BU4021BFE2 [ROHM]
4000/14000/40000 SERIES, 8-BIT RIGHT PARALLEL IN SERIAL OUT SHIFT REGISTER, TRUE OUTPUT, PDSO16, ROHS COMPLIANT, SOP-16;
| 型号： | BU4021BFE2 |
| 厂家： | 
ROHM |
| 描述： | 4000/14000/40000 SERIES, 8-BIT RIGHT PARALLEL IN SERIAL OUT SHIFT REGISTER, TRUE OUTPUT, PDSO16, ROHS COMPLIANT, SOP-16 光电二极管 输出元件 逻辑集成电路 触发器 |
| 文件： | 总16页 (文件大小：568K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Datasheet
General Purpose CMOS Logic IC
8bit Static Shift Resister
BU4021BF
General Description
Key Specifications
BU4021BF is an 8bit static shift resister.It consists of eight
resister stages and each register has an parallel input. A
serial input/serial output function or a parallel input/serial
output function can be selected by a parallel/serial input
selection pin (P/S).
Operating Supply Voltage Range:
+3V to +16V
0V to VDD
-40°C to +85°C
Input Voltage Range:
Operating Temperature Range:
Packages
W(Typ) x D(Typ) x H(Max)
10.00mm x 6.20mm x 1.71mm
Features
SOP16
Low Power Consumption
Wide Operating Supply Voltage Range
High Input Impedance
High Fan Out
2 L-TTL Inputs or 1 LS-TTL Input can be directly
driven
Truth Table
Pin Configurations
Serial Input－Serial Output
(Top View)
Input
P1
Output
CLOCK
P/S
L
Pn
X
DS
L
Q1
Qn
1
2
16
VDD
P8
Q6
X
X
X
L
Qn-1
Qn-1
15 P7
L
X
H
H
Q8 3
14 P6
L
X
X
No Change
P4
P3
13 P5
4
5
6
7
8
Parallel Input－Serial Output
12 Q7
11 DS
10 CLOCK
9 P/S
Input
Output
CLOCK
P/S
H
P1
L
Pn
L
DS
X
Q1
L
Qn
L
P2
X
X
X
X
P1
H
L
H
L
X
L
H
L
VSS
H
H
H
X
H
H
H
H
X
H
X: Don’t Care
Qn: Q6,Q7,Q8 are outside of IC
○Product structure：Silicon monolithic integrated circuit ○This product has not designed protection against radioactive rays
.www.rohm.com
TSZ02201-0RDR1GZ00230-1-2
04.Sep.2013 Rev.001
© 2013 ROHM Co., Ltd. All rights reserved.
1/13
TSZ22111・14・001
Daattaasshheeeett
BU4021BF
Logic Diagram
P3,P4,P5
are same
with P1,P2
P1
P2
P6
P7
P8
P/S
DS
SET
SET
SET
SET
SET
Q1
Q2
Q
Q
Q
Q
Q
D
D
D
D
D
CLK
CLK
CLK
CLK
CLK
RESET
RESET
RESET
RESET
RESET
CLOCK
Q8
Q6
Q7
Timing Chart
P/S
5
6
7
9
3
4
8
2
1
CLOCK
DS1
DS2
DS3
DS4
DS5
DS6
DS7
DS8
DS
DP1
DP2
DS1
DP1
DS2
DS1
DS3
DS2
DS4
DS5
DS6
DS5
DS7
DS6
DS8
Q1
Q2
DS3
DS7
DS4
・
・
・
DP6
DP5
DP4
DP3
DP2
DP1
DS1
DS2
DS2
Q6
DP7
DP8
DP6
DP7
DP5
DP6
DP4
DP5
DP3
DP4
DP2
DP3
DP1
DP2
DS1
DP1
DS2
DS1
Q7
Q8
www.rohm.com
TSZ02201-0RDR1GZ00230-1-2
04.Sep.2013 Rev.001
© 2013 ROHM Co., Ltd. All rights reserved.
2/13
TSZ22111・15・001
Daattaasshheeeett
BU4021BF
Pin Descriptions
Pin No.
Pin Name
P8
I/O
Function
Parallel data input 8
Output 6
1
2
I
O
O
I
Q6
3
Q8
Output 8
4
P4
Parallel data input 4
Parallel data input 3
Parallel data input 2
Parallel data input 1
Ground
5
P3
I
6
P2
I
7
P1
I
8
VSS
P/S
CLOCK
DS
―
I
9
Parallel/serial input selection
Clock input
10
11
12
13
14
15
16
I
I
Serial data input
Output 7
Q7
O
I
P5
Parallel data input 5
Parallel data input 6
Parallel data input 7
Power supply
P6
I
P7
I
VDD
―
Absolute Maximum Ratings
Parameter
Supply Voltage
Symbol
VDD
VIN
Rating
Unit
V
-0.3 to +18.0
-0.3 to (VDD+0.3)
±10
Input Voltage
V
Input Current
IIN
mA
°C
°C
°C
W
Operating Temperature
Storage Temperature
Maximum Junction Temperature
Power Dissipation
Topr
Tstg
-40 to +85
-55 to +150
+150
TJmax
PD
0.56 (Note 1)
(Note 1) Mounted on 70mm x 70mm x 1.6mm glass epoxy board. Reduce 4.5mW per 1°C above 25°C.
Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated
over the absolute maximum ratings
Recommended Operating Conditions
Parameter
Supply Voltage
Input Voltage
Symbol
VDD
Rating
+3.0 to +16.0
0 to VDD
Unit
V
VIN
V
www.rohm.com
TSZ02201-0RDR1GZ00230-1-2
04.Sep.2013 Rev.001
© 2013 ROHM Co., Ltd. All rights reserved.
3/13
TSZ22111・15・001
Daattaasshheeeett
BU4021BF
Electrical Characteristics
(Unless otherwise specified, VSS=0V, TA =25°C)
Limits
Typ
Figure
No.
Unit
V
Parameter
Symbol
Conditions
-
Min
3.5
7.0
11.0
-
-
-
-
-
4.95
9.95
14.95
-
-
-
-0.16
-0.4
-1.2
0.44
1.1
3.0
-
Max
-
-
-
1.5
3.0
4.0
0.3
-0.3
-
VDD (V)
5
10
15
5
10
15
15
15
5
10
15
5
10
15
5
10
15
5
10
15
5
10
15
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Input “H” voltage
VIH
-
-
Input “L” voltage
VIL
V
-
-
-
Input “H” current
Input “L” current
IIH
IIL
µA
µA
VIH=15V
VIL=0V
-
-
Output “H” voltage
Output “L” voltage
Output “H” current
Output “L” current
Quiescent supply current
VOH
VOL
IOH
IOL
V
IO=0mA
1
2
1
2
-
0.05
0.05
0.05
-
-
-
-
-
-
V
IO=0mA
VO=4.6V
VO=9.5 V
VO=13.5 V
VO=0.4 V
VO=0.5 V
VO=1.5 V
mA
mA
µA
20
40
80
IDD
-
-
VI=VDD or 0V
(Unless otherwise specified VSS=0V, TA =25°C, CL=50pF）
Limits
Figure
No.
Unit
ns
Parameter
Symbol
Conditions
-
Min
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Typ
180
90
Max
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
V
DD (V)
5
10
15
5
10
15
5
10
15
5
10
15
5
10
15
5
10
15
5
10
15
5
Output rising time
tTLH
-
65
100
50
40
Output falling time
tTHL
ns
ns
-
-
-
-
-
-
-
-
400
170
115
Propagation delay time
L to H
tPLH
3・5
400
170
115
Propagation delay time
H to L
tPHL
ns
4・6
150
50
30
Set up time
tSU
ns
7
9
-
-
-
-
-
-
-
150
75
40
Minimum clock pulse width
Maximum clock frequency
tW(CLK)
f (CLK)
ns
3.0
6.0
8.0
-
-
-
150
75
40
5
MHz
µs
15
5.0
4.0
-
-
-
tR(CLK)
tF(CLK)
Maximum clock rising time
Maximum clock falling time
10
15
5
10
15
-
-
Minimum P/S pulse width
Input capacitance
tW(P/S)
CIN
ns
-
-
10
-
pF
-
www.rohm.com
TSZ02201-0RDR1GZ00230-1-2
04.Sep.2013 Rev.001
© 2013 ROHM Co., Ltd. All rights reserved.
4/13
TSZ22111・15・001
Daattaasshheeeett
BU4021BF
Test Circuits
VDD
DC Characteristics
1.
+
A
IDD
VOH
+
IO
VOL
V
P8
Q6
Q8
P4
1
2
3
4
5
6
7
8
16
VDD
P7 15
P6 14
P5 13
P3
Q7 12
IIH IIL
A
P2
DS 11
+
A
IOH IOL
VO
+
P1
CLOCK 10
P/S 9
VIH VIL
VSS
VDD
Switching Characteristics
2.
OUTPUT
Q8
Q7
Q6
P8
Q6
Q8
P4
1
2
3
4
5
6
7
8
16
VDD
INPUT
P7 15
P6 14
CL=50pF
CL=50pF
P5 13
P3
Q7 12
P2
DS 11
CL=50pF
P1
CLOCK 10
P/S 9
VSS
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0RDR1GZ00230-1-2
04.Sep.2013 Rev.001
5/13
Daattaasshheeeett
BU4021BF
Waveforms of Switching Characteristics
20ns
20ns
VDD
Parallel Data
or
Serial Data
90%
50%
10%
VSS
VDD
th
tW
90%
50%
tr
tf
tsu
10%
tPLH
CLOCK
or
P/S
VSS
VOH
tPHL
90%
50%
10%
OUTPUT
Qn
VOL
tTLH
tTHL
www.rohm.com
TSZ02201-0RDR1GZ00230-1-2
04.Sep.2013 Rev.001
© 2013 ROHM Co., Ltd. All rights reserved.
6/13
TSZ22111・15・001
Daattaasshheeeett
BU4021BF
Typical Performance Curves
50
40
30
20
10
0
0
V
DD=5V
85℃
25℃
-40℃
-10
-20
-30
-40
-50
VDD=10V
85℃
25℃
VDD=15V
-40°C
-40℃
25°C
85°C
VDD=10V
-40°C
VDD=15V
85℃
25℃
-40℃
25°C
85°C
VDD=5V
-40°C
25°C
85°C
0
5
10
15
20
0
5
10
15
20
Output Voltage [V]
Output Voltage [V]
Figure 1.
Figure 2.
Output “H” Current vs Output Voltage
Output “L” Current vs Output Voltage
800
700
600
500
400
300
200
100
0
800
700
600
500
400
300
200
100
0
VDD=3V
VDD=3V
Operating Temperature Range
VDD=5V
Operating Temperature Range
VDD=5V
VDD=10V
VDD=10V
VDD=16V
VDD=16V
-50
-25
0
25
50
75
100
-50
-25
0
25
50
75
100
Ambient Temperature [°C]
Ambient Temperature [
]
℃
Figure 3.
Figure 4.
Propagation Delay Time :tPLH (CLOCK – Qn)
Propagation Delay Time :tPHL (CLOCK – Qn)
(*)The above characteristics are measurements of typical sample, they are not guaranteed.
www.rohm.com
TSZ02201-0RDR1GZ00230-1-2
04.Sep.2013 Rev.001
© 2013 ROHM Co., Ltd. All rights reserved.
7/13
TSZ22111・15・001
Daattaasshheeeett
BU4021BF
Typical Performance Curves - continued
800
700
800
700
600
500
400
300
200
100
0
VDD=3V
VDD=3V
600
500
400
300
200
100
0
Operating Temperature Range
Operating Temperature Range
VDD=5V
VDD=5V
VDD=10V
VDD=10V
VDD=16V
VDD=16V
-50
-25
0
25
50
75
100
-50
-25
0
25
50
75
100
Ambient Temperature [°C]
Ambient Temperature [°C]
Figure 6.
Figure 5.
Propagation Delay Time :tPHL (P/S – Qn)
Propagation Delay Time :tPLH (P/S – Qn)
200
180
160
140
120
100
80
200
175
150
125
100
75
Operating Temperature Range
Operating Temperature Range
VDD=3V
VDD=3V
VDD=5V
60
VDD=5V
50
VDD=10V
VDD=16V
40
V
DD=10V
25
20
VDD=16V
0
0
-50
-25
0
25
50
75
100
-50
-25
0
25
50
75
100
Ambient Temperature [°C]
Ambient Temperature [°C]
Figure 7.
Figure 8.
Setup Time :tsu (DATA – CLOCK)
Hold Time :th (CLOCK – DATA)
(*)The above characteristics are measurements of typical sample, they are not guaranteed.
www.rohm.com
TSZ02201-0RDR1GZ00230-1-2
04.Sep.2013 Rev.001
© 2013 ROHM Co., Ltd. All rights reserved.
8/13
TSZ22111・15・001
Daattaasshheeeett
BU4021BF
Typical Performance Curves - continued
200
180
160
140
120
100
80
200
180
VDD=3V
VDD=3V
160
140
Operating Temperature Range
Operating Temperature Range
120
100
VDD=5V
VDD=5V
80
60
40
20
0
60
VDD=10V
DD=16V
VDD=10V
40
V
VDD=16V
20
0
-50
-25
0
25
50
75
100
-50
-25
0
25
50
75
100
Ambient Temperature [°C]
Ambient Temperature [°C]
Figure 10.
Figure 9.
Minimum P/S Pulse Width
Minimum CLOCK Pulse Width
(*)The above characteristics are measurements of typical sample, they are not guaranteed.
Power Dissipation
Power dissipation(total loss) indicates the power that can be consumed by IC at TA=25°C(normal temperature). IC is heated
when it consumed power, and the temperature of IC chip becomes higher than ambient temperature. The temperature that
can be accepted by IC chip depends on circuit configuration, manufacturing process, and consumable power is limited.
Power dissipation is determined by the temperature allowed in IC chip(maximum junction temperature) and thermal
resistance of package(heat dissipation capability). The maximum junction temperature is typically equal to the maximum
value in the storage temperature range. Heat generated by consumed power of IC radiates from the mold resin or lead
frame of the package. The parameter which indicates this heat dissipation capability(hardness of heat release)is called
thermal resistance, represented by the symbol θJA (°C/W).The temperature of IC inside the package can be estimated by
this thermal resistance. Figure 11 shows the model of thermal resistance of the package. Thermal resistance θJA, ambient
temperature TA, maximum junction temperature TJmax, and power dissipation PD can be calculated by the equation below:
θJA = (TJmax - TA) / PD
(°C/W)
Derating curve in Figure 12 indicates power that can be consumed by IC with reference to ambient temperature. Power that
can be consumed by IC with reference to ambient temperature. Power that can be consumed by IC begins to attenuate at
certain ambient temperature. This gradient is determined by thermal resistance θJA. Thermal resistance θJA depends on
chip size, power consumption, package, ambient temperature, package condition, wind velocity, etc even when the same of
package is used. Thermal reduction curve indicates a reference value measured at a specified condition.
1.0
0.8
0.6
0.4
θJA =( TJmax - TA)/ PD (°C/W)
Ambient temperature TA (℃)
BU4021BF (SOP16)
0.2
0.0
Chip surface temperature TJ(℃)
85
0
25
50
75
100
125
150
Power dissipation PD (W)
Ambient Temperature [
]
℃
Figure 11. Thermal resistance
Figure 12. Derating Curve
www.rohm.com
TSZ02201-0RDR1GZ00230-1-2
04.Sep.2013 Rev.001
© 2013 ROHM Co., Ltd. All rights reserved.
9/13
TSZ22111・15・001
Daattaasshheeeett
BU4021BF
I/O Equivalence Circuit
Input Terminal
Output Terminal
2,3,12
Pin No.
1,4,5,6,7,9,10,11,13,14,15
VDD
VDD
VDD
VDD
Equivalence
Circuit
VSS
VSS
VSS
VSS
Operational Notes
1. Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply
pins.
2. Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the
digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog
block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and
aging on the capacitance value when using electrolytic capacitors.
3. Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
4. Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
5. Thermal Consideration
Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in
deterioration of the properties of the chip. The absolute maximum rating of the PD stated in this specification is when
the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating,
increase the board size and copper area to prevent exceeding the PD rating.
6. Recommended Operating Conditions
These conditions represent a range within which the expected characteristics of the IC can be approximately obtained.
The electrical characteristics are guaranteed under the conditions of each parameter.
7. Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow
instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply.
Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing
of connections.
8. Operation Under Strong Electromagnetic Field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
www.rohm.com
TSZ02201-0RDR1GZ00230-1-2
04.Sep.2013 Rev.001
© 2013 ROHM Co., Ltd. All rights reserved.
10/13
TSZ22111・15・001
Daattaasshheeeett
BU4021BF
Operational Notes - continued
9. Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject
the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should
always be turned off completely before connecting or removing it from the test setup during the inspection process. To
prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and
storage.
10. Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and
unintentional solder bridge deposited in between pins during assembly to name a few.
11. Unused Input Pins
Input terminals of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance
and extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small
charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and
cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the
power supply or ground line.
12. Regarding the Input Pin of the IC
In the construction of this IC, P-N junctions are inevitably formed creating parasitic diodes or transistors. The operation
of these parasitic elements can result in mutual interference among circuits, operational faults, or physical damage.
Therefore, conditions which cause these parasitic elements to operate, such as applying a voltage to an input pin lower
than the ground voltage should be avoided. Furthermore, do not apply a voltage to the input terminals when no power
supply voltage is applied to the IC. Even if the power supply voltage is applied, make sure that the input pins have
voltages within the values specified in the electrical characteristics of this IC.
13. Ceramic Capacitor
When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with
temperature and the decrease in nominal capacitance due to DC bias and others.
Ordering Information
B
U
4
0
2
1
B
F
-
E 2
Package
Part Number
Packaging and forming specification
E2 : Embossed tape and reel
F
: SOP16
Marking Diagram
SOP16(TOP VIEW)
Part Number Marking
LOT Number
BU4021 BF
1PIN MARK
www.rohm.com
TSZ02201-0RDR1GZ00230-1-2
04.Sep.2013 Rev.001
© 2013 ROHM Co., Ltd. All rights reserved.
11/13
TSZ22111・15・001
Daattaasshheeeett
BU4021BF
Physical Dimension, Tape and Reel Information – continued
Package Name
SOP16
(Max 10.35 (include.BURR))
(UNIT : mm)
PKG : SOP16
Drawing No. : EX114-5001
<Tape and Reel information>
Tape
Embossed carrier tape
2500pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
TSZ02201-0RDR1GZ00230-1-2
04.Sep.2013 Rev.001
© 2013 ROHM Co., Ltd. All rights reserved.
12/13
TSZ22111・15・001
Daattaasshheeeett
BU4021BF
Revision History
Date
Revision
001
Changes
New Release
04.Sep.2013
www.rohm.com
TSZ02201-0RDR1GZ00230-1-2
04.Sep.2013 Rev.001
© 2013 ROHM Co., Ltd. All rights reserved.
13/13
TSZ22111・15・001
Daattaasshheeeett
Notice
Precaution on using ROHM Products
1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice - GE
Rev.002
© 2014 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice - GE
Rev.002
© 2014 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2014 ROHM Co., Ltd. All rights reserved.
相关型号：
BU4021BFT1
4000/14000/40000 SERIES, 8-BIT RIGHT PARALLEL IN SERIAL OUT SHIFT REGISTER, TRUE OUTPUT, PDSO16, SOP-16
ROHM
BU4021BFT2
4000/14000/40000 SERIES, 8-BIT RIGHT PARALLEL IN SERIAL OUT SHIFT REGISTER, TRUE OUTPUT, PDSO16, SOP-16
ROHM
©2020 ICPDF网 联系我们和版权申明