nFAW+nRRD
nFAW+2*nRRD
nFAW+3*nRRD
D
1
0
0
0
0
7
00
0
0
9
nFAW+4*nRRD
Assert and repeat above D Command until 2*nFAW - 1, if necessary
2*nFAW+0
2*nFAW+1
ACT
RDA
D
0
0
1
0
1
0
1
0
0
1
1
0
0
0
0
0
0
0
00
00
00
0
1
0
0
0
0
F
F
F
0
0
0
-
00110011
-
10
2*nFAW+2
Repeat above D Command until 2*nFAW + nRRD - 1
2*nFAW+nRRD
ACT
RDA
D
0
0
1
0
1
0
1
0
0
1
1
0
0
0
0
1
1
1
00
00
00
0
1
0
0
0
0
0
0
0
0
0
0
-
2*nFAW+nRRD+1
00000000
-
11
2*nFAW+nRRD+2
Repeat above D Command until 2*nFAW + 2*nRRD - 1
repeat Sub-Loop 10, but BA[2:0] = 2
repeat Sub-Loop 11, but BA[2:0] = 3
12
13
2*nFAW+2*nRRD
2*nFAW+3*nRRD
D
1
0
0
0
0
3
00
0
0
0
0
0
-
-
14
2*nFAW+4*nRRD
Assert and repeat above D Command until 3*nFAW - 1, if necessary
repeat Sub-Loop 10, but BA[2:0] = 4
repeat Sub-Loop 11, but BA[2:0] = 5
repeat Sub-Loop 10, but BA[2:0] = 6
repeat Sub-Loop 11, but BA[2:0] = 7
15
16
17
18
3*nFAW
3*nFAW+nRRD
3*nFAW+2*nRRD
3*nFAW+3*nRRD
D
1
0
0
0
0
7
00
0
0
0
19
3*nFAW+4*nRRD
Assert and repeat above D Command until 4*nFAW - 1, if necessary
Note :
1. DM must be driven LOW all the time. DQS, DQS are used according to RD Commands, otherwise MID-LEVEL.
2. Burst Sequence driven on each DQ signal by Read Command. Outside burst operation. DQ signals are MID-LEVEL.
Rev. 1.0 February 2009
Page 37 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
11.0 1Gb DDR3 SDRAM E-die IDD Specification Table
[ Table 40 ] IDD Specification for 1Gb DDR3 E-die
256Mx4 (K4B1G0446E)
Symbol
DDR3-800
6-6-6
55
DDR3-1066
7-7-7
60
DDR3-1333
9-9-9
65
DDR3-1600
TBD
TBD
Unit
Notes
IDD0
IDD1
IDD2P0(slow exit)
IDD2P1(fast exit)
IDD2N
IDD2NT
IDD2Q
IDD3P(fast exit)
IDD3N
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
70
10
25
30
30
25
25
40
85
85
150
10
170
75
10
25
30
35
30
25
45
100
105
150
10
80
10
25
35
40
35
25
50
115
125
160
10
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
IDD4R
IDD4W
IDD5B
IDD6
IDD7
180
225
TBD
128Mx8 (K4B1G0846E)
Symbol
DDR3-800
6-6-6
55
DDR3-1066
7-7-7
60
DDR3-1333
9-9-9
65
DDR3-1600
TBD
TBD
Unit
Notes
IDD0
IDD1
IDD2P0(slow exit)
IDD2P1(fast exit)
IDD2N
IDD2NT
IDD2Q
IDD3P(fast exit)
IDD3N
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
70
10
25
30
30
25
25
40
95
85
150
10
170
75
10
25
30
35
30
25
45
110
115
150
10
80
10
25
35
40
35
25
50
125
135
160
10
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
IDD4R
IDD4W
IDD5B
IDD6
IDD7
185
230
TBD
Rev. 1.0 February 2009
Page 38 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
[ Table 40 ] IDD Specification for 1Gb DDR3 E-die
64Mx16 (K4B1G1646E)
Symbol
DDR3-800
6-6-6
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
DDR3-1066
DDR3-1333
9-9-9
70
DDR3-1600
TBD
TBD
Unit
Notes
7-7-7
65
85
10
25
30
35
30
25
IDD0
IDD1
IDD2P0(slow exit)
IDD2P1(fast exit)
IDD2N
IDD2NT
IDD2Q
IDD3P(fast exit)
IDD3N
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
90
10
25
35
40
35
27
50
160
155
160
10
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
45
IDD4R
IDD4W
IDD5B
IDD6
130
130
150
10
IDD7
200
240
TBD
12.0 Input/Output Capacitance
Rev. 1.0 February 2009
Page 39 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
[ Table 41 ] Input/Output Capacitance
DDR3-800
DDR3-1066
DDR3-1333
DDR3-1600
Parameter
Symbol
Units Notes
Min
Max
Min
Max
Min
Max
Min
Max
Input/output capacitance
CIO
CCK
1.5
0.8
0
3.0
1.5
2.7
1.6
0.15
1.5
0.2
0.3
0.5
1.5
2.5
1.4
1.5
2.3
pF
pF
pF
pF
pF
pF
1,2,3
2,3
(DQ, DM, DQS, DQS, TDQS, TDQS)
Input capacitance
(CK and CK)
1.6
0.15
1.5
0.2
0.3
0.8
0
0.8
0
0.8
0
1.4
0.15
1.3
Input capacitance delta
(CK and CK)
CDCK
0.15
1.3
2,3,4
2,3,6
2,3,5
2,3,7,8
Input capacitance
(All other input-only pins)
CI
0.75
0
0.75
0
0.75
0
0.75
0
Input capacitance delta
(DQS and DQS)
CDDQS
CDI_CTRL
CDI_ADD_CMD
0.15
0.2
0.15
0.2
Input capacitance delta
(All control input-only pins)
-0.5
-0.5
-0.5
-0.5
-0.4
-0.4
-0.4
-0.4
Input capacitance delta
(all ADD and CMD input-only pins)
0.5
0.4
0.4
pF 2,3,9,10
Input/output capacitance delta
(DQ, DM, DQS, DQS, TDQS, TDQS)
CDIO
CZQ
-0.5
-
0.3
3
-0.5
-
0.3
3
-0.5
-
0.3
3
-0.5
-
0.3
3
pF
pF
2,3,11
Input/output capacitance of ZQ pin
2, 3, 12
Note :
1. Although the DM, TDQS and TDQS pins have different functions, the loading matches DQ and DQS
2. This parameter is not subject to production test. It is verified by design and characterization.
The capacitance is measured according to JEP147("PROCEDURE FOR MEASURING INPUT CAPACITANCE USING A VECTOR NETWORK
ANALYZER( VNA)") with VDD, VDDQ, VSS, VSSQ applied and all other pins floating (except the pin under test, CKE, RESET and ODT as necessary).
V
DD=VDDQ=1.5V, VBIAS=VDD/2 and on-die termination off.
3. This parameter applies to monolithic devices only; stacked/dual-die devices are not covered here
4. Absolute value of CCK-CCK
5. Absolute value of CIO(DQS)-CIO(DQS)
6. CI applies to ODT, CS, CKE, A0-A15, BA0-BA2, RAS, CAS, WE.
7. CDI_CTRL applies to ODT, CS and CKE
8. CDI_CTRL=CI(CTRL)-0.5*(CI(CLK)+CI(CLK))
9. CDI_ADD_CMD applies to A0-A15, BA0-BA2, RAS, CAS and WE
10. CDI_ADD_CMD=CI(ADD_CMD) - 0.5*(CI(CLK)+CI(CLK))
11. CDIO=CIO(DQ,DM) - 0.5*(CIO(DQS)+CIO(DQS))
12. Maximum external load capacitance on ZQ pin: 5pF
13.0 Electrical Characteristics and AC timing for DDR3-800 to DDR3-1600
Rev. 1.0 February 2009
Page 40 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
13.1 Clock Specification
The jitter specified is a random jitter meeting a Gaussian distribution. Input clocks violating the min/max values may result in malfunction of the DDR3
SDRAM device.
13.1.1 Definition for tCK(avg)
tCK(avg) is calculated as the average clock period across any consecutive 200 cycle window, where each clock period is calculated from rising edge to
rising edge.
N
tCKj
N=200
N
∑
j=1
13.1.2 Definition for tCK(abs)
tCK(abs) is the absolute clock period, as measured from one rising edge to the next consecutive rising edge. tCK(abs) is not subject to production test.
13.1.3 Definition for tCH(avg) and tCL(avg)
tCH(avg) is defined as the average high pulse width, as calculated across any consecutive 200 high pulses:
tCL(avg) is defined as the average low pulse width, as calculated across any consecutive 200 low pulses:
N
N
tCHj
tCLj
N x tCK(avg) N=200
∑
N x tCK(avg)
N=200
∑
j=1
j=1
13.1.4 Definition for note for tJIT(per), tJIT(per, Ick)
tJIT(per) is defined as the largest deviation of any single tCK from tCK(avg). tJIT(per) = min/max of {tCKi-tCK(avg) where i=1 to 200}
tJIT(per) defines the single period jitter when the DLL is already locked.
tJIT(per,lck) uses the same definition for single period jitter, during the DLL locking period only.
tJIT(per) and tJIT(per,lck) are not subject to production test.
13.1.5 Definition for tJIT(cc), tJIT(cc, Ick)
tJIT(cc) is defined as the absolute difference in clock period between two consecutive clock cycles: tJIT(cc) = Max of {tCKi+1-tCKi}
tJIT(cc) defines the cycle to cycle jitter when the DLL is already locked.
tJIT(cc,lck) uses the same definition for cycle to cycle jitter, during the DLL locking period only.
tJIT(cc) and tJIT(cc,lck) are not subject to production test.
13.1.6 Definition for tERR(nper)
tERR is defined as the cumulative error across n multiple consecutive cycles from tCK(avg). tERR is not subject to production test.
Rev. 1.0 February 2009
Page 41 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
13.2 Refresh Parameters by Device Density
[ Table 42 ] Refresh parameters by device density
Parameter
All Bank Refresh to active/refresh cmd time
Symbol
tRFC
1Gb
110
7.8
2Gb
160
7.8
4Gb
300
7.8
8Gb
350
7.8
Units
ns
Note
0 °C ≤ TCASE ≤ 85°C
µs
Average periodic refresh interval
tREFI
85 °C < TCASE ≤ 95°C
3.9
3.9
3.9
3.9
µs
1
Note :
1. Users should refer to the DRAM supplier data sheet and/or the DIMM SPD to determine if DDR3 SDRAM devices support the following options or
requirements referred to in this material.
13.3 Speed Bins and CL, tRCD, tRP, tRC and tRAS for corresponding Bin
DDR3 SDRAM Speed Bins include tCK, tRCD, tRP, tRAS and tRC for each corresponding bin.
[ Table 43 ] DDR3-800 Speed Bins
Speed
CL-nRCD-nRP
DDR3-800
6 - 6 - 6
Units
Note
Parameter
Symbol
tAA
min
15
max
20
Internal read command to first data
ACT to internal read or write delay time
PRE command period
ns
ns
tRCD
tRP
15
-
15
-
-
ns
ACT to ACT or REF command period
ACT to PRE command period
CL = 6 / CWL = 5
tRC
52.5
37.5
2.5
ns
tRAS
9*tREFI
3.3
ns
8
tCK(AVG)
ns
1,2,3
Supported CL Settings
6
5
nCK
nCK
Supported CWL Settings
[ Table 44 ] DDR3-1066 Speed Bins
Speed
CL-nRCD-nRP
DDR3-1066
7 - 7 - 7
Units
Note
Parameter
Symbol
tAA
min
13.125
13.125
13.125
50.625
37.5
max
20
Internal read command to first data
ACT to internal read or write delay time
PRE command period
ns
ns
tRCD
-
tRP
-
-
ns
ACT to ACT or REF command period
ACT to PRE command period
tRC
ns
tRAS
9*tREFI
3.3
ns
8
CWL = 5
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
2.5
ns
1,2,3,6
1,2,3,4
4
CL = 6
CL = 7
CL = 8
CWL = 6
CWL = 5
CWL = 6
CWL = 5
CWL = 6
Reserved
Reserved
ns
ns
1.875
1.875
<2.5
<2.5
ns
1,2,3,4
4
Reserved
ns
ns
1,2,3
Supported CL Settings
Supported CWL Settings
6,7,8
5,6
nCK
nCK
Rev. 1.0 February 2009
Page 42 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
[ Table 45 ] DDR3-1333 Speed Bins
Speed
CL-nRCD-nRP
Parameter
DDR3-1333
9 -9 - 9
Units
Note
Symbol
min
max
13.5
Internal read command to first data
ACT to internal read or write delay time
PRE command period
tAA
20
ns
ns
ns
ns
(13.125)5,9
13.5
tRCD
tRP
-
-
-
(13.125)5,9
13.5
(13.125)5,9
49.5
ACT to ACT or REF command period
ACT to PRE command period
tRC
(49.125)5,9
tRAS
36
9*tREFI
3.3
ns
ns
ns
ns
ns
8
1,2,3,7
1,2,3,4,7
4
CWL = 5
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
2.5
CL = 6
CWL = 6
CWL = 7
CWL = 5
Reserved
Reserved
Reserved
4
1.875
<2.5
<2.5
CL = 7
CWL = 6
tCK(AVG)
ns
1,2,3,4,7
(Optional) Note 5,9
Reserved
CWL = 7
CWL = 5
CWL = 6
CWL = 7
CWL = 5,6
CWL = 7
CWL = 5,6
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
ns
ns
1,2,3,4,
Reserved
4
1,2,3,7
1,2,3,4,
4
CL = 8
CL = 9
CL = 10
1.875
ns
Reserved
Reserved
ns
ns
1.5
1.5
<1.875
<1.875
ns
1,2,3,4
4
Reserved
ns
ns
1,2,3
5
CWL = 7
tCK(AVG)
(Optional)
6,7,8,9
5,6,7
ns
Supported CL Settings
Supported CWL Settings
nCK
nCK
Rev. 1.0 February 2009
Page 43 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
[ Table 46 ] DDR3-1600 Speed Bins
Speed
CL-nRCD-nRP
Parameter
DDR3-1600
11-11-11
Units
Note
Symbol
min
max
13.75
Internal read command to first data
ACT to internal read or write delay time
PRE command period
tAA
20
ns
ns
ns
ns
(13.125)5,9
13.75
tRCD
tRP
-
-
-
(13.125)5,9
13.75
(13.125)5,9
48.75
ACT to ACT or REF command period
ACT to PRE command period
tRC
(48.125)5,9
tRAS
35
9*tREFI
3.3
ns
ns
ns
ns
ns
CWL = 5
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
2.5
1,2,3,8
CL = 6
CWL = 6
CWL = 7, 8
CWL = 5
Reserved
Reserved
Reserved
1,2,3,4,8
4
4
1.875
<2.5
CWL = 6
tCK(AVG)
ns
1,2,3,4,8
CL = 7
(Optional) Note 5,9
Reserved
CWL = 7
CWL = 8
CWL = 5
CWL = 6
CWL = 7
CWL = 8
CWL = 5,6
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
ns
ns
ns
ns
ns
ns
ns
1,2,3,4,8
Reserved
4
4
Reserved
1.875
1.5
<2.5
1,2,3,8
1,2,3,4,8
1,2,3,4
4
CL = 8
CL = 9
Reserved
Reserved
Reserved
<1.875
CWL = 7
tCK(AVG)
ns
1,2,3,4,8
(Optional) Note 9,10
TBD
CWL = 8
tCK(AVG)
tCK(AVG)
ns
ns
1,2,3,4
4
CWL = 5,6
Reserved
1.5
<1.875
CL = 10
CL = 11
CWL = 7
tCK(AVG)
ns
1,2,3,8
(Optional) Note 9,10
Reserved
CWL = 8
CWL = 5,6,7
CWL = 8
tCK(AVG)
tCK(AVG)
tCK(AVG)
ns
ns
1,2,3,4
4
Reserved
1.25
<1.5
ns
1,2,3,5
Supported CL Settings
Supported CWL Settings
6,7,8,9,10,11
5,6,7,8
nCK
nCK
Rev. 1.0 February 2009
Page 44 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
13.3.1 Speed Bin Table Notes
Absolute Specification (TOPER; VDDQ = VDD = 1.5V +/- 0.075 V);
Note :
1. The CL setting and CWL setting result in tCK(AVG).MIN and tCK(AVG).MAX requirements. When making a selection of tCK(AVG), both need to be ful-
filled: Requirements from CL setting as well as requirements from CWL setting.
2. tCK(AVG).MIN limits: Since CAS Latency is not purely analog - data and strobe output are synchronized by the DLL - all possible intermediate frequen-
cies may not be guaranteed. An application should use the next smaller JEDEC standard tCK(AVG) value (2.5, 1.875, 1.5, or 1.25 ns) when calculat-
ing CL [nCK] = tAA [ns] / tCK(AVG) [ns], rounding up to the next "SupportedCL".
3. tCK(AVG).MAX limits: Calculate tCK(AVG) = tAA.MAX / CL SELECTED and round the resulting tCK(AVG) down to the next valid speed bin (i.e. 3.3ns
or 2.5ns or 1.875 ns or 1.25 ns). This result is tCK(AVG).MAX corresponding to CL SELECTED.
4. "Reserved" settings are not allowed. User must program a different value.
5. "Optional" settings allow certain devices in the industry to support this setting, however, it is not a mandatory feature. Refer to supplier’s data sheet
and/or the DIMM SPD information if and how this setting is supported.
6. Any DDR3-1066 speed bin also supports functional operation at lower frequencies as shown in the table which are not subject to Production Tests but
verified by Design/Characterization.
7. Any DDR3-1333 speed bin also supports functional operation at lower frequencies as shown in the table which are not subject to Production Tests but
verified by Design/Characterization.
8. Any DDR3-1600 speed bin also supports functional operation at lower frequencies as shown in the table which are not subject to Production Tests but
verified by Design/Characterization.
9. For devices supporting optional downshift to CL=7 and CL=9, tAA/tRCD/tRP min must be 13.125 ns or lower. SPD settings must be programmed to
match. For example, DDR3-1333(CL9) devices supporting downshift to DDR3-1066(CL7) should program 13.125 ns in SPD bytes for tAAmin (Byte 16),
tRCDmin (Byte 18), and tRPmin (Byte 20). DDR3-1600(CL11) devices supporting downshift to DDR3-1333(CL9) or DDR3-1066(CL7) should program
13.125 ns in SPD bytes for tAAmin (Byte16), tRCDmin (Byte 18), and tRPmin (Byte 20). Once tRP (Byte 20) is programmed to 13.125ns, tRCmin (Byte
21,23) also should be programmed accordingly. For example, 49.125ns (tRASmin + tRPmin=36ns+13.125ns) for DDR3-1333(CL9) and 48.125ns (tRAS-
min+tRPmin=35ns+13.125ns) for DDR3-1600(CL11).
Rev. 1.0 February 2009
Page 45 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
14.0 Timing Parameters by Speed Grade
[ Table 47 ] Timing Parameters by Speed Bin
Speed
DDR3-800
DDR3-1066
DDR3-1333
DDR3-1600
Units
Note
Parameter
Symbol
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
Clock Timing
tCK(DLL_OF
F)
Minimum Clock Cycle Time (DLL off mode)
8
-
8
-
8
-
8
-
ns
6
Average Clock Period
Clock Period
tCK(avg)
tCK(abs)
See Speed Bins Table
ps
ps
tCK(avg)min + tCK(avg)max + tCK(avg)min + tCK(avg)max + tCK(avg)min + tCK(avg)max + tCK(avg)min + tCK(avg)max +
tJIT(per)min
tJIT(per)max
tJIT(per)min
tJIT(per)max
tJIT(per)min
tJIT(per)max
tJIT(per)min
tJIT(per)max
Average high pulse width
tCH(avg)
tCL(avg)
0.47
0.53
0.47
0.53
0.47
0.53
0.47
0.53
tCK(avg)
Average low pulse width
0.47
0.53
0.47
0.53
0.47
0.53
0.47
0.53
tCK(avg)
ps
Clock Period Jitter
tJIT(per)
-100
100
-90
90
-80
80
-70
70
Clock Period Jitter during DLL locking period
Cycle to Cycle Period Jitter
tJIT(per, lck)
tJIT(cc)
-90
90
-80
80
-70
70
-60
60
ps
200
180
180
160
160
140
140
120
ps
Cycle to Cycle Period Jitter during DLL locking period
Cumulative error across 2 cycles
Cumulative error across 3 cycles
Cumulative error across 4 cycles
Cumulative error across 5 cycles
Cumulative error across 6 cycles
Cumulative error across 7 cycles
Cumulative error across 8 cycles
Cumulative error across 9 cycles
Cumulative error across 10 cycles
Cumulative error across 11 cycles
Cumulative error across 12 cycles
tJIT(cc, lck)
tERR(2per)
tERR(3per)
tERR(4per)
tERR(5per)
tERR(6per)
tERR(7per)
tERR(8per)
tERR(9per)
tERR(10per)
tERR(11per)
tERR(12per)
ps
- 147
- 175
- 194
- 209
- 222
- 232
- 241
- 249
- 257
- 263
- 269
147
175
194
209
222
232
241
249
257
263
269
- 132
- 157
- 175
- 188
- 200
- 209
- 217
- 224
- 231
- 237
- 242
132
157
175
188
200
209
217
224
231
237
242
- 118
- 140
- 155
- 168
- 177
- 186
- 193
- 200
- 205
- 210
- 215
118
140
155
168
177
186
193
200
205
210
215
-103
-122
-136
-147
-155
-163
-169
-175
-180
-184
-188
103
122
136
147
155
163
169
175
180
184
188
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
tERR(nper)min = (1 + 0.68ln(n))*tJIT(per)min
tERR(nper)max = (1 = 0.68ln(n))*tJIT(per)max
Cumulative error across n = 13, 14 ... 49, 50 cycles
tERR(nper)
ps
24
Absolute clock HIGH pulse width
Absolute clock Low pulse width
tCH(abs)
tCL(abs)
0.43
0.43
-
-
0.43
0.43
-
-
0.43
0.43
-
-
0.43
0.43
-
-
tCK(avg)
tCK(avg)
25
26
Data Timing
DQS,DQS to DQ skew, per group, per access
DQ output hold time from DQS, DQS
DQ low-impedance time from CK, CK
DQ high-impedance time from CK, CK
Data setup time to DQS, DQS referenced to
tDQSQ
tQH
-
200
-
-
150
-
-
125
-
-
100
-
ps
tCK(avg)
ps
13
0.38
-800
-
0.38
-600
-
0.38
-500
-
0.38
-450
-
13, g
tLZ(DQ)
tHZ(DQ)
400
400
300
300
250
250
225
225
13,14, f
13,14, f
ps
tDS(base)
75
-
25
-
30
-
10
ps
d, 17
V
(AC)V (AC) levels
IL
IH
Data hold time to DQS, DQS referenced to
(AC)V (AC) levels
tDH(base)
tDIPW
150
600
100
490
65
-
45
ps
ps
d, 17
28
-
-
-
-
V
IH
IL
DQ and DM Input pulse width for each input
Data Strobe Timing
400
360
-
DQS, DQS READ Preamble
DQS, DQS differential READ Postamble
DQS, DQS output high time
tRPRE
tRPST
tQSH
0.9
0.3
Note 19
0.9
0.3
Note 19
0.9
0.3
0.4
0.4
0.9
0.3
Note 19
0.9
0.3
0.4
0.4
0.9
0.3
Note 19
tCK
tCK
13, 19, g
11, 13, b
13, g
Note 11
Note 11
Note 11
Note 11
0.38
0.38
0.9
-
-
-
-
0.38
0.38
0.9
-
-
-
-
-
-
-
-
-
-
-
-
tCK(avg)
tCK(avg)
tCK
DQS, DQS output low time
tQSL
13, g
DQS, DQS WRITE Preamble
DQS, DQS WRITE Postamble
tWPRE
tWPST
0.3
0.3
tCK
DQS, DQS rising edge output access time from rising
CK, CK
tDQSCK
-400
-800
-
400
400
400
-300
-600
-
300
300
300
-255
-500
-
255
250
250
-225
-450
-
225
225
225
ps
ps
ps
13,f
DQS, DQS low-impedance time (Referenced from RL-1) tLZ(DQS)
13,14,f
12,13,14
DQS, DQS high-impedance time (Referenced from
tHZ(DQS)
RL+BL/2)
DQS, DQS differential input low pulse width
tDQSL
tDQSH
tDQSS
tDSS
0.45
0.45
-0.25
0.2
0.55
0.55
0.25
-
0.45
0.45
-0.25
0.2
0.55
0.55
0.25
-
0.45
0.45
-0.25
0.2
0.55
0.55
0.25
-
0.45
0.45
-0.27
0.18
0.18
0.55
0.55
0.27
-
tCK
29, 31
30, 31
c
DQS, DQS differential input high pulse width
DQS, DQS rising edge to CK, CK rising edge
DQS,DQS falling edge setup time to CK, CK rising edge
DQS,DQS falling edge hold time to CK, CK rising edge
tCK
tCK(avg)
tCK(avg)
tCK(avg)
c, 32
c, 32
tDSH
0.2
-
0.2
-
0.2
-
-
Rev. 1.0 February 2009
Page 46 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
[ Table 47 ] Timing Parameters by Speed Bin
Speed
DDR3-800
DDR3-1066
DDR3-1333
DDR3-1600
Units
Note
Parameter
Command and Address Timing
DLL locking time
Symbol
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
tDLLK
tRTP
512
-
-
512
-
-
512
-
-
512
-
-
nCK
internal READ Command to PRECHARGE Command
delay
max
max
max
max
e
(4nCK,7.5ns)
(4nCK,7.5ns)
(4nCK,7.5ns)
(4nCK,7.5ns)
Delay from start of internal write transaction to internal
read command
max
max
max
max
tWTR
-
-
-
-
e,18
e
(4nCK,7.5ns)
(4nCK,7.5ns)
(4nCK,7.5ns)
(4nCK,7.5ns)
WRITE recovery time
tWR
15
4
-
-
15
4
-
-
15
4
-
-
15
4
-
-
ns
Mode Register Set command cycle time
tMRD
nCK
max
max
max
max
Mode Register Set command update delay
tMOD
(12nCK,15ns
)
-
-
(12nCK,15ns
)
-
(12nCK,15ns
)
-
-
-
-
(12nCK,15ns)
CAS# to CAS# command delay
tCCD
tDAL(min)
tMPRR
tRAS
4
4
-
4
4
nCK
nCK
nCK
ns
Auto precharge write recovery + precharge time
Multi-Purpose Register Recovery Time
ACTIVE to PRECHARGE command period
WR + roundup (tRP / tCK(AVG))
1
-
1
-
1
-
1
-
22
e
See 13.3 " Speed Bins and CL, tRCD, tRP, tRC and tRAS for corresponding Bin" on page 37
max
max
max
max
ACTIVE to ACTIVE command period for 1KB page size
ACTIVE to ACTIVE command period for 2KB page size
tRRD
tRRD
-
-
-
-
-
-
-
-
e
e
(4nCK,10ns)
(4nCK,7.5ns)
(4nCK,6ns)
(4nCK,6ns)
max
max
max
max
(4nCK,10ns)
(4nCK,10ns)
(4nCK,7.5ns)
(4nCK,7.5ns)
Four activate window for 1KB page size
Four activate window for 2KB page size
Command and Address setup time to CK, CK refer-
tFAW
tFAW
40
50
-
-
37.5
50
-
-
30
45
-
-
30
40
-
-
ns
ns
e
e
tIS(base)
tIH(base)
200
275
125
200
65
-
-
TBD
TBD
-
-
ps
ps
b,16
b,16
-
-
-
-
enced to V (AC) / V (AC) levels
IH
IL
Command and Address hold time from CK, CK refer-
enced to V (AC) / V (AC) levels
140
IH
IL
Command and Address setup time to CK, CK refer-
enced to V (AC) / V (AC) levels
tIS(base)
AC150
200 + 150
900
125 + 150
780
65+125
620
-
-
TBD+125
560
-
-
ps
ps
b,16,27
28
-
-
-
-
IH
IL
Control & Address Input pulse width for each input
Calibration Timing
tIPW
Power-up and RESET calibration time
Normal operation Full calibration time
Normal operation short calibration time
Reset Timing
tZQinitI
tZQoper
tZQCS
512
256
64
-
-
-
512
256
64
-
-
-
512
256
64
-
-
-
512
256
64
-
-
-
nCK
nCK
nCK
23
max(5nCK,
max(5nCK,
max(5nCK,
max(5nCK,
Exit Reset from CKE HIGH to a valid command
tXPR
-
-
-
-
tRFC + 10ns)
tRFC + 10ns)
tRFC + 10ns)
tRFC + 10ns)
Self Refresh Timing
Exit Self Refresh to commands not requiring a locked
DLL
max(5nCK,tR
FC + 10ns)
max(5nCK,tR
FC + 10ns)
max(5nCK,tR
FC + 10ns)
max(5nCK,tR
FC + 10ns)
tXS
-
-
-
-
-
-
-
-
-
-
-
-
Exit Self Refresh to commands requiring a locked DLL
tXSDLL
tCKESR
tDLLK(min)
tDLLK(min)
tDLLK(min)
tDLLK(min)
nCK
Minimum CKE low width for Self refresh entry to exit
timing
tCKE(min) +
1tCK
tCKE(min) +
1tCK
tCKE(min) +
1tCK
tCKE(min) +
1tCK
Valid Clock Requirement after Self Refresh Entry
(SRE) or Power-Down Entry (PDE)
max(5nCK,
10ns)
max(5nCK,
10ns)
max(5nCK,
10ns)
max(5nCK,
10ns)
tCKSRE
tCKSRX
-
-
-
-
-
-
-
-
Valid Clock Requirement before Self Refresh Exit
(SRX) or Power-Down Exit (PDX) or Reset Exit
max(5nCK,
10ns)
max(5nCK,
10ns)
max(5nCK,
10ns)
max(5nCK,
10ns)
Rev. 1.0 February 2009
Page 47 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
[ Table 47] Timing Parameters by Speed Bin (Cont.)
Speed
Parameter
Power Down Timing
DDR3-800
DDR3-1066
DDR3-1333
DDR3-1600
Units
Note
Symbol
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
Exit Power Down with DLL on to any valid com-
mand;Exit Precharge Power Down with DLL
frozen to commands not requiring a locked DLL
max
max
max
max
tXP
tXPDLL
tCKE
(3nCK,
7.5ns)
-
-
-
(3nCK,
7.5ns)
-
-
-
-
-
-
-
-
-
(3nCK,6ns)
(3nCK,6ns)
max
(10nCK,
24ns)
max
(10nCK,
24ns)
max
(10nCK,
24ns)
max
(10nCK,
24ns)
Exit Precharge Power Down with DLL frozen to com-
mands requiring a locked DLL
2
max
max
max
max
CKE minimum pulse width
(3nCK,
7.5ns)
(3nCK,
5.625ns)
(3nCK,
5.625ns)
(3nCK,5ns)
Command pass disable delay
tCPDED
tPD
1
-
1
-
1
-
1
-
nCK
tCK
Power Down Entry to Exit Timing
tCKE(min)
9*tREFI
tCKE(min)
9*tREFI
tCKE(min)
9*tREFI
tCKE(min)
9*tREFI
15
20
20
Timing of ACT command to Power Down entry
Timing of PRE command to Power Down entry
Timing of RD/RDA command to Power Down entry
tACTPDEN
tPRPDEN
tRDPDEN
1
1
-
-
-
1
1
-
-
-
1
1
-
-
-
1
1
-
-
-
nCK
nCK
RL + 4 +1
RL + 4 +1
RL + 4 +1
RL + 4 +1
WL + 4
+(tWR/
WL + 4
+(tWR/
WL + 4
+(tWR/
WL + 4
+(tWR/
Timing of WR command to Power Down entry
(BL8OTF, BL8MRS, BL4OTF)
tWRPDEN
tWRAPDEN
tWRPDEN
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
nCK
nCK
nCK
nCK
9
10
9
tCK(avg))
tCK(avg))
tCK(avg))
tCK(avg))
Timing of WRA command to Power Down entry
(BL8OTF, BL8MRS, BL4OTF)
WL + 4
WL + 4
WL + 4
WL + 4 +WR
+1
+WR +1
+WR +1
+WR +1
WL + 2
+(tWR/
WL + 2
+(tWR/
WL + 2
+(tWR/
WL + 2
+(tWR/
Timing of WR command to Power Down entry
(BL4MRS)
tCK(avg))
tCK(avg))
tCK(avg))
tCK(avg))
Timing of WRA command to Power Down entry
(BL4MRS)
WL+2+WR
+1
WL+2+WR
+1
WL+2+WR
+1
WL +2 +WR
+1
tWRAPDEN
tREFPDEN
10
Timing of REF command to Power Down entry
Timing of MRS command to Power Down entry
ODT Timing
1
-
-
1
-
-
1
-
-
1
-
-
20,21
tMRSPDEN tMOD(min)
tMOD(min)
tMOD(min)
tMOD(min)
ODT high time without write command or with write
command and BC4
ODTH4
ODTH8
tAONPD
4
6
2
-
-
4
6
2
-
-
4
6
2
-
-
4
6
2
-
-
nCK
nCK
ns
ODT high time with Write command and BL8
Asynchronous RTT turn-on delay (Power-Down with
DLL frozen)
8.5
8.5
8.5
8.5
Asynchronous RTT turn-off delay (Power-Down with
DLL frozen)
tAOFPD
tAON
2
8.5
400
0.7
0.7
2
8.5
300
0.7
0.7
2
8.5
250
0.7
0.7
2
8.5
225
0.7
0.7
ns
ODT turn-on
-400
0.3
0.3
-300
0.3
0.3
-250
0.3
0.3
-225
0.3
0.3
ps
7,f
8,f
f
RTT_NOM and RTT_WR turn-off time from ODTLoff
reference
tAOF
tCK(avg)
tCK(avg)
RTT dynamic change skew
tADC
Write Leveling Timing
First DQS pulse rising edge after tDQSS margining
mode is programmed
tWLMRD
40
-
40
-
40
-
40
-
tCK
3
3
DQS/DQS delay after tDQS margining mode is pro-
grammed
tWLDQSEN
tWLS
25
-
-
-
25
-
-
-
25
-
-
-
25
-
-
-
tCK
ps
Setup time for tDQSS latch
325
325
245
245
195
195
165
165
Write leveling hold time from rising DQS, DQS cross-
ing to rising CK, CK crossing
tWLH
ps
Write leveling output delay
Write leveling output error
tWLO
0
0
9
2
0
0
9
2
0
0
9
2
0
0
7.5
2
ns
ns
tWLOE
Rev. 1.0 February 2009
Page 48 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
14.1 Jitter Notes
Specific Note a Unit ’tCK(avg)’ represents the actual tCK(avg) of the input clock under operation. Unit ’nCK’ represents one clock cycle of the input
clock, counting the actual clock edges.ex) tMRD = 4 [nCK] means; if one Mode Register Set command is registered at Tm, another
Mode Register Set command may be registered at Tm+4, even if (Tm+4 - Tm) is 4 x tCK(avg) + tERR(4per),min.
Specific Note b These parameters are measured from a command/address signal (CKE, CS, RAS, CAS, WE, ODT, BA0, A0, A1, etc.) transition edge
to its respective clock signal (CK/CK) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT(per),
tJIT(cc), etc.), as the setup and hold are relative to the clock signal crossing that latches the command/address. That is, these param-
eters should be met whether clock jitter is present or not.
Specific Note c These parameters are measured from a data strobe signal (DQS(L/U), DQS(L/U)) crossing to its respective clock signal (CK, CK)
crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT(per), tJIT(cc), etc.), as these are relative to
the clock signal crossing. That is, these parameters should be met whether clock jitter is present or not.
Specific Note d These parameters are measured from a data signal (DM(L/U), DQ(L/U)0, DQ(L/U)1, etc.) transition edge to its respective data strobe
signal (DQS(L/U), DQS(L/U)) crossing. Specific Note e For these parameters, the DDR3 SDRAM device supports tnPARAM [nCK] =
RU{ tPARAM [ns] / tCK(avg) [ns] }, which is in clock cycles, assuming all input clock jitter specifications are satisfied. For example, the
device will support tnRP = RU{tRP / tCK(avg)}, which is in clock cycles, if all input clock jitter specifications are met. This means: For
DDR3-800 6-6-6, of which tRP = 15ns, the device will support tnRP = RU{tRP / tCK(avg)} = 6, as long as the input clock jitter specifi-
cations are met, i.e. Precharge command at Tm and Active command at Tm+6 is valid even if (Tm+6 - Tm) is less than 15ns due to
input clock jitter.
Specific Note f When the device is operated with input clock jitter, this parameter needs to be derated by the actual tERR(mper),act of the input clock,
where 2 <= m <= 12. (output deratings are relative to the SDRAM input clock.)
For example, if the measured jitter into a DDR3-800 SDRAM has tERR(mper),act,min = - 172 ps and tERR(mper),act,max = + 193 ps,
then tDQSCK,min(derated) = tDQSCK,min - tERR(mper),act,max = - 400 ps - 193 ps = - 593 ps and tDQSCK,max(derated) =
tDQSCK,max - tERR(mper),act,min = 400 ps + 172 ps = + 572 ps. Similarly, tLZ(DQ) for DDR3-800 derates to tLZ(DQ),min(derated) =
- 800 ps - 193 ps = - 993 ps and tLZ(DQ),max(derated) = 400 ps + 172 ps = + 572 ps. (Caution on the min/max usage!)
Note that tERR(mper),act,min is the minimum measured value of tERR(nper) where 2 <= n <=
12, and tERR(mper),act,max is the maximum measured value of tERR(nper) where 2 <= n <= 12.
Specific Note g When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT(per),act of the input clock.
(output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR3-800 SDRAM has
tCK(avg),act = 2500 ps, tJIT(per),act,min = - 72 ps and tJIT(per),act,max = + 93 ps, then tRPRE,min(derated) = tRPRE,min +
tJIT(per),act,min = 0.9 x tCK(avg),act + tJIT(per),act,min = 0.9 x 2500 ps - 72 ps = + 2178 ps. Similarly, tQH,min(derated) = tQH,min
+ tJIT(per),act,min = 0.38 x tCK(avg),act + tJIT(per),act,min = 0.38 x 2500 ps - 72 ps = + 878 ps. (Caution on the min/max usage!)
Rev. 1.0 February 2009
Page 49 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
14.2 Timing Parameter Notes
1. Actual value dependant upon measurement level definitions which are TBD.
2. Commands requiring a locked DLL are: READ (and RAP) and synchronous ODT commands.
3. The max values are system dependent.
4. WR as programmed in mode register
5. Value must be rounded-up to next higher integer value
6. There is no maximum cycle time limit besides the need to satisfy the refresh interval, tREFI.
7. For definition of RTT turn-on time tAON see "Device Operation"
8. For definition of RTT turn-off time tAOF see "Device Operation".
9. tWR is defined in ns, for calculation of tWRPDEN it is necessary to round up tWR / tCK to the next integer.
10. WR in clock cycles as programmed in MR0
11. The maximum read postamble is bound by tDQSCK(min) plus tQSH(min) on the left side and tHZ(DQS)max on the right side. See Device Operation.
12. Output timing deratings are relative to the SDRAM input clock. When the device is operated with input clock jitter, this parameter needs to be derated
by TBD
13. Value is valid for RON34
14. Single ended signal parameter. Refer to chapter 8 and chapter 9 for definition and measurement method.
15. tREFI depends on T
OPER
16. tIS(base) and tIH(base) values are for 1V/ns CMD/ADD single-ended slew rate and 2V/ns CK, CK differential slew rate, Note for DQ and DM signals,
V
(DC) = V DQ(DC). FOr input only pins except RESET, V (DC)=V CA(DC).
REF
REF
REF
REF
See "Address/ Command Setup, Hold and Derating" .
17. tDS(base) and tDH(base) values are for 1V/ns DQ single-ended slew rate and 2V/ns DQS, DQS differential slew rate. Note for DQ and DM signals,
V
(DC)= V
DQ(DC). For input only pins except RESET, V
(DC)=V
CA(DC).
REF
REF
REF
REF
See "Data Setup, Hold and Slew Rate Derating".
18. Start of internal write transaction is defined as follows ;
For BL8 (fixed by MRS and on-the-fly) : Rising clock edge 4 clock cycles after WL.
For BC4 (on-the-fly) : Rising clock edge 4 clock cycles after WL
For BC4 (fixed by MRS) : Rising clock edge 2 clock cycles after WL
19. The maximum read preamble is bound by tLZDQS(min) on the left side and tDQSCK(max) on the right side. See "Device Operation"
20. CKE is allowed to be registered low while operations such as row activation, precharge, autoprecharge or refresh are in progress, but power-down
IDD spec will not be applied until finishing those operations.
21. Although CKE is allowed to be registered LOW after a REFRESH command once tREFPDEN(min) is satisfied, there are cases where additional time
such as tXPDLL(min) is also required. See "Device Operation".
22. Defined between end of MPR read burst and MRS which reloads MPR or disables MPR function.
23. One ZQCS command can effectively correct a minimum of 0.5 % (ZQCorrection) of RON and RTT impedance error within 64 nCK for all speed bins assuming
the maximum sensitivities specified in the ’Output Driver Voltage and Temperature Sensitivity’ and ’ODT Voltage and Temperature Sensitivity’ tables. The
appropriate interval between ZQCS commands can be determined from these tables and other application specific parameters.
One method for calculating the interval between ZQCS commands, given the temperature (Tdriftrate) and voltage (Vdriftrate) drift rates that the SDRAM is sub-
ject to in the application, is illustrated. The interval could be defined by the following formula:
ZQCorrection
(TSens x Tdriftrate) + (VSens x Vdriftrate)
where TSens = max(dRTTdT, dRONdTM) and VSens = max(dRTTdV, dRONdVM) define the SDRAM temperature and voltage sensitivities.
For example, if TSens = 1.5% /°C, VSens = 0.15% / mV, Tdriftrate = 1°C / sec and Vdriftrate = 15 mV / sec, then the interval between ZQCS commands is calcu-
lated as:
0.5
~
~
= 0.133
128ms
(1.5 x 1) + (0.15 x 15)
24. n = from 13 cycles to 50 cycles. This row defines 38 parameters.
25. tCH(abs) is the absolute instantaneous clock high pulse width, as measured from one rising edge to the following falling edge.
26. tCL(abs) is the absolute instantaneous clock low pulse width, as measured from one falling edge to the following rising edge.
27. The tIS(base) AC150 specifications are adjusted from the tIS(base) specification by adding an additional 100 ps of derating to accommodate for the lower alter-
nate threshold of 150 mV and another 25 ps to account for the earlier reference point [(175 mv - 150 mV) / 1 V/ns].
28. Pulse width of a input signal is defined as the width between the first crossing of V
(DC) and the consecutive crossing of V
(DC)
REF
REF
29. tDQSL describes the instantaneous differential input low pulse width on DQS-DQS, as measured from one falling edge to the next consecutive rising edge.
30. tDQSH describes the instantaneous differential input high pulse width on DQS-DQS, as measured from one rising edge to the next consecutive falling edge.
31. tDQSH, act + tDQSL, act = 1 tCK, act ; with tXYZ, act being the actual measured value of the respective timing parameter in the application.
32. tDSH, act + tDSS, act = 1 tCK, act ; with tXYZ, act being the actual measured value of the respective timing parameter in the application.
Rev. 1.0 February 2009
Page 50 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
14.3 Address/Command Setup, Hold and Derating :
For all input signals the total tIS (setup time) and tIH (hold time) required is calculated by adding the data sheet tIS(base) and tIH(base) value (see Table
48) to the ∆tIS and ∆tIH derating value (see Table 49) respectively.
Example: tIS (total setup time) = tIS(base) + ∆tIS Setup (tIS) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of
V
REF(DC) and the first crossing of VIH(AC)min. Setup (tIS) nominal slew rate for a falling signal is defined as
the slew rate between the last crossing of VREF(DC) and the first crossing of VIL(AC)max. If the actual signal is always earlier than the nominal slew rate
line between shaded ’VREF(DC) to ac region’, use nominal slew rate for derating value (see Figure 23). If the actual signal is later than the nominal slew
rate line anywhere between shaded ’VREF(DC) to ac region’, the slew rate of a tangent line to the actual signal from the ac level to dc level is used for der-
ating value (see Figure 25).
Hold (tIH) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VIL(DC)max and the first crossing of VREF(DC).
Hold (tIH) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of VIH(DC)min and the first crossing of VREF(DC). If
the actual signal is always later than the nominal slew rate line between shaded ’dc to VREF(DC) region’, use nominal slew rate for derating value (see
Figure 24). If the actual signal is earlier than the nominal slew rate line anywhere between shaded ’dc to VREF(DC) region’, the slew rate of a tangent line
to the actual signal from the dc level to VREF(DC) level is used for derating value (see Figure 26).
For a valid transition the input signal has to remain above/below VIH/IL(AC) for some time tVAC (see Table 50).
Although for slow slew rates the total setup time might be negative (i.e. a valid input signal will not have reached VIH/IL(AC) at the time of the rising clock
transition) a valid input signal is still required to complete the transition and reach VIH/IL(AC).
For slew rates in between the values listed in Table 51, the derating values may obtained by linear interpolation.
These values are typically not subject to production test. They are verified by design and characterization.
[ Table 48 ] ADD/CMD Setup and Hold Base-Values for 1V/ns
[ps]
tIS(base)
DDR3-800
200
DDR3-1066
125
DDR3-1333
65
DDR3-1600
45
reference
VIH/L(AC)
VIH/L(DC)
VIH/L(AC)
tIH(base)
275
200
140
120
tIS(base)-AC150
200 + 150
125 + 150
65+125
45+125
Note : AC/DC referenced for 1V/ns DQ-slew rate and 2V/ns DQS slew rate
Note : The tIS(base)-AC150 specifications are further adjusted to add an additional 100ps of derating to accommodate for the lower alternate thresh-old
of 150mV and another 25ps to account for the earlier reference point [(175mv-150mV)/1 V/ns].
[ Table 49 ] Derating values DDR3-800/1066/1333/1600 tIS/tIH-AC/DC based
∆tIS, ∆tIH Derating [ps] AC/DC based
AC175 Threshold -> VIH(AC) = VREF(DC) + 175mV, VIL(AC) = VREF(DC) - 175mV
CLK,CLK Differential Slew Rate
4.0 V/ns
3.0 V/ns
2.0 V/ns
1.8 V/ns
1.6 V/ns
1.4V/ns
1.2V/ns
∆tIS
1.0V/ns
∆tIS
∆tIH
50
∆tIS
∆tIH
50
∆tIS
∆tIH
50
∆tIS
∆tIH
58
42
8
∆tIS
∆tIH
66
50
16
12
6
∆tIS
∆tIH
74
58
24
20
14
8
∆tIH
84
68
34
30
24
18
8
∆tIS
∆tIH
100
84
2.0
1.5
1.0
0.9
0.8
0.7
0.6
0.5
0.4
88
59
0
88
59
0
88
59
0
96
67
8
104
75
16
14
10
5
112
83
24
20
13
13
7
120
91
32
30
26
21
15
-2
128
99
40
38
34
29
23
5
34
34
34
0
0
0
50
CMD/
ADD
Slew
rate
-2
-4
-2
-4
-2
-4
6
4
46
-6
-10
-16
-26
-40
-60
-6
-10
-16
-26
-40
-60
-6
-10
-16
-26
-40
-60
2
-2
40
-11
-17
-35
-62
-11
-17
-35
-62
-11
-17
-35
-62
-3
-9
-27
-54
-8
0
34
V/ns
-18
-32
-52
-1
-10
-24
-44
-2
24
-19
-46
-11
-38
-16
-36
-6
10
-30
-26
-22
-10
Rev. 1.0 February 2009
Page 51 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
[ Table 50 ] Derating values DDR3-1333/1600 tIS/tIH-AC/DC based - Alternate AC150 Threshold
∆tIS, ∆tIH Derating [ps] AC/DC based
Alternate AC150 Threshold -> VIH(AC) = VREF(DC) + 150mV, VIL(AC) = VREF(DC) - 150mV
CLK,CLK Differential Slew Rate
4.0 V/ns
3.0 V/ns
2.0 V/ns
1.8 V/ns
1.6 V/ns
1.4V/ns
1.2V/ns
∆tIS
1.0V/ns
∆tIS
∆tIH
50
∆tIS
∆tIH
50
∆tIS
∆tIH
50
∆tIS
∆tIH
58
42
8
∆tIS
∆tIH
66
50
16
12
6
∆tIS
∆tIH
74
58
24
20
14
8
∆tIH
84
68
34
30
24
18
8
∆tIS
∆tIH
100
84
2.0
1.5
1.0
0.9
0.8
0.7
0.6
0.5
0.4
75
50
0
75
50
0
75
50
0
83
58
8
91
66
16
16
16
16
15
6
99
74
24
24
24
24
23
14
-1
107
82
32
32
32
32
31
22
7
115
90
40
40
40
40
39
30
15
34
34
34
0
0
0
50
CMD/
ADD
Slew
rate
0
-4
0
-4
0
-4
8
4
46
0
-10
-16
-26
-40
-60
0
-10
-16
-26
-40
-60
0
-10
-16
-26
-40
-60
8
-2
40
0
0
0
8
-8
0
34
V/ns
-1
-10
-25
-1
-10
-25
-1
-10
-25
7
-18
-32
-52
-10
-24
-44
-2
24
-2
-17
-16
-36
-6
10
-9
-26
-10
[ Table 51 ] Required time tVAC above VIH(AC) {blow VIL(AC)} for valid transition
tVAC @175mV [ps]
tVAC @150mV [ps]
Slew Rate[V/ns]
min
75
57
50
38
34
29
22
13
0
max
min
175
170
167
163
162
161
159
155
150
150
max
>2.0
2.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1.5
1.0
0.9
0.8
0.7
0.6
0.5
< 0.5
0
Rev. 1.0 February 2009
Page 52 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
Note :Clock and Strobe are drawn on a different time scale.
CK
tIH
tIH
tIS
tIS
CK
DQS
DQS
tDH
tDH
tDS
tDS
VDDQ
tVAC
VIH(AC) min
VREF to ac
region
VIH(DC) min
nominal
slew rate
VREF(DC)
nominal slew
rate
VIL(DC) max
VREF to ac
region
VIL(AC) max
VSS
tVAC
Delta TF
Delta TR
Setup Slew Rate
Rising Signal
V
IH(AC)min - VREF(DC)
Delta TR
V
REF(DC) - VIL(AC)max
Delta TF
Setup Slew Rate
=
=
Falling Signal
Figure 21 - Illustration of nominal slew rate and tVAC for setup time tDS (for DQ with respect to strobe) and tIS
(for ADD/CMD with respect to clock).
Rev. 1.0 February 2009
Page 53 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
Note :Clock and Strobe are drawn on a different time scale.
CK
tIH
tIH
tIS
tIS
CK
DQS
DQS
tDH
tDH
tDS
tDS
VDDQ
VIH(AC) min
VIH(DC) min
dc to VREF
region
nominal
slew rate
VREF(DC)
nominal
dc to VREF
region
dc to VREF
region
slew rate
VIL(DC) max
VIL(AC) max
VSS
Delta TF
Delta TR
Hold Slew Rate
Hold Slew Rate
Rising Signal
V
REF(DC) - VIL(DC)max
Delta TR
V
IH(DC)min - VREF(DC)
Delta TF
=
=
Falling Signal
Figure 22 - Illustration of nominal slew rate for hold time tDH (for DQ with respect to strobe) and tIH
(for ADD/CMD with respect to clock).
Rev. 1.0 February 2009
Page 54 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
Note :Clock and Strobe are drawn on a different time scale.
CK
tIH
tIH
tIS
tIS
CK
DQS
DQS
tDH
tDH
tDS
tDS
VDDQ
tVAC
nominal
line
VIH(AC) min
V
REF to ac
region
V
IH(DC) min
tangent
line
VREF(DC)
tangent
line
VIL(DC) max
VIL(AC) max
VREF to ac
region
nominal
line
Delta TR
VSS
tangent line[VIH(AC)min - VREF(DC)]
Delta TR
Setup Slew Rate
=
Rising Signal
Delta TF
Setup Slew Rate tangent line[VREF(DC) - VIL(AC)max]
=
Falling Signal
Delta TF
Figure 23. Illustration of tangent line for setup time tDS (for DQ with respect to strobe) and tIS
(for ADD/CMD with respect to clock)
Rev. 1.0 February 2009
Page 55 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
Note :Clock and Strobe are drawn on a different time scale.
CK
tIH
tIH
tIS
tIS
CK
DQS
DQS
tDH
tDH
tDS
tDS
VDDQ
VIH(AC) min
nominal
line
V
IH(DC) min
dc to VREF
region
tangent
line
VREF(DC)
tangent
line
dc to VREF
region
nominal
line
VIL(DC) max
VIL(AC) max
VSS
Delta TF
Delta TR
tangent line [ VREF(DC) - VIL(DC)max ]
Delta TR
Hold Slew Rate
=
Rising Signal
tangent line [ VIH(DC)min - VREF(DC) ]
Delta TF
Hold Slew Rate
=
Falling Signal
Figure 24 - Illustration of tangent line for hold time tDH (for DQ with respect to strobe) and tIH
(for ADD/CMD with respect to clock)
Rev. 1.0 February 2009
Page 56 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
14.4 Data Setup, Hold and Slew Rate Derating :
For all input signals the total tDS (setup time) and tDH (hold time) required is calculated by adding the data sheet tDS(base) and tDH(base) value (see
Table 52) to the ∆ tDS and ∆tDH (see Table 53) derating value respectively. Example: tDS (total setup time) = tDS(base) + ∆tDS.
Setup (tDS) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VREF(DC) and the first crossing of VIH(AC)min.
Setup (tDS) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of VREF(DC) and the first crossing of VIL(AC)max
(see Figure 25). If the actual signal is always earlier than the nominal slew rate line between shaded ’VREF(DC) to ac region’, use nominal slew rate for
derating value. If the actual signal is later than the nominal slew rate line anywhere
between shaded ’VREF(DC) to ac region’, the slew rate of a tangent line to the actual signal from the ac level to dc level is used for derating value (see
Figure 27).
Hold (tDH) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VIL(DC)max and the first crossing of VREF(DC).
Hold (tDH) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of VIH(DC)min and the first crossing of VREF(DC)
(see Figure 26). If the actual signal is always later than the nominal slew rate line between shaded ’dc level to VREF(DC) region’, use nominal slew rate
for derating value. If the actual signal is earlier than the nominal slew rate line anywhere between shaded ’dc to VREF(DC) region’, the slew rate of a tan-
gent line to the actual signal from the dc level to VREF(DC) level is used for derating value (see Figure 28).
For a valid transition the input signal has to remain above/below VIH/IL(AC) for some time tVAC (see Table 54).
Although for slow slew rates the total setup time might be negative (i.e. a valid input signal will not have reached VIH/IL(AC) at the time of the rising clock
transition) a valid input signal is still required to complete the transition and reach VIH/IL(AC).
For slew rates in between the values listed in the tables the derating values may obtained by linear interpolation.
These values are typically not subject to production test. They are verified by design and characterization.
[ Table 52 ] Data Setup and Hold Base-Value
[ps]
DDR3-800
DDR3-1066
DDR3-1333
DDR3-1600
reference
VIH/L(AC)
VIH/L(DC)
tDS(base)
tDH(base)
75
25
30
65
10
45
150
100
Note : AC/DC referenced for 1V/ns DQ-slew rate and 2 V/ns DQS slew rate)
[ Table 53 ] Derating values DDR3-800/1066/1333/1600 tIS/tIH-AC/DC based
∆tDS, ∆tDH Derating [ps] AC/DC baseda
DQS,DQS Differential Slew Rate
4.0 V/ns
3.0 V/ns
2.0 V/ns
1.8 V/ns
1.6 V/ns
1.4V/ns
1.2V/ns
1.0V/ns
∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH
2.0
1.5
1.0
0.9
0.8
0.7
0.6
0.5
0.4
2.0
1.5
1.0
0.9
0.8
0.7
0.6
0.5
0.4
88
59
0
-
50
34
0
-
88
59
0
-2
-
50
34
0
-4
-
88
59
0
50
34
0
-
67
8
6
2
-3
-
-
42
8
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
16
14
10
5
16
12
6
-
-
-
-
DDR3 DQ
-2
-6
-
-4
-10
-
4
22
18
13
7
20
14
8
-
-
-
-
-
-
-
Slew
-
-
-2
-8
-
26
21
15
-2
-30
-
24
18
8
800/ rate
1066 V/ns
-
-
-
-
0
29
23
6
34
24
10
-10
-
-
-
-
-
-
-
-1
-
-10
-
-2
-16
-
-
-
-
-
-
-
-
-
-11
-
-6
-26
-
-
-
-
-
-
-
-
-
-
-
-
-22
-
75
50
0
-
50
34
0
-
75
50
0
0
-
50
34
0
-4
-
75
50
0
50
34
0
-
-
-
-
-
58
8
8
8
8
-
42
8
-
-
-
-
-
-
-
-
16
16
16
16
15
-
16
12
6
-
-
-
-
-
-
-
DDR3 DQ
0
-4
-10
-
4
24
24
24
23
14
-
20
14
8
-2
-16
-
-
-
-
-
Slew
-
-
0
-2
-8
-
32
32
31
22
7
24
18
8
-6
-26
-
-
1333/ rate
1600 V/ns
-
-
-
-
-
0
40
39
30
15
34
24
10
-10
-
-
-
-
-
-
-10
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Note : a. Cell contents shaded in red are defined as ’not supported’.
[ Table 54 ] Required time tVAC above VIH(AC) {blow VIL(AC)} for valid transition
tVAC[ps] DDR3-800/1066
Slew Rate[V/ns]
tVAC[ps] DDR3-1333/1600
min max
min
75
57
50
38
34
29
22
13
0
max
>2.0
2.0
1.5
1.0
0.9
0.8
0.7
0.6
0.5
<0.5
-
-
-
-
-
-
-
-
-
-
175
170
167
163
162
161
159
155
155
150
-
-
-
-
-
-
-
-
-
-
0
Rev. 1.0 February 2009
Page 57 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
Note :Clock and Strobe are drawn on a different time scale.
CK
tIH
tIH
tIS
tIS
CK
DQS
DQS
tDH
tDH
tDS
tDS
VDDQ
tVAC
VIH(AC) min
VREF to ac
region
VIH(DC) min
nominal
slew rate
VREF(DC)
nominal slew
rate
VIL(DC) max
VREF to ac
region
VIL(AC) max
VSS
tVAC
Delta TF
Delta TR
Setup Slew Rate VIH(AC)min - VREF(DC)
V
REF(DC) - VIL(AC)max
Delta TF
Setup Slew Rate
=
=
Rising Signal
Delta TR
Falling Signal
Figure 25 - Illustration of nominal slew rate and tVAC for setup time tDS (for DQ with respect to strobe) and tIS
(for ADD/CMD with respect to clock).
Rev. 1.0 February 2009
Page 58 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
Note :Clock and Strobe are drawn on a different time scale.
CK
tIH
tIH
tIS
tIS
CK
DQS
DQS
tDH
tDH
tDS
tDS
VDDQ
VIH(AC) min
V
IH(DC) min
dc to VREF
region
nominal
slew rate
VREF(DC)
nominal
dc to VREF
region
dc to VREF
region
slew rate
VIL(DC) max
VIL(AC) max
VSS
Delta TF
Delta TR
V
REF(DC) - VIL(DC)max
Delta TR
VIH(DC)min - VREF(DC)
Delta TF
Hold Slew Rate
Rising Signal
Hold Slew Rate
Falling Signal
=
=
Figure 26 - Illustration of nominal slew rate for hold time tDH (for DQ with respect to strobe) and tIH
(for ADD/CMD with respect to clock).
Rev. 1.0 February 2009
Page 59 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
Note :Clock and Strobe are drawn on a different time scale.
CK
tIH
tIH
tIS
tIS
CK
DQS
DQS
tDH
tDH
tDS
tDS
VDDQ
tVAC
nominal
line
VIH(AC) min
V
REF to ac
region
V
IH(DC) min
tangent
line
VREF(DC)
tangent
line
VIL(DC) max
VIL(AC) max
VREF to ac
region
nominal
line
Delta TR
VSS
tangent line[VIH(AC)min - VREF(DC)]
Delta TR
Setup Slew Rate
=
Rising Signal
Delta TF
tangent line[VREF(DC) - VIL(AC)max]
Delta TF
Setup Slew Rate
=
Falling Signal
Figure 27 - Illustration of tangent line for setup time tDS (for DQ with respect to strobe) and tIS
(for ADD/CMD with respect to clock)
Rev. 1.0 February 2009
Page 60 of 61
1Gb DDR3 SDRAM
K4B1G04(08/16)46E
Note :Clock and Strobe are drawn on a different time scale.
CK
tIH
tIH
tIS
tIS
CK
DQS
DQS
tDH
tDH
tDS
tDS
VDDQ
VIH(AC) min
nominal
line
V
IH(DC) min
dc to VREF
region
tangent
line
VREF(DC)
tangent
line
dc to VREF
region
nominal
line
VIL(DC) max
VIL(AC) max
VSS
Delta TF
Delta TR
tangent line [ VREF(DC) - VIL(DC)max ]
Delta TR
Hold Slew Rate
=
Rising Signal
tangent line [ VIH(DC)min - VREF(DC) ]
Delta TF
Hold Slew Rate
=
Falling Signal
Figure 28 - Illustration of tangent line for hold time tDH (for DQ with respect to strobe) and tIH
(for ADD/CMD with respect to clock)
Rev. 1.0 February 2009
Page 61 of 61
相关型号:
K4B1G1646G-BCH90
DDR DRAM, 64MX16, 0.255ns, CMOS, PBGA96, HALOGEN FREE AND ROHS COMPLIANT, FBGA-96
SAMSUNG
©2020 ICPDF网 联系我们和版权申明