BU18JA2VG-C [ROHM]
BU18JA2VG-C是输出为200mA的高性能CMOS稳压器。封装组件采用SSOP5,有利于整机小型化。电路电流33μA,低功耗且噪音特性、负载响应特性优异,适用于车载摄像头、车载雷达等各种用途。;型号: | BU18JA2VG-C |
厂家: | ROHM |
描述: | BU18JA2VG-C是输出为200mA的高性能CMOS稳压器。封装组件采用SSOP5,有利于整机小型化。电路电流33μA,低功耗且噪音特性、负载响应特性优异,适用于车载摄像头、车载雷达等各种用途。 雷达 稳压器 |
文件: | 总30页 (文件大小:2396K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Datasheet
CMOS LDO Regulators for Automotive
1ch 200mA
CMOS LDO Regulators
BUxxJA2VG-C series
General Description
Key Specifications
BUxxJA2VG-C series are high-performance CMOS LDO
regulators with output current ability of up to 200mA. The
SSOP5 package can contribute to the downsizing of the set.
These devices have excellent noise and load response
characteristics despite of its low circuit current consumption
of 33µA. They are most appropriate for various applications
such as power supplies for radar modules and camera
modules.
Input Power Supply Voltage Range:
Output Current Range:
Operating Temperature Range:
Output Voltage Lineup:
Output Voltage Accuracy:
Circuit Current:
1.7V to 6.0V
0 to 200mA
-40°C to +125°C
1.0V to 3.3V
±2.0%
33µA(Typ)
0μA (Typ)
Standby Current:
Package
SSOP5
W(Typ) x D(Typ) x H(Max)
2.90mm x 2.80mm x 1.25mm
Features
AEC-Q100 qualified(Note 1)
High Output Voltage Accuracy: 2.0%
(In all recommended conditions)
High Ripple Rejection: 68 dB (Typ, 1kHz)
Compatible with small ceramic capacitor
(Cin=Cout=0.47µF)
Low Current Consumption: 33µA
Output Voltage ON/OFF control
Built-in Over Current Protection Circuit (OCP)
Built-in Thermal Shutdown Circuit (TSD)
Package SSOP5 is similar to SOT23-5(JEDEC)
(Note 1) Grade1
Applications
Automotive Radar modules
Automotive Camera modules
Typical Application Circuit
Vin
VOUT
VIN
Vout
Cin
On
Cout
BUxxJA2VG-C
GND
STBY
Off
Figure 1. Typical Application Circuit
○Product structure:Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays
.www.rohm.com
TSZ02201-0G5G0A300040-1-2
30.Aug.2017 Rev.004
© 2014 ROHM Co., Ltd. All rights reserved.
1/27
TSZ22111・14・001
BUxxJA2VG-C series
Ordering Information
B
U
X
X
J
A
2
V
G
-
C
G
Y
Y
Part
Number
Output Voltage
10 : 1.0V
12 : 1.2V
1C : 1.25V
15 : 1.5V
18 : 1.8V
25 : 2.5V
28 : 2.8V
2J : 2.85V
30 : 3.0V
33 : 3.3V
Series name
Package
G : SSOP5
Product Rank
C :for Automotive
Manufacturing
Code
Packageing and forming specification
Embossed tape and reel
Maximum Output Current : 200mA
Maximum Power Supply Voltage Range : 6.5V
High-speed load response, Low noise, Shutdown SW
TR : The pin number 1 is the upper right
TL (Note 1) : The pin number 1 is the lower left
(Note 1) Only xx=18 and 33 models support TL version.
Pin Description(Note 2)
Pin No.
Symbol
VIN
Function
N.C.
VOUT
1
2
3
4
5
Input Pin
GND Pin
GND
STBY
N.C.
Output Control Pin
(High:ON, Low:OFF)
No Connect
STBY
VIGND
VOUT
Output Pin
(Note 2) N.C. Pin can be open because it isn’t connecting it inside of IC.
Block Diagram
1
VIN
STBY
3
STBY
VREF
-
+
AMP
5
OCP
VOUT
TSD
N.C.
4
2
GND
Figure 2. Block diagram
Block
Function
Description
STBY
VREF
AMP
Control Standby mode
Internal Reference Voltage
Error AMP
STBY controls internal block active and standby state
VREF generates reference voltage.
AMP amplifies electric signal and drives output power transistor.
When output current exceeds current ability, OCP restricts Output
Current.
OCP
TSD
Over Current Protection
Thermal Shutdown
When Junction temperature rise and exceed Maximum junction
temperature, TSD turns off Output power transistor.
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
2/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Absolute Maximum Ratings
Parameter
Symbol
VIN
Rating
Unit
V
-0.3 to +6.5(Note1)
-0.3 to +6.5
+150
Power Supply Voltage Range
STBY Voltage
VSTBY
Tjmax
Topr
V
Junction Temperature
°C
°C
°C
Operating Temperature Range
-40 to +125
-55 to +150
Storage Temperature Range
Tstg
(Note 1) Not to exceed Tjmax
Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is
operated over the absolute maximum ratings.
Recommended Operating Ratings(Ta=-40°C to +125°C)
Parameter
Power Supply Voltage Range
STBY voltage
Symbol
VIN
Limit
1.7 to 6.0
1.7 to 6.0
200
Unit
V
VSTBY
IOUTMAX
V
Maximum Output Current
mA
Recommended Operating Conditions
Rating
Typ
Parameter
Symbol
Cin
Unit
Conditions
Min
Max
Input capacitor
0.47(Note2) 1.0
-
µF
µF
A ceramic capacitor is recommended.
A ceramic capacitor is recommended.
Output capacitor
Cout 0.47(Note2) 1.0
-
(Note 2) Set the value of the capacitor so that it does not fall below the minimum value.
Take into consideration the temperature characteristics, DC device characteristics and degradation with time.
Thermal Resistance (Note 3)
Thermal Resistance (Typ)
Parameter
Symbol
Unit
1s(Note 5)
2s2p(Note 6)
SSOP5
Junction to Ambient
Junction to Top Characterization Parameter(Note 4)
θJA
376.5
40
185.4
30
°C/W
°C/W
ΨJT
(Note 3)Based on JESD51-2A(Still-Air).
(Note 4)The thermal characterization parameter to report the difference between junction temperature and the temperature at the top center of the outside
surface of the component package.
(Note 5)Using a PCB board based on JESD51-3.
Layer Number of
Measurement Board
Material
Board Size
Single
FR-4
114.3mm x 76.2mm x 1.57mmt
Top
Copper Pattern
Thickness
70μm
Footprints and Traces
(Note 6)Using a PCB board based on JESD51-7.
Layer Number of
Material
Board Size
114.3mm x 76.2mm x 1.6mmt
2 Internal Layers
Measurement Board
4 Layers
FR-4
Top
Bottom
Copper Pattern
74.2mm x 74.2mm
Copper Pattern
Thickness
70μm
Copper Pattern
Thickness
35μm
Thickness
70μm
Footprints and Traces
74.2mm x 74.2mm
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
3/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Electrical Characteristics
(Unless otherwise noted, Ta=-40 to 125°C, VIN=VOUT+1.0V(Note 1), VSTBY=1.5V, Cin=1μF, Cout=1μF.
The Typical value is defined at Ta=25°C)
Limit
Parameter
Symbol
Unit
V
Conditions
IOUT=0 to 200mA
VOUT>2.5V, VIN=VOUT+0.5 to 6.0V
VOUT≦2.5V, VIN=3.0 to 6.0V
IOUT=10mA
VOUT≦2.5V, VIN=3.0 to 6.0V
IOUT=10mA
VOUT>2.5V, VIN=VOUT+0.5 to 6.0V
MIN
TYP
MAX
VOUT
×0.98
VOUT
×1.02
Output Voltage
VOUT
VOUT
-
-
4
6
15
20
mV
mV
Line Regulation
VDLI
Load Regulation1
Load Regulation2
VDLO1
VDLO2
-
0.5
1
5
10
315
190
155
-
mV
mV
mV
mV
mV
mA
mA
mA
µA
IOUT=1 to 100mA
-
IOUT=1 to 200mA
-
160
100
85
-
VOUT=1.8V, IOUT=100mA
VOUT=2.5V, IOUT=100mA
VOUT≧2.8V, IOUT=100mA
VIN=VOUT+1.0V (Note 1)
applied VOUT×0.98 for VOUT Pin, Ta=25°C
VOUT=0V, Ta=25°C
Dropout Voltage
VDROP
-
-
Maximum Output Current
Limit Current
IOUTMAX
ILMAX
200
250
400
100
33
-
-
Short Current
ISHORT
IGND
-
-
-
200
80
2.0
Circuit Current
IOUT=0mA
Circuit Current (STBY)
ICCST
µA
VSTBY=0V
VRR=-20dBv, fRR=1kHz
IOUT=10mA, Ta=25°C
IOUT=1 to 150mA, Trise=Tfall=1µs
VIN=VOUT+1.0V, Ta=25°C
VIN=VOUT+0.5 to VOUT+1.0V
Trise=Tfall =10µs, Ta=25°C
Ripple Rejection Ratio
R.R.
-
-
68
-
-
dB
mV
mV
Load Transient Response
VLOT
±65
Line Transient Response
Output Noise Voltage
Startup Time
VLIT
VNOISE
TST
-
-
-
±5
30
-
-
µVrms Bandwidth 10 to 100kHz, Ta=25°C
Output Voltage settled
100
300
µs
within tolerances (Note 2), Ta=25°C
ON
VSTBH
VSTBL
ISTBY
1.1
-0.2
-
-
-
-
VIN
0.5
4.0
V
STBY Control
Voltage
OFF
V
Ta=25°C
STBY Pin Current
µA
(Note 1) VIN=3.0V for VOUT<2.5V.
(Note 2) Startup time=time from EN assertion to VOUT×0.98
www.rohm.com
TSZ02201-0G5G0A300040-1-2
30.Aug.2017 Rev.004
© 2014 ROHM Co., Ltd. All rights reserved.
4/27
TSZ22111・15・001
BUxxJA2VG-C series
Reference data BU18JA2VG-C (Unless otherwise specified, Ta=25°C)
1.83
1.82
1.81
1.80
1.79
1.78
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
IOUT=0mA
IOUT=50mA
IOUT=200mA
IOUT=0mA
IOUT=50mA
IOUT=200mA
Ta=25°C
VIN=VSTBY
Ta=25°C
VIN=VSTBY
0.0
1.0
2.0
3.0
4.0
5.0
6.0
3.0
4.0
5.0
6.0
Input Voltage VIN (V)
Input Voltage VIN (V)
Figure 3. Output Voltage vs Input Voltage
Figure 4. Line Regulation
60
1.85
Ta=125℃
1.84
1.83
1.82
1.81
1.80
1.79
1.78
1.77
1.76
1.75
50
40
30
20
10
0
Ta=25℃
Ta=125℃
Ta=25℃
Ta=-40℃
Ta=-40℃
VIN=VSTBY
IOUT=0mA
VIN=3.5V
VSTBY=1.5V
0
50
100
150
200
0.0
1.0
2.0
3.0
4.0
5.0
6.0
Output Current IOUT (mA)
Input Voltage VIN (V)
Figure 5. Circuit Current vs Input Voltage
Figure 6. Load Regulation
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
5/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Reference data BU18JA2VG-C (Unless otherwise specified, Ta=25°C)
120
100
80
60
40
20
0
2.00
1.80
1.60
1.40
1.20
1.00
0.80
0.60
0.40
0.20
0.00
Ta=125℃
Ta=25℃
Ta=-40℃
VIN=6.0V
VIN=3.5V
VIN=3.0V
VIN=3.5V
VSTBY=1.5V
Ta=25°C
VSTBY=1.5V
0
50
100
150
200
0
100
200
300
400
500
Output Current IOUT (mA)
Output Current IOUT (mA)
Figure 7. Circuit Current vs Output Current
Figure 8. OCP Threshold
100
1.85
1.84
1.83
1.82
1.81
1.80
1.79
1.78
1.77
1.76
1.75
90
80
70
60
50
40
30
20
10
0
VIN=3.5V
VSTBY=1.5V
IOUT=0.1mA
VIN=3.5V
VSTBY=1.5V
IOUT=0.1mA
-40 -20
0
20 40 60 80 100 120
-40 -20
0
20 40 60 80 100 120
Temperature Ta (°C)
Temperature Ta (°C)
Figure 9. Output Voltage vs Temperature
Figure 10. Circuit Current vs Temperature
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
6/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Reference data BU18JA2VG-C (Unless otherwise specified, Ta=25°C)
100
90
80
70
60
50
40
30
20
10
0
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
Ta=125℃
Ta=-40℃
Ta=25℃
VIN=3.5V
IOUT=0.1mA
VIN=6.0V
VSTBY=0V
0.00
0.25
0.50
STBY Pin Voltage VSTBY(V)
Figure 11. STBY Threshold
0.75
1.00
1.25
1.50
-40 -25 -10 5 20 35 50 65 80 95 110 125
Temperature Ta (°C)
Figure 12. Circuit Current at STBY vs Temperature
450
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
400
350
300
250
200
150
100
50
VIN=0.98×VOUT
VSTBY=1.5V
Ta=125℃
Ta=25℃
Ta=-40℃
Ta=125℃
Ta=25℃
Ta=-40℃
0
0.0
1.0
2.0
STBY Pin Voltage VSTBY (V)
Figure 13. STBY Pin Current vs STBY Pin Voltage
3.0
4.0
5.0
6.0
0
50
100
150
200
Output Current IOUT(mA)
Figure 14. Dropout Voltage vs Output Current
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0G5G0A300040-1-2
7/27
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Reference data BU18JA2VG-C (Unless otherwise specified, Ta=25°C)
100
90
80
70
60
50
40
30
20
10
0
50
45
40
35
30
25
20
15
10
5
Ta=25°C
VIN=3.5V
VRR=-20dBv
VSTBY=1.5V
IOUT=10mA
Cin=Cout=1μF
Ta=25°C
VIN=3.5V
VSTBY=1.5V
Cin=Cout=1μF
Bandwidth 10 to 100kHz
0
100
1000
10000
100000
0
50
100
150
200
Frequency (Hz)
Output Current IOUT (mA)
Figure 15. Ripple Rejection Ratio vs Frequency
Figure 16. Output Noise Voltage vs Output Current
10
1
0.1
0.01
Ta=25°C
VIN=3.5V
VSTBY=1.5V
IOUT=10mA
Cin=Cout=1μF
10
100
1000
10000
100000
Frequency (Hz)
Figure 17.Output Noise Density vs Frequency
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0G5G0A300040-1-2
8/27
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Reference data BU18JA2VG-C (Unless otherwise specified, Ta=25°C)
Trise Tfall=1µs,
Cin=Cout=1µF
VIN=3.5V VSTBY=1.5V
VIN=3.5V VSTBY=1.5V
=
Trise Tfall=1µs,
Cin=Cout=1µF
=
200
100
0
200
100
0
150mA
100mA
IOUT
1mA
IOUT
100mA/div
1mA
100mA/div
20µs/div
20µs/div
1.90
1.80
1.70
1.90
1.80
1.70
VOUT
VOUT
100mV/div
100mV/div
Figure 18. Load Response
(1mA to 100mA)
Figure 19. Load Response
(1mA to 150mA)
VIN=VSTBY
6.0V
6.0
4.0
2.0
0.0
6.0
4.0
2.0
0.0
2.0V/div
VIN=VSTBY 3.5V
3.0V
2.0V/div
Slew Rate 1V/µs
3.0V
Slew Rate 1V/µs
=
=
1ms/div
1ms/div
1.82
1.80
1.78
1.82
1.80
1.78
20mV/div
VOUT
20mV/div
VOUT
Cout=1.0µF
IOUT=10mA
Cout=1.0µF
IOUT=10mA
Figure 20. Line Transient Response
(3.0 to 3.5V)
Figure 21. Line Transient Response
(3.0 to 6.0V)
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
9/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Reference data BU18JA2VG-C (Unless otherwise specified, Ta=25°C)
2.0
1.0
0.0
2.0
1.0
0.0
1.0V/div
1.5V
1.0V/div
1.5V
VSTBY
0V
VSTBY
0V
20µs/div
1.0V/div
20µs/div
1.0V/div
2.0
1.0
0.0
2.0
1.0
0.0
Cout=0.47µF
Cout=1.0µF
Cout=2.2µF
Cout=0.47µF
Cout=1.0µF
Cout=2.2µF
VOUT
VOUT
VIN=3.5V
VIN=3.5V
Figure 22. Startup Time
(ROUT=open)
Figure 23. Startup Time
(ROUT=9Ω)
2.0
1.0
2.0
1.5V
1.5V
VSTBY
VSTBY
1.0
0.0
1.0V/div
1.0V/div
20µs/div
0.0
0V
0V
400ms/div
VOUT
2.0
1.0
0.0
2.0
1.0
0.0
Cout=0.47µF
Cout=1.0µF
Cout=2.2µF
Cout=0.47µF
Cout=1.0µF
Cout=2.2µF
VOUT
1.0V/div
1.0V/div
VIN=3.5V
VIN=3.5V
Figure 24. Discharge Time
(ROUT=open)
Figure 25. Discharge Time
(ROUT=9Ω)
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
10/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Reference data BU33JA2VG-C (Unless otherwise specified, Ta=25°C)
3.35
3.33
3.31
3.29
3.27
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
IOUT=0mA
IOUT=50mA
IOUT=200mA
IOUT=0mA
IOUT=50mA
IOUT=200mA
Ta=25°C
VIN=VSTBY
Ta=25°C
VIN=VSTBY
3.8
4.3
4.8
5.3
5.8
0.0
1.0
2.0
3.0
4.0
5.0
6.0
Inout Voltage VIN (V)
Input Voltage VIN (V)
Figure 26. Output Voltage vs Input Voltage
Figure 27. Line Regulation
60
50
40
30
20
10
0
3.35
3.34
3.33
3.32
3.31
3.30
3.29
3.28
3.27
3.26
3.25
Ta=125℃
Ta=25℃
Ta=-40℃
Ta=125℃
Ta=25℃
Ta=-40℃
VIN=VSTBY
IOUT=0mA
VIN=4.3V
VSTBY=1.5V
0.0
1.0
2.0
3.0
4.0
5.0
6.0
0
50
100
150
200
Input Voltage VIN (V)
Output Current IOUT(mA)
Figure 28. Circuit Current vs Input Voltage
Figure 29. Load Regulation
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
11/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Reference data BU33JA2VG-C (Unless otherwise specified, Ta=25°C)
100
90
80
70
60
50
40
30
20
10
0
3.50
3.00
2.50
2.00
1.50
1.00
0.50
0.00
Ta=125℃
Ta=25℃
Ta=-40℃
VIN=3.8V
VIN=4.3V
VIN=6.0V
VIN=4.3V
VSTBY=1.5V
0
100
200
300
400
500
0
50
100
150
200
Output Current IOUT(mA)
Output Current IOUT(mA)
Figure 31. OCP Threshold
Figure 30. Circuit Current vs Output Current
3.35
3.34
3.33
3.32
3.31
3.30
3.29
3.28
3.27
3.26
3.25
100
90
80
70
60
50
40
30
20
10
0
VIN=4.3V
VSTBY=1.5V
IOUT=0.1mA
VIN=4.3V
VSTBY=1.5V
IOUT=0.1mA
-40 -20
0
20
Temperature Ta (°C)
Figure 32. Output Voltage vs Temperature
40
60
80 100 120
-40 -20
0
20
40
60
80 100 120
Temperature Ta (°C)
Figure 33. Circuit Current vs Temperature
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
12/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Reference data BU33JA2VG-C (Unless otherwise specified, Ta=25°C)
200
180
160
140
120
100
80
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
Ta=125℃
Ta=-40℃
Ta=25℃
60
VIN=6.0V
VSTBY=0V
VIN=4.3V
IOUT=0.1mA
40
20
0
-40 -25 -10
5
20 35 50 65 80 95 110 125
0.00
0.25
0.50
0.75
1.00
1.25
1.50
STBY Pin Voltage VSTBY(V)
Temperature Ta (°C)
Figure 34. STBY Threshold
Figure 35. Circuit Current at STBY vs Temperature
500
2.0
450
400
350
300
250
200
150
100
50
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
Ta=125℃
Ta=25℃
Ta=-40℃
VIN=0.98×VOUT
VSTBY=1.5V
Ta=125℃
Ta=25℃
Ta=-40℃
0
0
50
100
150
200
0.0
1.0
2.0
3.0
4.0
5.0
6.0
STBY Pin Voltage VSTBY (V)
Output Current IOUT(mA)
Figure 36. STBY Pin Current vs STBY Pin Voltage
Figure 37. Dropout Voltage vs Output Current
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0G5G0A300040-1-2
13/27
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Reference data BU33JA2VG-C (Unless otherwise specified, Ta=25°C)
100
90
80
70
60
50
40
30
20
10
0
50
45
40
35
30
25
20
15
10
5
Ta=25°C
VIN=4.3V
VSTBY=1.5V
Cin=Cout=1μF
Bandwidth 10 to 100kHz
Ta=25°C
VIN=4.3V
VRR=-20dBv
VSTBY=1.5V
IOUT=10mA
Cin=Cout=1μF
0
100
1000
10000
100000
0
50
100
150
200
Frequency (Hz)
Output Current IOUT(mA)
Figure 38. Ripple Rejection Ratio vs Frequency
Figure 39. Output Noise Voltage vs Output Current
10
1
0.1
Ta=25°C
VIN=4.3V
VSTBY=1.5V
IOUT=10mA
Cin=Cout=1μF
0.01
10
100
1000
10000
100000
Frequency (Hz)
Figure 40. Output Noise Density vs Frequency
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0G5G0A300040-1-2
14/27
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Reference data BU33JA2VG-C (Unless otherwise specified, Ta=25°C)
VIN=4.3V VSTBY=1.5V
VIN=4.3V VSTBY=1.5V
150mA
Trise Tfall=1µs
Cin=Cout=1µF
Trise Tfall=1µs
Cin=Cout=1µF
=
=
200
100
0
200
100
0
100mA
IOUT
IOUT
100mA/div
1mA
1mA
100mA/div
20µs/div
20µs/div
3.40
3.30
3.20
3.40
3.30
3.20
VOUT
VOUT
100mV/div
100mV/div
Figure 41. Load Response
(1 to 100mA)
Figure 42. Load Response
(1 to 150mA)
2.0V/div
6.0V
VIN=VSTBY
6.0
6.0
4.0
2.0
0.0
VIN=VSTBY
3.8V
4.3V
2.0V/div
4.0
2.0
0.0
Slew Rate 1V/µs
=
Slew Rate 1V/µs
=
3.8V
1ms/div
1ms/div
20mV/div
3.32
3.30
3.28
3.32
3.30
3.28
20mV/div
VOUT
VOUT
IOUT=10mA
Cout=1.0µF
Cout=1.0µF
IOUT=10mA
Figure 43. Line Transient Response
(3.8 to 4.3V)
Figure 44. Line Transient Response
(3.8 to 6.0V)
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
15/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Reference data BU33JA2VG-C (Unless otherwise specified, Ta=25°C)
2.0
1.0
2.0
1.0V/div
1.5V
1.0V/div
1.0
0.0
1.5V
VSTBY
0V
VSTBY
0V
0.0
20µs/div
20µs/div
3.0
2.0
3.0
2.0
1.0V/div
1.0V/div
Cout=0.47µF
Cout=1.0µF
Cout=2.2µF
Cout=0.47µF
Cout=1.0µF
Cout=2.2µF
1.0
0.0
1.0
0.0
VOUT
VOUT
VIN=4.3V
VIN=4.3V
Figure 45. Startup Time
(ROUT=open)
Figure 46. Startup Time
(ROUT=16.5Ω)
2.0
1.0
0.0
2.0
1.5V
1.5V
VSTBY
VSTBY
1.0
0.0
1.0V/div
1.0V/div
0V
0V
3.0
3.0
1.0s/div
1.0V/div
40µs/div
VOUT
VOUT
2.0
1.0
0.0
2.0
1.0
0.0
Cout=0.47µF
Cout=1.0µF
Cout=2.2µF
Cout=0.47 F
Cout=1.0µF
Cout=2.2µF
µ
1.0V/div
=3.5V
VIN
VIN=3.5V
Figure 47. Discharge Time
(ROUT=open)
Figure 48. Discharge Time
(ROUT=16.5Ω)
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
16/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Input/Output Capacitor
It is recommended that a capacitor is placed close to pin between input pin and GND as well as output pin and GND. The
input capacitor becomes more necessary when the power supply impedance is high or when the PCB trace has significant
length. Moreover, the higher the capacitance of the output capacitor the more stable the output will be, even with load and
line voltage variations. However, please check the actual functionality by mounting on a board for the actual application.
Also, ceramic capacitors usually have different thermal and equivalent series resistance characteristics and may degrade
gradually over continued use.
For additional details, please check with the manufacturer and select the best ceramic capacitor for your application.
10
0
Rated Voltage:10V
B1 characteristics
-10
Rated Voltage:10V
B characteristics
-20
-30
Rated Voltage:6.3V
B characteristics
-40
Rated Voltage:4V
X6S characteristics
-50
Rated Voltage:10V
F characteristics
-60
-70
-80
-90
-100
0
1
2
3
4
DC Bias Voltage [V]
Figure 49. Ceramic Capacitor Capacitance Value vs DC Bias Characteristics
(Characteristics Example)
Stable region
Cin=Cout=0.47μFꢀ
Ta=-40°C to 125°C
Equivalent Series Resistance (ESR) of a Ceramic Capacitor
100
10
To prevent oscillation, please attach a capacitor between VOUT
and GND. Capacitors generally have ESR (equivalent series
resistance) and it operates stably in the ESR-IOUT area shown
on the right. Since ceramic capacitors, tantalum capacitors,
electrolytic capacitors, etc. generally have different ESR, please
check the ESR of the capacitor to be used and use it within the
stability area range shown in the right graph for evaluation of the
actual application.
Unstable region
Stable region
1
0.1
0.01
0
50
100
150
200
IOUT[mA]
Figure 50. Stability area characteristics
(VIN=1.7(Note1) to 6.0V)
(Note1) Set VIN voltage considering Dropout Voltage
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
17/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Power Dissipation
■SSOP5
1
IC mounted on ROHM standard board based on JEDEC.
①
: 1-layer PCB
(Copper foil area on the reverse side of PCB: 0 mm × 0 mm)
Board material: FR4
0.8
②0.67 W
Board size: 114.3 mm × 76.2 mm × 1.57 mmt
Mount condition: PCB and exposed pad are soldered.
Top copper foil: ROHM recommended
footprint + wiring to measure, 2 oz. copper.
0.6
0.4
①0.33W
②
: 4-layer PCB
(2 inner layers copper foil area of PCB, copper foil area on the
reverse side of PCB: 74.2 mm × 74.2 mm)
Board material: FR4
Board size: 114.3 mm × 76.2 mm × 1.6 mmt
Mount condition: PCB and exposed pad are soldered.
Top copper foil: ROHM recommended
footprint + wiring to measure, 2 oz. copper.
2 inner layers copper foil area of PCB
: 74.2 mm × 74.2 mm, 1 oz. copper.
0.2
0
0
25
50
75
100
125
150
Ambient Temperature: Ta [°C]
Copper foil area on the reverse side of PCB
: 74.2 mm × 74.2 mm, 2 oz. copper.
Figure 51. SSOP5 Package Data
(Reference Data)
Condition①: θJA = 376.5 °C/W, ΨJT (top center) = 40 °C/W
Condition②: θJA = 185.4 °C/W, ΨJT (top center) = 30 °C/W
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
18/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Thermal Design
Within this IC, the power consumption is decided by the dropout voltage condition, the load current and the circuit current.
Refer to power dissipation curves illustrated in Figure 51 when using the IC in an environment of Ta ≥ 25 °C. Even if the
ambient temperature Ta is at 25 °C, depending on the input voltage and the load current, chip junction temperature can be
very high. Consider the design to be Tj ≤ Tjmax = 150 °C in all possible operating temperature range.
Should by any condition the maximum junction temperature Tjmax = 150 °C rating be exceeded by the temperature increase
of the chip, it may result in deterioration of the properties of the chip. The thermal impedance in this specification is based on
recommended PCB and measurement condition by JEDEC standard. Verify the application and allow sufficient margins in
the thermal design by the following method is used to calculate the junction temperature Tj.
Tj can be calculated by either of the two following methods.
1. The following method is used to calculate the junction temperature Tj.
Tj = Ta + PC × θJA
Where:
Tj
: Junction Temperature
: Ambient Temperature
: Power Consumption
: Thermal Impedance
(Junction to Ambient)
Ta
PC
θJA
2. The following method is also used to calculate the junction temperature Tj.
Tj = TT + PC × ΨJT
Where:
Tj
: Junction Temperature
TT
PC
ΨJT
: Top Center of Case’s (mold) Temperature
: Power consumption
: Thermal Impedance
(Junction to Top Center of Case)
The following method is used to calculate the power consumption Pc (W).
Pc = (VIN - VOUT) × IOUT + VIN × IGND
Where:
PC
VIN
: Power Consumption
: Input Voltage
VOUT
IOUT
IGND
: Output Voltage
: Load Current
: Circuit Current
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
19/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
・Calculation Example (SSOP5)
If VIN = 3.0 V, VOUT = 1.8 V, IOUT = 50 mA, IGND = 33 μA, the power consumption Pc can be calculated as follows:
PC = (VIN - VOUT) × IOUT + VIN × IGND
= (3.0 V – 1.8 V) × 50 mA + 3.0 V × 33 μA
= 0.06 W
At the ambient temperature Tamax = 125°C, the thermal Impedance (Junction to Ambient)θJA = 185.4 °C / W ( 4-layer PCB ),
Tj = Tamax + PC × θJA
= 125 °C + 0.06 W × 185.4 °C / W
= 136.1 °C
When operating the IC, the top center of case’s (mold) temperature TT = 100 °C, ΨJT = 40 °C / W (1-layer PCB),
Tj = TT + PC × ΨJT
= 100 °C + 0.06 W × 40 °C / W
= 102.4 °C
For optimum thermal performance, it is recommended to expand the copper foil area of the board, increasing the layer and
thermal via between thermal land pad.
I/O Equivalence Circuits
5pin (VOUT)
3pin (STBY)
VIN
VIN
VOUT
STBY
Figure 52. Input / Output equivalent circuit
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
20/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Linear Regulators Surge Voltage Protection
The following provides instructions on surge voltage overs absolute maximum ratings polarity protection for ICs.
1. Applying positive surge to the input
If the possibility exists that surges higher than absolute maximum ratings 6.5 V will be applied to the input, a Zener
Diode should be placed to protect the device in between the VIN and the GND as shown in the figure 53.
IN
OUT
VIN
VOUT
COUT
GND
D1
CIN
Figure 53. Surges Higher than 6.5 V will be Applied to the Input
2. Applying negative surge to the input
If the possibility exists that surges lower than absolute maximum ratings -0.3 V will be applied to the input, a Schottky
Diode should be place to protect the device in between the VIN and the GND as shown in the figure 54.
IN
OUT
VIN
VOUT
COUT
GND
D1
CIN
Figure 54. Surges Lower than -0.3 V will be Applied to the Input
Linear Regulators Reverse Voltage Protection
A linear regulator integrated circuit (IC) requires that the input voltage is always higher than the regulated voltage. Output
voltage, however, may become higher than the input voltage under specific situations or circuit configurations, and that
reverse voltage and current may cause damage to the IC. A reverse polarity connection or certain inductor components can
also cause a polarity reversal between the input and output pins. The following provides instructions on reversed voltage
polarity protection for ICs.
1. about Input /Output Voltage Reversal
In an MOS linear regulator, a parasitic element exists as a body diode in the drain-source junction portion of its power
MOSFET. Reverse input/output voltage triggers the current flow from the output to the input through the body diode. The
inverted current may damage or destroy the semiconductor elements of the regulator since the effect of the parasitic
body diode is usually disregarded for the regulator behavior (Figure 55).
IR
VOUT
VIN
Error
AMP.
VREF
Figure 55. Reverse Current Path in an MOS Linear Regulator
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0G5G0A300040-1-2
30.Aug.2017 Rev.004
21/27
BUxxJA2VG-C series
An effective solution to this is an external bypass diode connected in-between the input and output to prevent the
reverse current flow inside the IC (see Figure 56). Note that the bypass diode must be turned on before the internal
circuit of the IC. Bypass diodes in the internal circuits of MOS linear regulators must have low forward voltage VF. Some
ICs are configured with current-limit thresholds to shut down high reverse current even when the output is off, allowing
large leakage current from the diode to flow from the input to the output; therefore, it is necessary to choose one that
has a small reverse current. Specifically, select a diode with a rated peak inverse voltage greater than the input to output
voltage differential and rated forward current greater than the reverse current during use.
D1
IN
OUT
VIN
VOUT
COUT
GND
CIN
Figure 56. Bypass Diode for Reverse Current Diversion
The lower forward voltage (VF) of Schottky barrier diodes cater to requirements of MOS linear regulators, however the
main drawback is found in the level of their reverse current (IR), which is relatively high. So, one with a low reverse
current is recommended when choosing a Schottky diode. The VR-IR characteristics versus temperatures show
increases at higher temperatures.
If VIN is open in a circuit as shown in the following Figure 57 with its input/output voltage being reversed, the only current
that flows in the reverse current path is the bias current of the IC. Because the amperage is too low to damage or
destroy the parasitic element, a reverse current bypass diode is not required for this type of circuit.
ON→OFF
IBIAS
IN
OUT
VOUT
COUT
VIN
GND
CIN
Figure 57. Open VIN
2. Protection against Input Reverse Voltage
Accidental reverse polarity at the input connection flows a large current to the diode for electrostatic breakdown
protection between the input pin of the IC and the GND pin, which may destroy the IC (see Figure 58).
A Schottky barrier diode or rectifier diode connected in series with the power supply as shown in Figure 59 is the
simplest solution to prevent this from happening. The solution, however, is unsuitable for a circuit powered by
batteries because there is a power loss calculated as VF × IOUT, as the forward voltage VF of the diode drops in a
correct connection. The lower VF of a Schottky barrier diode than that of a rectifier diode gives a slightly smaller
power loss. Because diodes generate heat, care must be taken to select a diode that has enough allowance in
power dissipation. A reverse connection allows a negligible reverse current to flow in the diode.
VIN
VOUT
COUT
GND
IN
OUT
D1
-
IN
OUT
VOUT
COUT
VIN
GND
CIN
GND
CIN
+
GND
Figure 58. Current Path in Reverse Input Connection
Figure 59. Protection against Reverse Polarity 1
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
22/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Figure 60 shows a circuit in which a P-channel MOSFET is connected in series with the power. The diode located
in the drain-source junction portion of the MOSFET is a body diode (parasitic element). The voltage drop in a
correct connection is calculated by multiplying the resistance of the MOSFET being turned on by the output
current IOUT, therefore it is smaller than the voltage drop by the diode (see Figure 59) and results in less of a
power loss. No current flows in a reverse connection where the MOSFET remains off.
If the voltage taking account of derating is greater than the voltage rating of MOSFET gate-source junction, lower
the gate-source junction voltage by connecting voltage dividing resistors as shown in Figure 61.
Q1
VIN
Q1
VOUT
COUT
IN
OUT
VIN
VOUT
COUT
IN
OUT
R1
GND
GND
CIN
R2
CIN
Figure 61. Protection against Reverse Polarity 3
Figure 60. Protection against Reverse Polarity 2
3. Protection against Output Reverse Voltage when Output Connect to an Inductor
If the output load is inductive, electrical energy accumulated in the inductive load is released to the ground upon
the output voltage turning off. In-between the IC output and ground pins is a diode for preventing electrostatic
breakdown, in which a large current flows that could destroy the IC. To prevent this from happening, connect a
Schottky barrier diode in parallel with the diode (see Figure 62).
Further, if a long wire is in use for the connection between the output pin of the IC and the load, observe the
waveform on an oscilloscope, since it is possible that the load becomes inductive. An additional diode is needed
for a motor load that is affected by its counter electromotive force, as it produces an electrical current in a similar
way.
VOUT
VIN
OUT
IN
GND
D1
CIN
XLL
COUT
GND
GND
Figure 62. Current Path in Inductive Load (Output: Off)
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0G5G0A300040-1-2
30.Aug.2017 Rev.004
23/27
BUxxJA2VG-C series
Operational Notes
1) Absolute maximum ratings
This product is produced with strict quality control, however it may be destroyed if operated beyond its absolute
maximum ratings. In addition, it is impossible to predict all destructive situations such as short-circuit modes, open
circuit modes, etc. Therefore, it is important to consider circuit protection measures, like adding a fuse, in case the IC is
operated in a special mode exceeding the absolute maximum ratings.
2) GND Potential
GND potential must be the lowest potential of all pins of the IC at all operating conditions. Ensure that no pins are at a
voltage below the ground pin at any time, even during transient condition.
3) Setting of Heat
Carry out the heat design that have adequate margin considering Pd of actual working states.
4) Pin Short and Mistake Fitting
When mounting the IC on the PCB, pay attention to the orientation of the IC. If there is mistake in the placement, the IC
may be burned up.
5) Mutual Impedance
Use short and wide wiring tracks for the power supply and ground to keep the mutual impedance as small as possible.
Use a capacitor to keep ripple to a minimum.
6) STBY Pin Voltage
To enable standby mode for all channels, set the STBY pin to 0.5 V or less, and for normal operation, to 1.1 V or more.
Setting STBY to a voltage between 0.5 and 1.1 V may cause malfunction and should be avoided. Keep transition time
between high and low (or vice versa) to a minimum.
Additionally, if STBY is shorted to VIN, the IC will switch to standby mode and disable the output discharge circuit,
causing a temporary voltage to remain on the output pin. If the IC is switched on again while this voltage is present,
overshoot may occur on the output. Therefore, in applications where these pins are shorted, the output should always
be completely discharged before turning the IC on.
7) Over Current Protection Circuit
Over current and short circuit protection is built-in at the output, and IC destruction is prevented at the time of load short
circuit. These protection circuits are effective in the destructive prevention by sudden accidents, please avoid
applications to where the over current protection circuit operates continuously.
8) Thermal Shutdown
This IC has Thermal Shutdown Circuit (TSD Circuit). When the temperature of IC Chip is higher than 180°C(typ), the
output is turned off by TSD Circuit. TSD Circuit is only designed for protecting IC from thermal over load. Therefore it is
not recommended that you design application where TSD will work in normal condition.
9) Output capacitor
To prevent oscillation at output, it is recommended that the IC be operated at the stable region shown in Figure 50. It
operates at the capacitance of more than 0.47μF. As capacitance is larger, stability becomes more stable and
characteristic of output load fluctuation is also improved.
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
24/27
TSZ22111・15・001
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Marking Diagram
SSOP5(TOP VIEW)
Part Number Marking
Lot Number
Part Number
BU10JA2VG-C
BU12JA2VG-C
BU1CJA2VG-C
BU15JA2VG-C
BU18JA2VG-C
BU25JA2VG-C
BU28JA2VG-C
BU2JJA2VG-C
BU30JA2VG-C
BU33JA2VG-C
Output Voltage [V]
Part Number Marking
1.0
1.2
1.25
1.5
1.8
2.5
2.8
2.85
3.0
3.3
5T
5U
5V
5W
XM
5X
Z6
5Y
5Z
XN
www.rohm.com
TSZ02201-0G5G0A300040-1-2
30.Aug.2017 Rev.004
© 2014 ROHM Co., Ltd. All rights reserved.
25/27
TSZ22111・15・001
BUxxJA2VG-C series
Physical Dimension Tape and Reel Information
Package Name
SSOP5
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0G5G0A300040-1-2
26/27
30.Aug.2017 Rev.004
BUxxJA2VG-C series
Revision History
Date
Revision
Changes
10.Dec.2014
20.Mar.2015
24.Mar.2015
001
002
003
New Release
Thermal Characteristics is changed.
Correction of errors.
Lineup is added
P.2 TL version is added to the “Ordering Information”.
Block Diagram is updated
P.3 The item of the STBY pin is added to “Absolute Maximum Ratings”.
P.7 “Figure 14. Dropout Voltage vs Output Current” is added
P.21 to P.23 The item of “Linear Regulators Surge Voltage Protection” is added
The item of “Linear Regulators Reverse Voltage Protection” is added
P.25 An expression method of “Marking Diagram” is changed
P.26 TL version is added to the “Physical Dimension Tape and Reel Information”.
Others, correction of errors.
30.Aug.2017
004
www.rohm.com
TSZ02201-0G5G0A300040-1-2
© 2014 ROHM Co., Ltd. All rights reserved.
27/27
TSZ22111・15・001
30.Aug.2017 Rev.004
Notice
Precaution on using ROHM Products
(Note 1)
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment
,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PAA-E
Rev.003
© 2015 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PAA-E
Rev.003
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
相关型号:
BU18JA3DG-C (新产品)
BUxxJA3DG-C系列是适用于车载应用的低功耗线性稳压器。该系列IC的耐压为6.5V,输出电流为300mA,消耗电流为37µA(Typ),输出电压精度为±2%,适用于需要低消耗电流的应用。产品具有输出关断功能,当在EN引脚上施加HIGH电压时,IC的输出ON,当施加LOW电压时,IC的输出OFF。另外,本系列IC还内置过电流保护电路,可防止输出短路等导致的IC损坏;内置过热保护电路,可防止IC因过负载状态等导致的热损坏。其输出相位补偿电容可使用低ESR的陶瓷电容器。
ROHM
BU18SD2MG-M
BUxxSD2-M系列为通用型封装SSOP5 (2.90mm x 2.80mm x 1.25mm)中搭载的200mA高性能FULL CMOS稳压器。电路电流33µA,功耗低且噪音特性、负载响应特性优异,适用于汽车音响、汽车导航等各种应用。
ROHM
©2020 ICPDF网 联系我们和版权申明