LM2904FV [ROHM]
Ground Sense Operational Amplifiers;型号: | LM2904FV |
厂家: | ROHM |
描述: | Ground Sense Operational Amplifiers |
文件: | 总48页 (文件大小:1413K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Datasheet
Operational Amplifiers
Ground Sense Operational Amplifiers
LM358xxx LM324xxx LM2904xxx LM2902xxx
General Description
Key Specifications
LM358xxx and LM2904xxx series are dual ground
sense operational amplifiers. LM324xxx and
LM2902xxx series are quad. These have features of
low current consumption and wide operating voltage
range from 3V to 32V (single power supply).
Operating Supply Voltage (Single Supply):
3.0V to 32.0V
Operating Temperature Range:
LM358xxx:
LM324xxx:
LM2904xxx:
LM2902xxx:
-40°C to +85°C
-40°C to +85°C
-40°C to +125°C
-40°C to +125°C
4.5mV (Max)
Features
Input Offset Voltage:
Input Bias Current:
Operable with a Single Power Supply
Wide Operating Supply Voltage Range
Input/output Ground Sense
High Large Signal Voltage Gain
20nA (Typ)
Packages
SOP8
W(Typ) x D(Typ) x H(Max)
5.00mm x 6.20mm x 1.71mm
4.90mm x 6.00mm x 1.65mm
3.00mm x 6.40mm x 1.35mm
3.00mm x 6.40mm x 1.20mm
3.00mm x 4.90mm x 1.10mm
2.90mm x 4.00mm x 0.90mm
8.70mm x 6.20mm x 1.71mm
8.65mm x 6.00mm x 1.65mm
5.00mm x 6.40mm x 1.35mm
5.00mm x 6.40mm x 1.20mm
Applications
SOP-J8
Current Sense Application
Buffer Application Amplifier
Active Filter
SSOP-B8
TSSOP-B8
TSSOP-B8J
MSOP8
Consumer Electronics
SOP14
SOP-J14
SSOP-B14
TSSOP-B14J
Pin Configuration
LM358F, LM2904F
LM358FJ, LM2904FJ
LM358FV, LM2904FV
: SOP8
: SOP-J8
: SSOP-B8
LM358FVT, LM2904FVT : TSSOP-B8
LM358FVJ, LM2904FVJ : TSSOP-B8J
LM358FVM, LM2904FVM : MSOP8
Pin No.
Pin Name
1
2
3
4
5
6
7
8
OUT1
-IN1
1
2
3
4
8
7
6
5
OUT1
VCC
OUT2
-IN2
+IN1
VEE
+IN2
-IN2
CH1
-IN1
-
+
CH2
+IN1
-
+
+IN2
VEE
OUT2
VCC
○Product structure:Silicon monolithic integrated circuit ○This product has no designed protection against radioactive rays.
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・14・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
1/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
LM324F, LM2902F
LM324FJ, LM2902FJ
LM324FV, LM2902FV
: SOP14
: SOP-J14
: SSOP-B14
LM324FVJ, LM2902FVJ : TSSOP-B14J
Pin No.
Pin Name
OUT1
-IN1
1
2
OUT1
1
2
3
4
5
6
7
14
13
12
11
OUT4
-IN4
3
+IN1
VCC
-IN1
+IN1
VCC
+IN2
-IN2
CH1
CH4
4
-
-
+
+
+IN4
VEE
5
+IN2
-IN2
6
7
OUT2
OUT3
-IN3
10 +IN3
8
-
-
+
+
CH2
CH3
9
9
8
-IN3
10
11
12
13
14
+IN3
VEE
OUT2
OUT3
+IN4
-IN4
OUT4
Absolute Maximum Ratings (TA=25°C)
Parameter
Rating
Symbol
Unit
LM358xxx
LM324xxx LM2904xxx LM2902xxx
Supply Voltage
VCC-VEE
36
V
0.68(Note 1,9)
-
0.68(Note 1,9)
SOP8
-
0.67(Note 2,9)
0.62(Note 3,9)
-
0.67(Note 2,9)
0.62(Note 3,9)
-
SOP-J8
SSOP-B8
-
-
0.62(Note 3,9)
0.58(Note 4,9)
0.58(Note 4,9)
-
0.62(Note 3,9)
0.58(Note 4,9)
0.58(Note 4,9)
-
TSSOP-B8
TSSOP-B8J
MSOP8
SOP14
SOP-J14
SSOP-B14
TSSOP-B14J
VID
-
-
Power Dissipation
PD
W
-
-
-
-
-
-
0.56(Note 5,9)
1.02(Note 6,9)
0.87(Note 7,9)
0.85(Note 8,9)
-
-
-
-
0.56(Note 5,9)
1.02 (Note 6,9)
0.87(Note 7,9)
0.85(Note 8,9)
Differential Input Voltage (Note 10)
Input Common-mode Voltage Range
Input Current(Note 11)
36
V
V
VICM
(VEE-0.3) to (VEE+36)
±10
II
mA
Vopr
Operating Supply Voltage
3.0 to 32.0
V
Operating Temperature Range
Storage Temperature Range
Maximum Junction Temperature
Topr
-40 to +85
-40 to +125
°C
°C
°C
Tstg
-55 to +150
150
Tjmax
(Note 1) Reduce by 5.5mW per 1°C above 25C.
(Note 2) Reduce by 5.4mW per 1°C above 25°C.
(Note 3) Reduce by 5.0mW per 1°C above 25°C.
(Note 4) Reduce by 4.7mW per 1°C above 25°C.
(Note 5) Reduce by 4.5mW per 1°C above 25°C.
(Note 6) Reduce by 8.2mW per 1°C above 25°C.
(Note 7) Reduce by 7.0mW per 1°C above 25°C.
(Note 8) Reduce by 6.8mW per 1°C above 25°C.
(Note 9) Mounted on an FR4 glass epoxy PCB 70mm×70mm×1.6mm (Copper foil area less than 3%).
(Note 10) Differential Input Voltage is the voltage difference between the inverting and non-inverting inputs.
The input pin voltage is set to more than VEE
.
(Note 11) An excessive input current will flow when input voltages of less than VEE-0.6V are applied.
The input current can be set to less than the rated current by adding a limiting resistor.
Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is
operated over the absolute maximum ratings.
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
2/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Electrical Characteristics
○LM358xxx, LM2904xxx (Unless otherwise specified VCC=+5V, VEE=0V)
Limits
Temperature
Parameter
Symbol
Unit
mV
Condition
Range
Min
Typ
Max
4.5
5
25°C
-
-
1
-
VOUT=1.4V
VCC=5 to 30V, VOUT=1.4V
Input Offset Voltage(Note 12,13)
Input Offset Voltage Drift(Note 12)
Input Offset Current(Note 12,13)
VIO
∆VIO/∆T
IIO
Full Range
-
-
6
-
μV/°C VOUT=1.4V
25°C
Full Range
25°C
-
-
2
-
50
200
250
300
1.2
1.5
-
nA
nA
V
OUT=1.4V
OUT=1.4V
-
20
-
Input Bias Current(Note 12,13)
Supply Current(Note 13)
IB
V
Full Range
25°C
-
-
0.6
-
ICC
mA RL=∞, All Op-Amps
Full Range
25°C
-
3.5
27
-
-
RL=2kΩ
Maximum Output Voltage (High)(Note 13)
Maximum Output Voltage (Low)(Note 13)
Large Signal Voltage Gain
VOH
VOL
AV
V
Full Range
Full Range
28
5
-
VCC=30V, RL=10kΩ
20
-
mV RL=∞
25
88
0
100
100
-
V/mV
RL≧2kΩ, VCC=15V
25°C
25°C
VOUT=1.4 to 11.4V
dB
-
VICM=VEE to (VCC-1.5V)
VOUT=1.4V
Input Common-mode Voltage Range
VICM
3.5
V
Input Common-mode Voltage Range
(VEE side) (Note 14)
VICM
Full Range
25°C
-
0.1
80
100
30
-
-
-
-
-
-
-
-
-
-
-
V
VOUT=1.4V
Common-mode Rejection Ratio
Power Supply Rejection Ratio
CMRR
PSRR
70
65
20
10
20
5
dB VOUT=1.4V
25°C
dB VCC=5 to 30V
25°C
V
+IN=1V, V-IN=0V
Output Source Current(Note 13,15)
ISOURCE
mA
VOUT=0V, Short Current
Full Range
25°C
27
-
V+IN=0V, V-IN=1V
mA
VOUT=5V, Short Current
Output Sink Current(Note 13,15)
ISINK
Full Range
25°C
V+IN=0V, V-IN=1V
VOUT=200mV
20
-
50
120
0.3
μA
Channel Separation
Slew Rate
CS
SR
GBW
θ
25°C
dB f=1kHz, Input Referred
VCC=15V, Av=0dB
V/μs
25°C
-
RL=2kΩ, CL=100pF
VCC=15V, VEE=-15V
RL=2kΩ, CL=100pF
Gain Bandwidth
Phase Margin
25°C
25°C
25°C
-
-
-
0.8
80
40
-
-
-
MHz
deg Av=40dB
VCC=15V, VEE=-15V
RS=100Ω, VIN=0V, f=1kHz
Input Referred Noise Voltage
VN
nV/ Hz
(Note 12) Absolute value
(Note 13) LM358xxx Full Range: TA=-40C to +85C, LM2904xxx Full Range: TA=-40C to +125C
(Note 14) LM2904xxx only.
(Note 15) Consider the power dissipation of the IC under high temperature when selecting the output current value.
There may be a case where the output current value is reduced due to the rise in IC temperature caused by the heat generated inside the IC.
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
3/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Electrical Characteristics - continued
○LM324xxx, LM2902xxx (Unless otherwise specified VCC=+5V, VEE=0V)
Limits
Temperature
Parameter
Symbol
Unit
mV
Condition
Range
Min
Typ
Max
4.5
5
25°C
-
-
1
-
VOUT=1.4V
VCC=5 to 30V, VOUT=1.4V
Input Offset Voltage(Note 16,17)
Input Offset Voltage Drift(Note 17)
Input Offset Current(Note 16,17)
VIO
∆VIO/∆T
IIO
Full Range
-
-
6
-
μV/°C VOUT=1.4V
25°C
Full Range
25°C
-
-
2
-
50
200
250
300
2
nA
nA
V
V
OUT=1.4V
OUT=1.4V
-
20
-
Input Bias Current(Note 16,17)
Supply Current(Note 17)
IB
Full Range
25°C
-
-
1
ICC
mA RL=∞, All Op-Amps
Full Range
25°C
-
-
2.5
-
3.5
27
-
-
RL=2kΩ
Maximum Output Voltage (High)(Note 17)
Maximum Output Voltage (Low)(Note 17)
Large Signal Voltage Gain
VOH
VOL
AV
V
Full Range
Full Range
28
5
-
VCC=30V, RL=10kΩ
20
-
mV RL=∞
25
88
0
100
100
-
V/mV
RL≧2kΩ, VCC=15V
25°C
25°C
VOUT=1.4 to 11.4V
dB
-
VICM=VEE to (VCC-1.5V)
VOUT=1.4V
Input Common-mode Voltage Range
VICM
3.5
V
Input Common-mode Voltage Range
(VEE side) (Note 18)
VICM
Full Range
25°C
-
0.1
80
100
30
-
-
-
-
-
-
-
-
-
-
-
V
VOUT=1.4V
Common-mode Rejection Ratio
Power Supply Rejection Ratio
CMRR
PSRR
70
65
20
10
20
5
dB VOUT=1.4V
25°C
dB VCC=5 to 30V
25°C
V
+IN=1V, V-IN=0V
Output Source Current(Note 17,19)
ISOURCE
mA
VOUT=0V, Short Current
Full Range
25°C
27
-
V+IN=0V, V-IN=1V
mA
VOUT=5V, Short Current
Output Sink Current(Note 17,19)
ISINK
Full Range
25°C
V+IN=0V, V-IN=1V
VOUT=200mV
20
-
50
120
0.3
μA
Channel Separation
Slew Rate
CS
SR
GBW
θ
25°C
dB f=1kHz, Input Referred
VCC=15V, Av=0dB
V/μs
25°C
-
RL=2kΩ, CL=100pF
VCC=15V, VEE=-15V
RL=2kΩ, CL=100pF
Gain Bandwidth
Phase Margin
25°C
25°C
25°C
-
-
-
0.8
80
40
-
-
-
MHz
deg Av=40dB
VCC=15V, VEE=-15V
RS=100Ω, VIN=0V, f=1kHz
Input Referred Noise Voltage
VN
nV/ Hz
(Note 16) Absolute value
(Note 17) LM324xxx Full Range: TA=-40C to +85C, LM2902xxx Full Range: TA=-40C to +125C
(Note 18) LM2902xxx only.
(Note 19) Consider the power dissipation of the IC under high temperature when selecting the output current value.
There may be a case where the output current value is reduced due to the rise in IC temperature caused by the heat generated inside the IC.
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
4/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Description of Electrical Characteristics
Below are the descriptions of the relevant electrical terms used in this datasheet. Items and symbols used are also shown.
Note that item names, symbols, and their meanings may differ from those of another manufacturer’s document or general
document.
1. Absolute Maximum Ratings
Absolute maximum rating items indicate the conditions which must not be exceeded. Application of voltage in excess of the
absolute maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of
electrical characteristics.
(1) Supply Voltage (VCC/VEE
)
Indicates the maximum voltage that can be applied between the VCC pin and VEE pin without deterioration of
characteristics of internal circuit.
(2) Differential Input Voltage (VID)
Indicates the maximum voltage that can be applied between the non-inverting and inverting pins without damaging
the IC.
(3) Input Common-mode Voltage Range (VICM
)
Indicates the maximum voltage that can be applied to the non-inverting and inverting pins without deterioration or
destruction of electrical characteristics. Input common-mode voltage range of the maximum ratings does not assure
normal operation of IC. For normal operation, use the IC within the input common-mode voltage range characteristics.
(4) Power Dissipation (PD)
Indicates the power that can be consumed by the IC when mounted on a specific board at the ambient temperature 25°C
(normal temperature). As for package product, PD is determined by the temperature that can be permitted by the IC in
the package (maximum junction temperature) and the thermal resistance of the package.
2. Electrical Characteristics
(1) Input Offset Voltage (VIO)
Indicates the voltage difference between non-inverting pin and inverting pin. It can be translated to the input voltage
difference required for setting the output voltage to 0V.
(2) Input Offset Voltage Drift (∆VIO/∆T)
Denotes the ratio of the input offset voltage fluctuation to the ambient temperature fluctuation.
(3) Input Offset Current (IIO)
Indicates the difference of input bias current between the non-inverting and inverting pins.
(4) Input Bias Current (IB)
Indicates the current that flows into or out of the input pin. It is defined by the average of input bias currents at the
non-inverting and inverting pins.
(5) Supply Current (ICC
)
Indicates the current that flows within the IC under specified no-load conditions.
(6) Maximum Output Voltage (High) / Maximum Output Voltage (Low) (VOH/VOL
)
Indicates the voltage range of the output under specified load condition. It is typically divided into maximum output
voltage high and low. Maximum output voltage high indicates the upper limit of output voltage. Maximum output
voltage low indicates the lower limit.
(7) Large Signal Voltage Gain (AV)
Indicates the amplification rate (gain) of output voltage against the voltage difference between non-inverting pin and
inverting pin. It is normally the amplification rate (gain) with reference to DC voltage.
Av = (Output Voltage) / (Differential Input Voltage)
(8) Input Common-mode Voltage Range (VICM
)
Indicates the input voltage range at which IC normally operates.
(9) Common-mode Rejection Ratio (CMRR)
Indicates the ratio of fluctuation of input offset voltage when the input common-mode voltage is changed. It is normally
the fluctuation of DC.
CMRR = (Change of Input Common-mode Voltage)/(Input Offset Fluctuation)
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
5/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
(10) Power Supply Rejection Ratio (PSRR)
Indicates the ratio of fluctuation of input offset voltage when supply voltage is changed.
It is normally the fluctuation of DC.
PSRR= (Change of Power Supply Voltage)/( Input Offset Fluctuation)
(11) Output Source Current/ Output Sink Current (ISOURCE / ISINK
)
The maximum current that the IC can output under specific output conditions. The output source current indicates the
current flowing out from the IC, and the output sink current indicates the current flowing into the IC.
(12) Channel Separation (CS)
Indicates the fluctuation in the output voltage of the driven channel with reference to the change of output voltage of
the channel which is not driven.
(13) Slew Rate (SR)
Indicates the rate of the change of the output voltage with time when a step input signal is applied.
(14) Gain Bandwidth (GBW)
The product of the open-loop voltage gain and the frequency at which the voltage gain decreases 6dB/octave.
(15) Phase Margin (θ)
Indicates the margin of phase from 180 degree phase lag at unity gain frequency.
(16) Input Referred Noise Voltage (VN)
Indicates a noise voltage generated inside the operational amplifier equivalent by ideal voltage source connected in
series with input pin.
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
6/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves
○LM358xxx, LM2904xxx
1.6
1.2
0.8
0.4
0.0
1.6
1.2
0.8
0.4
0.0
25°C
36V
5V
85°C
-40°C
3V
125°C
-50 -25
0
25
50
75 100 125 150
0
10
20
SupplyVoltage [V]
30
40
AmbientTemperature [°C]
Figure 2. Supply Current vs Ambient
Temperature
Figure 1. Supply Current vs Supply Voltage
5
40
30
20
10
0
85°C
4
3
2
1
0
25°C
-40°C
0
10
20
30
40
-50 -25
0
25
50
75 100 125 150
SupplyVoltage [V]
AmbientTemperature [°C]
Figure 3. Maximum Output Voltage (High) vs
Figure 4. Maximum Output Voltage (High) vs
Supply Voltage (RL=10kΩ)
Ambient Temperature (VCC=5V, RL=10kΩ)
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM358xxx: -40°C to +85°C
LM2904xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
7/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves - continued
○LM358xxx, LM2904xxx
50
40
30
20
10
0
5
4
3
2
1
0
-40°C
25°C
85°C
125°C
-50 -25
0
25
50
75 100 125 150
0
1
2
3
4
5
Output Voltage [V]
AmbientTemperature [°C]
Figure 5. Maximum Output Voltage (High) vs
Ambient Temperature (VCC=5V, RL=2kΩ)
Figure 6. Output Source Current vs
Output Voltage (VCC=5V)
50
40
30
20
10
0
50
40
30
20
10
0
25°C
85°C
5V
125°C
36V
3V
-40°C
-50 -25
0
25
50
75 100 125 150
0
1
2
3
4
5
AmbientTemperature [°C]
Output Voltage [V]
Figure 7. Output Source Current vs
Ambient Temperature (VOUT=0V)
Figure 8. Output Sink Current vs
Output Voltage (VCC=5V)
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM358xxx: -40°C to +85°C
LM2904xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
8/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves - continued
○LM358xxx, LM2904xxx
102
50
40
30
20
10
0
100
36V
101
10
125°C
100
1
5V
85°C
25°C
10-1
0
3V
-40°C
10-2
0
10-3
0
-50 -25
0
25
50
75 100 125 150
0
0.5
1
1.5
2
AmbientTemperature [°C]
Output Voltage [V]
Figure 9. Output Sink Current vs Ambient
Figure 10. Low Level Sink Current vs
Output Voltage (VCC=5V)
Temperature (VOUT=VCC
)
100
1
80
60
40
20
0
36V
125°C
85°C
5V
3V
25°C
10-1
0
-40°C
10-2
0
0
0.25
0.5
0.75
1
-50 -25
0
25
50
75 100 125 150
Output Voltage [V]
AmbientTemperature [°C]
Figure 12. Low Level Sink Current vs Ambient
Temperature (VOUT=200mV)
Figure 11. Low Level Sink Current vs
Output Voltage (Enlarged view)
(VCC=5V)
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM358xxx: -40°C to +85°C
LM2904xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
9/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves - continued
○LM358xxx, LM2904xxx
4
3
4
3
2
2
1
1
125°C
85°C
25°C
36V
0
0
-1
-2
-3
-4
-1
-2
-3
-4
5V
3V
-40°C
-50 -25
0
25
50
75 100 125 150
0
10
20
SupplyVoltage [V]
30
40
AmbientTemperature [°C]
Figure 13. Input Offset Voltage vs Supply
Voltage (VICM=VCC/2, EK=-VCC/2)
Figure 14. Input Offset Voltage vs Ambient
Temperature (VICM=VCC/2, EK=-VCC/2)
100
90
80
70
60
50
40
30
20
10
0
50
40
30
20
10
0
-40°C
25°C
3V
5V
85°C
36V
125°C
-50 -25
0
25
50
75 100 125 150
0
10
20
30
40
AmbientTemperature [°C]
Supply Voltage [V]
Figure 16. Input Bias Current vs Ambient
Temperature (VICM=VCC/2, EK=-VCC/2)
Figure 15. Input Bias Current vs Supply
Voltage (VICM=VCC/2, EK=-VCC/2)
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM358xxx: -40°C to +85°C
LM2904xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
10/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves - continued
○LM358xxx, LM2904xxx
100
90
80
70
60
50
40
30
20
10
0
4
3
2
1
125°C
85°C
0
-1
-2
-3
-4
25°C
-40°C
-50 -25
0
25
50
75 100 125 150
-1
0
1
2
3
4
5
AmbientTemperature [°C]
Common-mode InputVoltage [V]
Figure 18. Input Offset Voltage vs
Common-mode Input Voltage (VCC=5V)
Figure 17. Input Bias Current vs Ambient
Temperature (VCC=30V, VICM=28V, EK=-1.4V)
10
8
10
8
6
6
4
4
-40°C
85°C
125°C
2
2
5V
36V
0
0
3V
-2
-4
-6
-8
-10
-2
-4
-6
-8
-10
25°C
0
10
20
SupplyVoltage [V]
30
40
-50 -25
0
25
50
75 100 125 150
AmbientTemperature [°C]
Figure 20. Input Offset Current vs Ambient
Temperature (VICM=VCC/2, EK=-VCC/2)
Figure 19. Input Offset Current vs Supply
Voltage (VICM=VCC/2, EK=-VCC/2)
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM358xxx: -40°C to +85°C
LM2904xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
11/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves - continued
○LM358xxx, LM2904xxx
0.6
0.5
0.4
0.3
0.2
0.1
0.0
0.6
0.5
0.4
0.3
0.2
0.1
0.0
125°C
125°C
85°C
85°C
25°C
-40°C
25°C
-40°C
0
10
20
SupplyVoltage [V]
30
40
0
10
20
SupplyVoltage [V]
30
40
Figure 21. Slew Rate Rise vs Supply Voltage
Figure 22. Slew Rate Fall vs Supply Voltage
(RL=2kΩ, Low to High)
(RL=2kΩ, High to Low)
100
80
60
40
20
0
80
60
40
20
0
240
180
120
60
Phase
Gain
0
108
101
102
103
104
102
103
104
105
106
107
Frequency [Hz]
Frequency[Hz]
Figure 23. Input Referred Noise Voltage vs
Frequency (VCC=5V)
Figure 24. Voltage Gain, Phase vs Frequency
(VCC=30V, RL=2kΩ, CL=100pF)
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM358xxx: -40°C to +85°C
LM2904xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
12/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves - continued
○LM358xxx, LM2904xxx
140
120
100
80
140
120
100
80
36V
85°C
25°C
5V
125°C
3V
-40°C
60
60
0
10
20
SupplyVoltage [V]
30
40
-50 -25
0
25
50
75 100 125 150
AmbientTemperature [°C]
Figure 25. Large Signal Voltage Gain vs
Figure 26. Large Signal Voltage Gain vs
Supply Voltage (RL=2kΩ)
Ambient Temperature (RL=2kΩ)
120
100
80
120
100
80
36V
-40°C
25°C
85°C
5V
3V
125°C
60
60
40
40
0
10
20
30
40
-50 -25
0
25
50
75 100 125 150
Supply Voltage [V]
AmbientTemperature [°C]
Figure 27. Common-mode Rejection Ratio vs
Supply Voltage
Figure 28. Common-mode Rejection Ratio vs
Ambient Temperature
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM358xxx: -40°C to +85°C
LM2904xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
13/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves - continued
○LM358xxx, LM2904xxx
140
120
100
80
60
-50 -25
0
25
50
75 100 125 150
AmbientTemperature [°C]
Figure 29. Power Supply Rejection Ratio vs
Ambient Temperature
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM358xxx: -40°C to +85°C
LM2904xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
14/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves - continued
○LM324xxx, LM2902xxx
2.0
1.6
1.2
0.8
0.4
0.0
2.0
1.6
1.2
0.8
0.4
0.0
36V
25°C
85°C
5V
-40°C
3V
125°C
-50 -25
0
25 50 75 100 125 150
0
10
20
SupplyVoltage [V]
30
40
AmbientTemperature [°C]
Figure 31. Supply Current vs Ambient
Temperature
Figure 30. 回路電流-電源電圧特性
5
40
125°C
85°C
4
3
2
1
0
30
20
10
0
25℃
-40°C
0
10
20
30
40
-50 -25
0
25
50
75 100 125 150
Supply Voltage [V]
AmbientTemperature [°C]
Figure 33. Maximum Output Voltage (High) vs
Figure 32. Maximum Output Voltage (High) vs
Ambient Temperature (VCC=5V, RL=10kΩ)
Supply Voltage (RL=10kΩ)
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM324xxx: -40°C to +85°C
LM2902xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
15/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves - continued
○LM324xxx, LM2902xxx
50
40
30
20
10
0
5
4
3
2
1
0
-40°C
25°C
85°C
125°C
-50 -25
0
25
50
75 100 125 150
0
1
2
3
4
5
AmbientTemperature [°C]
Output Voltage [V]
Figure 34. Maximum Output Voltage (High) vs
Figure 35. Output Source Current vs Output
Voltage (VCC=5V)
Ambient Temperature (VCC=5V, RL=2kΩ)
50
40
30
20
10
0
50
40
30
20
10
0
25°C
85°C
5V
125°C
36V
3V
-40°C
-50 -25
0
25
50
75 100 125 150
0
1
2
3
4
5
AmbientTemperature [°C]
Output Voltage [V]
Figure 36. Output Source Current vs Ambient
Temperature (VOUT=0V)
Figure 37. Output Sink Current vs Output
Voltage (VCC=5V)
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM324xxx: -40°C to +85°C
LM2902xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
16/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves - continued
○LM324xxx, LM2902xxx
102
50
40
30
20
10
0
100
36V
101
10
125°C
85°C
100
1
5V
25°C
10-1
0
3V
-40°C
10-2
0
10-3
0
-50 -25
0
25
50
75 100 125 150
0
0.5
1
1.5
2
AmbientTemperature [°C]
Output Voltage [V]
Figure 38. Output Sink Current vs Ambient
Figure 39. Low Level Sink Current vs
Output Voltage (VCC=5V)
Temperature (VOUT=VCC
)
0
1
10
80
60
40
20
0
36V
125°C
85°C
5V
3V
25°C
10-1
0
-40°C
10-2
0
0
0.25
0.5
0.75
1
-50 -25
0
25
50
75 100 125 150
Output Voltage [V]
AmbientTemperature [°C]
Figure 40. Low Level Sink Current vs
Output Voltage (Enlarged view)
(VCC=5V)
Figure 41. Low Level Sink Current vs Ambient
Temperature (VOUT=200mV)
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM324xxx: -40°C to +85°C
LM2902xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
17/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves - continued
○LM324xxx, LM2902xxx
4
3
4
3
2
2
1
1
36V
125°C
85°C
25°C
0
0
-1
-2
-3
-4
-1
-2
-3
-4
3V
5V
-40°C
-50 -25
0
25
50
75 100 125 150
0
10
20
SupplyVoltage [V]
30
40
AmbientTemperature [°C]
Figure 42. Input Offset Voltage vs Supply
Voltage (VICM=VCC/2, EK=-VCC/2)
Figure 43. Input Offset Voltage vs Ambient
Temperature (VICM=VCC/2, EK=-VCC/2)
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
-40°C
25°C
3V
5V
85°C
36V
125°C
-50 -25
0
25
50
75 100 125 150
0
10
20
30
40
AmbientTemperature [°C]
Supply Voltage [V]
Figure 45. Input Bias Current vs Ambient
Temperature (VICM=VCC/2, EK=-VCC/2)
Figure 44. Input Bias Current vs Supply
Voltage (VICM=VCC/2, EK=-VCC/2)
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM324xxx: -40°C to +85°C
LM2902xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
18/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves - continued
○LM324xxx, LM2902xxx
4
3
100
90
80
70
60
50
40
30
20
10
0
2
1
125°C
85°C
0
-1
-2
-3
-4
25°C
-40°C
-50 -25
0
25
50
75 100 125 150
-1
0
1
2
3
4
5
AmbientTemperature [°C]
Common-mode InputVoltage [V]
Figure 47. Input Offset Voltage vs
Common-mode Input Voltage (VCC=5V)
Figure 46. Input Bias Current vs Ambient
Temperature (VCC=30V, VICM=28V, EK=-1.4V)
10
8
10
8
6
6
4
4
-40°C
85°C
125°C
2
2
5V
36V
0
0
3V
-2
-4
-6
-8
-10
-2
-4
-6
-8
-10
25°C
-50 -25
0
25
50
75 100 125 150
0
10
20
Supply Voltage [V]
30
40
AmbientTemperature [°C]
Figure 49. Input Offset Current vs Ambient
Temperature (VICM=VCC/2, EK=-VCC/2)
Figure 48. Input Offset Current vs Supply
Voltage (VICM=VCC/2, EK=-VCC/2)
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM324xxx: -40°C to +85°C
LM2902xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
19/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves - continued
○LM324xxx, LM2902xxx
0.6
0.5
0.4
0.3
0.2
0.1
0.0
0.6
0.5
0.4
0.3
0.2
0.1
0.0
125°C
85°C
125°C
85°C
25°C
-40°C
25°C
-40°C
0
10
20
Supply Voltage [V]
30
40
0
10
20
SupplyVoltage [V]
30
40
Figure 50. Slew Rate Rise vs Supply Voltage
Figure 51. Slew Rate Fall vs Supply Voltage
(RL=2kΩ, Low to High)
(RL=2kΩ, High to Low)
100
80
60
40
20
0
80
60
40
20
0
240
180
120
60
Phase
Gain
0
108
101
102
103
104
102
103
104
105
106
107
Frequency[Hz]
Frequency[Hz]
Figure 52. Input Referred Noise Voltage vs
Frequency (VCC=5V)
Figure 53. Voltage Gain, Phase vs Frequency
(VCC=30V, RL=2kΩ, CL=100pF)
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM324xxx: -40°C to +85°C
LM2902xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
20/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves - continued
○LM324xxx, LM2902xxx
140
120
100
80
140
120
100
80
36V
85°C
25°C
5V
125°C
3V
-40°C
60
60
0
10
20
SupplyVoltage [V]
30
40
-50 -25
0
25
50
75 100 125 150
AmbientTemperature [°C]
Figure 54. Large Signal Voltage Gain vs
Figure 55. Large Signal Voltage Gain vs
Supply Voltage (RL=2kΩ)
Ambient Temperature (RL=2kΩ)
120
100
80
120
100
80
36V
-40°C
25°C
85°C
5V
3V
125°C
60
60
40
40
0
10
20
30
40
-50 -25
0
25
50
75 100 125 150
Supply Voltage [V]
AmbientTemperature [°C]
Figure 57. Common-mode Rejection Ratio vs
Ambient Temperature
Figure 56. Common-mode Rejection Ratio vs
Supply Voltage
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM324xxx: -40°C to +85°C
LM2902xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
21/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Typical Performance Curves - continued
○LM324xxx, LM2902xxx
140
120
100
80
60
-50 -25
0
25
50
75 100 125 150
AmbientTemperature [°C]
Figure 58. Power Supply Rejection Ratio vs
Ambient Temperature
(*) The above data are measurement value of typical sample, they are not guaranteed.
LM324xxx: -40°C to +85°C
LM2902xxx: -40°C to 125°C
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
22/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Application Information
NULL method condition for Test Circuit 1
VCC, VEE, EK, VICM Unit: V
Parameter
Input Offset Voltage
VF
VF1
VF2
VF3
VF4
VF5
VF6
VF7
VF8
VF9
VF10
SW1
ON
SW2
ON
SW3
VCC
VEE
0
EK
VICM Calculation
OFF 5 to 30
-1.4
-1.4
0
0
1
2
Input Offset Current
Input Bias Current
OFF
OFF
ON
OFF
ON
OFF
OFF
5
5
0
0
0
0
0
-1.4
0
0
3
4
5
6
OFF
-1.4
Large Signal Voltage Gain
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
15
5
-11.4
0
Common-mode Rejection Ratio
(Input Common-mode Voltage Range)
-1.4
-1.4
3.5
5
Power Supply Rejection Ratio
0
30
- Calculation -
|VF1|
1. Input Offset Voltage (VIO)
VIO
=
[V]
1 + RF/RS
|VF2 - VF1|
2. Input Offset Current (IIO)
3. Input Bias Current (IB)
IIO
=
[A]
RI x (1 + RF/RS)
|VF4 - VF3|
IB =
[A]
2 x RI x (1 + RF/RS)
EK × (1+RF/RS)
4. Large Signal Voltage Gain (AV)
[dB]
Av = 20Log
|VF6 - VF5|
VICM × (1+RF/RS)
5. Common-mode Rejection Ratio (CMRR)
[dB]
CMRR = 20Log
PSRR = 20Log
|VF8 - VF7|
VCC × (1+ RF/RS)
6. Power Supply Rejection Ratio (PSRR)
[dB]
|VF10 - VF9|
0.1μF
RF=50kΩ
500kΩ
SW1
0.1μF
VCC
15V
EK
RS=50Ω
RI=10kΩ
VOUT
500kΩ
DUT
SW3
NULL
-15V
1000pF
RI=10kΩ
RS=50Ω
RL
VICM
V VF
50kΩ
SW2
VEE
Figure 59. Test Circuit 1 (One Channel Only)
23/44
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Application Information – continued
Switch Condition for Test Circuit 2
Parameter
SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 SW9 SW10 SW11 SW12 SW13
Supply Current
OFF OFF OFF ON OFF ON OFF OFF OFF OFF OFF OFF OFF
OFF OFF ON OFF OFF ON OFF OFF ON OFF OFF ON OFF
OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF ON OFF
OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF OFF ON
OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF OFF ON
OFF OFF OFF ON OFF OFF OFF ON ON ON OFF OFF OFF
Maximum Output Voltage(High)
Maximum Output Voltage(Low)
Output Source Current
Output Sink Current
Slew Rate
Gain Bandwidth Product
Input Referred Noise Voltage
OFF
ON
ON OFF OFF ON ON OFF OFF ON ON OFF OFF OFF
OFF OFF OFF ON ON OFF OFF OFF OFF ON OFF OFF
SW4
R2
SW5
●
VCC
-
SW1
RS
SW2
SW3
+
SW9 SW10 SW11 SW12 SW13
SW6
SW7
SW8
R1
C
VEE
RL
CL
V-IN
V+IN
VOUT
Figure 60. Test Circuit 2 (Each Op-Amp)
Output Voltage
Input Voltage
SR=V/t
VH
VH
90%
V
10%
VL
VL
t
t
t
Input Wave
Output Wave
Figure 61. Slew Rate Input and Output Wave
VCC
VCC
R1//R2
R1//R2
VEE
VEE
R1
R2
VOUT1
R1
R2
V
VOUT2
V
VIN
= 1VRMS
100 × VOUT1
VOUT2
=
CS 20 × log
Figure 62. Test Circuit 3 (Channel Separation)
(R1=1kΩ,R2=100kΩ)
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
24/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Application Information – continued
VCC
1.
2.
Unused Circuits
It is recommended to apply the connection (see Figure 63) and set the
non-inverting input pin at a potential within the Input Common-mode
Voltage Range (VICM) for any unused circuit.
Keep this potential
VICM
in VICM
Input Voltage
Regardless of the supply voltage, applying VEE+36V to the input pin is
possible without causing deterioration of the electrical characteristics or
destruction. However, this does not ensure normal circuit operation.
Please note that the circuit operates normally only when the input
voltage is within the common mode input voltage range of the electric
characteristics.
VEE
Figure 63. The Example of Application
Circuit for Unused Op-amp
3.
4.
5.
Power Supply (Single/Dual)
The operational amplifiers operate when the voltage supplied is between VCC pin and VEE pin. Therefore, the single
supply operational amplifiers can be used as dual supply operational amplifiers as well.
IC Handling
When pressure is applied to the IC through warp on the printed circuit board, the characteristics may fluctuate due to
the piezo effect. Be careful with the warp on the printed circuit board.
The IC Destruction Caused by Capacitive Load
The IC may be damaged when VCC pin and VEE pin is shorted with the charged output pin capacitor. When IC is used
as an operational amplifier or as an application circuit where oscillation is not activated by an output capacitor, output
capacitor must be kept below 0.1µF in order to prevent the damage mentioned above.
I/O Equivalent Circuit
Symbol
Pin No.
Equivalent Circuit
LM358xxx, LM2904xxx: 2,3,5,6
LM324xxx, LM2902xxx:
2,3,5,6,9,10,12,13
+IN
-IN
VCC
LM358xxx, LM2904xxx: 1,7
LM324xxx, LM2902xxx: 1,7,8,14
OUT
OUT
VEE
VCC
LM358xxx, LM2904xxx: 8
LM324xxx, LM2902xxx: 4
VCC
VEE
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
25/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Examples of Circuit
○Voltage Follower
Voltage gain is 0dB.
VCC
Using this circuit, the output voltage (VOUT) is configured
to be equal to the input voltage (VIN). This circuit also
stabilizes the output voltage (VOUT) due to high input
impedance and low output impedance. Computation for
output voltage (VOUT) is shown below.
VOUT
VIN
VOUT=VIN
VEE
Figure 64. Voltage Follower Circuit
○Inverting Amplifier
R2
For inverting amplifier, input voltage (VIN) is amplified by
a voltage gain and depends on the ratio of R1 and R2.
The out-of-phase output voltage is shown in the next
expression
VCC
R1
VIN
VOUT
VOUT=-(R2/R1)・VIN
This circuit has input impedance equal to R1.
R1//R2
VEE
Figure 65. Inverting Amplifier Circuit
○Non-inverting Amplifier
R1
R2
For non-inverting amplifier, input voltage (VIN) is
amplified by a voltage gain, which depends on the ratio
of R1 and R2. The output voltage (VOUT) is in-phase with
the input voltage (VIN) and is shown in the next
expression.
VCC
VOUT=(1 + R2/R1)・VIN
VOUT
VIN
Effectively, this circuit has high input impedance since its
input side is the same as that of the operational amplifier.
VEE
Figure 66. Non-inverting Amplifier Circuit
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
26/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Power Dissipation
Power dissipation (total loss) indicates the power that the IC can consume at TA=25°C (normal temperature). As the IC
consumes power, it heats up, causing its temperature to rise above the ambient temperature. The allowable temperature that
the IC can accept is limited. This depends on the circuit configuration, manufacturing process, and consumable power.
Power dissipation is determined by the allowable temperature within the IC (maximum junction temperature) and the thermal
resistance of the package used (heat dissipation capability). Maximum junction temperature is typically equal to the
maximum storage temperature. The heat generated through the consumption of power by the IC radiates from the mold
resin or lead frame of the package. Thermal resistance, represented by the symbol θJA°C/W, indicates this heat dissipation
capability. Similarly, the temperature of an IC inside its package can be estimated by thermal resistance.
Figure 67(a) shows the model of the thermal resistance of a package. The equation below shows how to compute for the
Thermal resistance (θJA), given the ambient temperature (TA), maximum junction temperature (Tjmax), and power dissipation
(PD).
θJA
=
(Tjmax-TA) / PD
°C/W
The Derating Curve in Figure 67(b) indicates the power that the IC can consume with reference to ambient temperature.
Power consumption of the IC begins to attenuate at certain temperatures. This gradient is determined by Thermal resistance
(θJA), which depends on the chip size, power consumption, package, ambient temperature, package condition, wind velocity,
etc. This may also vary even when the same of package is used. Thermal reduction curve indicates a reference value
measured at a specified condition. Figures 67(c) to (f) show the examples of derating curves for LM358xxx, LM2904xxx,
LM324xxx, and LM2902xxx respectively.
Power Dissipation of LSI [W]
PDmax
P2
θJA=(Tjmax-TA)/ PD °C/W
θJA2 < θJA1
Ambient Temperature, TA [ °C ]
θJA2
P1
Tjmax
θJA1
150
0
25
50
75
100
125
Chip Surface Temperature, TJ [ °C ]
Ambient Temperature, TA [ °C ]
(b) Derating Curve
(a) Thermal Resistance
1.0
0.8
0.6
0.4
0.2
0.0
1.0
0.8
0.6
0.4
0.2
0.0
LM358F (Note 20)
LM358FJ (Note 21)
LM2904FVT (Note 22)
LM2904FV (Note 22)
LM358FVT (Note 22)
LM358FV (Note 22)
LM2904F (Note 20)
LM2904FJ (Note 21)
LM358FVJ (Note 23)
LM358FVM (Note 23)
LM2904FVJ(Note 23)
LM2904FVM (Note 23)
85
0
25
50
75
100
125
150
0
25
50
75
100
125
150
AmbientTemperature [°C]
(c) LM358xxx
AmbientTemperature [°C]
(d) LM2904xxx
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
27/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
1.5
1.2
0.9
0.6
0.3
0.0
1.5
1.2
0.9
0.6
0.3
0.0
LM324FJ (Note 25)
LM2902FJ (Note 25)
LM324FV (Note 26)
LM324FVJ (Note 27)
LM2902FV (Note 26)
LM2902FVJ (Note 27)
LM324F (Note 24)
LM2902F (Note 24)
85
0
25
50
75
100
125
150
0
25
50
75
100
125
150
AmbientTemperature [°C]
(e) LM324xxx
AmbientTemperature [°C]
(f) LM2902xxx
Note 20
5.5
Note 21
5.4
Note 22
5.0
Note 23
4.7
Note 24
4.5
Note 25
8.2
Note 26
7.0
Note 27
6.8
Unit
mW/°C
When using the unit above TA=25°C, subtract the value above per Celsius degree.
Power dissipation is the value when FR4 glass epoxy board 70mm×70mm×1.6mm (copper foil area below 3%) is mounted.
Figure 67. Thermal Resistance and Derating Curve
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
28/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Operational Notes
1.
Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply
pins.
2.
Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the
digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog
block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and
aging on the capacitance value when using electrolytic capacitors.
3.
4.
Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
5.
Thermal Consideration
Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in
deterioration of the properties of the chip. The absolute maximum rating of the PD stated in this specification is when
the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating,
increase the board size and copper area to prevent exceeding the PD rating.
6.
7.
Recommended Operating Conditions
These conditions represent a range within which the expected characteristics of the IC can be approximately obtained.
The electrical characteristics are guaranteed under the conditions of each parameter.
In-rush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow
instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply.
Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing
of connections.
8.
9.
Operation Under Strong Electromagnetic Field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject
the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should
always be turned off completely before connecting or removing it from the test setup during the inspection process. To
prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and
storage.
10. Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and
unintentional solder bridge deposited in between pins during assembly to name a few.
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
29/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Operational Notes – continued
11. Regarding the Input Pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them
isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a
parasitic diode or transistor. For example (refer to figure below):
When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic transistor.
Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual
interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to
operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be
avoided.
Figure 68. Example of monolithic IC structure
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
30/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Physical Dimensions, Tape and Reel Information
Package Name
SOP8
(Max 5.35 (include.BURR))
(UNIT : mm)
PKG : SOP8
Drawing No. : EX112-5001-1
<Tape and Reel information>
Tape
Embossed carrier tape
2500pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
31/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Physical Dimensions, Tape and Reel Information – continued
Package Name
SOP-J8
<Tape and Reel information>
Tape
Embossed carrier tape
2500pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
32/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Physical Dimensions, Tape and Reel Information – continued
Package Name
SSOP-B8
<Tape and Reel information>
Tape
Embossed carrier tape
2500pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
33/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Physical Dimensions, Tape and Reel Information – continued
Package Name
TSSOP-B8
<Tape and Reel information>
Tape
Embossed carrier tape
3000pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
34/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Physical Dimensions, Tape and Reel Information – continued
Package Name
TSSOP-B8J
<Tape and Reel information>
Tape
Embossed carrier tape
2500pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
35/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Physical Dimensions, Tape and Reel Information – continued
Package Name
MSOP8
<Tape and Reel information>
Tape
Embossed carrier tape
3000pcs
Quantity
TR
Direction
of feed
The direction is the 1pin of product is at the upper right when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
1pin
Direction of feed
Order quantity needs to be multiple of the minimum quantity.
Reel
∗
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
36/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Physical Dimensions, Tape and Reel Information – continued
Package Name
SOP14
(UNIT : mm)
PKG : SOP14
Drawing No. : EX113-5001
<Tape and Reel information>
Tape
Embossed carrier tape
2500pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
37/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Physical Dimensions, Tape and Reel Information – continued
Package Name
SOP-J14
<Tape and Reel information>
Tape
Embossed carrier tape
2500pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
38/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Physical Dimensions, Tape and Reel Information – continued
Package Name
SSOP-B14
<Tape and Reel information>
Tape
Embossed carrier tape
2500pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
39/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Physical Dimensions, Tape and Reel Information – continued
Package Name
TSSOP-B14J
<Tape and Reel information>
Tape
Embossed carrier tape
2500pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
40/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Ordering Information
L M
x
x
x
x
x
x
-
x
x
Part Number
LM358F
LM358FJ
LM358FV
LM358FVT
LM358FVJ
LM358FVM
LM324F
Package
F
Packaging and forming specification
E2: Embossed tape and reel
(SOP8/SOP-J8/SSOP-B8/
TSSOP-B8/ SOP14/SOP-J14/
SSOP-B14/TSSOP-B14J)
TR: Embossed tape and reel
(MSOP8)
: SOP8
: SOP14
: SOP-J8
: SOP-J14
: SSOP-B8
: SSOP-B14
: TSSOP-B8
: TSSOP-B8J
FJ
FV
FVT
FVJ
LM324FJ
LM324FV
LM324FVJ
LM2904F
: TSSOP-B14J
: MSOP8
FVM
LM2904FJ
LM2904FV
LM2904FVT
LM2904FVJ
LM2904FVM
LM2902F
LM2902FJ
LM2902FV
LM2902FVJ
Line-up
Operating Temperature Range
Channel
Package
Orderable Part Number
SOP8
Reel of 2500
Reel of 2500
Reel of 2500
Reel of 3000
Reel of 2500
Reel of 3000
Reel of 2500
Reel of 2500
Reel of 2500
Reel of 2500
Reel of 2500
Reel of 2500
Reel of 2500
Reel of 3000
Reel of 2500
Reel of 3000
Reel of 2500
Reel of 2500
Reel of 2500
Reel of 2500
LM358F-E2
SOP-J8
LM358FJ-E2
LM358FV-E2
LM358FVT-E2
LM358FVJ-E2
LM358FVM-TR
LM324F-E2
SSOP-B8
TSSOP-B8
TSSOP-B8J
MSOP8
2ch
-40°C to +85°C
SOP14
SOP-J14
SSOP-B14
TSSOP-B14J
SOP8
LM324FJ-E2
LM324FV-E2
LM324FVJ-E2
LM2904F-E2
LM2904FJ-E2
LM2904FV-E2
LM2904FVT-E2
LM2904FVJ-E2
LM2904FVM-TR
LM2902F-E2
LM2902FJ-E2
LM2902FV-E2
LM2902FVJ-E2
4ch
2ch
4ch
SOP-J8
SSOP-B8
TSSOP-B8
TSSOP-B8J
MSOP8
-40°C to +125°C
SOP14
SOP-J14
SSOP-B14
TSSOP-B14J
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
41/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Marking Diagram
SOP8(TOP VIEW)
SOP-J8(TOP VIEW)
Part Number Marking
Part Number Marking
LOT Number
LOT Number
1PIN MARK
1PIN MARK
TSSOP-B8(TOP VIEW)
SSOP-B8(TOP VIEW)
Part Number Marking
Part Number Marking
LOT Number
LOT Number
1PIN MARK
1PIN MARK
SOP14(TOP VIEW)
SOP-J14(TOP VIEW)
SSOP-B14(TOP VIEW)
TSSOP-B8J(TOP VIEW)
Part Number Marking
LOT Number
Part Number Marking
LOT Number
1PIN MARK
1PIN MARK
MSOP8(TOP VIEW)
Part Number Marking
LOT Number
Part Number Marking
LOT Number
1PIN MARK
1PIN MARK
TSSOP-B14J (TOP VIEW)
Part Number Marking
Part Number Marking
LOT Number
LOT Number
1PIN MARK
1PIN MARK
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
42/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Marking Diagram – continued
Product Name
Package Type
Marking
358L
F
FJ
SOP8
SOP-J8
FV
FVT
FVJ
FVM
F
SSOP-B8
TSSOP-B8
TSSOP-B8J
MSOP8
LM358
SOP14
LM324F
FJ
SOP-J14
SSOP-B14
TSSOP-B14J
SOP8
LM324FJ
LM324
LM2904
LM2902
FV
FVJ
F
324L
2904L
04L
FJ
SOP-J8
FV
FVT
FVJ
FVM
F
SSOP-B8
TSSOP-B8
TSSOP-B8J
MSOP8
2904L
SOP14
LM2902F
FJ
SOP-J14
SSOP-B14
TSSOP-B14J
LM2902FJ
FV
FVJ
2902L
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
43/44
Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
Revision History
Date
Revision
001
Changes
10.Jul.2015
09.Oct.2015
10.Feb.2016
06.Jun.2016
New Release
002
LM358FJ, LM358FV, LM358FVT, and LM324F are added
003
LM2904xxx (F, FJ, FV, FVT, FVM, FVJ), and LM358xxx (FVM, FVJ) are added
LM324xxx (FJ, FV, FVJ), and LM2902xxx (F, FJ, FV, FVJ) are added
004
Correction of erroneous description (P.4 Icc Full Range 1.5→2.5mA)
Delete Land Pattern Data(P.44)
01.Aug.2016
005
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
44/44
Notice
Precaution on using ROHM Products
1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PGA-E
Rev.003
© 2015 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PGA-E
Rev.003
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
Datasheet
LM2904F - Web Page
Part Number
Package
LM2904F
SOP8
Unit Quantity
2500
Minimum Package Quantity
Packing Type
Constitution Materials List
RoHS
2500
Taping
inquiry
Yes
相关型号:
LM2904H
DUAL OP-AMP, 9000uV OFFSET-MAX, 1.1MHz BAND WIDTH, MBCY8, METAL CAN, TO-99, 8 PIN
STMICROELECTR
©2020 ICPDF网 联系我们和版权申明