BD37515FS-E2 [ROHM]
Consumer Circuit, BICMOS, PDSO20, SSOP-20;![BD37515FS-E2](http://pdffile.icpdf.com/pdf2/p00291/img/icpdf/BD37515FS-E2_1765274_icpdf.jpg)
型号: | BD37515FS-E2 |
厂家: | ![]() |
描述: | Consumer Circuit, BICMOS, PDSO20, SSOP-20 信息通信管理 光电二极管 商用集成电路 |
文件: | 总29页 (文件大小:1328K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Sound Processor with Built-in 2-band Equalizer
BD37513FS
General Description
Key Specifications
BD37513FS is a sound processor with built-in 2-band
equalizer for car audio. The functions are 4ch stereo
input selector, input-gain control, main volume,
loudness, and 4ch fader volume. Moreover, its
“Advanced switch circuit”, which is an original ROHM
technology, can reduce various switching noise (ex.
No-signal, low frequency like 20Hz & large signal
inputs). “Advanced switch” makes control of
microcomputer easier, supporting the construction of a
high quality car audio system.
Power Supply Voltage Range:
Circuit Current (No Signal):
TotalHarmonic Distortion1:
Maximum Input Voltage:
Cross-talk Between Selectors:
Volume Control Range:
Output Noise Voltage 1:
Residual Output Noise Voltage:
Operating Temperature Range:
7.0V to 9.5V
38mA(Typ)
0.001%(Typ)
2.3Vrms(Typ)
-100dB(Typ)
+15dB to -79dB
3.8µVrms(Typ)
1.8µVrms(Typ)
-40°C to +85°C
Package
W(Typ) x D(Typ) x H(Max)
Features
Reduce switching noise of input gain control, mute,
main volume, fader volume, bass, treble, loudness
by using advanced switch circuit.
Built-in
1
differential input selector and
3
single-ended input selectors
Built-in ground isolation amplifier inputs, ideal for
external stereo input.
Built-in input gain controller reduces switching
noise for volume of a portable audio input.
Decrease the number of external components due
to built-in 2-band equalizer filter and loudness filter.
Also, it is possible to control Gv using I2C BUS
control.
SSOP-A20
8.70mm x 7.80mm x 2.01mm
It is possible to adjust the gain of the bass and
treble up to ±20dB with 1 dB step gain adjustment.
Energy-saving design resulting in low current
consumption, by utilizing the Bi-CMOS process. It
has the advantage in quality over scaling down the
power heat control of the internal regulators.
Input terminals and output terminals are organized
and separately laid out to keep the signal flow in
one direction which results in simpler and smaller
PCB layout.
Applications
It is optimal for use in car audio systems. It can also be
used for audio equipment of mini Compo, micro Compo,
TV, etc.
It is possible to control the I2C BUS by 3.3V/5V.
○Product structure:Silicon monolithic integrated circuit ○This product has no designed protection against radioactive rays
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
1/26
TSZ22111・14・001
BD37513FS
Typical Application Circuit
BD37513FS
Unit
R : [Ω]
C : [F]
Pin Configuration
20 GND
19 SDA
18 SCL
FIL 1
A1 2
A2 3
17 VCC
16 OUTF1
B1 4
B2 5
C1 6
C2 7
15 OUTF2
14 OUTR1
13 OUTR2
12 TEST1
11 MUTE
DP1 8
DN 9
DP2 10
Pin Descriptions
Pin
Pin No.
Description
Pin No.
Pin Name
Description
Name
1
2
FIL
A1
VCC/2 terminal
11
12
13
14
15
16
17
MUTE
TEST1
OUTR2
OUTR1
OUTF2
OUTF1
VCC
External compulsory mute terminal
Test Pin
A input terminal of 1ch
A input terminal of 2ch
B input terminal of 1ch
B input terminal of 2ch
C input terminal of 1ch
C input terminal of 2ch
3
A2
Rear output terminal of 2ch
Rear output terminal of 1ch
Front output terminal of 2ch
Front output terminal of 1ch
Power supply terminal
4
B1
5
B2
6
C1
7
C2
8
DP1
DN
DP2
D positive input terminal of 1ch
D negative input terminal
18
19
20
SCL
I2C Communication clock terminal
I2C Communication data terminal
GND terminal
9
SDA
10
D positive input terminal of 2ch
GND
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
2/26
TSZ22111・15・001
BD37513FS
Block Diagram
20
19
18
17
16
15
14
13
12
11
VCC
GND
I2C BUS LOGIC
■Fader
Gain: 0dB to -79dB/1dB step
★no pop noise
■Loudness
20dB to 0dB/1dB step
★no pop noise
・f0=800
・Hicut1/2/3/4
■2 Band EQ (Tone control)
Gain:+20dB to -20dB/1dB
★no pop noise
・Bass:f0=100Hz,
Q=1.0
★Loudness
・Treble:f0=10kHz
Q=1.25
■Volume
★2 Band EQ
(Tone control)
Gain+15dB to -79dB/1dB step
★no pop noise
■Input Gain
★Volume/Mute
★Input Gain
Gain:+20dB to 0dB/1dB step
★no pop noise
Input selector (3 single-end and 1 stereo ISO)
GND
GND
ISO amp ISO amp
VCC/2
100k
100k
100k
100k
250k
250k
250k
250k 250k
1
2
3
4
5
6
7
8
9
10
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
3/26
TSZ22111・15・001
BD37513FS
Absolute Maximum Ratings (Ta=25°C)
Parameter
Power Supply Voltage
Input Voltage
Symbol
VCC
Rating
10.0
Unit
V
VIN
VCC+0.3 to GND-0.3
0.94 (Note)
V
Power Dissipation
Storage Temperature
Pd
W
°C
Tstg
-55 to +150
(Note) This value derates by 7.5mW/°C for Ta=25°C or more when ROHM standard board is used.
Thermal resistance θja = 133.3(°C/W)
ROHM Standard board
Size : 70 x 70 x 1.6(mm3)
Material : A FR4 grass epoxy board(3% or less of copper foil area)
Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over
the absolute maximum ratings.
Recommended Operating Conditions
Parameter
Power Supply Voltage
Temperature
Symbol
Min
7.0
-40
Typ
Max
9.5
Unit
V
VCC
-
-
Topr
+85
V
Electrical Characteristics
(Unless specified otherwise, Ta=25°C, VCC=8.5V, f=1kHz, VIN=1Vrms, Rg=600Ω, RL=10kΩ, A input, Input gain 0dB,
Mute OFF, Volume 0dB, Tone control 0dB, Loudness 0dB, Fader 0dB)
Limit
Parameter
Circuit Current
Symbol
IQ
Unit
mA
Conditions
Min
Typ
Max
48
38
No signal
-
Voltage Gain
Channel Balance
GV
CB
-1.5
-1.5
0
0
+1.5
+1.5
dB
dB
GV=20log(VOUT/VIN)
CB = GV1-GV2
Total Harmonic Distortion 1
(FRONT,REAR)
VOUT=1Vrms
BW=400HZ-30KHz
THD+N1
VNO1
0.001
3.8
0.05
15
-
-
%
Output Noise Voltage 1
Rg = 0Ω
BW = IHF-A
μVrms
(FRONT,REAR)*
Fader = -∞dB
Rg = 0Ω
BW = IHF-A
VNOR
1.8
10
μVrms
Residual Output Noise Voltage*
-
Rg = 0Ω
CTC
RR
-100
-70
-90
-40
dB
dB
CTC=20log(VOUT/VIN)
BW = IHF-A
f=1kHz
VRR=100mVrms
RR=20log(VCC IN/VOUT
Cross-talk Between Channels*
-
-
Ripple Rejection
)
Input Impedance(A,B)
Input Impedance (C,D)
RIN_S
RIN_D
70
175
100
250
130
325
kΩ
kΩ
VIM at THD+N(VOUT)=1%
BW=400Hz-30KHz
Maximum Input Voltage
VIM
2.1
2.3
Vrms
-
Rg = 0Ω
CTS
-100
-90
dB
CTS=20log(VOUT/VIN)
BW = IHF-A
Cross-talk Between Selectors*
-
DP1 and DN input
DP2 and DN input
CMRR=20log(VIN/VOUT
BW = IHF-A
Input gain 0dB
Common Mode Rejection Ratio*
CMRR
GIN_MIN
50
-2
65
0
-
dB
dB
)
Minimum Input Gain
+2
VIN=100mVrms
GIN=20log(VOUT/VIN)
Input gain 20dB
VIN=100mVrms
GIN=20log(VOUT/VIN)
GAIN=+1dB to +20dB
Maximum Input Gain
Gain Set Error
GIN_MAX
GIN_ERR
+18
-2
+20
0
+22
+2
dB
dB
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
4/26
TSZ22111・15・001
BD37513FS
Electrical Characteristics - continued
(Unless specified otherwise, Ta=25°C, VCC=8.5V, f=1kHz, VIN=1Vrms, Rg=600Ω, RL=10kΩ, A input, Input gain 0dB,
Mute OFF, Volume 0dB, Tone control 0dB, Loudness 0dB, Fader 0dB)
Limit
Parameter
Symbol
GMUTE
Unit
dB
Conditions
Min
Typ
Max
-85
Mute ON
Mute Attenuation*
-
-105
GMUTE=20log(VOUT/VIN)
BW = IHF-A
Volume = 15dB
Maximum Gain
GV_MAX
+13
+15
+17
-85
dB
dB
VIN=100mVrms
GV=20log(VOUT/VIN)
Volume = -∞dB
GV=20log(VOUT/VIN)
BW = IHF-A
GV_MIN
-100
Maximum Attenuation*
-
Attenuation Set Error 1
Attenuation Set Error 2
Attenuation Set Error 3
GV_ERR1
GV_ERR2
GV_ERR3
-2
-3
-4
0
0
0
+2
+3
+4
dB
dB
dB
GAIN & ATT=+15dB to -15dB
ATT=-16dB to -47dB
ATT=-48dB to -79dB
Gain=+20dB f=100Hz
VIN=100mVrms
Maximum Boost Gain
+18
+20
+22
dB
GB_BST
GB=20log (VOUT/VIN)
Gain=-20dB f=100Hz
VIN=2Vrms
GB=20log (VOUT/VIN)
Gain=+20dB to -20dB f=100Hz
Gain=+20dB f=10kHz
VIN=100mVrms
Maximum Cut Gain
Gain Set Error
-22
-2
-20
0
-18
+2
dB
dB
dB
GB_CUT
GB_ERR
GT_BST
Maximum Boost Gain
+18
+20
+22
GT=20log (VOUT/VIN)
Gain=-20dB f=10kHz
VIN=2Vrms
GT=20log (VOUT/VIN)
Gain=+20dB to -20dB f=10kHz
Maximum Cut Gain
Gain Set Error
GT_CUT
GT_ERR
-23
-2
-20
0
-17
+2
dB
dB
Fader = -∞dB
Maximum Attenuation*
GF_MIN
-100
-90
dB
-
GF=20log(VOUT/VIN)
BW = IHF-A
GF_ERR1
GF_ERR2
GF_ERR3
-2
-3
-4
0
0
0
+2
+3
+4
dB
dB
dB
ATT=0dB to -15dB
ATT=-16dB to -47dB
ATT=-48dB to -79dB
Attenuation Set Error 1
Attenuation Set Error 2
Attenuation Set Error 3
ROUT
-
50
Ω
VIN=100mVrms
Output Impedance
-
THD+N=1%
BW=400Hz-30KHz
VOM
2
2.2
Vrms
Maximum OutputVoltage
-
Gain 20dB
Maximum Gain
GL_MAX
+17
+20
+23
dB
VIN=100mVrms
GL=20log(VOUT/VIN)
GL_ERR
-2
0
+2
dB
GAIN=+20dB to +1dB
Gain Set Error
VP-9690A (Average value detection, effective value display) filter by Matsushita Communication is used for * measurement.
Phase between input / output is same.
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
5/26
TSZ22111・15・001
BD37513FS
Typical Performance Curves
10
1
10
50
40
30
20
10
0
10kHz
1kHz
1
100Hz
0.1
0.1
0.01
0.001
0.01
0.001
0.001 0.01
0.1
1
10
0
2
4
6
8
10
Output Voltage : VOUT [Vrms]
Supply Voltage : VCC [V]
Figure 2. Total Harmonic Distortion vs Output Voltage
Figure 1. Quiescent Current vs Supply Voltage
5
4
3
25
BASS GAIN : -20dB to +20dB
20
/1dB step
fo : 60Hz Q : 0.5
15
2
10
5
Gain=0dB
1
0
0
-1
-2
-3
-4
-5
-5
-10
-15
-20
-25
10
100
1k
10k
100k
10
100
1k
10k
100k
Frequency [Hz]
Frequency (Hz)
Figure 3. Gain vs Frequency
Figure 4. Bass Gain vs Frequency
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
6/26
TSZ22111・15・001
BD37513FS
Typical Performance Curves - continued
25
1000
100
10
TREBLE GAIN:-20dB to +20dB
/1dB step
fo : 7.5kHz Q : 0.75
20
Din-Audio
IHF-A
15
10
5
0
-5
-10
-15
-20
-25
1
-80 -70 -60 -50 -40 -30 -20 -10
0
10 20
Volume Gain [dB]
10
1k
100k
Frequency [Hz]
Figure5. Treble Gain vs Frequency
Figure 6. Output Noise vs Volume Gain
1000
100
10
1000
100
10
DIN-Audio
IHF-A
DIN-Audio
IHF-A
1
1
-20 -15 -10 -5
0
5
10 15 20
-20 -15 -10 -5
0
5
10 15 20
Treble Gain [dB]
Bass Gain [dB]
Figure 7. Output Noise vs Bass Gain
Figure 8. Output Noise vs Treble Gain
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
7/26
TSZ22111・15・001
BD37513FS
Typical Performance Curves - continued
0
-10
-20
-30
-40
-50
-60
-70
2.5
2.0
1.5
1.0
0.5
0.0
10
100
1k
10k
100k
100
1000 10000
100000
Frequency [Hz]
RLOAD [ohm]
Figure 9. CMRR vs Frequency
Figure 10. Output Voltage vs RLOAD
Figure 11. Advanced Switch 1
Figure 12. Advanced Switch 2
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
8/26
TSZ22111・15・001
BD37513FS
Timing Chart
Control Signal Specification
(1) Electrical Specifications and Timing for bus Lines and I/O Stage
SDA
tBUF
tHD;STAT
tF
tSP
tR
tLOW
SCL
tSU;STOT
Sr
tSU;STAT
tHD;STA
tSU;DAT
tHD;DAT
tHIGH
S
P
P
Figure 13. I2C-bus Signal Timing Diagram
Table 1 Characteristics of the SDA and SCL bus lines for I2C-bus devices
Parameter
Fast-modeI2C-bus
Symbol
fSCL
tBUF
Unit
Min
0
1.3
Max
400
-
kHz
1
2
SCL clock frequency
Bus free time between a STOP and START condition
Hold time (repeated) START condition. After this period, the first clock
pulse is generated
μS
3
tHD;STA
0.6
-
μS
4
5
6
7
8
9
LOW period of the SCL clock
HIGH period of the SCL clock
tLOW
tHIGH
1.3
0.6
-
-
-
-
-
-
μS
μS
μS
μS
ns
Set-up time for a repeated START condition
Data hold time:
Data set-up time
tSU;STA
tHD;DAT
tSU;DAT
tSU;STO
0.6
0.06(Note)
120
0.6
Set-up time for STOP condition
μS
All values referred to VIH Min and VIL Max Levels (see Table 2).
(Note) To avoid sending right after the fall-edge of SCL (VIH min of the SCL signal), the transmitting device should set a hold time of 300ns or more for the SDA
signal.
For 7(tHD;DAT), 8(tSU;DAT), make the setup in which the margin is fully in.
Table 2 Characteristics of the SDA and SCL I/O stages for I2C-bus devices
Fast-modedevices
Parameter
Symbol
Unit
Min
-0.3
2.3
0
Max
+1
5
10 LOW level input voltage:
11 HIGH level input voltage:
VIL
VIH
V
V
Pulse width of spikes which must be suppressed by the input filter.
12
13
tSP
50
0.4
ns
V
LOW level output voltage: at 3mA sink current
VOL1
0
Input current of each I/O pin with an input voltage between 0.4V and
4.5V.
14
II
-10
+10
μA
tHD;STA
:2µs
t
tHD;DAT
tSU;DAT
SU;STO
:2µs
:1µs
:1µs
SCL
tHIGH
:1µs
tBU
:4µs
tLO
:3µs
F
W
SDA
SCL clock frequency : 250kHz
Figure 14. I2C Data Transmission Command Timing Diagram
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
9/26
TSZ22111・15・001
BD37513FS
(2) I2C BUS FORMAT
MSB
Slave Address
8bit
LSB
MSB
Select Address
8bit
LSB
MSB
LSB
S
1bit
A
1bit
A
1bit
Data
8bit
A
P
1bit 1bit
S
= Start condition (Recognition of start bit)
Slave Address = Recognition of slave address. The first 7 bits correspond to the slave address.
The least significant bit is “L” which corresponds to write mode.
A
= ACKNOWLEDGE bit (Recognition of acknowledgement)
Select Address = Select address corresponding to volume, bass or treble.
Data
P
= Data on every volume and tone.
= Stop condition (Recognition of stop bit)
(3) I2C BUS Interface Protocol
(a) Basic Format
S
Slave Address
MSB LSB
A
Select Address
MSB LSB
A
Data
MSB LSB
A
P
(b) Automatic Increment (Select Address increases (+1) according to the number of data.)
Slave Address Select Address Data1 Data2
MSB LSB MSB LSB MSB LSB MSB LSB
(Example) ① Data1 shall be set as data of address specified by Select Address.
S
A
A
A
A
DataN
・・・・
MSB LSB
A
P
② Data2 shall be set as data of address specified by Select Address +1.
③ DataN shall be set as data of address specified by Select Address +N-1.
(c) Configuration Unavailable for Transmission (In this case, only Select Address1 is set.)
Slave Address Select Address1 Data Select Address 2 Data
MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB
S
A
A
A
A
A
P
(Note)If any data is transmitted as Select Address 2 next to data, it is recognized
as data, not as Select Address 2.
(4) Slave Address
MSB
A6
1
LSB
R/W
0
A5
0
A4
0
A3
0
A2
0
A1
0
A0
0
80H
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
10/26
TSZ22111・15・001
BD37513FS
(5) Select Address & Data
Select
Address
(hex)
MSB
Data
LSB
Items
D7
D6
0
D5
D4
D3
0
D2
0
D1
D0
Advanced
switch
ON/OFF
Advanced switch time
of Input Gain/Volume
Tone/Fader/Loudness
Advanced switch time
of Mute
Initial setup 1
01
Initial setup 2
Initial setup 3
Input Selector
02
03
05
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
1
Input selector
Mute
ON/OFF
Input gain
06
0
0
Input Gain
Volume gain
20
28
29
2A
2B
2C
41
44
47
Volume Gain / Attenuation
Fader Attenuation
Fader Attenuation
Fader Attenuation
Fader Attenuation
Fader 1ch Front
Fader 2ch Front
Fader 1ch Rear
Fader 2ch Rear
Test mode 1
Test mode 2
Test mode 3
Test mode 4
1
0
0
1
0
0
0
1
1
0
0
1
0
0
1
1
0
0
0
1
0
0
0
1
0
0
0
1
1
0
1
0
Bass
Boost/
Cut
1
Treble
Boost/
Cut
0
Bass gain
51
54
57
0
0
0
0
0
0
Bass Gain
0
Test mode 5
Treble gain
0
0
0
0
0
0
Treble Gain
Loudness Gain
System Reset
75
FE
Loudness Hicut
0
Loudness Gain
0
1
0
0
1
Advanced switch
Note
1. The Advanced Switch works in the latch part while changing from one function to another.
2. Upon continuous data transfer, the Select Address rolls over because of the automatic increment function, as
shown below.
→01→02→03→05→06→20→28→29→2A→2B→2C
→41→44→47→51→54→57→75
3. For the function of Input Selector etc, Advanced Switch is not used. Therefore, please apply mute on the set side
when changing these settings.
4. When using mute function of this IC at the time of changing input selector, please switch mute ON/OFF while
waiting for advanced-mute time.
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
11/26
TSZ22111・15・001
BD37513FS
Select address 01 (hex)
MSB
D7
Advanced switch time of Mute
LSB
D0
0
1
0
Time
D6
0
D5
D4
D3
D2
D1
0
0
1
1
0.6msec
1.0msec
1.4msec
3.2msec
Advanced
Switch
ON/OFF
Advanced switch time
of Input gain/Volume
Tone/Fader/Loudness
0
0
1
Advanced switch time of
Input gain/Volume/Tone/Fader/Loudness
MSB
LSB
Time
D7
D6
0
D5
0
0
1
1
D4
0
1
0
1
D3
D2
D1
D0
4.7 msec
7.1 msec
11.2 msec
14.4 msec
Advanced
Switch
ON/OFF
Advanced switch
Time of Mute
0
0
MSB
D7
Advanced switch ON/OFF
LSB
D0
Mode
D6
0
D5
D4
D3
D2
0
D1
Advanced switch time
of Input gain/Volume
Tone/Fader/Loudness
OFF
ON
0
1
Advanced switch
Time of Mute
0
Select address 05(hex)
Mode
D7
0
D6
0
D5
0
D4
0
D3
0
0
0
0
D2
0
0
0
0
D1
0
0
1
1
D0
0
1
0
1
Initial
A
B
C
D diff
0
1
1
1
Input SHORT
Prohibition
1
0
0
1
Other setting
Input SHORT : The input impedance of each input terminal is lowered from 100kΩ(TYP) to 6 kΩ(TYP).
(For quick charge of coupling capacitor)
: Initial condition
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
12/26
TSZ22111・15・001
BD37513FS
Select address 06 (hex)
MSB
D7
Input Gain
D3
LSB
D0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Gain
D6
D5
D4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
D2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
0
D1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0dB
1dB
2dB
3dB
4dB
5dB
6dB
7dB
8dB
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
1
9dB
10dB
11dB
12dB
13dB
14dB
15dB
16dB
17dB
18dB
19dB
20dB
Mute
ON/OFF
0
0
:
Prohibition
:
:
:
:
1
1
1
1
1
MSB
D7
0
Mute ON/OFF
D4 D3
LSB
D0
Mode
D6
0
D5
0
D2
D1
OFF
ON
Input Gain
1
Select address 20, 28, 29, 2A, 2B (hex)
MSB
Vol. Fader Gain / Attenuation
LSB
Gain & ATT
D7
D6
0
0
D5
0
0
D4
0
0
D3
0
0
D2
0
0
D1
0
0
D0
0
1
0
0
Prohibition
:
:
:
:
:
:
:
:
0
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
15dB
14dB
13dB
0
0
0
:
:
:
:
:
:
:
:
:
-77dB
-78dB
-79dB
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
1
1
1
1
0
1
1
1
0
0
1
1
0
1
0
1
0
Prohibition
:
:
:
:
:
:
:
:
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
1
-∞dB
(Only 0dB to -∞dB are available at address 28, 29, 2A, 2B.)
: Initial condition
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
13/26
TSZ22111・15・001
BD37513FS
Select address 51, 57 (hex)
MSB
D7
Bass/ Treble Gain
LSB
D0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Gain
D6
D5
D4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
D3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
D2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
D1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
0dB
1dB
2dB
3dB
4dB
5dB
6dB
7dB
8dB
9dB
10dB
11dB
12dB
13dB
14dB
15dB
16dB
17dB
18dB
19dB
20dB
Bass/
Treble
Boost
/cut
0
0
:
1
1
:
1
1
:
1
1
:
1
1
:
0
1
Prohibition
MSB
D7
0
Bass/ Treble Boost/Cut
D4 D3
LSB
D0
Mode
D6
0
D5
0
D2
D1
Boost
Cut
Bass/Treble Gain
1
: Initial condition
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
14/26
TSZ22111・15・001
BD37513FS
Select address 75 (hex)
MSB
Loudness Hicut
D4 D3
LSB
Mode
D7
D6
0
0
1
1
D5
0
1
0
1
D2
D1
D0
Hicut1
Hicut2
Hicut3
Hicut4
0
Loudness Gain
MSB
Loudness Gain
LSB
Gain
D7
D6
D5
D4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
D3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
D2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
D1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
D0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0dB
1dB
2dB
3dB
4dB
5dB
6dB
7dB
8dB
9dB
10dB
11dB
12dB
13dB
14dB
15dB
16dB
17dB
18dB
19dB
20dB
0
Loudness Hicut
Prohibition
:
:
:
:
:
1
1
1
1
1
: Initial condition
(6) About Power ON Reset
Built-in IC initialization is made during power on of the supply voltage. Please send initial data to all addresses
at supply voltage on. And please turn on mute at the set side until this initial data is sent.
Limit
Parameter
Symbol
Unit
Conditions
Min
33
Typ
Max
Rise Time of VCC
tRISE
µsec
V
VCC rise time from 0V to 5V
-
-
VCC Voltage of Release
Power ON Reset
VPOR
4.1
-
-
(7) About External Compulsory Mute Terminal
It is possible to force mute externally by setting an input voltage to the MUTE terminal.
Mute Voltage Condition
GND to 1.0V
Mode
MUTE ON
MUTE OFF
2.3V to VCC
Establish the voltage of MUTE in the condition to be defined.
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
15/26
TSZ22111・15・001
BD37513FS
Application Information
1. Function and Specifications
Function
Specifications
Input selector
Input gain
Mute
・Stereo 3 input
・+20dB to 0dB (1dB step)
・Possible to use “Advanced switch” for prevention of switching noise.
・Possible to use “Advanced switch” for prevention of switching noise.
・Differential 1 input
・+15dB to -79dB (1dB step) , -∞dB
・Possible to use “Advanced switch” for prevention of switching noise.
Volume
・+20dB to -20dB (1dB step)
・Possible to use “Advanced switch” at changing gain
Bass
・Q=1
・fo=100Hz
・+20dB to -20dB (1dB step)
・Possible to use “Advanced switch” at changing gain
・Q=1.25 ・fo=10kHz
・0dB to -79dB, -∞dB
・Possible to use “Advanced switch” for prevention of switching noise.
・20dB to 0dB (1dB step)
Treble
Fader
Loudness
・fo=800Hz
・Possible to use “Advanced switch” for prevention of switching noise.
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
16/26
TSZ22111・15・001
BD37513FS
2. Volume / Fader Volume Attenuation Data
(dB)
+15
+14
+13
+12
+11
+10
+9
+8
+7
+6
+5
+4
+3
+2
+1
0
-1
-2
-3
(dB)
-33
-34
-35
-36
-37
-38
-39
-40
-41
-42
-43
-44
-45
-46
-47
-48
-49
-50
-51
-52
-53
-54
-55
-56
-57
-58
-59
-60
-61
-62
-63
-64
-65
-66
-67
-68
-69
-70
-71
-72
-73
-74
-75
-76
-77
-78
-79
-∞
D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
1
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
1
-4
-5
-6
-7
-8
-9
-10
-11
-12
-13
-14
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
-25
-26
-27
-28
-29
-30
-31
-32
For Fader Volume, only 0dB to -∞dB are available.
:Initial condition
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
17/26
TSZ22111・15・001
BD37513FS
3. Application Circuit
GND
SDA
19
SCL
18
VCC OUTF1 OUTF2 OUTR1 OUTR2
0.1μ
MUTE
10μ
10μ
10μ
10μ
10μ
2.2K
20
17
16
15
14
13
12
11
VCC
GND
I2C BUS LOGIC
■Fader
Gain: 0dB to -79dB/1dB step
★no pop noise
■Loudness
20dB to 0dB/1dB step
★no pop noise
・f0=800
・Hicut1/2/3/4
■2 Band EQ (Tone control)
Gain:+20dB to -20dB/1dB
★no pop noise
・Bass:f0=100Hz,
Q=1.0
★Loudness
・Treble:f0=10kHz
Q=1.25
■Volume
★2 Band EQ
(Tone control)
Gain+15dB to -79dB/1dB step
★no pop noise
■Input Gain
Gain:+20dB to 0dB/1dB step
★no pop noise
★Volume/Mute
★Input Gain
Input selector (3 single-end and 1 stereo ISO)
GND
GND
ISO amp ISO amp
VCC/2
1
100k
100k
100k
100k
250k
250k
250k
250k
250k
2
3
4
5
6
7
8
9
10
10μ
2.2μ
2.2μ
2.2μ
2.2μ
2.2μ
2.2μ
2.2μ
10μ
2.2μ
Single1
GND Isoration
Single2
Single3
Unit
R : [Ω]
C : [F]
Notes on Wiring
①Please connect the decoupling capacitor of the power supply in the shortest possible distance to GND.
②GND lines should be one-point connected.
③Wiring pattern of Digital should be away from that of Analog unit and cross-talk should not be acceptable.
④
SCL and SDA lines of I2C BUS should not be parallel if possible.
The lines should be shielded, if they are adjacent to each other.
⑤Analog input lines should not be parallel if possible. The lines should be shielded, if they are adjacent to each other.
⑥About TEST pin (Pin 12), please leave it as OPEN.
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
18/26
TSZ22111・15・001
BD37513FS
Power Dissipation
About the thermal design of the IC
Characteristics of an IC have a great deal to do with the temperature at which it is used, and exceeding absolute maximum
ratings may degrade and destroy the device. Careful consideration must be given to the heat of the IC from the two
standpoints of immediate damage and long-term reliability of operation.
Reference data
SSOP-A20
1.5
Measurement condition: ROHM Standard board
board Size : 70 x 70 x 1.6(mm3)
material : A FR4 grass epoxy board
(3% or less of copper foil area)
0.94W
1.0
θja = 133.3°C/W
0.5
0.0
85
0
25
50
75
100
125
150
Ambient Temperature : Ta (°C)
Figure 15. Temperature Derating Curve
(Note) Values are actual measurements and are not guaranteed.
Power dissipation values vary according to the board on which the IC is mounted
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
19/26
TSZ22111・15・001
BD37513FS
I/O Equivalent Circuits
Terminal
No.
Terminal
Name
Terminal
voltage
Equivalent Circuit
Terminal Description
A terminal for signal input.
VCC
2
3
4
5
A1
A2
B1
B2
4.25
4.25
4.25
The input impedance is 100kΩ(typ).
100k
GND
VCC
A terminal for signal input.
The input impedance is 250kΩ(typ).
6
7
C1
C2
250k
GND
VCC
Input terminal available to Single/Differential
mode.
The input impedance is 250kΩ(typ).
8
9
DP1
DN
10
DP2
250k
GND
A terminal for external compulsory mute.
If terminal voltage is High level, the mute is
OFF. And if the terminal voltage is Low level,
the mute is ON.
11
MUTE
―
VCC
1.65V
GND
VCC
A terminal for fader and Subwoofer output.
13
14
15
16
OUTR2
OUTR1
OUTF2
OUTF1
4.25
GND
Values in the pin explanation and input/output equivalent circuit are reference values only and are not guaranteed.
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
20/26
TSZ22111・15・001
BD37513FS
I/O Equivalent Circuit - continued
Terminal
No.
Terminal
Name
Terminal
voltage
Equivalent Circuit
Terminal Description
Power supply terminal.
17
VCC
8.5
VCC
-
18
SCL
A terminal for clock input of I2C BUS
communication.
1.65V
GND
VCC
-
19
SDA
A terminal for data input of I2C BUS
communication.
1.65V
GND
VCC
20
1
GND
FIL
0
Ground terminal.
1/2 VCC terminal.
4.25
Voltage for reference bias of analog signal
system. The simple precharge circuit and
simple discharge circuit for an external
capacitor are built in.
50k
50k
GND
TEST terminal
12
TEST
-
Values in the pin explanation and input/output equivalent circuit are reference values only and are not guaranteed.
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
21/26
TSZ22111・15・001
BD37513FS
Operational Notes
1.
2.
Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power
supply pins.
Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the
digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog
block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and
aging on the capacitance value when using electrolytic capacitors.
3.
4.
Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
5.
Thermal Consideration
Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in
deterioration of the properties of the chip. In case of exceeding this absolute maximum rating, increase the board size
and copper area to prevent exceeding the Pd rating.
6.
7.
Recommended Operating Conditions
These conditions represent a range within which the expected characteristics of the IC can be approximately obtained.
The electrical characteristics are guaranteed under the conditions of each parameter.
Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow
instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power
supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and
routing of connections.
8.
9.
Operation Under Strong Electromagnetic Field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may
subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply
should always be turned off completely before connecting or removing it from the test setup during the inspection
process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during
transport and storage.
10.
11.
Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and
unintentional solder bridge deposited in between pins during assembly to name a few.
Unused Input Pins
Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and
extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge
acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause
unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power
supply or ground line.
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
22/26
TSZ22111・15・001
BD37513FS
Operational Notes – continued
12.
Regarding the Input Pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them
isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a
parasitic diode or transistor. For example (refer to figure below):
When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic transistor.
Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual
interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to
operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be
avoided.
Resistor
Transistor (NPN)
Pin A
Pin B
Pin B
B
E
C
Pin A
B
C
E
P
P+
P+
N
P+
P
P+
N
N
N
N
N
N
N
Parasitic
Elements
Parasitic
Elements
P Substrate
GND GND
P Substrate
GND
GND
Parasitic
Elements
Parasitic
Elements
N Region
close-by
Figure 16. Example of monolithic IC structure
13.
About a Signal Input Part
(a) About Input Coupling Capacitor Constant Value
In the input signal terminal, please decide the constant value of the input coupling capacitor C(F) that would be
sufficient to form an RC characterized HPF with input impedance RIN(Ω) inside the IC.
G〔dB〕
C〔F〕
0
RIN
〔Ω〕
A(f)
SSH
f〔Hz〕
INPUT
2
2 fCRIN
A
f
2
1 2 fCRIN
(b) About the Input Selector SHORT
SHORT mode is the command which makes switch SSH =ON of input selector part so that the input impedance
RIN of all terminals becomes small. Switch SSH is OFF when SHORT command is not selected.
The constant time brought about by the small resistance inside and the capacitor outside the LSI becomes
small when this command is used. The charge time of the capacitor becomes short. Since SHORT mode turns
ON the switch of SSH and makes it low impedance, please use it at no signal condition.
14.
15.
About Mute Terminal(Pin 11) when power supply is OFF
There should be no applied voltage across the Mute terminal (Pin 11) when power-supply is OFF.
A resistor (about 2.2kΩ) should be connected in series to Mute terminal in case a voltage is supplied to Mute terminal.
(Please refer Application Circuit Diagram.)
About TEST Pin
TEST Pin, should be OPEN.
Pin 12 are TEST Pins.
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
23/26
TSZ22111・15・001
BD37513FS
Ordering Information
B D
3
7
5
1
3
F
S
-
E 2
Part Number
Package
Packaging and forming specification
E2: Embossed tape and reel
FS: SSOP-A20
Marking Diagram
SSOP-A20(TOP VIEW)
Part Number Marking
LOT Number
BD37513FS
1PIN MARK
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
24/26
TSZ22111・15・001
BD37513FS
Physical Dimension, Tape and Reel Information
Package Name
SSOP-A20
(Max 9.05 (include.BURR))
(UNIT : mm)
PKG : SSOP-A20
Drawing No. : EX132-5001
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
25/26
TSZ22111・15・001
BD37513FS
Revision History
Date
Revision
001
Changes
16.Dec.2015
New Release
www.rohm.com
TSZ02201-0C2C0E100430-1-2
16.Dec.2015 Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
26/26
TSZ22111・15・001
Daattaasshheeeett
Notice
Precaution on using ROHM Products
1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PGA-E
Rev.002
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PGA-E
Rev.002
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
相关型号:
![](http://pdffile.icpdf.com/pdf2/p00270/img/page/BD377-6_1622448_files/BD377-6_1622448_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00270/img/page/BD377-6_1622448_files/BD377-6_1622448_2.jpg)
BD37516
Power Bipolar Transistor, 2A I(C), 45V V(BR)CEO, 1-Element, NPN, Silicon, TO-126, Plastic/Epoxy, 3 Pin
FAIRCHILD
![](http://pdffile.icpdf.com/pdf2/p00270/img/page/BD377-6_1622448_files/BD377-6_1622448_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00270/img/page/BD377-6_1622448_files/BD377-6_1622448_2.jpg)
BD37516STU
Power Bipolar Transistor, 2A I(C), 45V V(BR)CEO, 1-Element, NPN, Silicon, TO-126, Plastic/Epoxy, 3 Pin,
FAIRCHILD
©2020 ICPDF网 联系我们和版权申明