SML-P12UTT87Q [ROHM]
Single Color LED, Red, Colorless Transparent, 0.6mm, 1 X 0.60 MM, 0.20 MM HEIGHT, ROHS COMPLIANT, ULTRA COMPACT, MINIMOLD, THIN, 2 PIN;
| 型号： | SML-P12UTT87Q |
| 厂家： | 
ROHM |
| 描述： | Single Color LED, Red, Colorless Transparent, 0.6mm, 1 X 0.60 MM, 0.20 MM HEIGHT, ROHS COMPLIANT, ULTRA COMPACT, MINIMOLD, THIN, 2 PIN 光电 |
| 文件： | 总9页 (文件大小：638K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SML-P1 series
PICOLEDTM
Datasheet
lFeatures
lOutline
• Ultra compact, thin sizeꢀ1.0×0.6mm
• Original device technology enables high brightness and high reliability
• Lead Free/RoHS Compliant.
lSize
Color
V
P
U
E
D
B
Y
Type
1006 (0402)
1.0×0.6mm (t=0.2mm)
M
WB
lDimensions
lRecommended Solder Pattern
Tolerance : ±0.05
(unit : mm)
(unit : mm)
lSpecifications
Absolute Maximum Ratings (Ta=25ºC)
Electrical and Optical Characteristics (Ta=25ºC)
Emitting
Color
Peak Forward
Power
Forward Voltag VF Reverse Current IR
Luminous Intensity IV
Forward
Reverse
Current
Voltage
Dominant Wavelength lD
IF
(V) (mA) (mA) (V) (nm) (nm) (nm) (mA) (mcd) (mcd) (mA)
Chip
Structure
Operating Temp.
Topr(ºC)
Part No.
Storage Temp.
Tstg(ºC)
Min.*2
Max.*2
Dissipation
Current
IF
VR
IF
Typ.
Max.
Typ.
Min. Typ.
PD(mW) IF(mA) IFP(mA) VR(V)
SML-P12VT(R)
SML-P12UT(R)
SML-P12DT(R)
SML-P12YT(R)
SML-P12MT(R)
SML-P12PT(R)
SMLP13EC8T
SMLP13BC8T
SCMP13WBC8W
625 630 635
615 620 625
602 605 608
587 590 593
569 572 575
557 560 563
520 527 535
465 470 475
(x, y) (0.30, 0.30)
60
85
Red
50
2.0
25
Orange
Yellow
100
130
35
AIGaInP
on GaAs
100*1
52
20
2.1 20
4
20
40
10
20
Yellowish
Green
5
100
-40 to +85 -40 to +100
54
34
33
2.2
3.0
Green
4.0 13
56 (110)
9.0 (25)
90 150
Bluish
Green
50*1
InGaN Blue
White
10
5
5
5
5
2.9
*1 : Duty 1/10, 1kHz *2 : Reference
*PICOLEDTM is ROHM's pending trademark.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.05 - Rev.D
1/8
Data Sheet
SML-P1 series
lElectrical Characteristics Curves
Fig.2 Luminous Intensity -
Fig.1 Forward Current - Forward Voltages
Atmosphere Temperature
SML-P12VT(R)
Ta=25ºC
IF=20mA
SML-P12UT(R)
SML-P12DT(R)
SML-P12YT(R)
SML-P12MT(R)
SML-P12PT(R)
SML-P12VT(R)
SML-P12UT(R)
SML-P12DT(R)
SML-P12YT(R)
SML-P12MT(R)
SML-P12PT(R)
ꢀ
FORWARD VOLTAGE : VF [V]
ATMOSPHERE TEMPERATURE : Ta [ºC]
Fig.3 Luminous Intensity - Forward Current
Fig.4 Derating
SML-P12VT(R)
Ta=25ºC
SML-P12UT(R)
SML-P12DT(R)
SML-P12YT(R)
SML-P12MT(R)
SML-P12PT(R)
SML-P12VT(R)
SML-P12UT(R)
SML-P12DT(R)
SML-P12YT(R)
SML-P12MT(R)
SML-P12PT(R)
FORWARD CURRENT : IF [mA]
AMBIENT TEMPERATURE : Ta [ºC]
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.05 - Rev.D
2/8
Data Sheet
SML-P1 series
lElectrical Characteristics Curves
Fig.2 Luminous Intensity -
Fig.1 Forward Current - Forward Voltages
Atmosphere Temperature
Ta=25ºC
IF=20mA
SMLP13EC8T
SMLP13BC8T
SCMP13WBC8W
ꢀ
SMLP13EC8T
SMLP13BC8T
SCMP13WBC8W
FORWARD VOLTAGE : VF [V]
ATMOSPHERE TEMPERATURE : Ta [ºC]
Fig.3 Luminous Intensity - Forward Current
Fig.4 Derating
SMLP13EC8T
SMLP13BC8T
SCMP13WBC8W
Ta=25ºC
SMLP13EC8T
SMLP13BC8T
SCMP13WBC8W
FORWARD CURRENT : IF [mA]
AMBIENT TEMPERATURE : Ta [ºC]
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.05 - Rev.D
3/8
Data Sheet
SML-P1 series
lSpectrum Data
SML-P12VT(R)
SML-P12UT(R)
SML-P12DT(R)
SML-P12YT(R)
SML-P12MT(R)
SML-P12PT(R)
IF=5mA
IF=20mA
1.0
0.8
0.6
0.4
0.2
0.0
1
0.8
0.6
0.4
0.2
SMLP13BC8T
SCMP13WBC8W
ꢀ
0
380
480
580
680
780
380
480
580
680
780
WAVELENGTH [nm]
WAVELENGTH [nm]
* Please take this data as a reference data for the samples are measured randomly.
* The data is relativized for each color. It is NOT to show the spectrum peaks are equal.
lViewing Angle
SML-P12VT(R)
SML-P12UT(R)
SML-P12DT(R)
SML-P12YT(R)
SML-P12MT(R)
SML-P12PT(R)
SCANNING ANGLE (deg)
SCANNING ANGLE (deg)
RELATIVE INTENSITY
RELATIVE INTENSITY
SMLP13EC8T
SMLP13BC8T
SCMP13WBC8W
SCANNING ANGLE (deg)
SCANNING ANGLE (deg)
RELATIVE INTENSITY
RELATIVE INTENSITY
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.05 - Rev.D
4/8
Data Sheet
SML-P1 series
lRank Reference of Brightness
Red(V,U)
(Ta=25ºC, IF＝20mA)
Rank
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
W
X
1000 to 1600
100 to 160 160 to 250 250 to 400 400 to 630 630 to 1000
Iv (mcd)
1.0 to 1.6 1.6 to 2.5 2.5 to 4.0 4.0 to 6.3 6.3 to 10 10 to 16 16 to 25 25 to 40 40 to 63 63 to 100
SML-P12VT
SML-P12UT
Orange(D)
(Ta=25ºC, IF＝20mA)
Rank
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
W
X
1000 to 1600
100 to 160 160 to 250 250 to 400 400 to 630 630 to 1000
Iv (mcd)
1.0 to 1.6 1.6 to 2.5 2.5 to 4.0 4.0 to 6.3 6.3 to 10 10 to 16 16 to 25 25 to 40 40 to 63 63 to 100
SML-P12DT
Yellow(Y)
(Ta=25ºC, IF＝20mA)
Rank
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
W
X
1000 to 1600
Iv (mcd)
100 to 160 160 to 250 250 to 400 400 to 630 630 to 1000
1.0 to 1.6 1.6 to 2.5 2.5 to 4.0 4.0 to 6.3 6.3 to 10 10 to 16 16 to 25 25 to 40 40 to 63 63 to 100
SML-P12YT
Green(M,P)
(Ta=25ºC, IF＝20mA)
Rank
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
W
X
1000 to 1600
Iv (mcd)
100 to 160 160 to 250 250 to 400 400 to 630 630 to 1000
1.0 to 1.6 1.6 to 2.5 2.5 to 4.0 4.0 to 6.3 6.3 to 10 10 to 16 16 to 25 25 to 40 40 to 63 63 to 100
SML-P12MT
SML-P12PT
Bluish Green(E)
(Ta=25ºC, IF＝5mA)
Rank
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
W
Iv (mcd)
140 to 220 220 to 360 360 to 560 560 to 900
0.9 to 1.4 1.4 to 2.2 2.2 to 3.6 3.6 to 5.6 5.6 to 9.0 9 to 14 14 to 22 22 to 36 36 to 56 56 to 90 90 to 140
SMLP13EC8T
Blue(B)
(Ta=25ºC, IF＝5mA)
Rank
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
W
Iv (mcd)
140 to 220 220 to 360 360 to 560 560 to 900
0.9 to 1.4 1.4 to 2.2 2.2 to 3.6 3.6 to 5.6 5.6 to 9.0 9 to 14 14 to 22 22 to 36 36 to 56 56 to 90 90 to 140
SMLP13BC8T
White(WB)
(Ta=25ºC, IF＝5mA)
Rank
N
P
Q
R
S
T
U
V
W
Iv (mcd)
140 to 220 220 to 360 360 to 560 560 to 900
14 to 22 22 to 36 36 to 56 56 to 90 90 to 140
SCMP13WBC8W
lChromaticity Diagram
K
F
[Chromaticity Coordimates]
(Ta=25ºC, IF＝5mA)
H
A
F
H
K
A
x
y
x
y
x
y
x
y
0.28 0.248 0.283 0.305 0.287 0.295 0.304 0.33
0.296 0.276 0.304 0.33 0.307 0.315 0.33 0.36
0.283 0.305 0.307 0.315 0.311 0.294 0.33 0.318
0.264 0.267 0.287 0.295 0.296 0.276 0.311 0.294
Measurement tolerance : 0.02
CIE x
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.05 - Rev.D
5/8
Data Sheet
SML-P1 series
±0.1
4.00
+0.1
0
lTaping
φ1.5
A
±0.05
2.00
±0.05
0.70
+0.05
-0.03
0.28
Enlarged drawing of ‟A”
±1
11.4
(unit : mm)
Packaging quantity
Pulling
Direction
(Note) Tolerance is 0.1mm, unless otherwise specified.
lPart No. Construction
lPacking Specification
ROHM LED products are being shipped with desiccant (silica gel) concluded in moisture-proof bags.
Pasting the moisture sensitive label on the outer surface of the moisture-proof bags or enclosing the humidity indication card
inside the bag is available upon request.
Please contact the nearest sales office or distributer if necessary.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.05 - Rev.D
6/8
Data Sheet
SML-P1 series
lAttention Points In Handling
This product was developed as a surface mount LED especially suitable for reflow soldering.
Please take care of following points when using this device.
1.DESIGNING OF PCB
As for a recommendable solder pattern, Please refer to Fig ”Recommended Solder Pattern”.
The size and direction of the pad pattern depend on the condition of the PCB.
Reference
This product of structured with rear/bottom electrode to be soldered.
The formation of solder fillet is not guaranteed due to its electrode shape
Mask open area ratio：80%
Mask thickness ：80 to 100mm
Additional notification of mounting :
We recommend additional facility of mounting Machine due to small size package
which might be haven electrification, and product might be moved in the taping pocket.
And the mounting production efficiency will be decreased.
Ex) Magnet facility etc.
2.SOLDERING (Sn-Cu, Sn-Ag-Cu, Sn-Ag-Bi-Cu)
LED products do not contain reinforcement
materials such as glass fillers.
300
Max.260ºC, Within
230 to 260ºC
Therefore, thermal stress by soldering greatly
250
140 to 180ºC
200
150
100
50
influences its reliability.
The temperature conditions for reflow soldering
should therefore be set up according to the
characteristic of this product. (See Fig-1)
Number of reflow process shall be max 2 times
and these processes shall be performed in a row.
Cooling process to normal temperature shall be required
between the first and the second soldering process.
Min.1 min
Max.
0
(Fig-1)
SOLDERING
IRON
(Fig-2)
SOLDERING OPERATION
1) SOLDER USED
Sn-Cu, Sn-Ag-Cu, Sn-Ag-Bi-Cu
2) SOLDERING CONDITION
LED products do not contain reinforcement material such as a glass fillers.
So thermal stress by soldering greatly influence its reliability.
Please keep following points for manual soldering.
SOLDERING
LAND
ITEM
RECOMMENDED CONDITION
Less than 30W, top of iron less than 3mm.
Condition) Temp. of iron top less than
400ºC within 3 sec.
Soldering iron
a)
b)
Heating method
Heating on PCB pattern, not direct to the LED. (Fig-2)
Please handle after the part temp.
c)
Handling after soldering
Goes down to room temp.
3.HANDLING AFTER MOUNTING (Fig.-3)
As shown in the drawing on the right, in case outside force of about 700g is given to the device, stress is concentrated
to the jointed part between mold resin and substrate.
Therefore there is a possibility to breath the device or PCB.
Careful handing is needed as ROHM cannot guarantee the falling of the device by outside force after mounting.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.05 - Rev.D
7/8
Data Sheet
SML-P1 series
4.WASHING
Please note the following points when washing is required after soldering.
4-1) WASHING SOLVENT
Isopropyl alcohol or other alcohol solvent is recommendable.
4-2) TEMPERATURE
Below 30ºC, immersion time ; within 3 minutes.
4-3) ULTRA SONIC WASHING
Below 15W/1 litter of solvent tub or less.
4-4) COOLING
Below 100ºC within 3 minutes.
5.EROSION GAS
Utilization in erosion gas atmosphere may degenerate the plating surface which might cause deterioration of
solder strength, optical characteristics, or functions.
Please take precautions against occurrence of gas from the surrounding parts on the occasion of custody,
and also after mounted on circuit board.
6.STORAGE
At reflow soldering, the reliability of this product is often influenced by moisture
absorption so we apply the packaging with moisture proof for better condition is use, please also note that
6-1) Not to be opened before using.
6-2) To be kept in our moisture proof packaging with some desiccant (SILICA GEL) after opening it.
To be baked in case the SILICA GEL indicator its color from either blue to clear or green to pink.
6-3) Please use within 168 hours after the package was opened. (Condition at 30ºC, max.70%Rh.)
In case it is not used within 168 hours, please put it back into our packaging.
6-4) BAKING
Please bake under reel condition at 60ºC, 1 to 224 hours (max.20%Rh) after un-sealing.
While baking is done, the reel and emboss tape may be easily deformed.
Please be careful not to give any stress.
7.LIFE TIME
Blue led die used in this product will cause reduction of luminous intensity due to epoxy resin discoloration
depending on the using conditions and environmental.
Please inquire our sales contact if long life time is required on your application.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.05 - Rev.D
8/8
Notice
N o t e s
1) The information contained herein is subject to change without notice.
2) Before you use our Products, please contact our sales representative and verify the latest specifica-
tions :
3) Although ROHM is continuously working to improve product reliability and quality, semicon-
ductors can break down and malfunction due to various factors.
Therefore, in order to prevent personal injury or fire arising from failure, please take safety
measures such as complying with the derating characteristics, implementing redundant and
fire prevention designs, and utilizing backups and fail-safe procedures. ROHM shall have no
responsibility for any damages arising out of the use of our Poducts beyond the rating specified by
ROHM.
4) Examples of application circuits, circuit constants and any other information contained herein are
provided only to illustrate the standard usage and operations of the Products. The peripheral
conditions must be taken into account when designing circuits for mass production.
5) The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly,
any license to use or exercise intellectual property or other rights held by ROHM or any other
parties. ROHM shall have no responsibility whatsoever for any dispute arising out of the use of
such technical information.
6) The Products are intended for use in general electronic equipment (i.e. AV/OA devices, communi-
cation, consumer systems, gaming/entertainment sets) as well as the applications indicated in
this document.
7) The Products specified in this document are not designed to be radiation tolerant.
8) For use of our Products in applications requiring a high degree of reliability (as exemplified
below), please contact and consult with a ROHM representative : transportation equipment (i.e.
cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety
equipment, medical systems, servers, solar cells, and power transmission systems.
9) Do not use our Products in applications requiring extremely high reliability, such as aerospace
equipment, nuclear power control systems, and submarine repeaters.
10) ROHM shall have no responsibility for any damages or injury arising from non-compliance with
the recommended usage conditions and specifications contained herein.
11) ROHM has used reasonable care to ensur the accuracy of the information contained in this
document. However, ROHM does not warrants that such information is error-free, and ROHM
shall have no responsibility for any damages arising from any inaccuracy or misprint of such
information.
12) Please use the Products in accordance with any applicable environmental laws and regulations,
such as the RoHS Directive. For more details, including RoHS compatibility, please contact a
ROHM sales office. ROHM shall have no responsibility for any damages or losses resulting
non-compliance with any applicable laws or regulations.
13) When providing our Products and technologies contained in this document to other countries,
you must abide by the procedures and provisions stipulated in all applicable export laws and
regulations, including without limitation the US Export Administration Regulations and the Foreign
Exchange and Foreign Trade Act.
14) This document, in part or in whole, may not be reprinted or reproduced without prior consent of
ROHM.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
R1102
A
相关型号：
SML-P12UTT87R
Single Color LED, Red, Colorless Transparent, 0.6mm, 1 X 0.60 MM, 0.20 MM HEIGHT, ROHS COMPLIANT, ULTRA COMPACT, MINIMOLD, THIN, 2 PIN
ROHM
SML-P12UTT87S
Single Color LED, Red, Colorless Transparent, 0.6mm, 1 X 0.60 MM, 0.20 MM HEIGHT, ROHS COMPLIANT, ULTRA COMPACT, MINIMOLD, THIN, 2 PIN
ROHM
SML-P12VT(R)
ROHM的PICOLED™ － 有效利用其超小型、超薄型规格尺寸的优点，可以构成此前无法想象的超精细矩阵，使其表现能力发挥得淋漓尽致！而且，是今后整机小型化、薄型化必不可少的主要角色！
ROHM
SML-P12VTT86P
Single Color LED, Red, Colorless Transparent, 0.6mm, 1 X 0.60 MM, 0.20 MM HEIGHT, ROHS COMPLIANT, ULTRA COMPACT, MINIMOLD, THIN, 2 PIN
ROHM
SML-P12VTT86Q
Single Color LED, Red, Colorless Transparent, 0.6mm, 1 X 0.60 MM, 0.20 MM HEIGHT, ROHS COMPLIANT, ULTRA COMPACT, MINIMOLD, THIN, 2 PIN
ROHM
SML-P12VTT86R
Single Color LED, Red, Colorless Transparent, 0.6mm, 1 X 0.60 MM, 0.20 MM HEIGHT, ROHS COMPLIANT, ULTRA COMPACT, MINIMOLD, THIN, 2 PIN
ROHM
©2020 ICPDF网 联系我们和版权申明