BD63565EFV [ROHM]
BD63565EFV 为内置2ch FULL ON驱动H桥的电机驱动器。通过1.8V到16.0V即可动作的低导通电阻DMOS输出+高速开关实现低耗电,通过小型表面封装满足移动设备、家用电器等各种组件的需求。;![BD63565EFV](http://pdffile.icpdf.com/pdf2/p00358/img/icpdf/BD63565EFV_2196821_icpdf.jpg)
型号: | BD63565EFV |
厂家: | ![]() |
描述: | BD63565EFV 为内置2ch FULL ON驱动H桥的电机驱动器。通过1.8V到16.0V即可动作的低导通电阻DMOS输出+高速开关实现低耗电,通过小型表面封装满足移动设备、家用电器等各种组件的需求。 开关 电机 驱动 驱动器 |
文件: | 总16页 (文件大小:1614K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
Datasheet
H-Bridge Drivers for DC Brush Motors
Dual H-Bridge Driver
High-Speed Switching Type
BD63565EFV
General Description
Key Specifications
The BD63565EFV provides a dual H-bridge motor driver
which features wide range of motor power supply
voltage from 1.8V to 16.0V and low power consumption
to switch low ON-Resistance DMOS transistors at high
speed. This small surface mounting package is most
suitable for mobile system, home appliance and various
applications.
Power Supply Voltage Range:
Motor Power Supply Voltage Range:1.8V to 16.0V
Circuit Current (Open Mode):
Stand-By Current:
Control Input Voltage Range:
Logic Input Frequency:
Minimum Logic Input Pulse Width:
Turn On Time:
Turn Off Time:
H-Bridge Output Current (DC):
Output ON-Resistance (Total):
Operating Temperature Range:
2.5V to 5.5V
0.90mA(Typ)
1μA (Max)
0V to VCCV
500kHz(Max)
0.5μs(Min)
200ns(Typ)
80ns(Typ)
-1.0A to +1.0A
0.90Ω(Typ)
Features
Low ON-Resistance Power DMOS Output
Charge Pump-Less with PDMOS High-Side Driver
Drive Mode Switch Function
Control Input Voltage Range Fit 1.8V Controller
Under Voltage Locked Out Protection
& Thermal Shut Down Circuit
-40°C to +85°C
Package
HTSSOP-B20
W(Typ) x D(Typ) x H(Max)
6.50mm x 6.40mm x 1.00mm
Applications
Mobile system
Home appliance
Amusement system, etc
HTSSOP-B20
Typical Application Circuit
Bypass Filter Capacitor for
Power Supply
1µF to 100µF
Power-Saving
H: Active
VCC
20
L: Stand-by
Bypass Filter Capacitor for
Power Supply
PS
17
Power Save
TSD & UVLO
BandGap
1µF to 100µF
VM
5
7
Motor Control Input
OUT1A
6
9
Level Shift
&
Pre Driver
IN1A
IN1B
2
3
H-Bridge
Full ON
Logic
10
OUT1B
Selectable Drive Mode
H: EN/IN
L: IN/IN
PWM
4
VM
16
OUT2A
14 15
11 12
Level Shift
&
Pre Driver
IN2A
IN2B
19
18
H-Bridge
Full ON
Logic
OUT2B
PGND
Motor Control Input
8
13
1
GND
It's better for VM pin groups of 5,16 to short-circuit on the PCB
pattern. If cannot, check into transitional characteristics of total
application circuit including two motors. Through low impedance
materials, the possibility of causing some unexpected malfunctions
is incontrovertible.
〇Product structure : Silicon monolithic integrated circuit 〇This product has no designed protection against radioactive rays
.www.rohm.com
TSZ02201-0H3H0B300560-1-2
27.Jun.2017 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
1/13
TSZ22111 • 14 • 001
BD63565EFV
Pin Configuration
(TOP VIEW)
20
19
GND
IN1A
IN1B
PWM
VCC
IN2A
1
2
3
4
IN2B
PS
18
17
16
15
14
The pins of the same name, such
as VM, PGND, OUT1A, OUT1B,
OUT2A and OUT2B, must be
shorted on printed circuit boards.
VM
OUT1A
OUT1A
VM
5
6
OUT2A
OUT2A
7
8
9
PGND
13 PGND
12
OUT1B
OUT2B
OUT1B 10
11 OUT2B
Pin Description
Pin No.
Pin Name
Function
Pin No.
Pin Name
Function
1
2
GND
IN1A
Ground
11
12
13
14
15
16
17
18
19
20
OUT2B
OUT2B
PGND
OUT2A
OUT2A
VM
H-bridge output 2B
H-bridge output 2B
Motor ground
Control logic input 1A
Control logic input 1B
Drive mode logic input
Motor power supply
H-bridge output 1A
H-bridge output 1A
Motor ground
3
IN1B
4
PWM
H-bridge output 2A
H-bridge output 2A
Motor power supply
Power-saving function
Control logic input 2B
Control logic input 2A
Power supply
5
VM
6
OUT1A
OUT1A
PGND
OUT1B
OUT1B
7
PS
8
IN2B
9
H-bridge output 1B
H-bridge output 1B
IN2A
10
VCC
Block Diagram
VCC
20
PS 17
Power Save
TSD & UVLO
BandGap
5
VM
6
9
7
OUT1A
OUT1B
Level Shift
&
Pre Driver
IN1A
2
3
H-Bridge
Full ON
Logic
IN1B
10
PWM
4
16
VM
14 15
11 12
OUT2A
OUT2B
Level Shift
&
Pre Driver
IN2A
IN2B
19
18
H-Bridge
Full ON
Logic
8
13
PGND
1
GND
www.rohm.com
TSZ02201-0H3H0B300560-1-2
27.Jun.2017 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
2/13
TSZ22111 • 15 • 001
BD63565EFV
Description of Blocks
1. Power-Saving Function
A power-saving function is included, which allows the system to save power when not driving the motor. The voltage
level on this pin should be set high so as to keep the operation mode. (See the Electrical Characteristics; p.4/13)
2. Motor Control Input
(a) IN1A, IN1B, IN2A and IN2B Pins
Logic level controls the output logic of H-Bridge.
(See the Electrical Characteristics; p.4/13, and I/O Truth Table; p.7/13)
(b) PWM Pin
Logic level sets the IN/IN or EN/IN drive mode.
(See the Electrical Characteristics; p.4/13 and I/O Truth Table; p.7/13)
3. VM Terminal
Each H-bridge can be controlled independently. Take into consideration that each VM terminal (5 and 16pin) is
short-circuited internally.
(See the Block Diagram; p.2/13)
Absolute Maximum Ratings (Ta=25°C)
Parameter
Power Supply Voltage
Symbol
Limit
Unit
-0.3 to +7.0
-0.3 to +20.0
-0.3 to +VCC+0.3
-1.0 to +1.0(Note 1)
150
V
V
VCC
VM
Motor Power Supply Voltage
Control Input Voltage
VIN
V
IOUT
Tjmax
Tstg
A
H-bridge Output Current (DC)
Maximum Junction Temperature
°C
°C
Storage Temperature Range
-55 to +150
(Note 1) Must not exceed ASO, or Tjmax of 150°C
Caution 1: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is
operated over the absolute maximum ratings.
Caution 2: Should by any chance the maximum junction temperature rating be exceeded the rise in temperature of the chip may result in deterioration of the
properties of the chip. In case of exceeding this absolute maximum rating, design a PCB boards with thermal resistance taken into consideration
by increasing board size and copper area so as not to exceed the maximum junction temperature rating.
Recommended Operating Conditions
Parameter
Power Supply Voltage
Symbol
Min
2.5
1.8
0
Typ
Max
5.5
16.0
VCC
500
-
Unit
V
-
-
-
-
-
-
VCC
VM
Motor Power Supply Voltage
Control Input Voltage
V
V
VIN
Logic Input Frequency
FIN
0
kHz
μs
°C
Minimum Logic Input Pulse Width
Operating Temperature Range
TIN
0.5
-40
Topr
+85
www.rohm.com
TSZ02201-0H3H0B300560-1-2
27.Jun.2017 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
3/13
TSZ22111 • 15 • 001
BD63565EFV
Thermal Resistance(Note 2)
Thermal Resistance (Typ)
Parameter
Symbol
Unit
1s(Note 4)
2s2p(Note 5)
HTSSOP-B20
Junction to Ambient
Junction to Top Characterization Parameter(Note 3)
θJA
143.0
8
26.8
4
°C/W
°C/W
ΨJT
(Note 2) Based on JESD51-2A(Still-Air).
(Note 3) The thermal characterization parameter to report the difference between junction temperature and the temperature at the top center of the outside
surface of the component package.
(Note 4) Using a PCB board based on JESD51-3.
Layer Number of
Measurement Board
Material
FR-4
Board Size
Single
114.3mm x 76.2mm x 1.57mmt
Top
Copper Pattern
Thickness
Footprints and Traces
70μm
(Note 5) Using a PCB board based on JESD51-5, 7.
Thermal Via(Note 6)
Layer Number of
Material
Board Size
Measurement Board
Pitch
1.20mm
Diameter
4 Layers
FR-4
114.3mm x 76.2mm x 1.6mmt
2 Internal Layers
Φ0.30mm
Top
Bottom
Copper Pattern
Thickness
Copper Pattern
Thickness
35μm
Copper Pattern
Thickness
70μm
Footprints and Traces
70μm
74.2mm x 74.2mm
74.2mm x 74.2mm
(Note 6) This thermal via connects with the copper pattern of all layers.
Electrical Characteristics (Unless otherwise specified VCC=3.0V, VM=5.0V, Ta=25°C)
Parameter
All Circuits
Symbol
Min
Typ
Max
Unit
Conditions
Stand-by Current
ICCST
ICC1
ICC2
ICC3
-
0
1
μA
mA
mA
mA
VPS=0V
Circuit Current 1
0.50
0.50
0.50
0.90
0.95
0.95
1.25
1.30
1.30
VPS=3V, Open Mode
Circuit Current 2
VPS=3V, CW & CCW Mode
VPS=3V, Short Brake Mode
Circuit Current 3
PS Input (PS)
High-Level Input Voltage
Low-Level Input Voltage
High-Level Input Current
Low-Level Input Current
VPSH
VPSL
IPSH
IPSL
1.45
0
-
-
VCC
0.5
60
V
V
15
-1
30
0
μA
μA
VPS=3V
VPS=0V
+1
Control Input (IN=IN1A, IN1B, IN2A, IN2B, PWM)
High-Level Input Voltage
Low-Level Input Voltage
High-Level Input Current
Low-Level Input Current
VINH
VINL
IINH
IINL
1.45
0
-
-
VCC
0.5
60
V
V
15
-1
30
0
μA
μA
VIN=3V
VIN=0V
+1
Under Voltage Locked Out (UVLO)
UVLO Voltage
VUVLO
2.0
-
2.4
V
Full ON Type H-Bridge Driver
Output ON-Resistance
Turn On Time
RON
TON
-
-
-
0.9
200
80
1.2
400
400
Ω
IOUT=±500mA,High & Low-side total
20Ω Loading
ns
ns
Turn Off Time
TOFF
20Ω Loading
www.rohm.com
TSZ02201-0H3H0B300560-1-2
27.Jun.2017 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
4/13
TSZ22111 • 15 • 001
BD63565EFV
Typical Performance Curves (Reference data)
5.0
3.0
2.0
1.0
0.0
Top 85°C
Mid 25°C
Low -40°C
4.0
Top 85°C
Mid 25°C
Low -40°C
3.0
Operating Range
(2.5V to 5.5V)
Operating Range
(2.5V to 5.5V)
2.0
1.0
0.0
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
Power Supply Voltage : VCC [V]
Power Supply Voltage : VCC [V]
Figure 1.
Figure 2.
Circuit Current vs Power Supply Voltage
(Open Mode)
Circuit Current vs Power Supply Voltage
(Stand-by Mode)
800
600
400
200
0
800
600
400
200
0
Top 85°C
Mid 25°C
Low -40°C
Top 85°C
Mid 25°C
Low -40°C
0
200
400
600
800
1000
0
200
400
600
800
1000
Power Output Current : IOUT [mA]
Power Output Current : IOUT [mA]
Figure 3.
Figure 4.
Output VDS vs Power Output Current
Output VDS vs Power Output Current
(Output On-Resistance on high-side, VM=5V, VCC=3V)
(Output On-Resistance on low-side VM=5V, VCC=3V)
www.rohm.com
TSZ02201-0H3H0B300560-1-2
27.Jun.2017 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
5/13
TSZ22111 • 15 • 001
BD63565EFV
Typical Performance Curves (Reference Data) - continued
1.0
0.8
0.6
0.4
0.5
0.4
0.3
0.2
0.1
0.0
Operating Range
(1.8V to 16.0V)
Operating Range
0.2
(1.8V to 16.0V)
Top 85°C
Mid 25°C
Low -40°C
Top 85°C
Mid 25°C
Low -40°C
0.0
0
5
10
15
20
0
5
10
15
20
Motor Power Supply Voltage : VM [V]
Motor Power Supply Voltage : VM [V]
Figure 5.
Figure 6.
Output On-Resistance vs Motor Power Supply Voltage
Output On-Resistance vs Motor Power Supply Voltage
(Output On-Resistance on high-side VM Dependency, VCC=3V) (Output On-Resistance on low-side VM Dependency, VCC=3V)
www.rohm.com
TSZ02201-0H3H0B300560-1-2
27.Jun.2017 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
6/13
TSZ22111 • 15 • 001
BD63565EFV
Timing Chart
Table 1. I/O Truth Table
Input Mode
INPUT
PWM IN1A/2A IN1B/2B OUT1A/2A
OUTPUT
PS(Note 7)
Output Mode(Note 8)
Short Brake
CW
OUT1B/2B
L
H
H
L
X
L
L
H
L
L
L
EN/IN
H
H
L
H
Z
L
CCW
H
L
Z
H
L
Open
H
L
L
CW
IN/IN
-
L
H
H
X
H
L
CCW
H
X
L
Short Brake
Open
X
Z
Z
L: Low, H: High, X: Don’t care, Z: Hi impedance
(Note 7)PS=High: Operation Mode, PS=Low: Stand-by Mode
(Note 8)CW: Current flows from OUTxA to OUTxB, CCW: Current flows from OUTxB to OUTxA (x=1, 2)
1.45V
TIN
TIN
1.0V
Control Input
0.5V
TON
TON
TOFF
50%
TOFF
100%
0%
50%
Motor Current
-50%
-50%
-100%
Figure 7.
Input-Output AC Characteristic
www.rohm.com
TSZ02201-0H3H0B300560-1-2
27.Jun.2017 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
7/13
TSZ22111 • 15 • 001
BD63565EFV
Application Example
Bypass Filter Capacitor for
Power Supply
1µF to 100µF
Power-Saving
H: Active
VCC
20
L: Stand-by
Bypass Filter Capacitor for
Power Supply
PS 17
Power Save
TSD & UVLO
BandGap
1µF to 100µF
VM
5
7
Motor Control Input
OUT1A
6
9
Level Shift
&
Pre Driver
IN1A
2
3
H-Bridge
Full ON
Logic
IN1B
10
OUT1B
Selectable Drive Mode
H: EN/IN
L: IN/IN
PWM
4
VM
16
OUT2A
14 15
11 12
Level Shift
&
Pre Driver
IN2A
IN2B
19
18
H-Bridge
Full ON
Logic
OUT2B
PGND
Motor Control Input
8
13
1
GND
It's better for VM pin groups of 5,16 to short-circuit on the PCB
pattern. If cannot, check into transitional characteristics of total
application circuit including two motors. Through low impedance
materials, the possibility of causing some unexpected malfunctions
is incontrovertible.
Selection of Components Externally Connected
When using the circuit with changes to the external circuit constants, make sure to leave an adequate margin for external
components including static and transitional characteristics as well as dispersion of the IC.
I/O Equivalence Circuits
PS
IN1A, IN1B, IN2A, IN2B, PWM
VM, PGND, OUTxA, OUTxB (x=1,2)
VM
75kΩ
10kΩ
OUTxA
OUTxB
300kΩ
100kΩ
PGND
www.rohm.com
TSZ02201-0H3H0B300560-1-2
27.Jun.2017 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
8/13
TSZ22111 • 15 • 001
BD63565EFV
Operational Notes
1.
2.
Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power
supply pins.
Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the
digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog
block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and
aging on the capacitance value when using electrolytic capacitors.
3.
4.
Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
Ground Wiring Pattern
When using both small-signal(GND) and large-current ground(PGND) traces, the two ground traces should be routed
separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the
small-signal ground caused by large currents. Also ensure that the ground traces of external components do not
cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line
impedance.
5.
6.
Recommended Operating Conditions
The function and operation of the IC are guaranteed within the range specified by the recommended operating
conditions. The characteristic values are guaranteed only under the conditions of each item specified by the electrical
characteristics.
Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may
flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power
supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring,
and routing of connections.
7.
8.
Operation Under Strong Electromagnetic Field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may
subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply
should always be turned off completely before connecting or removing it from the test setup during the inspection
process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during
transport and storage.
9.
Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment)
and unintentional solder bridge deposited in between pins during assembly to name a few.
10. Unused Input Pins
Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and
extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small
charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and
cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the
power supply or ground line.
www.rohm.com
TSZ02201-0H3H0B300560-1-2
27.Jun.2017 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
9/13
TSZ22111 • 15 • 001
BD63565EFV
Operational Notes – continued
11. Regarding the Input Pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them
isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a
parasitic diode or transistor. For example (refer to figure below):
When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic transistor.
Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual
interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to
operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should
be avoided.
Resistor
Transistor (NPN)
Pin A
Pin B
Pin B
B
E
C
Pin A
B
C
E
P
P+
P+
N
P+
P
P+
N
N
N
N
N
N
N
Parasitic
Elements
Parasitic
Elements
P Substrate
GND GND
P Substrate
GND
GND
Parasitic
Elements
Parasitic
Elements
N Region
close-by
Figure 8.
Example of monolithic IC structure
12. Ceramic Capacitor
When using a ceramic capacitor, determine a capacitance value considering the change of capacitance with
temperature and the decrease in nominal capacitance due to DC bias and others.
13. Area of Safe Operation (ASO)
Operate the IC such that the output voltage, output current, and the maximum junction temperature rating are all
within the Area of Safe Operation (ASO).
14. Thermal Shutdown Circuit(TSD)
This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation should always
be within the IC’s maximum junction temperature rating. If however the rating is exceeded for a continued period, the
junction temperature (Tj) will rise which will activate the TSD circuit that will turn OFF all output pins. When the Tj falls
below the TSD threshold, the circuits are automatically restored to normal operation.
Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no
circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from
heat damage.
www.rohm.com
TSZ02201-0H3H0B300560-1-2
27.Jun.2017 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
10/13
TSZ22111 • 15 • 001
BD63565EFV
Ordering Information
B D
6
3
5
6
5
E
F
V
-
E 2
Package
EFV :HTSSOP-B20
Packaging and forming specification
E2: Embossed tape and reel
Part Number
Marking Diagram
HTSSOP-B20 (TOP VIEW)
Part Number Marking
LOT Number
D 6 3 5 6 5
Pin 1 Mark
Part Number Marking
Package
HTSSOP-B20
Orderable Part Number
D63565
BD63565EFV-E2
www.rohm.com
TSZ02201-0H3H0B300560-1-2
27.Jun.2017 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
11/13
TSZ22111 • 15 • 001
BD63565EFV
Physical Dimension and Packing Information
Package Name
HTSSOP-B20
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0H3H0B300560-1-2
27.Jun.2017 Rev.002
12/13
BD63565EFV
Revision History
Date
Revision
Changes
04.Feb.2013
27.Jun.2017
001
002
New release
Applied the ROHM Standard Style and improved understandability.
www.rohm.com
TSZ02201-0H3H0B300560-1-2
27.Jun.2017 Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
13/13
TSZ22111 • 15 • 001
Notice
Precaution on using ROHM Products
1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PGA-E
Rev.003
© 2015 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PGA-E
Rev.003
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
相关型号:
![](http://pdffile.icpdf.com/pdf2/p00358/img/page/BD63572MUV_2194986_files/BD63572MUV_2194986_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00358/img/page/BD63572MUV_2194986_files/BD63572MUV_2194986_2.jpg)
BD63572MUV
BD63572MUV是一款FULL ON驱动、内置2通道H桥的电机驱动器。能够在2.0V至9.0V的电压下工作,并且由于具有低导通电阻DMOS输出和高速开关,实现低功耗。采用小型表面贴装封装,可以支持移动设备和家用电器等各种设备。
ROHM
![](http://pdffile.icpdf.com/pdf2/p00369/img/page/BD63573NUV_2253567_files/BD63573NUV_2253567_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00369/img/page/BD63573NUV_2253567_files/BD63573NUV_2253567_2.jpg)
BD63573NUV
BD63573NUV为内置1ch FULL ON驱动H桥的电机驱动器。通过2.0V到16.0V即可动作的低导通电阻DMOS输出+高速开关实现低耗电,通过小型表面封装满足移动设备、家用电器等各种组件的需求。
ROHM
![](http://pdffile.icpdf.com/pdf2/p00358/img/page/BD63576NUX_2195127_files/BD63576NUX_2195127_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00358/img/page/BD63576NUX_2195127_files/BD63576NUX_2195127_2.jpg)
BD63576NUX
BD63576NUX是一款FULL ON驱动、内置2通道H桥的电机驱动器。能够在2.0V至10.0V的电压下工作,并且由于具有低导通电阻DMOS输出和高速开关,实现低功耗。采用小型表面贴装封装,可以支持移动设备和家用电器等各种设备。
ROHM
![](http://pdffile.icpdf.com/pdf2/p00315/img/page/BD6360GUL-E2_1891348_files/BD6360GUL-E2_1891348_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00315/img/page/BD6360GUL-E2_1891348_files/BD6360GUL-E2_1891348_2.jpg)
BD6360GUL-E2
Stepper Motor Controller, 0.5A, PBGA15, 2.10 X 2.10 MM, 0.55 MM HEIGHT, ROHS COMPLIANT, VCSP-15
ROHM
![](http://pdffile.icpdf.com/pdf2/p00358/img/page/BD63610AEFV_2196249_files/BD63610AEFV_2196249_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00358/img/page/BD63610AEFV_2196249_files/BD63610AEFV_2196249_2.jpg)
BD63610AEFV
BD63610AEFV是额定电源36V、额定输出电流0.8A的低功耗双极PWM恒流驱动器。输入接口采用CLK-IN驱动方式,励磁模式可适用于FULL STEP、HALF STEP模式。另外,也可使用一个系统电源进行驱动,有助于提高整机设计的便利性。
ROHM
![](http://pdffile.icpdf.com/pdf2/p00358/img/page/BD63620AEFV_2195373_files/BD63620AEFV_2195373_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00358/img/page/BD63620AEFV_2195373_files/BD63620AEFV_2195373_2.jpg)
BD63620AEFV
BD63620AEFV是额定电源36V、额定输出电流2.0A的低功耗双极PWM恒流驱动器。输入接口采用CLK-IN驱动方式,通过内置DAC,励磁模式可适用于FULL STEP、HALF STEP(2种)、QUATER STEP模式。电流衰减方式方面可任意设定FAST DECAY/SLOW DECAY的比率,可对所有电机实现很好的控制状态。另外,也可使用一个系统电源进行驱动,有助于提高整机设计的便利性。
ROHM
![](http://pdffile.icpdf.com/pdf2/p00364/img/page/BD63621MUV_2226600_files/BD63621MUV_2226600_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00364/img/page/BD63621MUV_2226600_files/BD63621MUV_2226600_2.jpg)
BD63621MUV
BD63621MUV是一款电源额定电压36V、额定输出电流2.0A的低功耗双极PWM恒流驱动的驱动器。输入接口采用CLK-IN驱动方式,通过内置DAC,励磁模式可支持FULL STEP、HALF STEP(2种)、QUARTER STEP模式。在电流衰减方式中,可自由设置FAST DECAY/SLOW DECAY的比例,可使各种电机实现理想的控制状态。另外,电源也可以用1个系统进行驱动,使配套应用的设计更容易。
ROHM
©2020 ICPDF网 联系我们和版权申明