BU97931FV-LBE2 [ROHM]
Liquid Crystal Driver,;
| 型号： | BU97931FV-LBE2 |
| 厂家： | 
ROHM |
| 描述： | Liquid Crystal Driver, 驱动 接口集成电路 |
| 文件： | 总32页 (文件大小：914K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Datasheet
MAX 112 segments (SEG28×COM4)
Multifunction LCD Segment Driver
BU97931FV-LB
This is the product guarantees long time support in Industrial
market.
Key Specifications
■
■
■
■
■
■
■
Supply Voltage Range:
LCD Drive Power Supply Range:
Operating Temperature Range:
Max Segments:
+1.8V to +3.6V
Features
+2.7V to +5.5V
-40°C to +85°C
112 Segments
Long Time Support Product for Industrial Equipment
Integrated RAM for display data (DDRAM):
28 x 4 bit (Max 112 Segment)
Display Duty:
Bias:
Static, 1/3, 1/4 Selectable
Static, 1/3
LCD Drive Output:
4 Common Output, Max 28 Segment Output
Integrated 1ch LED Driver Circuit
Segment/GPO (Max 5port) Output Mode Selectable
Support PWM Generation from ext. or Internal Clock
(Resolution: 8bit)
Interface:
3Wire Serial Interface
Package
W (Typ) x D (Typ) x H (Max)
Support Standby Mode
Integrated Power-on-Reset Circuit (POR)
Integrated Oscillator Circuit
No External Component
Low Power Consumption Design
Independent Power Supply for LCD Driving
Support Blink Function
(Blink frequency 1.6, 2.0, 2.6, 4.0Hz selectable)
Applications
SSOP-B40
13.60mm x 7.80mm x 2.00mm
Industrial Equipment
Telephone
FAX
Portable Equipment (POS, ECR, PDA etc.)
DSC
DVC
Car audio
Home Electrical Appliance
Meter Equipment
Etc.
VLED=5.0V
Typical Application Circuit
LED/GPO using case
Regarding resistor value
Please detect the value according to
input current value (current MAX = 20mA)
VLCD
VDD
LED
Other
device
to
SEG27(GPO0)
SEG23(GPO4)
BU97931 FV-LB
.0V
3.3V
SEG0 toSEG22
VSS
CLKIN
CSB SD
SCL
LCD
to
COM0 COM3
CLKIN
External CLK input terminal
In case being unused, connect to VSS or be opened.
Input signal from controller
Figure 1.
Typical application circuit
○Product structure：Silicon monolithic integrated circuit ○This product has no designed protection against radioactive rays.
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
1/29
TSZ22111･14･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Block Diagram / Pin Configuration / Pin Description
SEG5
SEG4
SEG3
SEG2
SEG1
SEG6
COM0……COM3
LED
SEG0…22
SEG23...27
SEG7
VLCD
SEG8
Common
Driver
Segment
Driver
Segment
LED
LCD Voltage
Generator
Driver/GPO Driver
SEG9
SEG0
COM3
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
GPO
Controller
LCD
BIAS
SELECTOR
COM2
COM1
COM0
Blink
Timing
Generator
DDRAM
GPO Data Latch
Common
Counter
PWM
Generator
VLCD
CLKIN
VDD
VSS
Command Resister
Data Decoder
SD
CLKIN
OSCILLATOR
Power On
Reset
SCL
Serial Interface
IF FILTER
CSB
VDD
VSS
VSS
LED
SEG27
SEG26
SEG25
CSB
SD
SCL
Figure 2. Block Diagram
Figure 3. Pin Configuration (TOP VIEW)
Table 1 Pin Description
Terminal
Number
Unused
Case
Terminal
I/O
Function
CSB
SCL
26
27
I
I
-
Chip select: "L" active
Serial data transfer clock
-
SD
28
I
-
Input serial data
VDD
29
-
-
OPEN / VSS
-
Power supply for LOGIC
External clock input terminal (for display/PWM using selectable);
Support Hi-Z input mode at internal clock mode
CLKIN
VSS
30
I
25
-
GND
VLCD
31
-
-
Power supply for LCD
COMMON output for LCD
SEGMENT output for LCD
SEGMENT output for LCD/GPO
LED driver output
COM0 to 3
SEG0 to 22
SEG23 to 27
LED
32 to 35
O
O
O
O
OPEN
OPEN
OPEN
OPEN
36 to 40
1 to 18
19 to 23
24
www.rohm.com
TSZ02201-0P4P0D300490-1-2
© 2013 ROHM Co., Ltd. All rights reserved.
2/29
TSZ22111･15･001
26.Feb.2014 Rev.002
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Absolute Maximum Ratings (VSS=0V)
Parameter
Symbol
Ratings
Unit
Remarks
Power Supply Voltage 1
Power Supply Voltage 2
VDD
-0.3 to +4.5
-0.5 to +7.0
V
V
Power supply
Power supply for LCD
VLCD
When operated more than Ta=25°C, subtract 8.0mW
per degree. (using ROHM standard board)
(board size:74.2mm×74.2mm×1.6mm material: FR4
board copper foil: land pattern only)
Power Dissipation
Pd
0.8
W
Input Voltage Range
Operational Temperature
Range
Storage Temperature Range
Output current
VIN
-0.5 to VDD +0.5
-40 to +85
V
Topr
°C
°C
Tstg
Iout1
Iout2
Iout3
Iout4
-55 to +125
5
5
mA SEG output
mA COM output
mA GPO output
mA LED output
10
50
Caution:Operating the IC over the absolute maximum ratings may damage the IC.The damage can either be a short circui between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated
over the absolute maximum ratings.
Recommended Operating Conditions (Ta=-40°C to +85°C, VSS=0V)
Ratings
Parameter
Symbol
Unit
Remarks
Min
1.8
2.7
-
Typ
Max
3.6
5.5
20
Power Supply Voltage 1
Power Supply Voltage 2
Output Current
VDD
VLCD
Iout4
-
-
-
V
V
Power supply
Power supply for LCD
mA Per LED port 1ch
Electrical Characteristics
DC characteristics (Ta= -40°C to +85°C, VDD=1.8V to 3.6V, VLCD=3.3V to 5.5V, VSS=0)
Limits
Parameter
Symbol
Unit
Conditions
SD, SCL, CSB, CLKIN
Min
0.8VDD
VSS
-
Typ
-
Max
VDD
0.2VDD
-
“H” Level Input Voltage
“L” Level Input Voltage
Hysteresis Width
VIH
VIL
VH
V
V
V
-
SD, SCL, CSB, CLKIN
0.2
SCL, VDD=3.3V, Ta=25°C
SD, SCL, CSB, CLKIN,
VI=3.6V
SD, SCL, CSB, CLKIN,
VI=0V
Iload=-50µA, VLCD=5.0V
SEG0 to SEG27
Iload=-50µA, VLCD=5.0V,
COM0 to COM3
Iload=-1mA,VLCD=5.0V,
SEG23 to SEG27(GPO mode)
Iload= 50µA, VLCD=5.0V,
SEG0 to SEG27
Iload= 50µA, VLCD=5.0V,
COM0 to COM3
Iload=1mA, VLCD=5.0V,
SEG23 to SEG27(GPO mode)
Iload=20mA, VLCD=5.0V,
LED
“H” Level Input Current
“L” Level Input Current
IIH1
IIL1
-
-
5
-
µA
µA
V
-5
-
VLCD
-0.4
VLCD
-0.4
VLCD
-0.6
VOH1
VOH2
VOH3
VOL1
VOL2
VOL3
VOL4
-
-
“H” Level Output Voltage
-
-
V
(Note2)
-
-
V
-
-
-
-
-
0.4
0.4
0.5
0.5
V
-
-
V
“L” Level Output Voltage
(Note2)
V
0.11
V
(Note 1) Power save mode 1 and frame inversion setting
(Note 2) Iload: In this case, load current from only one port
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
3/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Electrical Characteristics – continued
DC characteristics (Ta= -40°C to +85°C, VDD=1.8V to 3.6V, VLCD=3.3V to 5.5V, VSS=0)
Limits
Parameter
Symbol
Unit
Conditions
Input terminal ALL’L’,
Display off, Oscillation off
Input terminal ALL’L’,
Display off, Oscillation off
VDD=3.3V, Ta=25°C, 1/3bias, fFR=64Hz,
Min
-
Typ
3
Max
10
IstVDD
µA
µA
IstVLCD
-
-
0.5
8
5
IVDD1
IVDD2
15
µA PWM generate off,
All output pin open
VDD=3.3V, Ta=25°C, 1/3bias, fFR=64Hz,
µA PWM Frequency=500Hz setting,
All output pin open
VLCD=5.0V, Ta=25°C, 1/3bias, fFR=64Hz,
µA LED generate off,
Current Consumption (Note1)
-
-
-
30
10
30
45
15
48
IVLCD1
IVLCD2
All output pin open
VLCD=5.0V, Ta=25°C, 1/3bias, fFR=64Hz,
µA PWM Frequency=500Hz setting,
All output pin open
(Note 1) Power save mode 1 and frame inversion setting
(Note 2) Iload: In case, load current from only one port
Oscillation Frequency Characteristics (Ta= -40°C to +85°C, VDD=1.8V to 3.6V, VLCD=2.7V to 5.5V, VSS=0)
Limits
Parameter
Symbol
Unit
Conditions
Min
57.6
51.2
45.0
Typ
64
64
-
Max
70.4
73.0
64
Frame Frequency 1
Frame Frequency 2
Frame Frequency 3
fFR1
fFR2
fFR3
Hz VDD=3.3V, Ta=25°C, fFR=64Hz setting
Hz VDD=2.5V to 3.6V fFR=64Hz setting
Hz VDD=1.8V to 2.5V fFR=64Hz setting
About detail function, please refer to the frame frequency setting of DISCTL command.
MPU Interface Characteristics (Ta= -40°C to +85°C, VDD=1.8V to 3.6V, VLCD=2.7V to 5.5V, VSS=0)
Limits
Parameter
Symbol
unit
Conditions
Min
-
Typ
Max
Input Rise Time
tr
-
-
-
-
-
-
-
-
-
-
50
50
-
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Input Fall Time
tf
-
SCL Cycle Time
“H” SCL PulseWwidth
“L” SCL Pulse Width
SD Setup Time
tSCYC
tSHW
tSLW
tSDS
tSDH
tCSS
tCSH
tCHW
250
50
50
50
50
50
50
50
-
-
-
SD Hold Time
-
CSB Setup Time
CSB Hold Time
-
-
“H” CSB Pulse Width
-
tCHW
CSB
tCSS
tCSH
tr
tSCYC
tf
tSLW
SCL
SD
tSHW
tSDS
tSDH
Figure 4. Serial Interface Timing
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
4/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
I/O Equivalence Circuit
VLCD
VSS
VD
VSS
VLCD
VD
SEG0-22
COM0-3
CSB, SD,
SCL,
VSS
CLKIN
VSS
LED
VSS
VLCD
SEG23-26
VSS
Figure 5. I/O Equivalence Circuit circuit
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
5/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Example of recommended circuit
(1) LED/GPO using case
VLED=5.0V
*Regarding resistor value
Please detect the value according to
input current value (current MAX = 20mA)
VLCD
VDD
LED
Other
device
to
SEG27(GPO0)
SEG23(GPO4)
BU97931FV-LB
5.0V
3.3V
SEG0 toSEG22
VSS
CLKIN
CSB SD
SCL
LCD
to
COM0 COM3
＊
CLKIN
External CLK input terminal
In case being unused, connect to VSS or be opened.
Input signal from controller
(2) SEG output only case
VLCD
VDD
LED
In case being unused, OPEN
BU97931FV-LB
5.0V
3.3V
SEG0 SEG27
to
VSS
CSB SD
SCL
CLKIN
LCD
COM0 COM3
to
CLKIN
＊
External CLK input terminal
In case being unused, connect to VSS or be opened.
Input signal from controller
Figure 6. BU97931FV-LB E.g. of recommended circuit
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
6/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Function description
Command and data transfer method
3-SPI (3-wire serial interface)
This device is controlled by a 3-wire signal (CSB, SCL, and SD).
First, Interface counter is initialized with CSB=“H".
Setting CSB=”L” enables SD and SCL inputs.
The protocol of 3-SPI transfer is as follows.
Each command starts with Command or Data judgment bit (D/C) as MSB data, followed by data D6 to D0 (this is when
CSB =”L”).
(Internal data is latched at the rising edge of SCL then it is converted to an 8-bit parallel data at the falling edge of the 8th
CLK.)
When CSB changes from “L” to “H”, and at this time sending commands are less than 8 bits, command and data transfer
are cancelled. To start sending command again, please set CSB=”L" and send command continuously.
After sending RAMWR or BLKWR or GPOSET command, this device is in the RAM data input mode. Under this mode,
device can not accept new commands.
In this case, please execute a “H” to “L” transition at CSB, after this sequence the device is released from RAM data input
mode, and can accept new command.
1st byte Command
2nd byte Command
3rd byte Command
CSB
SCL
SD
D/C
D6 D5 D4 D3 D2 D1 D0 D/C D6 D5 D4 D3 D2 D1 D0 D/C D6 D5 DD3 D2 D1 D0 D/C
D6
Figure 7. 3-SPI Data transfer Format
8-bit data sending after RAMWR command are display RAM data
8-bit data sending after BLKWR command are blink RAM data
SCL and SD can be set to “H” or cleared to “L” during CSB=”H”
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
7/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Write display data and transfer method
This device has Display Data RAM (DDRAM) of 28×4=112bit.
The relationship between data input and display data, DDRAM data and address are as follows.
1st Byte
2nd Byte
Command Command Command
10000011
00000000 10100000
…
j
a
g
p
b
c
h
i
k
l
m
n
o
d
e f
Display RAM data
RAM Write
Address set
According to this command, an 8-bit binary data will be written to DDRAM. The starting address of the DDRAM where
data will be written is specified by “ADSET" command, and is automatically incremented after every 4 bits of data
received.
Writing data to DDRAM can be done by continuously sending data.
(In case data is sent continuously after write date at 1Bh (SEG27), address return to address 00h (SEG0) automatically.)
In case SEG port assigned to GPO port by OUTSET command, corresponding SEG address do not change and is used
as a dummy address.
DDRAM address
00
a
01
e
f
02
03
m
n
04
05
06
07
・・・
19h
1Ah
1Bh
0
1
2
3
i
j
COM0
COM1
b
c
g
h
k
l
o
COM2
COM3
BIT
d
p
SEG
0
SEG
1
SEG
2
SEG
3
SEG
4
SEG
5
SEG
6
SEG
7
SEG
25
SEG
26
SEG
27
・・・
Display data write to DDRAM every 4bits.
In case CSB changes from ”L” to ”H” before 4 bits of data transfer was finished, RAM write is cancelled.
Display data
1st byte Command / 2nd byte Command
Command
CSB
SCL
SD
Address set command
RAMWR command
D7 D6 D5 D4 D3 D2 D1
D0
D7 D6 D5 D4 D3 D2 D1 D0
Internal
signal
RAM write
Address 02h
Address 01h
Address 00h
Data lower than 4bit case
RAM write is canceled
RAM write every 4bit
Display data
1st byte Command / 2nd byte Command
Command
CSB
SCL
SD
RAMWR command
Address set command
D7 D6 D5 D4 D3 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4
Internal
signal
RAM write
Address 31h
Address 00h
Address 30h
Addres00h
Auto increment
Return to address 00h
Figure 8. Display Data Transfer Method
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
8/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Blink function
This device has Blink function. Blink function can set each segment port individually.
Blink ON/OFF and Blink frequency are set by the BLKSET command.
Blink frequency varies according to fCLK characteristics.
Blink setup of each segment is controlled by BLKWR command.
The write start address is specified by “BLKADSET" command. And this address will automatically increment after
receiving every 4 bit s of blink data. The relation of BLKWR command, blink ram data, and blinking segment port is
below.
In case data is “1”, segment will blink, on the other hand when data is “0”, segment will not blink.
(In case data is written continuously after write data at 1Bh (SEG27), address will return to 00h (SEG0) automatically.)
Please refer to the following figures about Blink operation of each segment.
In case SEG port assigned to GPO port by OUTSET command, corresponding SEG address does not change and is
used as a dummy address.
1st Byte
Command
2nd Byte
Command
1st Byte
Command Command
2nd Byte
Command
11000000
10000100
00000011
10000111 00000000
Blink Address set
g
a
e
f
h
i
j
b
c
d
…
k
p
m
n
o
l
Blink
RAMWR
Blink RAM data
Blink set
Blink RAM address
00
01
02
03
04
05
06
07
・・・
19h
1Ah
1Bh
0
1
2
3
a
b
c
d
e
f
i
j
m
n
COM0
COM1
COM2
COM3
g
h
k
l
o
BIT
p
SEG
0
SEG
1
SEG
2
SEG
3
SEG
4
SEG
5
SEG
6
SEG
7
SEG
25
SEG
26
SEG
27
・・・
DDRAM data
SEG B
SEG A
SEG A
SEG C
SEG C
SEG D
SEG D
Blink RAM data
SEG B
Segment output
SEG D
SEG A
SEG B
SEG C
SEG D
SEG A
SEG B
SEG C
SEG D
SEG A
SEG B
SEG C
SEG D
SEG A
SEG B
SEG C
SEGA/B is blink
Blink frequency
under the 2Hz setting segment output will blink every 0.5 second (ON->OFF->ON)
Figure 9. Blink Operation
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
9/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
LCD Driver Bias/Duty Circuit
BU97931FV-LB generates LCD driving voltage using an on-chip Buffer AMP.
Also, it can drive LCD with low power consumption
Line and frame inversion can be set in MODESET command.
1/4duty, 1/3duty and static mode can be set DISCTL command.
About each LCD driving waveform, please refer to “LCD driving waveform” descriptions.
Initial state
Initial state after SWRST command input
○Display off
○All command register values are in Reset state.
○DDRAM address data and Blink address data are initialized
(If DDRAM data and Blink RAM data are not initialized, write DDRAM data and Blink RAM data before Display on.)
Command / Function list
Function description table
NO
Command
Function
1
2
Mode Set (MODESET)
Display control (DISCTL)
Sets LCD drive mode (display on/off, current mode)
Sets LCD drive mode
(frame freq., line/frame inversion)
3
Address set (ADSET)
Sets display data RAM address for RAMWR command
Sets Blink mode on/off
4
Blink set (BLKSET)
5
Blink address set (BLKADSET)
Sets Blink data RAM address for BLKWR command
Selects segment output/general purpose output (GPO)
Sets PWM1 signal “H” width for LED driving
Writes display data to display data RAM
Writes Blink data to BLINK data RAM
Sets all Pixel display on
SEG/GPO port change
(OUTSET)
6
LED drive control (PWMSET)
(H piece adjustment of PWM)
7
8
RAM WRITE (RAMWR)
9
Blink RAM WRITE (BLKWR)
All Pixel ON (APON)
10
11
12
13
14
15
All Pixel OFF (APOFF)
Sets all Pixel display off
All Pixel On/Off mode off (NORON)
Software Reset (SWRST)
OSC external input (OSCSET)
GPO output set (GPOSET)
Sets normal display mode (APON/APOFF cancel)
Software Reset
Enables External clock input
Sets GPO output data
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
10/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Detailed Command Descriptions
D/C, Data / Command judgment bit (MSB)
For details, please refer to 3-wire serial I/F
1. Mode Set (MODESET)
MSB
LSB
D0
1
D/C
1
D6
D5
0
D4
0
D3
0
D2
0
D1
0
Hex
81h
-
Reset
-
1st byte command
2nd byte command
0
0
0
0
0
P3
P2
P1
P0
00h
Display Set
Condition
P3
0
Reset state
Display OFF
Display ON
○
1
Display OFF: No LCD driving mode (Output: VSS Level)
Turn off OSC circuit and LCD power supply circuit. (Synchronized with frame freq)
Display ON: LCD driving mode
Turn on OSC circuit and LCD power supply circuit.
Read data from DDRAM and display to LCD.
LED port and GPO port output states are not influenced by a Display on/off state
Output state is decided by command setup (OUTSET, GPOSET, PWMSET) and INHb terminal state, respectively.
For more details, please refer to each command description.
LCD drive mode set
Condition
Frame inversion
Line inversion
P2
0
Reset state
○
1
Current mode set
Condition
P1
0
P0
0
Reset state
Power save mode1
Power save mode2
Normal mode
○
0
1
1
0
High power mode
1
1
(Reference data of consumption current)
Condition
Power save mode 1
Power save mode 2
Normal mode
Current consumption
×1.0
×1.7
×2.7
×5.0
High power mode
(Note) The value changes according to the panel load.
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
11/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
2. Display control (DISCTL)
MSB
D/C
1
LSB
D0
0
D6
0
D5
0
D4
0
D3
0
D2
0
D1
1
Hex
82h
-
Reset
-
1st byte Command
2nd byte Command
0
0
0
0
P3
P2
P1
P0
02h
Duty set
Condition
P3
0
P2
0
Reset state
1/4duty (1/3bias)
1/3duty (1/3bias)
○
0
1
Static (1/1bias)
1
*
*: Don’t care
In 1/3duty, Display data and Blink data of COM3 are ineffective.
COM1 and COM3 output are same data.
Please be careful in transmitting display data and blink data.
The examples of SEG/COM output waveform, under each Bias/Duty set up, are shown at "LCD Driver Bias/Duty
Circuit" description.
Frame frequency set
Condition
P1
P0
Reset state
(1/4,1/3,1/1duty)
(128Hz, 130Hz, 128Hz)
0
0
1
1
0
1
0
1
(85Hz, 86hz, 64Hz)
(64Hz, 65Hz, 48Hz)
(51Hz, 52Hz, 32Hz)
○
Relation table, between Frame frequencies (FR), integrated oscillator circuit (OSC) and Divide number.
Divide
FR [Hz] (Note1)
DISCTL
(P1,P0)
Duty set (P3,P2)
Duty set (P3,P2)
(0,0)
(0,1)
(1,*)
(0,0)
(0,1)
(1,*)
1/4duty
1/3duty
1/1duty
1/4duty
1/3duty
1/1duty
(0,0)
(0,1)
(1,0)
(1,1)
160
240
320
400
156
237
315
393
160
320
428
640
128
85.3
64
131.3
86.4
65
128
64
47.9
32
51.2
52.1
(Note1) FR is frame frequency, in case OSC frequency = 20.48KHz (typ).
The Formula, to calculate OSC frequency from Frame frequency is shown below.
“ OSC frequency = Frame frequency (measurement value) x Divide number ”
Divide number determined by using the value of Frame Frequency Set (P1, P0) and duty setting (P3, P2).
Ex) (P1,P0) = (0,1) ,(P3,P2) = (0,1) => Divide number= 237
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
12/29
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
3. Address set (ADSET)
MSB
D/C
1
LSB
D0
1
D6
0
D5
0
D4
0
D3
0
D2
0
D1
1
Hex
83h
-
Reset
-
1st byte Command
2nd byte Command
0
0
0
P4
P3
P2
P1
P0
00h
Sets start address to write DDRAM data.
The address can be set from 00h to 1Bh.
Do not set other address. (Except 00h to 1Bh address is not acceptable.)
In case writing data to DDRAM, make sure to send RAMWR command.
4. Blink set (BLKSET)
MSB
LSB
D0
0
D/C
1
D6
0
D5
0
D4
0
D3
0
D2
1
D1
0
Hex
84h
-
Reset
-
1st byte Command
2nd byte Command
0
0
0
0
0
P2
P1
P0
00h
Set Blink ON/OFF.
For more details, please refer to “Blink function".
Blink set
Blink mode(Hz)
P2
0
P1
0 / *
0
P0
0 / *
0
Reset state
OFF
1.6
2.0
2.6
4.0
○
1
1
0
1
1
1
0
1
1
1
*: Don’t care
5. Blink address set (BLKADSET)
MSB
LSB
D0
1
D/C
1
D6
D5
D4
0
D3
0
D2
D1
1
Hex
87h
-
Reset
-
1st byte Command
2nd byte Command
0
0
0
0
1
0
P4
P3
P2
P1
P0
00h
Sets RAM start address to write Blink data.
The address can be set from 00h to 1Bh.
Do not set other addresses. (Except 00h to 1Bh address is not acceptable)
In case writing data to Blink RAM, make sure to send BLKWR command.
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
13/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
6. SEG/GPO port change (OUTSET)
MSB
LSB
D0
0
D/C
D6
0
D5
0
D4
0
D3
1
D2
0
D1
0
Hex
88h
-
Reset
-
1st byte Command
2nd byte Command
1
0
0
0
0
0
P2
P1
P0
00h
Set output mode, Segment output or GPO output.
P2 to P0: Select changing port number. (SEG23 to SEG27 ports are SEG mode/GPO mode selectable)
In case GPO output is selected, terminal output data is set by GPOSET command.
Ex) In case SEG 26 port is assigned to GPO,
If GPO1 data is "H", GPO1 (SEG26) port outputs "H" (VLCD Level).
If GPO1 data is "L", GPO1 (SEG26) port outputs "L" (VSS level).
Output terminal state under the P2 to P0 set condition is listed below.
Output Terminal state
Condition
SEG Terminal state (SEG output/GPO output)
P2
0
P1
0
P0
0
SEG23 port
SEG23
SEG23
SEG23
SEG23
SEG23
GPO4
SEG24 port
SEG24
SEG24
SEG24
SEG24
GPO3
SEG25 port
SEG25
SEG25
SEG25
GPO2
SEG26 port
SEG26
SEG26
GPO1
SEG27 port
SEG27
GPO0
GPO0
GPO0
GPO0
GPO0
0
0
1
0
1
0
0
1
1
GPO1
1
0
0
GPO2
GPO1
1
0
1
GPO3
GPO2
GPO1
1
1
*
(OUTSET command will be canceled)
In case the SEG port is switched to the GPO port, DDRAM address and Blink RAM address do not change.
In case DDRAM address and Blink RAM address, selected GPO output mode is dummy address.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
14/29
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
7. LED drive-control (PWM “H” width control) command (PWMSET)
MSB
LSB
D0
0
D/C
1
D6
0
D5
0
D4
0
D3
1
D2
0
D1
1
Hex
Reset
-
1st byte Command
2nd byte Command
3rd byte Command
8Ah
0
0
0
0
0
0
P7
P1
P6
P0
-
-
00h
00h
0
0
P5
P4
P3
P2
2nd and 3rd byte command data can be set from 00h to 3Fh (described as 8-bit binary data).
In case other value is selected, sending command is ignored and 2nd and 3rd byte command data are set to 3Fh.
In reset state, 2nd and 3rd byte command data are set to 00h.
In case the command is less than 3 byte, sending command is cancelled.
According to PWMSET command, LED driving signal is adjustable. PWM “H” width is adjustable by 8-bit resolution.
Explanation about P7 to P6 data of 2nd byte command and P5 to P0 data of 3rd byte command are as follows:
(The 2nd byte data are used as upper 2bit, and 3rd byte data are used as lower 6 bits.)
8bit mode: P7 data is used as MSB of 8 bits, and P0 data is used LSB.
LED driving period is determined by the “H” width of PWM signal, generated by PWM generator circuit (resolution: 8bit).
Ex)
In case external PWM clock is 125 KHz, parameter setting value is 127 (7Fh)
1-bit resolution: 8us
ALL HI set: PWM signal frequency about 500Hz, H width about 2.00msec
ALL LOW set: PWM signal frequency about 500Hz, H width 0usec (in case 8bit resolution)
This command is reflected, synchronizing with a next PWM frame head.
And, LED port output is as follows. LED port operation does not affect Display ON/OFF state.
FFh
(H width: wide)
PWM (ALL HI）
Duty shift
00h
(H width: narrow）
PWM (ALL Low）
(Note) PWM frequency and PWM “H” width calculation
PWM cycle and PWM “H” width, decided by PWM clock cycle are described as follows.
(PWM clock cycle is a minimum unit of PWM “H” width)
PWM frequency = PWM clock cycle × (Number of the steps (8bit =256) - 1)
PWM H width = PWM clock cycle × Parameter set value (8bit: 0 to 255)
PWM Duty = PWM H width/PWM cycle = Parameter set value / Number of the steps
In case PWM is generated from the internal clock, the PWM cycle varies depending on the OSC frequency.
In case LED is used as back light of LCD panel and PWM is generated from internal clock,
there is a possibility that the display will flicker. For such cases, please use under the PWM width ALL “L”
or ALL “H” setting only.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
15/29
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
8. RAM WRITE (RAMWR)
MSB
D/C
1
LSB
D0
0
D6
0
D5
1
D4
0
D3
0
D2
0
D1
0
Hex
A0h
Reset
-
1st byte Command
2nd byte Command
Display data
・・・・
Random
n byte Command
Display data
Random
Input data, sending after 1st byte command, are used as Display data. And display data are sent every 4 bits. Please set
this command after the ADSET command.
9. Blink RAM WRITE (BLKWR)
MSB
D/C
1
LSB
D0
0
D6
1
D5
0
D4
0
D3
0
D2
0
D1
0
Hex
C0h
Reset
-
1st byte Command
2nd byte Command
Blink data
・・・・
Blink data
Random
n byte Command
Random
Input data, sending after 1st byte command, are used as Display data. And display data are sent every 4 bits. Please set
this command after the BLKADSET command.
10. All Pixel ON (APON)
MSB
D/C
1
LSB
D0
1
D6
0
D5
0
D4
1
D3
0
D2
0
D1
0
Hex
91h
Reset
-
1st byte Command
After sending the command, all SEG outputs set display on state regardless of the DDRAM data.
(This command affect to the SEG output terminal only except GPO and LED output.)
11. All Pixel OFF (APOFF)
MSB
D/C
1
LSB
D0
0
D6
0
D5
0
D4
1
D3
0
D2
0
D1
0
Hex
90h
Reset
-
1st byte Command
After sending the command, all SEG outputs set display off state regardless of the DDRAM data.
(This command affects the SEG output terminals only except GPO and LED outputs.)
12. All Pixel ON/OFF mode off (NORON)
MSB
D/C
1
LSB
D0
1
D6
0
D5
0
D4
1
D3
0
D2
0
D1
1
Hex
93h
Reset
-
1st byte Command
After sending the command, all SEG outputs are released from APON/APOFF state.
And SEG port outputs signal follows DDRAM data.
(This command affects the SEG output terminals only except GPO and LED output.)
After reset sequence or SWRESET, all outputs are set to NORON state.
13. Software Reset (SWRST)
MSB
D/C
1
LSB
D0
0
D6
0
D5
0
D4
1
D3
0
D2
0
D1
1
Hex
92h
Reset
-
1st byte Command
After sending the command, device is set to the default state.
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
16/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
14. OSC external input command (OSCSET)
MSB
LSB
D0
0
D/C
1
D6
0
D5
0
D4
1
D3
1
D2
0
D1
0
Hex
98h
-
Reset
-
1st byte Command
2nd byte Command
0
0
0
0
0
P2
P1
P0
00h
Sets the type of clock mode. There are 4 selectable modes including external clock input mode.
Details of this command function are as follows.
Condition
P2
0
P1
0
P0
0
Reset state
Internal CLK (PWM generation OFF)
○
External CLK input for PWM (PWM generation OFF)
Internal CLK (PWM generation ON）
0
0
1
0
1
0
External CLK input for PWM (PWM generation ON)
0
1
1
External CLK input for Display (ROHM use only)
1
*
*
(*: Don’t care)
(P2, P1, P0) = (0, 0, 1): External PWM input mode
CLKIN：external PWM input available.
PWMOUT: “L” Output
(Note) under the (P2, P1, P0) = (0, 0, 0) condition PWMOUT into same state
(P2, P1, P0) = (0, 1, 0): PWM is generated from an internal oscillating frequency
(P2, P1, P0) = (0, 1, 1): PWM is generated from an External CLK input from CLKIN
PWM width is set up by PWMSET and PWMSET command.
In case LED is used as back light of LCD panel and PWM is generated from internal clock, display flickering will
occur. In this case, please use under the PWM width ALL”L” or ALL “H” setting only.
The relation of OSC function control by each command is as follows:
Integrated OSC
LED
CLKIN terminal
External clock
PWM
generation
External PWM
PWMSET
command
OSCSET
command
Figure 10. OSC External Input
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
17/29
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
15. GPO output set command (GPOSET)
MSB
LSB
D0
0
D/C
D6
0
D5
0
D4
1
D3
1
D2
0
D1
1
Hex
9Ah
-
Reset
1st byte Command
2nd byte Command
1
0
-
0
0
P4
P3
P2
P1
P0
00h
Set GPO output data. The relation between SEG port (GPO port) and data is shown below.
GPOSET data
GPO port
GPO0
GPO1
GPO2
GPO3
GPO4
SEG port
SEG27
SEG26
SEG25
SEG24
SEG23
P0
P1
P2
P3
P4
GPO data output is asynchronous from frame cycle.
In case INHb=”H”, GPO output signal follows GPOSET data, on the other hand, in case INHb=”L” GPO output is at
GND level. GPO output is not affected by Display ON/OFF state.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
18/29
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
LCD driving waveform
1/4Duty
Line inversion
Frame inversion
SEGn SEGn+1SEGn+2SEGn+3
SEGn SEGn+1SEGn+2SEGn+3
COM0
stateA
stateB
COM0
COM1
COM2
COM3
stateA
stateB
COM1
COM2
COM3
1frame
1frame
Vreg
Vreg
COM0
COM0
COM1
VSS
Vreg
VSS
Vreg
COM1
VSS
Vreg
VSS
Vreg
COM2
COM2
VSS
Vreg
VSS
Vreg
COM3
COM3
VSS
Vreg
VSS
Vreg
SEGn
SEGn
VSS
Vreg
VSS
Vreg
SEGn+1
SEGn+1
SEGn+2
SEGn+3
VSS
Vreg
VSS
Vreg
SEGn+2
VSS
Vreg
VSS
Vreg
SEGn+3
VSS
Vreg
VSS
Vreg
stateA
stateA
(COM0-SEGn)
(COM0-SEGn)
-Vreg
Vreg
-Vreg
Vreg
stateB
stateB
(COM1-SEGn)
(COM1-SEGn)
-Vreg
-Vreg
Figure 11. Waveform of Line Inversion
Figure 12. Waveform of Frame Inversion
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
19/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
1/3Duty
Line inversion
Frame inversion
SEGn SEGn+1 SEGn+2 SEGn+3
SEGn SEGn+1 SEGn+2 SEGn+3
COM0
COM1
COM2
COM3
stateA
stateB
COM0
COM1
COM2
COM3
stateA
stateB
When 1/3duty
When1/3duty
COM3 and COM1 is same
COM3 and COM1 is same
1frame
1frame
Vreg
Vreg
COM0
COM0
COM1
VSS
Vreg
VSS
Vreg
COM1
VSS
Vreg
VSS
Vreg
COM2
COM2
VSS
Vreg
VSS
Vreg
When 1/3duty
COM3 and COM1
is same
COM3
COM3
VSS
Vreg
VSS
Vreg
SEGn
SEGn
VSS
Vreg
VSS
Vreg
SEGn+1
SEGn+1
SEGn+2
SEGn+3
VSS
Vreg
VSS
Vreg
SEGn+2
VSS
Vreg
VSS
Vreg
SEGn+3
VSS
Vreg
VSS
Vreg
stateA
(COM0-SEGn)
stateA
(COM0-SEGn)
-Vreg
Vreg
-Vreg
Vreg
stateB
(COM1-SEGn)
stateB
(COM1-SEGn)
-Vreg
-Vreg
Figure 13. Waveform of Line Inversion
Figure 14. Waveform of Frame Inversion
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
20/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
1/1Duty (Static)
Line inversion
Frame inversion
SEGn SEGn+1 SEGn+2 SEGn+3
SEGn SEGn+1 SEGn+2 SEGn+3
stateA stateB
COM0
COM1
COM2
COM3
stateA stateB
COM0
COM1
COM2
COM3
When 1/1duty (Static)
COM1 / COM0 is same
waveform
When 1/1duty (Static)
COM1 / COM0 is same
waveform
COM2 / COM0 is same
waveform
COM2 / COM0 is same
waveform
1frame
1frame
Vreg
Vreg
COM0
COM0
COM1
VSS
Vreg
VSS
Vreg
When 1/1duty
(Static)
COM1
COM1 / COM0
is same
VSS
Vreg
VSS
Vreg
waveform
COM2 / COM0
is same
COM2
COM2
waveform
VSS
Vreg
VSS
Vreg
COM3 / COM0
is same
COM3
COM3
waveform
VSS
Vreg
VSS
Vreg
SEGn
SEGn
VSS
Vreg
VSS
Vreg
SEGn+1
SEGn+1
SEGn+2
SEGn+3
VSS
Vreg
VSS
Vreg
SEGn+2
VSS
Vreg
VSS
Vreg
SEGn+3
VSS
Vreg
VSS
Vreg
stateA
stateA
-Vreg
Vreg
-Vreg
Vreg
stateB
stateB
-Vreg
-Vreg
Figure 15. Waveform of Line Inversion
Figure 16. Waveform of Frame Inversion
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
21/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Initialize Sequence
Recommended input sequence is listed below, before starting LCD driving.
(Refer to Power ON/OFF sequence)
Input voltage supply
↓
CSB ’H’
…interface initializing
…interface command sending
…software reset
↓
CSB ’L’
↓
SWRST
↓
MODESET
…Display off
↓
Various commands setting
↓
RAM WRITE
↓
Blink RAM WRITE
↓
MODESET
…Display on
↓
Start LCD driving
Before initializing sequence, DDRAM address, DDRAM data, Blink address and Blink data are random.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
22/29
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Cautions on Power-On/ Power-Off condition
POR circuit
BU97931FV-LB has “P.O.R” (Power-On Reset) circuit and Software Reset function.
Please follow the recommended Power-On conditions in order to power up properly.
(1) Please set power up conditions, follow the recommended tR, tF, tOFF, and Vbot specification below in order to
ensure P.O.R operation.
(*The detection voltage of POR varies because of environment etc. To operate POR properly, please satisfy
Vbot lower than 0.5V condition.)
VDD
tR
Recommended condition of tR, tF, tOFF, Vbot
tR
tOFF
Vbot
VDET
VDET
less than
10ms
Over
1ms
less than
0.5V
TYP
1.2V
tOFF
Vbot
* VDET : POR detect level
Figure 17. Power ON/OFF Waveform
(2) If it is difficult to meet the above conditions, execute the following sequence after Power-On.
(1) CSB=”L”→”H” condition
(2) After CSB”H”→“L”, execute SWRST command
In addition, in order to the Software reset command certainly, please wait 1ms after a VDD level
reaches to 90% and CSB=”L”→”H”.
*Before SWRST command input device will be in unstable state, since SWRST command does not
operate perfect substitution of a POR function.
VDD
CSB
Min 1ms
Min 50ns
SWRST
Command
Figure 18. SWRST Command Sequence
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
23/29
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Attention about input port pull down
Satisfy the following sequence if input terminals are pulled down by external resistors (In case MPU output Hi-Z).
Input "L"
period
Input"Hi-Z"
period
Date transaction period with MPU
CSB
SD
SCL
Figure 19. Recommended Sequence when Input Ports are Pulled Down
BU97931FUV-LB adopts a 5V tolerant I/O for the digital input. This circuit includes a bus-hold function to keep HIGH level.
A pull down resistor of below 10KΩ shall be connected to the input terminals for transitions from HIGH to LOW because the
bus-hold transistor turns on during the input’s HIGH level. (Refer to the Figure 5; I/O Equivalent Circuit)
A higher resistor than 10KΩ(approximate) causes input terminals being steady by intermediate potential between HIGH and
LOW level so unexpected current is consumed by the system.
The potential depends on the pull down resistance and bus-hold transistor’s resistance.
As the bus-hold transistor turns off upon the input level is cleared to LOW, a higher resistor can be used as a pull down
resistor if MPU sets SD and SCL lines to LOW before it releases the lines.
The LOW period preceding MPU’s bus release shall be at least 50ns as same as a minimum CLK width ( tSLW ).
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
24/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Operational Notes
1.
2.
Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply
pins.
Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the
digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog
block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and
aging on the capacitance value when using electrolytic capacitors.
3.
4.
Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
5.
Thermal Consideration
Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in
deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when
the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating,
increase the board size and copper area to prevent exceeding the Pd rating.
6.
7.
Recommended Operating Conditions
These conditions represent a range within which the expected characteristics of the IC can be approximately obtained.
The electrical characteristics are guaranteed under the conditions of each parameter.
Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush
current may flow instantaneously due to the internal powering sequence and delays, especially if the IC
has more than one power supply. Therefore, give special consideration to power coupling capacitance,
power wiring, width of ground wiring, and routing of connections.
8.
9.
Operation Under Strong Electromagnetic Field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject
the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should
always be turned off completely before connecting or removing it from the test setup during the inspection process. To
prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and
storage.
10. Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and
unintentional solder bridge deposited in between pins during assembly to name a few.
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
25/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Operational Notes – continued
11. Unused Input Pins
Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and
extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge
acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause
unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power
supply or ground line.
12. Regarding the Input Pin of the IC
In the construction of this IC, P-N junctions are inevitably formed creating parasitic diodes or transistors. The operation
of these parasitic elements can result in mutual interference among circuits, operational faults, or physical damage.
Therefore, conditions which cause these parasitic elements to operate, such as applying a voltage to an input pin lower
than the ground voltage should be avoided. Furthermore, do not apply a voltage to the input pins when no power
supply voltage is applied to the IC. Even if the power supply voltage is applied, make sure that the input pins have
voltages within the values specified in the electrical characteristics of this IC.
13. Ceramic Capacitor
When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with
temperature and the decrease in nominal capacitance due to DC bias and others.
14. Area of Safe Operation (ASO)
Operate the IC such that the output voltage, output current, and power dissipation are all within the Area of Safe
Operation (ASO).
15. Thermal Shutdown Circuit(TSD)
This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation should always be
within the IC’s power dissipation rating. If however the rating is exceeded for a continued period, the junction
temperature (Tj) will rise which will activate the TSD circuit that will turn OFF all output pins. When the Tj falls below the
TSD threshold, the circuits are automatically restored to normal operation.
Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no
circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from heat
damage.
16. Over Current Protection Circuit (OCP)
This IC incorporates an integrated overcurrent protection circuit that is activated when the load is shorted. This
protection circuit is effective in preventing damage due to sudden and unexpected incidents. However, the IC should
not be used in applications characterized by continuous operation or transitioning of the protection circuit.
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
26/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Ordering Information
B
U
9
7
9
3
1
F
V - L B E 2
Products Class
Package
FV
Part Number
LB for Industrial applications
Packaging and forming specification
E2: Embossed tape and reel
(SSOP-B40)
: SSOP-B40
Marking Diagram
SSOP-B40 (TOP VIEW)
Part Number Marking
LOT Number
B U 9 7 9 3 1
1PIN MARK
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
27/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Physical Dimension, Tape and Reel Information
Package Name
SSOP-B40
(Max 13.95 (include. BURR)
<Tape and Reel information>
Tape
Embossed carrier tape
2000pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
28/29
TSZ22111･15･001
Daattaasshheeeett
BU97931FV-LB
MAX 112 segments (SEG28×COM4)
Revision History
Date
Revision
Changes
23.Aug.2013
001
002
New Release
Delete sentence “and log life cycle” in General Description and Futures.
Applied new style (change of the size of the title).
26.Feb.2014
www.rohm.com
TSZ02201-0P4P0D300490-1-2
26.Feb.2014 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
29/29
TSZ22111･15･001
Daattaasshheeeett
Notice
Precaution on using ROHM Products
(Note 1)
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment
,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice - SS
Rev.002
© 2014 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice - SS
Rev.002
© 2014 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2014 ROHM Co., Ltd. All rights reserved.
相关型号：
©2020 ICPDF网 联系我们和版权申明