BR24C02-W [ROHM]
I2C BUS compatible serial EEPROM; I2C总线兼容的串行EEPROM型号: | BR24C02-W |
厂家: | ROHM |
描述: | I2C BUS compatible serial EEPROM |
文件: | 总13页 (文件大小:343K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
BR24C01A-W / BR24C01AF-W / BR24C01AFJ-W / BR24C01AFV-W / BR24C02-W / BR24C02F-W /
BR24C02FJ-W / BR24C02FV-W / BR24C04-W / BR24C04F-W / BR24C04FJ-W / BR24C04FV-W
Memory ICs
I2C BUS compatible serial EEPROM
BR24C01A-W / BR24C01AF-W / BR24C01AFJ-W /
BR24C01AFV-W / BR24C02-W / BR24C02F-W /
BR24C02FJ-W / BR24C02FV-W / BR24C04-W /
BR24C04F-W / BR24C04FJ-W / BR24C04FV-W
The BR24C01A-W, BR24C02-W, and BR24C04-W series are 2-wire (I2C BUS type) serial EEPROMs which are
electrically programmable.
∗I2C BUS is a registered trademark of Philips.
!Applications
VCRs, TVs, printers, car stereos, cordless telephones, short wave radios, programmable DIP switches
!Features
6) Page write function.
1) 128×8bits (1k) serial EEPROM.
(BR24C01A-W / AF-W / AFJ-W / AFV-W)
256×8bits (2k) serial EEPROM.
(BR24C02-W / F-W / FJ-W / FV-W)
512×8bits (4k) serial EEPROM.
(BR24C04-W / F-W / FJ-W / FV-W)
2) Two wire serial interface.
BR24C01A-W / AF-W / AFJ-W / AFV-W : 8 bytes
BR24C02-W / F-W / FJ-W / FV-W : 8 bytes
BR24C04-W / F-W / FJ-W / FV-W : 16 bytes
7) DATA security
Write protect feature
Inhibit to WRITE at low VCC
8) Noise filters at SCL and SDA pins.
9) Address can be incremented automatically during
read operations.
3) Operating voltage range : 2.7V∼5.5V
4) Low current consumption
Active (at 5V) : 1.5mA (Typ.)
10) Compact packages.
Standby (at 5V) : 0.1µA (Typ.)
5) Auto erase and auto complete functions can be used
11) Rewriting possible up to 100,000 times
12) Data can be stored for ten years without corruption.
during write operations.
!Absolute maximum ratings (Ta = 25°C)
Parameter
Symbol
Limits
Unit
V
Applied voltage
V
CC
−0.3~
+6.5
300(SSOP−B8)
450(SOP8, SOP−J8)
800(DIP8)
∗1
∗2
∗3
Power dissipation
Pd
mW
Storage temperature
Operating temperature
Input voltage
Tstg
Topr
−
−65
−40
−0.3
~
+125
°C
°C
V
~
+85
~
V
CC+0.3
∗1 Reduced by 3.0mW for each increase in Ta of 1°C over 25°C.
∗2 Reduced by 4.5mW for each increase in Ta of 1°C over 25°C.
∗3 Reduced by 8.0mW for each increase in Ta of 1°C over 25°C.
BR24C01A-W / BR24C01AF-W / BR24C01AFJ-W / BR24C01AFV-W / BR24C02-W / BR24C02F-W /
BR24C02FJ-W / BR24C02FV-W / BR24C04-W / BR24C04F-W / BR24C04FJ-W / BR24C04FV-W
Memory ICs
!Recommended operating conditions (Ta = 25°C)
Parameter
Power supply voltage
Input voltage
Symbol
Limits
Unit
V
2.7
~
5.5 (WRITE)
V
CC
2.7
~
5.5 (READ)
V
V
IN
0~
VCC
V
!Block diagram
!Pin descriptions
BR24C01A-W / AF-W / AFJ-W / AFV-W
Pin name
Function
A0, A1, A2
SCL
Slave address setting pin
Serial data clock
Serial data input / output
Write protect pin
Power supply
1kbits EEPROM ARRAY
1
2
3
4
8
7
6
5
VCC
A0
A1
A2
∗
8bits
7bits
SDA
WP
SLAVE
·
WORD
ADDRESS
DECODER
DATA
REGISTER
WP
VCC
7bits
ADDRESS REGISTER
GND
Ground
∗ An open drain output requires a pull-up resistor.
START
CONTROL LOGIC
STOP
SCL
SDA
ACK
HIGH VOLTAGE GEN.
VCC LEVEL DETECT
GND
BR24C02-W / F-W / FJ-W / FV-W
Pin name
A0, A1, A2
SCL
Function
Slave address setting pin
Serial data clock
Serial data input / output
Write protect pin
Power supply
2kbits EEPROM ARRAY
1
2
3
4
8
VCC
A0
A1
A2
∗
8bits
8bits
SDA
WP
ADDRESS
DECODER
SLAVE
·
WORD
DATA
REGISTER
7
6
5
WP
VCC
8bits
ADDRESS REGISTER
GND
Ground
∗ An open drain output requires a pull-up resistor.
START
CONTROL LOGIC
STOP
SCL
SDA
ACK
HIGH VOLTAGE GEN.
VCC LEVEL DETECT
GND
BR24C04-W / F-W / FJ-W / FV-W
Pin name
A0
Function
N.C.
4kbits EEPROM ARRAY
1
2
3
4
8
7
6
5
VCC
A1, A2
SCL
Slave address setting pin
Serial data clock
Serial data input / output
Write protect pin
Power supply
A0
A1
A2
8bits
9bits
∗
SDA
ADDRESS
DECODER
SLAVE
·
WORD
DATA
REGISTER
WP
WP
9bits
ADDRESS REGISTER
V
CC
GND
Ground
START
CONTROL LOGIC
STOP
∗ An open drain output requires a pull-up resistor.
SCL
SDA
ACK
HIGH VOLTAGE GEN.
VCC LEVEL DETECT
GND
BR24C01A-W / BR24C01AF-W / BR24C01AFJ-W / BR24C01AFV-W / BR24C02-W / BR24C02F-W /
BR24C02FJ-W / BR24C02FV-W / BR24C04-W / BR24C04F-W / BR24C04FJ-W / BR24C04FV-W
Memory ICs
!Electrical characteristics
DC characteristics (unless otherwise noted, Ta = −40 to + 85 °C, VCC = 2.7 to 5.5V)
Parameter
Symbol
Min.
Typ.
Max.
−
Unit
V
Conditions
Input high level voltage
Input low level voltage
Output low level coltage
Input leakage current
Output leakage current
operatingcurrent dissipation
V
IH
IL
OL
LI
LO
CC
0.7VCC
−
−
−
−
−
−
−
−
V
−
−
0.3VCC
0.4
1
V
V
V
IOL=3.0mA(SDA)
I
−1
−1
−
µA
µA
mA
V
V
V
V
IN=0V
OUT=0V
CC=5.5V, fSCL=400kHz
CC=5.5V, SDA SCL=VCC
~
V
CC
I
1
~
V
CC
I
2.0
·
Standby current
I
SB
−
−
2.0
µA
A0, A1, A2=GND, WP=GND
Not designed for radiation resistance.
Operating timing characteristics (unless otherwise noted, Ta = −40 to + 85 °C, VCC = 2.7 to 5.5V)
Vcc=5V 10%
Vcc=3V 10%
Parameter
Symbol
Unit
Min. Typ. Max. Min. Typ. Max.
f
SCL
HIGH
LOW
−
0.6
1.2
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
400
−
−
4.0
4.7
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
100
−
kHz
µs
µs
µs
µs
µs
µs
ns
ns
µs
µs
µs
µs
ms
µs
SCL frequency
Data clock HIGH time
t
Data clock LOW time
t
−
−
SDA / SCL rise time
t
R
0.3
0.3
−
1.0
0.3
−
SDA / SCL fall time
t
F
−
−
Start condition hold time
Start condition setup time
Input data hold time
t
HD : STA
SU : STA
HD : DAT
SU : DAT
0.6
0.6
0
4.0
4.7
0
t
−
−
t
−
−
Input data setup time
t
100
0.1
0.1
0.6
1.2
−
−
250
0.2
0.2
4.7
4.7
−
−
Output data delay time
Output data hold time
t
PD
0.9
−
3.5
−
t
DH
Stop condition setup time
Bus open time before start of transfer
Internal write cycle time
Noise erase valid time (SCL / SDA pins)
t
SU : STO
−
−
t
BUF
WR
−
−
t
10
0.05
10
0.1
t
I
−
−
BR24C01A-W / BR24C01AF-W / BR24C01AFJ-W / BR24C01AFV-W / BR24C02-W / BR24C02F-W /
BR24C02FJ-W / BR24C02FV-W / BR24C04-W / BR24C04F-W / BR24C04FJ-W / BR24C04FV-W
Memory ICs
!Timing charts
t
R
t
F
tHIGH
SCL
t
HD
:
STA
t
SU : DAT
t
LOW
PD
tHD : DAT
SDA
(input)
t
BUF
t
tDH
SDA
(output)
SCL
SDA
t
SU : STA
t
HD : STA
tSU : STO
START BIT
STOP BIT
· Data is read on the rising edge of SCL.
· Data is output in synchronization with the falling edge of SCL.
Fig.1 Synchronized data input / output timing
SCL
SDA
D0
ACK
Write data
tWR
(n address)
Stop condition
Start condition
Fig.2 Write cycle timing
!Circuit operation
(1) Start condition (recognition of start bit)
Before executing any command, when SCL is HIGH, a start condition (start bit) is required to cause SDA to fall from
HIGH to LOW. This IC is designed to constantly detect whether there is a start condition (start bit) for the SDA and
SCL line, and no commands will be executed unless this condition is satisfied.
(See Fig.1 for the synchronized data input / output timing.)
(2) Stop condition (recognition of stop bit)
To stop any command, a stop condition (stop bit) is required. A stop condition is achieved when SDA goes from
LOW to HIGH while SCL is HIGH. This enables commands to be completed.
(See Fig.1 for the synchronized data input / output timing.)
(3) Precautions concerning write commands
In the WRITE mode, the transferred data is not written to the memory unless the stop bit is executed.
BR24C01A-W / BR24C01AF-W / BR24C01AFJ-W / BR24C01AFV-W / BR24C02-W / BR24C02F-W /
BR24C02FJ-W / BR24C02FV-W / BR24C04-W / BR24C04F-W / BR24C04FJ-W / BR24C04FV-W
Memory ICs
(4) Device addressing
– BR24C01A-W / AF-W / AFJ-W / AFV-W, BR24C02-W / F-W / FJ-W / FV-W
1) Make sure the slave address is output from the master immediately after the start condition.
2) The upper four bits of the slave address are used to determine the device type. The device code for this IC is
fixed at “1010”.
3) The next three bits of the slave address (A2, A1, A0 … device address) are used to select the device. This IC
can address up to eight devices on the same bus.
4) The lowermost bit of the slave address (R / W … READ / WRITE) is used to set the write or read mode as follows.
R / W set to 0 … Write
(Random read word address setting is also 0)
R / W set to 1 … Read
1010
A2
A1
A0
R / W
– BR24C04-W / F-W / FJ-W / FV-W
1) Make sure the slave address is output from the master in continuation with the start condition.
2) The upper four bits of the slave address are used to determine the device type. The device code for this IC is
fixed at “1010”.
3) The next two bits of the slave address (A2, A1, … device address) are used to select the device. This IC can
address up to four devices on the same bus.
4) The next bit of the slave address (PS … Page Select) is used to select the page. As shown below, it can write to
or read from any of the 256 words in the two pages in memory.
PS set to 0 … Page 1 (000 to 0FF)
PS set to 1 … Page 2 (100 to 1FF)
5) The lowermost bit of the slave address (R / W … READ / WRITE) is used to set the write or read mode as follows.
R / W set to 0 … Write
(Random read word address setting is also 0)
R / W set to 1 … Read
1010
A2
A1
PS
R / W
(5) Write protect (WP)
When WP pin set to VCC (High level), write protect is set by all address. When WP pin set to GND (Low level),
enable to write to all address. Either control this pin or connect to GND (or VCC). It is inhibited from being left
unconnected.
(6) ACK signal
The acknowledge signal (ACK signal) is determined by software and is used to indicate whether or not a data transfer
is proceeding normally. The transmitting device, whether the master or slave, opens the bus after an 8-bit data
output (µ-COM when a write or read command of the slave address input ; this IC when reading data).
For the receiving device during the ninth clock cycle, SDA is set to LOW and an acknowledge signal (ACK signal) is
sent to indicate that it received the 8-bit data (this IC when a write command or a read command of the slave address
input, µ-COM when a read command data output).
The ICs output a LOW acknowledge signal (ACK signal) after recognizing the start condition and slave address (8
bits).
When data is being write to the ICs, a LOW acknowledge signal (ACK signal) is output after the receipt of each eight
bits of data (word address and write data).
BR24C01A-W / BR24C01AF-W / BR24C01AFJ-W / BR24C01AFV-W / BR24C02-W / BR24C02F-W /
BR24C02FJ-W / BR24C02FV-W / BR24C04-W / BR24C04F-W / BR24C04FJ-W / BR24C04FV-W
Memory ICs
When data is being read from the IC, eight bits of data (read data) are output and the IC waits for a returned LOW
acknowledge signal (ACK signal). When an acknowledge signal (ACK signal) is detected and a stop condition is not
sent from the master (µ-COM) side, the IC continues to output data. If an acknowledge signal (ACK signal) is not
detected, the IC interrupts the data transfer and ceases reading operations after recognizing the stop condition (stop
bit). The IC then enters the waiting or standby state.
(See Fig.3 for acknowledge signal (ACK signal) response.)
Start condition (start bit)
1
9
SCL
8
(from µ-COM)
SDA
(µ-COM output data)
SDA
(IC output data)
Acknowledge signal (ACK signal)
Fig.3 Acknowledge (ACK signal) response
(during write and read slave address input)
(7) Byte write cycle
BR24C01A-W / AF-W / AFJ-W / AFV-W
S
T
A
R
T
W
R
I
T
E
S
T
O
P
SLAVE
ADDRESS
WORD
ADDRESS
DATA
SDA
LINE
WA
6
WA
0
1
0
1
0
A2 A1 A0
D7
D0
∗
R
/
A
C
A
C
K
A
C
K
W K
WP
Fig.4
BR24C01A-W / BR24C01AF-W / BR24C01AFJ-W / BR24C01AFV-W / BR24C02-W / BR24C02F-W /
BR24C02FJ-W / BR24C02FV-W / BR24C04-W / BR24C04F-W / BR24C04FJ-W / BR24C04FV-W
Memory ICs
BR24C02-W / F-W / FJ-W / FV-W
S
T
A
R
T
W
R
I
T
E
S
T
O
P
SLAVE
ADDRESS
WORD
ADDRESS
DATA
SDA
LINE
WA
7
WA
0
1
0
1
0
A2 A1 A0
D7
D0
R
/
A
C
A
C
K
A
C
K
W K
WP
Fig.5
BR24C04-W / F-W / FJ-W / FV-W
S
T
A
R
T
W
R
I
T
E
S
T
O
P
SLAVE
ADDRESS
WORD
ADDRESS
DATA
SDA
LINE
WA
7
WA
0
1
0
1
0
A2 A1 PS
D7
D0
R
/
A
C
A
C
K
A
C
K
W K
WP
Fig.6
• Data is written to the address designated by the word address (n address).
• After eight bits of data are input, the data is written to the memory cell by issuing the stop bit.
(8) Page write cycle
BR24C01A-W / AF-W / AFJ-W / AFV-W
S
T
A
R
T
W
R
I
T
E
S
T
O
P
SLAVE
ADDRESS
WORD
ADDRESS(n)
DATA(n)
DATA(n+7)
SDA
LINE
WA
6
WA
0
1
0
1
0 A2 A1A0
D7
D0
D0
∗
R A
A
C
K
A
C
K
A
C
K
/
C
W K
WP
Fig.7
BR24C01A-W / BR24C01AF-W / BR24C01AFJ-W / BR24C01AFV-W / BR24C02-W / BR24C02F-W /
BR24C02FJ-W / BR24C02FV-W / BR24C04-W / BR24C04F-W / BR24C04FJ-W / BR24C04FV-W
Memory ICs
• A 8-byte write is possible using this command.
• Th page write command arbitrarily sets the upper four bits (WA6 to WA3) of the word address. The lower three bits
(WA2 and WA0) can write up to eight bytes of data with the address being incremented internally.
BR24C02-W / F-W / FJ-W / FV-W
S
T
A
R
T
W
R
I
T
E
S
T
O
P
SLAVE
ADDRESS
WORD
ADDRESS(n)
DATA(n)
DATA(n+7)
SDA
LINE
WA
7
WA
0
1
0
1
0 A2 A1A0
D7
D0
D0
R A
A
C
K
A
C
K
A
C
K
/
C
W K
WP
Fig.8
• A 8-byte write is possible using this command.
• Th page write command arbitrarily sets the upper five bits (WA7 to WA3) of the word address. The lower three bits
(WA2 and WA0) can write up to eight bytes of data with the address being incremented internally.
BR24C04-W / F-W / FJ-W / FV-W
S
T
A
R
T
W
R
I
T
E
S
T
O
P
SLAVE
ADDRESS
WORD
ADDRESS(n)
DATA(n)
DATA(n+15)
SDA
LINE
WA
7
WA
0
1
0
1
0 A2 A1PS
D7
D0
D0
R A
A
C
K
A
C
K
A
C
K
/
C
W K
WP
Fig.9
• A 16-byte write is possible using this command.
• Th page write command arbitrarily sets the upper four bits (WA7 to WA4) of the word address. The lower four bits
(WA3 and WA0) can write up to sixteen bytes of data with the address being incremented internally.
BR24C01A-W / BR24C01AF-W / BR24C01AFJ-W / BR24C01AFV-W / BR24C02-W / BR24C02F-W /
BR24C02FJ-W / BR24C02FV-W / BR24C04-W / BR24C04F-W / BR24C04FJ-W / BR24C04FV-W
Memory ICs
(9) Current read cycle
BR24C01A-W / AF-W / AFJ-W / AFV-W
S
T
A
R
T
R
E
A
D
S
T
SLAVE
ADDRESS
DATA
DATA
DATA
O
P
SDA
LINE
1
1
1
0
0
0
1
0
A2 A1 A0
D7
D0
D0
D0
R
/
W
A
C
K
A
C
K
Fig.10
BR24C02-W / F-W / FJ-W / FV-W
S
T
A
R
T
R
S
T
O
P
E
A
D
SLAVE
ADDRESS
SDA
LINE
1
0
A2 A1 A0
D7
R
/
W
A
C
K
A
C
K
Fig.11
BR24C04-W / F-W / FJ-W / FV-W
S
T
A
R
T
R
S
T
O
P
E
A
D
SLAVE
ADDRESS
SDA
LINE
1
0
A2 A1 PS
D7
R
/
W
A
C
K
A
C
K
Fig.12
• In case the previous operation is random or current read (which includes sequential read respectively), the internal
address counter is increased by one from the last accessed address (n). Thus current read outputs the data of the
next word address (n+1).
If the last command is byte or page write, the internal address counter stays at the last address (n). Thus current
read outputs the data of the word address (n).
If the master does not transfer the acknowledge but does generate a stop condition, the current address read
operation only provides s single byte of data.
At this point, this IC discontinues transmission.
• When an ACK signal LOW is detected after D0 and a stop condition is not sent from the master (µ-COM), the next
word address data can be read. [All words all read enabled]
(See Fig.16 to 18 for the sequential read cycles.)
• This command is ended by inputting HIGH to the ACK signal after D0 and raising the SDA signal (stop condition) by
setting SCL to HIGH.
BR24C01A-W / BR24C01AF-W / BR24C01AFJ-W / BR24C01AFV-W / BR24C02-W / BR24C02F-W /
BR24C02FJ-W / BR24C02FV-W / BR24C04-W / BR24C04F-W / BR24C04FJ-W / BR24C04FV-W
Memory ICs
(10) Random read cycle
BR24C01A-W / AF-W / AFJ-W / AFV-W
S
T
A
R
T
W
R
I
T
E
S
T
A
R
T
R
E
A
D
S
T
SLAVE
ADDRESS
WORD
ADDRESS(n)
SLAVE
ADDRESS
O
P
DATA(n)
DATA(n)
DATA(n)
SDA
LINE
WA
WA
0
1
0
1
0 A2 A1A0
1
1
1
0
0
0
1
0 A2 A1A0
D7
D7
D7
D0
D0
D0
∗
6
R A
A
C
K
R A
A
C
K
/
C
/ C
W K
W K
Fig.13
BR24C02-W / F-W / FJ-W / FV-W
S
T
A
R
T
W
S
T
A
R
T
R
E
A
D
R
I
S
T
O
P
SLAVE
WORD
SLAVE
ADDRESS
T
E
ADDRESS
ADDRESS(n)
SDA
LINE
WA
7
WA
0
1
0
1
0 A2 A1A0
1 0 A2A1A0
R A
/ C
W K
A
C
K
R A
A
C
K
/ C
W K
Fig.14
BR24C04-W / F-W / FJ-W / FV-W
S
T
A
R
T
W
S
T
A
R
T
R
E
A
D
R
I
S
T
O
P
SLAVE
WORD
SLAVE
ADDRESS
T
E
ADDRESS
ADDRESS(n)
SDA
LINE
WA
7
WA
0
1
0
1
0 A2 A1PS
1 0 A2A1PS
R A
A
C
K
R A
A
C
K
/
C
/ C
W K
W K
Fig.15
• This command can read the designated word address data.
• When an ACK signal LOW is detected after D0 and a stop condition is not sent from the master (µ-COM), the next
word address data can be read. [All words all read enabled]
(See Fig.16 to 18 for the sequential read cycles.)
• This command is ended by inputting a HIGH signal to the ACK signal after D0 and raising the SDA signal (stop
condition) by raising SCL to HIGH.
BR24C01A-W / BR24C01AF-W / BR24C01AFJ-W / BR24C01AFV-W / BR24C02-W / BR24C02F-W /
BR24C02FJ-W / BR24C02FV-W / BR24C04-W / BR24C04F-W / BR24C04FJ-W / BR24C04FV-W
Memory ICs
(11) Sequential read cycle (For a current read)
BR24C01A-W / AF-W / AFJ-W / AFV-W
S
R
E
A
D
T
A
R
T
S
T
O
P
SLAVE
ADDRESS
DATA(n)
DATA(n)
DATA(n)
DATA(n+x)
DATA(n+x)
DATA(n+x)
SDA
LINE
1
0
1
0 A2 A1A0
D7
D7
D7
D0
D7
D7
D7
D0
D0
D0
R A
A
C
K
A
C
K
A
C
K
/
C
W K
Fig.16
BR24C02-W / F-W / FJ-W / FV-W
S
T
A
R
E
A
D
S
T
SLAVE
R
ADDRESS
T
O
P
SDA
LINE
1
0
1
0 A2 A1A0
D0
R A
A
C
K
A
C
K
A
C
K
/
C
W K
Fig.17
BR24C04-W / F-W / FJ-W / FV-W
S
T
A
R
E
A
D
S
T
O
P
SLAVE
R
ADDRESS
T
SDA
LINE
1
0
1
0 A2 A1PS
D0
R A
A
C
K
A
C
K
A
C
K
/
C
W K
Fig.18
• When an ACK signal LOW is detected after D0 and a stop condition is not sent from the master (µ-COM), the next
word address data can be read. [All words can be read]
• This command is ended by inputting a HIGH signal to the ACK signal after D0 and raising the SDA signal (stop
condition) using the SCL signal HIGH.
• Sequential reading can also be done with a random read.
BR24C01A-W / BR24C01AF-W / BR24C01AFJ-W / BR24C01AFV-W / BR24C02-W / BR24C02F-W /
BR24C02FJ-W / BR24C02FV-W / BR24C04-W / BR24C04F-W / BR24C04FJ-W / BR24C04FV-W
Memory ICs
!Operation notes
(1) During power rise
During power rise, the VCC may rise passing though the low voltage domain in which the IC internal circuit does not
work. For this reason, there is a risk of misoperation when the power rises without full IC internal reset.
To prevent this, pay attention to the following points during a power rise.
1) Set SCL = SDA = “HIGH”
2) Raise the power so as to active the Power On Reset (P. O. R) circuit.
Follow the steps below as to operate the P. O. R. circuit properly.
1) Set the power rise time (tR) to within 10ms.
2) Set the OFF domain for once power has been cut to 100mS minimum.
V
CC
t
R
t
OFF
(2) SDA terminal pull-up resistance
The SDA terminal is an open drain output. Consequently, it requires an external pull-up resistance. The
appropriate pull-up resistance value is selected from the IC VOL-IOL features., which have been appended as
measuring data, as well as VIL and ILI and other personal icons that control the IC in question.
Recommended values 2.0k to 10kW
0.45
0.4
0.35
0.3
0.25
0.2
0.15
0.1
0.05
0
0
1
2
3
4
5
OUTPUT CURRENT : IOL (mA)
V
CC=3.0V
V
CC=5.0V
V
CC=3.0V CC=5.0V
V
V
CC=3.0V
VCC=5.0V
Ta=85°C
Ta=25°C
Ta=−40°C
Fig.19 VOL−IOL features (Note : Typ.)
Note : All memory array data are set to “FF” status at time of shipping.
BR24C01A-W / BR24C01AF-W / BR24C01AFJ-W / BR24C01AFV-W / BR24C02-W / BR24C02F-W /
BR24C02FJ-W / BR24C02FV-W / BR24C04-W / BR24C04F-W / BR24C04FJ-W / BR24C04FV-W
Memory ICs
!External dimensions (Units : mm)
BR24C01A-W
BR24C02-W
BR24C04-W
BR24C01AF-W
BR24C02F-W
BR24C04F-W
9.3 0.3
8
5
5.0 0.2
8
5
1
4
1
4
7.62
1.27 0.4 0.1
0.3Min.
0.15
2.54
0.5 0.1
DIP8
0 ~ 15
SOP8
BR24C01AFJ-W
BR24C02FJ-W
BR24C04FJ-W
BR24C01AFV-W
BR24C02FV-W
BR24C04FV-W
4.9 0.2
3.0 0.2
8
7
6
5
8
5
1
4
1
2
3
4
0.22 0.1
0.3Min.
0.45Min.
(0.52)
0.65
1.27
0.42 0.1
0.1
0.1
SOP-J8
SSOP-B8
相关型号:
©2020 ICPDF网 联系我们和版权申明